Professional Documents
Culture Documents
Merkel Omegat OMS-S 01
Merkel Omegat OMS-S 01
Merkel Omegat OMS-S 01
Material
Elastomer profile ring
PTFE profile ring
PTFE profile ring Material Code
PTFE glass MoS2 compound PTFE GM201
Operating conditions
Product description
Material PTFE GM201/NBR
Two-piece Merkel seal set for sealing Temperature range in °C
piston rods, consisting of a profile ring Hydraulic oils HL, HLP –30 … +100
with an elastomer profile ring as a pre- HFA fluids +5 … +60
load component. HFB fluids +5 … +60
HFC fluids –30 … +60
Injection moulding machines, steel hy- Percentage contact area Mr >50% up to max. 90% at cutting depth c = Rz/2 and reference line C ref = 0%.
© Merkel Freudenberg Fluidtechnic GmbH | Seals for Fluid Power Catalog 2007
Hydraulics | Rod Seals | Merkel Omegat OMS-S
Design notes
Gap dimension
The decisive factor for the function of the seal is the largest gap dimension occurring
during operation on the non-pressurised side of the seal → Technical Manual. The
permissible value is determine by the pressure as well as the profile width and profile
height.
Profile Max. permissible gap dimension
L Profile 16 MPa 26 MPa 32 MPa 40 MPa
10 10 0,75 0,5 0,4 0,4
12,5 12,5 0,75 0,65 0,55 0,5
15 15 0,75 0,65 0,55 0,5
17,5 17,5 0,75 0,65 0,55 0,5
20 20 0,8 0,7 0,6 0,55
When fitting the Omegat OMS-S the elastomer profile ring is first placed in the hous-
ing groove, then the profile ring is deformed to a kidney shape and sprung into place.
During this process it is to be ensured no sharp kinks are produced in the PTFE profile
ring and that the sealing edge is correctly arranged in relation to the direction of the
pressure. The entire fitting operation is only allowed to be performed over rounded
edges.
© Merkel Freudenberg Fluidtechnic GmbH | Seals for Fluid Power Catalog 2007
Hydraulics | Rod Seals | Merkel Omegat OMS-S
Article list
H L +0,2
20°
Ø D Ø d Ø D2 Ø D1 Ø DF
C
© Merkel Freudenberg Fluidtechnic GmbH | Seals for Fluid Power Catalog 2007
Hydraulics | Rod Seals | Merkel Omegat OMS-S
© Merkel Freudenberg Fluidtechnic GmbH | Seals for Fluid Power Catalog 2007
Hydraulics | Rod Seals | Merkel Omegat OMS-S
H L +0,2
20°
Ø D Ø d Ø D2 Ø D1 Ø DF
C
© Merkel Freudenberg Fluidtechnic GmbH | Seals for Fluid Power Catalog 2007
Hydraulics | Rod Seals | Merkel Omegat OMS-S
© Merkel Freudenberg Fluidtechnic GmbH | Seals for Fluid Power Catalog 2007
The catalog details are based on the practical use may noticeably influence
experience of many years of research the functioning of the seals. Against this
in the development and production of background generalised statements
seals in the Freudenberg Group and on the function of the catalog products
correspond to our current level of know- are not possible. Details in this catalog
how. merely represent general and non-bin-
The sealing action of many catalog ding reference values which make no
products is, however, not only created claim to be valid for every application.
by the component itself. In many We therefore recommend you to always
cases – depending on the specific discuss specific applications with our
application – it depends significantly on consultancy service. In the event of very
the other parameters, such as installa- high and special loads, for example due
tion point, counter surface, pressure, to aggressive media, the seal should be
operating temperature, media to be selected in co-operation with us; trials to
sealed, lubrication, effects of vibration check the functional reliability are often
and any ingress of dirt from outside. indispensable.
These and other unknown factors in
Merkel Freudenberg
Fluidtechnic GmbH
Industriestr. 64
D-21107 Hamburg
Tel.: +49(0)40/75 30 6-0
Fax: +49(0)40/75 30 6-440
E-mail: merkel@freudenberg.de
www.merkel-freudenberg.de
© Merkel Freudenberg Fluidtechnic GmbH | Seals for Fluid Power Catalog 2007