Professional Documents
Culture Documents
Labor Guidelines IPSD Repair Times C1.5 Through C7.1 Industrial Engines 28.01.16 TRG
Labor Guidelines IPSD Repair Times C1.5 Through C7.1 Industrial Engines 28.01.16 TRG
DISCLAIMER: The repair labor time information in this publication is provided for informational purposes only. Any repair
procedures and safety information in the applicable published Caterpillar® service repair manuals should be followed. The repair
labor time information in this publication is not all inclusive and is available to provide approximate repair labor times only. The
repair operations and details listed in this publication are provided to generally show what was included in developing the repair
labor time.
Page 1 of 5 1/28/2016
The following repairs include all "start‐by" components, as outlined in the Disassembly & Assembly (D&A) Manual.
Times do not include removal of after treatment unless stated otherwise.
If draining of the coolant is required to carry out a procedure, it is not included in this document as the time required will be application specific.
If draining of the engine oil is required to carry out a procedure, it is not included in this document as the time required will be application specific.
Repair Times (hours) by Engine Model S/N prefix
C4.4 C6.6
C7.1 C3.4B C1.5 C2.2 C7.1 C7.1
444 448 D3K G9N
SMCS SMCS SMCS SMCS 666 667 G9P C9R
Comp Job Mod Qty Operation Description 770 881 CJG D1R C9T 630 673 G9R Comments
1052 010 SI Turbocharger (Side Mounted) – Remove and install side ‐ 1.3 0.9 1.0 1.0
1052 010 UZ Turbocharger (Top Mounted) – Remove and Install upper ‐ 1.4 ‐ 1.0 1.0
1057 010 Wastegate Solenoid – Remove & Install 0.8 0.2 ‐ ‐ 0.8
Exhaust Elbow between the Turbocharger and the
1061 010 9TE Exhaust Elbow ‐ Remove and Install TURBOCHARGER TO EXHAUST ‐ ‐ 0.3 ‐ ‐ Aftertreatment Regeneration Device (ARD))
1061 010 9TE Exhaust Pipe ‐ Remove and Install TURBOCHARGER TO EXHAUST (flexpipe) 1.5 0.4 0.3 ‐ ‐ Exhaust flexpipe
Exhaust Elbow between the (Aftertreatment Regeneration
1061 010 CCC Exhaust Elbow ‐ Remove and Install FROM COMB BODY TO DPF ‐ ‐ 0.6 ‐ ‐ Device (ARD) and the Clean Emission Module (CEM)
1061 010 Exhaust Elbow ‐ Remove and Install ‐ ‐ ‐ 0.2 0.2
1082 010 Exhaust Gas Recirculation Valve ‐ Remove and Install ‐ 0.4 0.3 ‐ ‐
1091 010 Catalyst ‐ Remove and Install 2.6 ‐ ‐ ‐ ‐ Diesel Oxidation Catalyst (DOC)
1096 010 Oxygen Sensor ‐ Remove and Install ‐ 0.2 ‐ ‐ ‐ Catalytic Converter
1102 010 YA Rocker Shaft Remove & Install with W/ATTACHED COMPONENT(S) 1.3 1.2 1.4 0.9 1.3 remove with push rods
1107 010 ZS Engine Oil Pressure Switch ‐ Remove and Install (Valve Cover R&I switch) ‐ ‐ 0.1 ‐ ‐ Engine Oil Pressure Switch in Valve Mechanism Cover
1122 010 Engine Lifting Bracket – Remove ‐ 0.3 ‐ ‐ ‐
1151 010 HD Housing (Front) ‐ Remove and Install Heavy Duty 4.9 ‐ ‐ ‐ 4.9 Heavy Duty Housing (Front)
1151 010 YA Housing (Front) – Remove and Install W/Attached components 4.7 ‐ ‐ ‐ 4.7 Add 0.6 if equipped with an accessory drive
1151 010 Housing (Front) ‐ Remove and Install ‐ 2.4 3.5 4.6 ‐
C1.5/C2.2 (C9R/C9T) only ‐ New housing assemble add 70
1151 017 Housing (Front) ‐ Disassemble and Assemble ‐ ‐ 0.7 ‐ ‐ minutes for Governor adjustments
1156 010 YA Flywheel ‐ Remove and Install W/ATTACHED COMPONENT(S) 0.7 ‐ ‐ ‐ 0.7 Equipped with Rear Power Take‐Off
1156 010 Flywheel ‐ Remove and Install 0.5 0.5 0.4 0.5 0.5
1157 010 WE Flywheel Housing – Remove and Install Wet 1.2 ‐ ‐ ‐ 1.2 Wet Back End Housing
1157 010 WX Flywheel Housing – Remove and Install with named component(s) ‐ ‐ 1.9 ‐ ‐ Engines with Flywheel Housing and Back Plate
1157 010 Flywheel Housing – Remove and Install 1.2 1.4 1.8 1.0 1.2
1160 010 Crankshaft Front Seal ‐ Remove and Install 0.6 0.6 0.7 0.9 0.6 C1.5/C2.2 ‐ Add 0.2 if equipped with ARD Air Pump
Alternative procedure if the front housing must be removed to
1160 010 Crankshaft Front Seal ‐ Remove and Install ‐ ‐ 3.1 ‐ ‐ carry out the procedure
1160 010 Crankshaft Front Seal ‐ Remove and Install 0.7 ‐ ‐ ‐ 0.7 Crankshaft Front Seal for Heavy Duty Front Cover
1161 010 WE Crankshaft Rear Seal ‐ Remove and Install Wet 1.5 ‐ ‐ ‐ 1.5 Wet Back End
Page 2 of 5 1/28/2016
The following repairs include all "start‐by" components, as outlined in the Disassembly & Assembly (D&A) Manual.
