Professional Documents
Culture Documents
Installation Instructions 24si 28si
Installation Instructions 24si 28si
10524210
22AU13 C/P30502 REV4
WARNING!!!!ALWAYS USE PROPER EYE PROTECTION WHEN PERFORMING ANY MECHANICAL REPAIRS TO A VEHICLE
®
- INCLUDING, BUT NOT LIMITED TO, ANY INSTALLATION AND OR REPAIRS TO THE DELCO REMY ALTERNATORS. FAILURE
TO USE PROPER EYE PROTECTION CAN LEAD TO SERIOUS AND PERMANENT EYE DAMAGE.
Only perform the mechanical functions that you are properly qualified to perform. Mechanical repairs that are beyond your technical
capabilities should be handled by a professional installation specialist.
DANGER!!! To avoid injury or damage, always disconnect the negative cable at the battery before removing or replacing the alternator.
The alternator output terminal is always live (“hot”). If the battery is not disconnected, a tool accidentally touching this terminal and
ground can quickly get hot enough to burn skin or damage tools and surrounding parts.
NOTICE! Some of these are extremely high output Alternators. Always ensure your application is equipped with the appropriate
size and gauge cable. CHARGING LINE CABLE VOLTAGE DROP SHOULD NOT EXCEED 0.5 VOLTS (12V system), 1.0 Volts
(24V system) (ALTERNATOR OUTPUT [B+] TERMINAL TO BATTERY POSITIVE TERMINAL AT FULL OUTPUT). FOR
OBTAINING ADDITIONAL WIRING INSTALLATION INFORMATION, SEE HEAVY DUTY APPLICATION MANUALS OR
CONTACT A REMY INC. REPRESENTATIVE.
FOLLOW ENGINE OR VEHICLE MANUFACTURER’S INSTRUCTIONS FOR REMOVING THE OLD ALTERNATOR FROM THE
ENGINE AND INSTALLING THE NEW ALTERNATOR.
INDICATOR/IGNITION
NOTICE - Only licensed Remy International, Inc. product and component parts should be used, and the use of other parts or modifications not approved
by Remy International, Inc. will void all applicable warranties. The failure to carefully follow these Installation Instructions, set forth above, will void all
applicable warranties. DELCO REMY is a registered trademark of General Motors Corporation, licensed to Remy International, Inc. Pendleton, IN 46064.
© 2012 Remy International, Inc. All rights reserved 1 10524210
PULLEY INSTRUCTIONS: Use pulley from old alternator if this alternator does not have one or pulley supplied is different from pulley
on alternator being replaced. NOTICE! When changing the pulley, keep the alternator shaft in the horizontal position and do not
apply any pressure to end of the shaft. Internal damage may occur if the shaft is pushed back and turned. All alternators are
shipped with spacers that go behind the pulley. During installation of the pulley, assure these parts are in the same order as
received. If the old alternator has different spacers, use them and Install on this alternator in same order as removed. Assure the
pulley turns freely prior to installation.
Hold the shaft by placing a hex wrench in the hexagonal hole in the shaft while removing or installing the pulley. Tighten the pulley nut
to 95-108 Nm (70-80 lb ft). Do not install the fan.
BELT TENSIONING INSTRUCTIONS: Improper belt tension can cause premature alternator failure. If the belt must
be tightened manually, place a wood block between the alternator and pry bar, as illustrated at right. Pry as close to
the center of the unit as possible. Use a torque wrench to tighten mounting bolts to the proper torque as specified in
vehicle or engine manufacturer’s specifications for belt tension and mounting bolts torque. DO NOT OVER TIGHTEN
BELT!
FIGURE 2: 24SI & 28SI (4-PIN PLUG TERMINALS) FIGURE 3 - 24SI & 28SI (STUD TERIMINALS)
“B+” Terminal - Output terminal connects to the positive (+) battery terminal.
“S” Remote Sense™ Terminal – Connect to system voltage at the battery or a common distribution point.
“R” Terminal – Relay / Phase terminal carries half system voltage and may be used for certain types of control relays, charge
indicators, tachometers or similar devices. The current draw should not exceed four (4) amperes. Frequency = Alternator RPM/10.
Notice! The “R” Terminal is not the Remote Sense™ terminal – do not connect to B+!
“I” Terminal - The Indicator lamp/ignition terminal can serve as a current source, sink or both, depending on how it is connected. The
diagram above shows one configuration. Current capability is 1.0 Amp in either direction.
