Professional Documents
Culture Documents
JN0 360
JN0 360
QUESTION NO: 1
Which two statements are true about MPLS VPNs? (Choose two.)
A.
With Layer 3 VPNs, the provider’s routers participate in the customer’s Layer 3 routing.
B.
MPLS VPNs are designed to run over private networks rather than the public Internet.
C.
With Layer 2 VPNs, the provider does not participate in the routing of the customer’s private IP
traffic.
D.
MPLS VPN tunnels are always encrypted.
Answer: A,C
Explanation:
QUESTION NO: 2
A.
inject
B.
pop
C.
push
D.
swap
Answer: D
Explanation:
http://www.juniper.net/techpubs/software/junos-security/junos-security96/junos-security-swconfig-
interfaces-and-routing/mpls-ov.html
QUESTION NO: 3
A.
T Series devices
B.
SRX Series devices
C.
MX Series devices
D.
MAG Series devices
Answer: B
Explanation:
http://www.juniper.net/techpubs/en_US/junos10.0/information-products/pathway-pages/mx-
series/ethernet-switching-mx-series.html
QUESTION NO: 4
A.
a company spread across multiple floors of a building
B.
a company with a single office
C.
a home network
D.
the public Internet
Answer: D
Explanation:
QUESTION NO: 5
For a network running single-area OSPF, how would you decrease the size of the link-state
database (LSDB)?
A.
Implement RIP as an overlay protocol on all devices.
B.
Add more devices to the OSPF network to help with LSDB processing.
C.
Reduce the frequency of hello timers throughout the network.
D.
Implement OSPF areas.
Answer: D
Explanation:
QUESTION NO: 6
A.
IP addresses that are reserved for use only with MPLS VPNs.
B.
IP addresses that are never installed in the routing table.
C.
IP addresses that are reserved for use only with GRE tunnels.
D.
IP addresses specifically used for out-of-band management.
Answer: B
Explanation:
Which statement correctly describes the difference between a generated and an aggregate route?
A.
An aggregate route can be a supernet whereas generated routes are classful.
B.
A generated route has a forwarding next hop that is inherited from a contributing route.
C.
An aggregate route has a forwarding next hop that is inherited from a contributing route.
D.
Only aggregate routes can be re-advertised through BGP using a policy.
Answer: B
Explanation:
QUESTION NO: 8
A.
All IPv4 routes in the master routing instance are shared with user-defined routing instances.
B.
Interface routes in the master routing instance are shared with user-defined routing instances.
C.
Routes in the master routing instance are not shared with user-defined routing instances.
D.
All routes in the master routing instance are shared with user-defined routing instances.
Answer: C
Explanation:
QUESTION NO: 9
Which routing table contains the route information for the user-defined routing instance called
A.
inet.Candidate1.0
B.
Candidate1.inet.0
C.
inet.0
D.
Candidate1-inet.0
Answer: B
Explanation:
QUESTION NO: 10
Which two routing-instance types are used for non-VPN-related applications? (Choose two.)
A.
virtual-router
B.
vrf
C.
forwarding
D.
vpls
Answer: A,C
Explanation:
QUESTION NO: 11
What are two characteristics of load-balancing implementation on a Junos device? (Choose two.)
A.
"Pass Any Exam. Any Time." - www.actualtests.com 6
Juniper JN0-360 Exam
It balances packets on a per-packet basis.
B.
It balances packets on a per-flow basis.
C.
It is enabled through a policy.
D.
It is enabled by default.
Answer: B,C
Explanation:
QUESTION NO: 12
A network administrator has been asked to configure the most specific aggregate route to
summarize the four specific prefixes shown below:
10. .5.0/24
10. .12.0/24
10. .17.0/24
10. .21.0/24
A.
[edit routing-options]
user@router# show
aggregate {
B.
[edit routing-options]
user@router# show
aggregate {
"Pass Any Exam. Any Time." - www.actualtests.com 7
Juniper JN0-360 Exam
route 10. .0.0/20;
C.
[edit routing-options]
user@router# show
aggregate {
D.
[edit routing-options]
user@router# show
aggregate {
Answer: A
Explanation:
QUESTION NO: 13
A.
Unified ISSU is built upon graceful-restart extensions to allow upgrades with no impact to the data
plane.
B.
Unified ISSU is supported on systems with single or dual Routing Engines.
C.
Unified ISSU permits both upgrades and downgrades with no control plane disruption and is
based on the graceful Routing Engine switchover (GRES) feature.
D.
Unified ISSU is based on nonstop-routing (NSR) and graceful Routing Engine switchover (GRES),
and permits software upgrades only.
QUESTION NO: 14
R0 is a Juniper Networks MX router with dual Routing Engines. You must load new software on
R0 while ensuring no control plane disruption and minimal data loss.
A.
graceful restart
B.
NSR
C.
graceful Routing-Engine switchover (GRES)
D.
unified ISSU
E.
BFD
Answer: B,C,D
Explanation:
QUESTION NO: 15
What are two ways that nonstop routing works? (Choose two.)
A.
by enabling redundant REs to switch from primary RE to backup RE
B.
by alerting peer nodes of any routing table changes
C.
by enabling redundant REs to run a different version of the Junos OS
Answer: A,D
Explanation:
QUESTION NO: 16
What are three ways that graceful Routing Engine switchover provides redundancy? (Choose
three.)
