Professional Documents
Culture Documents
Attelage Articulé: Spécifications Des
Attelage Articulé: Spécifications Des
Attelage Articulé: Spécifications Des
Ecran précédent
Bienvenue: m400fm
Produit: MOTOR GRADER
Modèle: 12K MOTOR GRADER SZP10190
Configuration: Niveleuse 12K SZP00001-UP (MACHINE) ALIMENTÉE PAR C7
Engine
Spécifications des
niveleuses 12K, 140K, 140K séries 2 et 160K Système hydraulique et de direction
Numéro d'imprimé -KENR8422-03 Date de publication -01/02/2011 Date de mise à jour -24/02/2011
i04136390
Attelage articulé
SMCS - 7057
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpa… 1/3
09/07/2020 12K Motor Grader SZP00001-UP (MACHINE) POWERED BY C7 Engine(SEBP5000 - 41) - Documentation
Illustration 1 g01712119
(1) Lubrifiez légèrement la lèvre d'étanchéité du joint à lèvre avec le lubrifiant qui est scellé.
(2) Tighten two opposite bolts to an equal torque. Tighten the remaining two bolts to an equal torque. Repeat
the procedure until all bolts are at the proper torque.
(3) Center bearing in the bore. Leave 12.7 ± 0.5 mm (0.50 ± 0.02 inch) on a side.
(4) Cool bearing (3) to a temperature of -57° C (-70° F) to -91° C (-132° F) before pressing into bore.
(5) Bolts
3. Ensure that lower cap (9) is flush with front frame (8) .
4. Measure gap (C) between front frame (8) and upper cap (6) at all three bolts. Use the smallest
measurement (C) to determine correct thickness of shims.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpa… 2/3
09/07/2020 12K Motor Grader SZP00001-UP (MACHINE) POWERED BY C7 Engine(SEBP5000 - 41) - Documentation
7. Tighten seven bolts (5) to a final torque of 105 ± 20 N·m (75 ± 15 lb ft).
(10) Bolts
1. Install two bolts (10) . Do not install the bolts in adjacent holes.
2. Tighten the two bolts (10) to a preliminary torque of 135 ± 14 N·m (100 ± 10 lb ft).
3. Measure gap (D) between frame (13) and plate (11) . Use the smallest measurement (D) to determine
the correct thickness of shims.
4. Install shims (12) that are the same thickness as measurement (D) minus 0.25 mm (0.010 inch).
6. Tighten four bolts (10) to a final torque of 240 ± 40 N·m (175 ± 30 lb ft).
Note: Apply Loctite 242 to the threads before installing four bolts (10) . Tighten four bolts (10) in the
sequence that is shown.
(14) Torque for six bolts ... 120 ± 20 N·m (90 ± 15 lb ft)
Copyright 1993 - 2020 Caterpillar Inc. Thu Jul 09 2020 16:28:52 GMT+0200 (heure d’été d’Europe centrale)
Tous droits réservés.
m400fm
Réseau privé pour utilisateurs autorisés de SIS.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpa… 3/3