Ground Screw – Ground lead ensures alternator is grounded and is strongly recommended for optimum performance.
NOTICE - Only licensed Remy International, Inc. product and component parts should be used, and the use of other parts or modifications not approved
by Remy International, Inc. will void all applicable warranties. The failure to carefully follow these Installation Instructions, set forth above, will void all
applicable warranties. DELCO REMY is a registered trademark of General Motors Corporation, licensed to Remy International, Inc. Pendleton, IN 46064.
© 2012 Remy International, Inc. All rights reserved 2 10524210
♦ If installing this alternator with Remote Sense™ terminal in a vehicle that does not have a sense line, connect a fused
(5 Amp) insulated wire from the Alternator Voltage Sense terminal to the positive (+) battery terminal or the common distribution point at
the starter solenoid battery (+) terminal. Connection of this terminal is best for optimum performance; however, the alternator will
function without Remote Sense™ connected.
Use a #16 gauge red insulated wire, preferably with a 1/4” ID Convoluted Polyethylene Conduit. Also install a standard inline fuse
holder with a protective cap. Use a low voltage automotive standard blade style fuse, 5 Amp.
Only connect the Remote Sense™ terminal line to the Remote Sense™ terminal. The “R” and “I” Terminals are not the Remote
Sense™ Terminal!
PHASE / RELAY
TERMINAL OUTPUT
IS AT 1/2 SYSTEM
VOLTAGE
“B+” Terminal - Output terminal connects to the positive (+) battery terminal.
“S” Remote Sense™ Terminal – Connect to system voltage at the battery or a common distribution point.
“P” Terminal – Relay / Phase terminal carries half system voltage and may be used for certain types of control relays, charge indicators,
tachometers or similar devices. The current draw should not exceed four (4) amperes. Frequency = Alternator RPM/10.
“L” Terminal - The regulator Lamp or “L” terminal connects to the ignition switch through an indicator bulb or LED.
“F” Terminal - Connect to ECU or ECM Field data input terminal.
Ground Screw – Ground lead ensures alternator is grounded and is strongly recommended for optimum performance.
♦ If installing this alternator with Remote Sense™ terminal in a vehicle that does not have a sense line, connect a fused
(5 Amp) insulated wire from the Alternator Voltage Sense terminal to the positive (+) battery terminal or the common distribution point
such as the starter solenoid battery (+) terminal. Connection of this terminal is best for optimum performance; however, the alternator
will function without Remote Sense™ connected.
Use a #16 gauge red insulated wire, preferably with a 1/4” ID Convoluted Polyethylene Conduit. Also install a standard inline fuse
holder with a protective cap. Use a low voltage automotive standard blade style fuse, 5 Amp.
Only connect the Remote Sense™ terminal line from the battery to the Remote Sense™ terminal. The “R” or “I” Terminals are not
the Remote Sense™ Terminal!
.
Technical support: USA 800 854 0076, Mexico 01 800 000 7378, Brazil 0800 703 3526, South America 55 11 2106 6510 or visit
delcoremy.com
NOTICE - Only licensed Remy International, Inc. product and component parts should be used, and the use of other parts or modifications not approved
by Remy International, Inc. will void all applicable warranties. The failure to carefully follow these Installation Instructions, set forth above, will void all
applicable warranties. DELCO REMY is a registered trademark of General Motors Corporation, licensed to Remy International, Inc. Pendleton, IN 46064.
© 2012 Remy International, Inc. All rights reserved 3 10524210
Hoja de Instrucción
10524210
DATE REVISION
® ®
INSTRUCCIONES DE INSTALACION DE ALTERNADORES 24SI & 28SI
Nota: Instrucciones para reemplazar alternadores 21SI, 22SI y 24SI por alternadores 24SI y 28SI visite www.delcoremy.com
¡¡¡PRECAUCIÓN!!!!USE SIEMPRE PROTECCIÓN OCULAR CUANDO REALICE CUALQUIER ACTIVIDAD RELACIONADA CON LA
REPARACIÓN MECÁNICA A UN VEHÍCULO, INCLUYENDO MÁS NO LIMITANDO A CUALQUIER REPARACIÓN O INSTALACIÓN
DE MOTORES DE ARRANQUE DELCO REMY. OMITIR EL USO DE PROTECCIÓN OCULAR APROPIADA PUEDE RESULTAR EN
DAÑOS Y LESIONES PERMANENTES A LOS OJOS.