A.
by preserving interface and kernel information
B.
by reducing time of RE failover
C.
by preserving the data plane information
D.
by preserving the control plane information
E.
by not restarting the PFE
Answer: A,B,E
Explanation:
QUESTION NO: 17
Which protocol do multichassis link aggregation group (MC-LAG) devices use to exchange the
control information between two MC-LAG network devices?
A.
Virtual Chassis Control Protocol
B.
Multichassis Link Aggregation Protocol
C.
D.
Inter-chassis Control Protocol
Answer: D
Explanation:
QUESTION NO: 18
Which two statements are true about unified ISSU? (Choose two.)
A.
It allows gradual implementation of new features.
B.
It reduces operating costs while delivering higher service levels.
C.
It involves network down time during software image upgrades.
D.
It requires graceful Routing Engine switchover (GRES) and nonstop active routing (NSR).
Answer: B,D
Explanation:
QUESTION NO: 19
A.
nonstop active routing
B.
root protection
C.
nonstop forwarding
D.
Answer: C
Explanation:
QUESTION NO: 20
You have a router with dual Routing Engines. You want to ensure that your users experience
minimum downtime. You have decided to enable graceful Routing Engine switchover on the
router.
A.
{master}
jbase : 11.4R2
jcrypto: 11.4R2
jdocs : 11.4R2
jkernel: 11.4R2
jpfe : M40-11.4R2
jroute : 11.4R2
B.
{backup}
Graceful switchover: On
C.
{backup}
jbase : 11.4R2
jcrypto: 11.4R2
jdocs : 11.4R2
jkernel: 11.4R2
jpfe : M40-11.4R2
jroute : 11.4R2
D.
{master}
Graceful switchover: On
Answer: B
Explanation:
QUESTION NO: 21
Which OSPF LSA type is sent from the ABR to describe an ASBR that is in an area to which it is
connected?
A.
Type 7
"Pass Any Exam. Any Time." - www.actualtests.com 13
Juniper JN0-360 Exam
B.
Type 5
C.
Type 4
D.
Type 3
Answer: C
Explanation:
QUESTION NO: 22
A.
The BDR advertises link-state information with all other OSPF routers on the segment.
B.
The BDR forms an adjacency with all other OSPF routers on the segment.
C.
The BDR is ready to assume the role of the DR device if it fails.
D.
The BDR functions can be distributed to the DR device on the segment.
Answer: B,C
Explanation:
QUESTION NO: 23
Which OSPF adjacency state is reached when a hello packet has been sent, but bidirectional
communication has not been established?
A.
Down
B.
Init
D.
ExStart
Answer: B
Explanation:
QUESTION NO: 24
A.
The MTU is mismatched.
B.
The subnet mask is mismatched.
C.
The interface type is point-to-point.
D.
The interface type is broadcast.
Answer: C
Explanation:
QUESTION NO: 25
A.
backbone area
B.
not-so-stubby area
C.
stub area
Answer: A,B
Explanation:
QUESTION NO: 26
Which LSA packet types are originated only by an OSPF ABR router?
A.
Type 2 and Type 3
B.
Type 3 and Type 4
C.
Type 5 and Type 6
D.
Type 6 and Type 7
Answer: B
Explanation:
QUESTION NO: 27
In an OSPF environment, which two configuration parameters are used to determine which router
is the DR? (Choose two.)
A.
the router with the highest priority
B.
the router with the lowest priority
C.
the router with the highest RID
D.
the router with the lowest RID
QUESTION NO: 28
You have entered the show ospf route command and see routes with a metric type of EXT2.
A.
These routes are OSPF interarea routes.
B.
These routes have been redistributed into OSPF and are using a Type 2 metric.
C.
These routes are preferred over the same routes with an EXT1 metric.
D.
These routes are OSPF intra-area routes.
Answer: B
Explanation:
QUESTION NO: 29
You want to verify the frequency and type of SPF calculations on your Junos device.
A.
show ospf database | match log
B.
show spf log
C.
show ospf log
D.
show ospf statistics
"Pass Any Exam. Any Time." - www.actualtests.com 17
Juniper JN0-360 Exam
Answer: C
Explanation:
QUESTION NO: 30
You are troubleshooting an OSPF adjacency that is stuck in the ExStart state.
A.
Look for a mismatched IP subnet or mask.
B.
Determine whether the neighbor is a DR-Other.
C.
Determine whether the hello and dead intervals are the same on both sides.
D.
Review the MTU settings to ensure that they match.
Answer: D
Explanation:
QUESTION NO: 31
A.
Create a redistribution policy and apply it as an export policy under the [edit protocols ospf area]
hierarchy.
B.
Create a redistribution policy and apply it as an import policy in the [edit protocols ospf] hierarchy.
C.
Create a redistribution policy and apply it as an import or an export policy in the [edit protocols
ospf] hierarchy.
Answer: D
Explanation:
QUESTION NO: 32
You are configuring OSPF on a Junos device; however, you have not configured a router ID.
A.
If the loopback is configured with a 127/8 address, it will be used.
B.
If the loopback is not configured, it will use the interface with the highest IP address.
C.
If the loopback is configured and does not have a usable address, the IP address associated with
the first hardware interface is used.
D.
