GTK-XB7

SERVICE MANUAL US Model

Canadian Model
Ver. 1.0 2016.01

AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
(The United States model only)
Left/Right Channel:
With 3 ohms loads, both channels
driven, from 120 10,000 Hz; rated
30 watts per channel minimum
RMS power, with no more than
0.7% total harmonic distortion from
250 milliwatts to rated output.
Amplifier section
The following are measured at
AC 120 V – 240 V, 50/60 Hz
Power Output (rated):
Left/Right Channel: 130 W + 130 W
(at 3 ohms, 1 kHz, 1% THD)
RMS output power (reference):
Left/Right Channel: 235 W + 235 W
(per channel at 3 ohms, 1 kHz, 30%
THD)
Speaker section
Speaker system:
Tweeter + Woofer
Tweeter L/R:
50 mm (2 in) × 3, cone type
Woofer:
160 mm (6 in) × 2, cone type
Inputs
AUDIO/PARTY CHAIN IN L/R:
Voltage 2 V, impedance 10 kilohms
Outputs
AUDIO/PARTY CHAIN OUT L/R:
Voltage 2 V, impedance 600 ohms
SPECIFICATIONS
USB section and supported General
audio formats Power requirements:
(USB) port: AC 120 V, 60 Hz
Type A, maximum current 2.1 A Power consumption:
Supported bit rate: 60 W
MP3 (MPEG1 Audio Layer-3): Standby power consumption:
32 kbps 320 kbps, VBR When BLUETOOTH standby mode is
set to off: 0.5 W (eco mode)
WMA: 32 kbps 192 kbps, VBR
Sampling frequencies: When BLUETOOTH standby mode is
MP3 (MPEG1 Audio Layer-3): set to on: 2.8 W (all wireless network
32/44.1/48 kHz ports on)
WMA: 44.1 kHz Dimensions (W/H/D) (Approx.):
330 mm × 650 mm × 340 mm (13 in
× 25 in × 13 in)
BLUETOOTH section Mass (Approx.):
Communication system: 12 kg (26 lb 16 oz)
BLUETOOTH Standard version 3.0 Quantity of the system:
Output: 1 piece
BLUETOOTH Standard Power Class 2 Supplied accessories:
Maximum communication range: Remote control (1)
Line of sight approx. 10 m (33 feet) 1) R03 (size AAA) batteries (2)
Frequency band: AC power cord (1)
2.4 GHz band (2.4000 GHz –
2.4835 GHz) Design and specifications are subject to
change without notice.
Modulation method:
FHSS (Freq Hopping Spread
Spectrum)
Compatible BLUETOOTH profiles 2):
A2DP (Advanced Audio Distribution
Profile)
AVRCP (Audio Video Remote Control
Profile)
SPP (Serial Port Profile)
Supported codecs:
SBC (Sub Band Codec)
AAC (Advanced Audio Coding)
LDAC
1)
The actual range will vary depending
on factors such as obstacles between
devices, magnetic fields around a
microwave oven, static electricity,
reception sensitivity, antenna’s

HOME AUDIO SYSTEM

performance, operating system, software
application, etc.
2)
BLUETOOTH standard profiles indicate the
purpose of BLUETOOTH communication
between devices.

9-896-261-01
2016A33-1 Sony Video & Sound Products Inc.
© 2016.01 Published by Sony Techno Create Corporation
GTK-XB7

SAFETY CHECK-OUT
License and Trademark After correcting the original service problem, perform the follow-
Notice ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs,
s MPEG Layer-3 audio cAoding screws, and all other exposed metal parts for AC leakage.
technology and patents licensed Check leakage as described below.
from Fraunhofer IIS and Thomson.
s Windows Media is either a registered LEAKAGE TEST
trademark or trademark of Microsoft
The AC leakage from any exposed metal part to earth ground and
Corporation in the United States
and/or other countries. from all exposed metal parts to any exposed metal part having a
s This product is protected by return to chassis, must not exceed 0.5 mA (500 microamperes.).
certain intellectual property rights Leakage current can be measured by any one of three methods.
of Microsoft Corporation. Use or 1. A commercial leakage tester, such as the Simpson 229 or RCA
distribution of such technology WT-540A. Follow the manufacturers’ instructions to use these
outside of this product is prohibited
without a license from Microsoft or
instruments.
an authorized Microsoft subsidiary. 2. A battery-operated AC milliammeter. The Data Precision 245
s The BLUETOOTH® word mark and digital multimeter is suitable for this job.
logos are registered trademarks 3. Measuring the voltage drop across a resistor by means of a
owned by Bluetooth SIG, Inc. and VOM or battery-operated AC voltmeter. The “limit” indication
any use of such marks by Sony is 0.75 V, so analog meters must have an accurate low-voltage
Corporation is under license. Other
trademarks and trade names are
scale. The Simpson 250 and Sanwa SH-63Trd are examples
those of their respective owners. of a passive VOM that is suitable. Nearly all battery operated
s The N Mark is a trademark or digital multimeters that have a 2 V AC range are suitable. (See
registered trademark of NFC Forum, Fig. A)
Inc. in the United States and in other
countries. To Exposed Metal
s Android™ is a trademark of Google Parts on Set
Inc.
s Google Play™ is a trademark of
Google Inc.
s LDAC™ and LDAC logo are
trademarks of Sony Corporation.
s Apple, the Apple logo, iPad, iPhone,
and iPod touch are trademarks of AC
Apple Inc., registered in the U.S. and 0.15 μF 1.5 kΩ voltmeter
other countries. iPad Air and iPad (0.75 V)
mini are trademarks of Apple Inc.
App Store is a service mark of Apple
Inc.
s “Made for iPod,” “Made for
iPhone,” “Made for iPad” mean Earth Ground
that an electronic accessory
has been designed to connect Fig. A. Using an AC voltmeter to check AC leakage.
specifically to iPod , iPhone, or iPad
respectively, and has been certified
by the developer to meet Apple
performance standards. Apple is not
responsible for the operation of this
device or its compliance with safety
and regulatory standards. Please
note that the use of this accessory
with iPod, iPhone, or iPad may affect
wireless performance.
s All other trademarks and registered
trademarks are of their respective
holders. In this manual, TM and ® SAFETY-RELATED COMPONENT WARNING!
marks are not specified.
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!

LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR

LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONC-
TIONNEMENT. NE REMPLACER CES COMPOSANTS QUE
PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DON-
NÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.

2
 GTK-XB7

TABLE OF CONTENTS

1. SERVICING NOTES ............................................. 4 4-7. Schematic Diagram - MAIN Board (4/8) - ..................... 29
4-8. Schematic Diagram - MAIN Board (5/8) - ..................... 30
2. DISASSEMBLY 4-9. Schematic Diagram - MAIN Board (6/8) - ..................... 31
2-1. Disassembly Flow ........................................................... 5 4-10. Schematic Diagram - MAIN Board (7/8) - ..................... 32
2-2. Top Cover Block ............................................................. 6 4-11. Schematic Diagram - MAIN Board (8/8) - ..................... 33
2-3. Fan Unit (M1) ................................................................. 7 4-12. Printed Wiring Board - BT&NFC Board -...................... 34
2-4. PSU Board ...................................................................... 7 4-13. Schematic Diagram - BT&NFC Board - ........................ 34
2-5. MAIN Board ................................................................... 8 4-14. Printed Wiring Board - USB + KEY Board - ................. 35
2-6. USB + KEY Board.......................................................... 9 4-15. Schematic Diagram - USB + KEY Board - .................... 35
2-7. BT&NFC Board .............................................................. 9 4-16. Printed Wiring Board - IR Board -.................................. 35
2-8. CONTROL Board ........................................................... 10 4-17. Schematic Diagram - IR Board - .................................... 35
2-9. Side Panel (R), Side Panel (L) ........................................ 11 4-18. Printed Wiring Board - CONTROL Board - ................... 36
2-10. Main Chassis Block ........................................................ 12 4-19. Schematic Diagram - CONTROL Board -...................... 37
2-11. Bottom Cover + Plate ..................................................... 13 4-20. Printed Wiring Board - LA Board - ................................ 38
2-12. Front Panel Block ........................................................... 14 4-21. Printed Wiring Board - RGBE Board - ........................... 38
2-13. LB Board......................................................................... 15 4-22. Schematic Diagram - LA Board - ................................... 39
2-14. LA Board......................................................................... 16 4-23. Schematic Diagram - RGBE Board - .............................. 39
2-15. RGBF Board ................................................................... 17 4-24. Printed Wiring Board - LB Board - ................................ 40
2-16. RGBE Board ................................................................... 17 4-25. Printed Wiring Board - RGBF Board - ........................... 40
2-17. IR Board .......................................................................... 18 4-26. Schematic Diagram - LB Board - ................................... 41
2-18. Tweeter (SP5).................................................................. 18 4-27. Schematic Diagram - RGBF Board - .............................. 41
2-19. Tweeter (SP3, SP4) ......................................................... 19 4-28. Printed Wiring Board - PSU Board - .............................. 42
2-20. Woofer (SP1, SP2) .......................................................... 20 4-29. Schematic Diagram - PSU Board - ................................. 43

3. TEST MODE ............................................................ 21 5. EXPLODED VIEWS

5-1. Side Panel Section .......................................................... 49
4. DIAGRAMS 5-2. Cabinet Section ............................................................... 50
4-1. Block Diagram - OVERALL Section - ........................... 23 5-3. Top Cover Section........................................................... 51
4-2. Block Diagram - POWER SUPPLY Section - ................ 24 5-4. MAIN Board Section ...................................................... 52
4-3. Printed Wiring Board - MAIN Board - ........................... 25 5-5. Front Panel Section ......................................................... 53
4-4. Schematic Diagram - MAIN Board (1/8) - ..................... 26
4-5. Schematic Diagram - MAIN Board (2/8) - ..................... 27 6. ACCESSORIES ....................................................... 54
4-6. Schematic Diagram - MAIN Board (3/8) - ..................... 28

3
GTK-XB7
SECTION 1
SERVICING NOTES
The SERVICING NOTES contains important information for servicing. Be sure to read this section before repairing the unit.

UNLEADED SOLDER REPAIRING THE BOARDS

Boards requiring use of unleaded solder are printed with the lead- When each boards installed in this unit are defective, replace the
free mark (LF) indicating the solder contains no lead. mounted board.
(Caution: Some printed circuit boards may not come printed with Individual electrical parts that mounted on the each boards cannot
the lead free mark due to their particular size) be replaced.
Printed wiring board and schematic diagram that have been de-
: LEAD FREE MARK scribed on this service manual are for reference.
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.

4
 GTK-XB7
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.

2-1. DISASSEMBLY FLOW

SET

2-2. TOP COVER BLOCK

(Page 6)

2-9. SIDE PANEL (R), SIDE PANEL (L) 2-3. FAN UNIT (M1) 2-7. BT&NFC BOARD
(Page 11) (Page 7) (Page 9)

2-10. MAIN CHASSIS BLOCK 2-4. PSU BOARD 2-8. CONTROL BOARD
(Page 12) (Page 7) (Page 10)

2-11. BOTTOM COVER + PLATE 2-5. MAIN BOARD

(Page 13) (Page 8)

2-12. FRONT PANEL BLOCK 2-6. USB + KEY BOARD

(Page 14) (Page 9)

2-13. LB BOARD 2-17. IR BOARD 2-20. WOOFER (SP1, SP2)

(Page 15) (Page 18) (Page 20)

2-14. LA BOARD 2-15. RGBF BOARD 2-18. TWEETER (SP5)

(Page 16) (Page 17) (Page 18)

2-16. RGBE BOARD 2-19. TWEETER (SP3, SP4)

(Page 17) (Page 19)

‡ JIG
When disassembling the unit, use the following
jig for speaker removal.

Part No. Description

J-2501-238-A JIG FOR SPEAKER REMOVAL

5
GTK-XB7

Note: Follow the disassembly procedure in the numerical order given.

2-2. TOP COVER BLOCK

2 two rubber (circle)

3 screw
3 two screws 4 three screws

5 two rubber
(small circle)
3 screw
6 two screws
3 two screws

1 two rubber (large circle)

8 two screws

7 two rubber (square)

‡)OH[LEOHIODWFDEOH))&WR0$,1VHWWLQJ

flexible flat cable

qa top cover block (FFC (to MAIN))

The opposite side is

the terminal side.

XP35

front side
9 Remove the top cover block
in the direction of the arrow.
0 flexible flat cable (FFC (to MAIN))
(XP35)

6
 GTK-XB7

2-3. FAN UNIT (M1)

3 fan unit (M1)

1 connector (XP14) 2 screw

2 screw

2-4. PSU BOARD

5 five screws

1 two screws

hole
2 reinforcement bracket

ditch hole
hole 6 PSU board
3 connector (XP1)
boss

boss boss

boss

4 connector
(CN501)

– Rear view –

7
GTK-XB7

2-5. MAIN BOARD

6 connector (XP22)
5 connector (XP10)
7 flexible flat cable
(XP45)
4 connector (XP21) ‡:LUHVHWWLQJ
8 connector (XP36) XP10 XP25 flexible flat cable
3 connector (XP14)
2 connector (XP7) front side
9 connector
(XP25)

1 connector
(XP37)

XP21 XP22
XP36 XP45
MAIN board The opposite side is
the terminal side.
XP37 XP7 XP14

– Rear view –
rear side

qa four screws

qd MAIN board

qs Remove the MAIN board in

the direction of the arrow.