Ejecute solamente las funciones mecánicas que está apropiadamente calificado para realizar. Las reparaciones mecánicas
que se encuentran fuera de sus capacidades técnicas deben ser manejadas por especialistas profesionales de instalación.
¡¡¡PELIGRO!!! Siempre desconecte el cable negativo (-) de batería antes de remover o reemplazar los cables del alternador. La terminal
de salida del alternador siempre esta viva (“caliente”). Si la batería no es desconectada y una herramienta toca accidentalmente esta
terminal y tierra; puede rápidamente calentarse y provocar quemaduras de piel o dañar la herramienta y partes a su alrededor.
SIGA LAS INSTRUCCIONES DEL FABRICANTE DE LA MAQUINA (MOTOR DE COMBUSTION INTERNA) Y/O DEL VEHICULO AL
MOMENTO DE INSTALAR Y REMOVER EL ALTERNADOR
ALERTA! Algunos de estos alternadores proveen una salida de corriente extrema. Asegure siempre que su aplicación esta provista del
calibre adecuado de cables: LA CAIDA DE VOLTAJE EN EL CABLE DE CARGA NO DEBE EXCEDER 0.5Volts ( SISTEMAS 12V) Y
1.0Volts (SISTEMAS 24V) (TERMINAL DE SALIDA DE ALTERNADOR B+ A LA TERMINAL POSITIVA DE LA BATERIA A SALIDA
TOTAL DE CORRIENTE). PARA OBTENER INFORMACION ADICIONAL DE INSTALACION DE CABLEADO VEA LOS MANUALES
DE APPLICACIONES DE EQUIPO PESADO O CONTACTE SU REPRESENTANTE DE REMY INC.
NOTA - Solamente deben ser usados productos y componentes Remy International Inc., el uso de otras partes o modificaciones no aprobadas por
Remy International Inc. anulará todas las garantías aplicables. No seguir cuidadosamente las instrucciones de instalaciones expuestas en este documento
anulará todas las garantías aplicables. Delco RemyⓇ es una marca registrada de General Motors Corporation, autorizada bajo licencia a Remy
International Inc., Pendleton, IN 46064.
© 2012 Remy International Inc. Todos los derechos 4
INSTRUCCIONES DE POLEA: De ser necesario use la polea del alternador removido. Alerta! Cuando cambie la polea, mantenga
la flecha del alternador en posición vertical y no aplique presión a ningún lado de esta. Un daño interno puede ocurrir si la
flecha es empujada o girada. Si había espaciadores cuando la polea y el ventilador fueron removidos, asegúrese que estos sean
reemplazados cuando se instale la polea en el alternador nuevo. Cuando remueva la polea, asegure la flecha colocando una llave
hexagonal en el receptáculo de la flecha, apriete la tuerca de la polea a 95-108 Nm (70-80 Lb ft).
INSTRUCCIONES DE TENSION DE BANDA: La tensión inapropiada de banda puede crear una falla prematura del
alternador. Si la banda tiene que ser ajustada manualmente, coloque un bloque de madera entre el alternador y
palanca, como se muestra en la ilustración. Haga palanca lo mas cerca al centro de la unidad. Use un torquímetro
para apretar los tornillos de montaje al torque especificado en los manuales del vehiculo o motor de combustión. No
sobre apriete la banda!
FIGURA 2: 24SI & 28SI (CONECTOR DE 4-PINES) FIGURA 3 - 24SI & 28SI (TERMINAL DE TORNILLO)
DESCRIPCION DE TERMINALES (El alternador funcionara aun sin conectar las terminales S, I o R ):
Terminal “B+” - La terminal de salida conecta al positivo (+) de la batería.
Terminal “S” Remote Sense™ – Conecta al voltaje de sistema en la batería o a un punto común de distribución.
Terminal “R” – Terminal Relé / Fase, lleva la mitad del voltaje del sistema y puede ser usada para ciertos tipos de relevadores de
control, indicadores de carga, tacómetros o similares. La demanda de corriente no debe exceder 4 amperes. Frecuencia = RPM
Alternador/10.
¡Alerta! La terminal “R” no es la Terminal Remote Sense™ – no se conecte a la terminal B+!
Terminal “I” - La terminal lámpara / ignición puede servir como fuente de corriente, disipador o ambos, dependiendo como se conecte.
El diagrama arriba muestra una de las configuraciones. La capacidad de corriente es de 1.0 Amp en cualquier dirección.