If you configure a dedicated management address and include that interface in OSPF, it will be
used as the router ID.
Answer: C
Explanation:
QUESTION NO: 33
A.
Level 1 adjacencies can form in the same (intra) area only.
B.
Level 2 adjacencies are formed between (inter) areas only.
C.
D.
Level 2 adjacencies can form within the same (intra) area only.
Answer: A,C
Explanation:
QUESTION NO: 34
A.
the complete sequence number PDU
B.
the partial sequence number PDU
C.
a hello PDU with a request PDU TLV specifying the missing LSP
D.
a hello PDU with a refresh PDU TLV requesting all LSPs
Answer: B
Explanation:
QUESTION NO: 35
Which statement is true regarding the IS-IS designated intermediate system (DIS)?
A.
The DIS function is used only on broadcast or multi-access networks.
B.
The DIS function is used on both broadcast and point-to-point link types.
C.
On a broadcast network, adjacencies are formed only between the non-DIS nodes and the DIS to
help reduce adjacency overhead.
Answer: A
Explanation:
QUESTION NO: 36
You want to establish an IS-IS Level 1 adjacency between two routers. The adjacency is not
forming.
Which three reasons would account for this issue? (Choose three.)
A.
A lack of or a malformed ISO network entity title (NET) on the loopback interface would cause this
issue.
B.
The interface MTU might be less than 1492.
C.
The IS-IS protocol on the loopback interface has not been enabled.
D.
The area IDs might be matched and should be set differently.
E.
An ISO NET might not be configured on the physical interface.
Answer: A,B,C
Explanation:
QUESTION NO: 37
Which three statements are true regarding the IS-IS link-state database (LSDB)? (Choose three.)
A.
An L1 router has a single database reflecting the connectivity of its area.
B.
C.
The Level 2 database contains only backbone area routes unless route leaking is configured.
D.
Route leaking can be used to optimize Level 2 to Level 1 routing.
E.
An attached router has at least two LSDBs: one for each Level 1 area and a single LSDB for the
Level 2 backbone.
Answer: A,B,E
Explanation:
QUESTION NO: 38
Which PDU type is sent by an IS-IS router when it detects that its link-state database is out of
date?
A.
hello
B.
link state
C.
complete sequence number
D.
partial sequence number
Answer: D
Explanation:
QUESTION NO: 39
What are two similarities between OSPF and IS-IS? (Choose two.)
A.
B.
Both use the Dijkstra algorithm to construct a shortest-path tree.
C.
Both elect a designated router and a backup designated router.
D.
Both have a built-in mechanism to provide address summarization between areas.
Answer: A,B
Explanation:
QUESTION NO: 40
Which three statements correctly describe IBGP and EBGP interaction? (Choose three.)
A.
IBGP is used within an AS, whereas EBGP is used between two different ASs.
B.
EBGP peering is normally loopback-based to provide tolerance for interface or link failures.
C.
By default, EBGP updates the next-hop attribute, whereas IBGP does not.
D.
IBGP speakers can re-advertise IBGP-learned or EBGP-learned routes to other IBGP speakers.
E.
EBGP speakers can re-advertise IBGP-learned or EBGP-learned routes to other EBGP speakers.
Answer: A,C,E
Explanation:
QUESTION NO: 41
Which two statements correctly describe how the AS path attribute is used by BGP? (Choose
two.)
B.
The AS path attribute is updated in EBGP advertisements only and is the primary loop-avoidance
mechanism for BGP.
C.
When local preference is the same, the AS path attribute is a common tiebreaker, where paths
with fewer AS hops are preferred.
D.
When local preference is the same, the AS path attribute is a common tiebreaker, where paths
with more AS hops are preferred.
Answer: B,C
Explanation:
QUESTION NO: 42
Which statement describes the role of local preference in the BGP route selection process?
A.
Local preference is evaluated early in the BGP route selection process and results in the route
with the highest numerical local preference being selected.
B.
Local preference is evaluated early in the BGP route selection process and results in the route
with the lowest numerical local preference being selected.
C.
Local preference is used to break ties when all other received BGP attributes are otherwise equal.
D.
Local preference is sent by an EBGP speaker to a neighboring AS in an attempt to influence how
the remote peer's traffic will ingress into your network.
Answer: A
Explanation:
QUESTION NO: 43
A.
AS path
B.
originator ID
C.
next hop
D.
cluster list
E.
origin
Answer: A,B,D
Explanation:
QUESTION NO: 44
You are attempting to influence return traffic into your autonomous system by preferring one router
as an entry point.
Which two BGP attributes will affect this behavior? (Choose two.)
A.
originator ID
B.
local preference
C.
AS path
D.
MED
Answer: C,D
Explanation:
Which three BGP attributes must be sent to EBGP peers? (Choose three.)
A.
local preference
B.
atomic aggregator
C.
origin
D.
next hop
E.
AS path
Answer: C,D,E
Explanation:
QUESTION NO: 46
A.
OpenEstablished
B.
OpenConnect
C.
OpenConfirm
D.
OpenActive
Answer: C
Explanation:
A.
Using BGP within your AS eliminates the need for an IGP.
B.
EBGP sessions have a TTL value of 64 by default.
C.
If an EBGP peer is more than one hop away, a multihop BGP session must be established.
D.
BGP devices require a direct connection to peer with each other.