0 screw

8
 GTK-XB7

2-6. USB + KEY BOARD

2 USB + KEY board

1 three screws

2-7. BT&NFC BOARD

6 BT&NFC board

4 flexible flat cable (FFC (to BT&NFC)) 1 connector

(XP8) (XP34) 3 flexible flat cable (to MAIN)

‡)OH[LEOHIODWFDEOHWR0$,1VHWWLQJ

Note: Connect the side of short reinforcement plate
to the BT&NFC board.
5 BT board adhesive sheet

2 Peel off the

adhesive sheet.

front side
BT&NFC board XP34
short

The opposite side is

the terminal side.
top cover block

rear side flexible flat cable

claw (to MAIN)

top side

long

9
GTK-XB7

2-8. CONTROL BOARD

2 eight screws
3 plate

5 flexible flat cable (FFC (to BT&NFC))

(XP16)
6 CONTROL board
The opposite side is the terminal side.

1 connector
(XP8)
4 Remove the CONTROL board block
in the direction of the arrow.

front side

top cover block

rear side
top side

10
 GTK-XB7

2-9. SIDE PANEL (R), SIDE PANEL (L)

5 side panel (R)

Note: When installing the side panel (R),
remove the used bond and use a new
bond to fix the side panel (R).

4 Remove the side panel (R)

in the direction of the arrow.
bond

1 rubber
(large circle)
3 four screws
2 screw 4 Remove the side panel (L)
in the direction of the arrow.
1 rubber (large circle)

2 screw
bond

3 screw

3 four screws

– Rear view –

3 screw

5 side panel (L)

Note: When installing the side panel (L),
remove the used bond and use a new
2 two screws
bond to fix the side panel (L).

1 two rubber (circle)

11
GTK-XB7

2-10. MAIN CHASSIS BLOCK

4 flexible flat cable

3 connector (XP45)
(XP22)

2 connector 5 connector
(XP10) (XP36)

6 connector
1 connector
(XP25)
(XP21)
‡:LUHVHWWLQJ
XP10 XP25 flexible flat cable
front side

XP21 XP22
XP36 XP45
MAIN board The opposite side is
the terminal side.

7 seven screws

– Rear view –

8 main chassis block

12
 GTK-XB7

2-11. BOTTOM COVER + PLATE

1 two rubber (square)

2 two screws

top side

4 two screws

3 two rubber (small circle)

bottom side

‡+RZWRUHPRYHWKHERWWRPFRYHUSODWH
Note 1: When removing the bottom cover + plate, move the bottom
cover + plate slowly and remove the bond as shown figure.
Note 2: When removing the bottom cover + plate, please remove
carefully so as not to damage the bosses.

two bosses

bond

7 Remove the bottom cover + plate

in the direction of the arrow.
6 four screws

5 four rubber (large circle)

8 bottom cover + plate
Note 3: When installing the bottom cover + plate,
remove the used bond and use a new
bond to fix the bottom cover + plate.

13
GTK-XB7

2-12. FRONT PANEL BLOCK

total nine bosses front panel block

5 All bosses are removed while moving
cushion jig in the direction of the arrow, and
front panel block is removed.

4 Insert the jig into a space and raise

front panel block.
cushion
Note 1: When using a jig, please work
so as not to injure the cushion.
top side
3 prop (bottom)

5 All bosses are removed while moving 1 screw

jig in the direction of the arrow, and
front panel block is removed.
2 four screws

4 Insert the jig into a space and raise bottom side

front panel block. 1 screw
Note 1: When using a jig, please work
so as not to injure the cushion.

speaker unit (TW) (SP4)

8 front panel block

Note 2: When installing the front panel block
remove the used bond and use a new
bond to fix the front panel block.
7 tweeter terminal
(wide side)

7 tweeter terminal
(narrow side)

6 Remove the front panel block

in the direction of the arrow.

14
 GTK-XB7

2-13. LB BOARD

front panel block

front side

4 connector (XP37)

3 connector (XP56)

bottom side

2 Remove the LB board block

in the direction of the arrow.

1 eight screws
5 connector (XP50)

6 LB board

15
GTK-XB7

2-14. LA BOARD

top side

3 prop (upper) front panel block

1 four screws
front side

2 Draw two cables

out from the hole.

‡:LUHVHWWLQJ
XP55
XP38 XP54

LA board
cable

flexible flat cable The opposite side is

the terminal side.
–)URQWYLHZ–
‡:LUHVHWWLQJ
5 Remove the LA board block
in the direction of the arrow. LA board
groove

8 connector (XP55)
two cables
7 connector (XP54)

4 three screws
groove
groove

6 flexible flat
cable qa LA board
(XP38)
4 three screws

front panel
block

0 cable

9 Remove two cables from four

grooves of the front panel.

16
 GTK-XB7

2-15. RGBF BOARD

‡+RZWRLQVWDOOWKH5*%)ERDUG
mounting plate (bottom right)

front panel block

boss

Install the RGBF board Make sure that the projection

into the slot. of the RGBF board is out. front side

slot
bottom side
hole
3 RGBF board
1 two screws
hole

2 mounting plate (bottom right)

2-16. RGBE BOARD

‡+RZWRLQVWDOOWKH5*%(ERDUG
Install the RGBE board Make sure that the projection
into the slot. of the RGBE board is out.
top side

boss

– Rear bottom view – mounting plate (bottom left) front panel block

2 mounting plate
(bottom left) front side
slot

hole

3 RGBE board
1 two screws

17
GTK-XB7

2-17. IR BOARD

top side

3 flannel
2 IR board

front panel block

1 screw
front side

2-18. TWEETER (SP5)

front panel block

front side

2 speaker plate
bottom side

3 tweeter terminal
(wide side)
3 tweeter terminal
(narrow side)
1 two screws 4 speaker unit (TW) (SP5)

18
 GTK-XB7

2-19. TWEETER (SP3, SP4)

top side

front panel block

4 speaker unit (TW)

(SP3)
2 speaker plate
front side
3 tweeter terminal
(wide side)

1 two screws 3 tweeter terminal

(narrow side)
7 speaker unit (TW)
(SP4)

6 speaker plate
5 two screws

19
GTK-XB7

2-20. WOOFER (SP1, SP2)

‡:LUHVHWWLQJ

woofer terminal
(wide side) speaker unit (WF) (SP2)

woofer terminal front side

(narrow side)

2 Remove the speaker unit (WF)

in the direction of the arrow.

3 woofer terminal
(narrow side)
3 woofer terminal
(wide side)

4 speaker unit (WF)

(SP2)

1 four screws 3 woofer terminal

(narrow side)

‡,QVWDOODWLRQGLUHFWLRQIRUWKHVSHDNHUXQLW:)6363

3 woofer terminal Note: When installing the speaker unit (WF) (SP1), (SP2), make
1 four screws (wide side) sure that there is a position of the speaker terminal to the
position shown in the figure below.
top side

4 speaker unit (WF)

(SP1)
speaker unit (WF) (SP2)
‡:LUHVHWWLQJ
woofer terminal
speaker unit (WF) (SP1) (narrow side)

terminals position

speaker unit (WF) (SP1)

–)URQWYLHZ–

front side woofer terminal

(wide side)

20
 GTK-XB7
SECTION 3
TEST MODE
SOFTWARE VERSION DISPLAY
It can confirm the software version.

Procedure:
1. Press the [1] button to turn the power on.
2. Press the [FUNCTION] button to select the AUDIO IN func-
tion.
3. Press the button on the remote commander as following order.
[>] → [EXTRA BASS] → [.]
4. Each software versions are shown by the blinking frequency of
LEDs simultaneously.

Example:
When the MCU version is “v15”, the [1] LED blinks 1 time, the
[EXTRA BASS] LED blinks 5 times.
When the MPEG version is “v07”, the [AUDIO IN] LED blinks 0
time, the [USB] LED blinks 7 times.
When the BT version is “v075”, the [SPEAKER ADD L] LED
blinks 0 time, the [SPEAKER ADD R] LED blinks 7 times, the
[PARTY CHAIN] LED blinks 5 times.

FACTORY RESET
It can reset all MPEG settings and clear the Bluetooth linked list.
Execute this mode when returning the this unit to the customer.

Procedure:
1. Press the [1] button to turn the power on.
2. Press two buttons of the [FUNCTION] and [–] simultaneously
for 5 seconds.
3. The [1] LED blinks for 3 seconds, and then reboot the system.

21
GTK-XB7

MEMO

22
 GTK-XB7
SECTION 4
DIAGRAMS
4-1. BLOCK DIAGRAM - OVERALL Section -

GTK-XB7
23 23
 GTK-XB7

4-2. BLOCK DIAGRAM - POWER SUPPLY Section - THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
For Printed Wiring Boards. For Schematic Diagrams.
Note: Note:
• : Pattern from the side which enables seeing. • All capacitors are in μF unless otherwise noted. (p: pF) 50
(The other layers’ patterns are not indicated.) WV or less are not indicated except for electrolytics and
tantalums.
Caution: • All resistors are in Ω and 1/4 W or less unless otherwise
Pattern face side: Parts on the pattern face side seen specified.
(Conductor Side) from the pattern face are indicated.
Parts face side: Parts on the parts face side seen from Note: Note:
(Component Side) the parts face are indicated. The components identi- Les composants identifiés
fied by mark 0 or dotted par une marque 0 sont
line with mark 0 are criti- critiques pour la sécurité.
cal for safety. Ne les remplacer que par
Replace only with part une pièce portant le nu-
number specified. méro spécifié.

• Circuit Boards Location

PSU board
BT&NFC board
CONTROL board

USB + KEY board

LA board

IR board MAIN board

RGBE board

LB board

RGBF board

GTK-XB7
24 24
 GTK-XB7

4-3. PRINTED WIRING BOARD - MAIN Board - • See page 24 for Circuit Boards Location. • : Uses unleaded solder.

1 2 3 4 5 6 7 8 9
MAIN BOARD (COMPONENT SIDE)

MAIN BOARD (CONDUCTOR SIDE)

GTK-XB7
25 25
GTK-XB7

4-4. SCHEMATIC DIAGRAM - MAIN Board (1/8) - • See page 44 for IC Block Diagrams.

1 2 3 4 5 6 7 8

MAIN BOARD (1/8)

A XP1
36V 36V_MAIN
1 PSON
1 V_12V 36V_MAIN
2
2 3 C278 0.01uF/50V/X7R L10 22uH/3.6A FB11 120/2A
3 STB_5V
4
4 FB13 120/2A
POWER INPUT 5
5
6
C1 C4
U3
EUP3490
6 7

100pF/50V/NP0

0.1uF/50V/X7R
7 C5 C2 R375 FB5
8
8 NC/5.6Ÿ 120/2A
9 1 3

0.1uF/50V/X7R

100pF/50V/NP0
9 BS SW
9PIN/2.0mm R20
R140 R4
2 5 33
IN FB 68K/1% 51K/1%
C330
NC/330pF/50V 8
7 OVEN
OCSET

COMP

GNDP
C6 C24

GND
ZD2

C26
CE1

C3
+ ZMM6V2/6.2V

0.1uF/16V/X7R
36V AMP_36V 10uF

9
1uF/50V/X7R

0.1uF/50V/X7R
100uF/50V
CE2
+

B
C22 C109 D1
R170 1500pF/50V/X7R R115 R153
220K

330pF/50V/X7R

470uF/10V
15K/1% 10K/1%

SS34/40V/3A
STB_5V
U23 VCC_D
4 R57
VIN 4.7K
1 5 FB4 120/2A
SS VOUT
R101 1K 3 2
POWER_EN EN GND Close to VIN R966 VOUT=0.92*(68+15)/15=5.09V
C164 C162 2.2
C165
EUP3504 R100 1uF/16V Voven=1.02*(10+51)/10=6.22V
1uF/16V 0.01uF/50V/X7R 20

36V_MAIN
C284 0.01uF/50V/X7R L11 22uH/3.6A
+12V

POWER CONTROL 5V U4
EUP3490
FB6

C
120/2A
1 3
BS SW
R69 R5
2 5 R158
IN FB NC/33 200K/1%
220K/1%
+12V V_12V 8
7 OVEN
FB16 120/2A OCSET

COMP

GNDP
S D C9 C28

GND
STB_3.3V

C27
STB_5V U32

CE7

C10
Q2 ZD3
SY8089 C19 R11 +

G
P_AP2305 BZV55C15
4 3 L18 2.2uH/3.4A 0.1UF 47K 10UF 0.1uF

9
1uF/50V/X7R
VIN LX

0.1uF/50V/X7R
100uF/50V
CE5
C399

C203

C389
+
C23 C114 D3
R22
R335 R206 1500pF/50V/X7R

100uF/16V
47K R157 R163
100pF/50V/NP0

33pF/50V/NP0

2.2uF
220K

NC/330pF/50V/X7R
82K/1% 18K/1% 15K/1%

SS34/40V/3A
R13

GND
1 5 CE12 C48 C391 47K
EN VFB +
R75

100uF/16V/SMD

1000pF/50V/X7R
4.7K

10uF/6.3V/X5R
D5 LL4148 3.3V_D1_EN

2
R336
POWER_EN R239 10K Q4
18K/1%
NPN_3DG3904M Close to VIN R967
VOUT=0.6*(82+18)/18=3.3V C21
2.2 VOUT=0.92*(220+18)/18=12.16V

D
R236
47K 0.1UF Voven=1.02*(200+15)/15=14.62V

STB_5VĺSTB_3.3V
POWER CONTROL 12V
C47 0.01uF/50V/X7R

USB_5V
STB_3.3V U14
3.3V_D2
AS5430A
+12V 3 L12 10uH/5A 2.1A
FB15 120/2A 1 SW
STB_3.3V 3.3V_D1 S D BS
Q13
C127 R43 FB7 120/2A 2 5 R380