Terminal Tierra – La terminal tierra asegura que el alternador este aterrizado y es altamente recomendada para optimo desempeño
NOTA - Solamente deben ser usados productos y componentes Remy International Inc., el uso de otras partes o modificaciones no aprobadas por
Remy International Inc. anulará todas las garantías aplicables. No seguir cuidadosamente las instrucciones de instalaciones expuestas en este documento
anulará todas las garantías aplicables. Delco RemyⓇ es una marca registrada de General Motors Corporation, autorizada bajo licencia a Remy
International Inc., Pendleton, IN 46064.
© 2012 Remy International Inc. Todos los derechos 5
♦ Si se instala un alternador con Remote Sense™ en un vehiculo que no tiene cable de sensado, conecte un cable aislado con un
fusible de 5 amperes desde la terminal “Voltage Sense” del alternador a la terminal positiva de la batería o al punto común de
distribución en la terminal batería (+) del solenoide de la marcha. La conexión de esta terminal es lo mejor para un funcionamiento
optimo, sin embargo el alternador funcionara sin la terminal Remote Sense™ conectada.
Use un cable rojo aislado calibre #16, preferentemente con un tubo corrugado de polietileno de 1/4”. También instale un portador de
fusibles estándar con tapa protectora, use un fusible de 5 amperes estándar de tipo espada de bajo voltaje.
Solo conecte el cable de Remote Sense™ a la terminal de Remote Sense™. Las terminales “R” e “I” no son terminales Remote
Sense™!
TACÓMETRO
INDICADOR DE CARGA CABLE #6 O MAYOR
SISTEMA ADLO
CARGA
FRECUENCIA = RPM
10
PRECAUCIÓN: NO EXCEDA 4
AMPS DE CORRIENTE. SISTEMA INDICADOR DE
VOLTAJE DE SALIDA CARGA RECOMENDADO
V = ½ VRMS SISTEMA INTEGRAL TERMINAL MOTOR DEL SOLENOIDE O
DE CARGA PUNTO CERCANO CONECTADO A LA
BATERÍA POR UN CABLE ROBUSTO
DESCRIPCION DE TERMINALES (El alternador funcionara aun sin conectar las terminales S, I o R ):
Terminal “B+” - La terminal de salida conecta al positivo (+) de la batería.
Terminal “S” Remote Sense™ – Conecta al voltaje de sistema en la batería o a un punto común de distribución.
Terminal “P” – Terminal Relé / Fase lleva la mitad del voltaje del sistema y puede ser usada para ciertos tipos de relevadores de
control, indicadores de carga, tacómetros o similares. La demanda de corriente no debe exceder 4 amperes. Frecuencia = RPM
Alternador/10.
Terminal “L” - La terminal reguladora lámpara o Terminal “L” se conecta a la llave de ignición a través de un foco o LED indicador
Terminal “F” - Se conecta al la terminal de datos de campo de la ECU o ECM
Terminal Tierra – La terminal tierra asegura que el alternador este aterrizado y es altamente recomendada para optimo desempeño
♦ Si se instala un alternador con Remote Sense™ en un vehiculo que no tiene cable de sensado, conecte un cable aislado con un
fusible de 5 amperes desde la terminal “Voltage Sense” del alternador a la terminal positiva de la batería o al punto común de
distribución en la terminal batería (+) del solenoide de la marcha. La conexión de esta terminal es lo mejor para funcionamiento optimo,
sin embargo el alternador funcionara sin la terminal Remote Sense™ conectada.
Use un cable rojo aislado calibre #16, preferentemente con un tubo corrugado de polietileno de 1/4”. También instale un portador de
fusibles estándar con tapa protectora, use un fusible de 5 amperes estándar de tipo espada de bajo voltaje.
Solo conecte el cable de Remote Sense™ a la terminal de Remote Sense™. Las terminales “R” e “I” no son terminales Remote
Sense™!
Asistencia Técnica: USA 800 854 0076, México 01 800 000 7378, Brasil 0800 703 3526, Sudamérica 55 11 2106 6510 o visite
delcoremy.com
NOTA - Solamente deben ser usados productos y componentes Remy International Inc., el uso de otras partes o modificaciones no aprobadas por
Remy International Inc. anulará todas las garantías aplicables. No seguir cuidadosamente las instrucciones de instalaciones expuestas en este documento
anulará todas las garantías aplicables. Delco RemyⓇ es una marca registrada de General Motors Corporation, autorizada bajo licencia a Remy
International Inc., Pendleton, IN 46064.
© 2012 Remy International Inc. Todos los derechos 6