Answer: C
Explanation:
QUESTION NO: 48
A route to the same destination is received from two different BGP sources.
A.
cluster length
B.
AS-path length
C.
lowest RID
D.
local preference
Answer: D
Explanation:
QUESTION NO: 49
"Pass Any Exam. Any Time." - www.actualtests.com 27
Juniper JN0-360 Exam
You are troubleshooting a BGP-learned prefix that is not being installed in the routing table.
A.
show route advertising-protocol bgp
B.
show route state
C.
show route hidden extensive
D.
show bgp summary
Answer: C
Explanation:
QUESTION NO: 50
You are asked to configure a new external BGP connection to a peer's loopback interface. You
verify that the peer's loopback interface is reachable, but the BGP connection remains in Idle
state.
A.
multipath
B.
multihop
C.
as-override
D.
advertise-inactive
Answer: B
Explanation:
QUESTION NO: 51
Which two statements are true about virtual switches? (Choose two.)
A.
Multiple virtual switches share a single MAC table.
B.
Virtual switches contain separate MAC tables.
C.
By default, the direct route associated with a virtual switch's IRB interface is placed in inet.0.
D.
By default, the direct route associated with a virtual switch's IRB interface is placed in the
associated virtual switch's routing table.
Answer: B,C
Explanation:
QUESTION NO: 52
A.
pop the outer tag and swap the inner tag
B.
pop and swap the inner tag
C.
pop and swap both outer and inner tags
D.
pop the inner tag and swap the outer tag
Answer: A
Explanation:
What are three components of the tag portion of an 802.1Q-tagged Ethernet frame? (Choose
three.)
A.
Tag Protocol Identifier
B.
maximum transmission unit
C.
canonical format indicator
D.
unique VLAN identifier
E.
frame check sequence
Answer: A,C,D
Explanation:
QUESTION NO: 54
Which three mechanisms are used by switches to build and maintain bridge tables? (Choose
three.)
A.
learning
B.
rewriting
C.
flooding
D.
aging
E.
blocking
Answer: A,C,D
QUESTION NO: 55
A.
to carry traffic for multiple VLANs between multiple switches
B.
to interconnect multiple bridging domains on the same switch
C.
to aggregate multiple native VLANs into a single bridging domain
D.
to allow Layer 3 functionality for multiple VLANs
Answer: A
Explanation:
QUESTION NO: 56
What are two differences between RSTP and VSTP? (Choose two.)
A.
Using VSTP, the BPDU destination address is always 01:00:0C:CC:CC:CD.
B.
Using VSTP, the BPDU frame carries an 802.1Q tag.
C.
Using RSTP, the BPDU destination address is always 01:00:0C:CC:CC:CD.
D.
Using RSTP, the BPDU frame carries an 802.1Q tag.
Answer: A,B
Explanation:
QUESTION NO: 57
A rogue switch has been added to your network, exchanged BPDUs, and is now part of the
spanning tree topology.
Which feature would help prevent this from happening in the future?
A.
storm control
B.
BPDU control
C.
root protection
D.
loop protection
Answer: B
Explanation:
QUESTION NO: 58
A.
32
B.
64
C.
128
D.
256
Answer: B
Explanation:
QUESTION NO: 59
Which two statements are true about STP and RSTP? (Choose two.)
A.
STP uses a proposal-and-agreement handshake on point-to-point links instead of timers.
B.
In RSTP, root ports and edge ports transition to the forwarding state immediately, without
exchanging messages with other switches.
C.
In RSTP, a TCN is generated when a port transitions to the discarding state.
D.
In STP, the forwarding delay timer and maximum age timer define the convergence delay.
Answer: B,D
Explanation:
QUESTION NO: 60
What are two types of BPDUs in the Spanning Tree Protocol? (Choose two.)
A.
configuration
B.
hello
C.
topology change notification
D.
link state
Answer: A,C
Explanation:
You are asked to establish an MPLS LSP between two sites. You are required to ensure the LSP
traverses specific routers within your network.
A.
Enable traffic engineering within LDP and define the explicit route the LSP must follow.
B.
Implement RSVP and define the explicit route the LSP must follow.
C.
Enable traffic engineering within RSVP and define the explicit route the LSP must follow.
D.
Implement LDP and define the explicit route the LSP must follow.
Answer: B
Explanation:
QUESTION NO: 62
A.
MPLS creates a copy of the mpls.0 table and stores it in the inet.3 routing table.
B.
The inet.3 routing table is used by transit routers to identify label values.
C.
BGP can use the inet.3 routing table to resolve next hops.
D.
MPLS uses the inet.3 routing table to assign labels.
Answer: C
Explanation:
Which two statements are correct about default MPLS behavior on Junos devices? (Choose two.)
A.
The MPLS label is popped by the penultimate router.
B.
The MPLS label is popped by the ultimate router.
C.
The MPLS label is pushed by the ingress router.
D.
The MPLS label is swapped by the ingress router.
Answer: A,C
Explanation:
QUESTION NO: 64
Which two statements regarding the MPLS label information base are correct? (Choose two.)
A.
The MPLS label information base is stored in the inet.3 table.
B.
The MPLS label information base is stored in the mpls.0 table.
C.
The label information base is used by all LSRs to forward LSP traffic.
D.