G
FB14 120/2A P_AP2305 IN FB R16
S D 0.1UF 100K 68K/1% 2.2K
Q11 CE8 C14 C25
C29 R10 C183
G

P_AP2305 + 7 6
0.1UF 100K R253

GND
EN COMP
100K

SS

TP
100uF/16V

0.1uF/16V/X7R
0.1uF CE11 10uF
R204
C152 +
1K

E
R79

4
3900pF/50V/X7R

100uF/16V
15K/1%
R203
1K R28 10K Q17 R373 C189 R259
3.3V_D2_EN 47K 0.1uF C190 6.8K
NPN_3DG3904M 0.1uF

3.3V_D1_EN C41
R27
47K 0.1UF

VOUT=0.925*(68+2.2+15)/15=5.25V

POWER CONTROL 3.3V

POWER CONTROL 3.3V

U2 U19
SGM203-2ADJ3 1.8V_D 3.3V_D2
CW1117 1.2V_D
close to LDO 1 5
3.3V_D1 VIN VOUT 3 2
input Vout

ADJ/GND
C17 C16 R23 C75 C155 4

F
0.1UF 47K 3 4 R21 Out
10uF/6.3V/X5R

EN ADJ/SENSE
C206

15K/1% R44

C146

C128
4.7uF 1uF
GND C30 NC/120/1%
1
2

10uF/6.3V/X5R

0.1UF

10uF/6.3V/X5R

0.1UF
R19
12K/1% Vout=1.25*(1+R25/R44)=1.25V R25
Vout=0.8*(1+15/12)=1.8V
0

3.3Vĺ1.8V 3.3Vĺ1.2V

GTK-XB7
26 26
 GTK-XB7

4-5. SCHEMATIC DIAGRAM - MAIN Board (2/8) -

1 2 3 4 5 6 7 8 9

MAIN BOARD (2/8)

A 3.3V_D2
D33 F3V3
FLASH
F3V3
Crystal
XP2
R31 100K C46
1
DEBUG_TX 2 1
2 0.1UF
DEBUG_RX 3 R39 R40 R41
3 XI Y1 27MHz/30PPM R32 1K XO 10K
4 10K 10K
4 F3V3
C42

C43

C44

4PIN/2.0mm C39 C40 U5

33pF/50V/NP0 33pF/50V/NP0 SF_CS 1 8

R36
100pF/50V/NP0

100pF/50V/NP0

100pF/50V/NP0

RF3.3V
CE# VDD

VCC1.2

VCC1.2

VVCC3
SPI_D0 2 7
3 SO HOLD# 6 R45 33 SF_CK

D33

D33
WP# SCK

USB_DM
USB_DP
Put these circuits as 4 5 SPI_D1
VSS SI
closer as possible to

VVCC3

VVCC3
1K
KH25L1606 16M FLASH

C45
MPEG DECODER. C72
4.7UF

TP3
TP4
TP5
0.1UF
C49

USB_DM
USB_DP

V_FSADJ
10UF/6.3V/X5R
AOUT_R

XO
XI
AOUT_L

102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
3.3V_D2
TP6

APC_AVSS
OPVIN
OPVIP

TV_AVDD
TV_AVSS
TV_AVDD
E

RFSUM

AGCCAP

TV_DAC0
F
A
B
C
D

RFIS

AD_AVDD
AD_AVSS
LDSW/GPIO67
HOME/GPIO66
VDD_12

PLL_VDD
PLL_VSS
USB_AVSS
USB_DM
USB_DP
USB_AVDD
VDD_12
TV_AVSS
TV_DAC3
TV_DAC2
TV_DAC1

V_FSADJ

AOUT_R
AOUT_L
CLKOUT
CLKIN

V_COMP
FB8 500/200mA
D33
C55

C52

C57
C56
C53

Digital 103
104 NC ADAC_AVSS
64
63 C58 10uF/6.3V/X5R
1000pF/50V/X7R
0.1UF

0.1UF
10uF/6.3V/X5R

0.1UF

CDLDO ADAC_AVDD AVCC3

105 62 DAC_VREF C59 0.1UF
106 NC VREF 61
107 CDMDI AIN_R 60
RF3.3V SRV_AVDD AD_AVDD AD_VCC3
TP7 108 59
109 V21 AD_AVSS 58 R133 33 I2S_MCLK R50 33 R240 0
Close to 8104WW V165 GPIO54 BT_MFB_MPEG MCLK_1 AD_MCLK
110 57 R127 33 BCLK_1 I2S_BCLK R52 33 R241 0 AD_BCLK
FB9 500/200mA DA_AVSS GPIO53 AMP_RESET 11
SD33 111 56 LRCLK_1 I2S_LRCK R54 33 R242 0 AD_LRCK
DA_TEO GPIO52
C63 C88 C7
SDRAM RFDA3.3V
112
113 DA_FEO
DA_AVDD
U6 GPIO51
GPIO50
55
54
DATA_IN_1 I2S_DATA_IN R56 33
DATA6
4.7UF 4.7UF 0.1UF
114 53 R112 4.7K C66 C130 C129 SRC_MCLK
SPDC_OUT/GPIO70 SPDIF_IN/GPIO48 STB_3.3V R59
115 52
AMP_FAULT R66 116 SC_OUT/GPIO71 SPHE8104W-128 SPDIF_OUT/GPIO47 51 M_A3
R139 4.7K 1K SRC_BCLK

5.6pF/50V/NP0

5.6pF/50V/NP0

5.6pF/50V/NP0
33 SRC_LRCK
AMP_FAULT GPIO72 M_A3
Close to SDRAM TP8 117 50 M_A2
118 DMEA M_A2 49

C
I2C_SW I2C_SW M_A1
CARD_SENSE/GPIO74 M_A1 R90 33 MCU_SDA
I2C_SCL I2C_SCL TP59 119 48 M_A0 I2C1_SDA
RF3.3V I2C_SDA TP60 120 SD_D0/GPIO75 M_A0 47 M_A10
I2C_SDA SD_CLK/GPIO76 M_A10 R91 33 MCU_SCL
121 46 M_BA1 I2C1_SCL
C325 C67 C68 SD_SMD/GPIO77 M_BA1
RF TP58
122
123 GPIO78 M_BA0
45
44
M_BA0
M_RAS
0.1UF
10uF/6.3V/X5R

0.1UF

124 GPIO79 M_RAS 43 M_CAS

SF_CS 125 CDVR M_CAS 42 M_WE
SPI_D0 126 SPI_CE M_WE 41 M_DQM0
Close to 8104WW TP9 SPI_D0 M_DQM0 M_A[0..11] MA[0..11] (3)
SF_CK 127 40 M_A4 M_D[0..15]
SPI_D1 128 SPI_CLK M_A4 39 M_A5 DQ[0..15] (3)

HSYNC/GPIO7
VSYNC/GPIO8
R62 0 SPI_D1 M_A5 D33 M_BA[0..1]
AD_VCC3 BA[0..1] (3)

IR_IN/GPIO3
VFD_DATA
1.2V_D TP13

RESET_B
VFD_CLK
VFD_STB
M_DQM[0..1]
Internal AD

M_DQM1
C70 C71 DQM[0..1] (3)

VDD_33

VDD_12

VDD_33
GPIO86

M_CLK
RAM_CLK

M_D15
M_D14
M_D13
M_D12
M_D11
M_D10

M_A11
GPIO4
GPIO5
4.7UF DCLK (3)

M_D0
M_D1
M_D2
M_D3
M_D4
M_D5
M_D6
M_D7

M_D9
M_D8

M_A9
M_A8
M_A7
M_A6
0.1UF VCC1.2

VSS

VSS
C80 C81 C82 R30 R37 M_CAS
Close to 8104WW 1K 1K CAS# (3)
M_RAS

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
0.1UF 0.1UF 1000pF/50V/X7R RAS# (3)
M_WE
TP10 WE# (3)

R64
I2C_SDA R33 33 SDRAM

R65 GPIO25
DSP_SDA

MPEG_RX
I2C_SCL

I2S_MCLK
R42 33

MPEG_TX
I2S_LRCK
Close to 8104WW

I2S_DATA_IN
VVCC3

I2S_BCLK
DSP_SCL

M_DQM1
C73

C74

M_D15
M_D14
M_D13
M_D12
M_D11
M_D10
Video DAC

M_D0
M_D1
M_D2
M_D3
M_D4
M_D5
M_D6
M_D7

M_D9
M_D8

M_A9
M_A8
M_A7
M_A6
C64

33
D
4.7UF
0.1UF

0.1UF

RF3.3V RFDA3.3V
STB_3.3V

D33
R167 4.7K
FB12 500/200mA D33

VCC1.2
D33
TP12 R89 4.7K

M_A11 0
R98 4.7K
RAM_CLK
R68 2.2 R70 R71

MPEG_RST
AVCC3 C76
C65 10K 10K
0.1UF R49 R51 C77
4.7UF
CE9 + C78 Internal DA 33 33 5.6pF/50V/NP0
I2S_DATA_OUT

100uF/16V/SMD 0.1UF MPEG_RX R73 1K BT_TX

BT_TX 8

MPEG_TX R74 1K BT_RX

BT_RX 8

debug_RX
debug_TX

3.3V_D2

C54 R55
10uF 10K
TP14

E R46 1K MPEG_RST MPEG_RST

R53 D18 C102

10K LL4148 0.1uF/16V/X7R
Q5
NPN_3DG3904M

RESET

GTK-XB7
27 27
GTK-XB7

4-6. SCHEMATIC DIAGRAM - MAIN Board (3/8) -

1 2 3 4 5 6 7 8 9

MAIN BOARD (3/8)

A
SDRAM
U8

MA0 23 2 DQ7
MA1 24 A0 DQ0 4 DQ6
A1 DQ1 DQ[0..15]
MA2 25 5 DQ5 (2) DQ[0..15]
MA3 26 A2 DQ2 7 DQ4
A3 DQ3 (2) MA[0..11] MA[0..11]
MA4 29 8 DQ3 BA[0..1]
SD33 A4 DQ4 (2) BA[0..1]
MA5 30 10 DQ2 DQM[0..1]
(2) DQM[0..1]

B
MA6 31 A5 DQ5 11 DQ1
A6 DQ6 (2) DCLK DCLK
MA7 32 13 DQ0
MA8 33 A7 DQ7 42 DQ8
A8 DQ8 (2) CAS# CAS#

C100
MA9 34 44 DQ9

C95

C96

C97

C98

C99
A9 DQ9 (2) RAS# RAS#
MA10 22 45 DQ10
A10/AP DQ10 (2) WE# WE#
MA11 35 47 DQ11
A11 DQ11

1000pF/50V/X7R

0.1UF
20 48

0.1UF

0.1UF
DBA0 DQ12

0.1UF

0.1UF
DBA1 21 BA0/A13 DQ12 50 DQ13
BA1/A12 DQ13 51 DQ14
SDCLK 38 DQ14 53 DQ15
37 CLK DQ15
SD33 CKE SD33
19 1
DRAS# 18 CS VCC 14
RAS VCC DRAS# RAS#
DCAS# 17 27 MODE CHG_EN BT_update_EN USB_EN
DWE# 16 CAS VCC SD33
WE DWE# WE#
3
DQM0 15 VCCQ 9 USB sync H X H
DQML VCCQ DCAS# CAS#
DQM1 39 43
DQMH VCCQ 49
VCCQ DBA0 BA0
36 USB charge L L H
40 NC 6
NC VSSQ DBA1 BA1
12
54 VSSQ 46 BT sync L H L
VSS VSSQ SDCLK DCLK
41 52
28 VSS VSSQ

C
VSS

SDRAM_64Mb_M12L64164A-7T
S=1:2ĺON 1ĺOFF
CHARGE_SWITCH S=0:1ĺON 2ĺOFF

STB_3.3V

10
U9

8
S

Vcc

OE
D+ 1 7 USB_DP USB_DP
D+ HSD2+
STB_3.3V D- 2 6 USB_DM USB_DM
D- HSD2-
CHG_EN

HSD1+
HSD1-
D

GND
R95

R96

ESD1 SGM7227

5
Compatible for footprint NC/PRTR5V0U2X
R94
U10 10K
USB_VCC1 R771 NC/0

HSD+
GMT_G527

HSD-
USB_5V XP37

1
4.7K

4.7K

1
USB_5V 6 1 1
IN OUT 1 USB_VCC1 FL1 ELE900 2
USB_EN USB_EN 4 2
EN D- 4 3 3
USB_FAULT USB_FAULT 3 2 3
FLG GND D+ 1 2 4
5 C8 C101 4
ILIM
+ CE14 C34 0.1uF/50V/X7R 100pF/50V/NP0 4PIN/2.0mm
CE16 C79 C35 C11 C38 1uF/16V R772 NC/0
+ 220uF/16V
R102
10uF/16V/X5R

1uF/16V

0.1uF/50V/X7R

1uF/16V

15K/1%
220uF/16V

XP7
1
R830 2 1
R266 ADC_KEY 0
R831 3 2
1K/1% Blue_LED5 0
R832 4 3
Blue_LED6 0
4
Blue_LED7
R833 0 5
6 5 BM update_SWITCH

C371 100pF/50V/NP0
C372 100pF/50V/NP0
C373 100pF/50V/NP0
C374 100pF/50V/NP0
6
6PIN/2.0mm

E R102+R266=16K,Ilim=2.25A_min,2.5A_typ
STB_3.3V

10
USB PORT
U11

8
USB POWER SWITCH

Vcc

OE
HSD+ 1 7
D+ HSD2+ BM_D+
R779 NC/0
HSD- 2 6
D- HSD2- BM_D-
BM_update_EN

HSD1+
HSD1-
GND
SGM7227

5
R111
10K

GTK-XB7
28 28
 GTK-XB7

4-7. SCHEMATIC DIAGRAM - MAIN Board (4/8) - • See page 44 for IC Block Diagrams.