Times do not include removal of after treatment unless stated otherwise.
If draining of the coolant is required to carry out a procedure, it is not included in this document as the time required will be application specific.
If draining of the engine oil is required to carry out a procedure, it is not included in this document as the time required will be application specific.
Repair Times (hours) by Engine Model S/N prefix
C4.4 C6.6
C7.1 C3.4B C1.5 C2.2 C7.1 C7.1
444 448 D3K G9N
SMCS SMCS SMCS SMCS 666 667 G9P C9R
Comp Job Mod Qty Operation Description 770 881 CJG D1R C9T 630 673 G9R Comments
1202 010 RIN Crankshaft Timing Ring ‐ Remove and Install 5.3 ‐ ‐ ‐ 5.3 Add 0.3 for heavy duty front gear group
1202 010 RIN Crankshaft Timing Ring ‐ Remove and Install ‐ 4.8 ‐ ‐ ‐ If Balancer removal is necessary add 0.2
Add 0.2 if primary & secondary fuel filters are installed to the
1202 010 Crankshaft – Remove and Install 11.3 ‐ 5.9 8.9 11.3 cylinder head)
1202 010 Crankshaft – Remove and Install ‐ 4.3 ‐ ‐ ‐ If Balancer removal is necessary add 0.1
1203 010 Crankshaft Main Bearings ‐ Remove and Install 2.4 ‐ ‐ 2.4 2.4 Crankshaft in position)
1204 010 Crankshaft Gear ‐ Remove and Install 6.1 ‐ 3.3 5.9 6.1 Add 0.3 for heavy duty front housing
1205 010 Vibration Damper and Pulley ‐ Remove and Install 0.7 ‐ ‐ 0.7 0.7
1206 010 HD Idler Gear Heavy Duty – Remove and install 3.4 ‐ ‐ ‐ 3.4 Heavy Duty Front Cover
1206 010 Idler Gear – Remove and Install 2.4 1.7 ‐ 2.8 2.4
1210 10 Camshaft ‐ Remove and Install 6.4 2.3 8.1 3.3 6.4 If Balancer removal is necessary add 0.1
1212 010 Camshaft Gear ‐ Remove and Install 2.3 2.0 ‐ 3.7 2.3 Add 0.1 for heavy duty front cover
1225 010 S Pistons and Connecting Rods – Remove and Install Set(All) ‐ ‐ 7.2 ‐ ‐
Add 0.1 for each piston & connecting rod that is removed. (If
1225 010 F Pistons and Connecting Rods – Remove and Install First One ‐ 1.5 ‐ ‐ ‐ Balancer removal is necessary add 0.1)
Add 0.2 for each piston & connecting rod that is removed. (Add
0.2 if primary & secondary fuel filters are installed to the
1225 010 F Pistons and Connecting Rods – Remove and Install First One 6.1 ‐ ‐ 4.5 6.1 cylinder head)
1225 017 Pistons and Connecting Rods – Disassemble and Assemble (per cylinder) 0.3 0.2 0.2 0.3 0.3
1251 010 Fuel Injection Pump Gear ‐ Remove and Install 2.9 0.9 ‐ 2.7 2.7
125H 010 HP Fuel Injection Pump ‐ Remove and Install 2.5 1.6 1.2 3.7 3.5
1252 010 HQ High pressure fuel lines – Remove and Install 2.8 0.6 0.3 0.6 2.8
1258 010 Fuel Priming Pump – Remove and Install 0.3 ‐ 0.2 ‐ 0.3
1258 010 Fuel Priming Pump – Remove and Install ‐ 0.3 ‐ 0.3 0.3 Mechanical Priming Pump
1290 010 A Electronic Unit Injector – Remove and Install Each additional 0.5 0.2 0.2 0.2 0.5 Time for each additional Injector
1290 010 F Electronic Unit Injector ‐ Remove and Install First One 3.4 0.7 0.7 0.8 3.4 Time for one Injector
1302 010 Engine Oil Pan ‐ Remove and Install 0.7 ‐ 0.2 0.7 0.7 Aluminium Oil Pan
1302 010 PH Engine Oil Pan – Remove and Install Plate 0.4 ‐ ‐ ‐ ‐ Aluminium Oil Pan
1302 010 Engine Oil Pan – Remove and Install ‐ 0.4 ‐ ‐ ‐ Pressed steel Oil Pan