The label information base is used by transit LSRs to forward LSP traffic.
Answer: B,D
Explanation:
QUESTION NO: 65
Which two statements are correct about RSVP path messages? (Choose two.)
B.
They are sent by the ingress router downstream.
C.
They are used to create an LSP.
D.
They are used to reserve resources for an LSP.
Answer: B,C
Explanation:
QUESTION NO: 66
Which two statements are correct regarding LDP-signaled VPLS instances? (Choose two.)
A.
You must enable the Layer 2 VPN signaling NLRI.
B.
You must configure the same VPLS identifier on all peers.
C.
You must define a the same site-identifier value on all peers.
D.
You must define all neighbors using their tunnel end-point IP addresses.
Answer: B,D
Explanation:
QUESTION NO: 67
Which two statements are correct regarding LDP-signaled Layer 2 circuits? (Choose two.)
A.
You must enable the Layer 2 VPN signaling NLRI.
C.
You must specify the neighbor using the tunnel end-point IP address.
D.
You must define a unique site-identifier value.
Answer: B,C
Explanation:
QUESTION NO: 68
Which two statements are correct regarding BGP-signaled Layer 2 VPNs? (Choose two.)
A.
You must enable the Layer 2 VPN signaling NLRI.
B.
You must configure the virtual circuit identifier.
C.
You must specify the neighbor using the tunnel end-point IP address.
D.
You must define a unique site-identifier value.
Answer: A,D
Explanation:
QUESTION NO: 69
Which two statements regarding VRF tables are correct? (Choose two.)
A.
A PE router's VRF table stores routes received from directly connected CE devices.
B.
A PE router's VRF table stores routes received from its IGP from remote PE devices.
D.
A PE router's VRF table stores routes received from all P and PE devices within the same AS.
Answer: A,C
Explanation:
QUESTION NO: 70
You have been asked to implement routing policy on the PE devices in your AS and to ensure the
correct customer routes are installed in the appropriate VRF tables.
A.
BGP communities
B.
VLAN IDs
C.
route distinguisher
D.
circuit IDs
Answer: A
Explanation:
QUESTION NO: 71
A.
The community value is used to identify routes that should be imported by remote PEs.
B.
The community value is used to determine valid remote devices when signaling a Layer 3 VPN.
D.
The community value is used to determine transit devices when signaling a Layer 3 VPN.
Answer: A
Explanation:
QUESTION NO: 72
You have been asked to deploy a Layer 2 VPN for a new customer.
What information will be present in the PE's associated VPN forwarding table? (Choose three.)
A.
the customer site ID
B.
the route distinguisher
C.
the interface encapsulation
D.
the label base
E.
the community name
Answer: A,C,D
Explanation:
QUESTION NO: 73
You have an established Layer 3 VPN where you are using static routing between your PE and
CE devices. You must advertise their directly connected subnet to remote PE devices.
B.
Use the VRF table label.
C.
Use a VRF export policy.
D.
Use a route distinguisher.
Answer: B,C
Explanation:
QUESTION NO: 74
You have been asked to verify the state of an LDP-signaled Layer 2 circuit.
Which two commands would you use to verify the state of the connection? (Choose two.)
A.
show mpls lsp
B.
show l2circuit connections
C.
show l2circuit statistics
D.
show ldp database
Answer: B,D
Explanation:
QUESTION NO: 75
A.
"Pass Any Exam. Any Time." - www.actualtests.com 40
Juniper JN0-360 Exam
2bfc::02 :0:0:fe c:5c
B.
2bfc::2 ::fe c:5c
C.
2bfc:2 :0:0:fe c:5c
D.
2bfc:0:0:2 ::fe c:5c
Answer: A,D
Explanation:
QUESTION NO: 76
Which new field is added to the IPv6 header when compared to IPv4?
A.
version
B.
fragment offset
C.
checksum
D.
flow label
Answer: D
Explanation:
QUESTION NO: 77
A.
multicast header
B.
C.
autoconfiguration options
D.
fragment
E.
hop-by-hop options
Answer: B,D,E
Explanation:
QUESTION NO: 78
What are two components of an IPv6 router advertisement message? (Choose two.)
A.
DHCPv6 request
B.
Layer 2 address of advertising router
C.
duplicate address detection notification
D.
link MTU
Answer: B,D
Explanation:
QUESTION NO: 79
Which two statements are correct about neighbor discovery in IPv6? (Choose two.)
A.
Neighbor discovery relies on ARP to find neighbors on a local link.
B.
C.
A neighbor is considered reachable when the neighboring device responds to a router solicitation
message.
D.
Neighbor discovery does not use ARP to find neighbors on a local link.
Answer: B,D
Explanation:
QUESTION NO: 80
You want to configure an interface on your router to use an IPv6 global IP address.
A.
Use stateless autoconfiguration to assign only the 64 bit interface ID.
B.
Use stateful autoconfiguration to assign only the 64 bit interface ID.
C.
Use stateful autoconfiguration to assign the entire global IPv6 address.
D.
Use a statically assigned global IPv6 address.
E.
Use stateless autoconfiguration to assign the entire global IPv6 address
Answer: A,C,D
Explanation:
QUESTION NO: 81
Which two support tunneling for non-IP protocols on Junos devices? (Choose two.)
B.
GRE
C.
IP-IP
D.