1 2 3 4 5 6 7 8 9

MAIN BOARD (4/8)

A
STB_3.3V MCU_3.3V 3.3V_D1
3.3V_D1

FB48 500/800mA Close to MCU LED Driver R58 0

C341 C342 C344 C345 C347

C318 C319
0.1UF

0.1UF

0.1UF

0.1UF

0.1UF
10uF

Party_Chain_SW
Party_Chain_Out
R218 R219 0.1UF

Party_Chain_In
I2C1_SDA
I2C1_SCL
NC/4.7K NC/4.7K U1

SW_G3157
Blue_LED2
Blue_LED1

Blue_LED5
Blue_LED6
Blue_LED7
NFC_INT
R113 1M 1 24
2 GND VDD 23 R540 11K
Y3 SPI3_MOSI SDI REXT
3 22 SPI3_MISO
YO R956 1K YI SPI3_SCK CLK SDO
4 21 PWMCLK
SPI3_LE 5 LE PWMCLK 20

SWCLK
14.7456MHz/30PPM PWM4_G OUT0 OUT15

MCU_3.3V
6 19

R148

R399

R278
PWM4_B OUT1 OUT14 PWM5_G
C112 C113 PWM4_R 7 18 PWM5_R
27pF/50V/NP0 30pF/50V/NPO 8 OUT2 OUT13 17
PWM3_G OUT3 OUT12 PWM5_B
9 16

B
PWM3_B OUT4 OUT11 PWM1_R
PWM3_R 10 15 PWM1_B
11 OUT5 OUT10 14
PWM2_B OUT6 OUT9 PWM1_G
12 13

33

33
PWM2_R OUT7 OUT8 PWM2_G

STB_3.3V LED1642GWTTR

64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
U16

VDD
VSS
PB9
PB8
BOOT0
PB7
PB6
PB5
PB4
PB3
PD2
PC12
PC11
PC10
PA15
PA14
MCU_3.3V MCU_3.3V

1 48 R395 1M
D4 R114 MCU_RST R216 1M 2 VDD PF7 47

R123

R142

R374
LL4148 27K PC13 PF6 PW_LED1
3 46 SWDIO
POWER_EN PC14/OSC32_IN PA13
4 45
LED_PW_EN PC15/OSC32_OUT PA12 PW_LED2
YI 5 44
PF0/OSC_IN PA11 Blue_LED4
R128 4.7K MCU_RST YO 6 43
PF1/OSC_OUT PA10 Blue_LED3
7 42
4.7K

10K

10K
MCU_RST R126 33
NRST PA9 IR
POWER_KEY 8 41 FB68 220
PC0 PA8 PWMCLK
C121 C182 9 40 Flash_LED4
ADC_KEY R215 1M 10 PC1 STM32F030R8T6 PC9 39 C250
2.2uF 0.1uF/16V/X7R PC2 PC8 Flash_LED3
R120 33 11 38 R122 33 FAN_PWM 100pF/50V/NP0
Close to MCU I2C_SW PC3 PC7
12 37 R118 33
VSSA PC6 BT_MFB_MCU
MCU_3.3V 13 36
14 VDDA PB15 35 R391 33 BT_RESET
BM_update_EN PA0 PB14 VALID 12

C
3.3V_D2_EN
15 34 R369 1M
16 PA1 PB13 33 R147 33
PA2 PB12 USB_EN

PB10
PB11

VDD
VSS
PC4
PC5
PA3

PA4
PA5
PA6
PA7

PB0
PB1
PB2
PF4
PF5
UART2_TX

17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
R398

R125

R390

R403
STB_3.3V

33

33

33

33

MCU_3.3V
R132 R205
4.7K 4.7K
STB_3.3V

XP9

USB_FAULT
G_INT
SPI3_LE
Relay_EN

SPI3_MISO
SPI3_MOSI
NFC_BT

SPI3_SCK
AUDIO_MUTE

CHG_EN
Y_Rest
4

I2C2_SDA
4

I2C2_SCL
SWDIO 3

D
SWCLK 2 3
1 2
1
4PIN/2.0mm R154 10K
STB_3.3V

AMP_MUTE

LED Control

E To CENTER
XP46
EEPROM STB_3.3V STB_3.3V
1 FB50 220 PWM5_G
1 2 FB51 220 PWM5_R
2 3 FB67 220 PWM5_B
3 4 FB66 220 Flash_LED3
4 R393 R394
5 FB65 220 Flash_LED4 U34 C365 1K
5 1K
6 FB64 220 PWM1_R 0.1UF
6 7 FB63 220 PWM1_G 1 8
XP36 7 2 NC VCC 7
8 FB62 220 PWM1_B NC WP
1 FB10 120/2A 8 3 6 R281 33 I2C2_SCL
1 +12V 9 FB61 220 PWM2_R NC SCL
2 9 4 5 R282 33 I2C2_SDA
2 10 FB60 220 PWM2_G GND SDA
3 10
3 C12 11 FB59 220 PWM2_B
4 11 NC/EEPROM_16Kb_M24C16
4 0.1uF/50V/X7R 12 FB58 220 LED_PW_EN
12 13 FB57 220 PWM3_R
4PIN/2.0mm 13 14 FB56 220 PWM3_G
14 15 FB55 220 PWM3_B
15 16 FB54 220 PWM4_G
16 17 FB53 220 PWM4_R
17 18 FB52 220 PWM4_B
18

18PIN/1.0mm
C304 100pF/50V/NP0
C248 100pF/50V/NP0
C247 100pF/50V/NP0
C246 100pF/50V/NP0
C245 100pF/50V/NP0
C244 100pF/50V/NP0
C243 100pF/50V/NP0
C229 100pF/50V/NP0
C231 100pF/50V/NP0
C230 100pF/50V/NP0
C232 100pF/50V/NP0
C233 100pF/50V/NP0

C277 100pF/50V/NP0
C303 100pF/50V/NP0
C257 100pF/50V/NP0
C255 100pF/50V/NP0
C256 100pF/50V/NP0
C441 100pF/50V/NP0

F XP52

1
2
1
2
3
STB_5V
FB49 220 IR
3

3PIN/2.0mm C103 C249

0.1uF 100pF/50V/NP0

GTK-XB7
29 29
GTK-XB7

4-8. SCHEMATIC DIAGRAM - MAIN Board (5/8) - • See page 44 for IC Block Diagrams.

1 2 3 4 5 6 7 8

MAIN BOARD (5/8)

A U27
1 28
LGRP MODE2
R196 0 2 27
SRC_MCLK RCKI MODE1
3 26
NC MODE0
4 25 R117 33
BT_DATA SDIN BCKO SRC_BCLK
5 24 R137 33
BT_BCLK BCKI LRCKO SRC_LRCK
To BT Board C353 C354 BT_LRCK
6
LRCKI SDOUT
23 R155 33
DATA4
10uF 0.1UF
3.3V_D1 7 22
VIO VDD 3.3V_D1
1 C328 C327 C234 C326
1 STB_3.3V 8 21
2 DGND1 DGND2
2 3 10uF 0.1UF 0.1UF 10uF
3 9 20
4 BYPAS TDMI
4 5
5 BM_D- R237 4.7K 10 19 R238 4.7K
6 3.3V_D1 IFMT0 OFMT0 3.3V_D1
6 BM_D+
7
11 18

B
7 8 R827 BT_LRCK
33 BT_LRCK 24-Bit I2S IFMT1 OFMT1 24-Bit I2S
8 9
9 12 17
10 R826 33 BT_BCLK BT_BCLK IFMT2 OWL0
10 11
11 MPEG_RST R365 1K 13 16
12 R825 33 BT_DATA BT_DATA RST OWL1
12 13 NFC_BT
13 NFC_BT C348 14 15
14 BT_RESET BT_RESET MUTE RDY TP16
14 15 0.1UF
15 16 SRC4182
16 17
17 18
18 19
19 VCC_D
20 BT_RX BT_RX
2 BT_MFB_MCU
20 VCC_D
21
21 BT_TX BT_TX S: L-->B1
22 BT_MFB 3 D2
22 23 NFC_INT BAT54C S: H-->B2
XP35 23 NFC_INT R955
24 1 BT_MFB_MPEG
45PIN/0.5MM 24 NC/10K
25 C358 C359 C360 C361 C362 C363
25 C355 U24 R228
26
26 27 1 6 47

NC/15pF/50V/NP0

NC/15pF/50V/NP0

NC/15pF/50V/NP0

NC/15pF/50V/NP0

15PF

15PF

15PF
27 DATA4 B2 S SW_G3157
28
28 29 2 5
29 30 GND VCC
30 31 3 4 C340
DATA6 C343
31 32 AD_DATA B1 A
32 33 0.1UF 10uF

C
33 74LVC1G3157GV
34
34 35
35 R909 NC/0
36
36 37
37 C306 C305 C307
38
38 0.1UF
39 0.1UF 10uF
39 40 FB37 500/800mA
40 STB_5V
41
41 42 FB38 500/800mA
42 VCC_D
43
43 44

GND
GND
44 45
45 FB69 220 POWER_KEY
POWER_KEY
FB70 220 ADC_KEY
ADC_KEY

47
46
FB71 220 Blue_LED1
Blue_LED1
FB72 220 Blue_LED2
Blue_LED2
FB73 220 Blue_LED3
Blue_LED3
FB74 220 Blue_LED4
Blue_LED4
FB75 220 PW_LED1
PW_LED1
FB76 220 PW_LED2
PW_LED2

C308 100pF/50V/NP0
C309 100pF/50V/NP0
C310 100pF/50V/NP0
C311 100pF/50V/NP0
C312 100pF/50V/NP0
C313 100pF/50V/NP0
C314 100pF/50V/NP0
C315 100pF/50V/NP0
D

GTK-XB7
30 30
 GTK-XB7

4-9. SCHEMATIC DIAGRAM - MAIN Board (6/8) -

1 2 3 4 5 6 7 8 9

MAIN BOARD (6/8)

A
Audio IN VCC_D R182 5.6Ÿ
3.3V_D1
3.3V_D1

CE22 C149
+

0.1UF
220uF/16V
C119 C172
10uF/6.3V/X5R 10uF/6.3V/X5R FB22
Audio In_L R177 20K AUX_IN_L 500/200mA R178 R181
AUX_IN_L 4.7K 4.7K

U20
R124
AUX_IN_R R9 0 1 16
10K AINR CKS0
AUX_IN_L R14 0 2 15
3 AINL CKS2 14
4 CKS1 DIF 13
5 VCOM PDN 12 AD_BCLK
AGND SCLK AD_BCLK 8
6 11 AD_MCLK

B
VA MCLK AD_MCLK 5
7 10 AD_LRCK
VD LRCK AD_LRCK 8
8 9 AD_DATA
DGND SDTO AD_DATA 6

C160 0.1UF
C186
C120 C198 ADC_AK5358A
10uF/6.3V/X5R 10uF/6.3V/X5R R38 0 C187

10uF
Audio In_R R131 20K AUX_IN_R
AUX_IN_R NC/0.1uF/25V/X5R

R119
R82 0
10K

R188 20K VOL ADJ

Audio OUT
C
A_OUT_L A_OUT_R
U928
R184 10K C133 100pF/50V/NP0 INR_OUT R890 0 R889 0
1 8
A_OUT_L1 2 LIN RIN 7 A_OUT_R1
C174 LOUT ROUT
INR- 3 6 VCC_D
10uF/6.3V/X5R VSS VDD
I2C_SDA R370 NC/33 4 5 R371 NC/33
SDA SCL I2C_SCL
R197 20K NC/PT2257 C364
C137 C321
R187 NC/10uF
470K NC/0.1uF/25V/X5R J1
NC
C51 R194 10K C135 100pF/50V/NP0 INL_OUT Audio In_L FB77 500/800mA 1
10uF/6.3V/X5R
R186 5.1K INR+ 6 WH RD
A_OUT_R1 C191 INL- R92 0
10uF/6.3V/X5R
Audio In_R FB78 500/800mA 2
C60 Audio Out_L FB79 500/800mA 3
10uF/6.3V/X5R
R193 5.1K INL+
A_OUT_L1 3.3V_D1 5
WH RD
U927 R189
Audio Out_R FB80 500/800mA 4
INR+ 1 14 INL+ 100K
R190 C134 RINP LINP C61
NC 470K

1
INR- 2 13 INL- R381 10uF/6.3V/X5R ESD3 ESD4 ESD5 ESD6 RCA/4h
RINN LINN INR_OUT R87 0 Audio Out_R

NC/LVSL10180Z020/18V/2pF

NC/LVSL10180Z020/18V/2pF

NC/LVSL10180Z020/18V/2pF

NC/LVSL10180Z020/18V/2pF
1.5K C197C171
INR_OUT 3 12 INL_OUT
OUTR OUTL

1000pF/50V/X7R

1000pF/50V/X7R
4 11 R195 30K R48 1K C62

D
SGND UVP 10uF/6.3V/X5R
INL_OUT R88 0 Audio Out_L

2
AUDIO_MUTE R183 470 5 10 3.3V_D1
7 MUTE# PGND
6 9 R85 0
PVSS PVDD R332
CE13 R192
7 8 C116 C173 + 100K NC/6.8K
R180 C117 CN CP
C145
47K 0.1UF

10uF/6.3V/X5R

NC/100uF/16V/SMD
0.1UF 1uF AS9632

C136 1uF

STB_3.3V R344 10K

VCC_D

Party_Chain_In

Party Chain VCC_D V_12V VCC_4052

E
R47 0
Vref
R303
10K R364 R233 R360
NC/10K R83 0 1K 100K
R343
R301 10K Q762 VCC_4052
10K

R404 1M

R405 1M

R406 1M

R407 1M
PNP_3CG3906M
S0: L-->nY0 R224 100 Vref
R342 10K Q763
Party_Chain_Out
R86 10K Q22 R312 22K
PNP_3CG3906M
S0: H-->nY1
NPN_3DG3904M R227 R361 C185
C184 + CE10
R340 82K Q23 RTL R15 0.1UF 100uF/16V/SMD 1K 100K 1uF
U25
R84 NPN_3DG3904M 20K
C175 R314 Audio In_R C93 10uF/6.3V/X5R C86 10uF/6.3V/X5R 12 16
10K R313 R345 C87 10uF/6.3V/X5R 14 X0 VCC
15K 6.8K C177 C178 AOUT_R X1
2.2uF R341 22K 15 C83
2.2uF 10uF R24 10K X2
68K 11 10uF/6.3V/X5R
R17 X3
Audio Out_R 13
R347 10K Q24 20K X A_OUT_R
Audio In_L C94 10uF/6.3V/X5R C89 10uF/6.3V/X5R 1
NPN_3DG3904M C91 10uF/6.3V/X5R 5 Y0
AOUT_L 2 Y1
R26 10K Y2 C85
R346 C179 R348 4
22K Y3 10uF/6.3V/X5R
Audio In_R R315 56K 10uF 10K 3
Y A_OUT_L
R209 33 10
R338 68K 7 Party_Chain_SW A
9
R337 C176 B
680K 10PF/50V/NPO 6
R339 R222 EN
RTL 470K
7 8
4.7K VEE GND
74HC4052
R353 82K Q25
NPN_3DG3904M
3.3V_D1

F
R354 C181
68K 2.2uF

Audio In_L R349 56K

R351 68K

R350 C180
R352 680K 10PF/50V/NPO
470K

GTK-XB7
31 31
GTK-XB7

4-10. SCHEMATIC DIAGRAM - MAIN Board (7/8) - • See page 44 for IC Block Diagrams.