1302 010 Engine Oil Pan ‐ Remove and Install ‐ 0.4 ‐ 0.7 ‐ Cast Iron Engine Oil Pan
1306 010 Engine Oil Filter Base – Remove and Install 0.3 0.2 ‐ 0.2 0.3
1307 010 Engine Oil Line ‐ Remove and Install ‐ ‐ 0.2 ‐ ‐
1317 010 OT Crankcase Breather – Remove and Install excludes turbocharger ‐ ‐ 0.2 ‐ ‐ Naturally Aspirated C2.2 Engine
1317 010 WT Crankcase Breather – Remove and Install with turbocharger ‐ ‐ 0.4 ‐ ‐ For Turbocharged C2.2 Engine
1331 010 S Piston Cooling Jets – Remove and Install Set(All) 1.2 4.2 ‐ 1.2 1.2
Page 3 of 5 1/28/2016
The following repairs include all "start‐by" components, as outlined in the Disassembly & Assembly (D&A) Manual.
Times do not include removal of after treatment unless stated otherwise.
If draining of the coolant is required to carry out a procedure, it is not included in this document as the time required will be application specific.
If draining of the engine oil is required to carry out a procedure, it is not included in this document as the time required will be application specific.
Repair Times (hours) by Engine Model S/N prefix
C4.4 C6.6
C7.1 C3.4B C1.5 C2.2 C7.1 C7.1
444 448 D3K G9N
SMCS SMCS SMCS SMCS 666 667 G9P C9R
Comp Job Mod Qty Operation Description 770 881 CJG D1R C9T 630 673 G9R Comments
1335 010 ANT Soot Antenna ‐ Remove and Install (Particle sensor R&I antenna) 0.2 ‐ ‐ ‐ ‐
Page 4 of 5 1/28/2016
The following repairs include all "start‐by" components, as outlined in the Disassembly & Assembly (D&A) Manual.
Times do not include removal of after treatment unless stated otherwise.
If draining of the coolant is required to carry out a procedure, it is not included in this document as the time required will be application specific.
If draining of the engine oil is required to carry out a procedure, it is not included in this document as the time required will be application specific.
Repair Times (hours) by Engine Model S/N prefix
C4.4 C6.6
C7.1 C3.4B C1.5 C2.2 C7.1 C7.1
444 448 D3K G9N
SMCS SMCS SMCS SMCS 666 667 G9P C9R
Comp Job Mod Qty Operation Description 770 881 CJG D1R C9T 630 673 G9R Comments
1923 010 Atmospheric Pressure Sensor ‐ Remove and Install 0.1 ‐ ‐ ‐ ‐
1924 010 Engine Oil Pressure Sensor ‐ Remove and Install 0.1 0.1 0.1 ‐ 0.1
105H 010 Turbocharger (Second Stage) high pressure – Remove and Install 3.0 ‐ ‐ ‐ ‐
105L 010 Turbocharger (First Stage) low pressure – Remove and Install 1.0 ‐ ‐ ‐ ‐
108A 010 Combustion Head Group (ARD) ‐ Remove and Install 0.9 ‐ ‐ ‐ ‐ Pilot Only System
108A 010 Check Valve (ARD Air Supply) ‐ Remove and Install ‐ ‐ 8.0 ‐ ‐
108B 010 TMS Flame Detection Temperature Sensor ‐ Remove and Install 0.5 ‐ 0.1 ‐ ‐ Flame Detection Temperature Sensor for the ARD
Support and Mounting for Rear mounted Clean Emission
108D 010 S4 L Support and Mounting (Clean Emissions Module (CEM)) limited qty ‐ ‐ 0.8 ‐ ‐ Module (CEM)
108D 010 S4 Support and Mounting (Clean Emissions Module (CEM)) ‐ 0.9 0.4 ‐ ‐
108F 010 PXS Pressure Sensor (DPF) ‐ Remove and Install (DPF R&I pressure sensor) 0.2 0.2 0.1 ‐ ‐ Clean Emissions Module
Page 5 of 5 1/28/2016