Professional Documents
Culture Documents
ProteusRound1 Final
ProteusRound1 Final
ELECTROVERT 2018
Name of the Event: Pro-Minance Date: 5 OCT, 2019
Candidate’s Code: Time:30 min
Instructions
Use of mobile is not allowed.
Use of scientific calculator is allowed.
Every questions carry one mark with no negative marking.
1. The center frequency of a band-pass filter D. both Iout and IBIAS
is always equal to the
A. bandwidth
B. –3 dB frequency 5.
C. bandwidth divided by Q
D. geometric average of the critical
frequencies
1
7. To achieve the optimum transient response, the 13. Which of these circuits will give yield carry
indicating instruments are so designed as to with more delay
A. be undamped. 1. Carry look ahead adder
B. be critically damped. 2. Ripple carry adder
C. provide damping which is slightly less than A. 1.
the critical value. B. 2.
D. provide damping which is slightly more C. both are same
than the critical value. D. none
8. Which one of the following is not a vectored 14. A metal strain gauge has a gauge factor of
interrupt two. Its nominal resistance is 120 ohms. If it
A. TRAP. undergoes a strain of 10-5, the value of change
B. RST 7.5. of resistance in response to the strain is
C. RST 6.5. A. 0.0024 Ohm.
D. INTR B. 0.0012 Ohm.
C. 240 Ohm.
9. The fast logic family is
D. 120 Ohm.
A. ECL.
B. DRL. 15. For most static RAM, the write pulse width
C. TRL. should be atleast:
D. TTL. A. 10 ns
B. 60 ns
10. An 8 × 4 ROM contains a decoder of size
C. 300 ns
A. 3×8
D. 1 µs
B. 8×4
C. 8×8 16. In DIBL, which among the following is/are
D. 3×4 regarded as the source/s of leakage?
A. Subthreshold conduction
11. Which of the following BCD codes with an
B. Gate leakage
odd parity bit included in the end of code
C. Junction leakage
group, have error in the code?
D. All of the above
(I)1001010110000
(II)0100011101100
(III)0111110000011 17. Find the equivalent resistance between A and
(IV)1000011000101 B.
A. 32ohm
A. Both (I) & (II) B. 31ohm
B. Both (I)&(IV) C. 30ohm
D. 29ohm
2
the points at which the technician pressed the
key. What is most likely wrong with the circuit?
A. 5k5
B. 35,200 ohms
C. 55k
A. Pulse Circuit
B. Timing Circuit/Delay Circuit D. None of the above
C. Oscillator Circuit/Frequency Circuit
D. Schmitt Circuit
24. The lead marked with the arrow is: 28. Determine currents I1 , I2 and I3
A. The Collector
B. The Base
C. The Emitter
D. The case
C. 22,000p p = picofarad 30. A 500 kVA single phase transformer has 90%
efficiency at both half load and full load at
D. All of the above unity power factor. Then iron losses will be
A. 12.55 KW
B. 13.55 kW
C. 16.55 kW
D. 18.55 KW
4
i
n
p
u
t
o
f
2
0
V
p
e
a
k
t
o
t
h
e
g
i
v
e
n
c
i
r
c
u
i
t
,
w
h
a
t
i
s
t
h
e
p
e
a
k
v
a
5