1 2 3 4 5 6 7

MAIN BOARD (7/8)

1.8V
3.3V

3.3V_D1 1.8V_D

A
C208 C140 C142 C204 C205 C141 C147
0.1UF 0.1UF 10uF/6.3V/X5R 0.1UF 0.1UF 0.1UF 10uF/6.3V/X5R

Y_BCLK_OUT 11
C202
NC/12PF 1.8V 3.3V

R412

R256
B

NC/47K
0

24

23

22

21

20

19

18

17
R230 33 Y_DATA_IN
5 I2S_DATA_OUT
SRC_LRCK R261 33 Y_LRCLK_IN

OPEN2

GPIO11

DVDD18_1

IRQ_N

OPEN1
Y_BCLK_IN

DVSS3

TESTb

DVSS2
SRC_BCLK R262 33

C148 C150 C151

NC/12PF

NC/12PF

NC/12PF
R284 NC/33
I2C_SDA
R285 NC/33
I2C_SCL
25
DVSS4 16 33
R377 I2C2_SDA
R392 0 26 SDA
11 Y_LRCLK_OUT GPIO10 15 R376 33
SCL I2C2_SCL
R387 0 27
11 Y_DATA_OUT
28
GPIO9
U13 IOVDD1
14
TP61 TP64
3.3V
TP65 GPIO8
29 YSS952 XOUT
13 R260 1.5K

C
3.3V IOVDD2 12
R413 0 30 XIN
11 Y_MCLK GPIO7 R275
11
31 PLLVSS2 3.3V 1M
C199C200C201 1.8V DVDD18_2 10 Y2
PLLVSS1 R231 NC/47K
32
GPIO6

NC/12PF

NC/12PF

NC/12PF
9 R279 100
IC_N Y_Rest 7
24.576MHz±30ppm
C153 C154
33 30pF/50V/NPO
GNDP R283 39pF/50V/NP0
10K

PLLVDD
DVSS1
GPIO5

GPIO4

GPIO3

GPIO2

GPIO1

GPIO0
1

8
D

Y_LRCLK_IN
Y_DATA_IN

Y_BCLK_IN
1.8V

AMP_3.3V

U17
TGND

3.3V_D1 AMP_3.3V 1 56 C211 C212 C227

2 PWM_HPM_L PWM_P_6 55
R308 4.7
3 PWM_HPP_L PWM_M_6 54 0.1UF 0.1UF 10uF/6.3V/X5R
FB28 500/800mA PWM_HPM_R PWM_P_5
C214 4700pF 4 53
5 PWM_HPP_R PWM_M_5 52 C215 0.1UF
+ CE23 R291 470 0.047uF/50V/X7R 470 C218 0.047uF/50V/X7R 6 AVSS VR_PWM 51
C216 C217 R297 GND
100uF/16V/SMD AMP_3.3V 7 PLL_FLTM AVSS_PWM 50
0.1UF

E
C219 4700pF 8 PLL_FLTP AVDD_PWM 49
R290 2.2 9 VR_ANA PWM_P_8 48
10 AVDD PWM_M_8 47
GND R292 0
C223 11 ASEL_VACS2 PWM_P_7 46
C224 10 Y_MCLK MCLK PWM_M_7
R294 12K/1% R299 6.2K/1% 12 45
10uF/6.3V/X5R 0.1UF 13 OSC_RES PWM_P_4 44
GND DVSS2_CORE PWM_M_4
14 43
AMP_3.3V AMP_3.3V DVDD2_CORE PWM_P_3
R267 0 15 42
TP53 EMO_1 PWM_M_3
AMP_RST 16 41 R295 33
RESET PWM_P_2 OUT2A 12
TGND HP_SEL 17 40 R300 33
T_PDN 18 HP_SLE
PDN
PWM_M_2
PWM_P_1
39 R304 33
OUT2B
OUT1A
12 OUT2A/B : L
19 38 12
7 AMP_MUTE
5 DSP_SDA TP55 20 MUTE PWM_M_1 37
R305
R289
33
2.2K
OUT1B 12 OUT1A/B : R
R288 R287 R268 SDA VALID VALID 12
5 DSP_SCL TP57 21 36
4.7K 4.7K 4.7K SCL DVSS1_CORE
R306 33 T_LRCLK 22 35
10 Y_LRCLK_OUT LRCLK DVDD1_CORE AMP_3.3V
R307 33 T_SCLK 23 34 R309 33 AMP_FAULT 5,12
10 Y_BCLK_OUT R302 33 T_SDIN1 24 SCLK BKND_ERR 33
HP_SEL 10 Y_DATA_OUT SDIN1 PSVC TP54
R310 10K 25 32 GND
26 SDIN2 TEST 31
T_PDN R311 10K R286
27 SDIN3 LRCLKO 30
SDIN4 SCLKO 4.7K
28 29
5 AMP_RST VR_DIG SDOUT
AMP_RESET

F
GND C225 AMP_3.3V
R293 C226
C324 TAS5534
0.1UF 100K 0.1UF 10uF/6.3V/X5R

GND

GTK-XB7
32 32
 GTK-XB7

4-11. SCHEMATIC DIAGRAM - MAIN Board (8/8) - • See page 44 for IC Block Diagrams.

1 2 3 4 5 6 7 8 9

MAIN BOARD (8/8) C263 + CE25

AMP_36V

A
R333
0.1uF 820uF/50V 5.6Ÿ

V_12V C316 L+ R773 220K

330pF/50V
R316 3.3
R775 C530
L485 220K 10uF
U18 10uH/12A
C264 0.1uF 1 44 C265 0.033uF/50V/X7R L+ L- R774 220K
C266 GVDD_AB BST_A
10UF C267 0.1uF 2 43 C268 0.033uF/50V/X7R
VDD BST_B C271
R317 24K 3 42 R366
OC_ADJ GND 5.6Ÿ C1750 C1754 0.01uF/50V/X7R C269
C270
4 41 R319 Q756 Q757
11 VALID /RESET GND 1ȝF 1ȝF 1000pF/50V/X7R 0.1uF PNP_3CG3906M PNP_3CG3906M
NC/5.6Ÿ
5 40 C272
11 OUT2A INPUT_A OUT_A C317 C276
C275 R318
270pF/50V/X7R C322 1uF/63V R320
6 39 3.3
11 OUT2B 270pF/50V/X7R

NC/0.01uF/50V/X7R
INPUT_B OUT_A 3.3 R+ R776 220K

NC/0.01uF/50V/X7R
C273 0.1uF 7 38 C274 C280
C_START PVDD_AB C298 C1751 C1755 C281 C283
NC/100pF/50V/NP0 R778

1000pF/50V/X7R
1000pF/50V/X7R 0.1uF C531

0.1uF
C332 1uF DVDD_M21 8 37
DVDD PVDD_AB R368 1ȝF 1ȝF C279 220K 10uF

B 9 36 5.6Ÿ R- R777 220K

0.01uF/50V/X7R
GND PVDD_AB L486
10uH/12A
10 35 L-
GND OUT_B
11 34
GND GND
12 33 Q758 Q759
GND GND L487 PNP_3CG3906M PNP_3CG3906M
10uH/12A
C333 1uF 13 32 R+
AVDD OUT_C
14 31 R782
11 OUT1A INPUT_C PVDD_CD C335
R367 100
15 30 C285 C292
11 OUT1B INPUT_D PVDD_CD 5.6Ÿ C1752 C1757 0.01uF/50V/X7R
1000pF/50V/X7R 0.1uF
16 29 C288 C286 R326
5,11 AMP_FAULT /FAULT PVDD_CD 1ȝF 1ȝF
NC/5.6Ÿ C287
17 28 R327

1000pF/50V/X7R
R328 NC/0 C289

0.1uF
/OTW OUT_D C320 3.3 C290
270pF/50V/X7R C329 R325

NC/0.01uF/50V/X7R
R329 NC/0 18 27 1uF/63V
/CLIP OUT_D 270pF/50V/X7R 3.3 R783 C769

NC/0.01uF/50V/X7R
C299 100K 0.22uF
19 26 C291 C293
M1 GND NC/100pF/50V/NP0 C1753 C1756
0.1uF
DVDD_M21 R330 NC/47 20 25 1000pF/50V/X7R
1ȝF 1ȝF C334 AMP_FAULT
M2 GND R372
Q21
5.6Ÿ

0.01uF/50V/X7R
V_12V 21 24 C295 0.033uF/50V/X7R L488 NPN_3DG3904M
M3 BST_C

C R331 10uH/12A
R334 3.3 22 23 C297 0.033uF/50V/X7R R-
0 GVDD_CD BST_D

C296
DC detect
0.1uF TAS5624A

3.3V_D1

36V_MAIN R362 0

C188 C50 C161

R321 NC/100K 0.1UF
0.1UF

10uF/6.3V/X5R
16
15
14
U35 R136
Q19
NC/LL4148 NC/PNP_3CG9012M 4.7K
D8

NC5
NC4
VDD
1 13
VDD_IO NC3

D
2 12 XP21
3 NC1 GND2 11
NC2 INT G_INT L+ 1
R323 NC/10K VALID 11,12 R232 100 4 10 1
5 I2C_SCL SCL RES3 L- 2 L 3Ÿ

ADDR
5 9 2

RES1
GND1 RES2

SDA
+ CE6 2PIN_3.96mm
R322 NC/10K Q20
NC/100uF/50V NC/NPN_3DG3904M KXCJK-1013

6
7
8
C282 R324 R265 100
5 I2C_SDA
NC/0.1UF NC/10K R363 10K
G-Sensor RW+ 1
XP22

R+ 2 1 RW 6Ÿ
R- 3 2 R 3Ÿ
3
C775 3PIN_3.96mm
Power OFF Mute Circuit
NC/0.01uF/50V/X7R

SW6
XP10
S2 1
4 S1 1
4 RW+ 2
C770 1000pF/50V/X7R S1 3 2
RW+ 4 3
1 R- 4

E
1
C771 1000pF/50V/X7R 4PIN/2.5mm
3 S2
3
C772 1000pF/50V/X7R
5 2
FAN CONTROL C773
5 2

C774
V_12V

0.01uF/50V/X7R

0.01uF/50V/X7R
V_12V G5LE-1

Q253 XP14
FB25 500/800mA PNP_MMBT8550C VCC_FAN 1
2 1 D7 MBRX180/80V/1A
2
R356
R298 4.7K R355 100K 4.7K 2PIN/2.0mm
C302
4.7uF
Q255 Q254 C301
PNP_3CG3906M NPN_3DG3904M Vfb 4.7uF
Vb R359
1.2K

R77 10K Q6
Relay_EN NPN_3DG3904M
R358 10K
FAN_PWM

F R357 100K
C300
1UF/16V/X7R
R60
47K
C323
0.1UF

GTK-XB7
33 33
 GTK-XB7

4-12. PRINTED WIRING BOARD - BT&NFC Board -
• See page 24 for Circuit Boards Location.
• : Uses unleaded solder.
1 2
BT&NFC BOARD (COMPONENT SIDE)
4-13. SCHEMATIC DIAGRAM - BT&NFC Board -
1 2 3 4 5 6 7 8 9
3 4 5
BT&NFC BOARD BUILT-IN BLUETOOTH MODULE ANTENNA SECTION
A BT U12

51
50
49
BT_BM63

A P20 TM11

ANT3
ANT2
ANT1
BAT_IN TM12
1 48
BT_LRCK1 R103 33 2 DR0 GND 47 EAN TM13
BT_BCLK1
BT_DATA1
R108 33 3
4
RFS0
SCLK0
P05
P30
46
45 ADAP_IN
Apple Authentication
R110 33 TM14
5 DT0 P27 44 P20
BT_3.3V AOHPR P20
C108 C110 C107 6 43 BT_RX1 TM16 Active Mode Current : 7.5mA
AOHPM P02