ATM AAL1
Answer: B,C
Explanation:
QUESTION NO: 82
Which two support the tunneling of IP traffic on Junos devices? (Choose two.)
A.
ATM AAL2
B.
GRE
C.
IP-IP
D.
ATM AAL1
Answer: B,C
Explanation:
QUESTION NO: 83
Which two statements are true regarding GRE tunnels? (Choose two.)
A.
GRE can be used to tunnel IP packets only.
C.
GRE tunnels can be used to send nonroutable packets over a public IP network.
D.
GRE tunnels can be used as backup links.
Answer: C,D
Explanation:
QUESTION NO: 84
Which two statements are true regarding GRE tunnel overhead? (Choose two.)
A.
If the host sends a packet larger than the MTU, that packet must be dropped.
B.
Packets are not dropped because the router clears the DF bit for GRE traffic by default.
C.
Packets larger than the MTU are fragmented or dropped depending on the DF bit setting.
D.
You can change the tunnel MTU to avoid packet fragmentation or drops.
Answer: C,D
Explanation:
QUESTION NO: 85
-- Exhibit --
StatE.
AgE. 1:03:46
Task: Aggregate
AS path: I
-- Exhibit --
You are advertising the route in the exhibit to your OSPF neighbors.
A.
The default route will remain active and will "blackhole" all traffic from your OSPF peers.
B.
The default route will become unavailable and will no longer be advertised to your OSPF peers.
C.
The default route will remain active and will continue to be advertised to your OSPF peers.
D.
The default route will become unavailable and will continue to be advertised to your OSPF peers.
Answer: B
Explanation:
QUESTION NO: 86
-- Exhibit --
[edit policy-options]
user@router# show
policy-statement load-balance {
from {
then {
load-balance per-packet;
-- Exhibit --
Referring to the exhibit, which configuration correctly applies the load-balancing policy?
A.
[edit routing-options]
user@router# show
forwarding-options {
export load-balance;
B.
[edit routing-options]
static {
export load-balance;
C.
[edit routing-options]
user@router# show
forwarding-table {
export load-balance;
D.
[edit routing-options]
user@router# show
routing-table {
export load-balance;
Answer: C
Explanation:
QUESTION NO: 87
-- Exhibit --
[edit]
rib-groups {
test {
-- Exhibit --
Referring to the exhibit, what is the result of the RIB group configuration?
A.
All routes from the walter.inet.0 and the nancy.inet.0 routing tables will be imported into the default
master routing instance.
B.
Routes from the walter.inet.0 routing table will be imported into the nancy.inet.0 routing table.
C.
All routes will be shared between the walter.inet.0 and the nancy.inet.0 routing tables.
D.
Routes from the nancy.inet.0 routing table will be imported into the walter.inet.0 routing table.
Answer: B
Explanation:
QUESTION NO: 88
-- Exhibit --
{master}[edit]
RE modE. Master
OSPF Complete
RIP Complete
BGP Complete
MPLS Complete
{master}[edit]
{backup}[edit]
Graceful switchover: On
{backup}[edit]
{backup}[edit]
Synchronization master:
-- Exhibit --
A.
An RE switchover is likely to result in BGP disruption, but no dataplane impact will be seen.
B.
An RE switchover is likely to result in BGP disruption which will also effect the dataplane.
C.
The system is not yet GRES ready, you need to wait for kernel synchronization to complete.
D.
The system is NSR ready and a switchover should be hitless to the BGP control and data plane.
Answer: D
Explanation:
QUESTION NO: 89
-- Exhibit --
{master}[edit]
RE modE. Master
OSPF Complete
RIP Complete
BGP Complete
MPLS Complete
LDP Complete
{master}[edit]
inet.0: 0/0/0/0
inet.2: 0/0/0/0
bgp.l3vpn.0: 0/0/0/0
...
{backup}[edit]
Graceful switchover: On
{backup}[edit]
-- Exhibit --
You have been asked to determine if an NSR switchover will be hitless for a given BGP peer.
A.
The BGP session is idle on the backup RE indicating that the session will flap at switchover.
B.
The task replication process has completed on the master indicating a hitless switchover can be
expected.
C.
The GRES synchronization process is underway and must complete before the protocol state can
be checked.
Answer: A
Explanation:
QUESTION NO: 90
-- Exhibit --
unit 0 {
family inet {
address 10.100.1.1/24 {
vrrp-group 1 {
virtual-address 10.200.12.254;
priority 150;
accept-data;
track {
interface ge-1/0/0 {
priority-cost 40;
unit 0 {
address 10.100.1.2/24 {
vrrp-group 1 {
virtual-address 10.200.12.254;
accept-data;
-- Exhibit --
Referring to the exhibit, which two statements are correct about the configuration? (Choose two.)
A.
R2 is the backup router and will become the master router if ge-1/0/0 on R1 goes down.
B.
R2 is the backup router and will remain the backup router if ge-1/0/0 on R1 goes down.
C.
If R1 goes down, R2 will become the master and will relinquish mastership once R1 comes back
online.
D.
If R1 goes down, R2 will become the master and will remain the master once R1 comes back
online.