R225

R226
7 42
AOHPL P31

NC/15pF/50V/NP0

NC/15pF/50V/NP0

NC/15pF/50V/NP0
8 41 BT_TX1 TM15
9 MICN1 P33 40 BT_3.3V CP3V3
MICP1 P36

2.2K

NC/2.2K
10 39 BM_D+_1 TM19 R109 NC/0
11 MICBIAS DP 38 BM_D-_1
R270 12 AIR DM 37 EAN P24 TM20 BT_VDDIO R111
NC/100K 0 C106 C116
CP_SCL 13 AIL EAN 36 TM17
P12 P03 10uF 0.1UF
CP_SDA 14 35 TM18
BT_RESET1R273 1K 15 P13 P00 34
B P24
16
17
RST_N
P01
P24
P35
P37
GND
33
32
CP_Reset

18 31 CP3V3

B
NFC_BT1

CODEC_VO
19 P04 LED1 30

SYS_PWR
C111

AMB_DET
HCI_RXD
C124

ADAP_IN
HCI_TXD
P15 LED2 U15 0.1UF

VDD_IO

BAT_IN
NC/0.1uF/25V/X5R
1 8

LED3
PWR
GND VCC
CP_SDA R220 33 2 7 R375 0 CP_Reset
SDA RST

20
21
22
23
24
25
26
27
28
29
R223
BT&NFC BOARD (CONDUCTOR SIDE)
3 6 33 CP_SCL
NC SCL
4 5
U26 MFB1 NC NC 9 R378
GND

BT_VDDIO
BT_3.3V NC/0

ADAP_IN
BT_RX1
BT_RESET1 R368 0 2

BT_TX1
RST 3 BAT_IN BAT_IN L3 120/2A
1 VCC AUTHENTICATION IC 2.0C
GND

C SGM803
C105 C104 C115 CE18
+

100pF/50V/NP0
0.1UF

NC/10UF/6.3V/X5R
220uF/16V

C
D
TP63 NFC BT_3.3V

R106
U7 100K

9
1 8

GND
VB VDDA
NFC_INT1
C2 C18 2 7
NC NC TP56
PCB LAYOUT ANTENNA 3 6

120pF/50V/NP0

20pF/50V/NP0
VSS NC C69
4 5
VA NIRQ 1uF R141 0 NFC R105 100K Q9
NPN_3DG3904M

D
MN63Y1212 C290 R229
R143 0 100pF/50V/NP0 1M
TP62

NFC CIRCUIT REFERENCE 40GKB630U-NFC2G

C336 C337

47
46
10uF 0.1UF
45

GND
GND
45 BT_3.3V
To Main Board 44
44 43
43 42

E
42 41 BM_D-_1
41 40 BM_D+_1
40 39
39 38 BT_LRCK1
38 37
37 36 BT_BCLK1
36 35
35 34 BT_DATA1
34 33 NFC_BT1
33 32 BT_RESET1
32 31
31 30
30 29
29 28
28 27
27 26 BT_RX1
26 25 BT_TX1
XP34 25 24 MFB1
45PIN/0.5mm 24 23 NFC_INT1
To Key Board 23 22
22 21
21 C353 C338 C350 C351 C352 C354
20
20

NC/15pF/50V/NP0

NC/15pF/50V/NP0

NC/15pF/50V/NP0

NC/15pF/50V/NP0

NC/15pF/50V/NP0

NC/15pF/50V/NP0
1 19
1 2 19 18
2 3 18 17
3 4 17 16
4 5 16 15
5 6 15 14
6 7 R917 0 14 13
7 8 R918 0 13 12

F
XP8 8 12
16pin/1.0 9 11
9 10 R919 0 11 10
10 11 R920 0 10 9
11 12 R921 0 9 8
12 13 R922 0 8 7
13 14 R923 0 7 6
14 15 R924 0 6 5
GND
GND

15 16 5 4
16 4 3
3 C355 C356 C357 C358 C359 C360 C361 C362
2
2
18
17

15pF/50V/NP0

15pF/50V/NP0

15pF/50V/NP0

15pF/50V/NP0

15pF/50V/NP0

15pF/50V/NP0

15pF/50V/NP0

15pF/50V/NP0
1
1

GTK-XB7
34 34
 GTK-XB7

4-14. PRINTED WIRING BOARD - USB + KEY Board - • See page 24 for Circuit Boards Location. 4-16. PRINTED WIRING BOARD - IR Board - • See page 24 for Circuit Boards Location.

• : Uses unleaded solder. • : Uses unleaded solder.

1 2 3 4 1 2
USB + KEY BOARD (COMPONENT SIDE) USB + KEY BOARD (CONDUCTOR SIDE)
IR BOARD IR BOARD
(COMPONENT SIDE) (CONDUCTOR SIDE)
A

4-15. SCHEMATIC DIAGRAM - USB + KEY Board - 4-17. SCHEMATIC DIAGRAM - IR Board -

1 2 3 4 5 1 2 3

USB + KEY BOARD USB_5V

IR BOARD
A USB FB39
500/800mA A XS13
1
1
STB_5V_1
6

P1 2
2 3 IR_1
XS15
Shell A Shell B

1 1 3
VCC 2 DN 2 1 3PIN/2.0mm/180mm C24
D- 3 DP 3 2 0.1UF
D+ 4 4 3
GND 4
ESD2 ESD3 C1 C2 4PIN/2.0mm/200mm
EGA10603V05A1-B

EGA10603V05A1-B

4Pin/2mm
5

0.1uF

10uF

XS1
1
2 1
ADC_KEY1 2
R45 0 3
Blue_LED5 3
4
Blue_LED6 4
5
Blue_LED7 5
6
C316 47pF/50V/NP0
C317 47pF/50V/NP0
C318 47pF/50V/NP0
C319 47pF/50V/NP0

6
6PIN/2.0mm/120mm

B B
STB_5V_1
IR

R29 R19
100 4.7K

IR1
SW6 2.2V 1 R22 1K IR_1
ADC_KEY1 R39 20K IR 2

1
GND ESD4
ADD SPK 3

NC/LVSL10180Z020/18V/2pF
VCC 4 C9 C12
+ CE3
C320 47pF/50V/NP0

ESD7 GND 5
GND 47uF/10V

NC/47pF/50V/NP0
SW7

0.1UF
2.72V
NC/EGA10603V05A1-B

R40 47K
IRR_5P
PARTY CHAIN

2
C
C

USB_5V USB_5V USB_5V

R458 R459 R460

220 220 220

L LED8
LED_GREEN R LED9
LED_GREEN Mold parts LED10
LED_GREEN

D Blue_LED5 R25 4.7K Q15 Blue_LED6 R43 4.7K Q16 Blue_LED7 R46 4.7K Q17
NPN_3DG3904M NPN_3DG3904M NPN_3DG3904M
C10 C11 C13
R41 R42 R44
0.1uF

0.1uF

0.1uF

10K 10K 10K

GTK-XB7
35 35
GTK-XB7

4-18. PRINTED WIRING BOARD - CONTROL Board - • See page 24 for Circuit Boards Location. • : Uses unleaded solder.

1 2 3 4 5 6 7 8 9 10
CONTROL BOARD (COMPONENT SIDE)

CONTROL BOARD (CONDUCTOR SIDE)

GTK-XB7
36 36
 GTK-XB7

4-19. SCHEMATIC DIAGRAM - CONTROL Board -

1 2 3 4 5 6 7 8 9

CONTROL BOARD
A
To Main Board KEY
C307 C306
XP16 0.1uF 0.1uF
1 FB40 500/800mA
1 STB_5V
2
2 3 SW3 0V SW5 0V
3 ADC_KEY R38 100 POWER_KEY R37 100
4
4 5
5 Mega Bass Power
6 ESD6 C22 ESD5 C21
6 7 R815 POWER_KEY
0

NC/EGA10603V05A1-B

NC/EGA10603V05A1-B
7 8 R816 ADC_KEY
0
8 SW2 1.0V SW4 1.0V

47pF/50V/NP0

47pF/50V/NP0
9 R23 4.7K R20 4.7K
9 10 R809 Blue_LED1
0
10 11 R810 Blue_LED2
0 VOL+ Function
11

B
12 R811 0 Blue_LED3
12 13 R812 Blue_LED4
0
13 14 R813 PW_LED1
0
14 15 R814 PW_LED2 SW1 1.65V
0 R36 10K
15 16
16

C308 47pF/50V/NP0
C309 47pF/50V/NP0
C310 47pF/50V/NP0
C311 47pF/50V/NP0
C312 47pF/50V/NP0
C313 47pF/50V/NP0
C314 47pF/50V/NP0
C315 47pF/50V/NP0
VOL-
16PIN/1.0mm

C
STB_5V LED STB_5V STB_5V STB_5V STB_5V

R452 R453 R454 R455

470 1K 1K 220
R457 R456
220 220

BT LED4
LED_BULE USB
LED5
LED_WHITE AUX
LED6
LED_WHITE MEGA BASS LED7
LED_RED
PW_LED1 R28 4.7K Q13 Q14 R31 4.7K PW_LED2
NPN_3DG3904M

NPN_3DG3904M

C7 C8

D
R30 R32
Blue_LED1 R19 4.7K Q9 Blue_LED2 R21 4.7K Q10 Blue_LED3 R24 4.7K Q11 Blue_LED4 R26 4.7K Q12
0.1uF

0.1uF

10K 10K
NPN_3DG3904M NPN_3DG3904M NPN_3DG3904M NPN_3DG3904M
C3 C4 C5 C6
R35 R34 R33 R27
0.1uF

0.1uF

0.1uF

0.1uF
10K 10K 10K 10K
3

LED1
PIN-1 GREEN
POWER PIN-3 RED
LED_3P_2PARTA
2

E
STB_5V STB_5V

R1 0

R2 0

R3 0

GTK-XB7
37 37
 GTK-XB7

4-20. PRINTED WIRING BOARD - LA Board - • See page 24 for Circuit Boards Location. • : Uses unleaded solder. 4-21. PRINTED WIRING BOARD - RGBE Board -
1 2 3 4 5 6 7 8 9 • See page 24 for Circuit Boards Location.

• : Uses unleaded solder.

A 1 2
RGBE BOARD RGBE BOARD
(COMPONENT SIDE) (CONDUCTOR SIDE)
LA BOARD (COMPONENT SIDE)

B
A

LA BOARD (CONDUCTOR SIDE)

D

GTK-XB7
38 38
 GTK-XB7

4-22. SCHEMATIC DIAGRAM - LA Board - 4-23. SCHEMATIC DIAGRAM - RGBE Board -

1 2 3 4 5 6 7 8 9 1 2 3

LA BOARD RGBE BOARD

A A To CENTER

XS14
1
C414
10uF
C14
0.1uF

1 5V_D2_2
2
2 3 R864 0 PWM5_R_2
To Mainboard 3 4 R865 0 PWM5_G_2
XS1 4 5 R866 0 PWM5_B_2
5
1
1 +12V_1 5PIN/2.0mm/40mm
2 C15C16C17
2 3
3 4

47pF/50V/NP0
47pF/50V/NP0
47pF/50V/NP0
4 C20
0.1uF/50V/X7R
4PIN/2.0mm/160mm

To Mainboard

XP38 UPPER RIGHT CORNER RGB A UPPER LEFT CORNER RGB B UPPER CENTER FLASH LED A
18 R804 0 PWM5_G_1
18 17 R805 0 PWM5_R_1
17 16 R806 0 PWM5_B_1

B B
16 15 R828 0 Flash_LED3_1
15 14 R829 0 Flash_LED4_1
14 13 R791 0 PWM1_R_1
13 12 R792 0 PWM1_G_1
12 11 R793 0 PWM1_B_1
11 10 R797 0 PWM2_R_1
10 5V_D2_1 FB30 120/2A
9 R798 0 PWM2_G_1 LED_POWER4
9 5V_D2_1 FB23 120/2A LED_POWER1
8 R799 0 PWM2_B_1 5V_D2_1 FB29 120/2A
8 LED_POWER3
7 R885 0 LED_PW_EN_1 C476
7 6 R897 0 PWM3_R_1 0.1UF C473
6 C475
5 R898 0 PWM3_G_1 0.1UF 0.1UF
5 4 R899 0 PWM3_B_1 FB23 120/2A
4 5V_D2_2 LED_POWER1
3 R900 0 PWM4_G_1
3 2 R901 0 PWM4_R_1
2 1 R902 0 PWM4_B_1 C26
1 0.1uF

18PIN/1.0mm
C259 100pF/50V/NP0

C250 100pF/50V/NP0

C367 100pF/50V/NP0

C322 100pF/50V/NP0
C258 100pF/50V/NP0
C252 100pF/50V/NP0
C251 100pF/50V/NP0

C249 100pF/50V/NP0
C236 100pF/50V/NP0
C239 100pF/50V/NP0
C237 100pF/50V/NP0
C238 100pF/50V/NP0

C366 100pF/50V/NP0

C346 100pF/50V/NP0
C287 100pF/50V/NP0
C260 100pF/50V/NP0
C320 100pF/50V/NP0
C442 100pF/50V/NP0

C LED_POWER3

R517
LED_POWER4
C
R514
4.7K
4.7K

PWM2_B_1 Q35 LED_POWER1

PWM1_B_1 Q32 PNP_MMBT8550C LED_POWER1
PNP_MMBT8550C
C479 C482

1
R463

R453
0.1UF 0.1UF
LED2
R518
R515
4.7K
C92 0.01uF/50V/X7R 4.7K

22ohm
NC/22ohm

4
PWM2_G_1 Q36
5V_D2_1 PWM1_G_1 Q33 PNP_MMBT8550C GREEN BLUE RED
U21 PNP_MMBT8550C
AS5430A
+12V_1 C483
3 L13 10uH/3A C480 LED4
SW 0.1UF
1 0.1UF LED_White_2835
BS R519
R516
FB33 120/2A 2 5 4.7K
IN FB R18 4.7K
47K/1%

D D
PWM2_R_1 Q37
C15 C117 PWM1_R_1 Q34 PNP_MMBT8550C R47
CE13 C191 PNP_MMBT8550C 4.7K
+ 7 6 C484
GND

EN COMP C481 Flash_LED3_1 R504 470 Q27

SS

0.1uF/16V/X7R
TP
100uF/16V

0.1uF 10uF 0.1UF S8050M-C PWM5_G_2 Q18

CE20 0.1UF
C156 + PNP_3CG3906M
R85 C485
8

R512

R536

R456

R465

R455

R466
3900pF/50V/X7R 0.1UF C28
13K/1%
470uF/10V

0.1uF R531 R503

R513

R537

R458

R468

R457

R467
R87 R381 C192 R384
0.1uF C193
NC/22ohm

22ohm

100

22ohm

NC/22ohm

22ohm
1K 47K 6.8K

NC/100
0.1uF R48
100 4.7K

NC/22ohm

22ohm

100

22ohm

NC/22ohm

22ohm
LED_PW_EN_1
PWM5_B_2 Q19
PNP_3CG3906M
VOUT=0.925*(47+13)/13=4.27V C29
0.1uF R530 R505

3
R49
1

NC/200Ÿ
R G B LED6 200Ÿ 4.7K
R G B LED3
0
0

E
PWM5_R_2 Q26

6
E
PNP_3CG3906M
4

C30 R532 R506

0.1uF

NC/150
150
To LED B
C411 R913 0 5V_D2_1
XS2 0.1uF/50V/X7R
1
1 2
2 3
3 4
4 R914 0
C412 5V_D2_1
4PIN/2.0mm/160mm
100pF/50V/NP0

To LED B
XP55
10PIN/1.25mm
1 R908 500/200mA PWM4_B_1
1 2 R907 500/200mA PWM4_R_1
2 3 R906 500/200mA PWM4_G_1
3 4 R857 500/200mA Flash_LED4_1
4 5 R859 500/200mA PWM5_B_1
5 6 R858 500/200mA PWM5_R_1
6 To RGB E C393 C394
7 R860 500/200mA PWM5_G_1
7 0.1UF 10uF
8 R862 500/200mA PWM3_B_1 XP54
8 9 R861 500/200mA PWM3_G_1

F
GND
GND

9 1
10 R863 500/200mA PWM3_R_1 1 5V_D2_1
10 2
2 3 R851 0 PWM5_R_1
3 4 R852 0 PWM5_G_1
12
11

C443 100pF/50V/NP0
C444 100pF/50V/NP0
C445 100pF/50V/NP0

C405 100pF/50V/NP0
C407 100pF/50V/NP0
C408 100pF/50V/NP0
C409 100pF/50V/NP0
C410 100pF/50V/NP0
C406 100pF/50V/NP0
C404 100pF/50V/NP0

4 5 R853 0 PWM5_B_1
5
C395 100pF/50V/NP0
C397 100pF/50V/NP0
C396 100pF/50V/NP0

5PIN/2.0mm

GTK-XB7
39 39
 GTK-XB7

4-24. PRINTED WIRING BOARD - LB Board - • See page 24 for Circuit Boards Location. • : Uses unleaded solder. 4-25. PRINTED WIRING BOARD - RGBF Board -
1 2 3 4 5 6 7 8 9 • See page 24 for Circuit Boards Location.
LB BOARD (COMPONENT SIDE) • : Uses unleaded solder.

A 1 2
RGBF BOARD RGBF BOARD
(COMPONENT SIDE) (CONDUCTOR SIDE)

B
A

E LB BOARD (CONDUCTOR SIDE)

GTK-XB7
40 40
 GTK-XB7

4-26. SCHEMATIC DIAGRAM - LB Board - 4-27. SCHEMATIC DIAGRAM - RGBF Board -

1 2 3 4 5 6 7 8 9 1 2 3

LB BOARD RGBF BOARD

A A To RGB D

XS12
1
C415
10uF
C18
0.1uF

5V_D3_3
LOWER LEFT CORNER RGB D LOWER RIGHT CORNER RGB C LOWER CENTER FLASH LED B 1
2
2
3 R867 0 PWM5_R_3
3 4 R868 0 PWM5_G_3
4 5 R869 0 PWM5_B_3
5
5PIN/2.0mm/40mm C19C20C23

47pF/50V/NP0
47pF/50V/NP0
47pF/50V/NP0
5V_D3_1 FB31 120/2A FB32 120/2A
LED_POWER5 5V_D3_1 LED_POWER6
FB24 120/2A
5V_D3_1 LED_POWER2
C477 C478
0.1UF 0.1UF C474
0.1UF

B To LEDA
B 5V_D3_3 FB24 120/2A LED_POWER2
C380 R915 0
0.1uF/50V/X7R 5V_D3_1 C27
XP37 LED_POWER5
1 0.1uF
1 LED_POWER6
2 R520
2 3
3 4.7K
4 R524
4 R916 0 4.7K
C371 5V_D3_1
4PIN/2.0mm PWM3_B_2 Q38
100pF/50V/NP0 PNP_MMBT8550C
PWM4_B_2 Q41 LED_POWER2
C486 PNP_MMBT8550C
0.1UF
To LED A C489
0.1UF
XP56 R521

R464

R454
10PIN/1.25mm 4.7K
R525
1 R905 0 PWM4_B_2 4.7K
1 2 R904 0 PWM4_R_2 PWM3_G_2 Q39
2 3 R903 0 PWM4_G_2 PNP_MMBT8550C
PWM4_G_2

NC/22ohm

22ohm
3 Q42 LED_POWER2
4 R837 0 Flash_LED4_2 PNP_MMBT8550C
4 C487
5 R838 0 PWM5_B_2
5 0.1UF
6 R839 0 PWM5_R_2

C C

1
6 C490
7 R840 0 PWM5_G_2 R522
7 0.1UF LED3
8 R841 0 PWM3_B_2 4.7K LED5
8 9 R842 0 PWM3_G_2 R526 LED_White_2835
GND
GND

9 10 R843 0 PWM3_R_2 4.7K

10 PWM3_R_2 Q40
PNP_MMBT8550C
PWM4_R_2 Q43

4
12
11

C370 100pF/50V/NP0
C369 100pF/50V/NP0
C368 100pF/50V/NP0

C261 100pF/50V/NP0
C262 100pF/50V/NP0
C276 100pF/50V/NP0
C378 100pF/50V/NP0
C379 100pF/50V/NP0
C377 100pF/50V/NP0
C376 100pF/50V/NP0

C488 PNP_MMBT8550C GREEN BLUE RED

0.1UF
C491
0.1UF
Flash_LED4_2 R510 470 Q31
S8050M-C
C492

R523

R538

R460

R470

R459

R469

R527

R539

R462

R472

R461

R471
0.1UF
R50
4.7K

NC/22ohm

22ohm

100

22ohm

NC/22ohm

22ohm

NC/22ohm

22ohm

100

22ohm

NC/22ohm

22ohm
PWM5_G_3 Q21
PNP_3CG3906M

C31
0.1uF
R535 R504

D D

NC/100
1

3
R G B LED7 100
0 LED8 R51
R G B 4.7K
0

6
PWM5_B_3 Q20

6
PNP_3CG3906M

C32
0.1uF
R534 R507

To RGB F

NC/200Ÿ
C415 C414
0.1UF 10uF 200Ÿ
XP50 R52
1 4.7K
1 5V_D3_1
2
2 3 R864 0 PWM5_R_2
3 4 R865 0 PWM5_G_2
4 PWM5_R_3 Q27
5 R866 0 PWM5_B_2 PNP_3CG3906M
5
C418 100pF/50V/NP0
C417 100pF/50V/NP0
C416 100pF/50V/NP0

E
5PIN/2.0mm C33
0.1uF R533 R508

NC/150
150

GTK-XB7
41 41
GTK-XB7

4-28. PRINTED WIRING BOARD - PSU Board - • See page 24 for Circuit Boards Location. • : Uses unleaded solder.

1 2 3 4 5 6 7 8 9 10
PSU BOARD (COMPONENT SIDE) PSU BOARD (CONDUCTOR SIDE)

GTK-XB7
42 42
 GTK-XB7

4-29. SCHEMATIC DIAGRAM - PSU Board -

1 2 3 4 5 6 7 8 9

PSU BOARD T501

D542

R510
HER203G/2A/200V

NC/2.2/2W

A
PQ3230 C510
R514 NC/18.2/2W
R5101 9.1 2200pF/400V
HV 1 8
R509 VDD A8 9 R5102 NC/19.1
A9 1
CN503 Alternative JP508
R519 XP1
NC CE5032
CE503 C509 2 V1 M36V 36V PCON 1 1:PSon
R580 1
RV502 NC 0 M-GND 2 2:M-GND
22K 103/400V 2 T501_S3 3 M36V M36V 3 2
+ + 3:M36V
R508 C523 N.C NC 4 3
4 4:+36V
150uF/450V NC D515 SF20A300HPI/20A/300V LIF551 36V 5 5:+36V
6 5
110VAC-127VAC\ 1
2
NC JP515 103/400V C553 R577 6:+36V
R523 1 C562 C558 7 6
NC/0 7:GND
220VAC-240VAC 7
1
2
NC R585 R552 R555 R550 R551 C557 GND 8
8 8:GND
Voltage Selector SW2 T501_P1 3
D
D516 2 9
9 9:GND
JP507 NC/SF20A300HPI/20A/300V CE506 CE507 + 0.1uF/50VNC
33K 10 3 + C560 + C561 CE508 C559 0.1uF/50V0.1uF/50V NC/9PIN/2.0mm
JMP A10 12 820uF/50V
Alternative A12
22 22 22 22 22 1500uF/50V 1500uF/50V 250uH XP2
SW1JP506 NC Alternative 9PIN/2.0mm
NC 4 PCON 1 1:PSon
R596 NC/10 4 R579 M-GND 2 1
Alternative Alternative 2:M-GND
0.1uF/50V/X7R 0.1uF/50V/X7R 0.1uF/50V/X7R M36V 3 2 3:M36V
R524 D507 5 4 3 4:+36V

B
P-GND JP509
BD501 R511 FR307/3A/1000V D534 7 NC/0 36V 5 4 5:+36V
Q543 A7 6 5
+ 1

M7J/1A/1000V T501_S2 OP- OP+ M-GND GND 6:+36V

R581
JP514 3904 JP510
NC/FR107/1A/1000V FB_GND R570 7 6 7:GND
33K 10mŸ GND 8 7 8:GND
D502 NC
2 3 RV503 CE504 CE5042 NC R563 0/NC 0 P 9 8 9:GND
VCC 2.7K NC/FR107 FB 6 R536 9
JMP 0 FB R557 R558
+ +
R587 ZD508 R533 + R564
4 -

NC 150uF/450V NC + CE505 ZD509 100K/1%

KBU610 CE509 BZX79C18 47uF/50V BAT54C
100uF/50V BZX79C15 3K
R537
NC CY507 NC/470pF/250VAC 2 33K
D503
HV
R525 3 CE510 OPVCC

5
+
C505 68 R535 CY506 470pF/250VAC 1

HV

NC

VCC

OUT
BAS316/100V/0.5A 1uF/50V

U501
Q614
10
270K D504 OTP option
LIF502 NCP1271 PNP_MMBT8550CLT1 Q501 R545
D532
0.1uF/50V/X7R R544

D
COMP
L R588 75K/1%

GND
0 D520 27K/1%
CS
RT

S
Q503 R589
NC/M7J/1A/1000V Skip/Latch 12N65 OPP

D
D533 R553

C
1

4
C515
N R522 68 D505 BAS316/100V/0.5A R531 10 2.49K
100pF/50V/NP0

1
S
R503 1M R504 1M C512 R517 10pF/1KV NPN_3DG3904M
2.2K
18K C507 R529 Q613 12N65 U502 BAS316/100V/0.5A R578
0.01uF/50V/X7R

NC/M7J/1A/1000V 1.5K
N R530 R534 LTV-817S-B C530 Q510
PNP_MMBT8550CLT1 NC/100

2
CX502 0.33uF/275VAC C511 C554 470pF/50V/NP0 0.1uF/50V/X7R C529
CY503 CY505 TR503 TR502
470pF/250VAC 470pF/250VAC 10K 10K 0.1uF/50V/X7R
0.047uF/50V/X7R ZD505 CE542 +
NC/NTC/10Kohm
NTC/10Kohm
NC/220uF/6.3V

NC/220pF/50V/NP0

NC/220pF/50V/NP0
P R5052 R5051 R5054 R5053 R554 10K C555 20K/1%
C516 C514 BZX79C15 R560
R592

2
R591
LIF501 0.2R NC 0.2R NC U503 0.1uF/50V/X7R R556 13K/1%
1
0 AS431
0

3
R520 100
N
L PCON
R565
CX501 0.33uF/275VAC

R501 R505 V1 R562

D
R502 1M NC/1M Vcc
1M T502 NC/2.2K/1% 0
P
NC/ER40 R572 Q542
ZD504 0
R513 VCC
LIF505 D510 NC/100 HV 1 9 T501_S3 BZX79C39 NC/3904
R583 VDD 9 10 R566 C541
Q507 10 R573
NC/1M 680 NC/0.1uF/50V/X7R NC/2.2K
NC/PNP_MMBT8550CLT1

1mH NC/1N4148

1
RV501 VDR/620V
Q506 2 U504
NC/PNP_3CG3906M

N.C D514
F501 R539
C501 OPP

2
TR501 R506
LTV-817S-B 2.49K/1%
NC/0.47uF/63V

R567 1N4148
T501_P13 Skip/Latch
D D513
NTC NC/2.2M 680 OP+ R532 1.5K 8
12 T501_S2 R576 PCON OPVCC <Package>
FUSE_6.3A/250V 12 14 Skip/Latch R575 3 V+
14 NC/11k +
1
CN501 NC/1k 1N4148 OP- R528 3.3K 2
-
1
2

CY502 Q545 + CE541 V-

N L 5
1
2

5 R568 4 LM3580
10uF/50V C502

E 220pF FB_GND6 NC/3904 U506A C503

6 8 0.1uF/50V/X7R R538 100K/1%
8
4

1
P 2PIN/7.92mm R574 0.1uF/50V/X7R
C543 U505 NC/11k R569 C504 2200pF/50V/X7R
NC/1k
NC/0.1uF/50V/X7R R546 Q544 NC/1k
3

2
FB 7
R593 R594 R595 7 NC/1LTV-817S-B
VCC VCC 3904
NC/115K/1% C542 R571
0 0 0 NC/11k
NC/10.1uF/50V/X7R

Alternative
* CAUTION :
Input voltagle 100~240VAC OR 220~240VAC(LA9)
CE503 150uF/450V
THE PARTS MARKED WITH ARE IMPORTANT PARTS ON THE SAFETY.