Answer: B,C
Explanation:
QUESTION NO: 91
interfaces {
ge-1/0/3 {
unit 0 {
family inet {
address 192.168.1.1/30;
ge-1/1/0 {
unit 0 {
family inet {
address 10.100.10.1/30;
fxp0 {
unit 0 {
family inet {
address 10.2.1.13/28;
lo0 {
unit 0 {
family inet {
address 10.100.1.1/32;
protocols {
ospf {
area 0.0.0.0 {
interface ge-1/0/3.0;
interface ge-1/1/0.0;
-- Exhibit --
A.
192.168.1.1
B.
10.100.1.1
C.
127.0.0.1
D.
10.2.1.13
Answer: B
Explanation:
QUESTION NO: 92
-- Exhibit --
protocols {
isis {
level 1 disable;
interface ge-1/0/0.0 {
level 2 disable;
interface ge-1/1/0.0;
interface lo0.0;
-- Exhibit --
A.
Level 1 is enabled.
B.
Level 1 is disabled.
C.
Level 2 is enabled.
D.
Level 1 and Level 2 are disabled.
Answer: A
Explanation:
-- Exhibit --
[edit]
-- Exhibit --
Referring to the exhibit, which two statements are true regarding the GE interface? (Choose two.)
A.
It operates at both Level 1 and Level 2.
B.
It operates at Level 3, which supports hierarchical backbone areas.
C.
The local router is the IS-IS designated intermediate system at all levels.
D.
The local router is the IS-IS designated router at all levels.
Answer: A,C
Explanation:
QUESTION NO: 94
-- Exhibit --
user@R2> show
protocols {
isis {
"Pass Any Exam. Any Time." - www.actualtests.com 58
Juniper JN0-360 Exam
export leak;
interface ge-1/1/0.0;
interface ge-1/1/1.0 {
level 1 disable;
interface lo0.0;
policy-options {
policy-statement leak {
term 1 {
from level 1;
to level 2;
then accept;
-- Exhibit --
R1 and R2 have a Level 1 IS-IS adjacency. R2 participates in both Level 1 and Level 2, and is
receiving routes from a Level 2 neighbor. A policy on R2 has been created to leak routes to Level
1, but R1 is not receiving the routes.
A.
The policy must be applied as an export policy at the interface level.
B.
The policy must be changed to include from protocol isis.
D.
The policy must be applied as an import policy.
Answer: C
Explanation:
QUESTION NO: 95
-- Exhibit --
user@R1> show
interfaces {
ge-1/1/0 {
unit 0 {
family inet {
address 10.100.1.1/30;
family iso;
lo0 {
unit 0 {
family inet {
address 10.100.10.1/32;
family iso {
address 49.1001.0010.0100.00;
protocols {
isis {
interface ge-1/1/0.0 {
level 2 disable;
interface lo0.0;
user@R2> show
interfaces {
ge-1/1/0 {
unit 0 {
family inet {
address 10.100.1.2/30;
lo0 {
unit 0 {
family inet {
address 10.100.10.2/32;
family iso {
address 49.1001.0010.0200.00;
protocols {
isis {
interface ge-1/1/0.0;
interface lo0.0;
-- Exhibit --
Referring to the exhibit, R1 and R2 are directly connected using interface ge-1/1/0.
A.
No adjacency forms
B.
Level 2 adjacency forms
C.
Level 1 adjacency forms
D.
Level 1 and Level 2 adjacencies form
Answer: C
Explanation:
QUESTION NO: 96
user@R1> show
interfaces {
ge-1/1/0 {
unit 0 {
family inet {
address 10.100.1.1/30;
family iso;
lo0 {
unit 0 {
family inet {
address 10.100.10.1/32;
family iso {
address 49.1001.0010.0100.00;
protocols {
isis {
level 1 disable;
interface ge-1/1/0.0 {
level 2 disable;
interface lo0.0;
user@R2> show
interfaces {
ge-1/1/0 {
unit 0 {
family inet {
address 10.100.1.2/30;
family iso {
mtu 1496;
lo0 {
unit 0 {
family inet {
address 10.100.10.2/32;
family iso {
address 49.1002.0010.0200.00;
isis {
interface ge-1/1/0.0 {
level 2 disable;
interface lo0.0;
-- Exhibit --
Referring to the exhibit, R1 and R2 are directly connected using interface ge-1/1/0.
A.
R2 has an MTU value of 1496 configured on ge-1/1/0.
B.
R2 and R1 have different area IDs.
C.
R1 is configured for Level 2, and R2 is configured for Level 1.
D.
R1 is configured for both Level 1 and Level 2 to be disabled.
Answer: B
Explanation:
QUESTION NO: 97
-- Exhibit --
[edit]
...
-- Exhibit --
Referring to the BGP peering sessions shown in the exhibit, which two statements are true?
(Choose two.)
A.
The peering session with the 10.1.1.1 neighbor is fully operational.
B.
The peering session with the 5.1.1.1 neighbor is fully operational.
C.
The local router peering with the 20.1.1.1 neighbor is waiting for a start event.
D.
The local router peering with the 20.1.1.1 neighbor is waiting for a BGP refresh message.
Answer: B,C
Explanation:
QUESTION NO: 98
-- Exhibit --
Table Tot Paths Act Paths Suppressed History Damp State Pending
0 0 0 0 0 0
-- Exhibit --
Two newly configured BGP peers have remained in the states shown in the exhibit for several
hours.
A.