F
CE504 150uF/450V PLEASE USE THE PARTS HAVING THE DESIGNATED PARTS NUMBER WITHOUT FAIL.
Input voltalge 100~120VAC(UC2,JP1)
CE503 150uF/250V
CE504 150uF/250V

GTK-XB7
43 43
 GTK-XB7

• IC Block Diagrams U16 STM32F030R8T6

Serial POWER
– MAIN Board – SWCLK
VDD18
Wire VOLT.REG
U1 LED1642GWTTR SWDIO VDD = 2.4 to 3.6 V
Debug 3.3 V TO 1.8 V

Obl
VSS
as AF Flash

interface
SDO PWCLK up to @ VDD

Flash
64 KB,
CORTEX-M0 CPU POR SUPPLY
32 bits
fHCLK = 48 MHz Reset SUPERVISION
SDI Int
Control Logic & OUT0 NRST

Bus matrix
CLK

controller
PWM SRAM POR/PDR VDDA
Data Registers

SRAM
@ VDDA VDD
LE counter 4 / 8 KB
NVIC RC HS 14 MHz
OUT1
RC HS 8 MHz
VDD UVLO @ VDDA
Error GP DMA
& POR RC LS @ VDD
GND 5 channels OSC_IN (PF0)
detection OUT2 XTAL OSC
PLL OSC_OUT (PF1)
4-32 MHz

…………
IWDG
Thermal Power

16 output channels
Configuration shutdown AHBPCLK Controller
RESET & APBPCLK
register ADCCLK @ VDD
CLOCK
USARTCLK OSC32_IN (PC14)
CONTROL HCLK
XTAL32 kHz
PA[15:0] GPIO port A OSC32_OUT (PC15)
FCLK

Channel driver OUT14 PB[15:0] GPIO port B RTC TAMPER-RTC

AHB decoder
Current Current gain (ALARM OUT)
R-EXT Ref. Timing control RTC interface
adjustment PC[15:0] GPIO port C CRC
Turn ON/OFF OUT15
Gradual delay PD2 GPIO port D

PF[1:0] GPIO port F 4 channels

PF[7:4] TIMER 1 3 compl. channels
BRK, ETR input as AF
TIMER 3 4 ch., ETR as AF

AHB TIMER 14 1 channel as AF

APB 2 channels
TIMER 15 1 compl, BRK as AF

EXT. IT 1 channel
55 AF TIMER 16 1 compl, BRK as AF
WKUP
U3, 4 EUP3490 MOSI,
WWDG
TIMER 17 1 channel
1 compl, BRK as AF
MISO,
SPI1 IR_OUT as AF
SCK, DBGMCU
NSS as AF
USART1 RX, TX,CTS, RTS,
MOSI/MISO, CK as AF
SPI2
SCK/NSS, USART2 RX, TX,CTS, RTS,
as AF CK as AF
SYSCFG IF

SCL, SDA, SMBA

I2C 1
(20 mA for FM+) as AF
@ VDDA
Temp. SCL, SDA
I2C2
sensor as AF
16 12-bit
AD inputs IF
ADC1
TIMER 6
VDDA
VSSA

GTK-XB7
44 44
 AVSS_PLL
VRA_PLL

VR_PLL
AVDD_PLL
VRD_PLL
DVSS
AVSS

VBGAP
AVDD_REF
DVDD
AVDD
Power Supply
U17 TAS5534

MCLK PWM_HPP and MR

Digital Audio Processor PWM Section
PWM_HPP and ML
0 7 Soft Soft Loud DC De Interpolate SRC NS PWM
Det Biquads Tone Vol Comp DRC Block Emph PWM AP and AM1 L Front
PLL_FLTM
0 7 Soft Soft Loud DRC DC De Interpolate SRC NS PWM
PLL_FLTP Det Biquads Tone Vol Comp Block Emph
OSC CAP
PWM AP and AM2 R Front
SCLK 0 7 Soft Soft Loud DC De Interpolate SRC NS PWM
LRCLK Det Biquads Tone Vol Comp DRC Block Emph

8
8
Device
SDIN1
SDIN2 Control 0 7 Soft Soft Loud DC De Interpolate SRC NS PWM

Clock, PLL, and Serial Data I/F

Det Biquads Tone Vol Comp DRC Block Emph
SDIN3
SDIN4
0 7 Soft Soft Loud DC De Interpolate SRC NS PWM PWM AP and AM7 Center
Det Biquads Tone Vol Comp DRC Block Emph
I2 C
SDA
Serial PWM AP and AM8

8 Crossbar Mixer
Output Control

2 Crossbar Mixer
0 7 Soft Soft Loud DC De Interpolate SRC NS PWM
Control Det Biquads Tone Vol Comp DRC Block Emph Subwoofer
SCL
I/F
0 7 Soft Soft Loud PWM AP and AM5 L Surround
DC De Interpolate SRC NS PWM
RESET Det Biquads Tone Vol Comp DRC Block Emph PWM L Lineout
PDN
0 7 Soft Soft Loud DC De Interpolate SRC NS PWM PWM AP and AM6 R Surround
PWM R Lineout

DAP Control
MUTE Det Biquads Tone Vol Comp DRC Block Emph

System Control
HP_SEL
BKND_ERR 8 8 8 VALID
8 4 8 2

2
Volume
9 Control PSVC PSVC

PWM Control

45
GTK-XB7
GTK-XB7

U18 TAS5624A

/CLIP

/OTW

/FAULT
BST_X
GVDD_X
UVP AVDD
DVDD
/RESET

MODE1-3

PROTECTION & I/O LOGIC

POWER-UP
RESET
AVDD
AVDD
TEMP
SENSE
VDD

DVDD CB3C OVER-

DVDD LOAD
PROTECTION

STARTUP
CONTROL
C_START

BST_A

PVDD_AB
PWM
INPUT_A
RECEIVER ANALOG + PWM &
TIMING GATE-DRIVE OUT_A
LOOP FILTER
- CONTROL

GND

GVDD_AB

BST_B

PVDD_AB
PWM
INPUT_B
RECEIVER ANALOG + PWM &
TIMING GATE-DRIVE OUT_B
LOOP FILTER
- CONTROL

GND

BST_C

PVDD_CD
PWM
INPUT_C
RECEIVER ANALOG + PWM &
TIMING GATE-DRIVE OUT_C
LOOP FILTER
- CONTROL

GND

GVDD_CD

BST_D

PVDD_CD
PWM
INPUT_D
RECEIVER ANALOG + PWM &
TIMING GATE-DRIVE OUT_D
LOOP FILTER
- CONTROL

GND

46
 GTK-XB7

U27 SRC4182

U32 SY8089

47
GTK-XB7

U35 KXCJK-1013

X
Sensor

Y Charge
Sensor A/D
Amp

Z
Sensor

Vdd 14 Digital
2
Filter
I C
IO Vdd 1 Digital Engine
GND 5
4 6 7 11

48

Note:
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• Items marked “*” are not stocked since
they are seldom required for routine ser-
vice. Some delay should be anticipated
when ordering these items.
GTK-XB7
SECTION 5
EXPLODED VIEWS
• The mechanical parts with no reference
The components identified by mark 0
number in the exploded views are not sup-
or dotted line with mark 0 are critical for
plied.
safety.
• Color Indication of Appearance Parts Ex-
Replace only with part number specified.
ample:
KNOB, BALANCE (WHITE) . . . (RED) Les composants identifiés par une marque
  0 sont critiques pour la sécurité.
Parts Color Cabinet’s Color Ne les remplacer que par une pièce por-
tant le numéro spécifié.

5-1. SIDE PANEL SECTION

6
3
not supplied not supplied not supplied
not
supplied not supplied
top cover section
not supplied
not supplied
not supplied
not supplied
not supplied

not supplied
FFC1

not supplied

not supplied not supplied

not supplied
not supplied
not supplied
not supplied
4

1 not supplied
not supplied
not supplied

not supplied

not supplied
cabinet section not supplied
not supplied

6 not supplied

not supplied 5

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 9-885-209-50 SIDE PANEL (L UC2_BLACK) 5 9-885-209-55 RUBBER (LARGE CIRCLE BLACK) (8 pieces, 1 set)
2 9-885-209-48 SIDE PANEL (R UC2_BLACK)
3 9-885-209-56 RUBBER (CIRCLE BLACK) (4 pieces, 1 set) 6 9-885-210-26 RUBBER (SMALL CIRCLE BLACK) (4 pieces, 1 set)
4 9-885-209-57 RUBBER (SQUARE BLACK) (4 pieces, 1 set) FFC1 9-885-209-33 FFC (TO MAIN)

49
GTK-XB7

5-2. CABINET SECTION

not supplied not supplied

not supplied not supplied

not supplied
not supplied
not supplied

A
C

B MAIN board section

D

not supplied

not supplied
not supplied SP2
not supplied not supplied not supplied
not supplied
not supplied
A not supplied
B not supplied
C
D
SP1 F
E
not supplied
not supplied
not supplied
not supplied
not supplied
not supplied not supplied
not supplied not supplied
not supplied

not supplied 51

not supplied
F
not supplied not supplied

front panel section not supplied not supplied

not supplied
not supplied
52

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
51 9-885-209-52 BOTTOM COVER (BLACK) + PLATE SP1 9-885-209-43 SPEAKER UNIT (WF) (160 mm) (Woofer)
52 9-885-209-55 RUBBER (LARGE CIRCLE BLACK) (8 pieces, 1 set) SP2 9-885-209-43 SPEAKER UNIT (WF) (160 mm) (Woofer)

50
 GTK-XB7

5-3. TOP COVER SECTION

103

not supplied

102

FFC2

101
not supplied
not supplied
not supplied
not supplied
not supplied not supplied
not supplied
not supplied
not supplied

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
101 9-885-209-34 CONTROL BOARD, COMPLETE 103 9-885-209-47 TOP COVER (BLACK) + PLATE
102 9-885-209-32 BT&NFC BOARD, COMPLETE FFC2 9-885-209-35 FFC (TO BT&NFC)

51
GTK-XB7

5-4. MAIN BOARD SECTION

not supplied 153

not supplied
not supplied
not supplied not supplied
not supplied

not supplied
not supplied

G not supplied not supplied H I

not supplied not supplied

not supplied
152
not supplied
not supplied not supplied

151
M1

not supplied

not supplied
G not supplied

not supplied
not supplied

I not supplied

not supplied

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
151 9-885-209-29 PSU BOARD, COMPLETE 153 9-885-209-45 USB + KEY BOARD, COMPLETE
152 9-885-209-27 MAIN BOARD, COMPLETE 0 M1 9-885-209-46 FAN UNIT

52
 GTK-XB7

5-5. FRONT PANEL SECTION

• Rear view

206
not supplied

not supplied
not supplied
SP3
not supplied

203
not supplied
not supplied
not supplied
SP4
WR1 not supplied
201 not supplied not supplied

not supplied not supplied

not supplied
not supplied not
205 supplied
not supplied
not supplied
not supplied
not supplied not supplied
not supplied not supplied
not supplied SP5
not supplied FFC3
not supplied
204
not supplied
not supplied
not supplied
not supplied
not supplied
not supplied
not supplied
not supplied
not supplied 202
not supplied not supplied
not supplied
not supplied

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
201 9-885-209-38 LA BOARD, COMPLETE FFC3 9-885-209-40 FFC CABLE
202 9-885-209-39 LB BOARD, COMPLETE SP3 9-885-209-44 SPEAKER UNIT (TW) (50 mm) (Tweeter)
203 9-885-209-36 RGBE BOARD, COMPLETE SP4 9-885-209-44 SPEAKER UNIT (TW) (50 mm) (Tweeter)
204 9-885-209-37 RGBF BOARD, COMPLETE SP5 9-885-209-44 SPEAKER UNIT (TW) (50 mm) (Tweeter)
205 9-885-209-42 IR BOARD, COMPLETE
WR1 9-885-209-41 CABLE
206 9-885-209-53 FRONT PANEL (UC2 BLACK) ASSY

53
GTK-XB7
SECTION 6
ACCESSORIES
Ref. No. Part No. Description Remark
4-582-492-11 MANUAL, INSTRUCTION
(ENGLISH, FRENCH, SPANISH)

501 1-493-170-11 REMOTE COMMANDER (RMT-AM200U)

(Remote control)
0 502 9-885-209-81 AC CORD (UC2) (AC power cord)

501 502

The components identified by mark 0

or dotted line with mark 0 are critical for
safety.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce por-
tant le numéro spécifié.

54
 GTK-XB7

MEMO

55
GTK-XB7

REVISION HISTORY

Ver. Date Description of Revision

1.0 2016.01 New