The TCP three-way handshake has completed successfully with the 10.1.1.1 peer.
B.
The TCP three-way handshake has completed successfully with the 5.1.1.1 peer.
C.
The local router has received a BGP keepalive message from the 5.1.1.1 peer.
D.
The local router is initiating a transport protocol connection with the 10.1.1.1 peer.
Answer: B,D
Explanation:
QUESTION NO: 99
-- Exhibit --
Reject
49.0000.0020.0200.2002/72
[edit]
policy-statement adv-route {
term t1 {
from {
protocol isis;
then accept;
term t2 {
then reject;
[edit]
group ebgp {
type external;
export adv-route;
neighbor 192.168.12.1 {
peer-as 65000;
-- Exhibit --
Referring to the exhibit, why is the 200.1.0.0/16 prefix failing to be advertised in BGP?
A.
"Pass Any Exam. Any Time." - www.actualtests.com 69
Juniper JN0-360 Exam
BGP needs a next-hop self policy.
B.
The aggregate route is set to reject.
C.
The policy works for internal BGP only.
D.
The IS-IS route is less preferred than the aggregate route.
Answer: D
Explanation:
-- Exhibit –
-- Exhibit --
You are asked to configure a new external BGP peering. You have configured BGP on R1 as
shown in the exhibit, however the BGP peering remains in Active state.
B.
Configure the BGP type as external.
C.
Remove the local-as statement.
D.
Remove the autonomous-system statement.
Answer: C
Explanation:
-- Exhibit --
AS path: 65001 I
AS path: 65001 I
AS path: 65001 I
AS path: 65001 I
Restart Complete
Reject
Reject
Reject
Reject
Reject
export export-200;
group c5 {
neighbor 192.168.100.2 {
export export-200.200;
peer-as 65002;
from {
then accept;
term 1 {
from {
then accept;
-- Exhibit --
R2 is exporting static routes to R1 using BGP. R1 is not receiving one of the five static routes that
is configured on R2.
Referring to the exhibit, what should be changed under the BGP configuration to resolve this
issue?
A.
Delete the global export policy.
B.
Delete the neighbor export policy.
C.
Move policy export-200 to the group level.
D.
Move policy export-200.200 to the group level.
-- Exhibit --
unit 0 {
family inet {
address 192.168.100.1/30;
autonomous-system 65001;
group 65002 {
traceoptions {
file bgp-trace;
neighbor 192.168.100.3 {
peer-as 65002;
20:45:44.212833 Out
Device Media Type Extension TLV #3, length 1, valuE. Ethernet (1)
Logical Interface Encapsulation Extension TLV #6, length 1, valuE. Ethernet (14)
-----original packet-----
80:71:1f:c7:f8:60 > 84:18:88:8e:3b:3f, ethertype 802.1Q (0x8100), length 82: vlan 435, p 6,
ethertype IPv4, (tos 0xc0, ttl 255, id 19548, offset 0, flags [DF], proto: TCP (6), length: 64)
192.168.100.1.bgp > 192.168.100.2.49373: S 1088527795:1088527795(0) ack 214564428 win
16384
20:45:44.213226 In
Juniper PCAP Flags [Ext, no-L2, In], PCAP Extension(s) total length 22
Device Media Type Extension TLV #3, length 1, valuE. Ethernet (1)
Logical Interface Encapsulation Extension TLV #6, length 1, valuE. Ethernet (14)
-----original packet-----
PFE proto 2 (ipv4): (tos 0xc0, ttl 1, id 2367, offset 0, flags [none], proto: TCP (6), length: 52)
192.168.100.2.49373 > 192.168.100.1.bgp: . 1:1(0) ack 1 win 17376
-- Exhibit --
"Pass Any Exam. Any Time." - www.actualtests.com 75
Juniper JN0-360 Exam
Click the Exhibit button.
You are asked to configure an EBGP peering to AS 65002. The EBGP peering is stuck in a
Connect state.
Referring to the exhibit, what should be changed to the BGP configuration to bring up the peering?
A.
Configure the neighbor to 192.168.100.2.
B.
Configure the local-as to 65001.
C.
Configure the peer-as to 65001.
D.
Configure the peering as passive.
Answer: A
Explanation:
-- Exhibit --
autonomous-system 65001;
group 65002 {
traceoptions {
file bgp-trace;
neighbor 192.168.100.2 {
peer-as 65002;
Feb 5 20:08:23.478040
Feb 5 20:08:23.478217 BGP SEND 4 Byte AS-Path capability (65), as_num 65001
Feb 5 20:08:23.478820
Feb 5 20:08:23.478974 BGP RECV 4 Byte AS-Path capability (65), as_num 65003
Feb 5 20:08:23.479104
Feb 5 20:08:23.479156 BGP SEND Notification code 2 (Open Message Error) subcode 2 (bad
peer AS number)
-- Exhibit --
You have been asked to configure an EBGP peering to AS 65002. The EBGP peering is stuck in
an Active state.
A.
Configure the local-as to 65003.
B.
Configure the autonomous-system to 65003.
C.
Configure the EBGP peering as passive.
D.
Configure the peer-as to 65003.
Answer: D
Explanation:
-- Exhibit –
-- Exhibit --
In the exhibit, A1 sends a broadcast frame with destination MAC address FFFF.FFFF.FFFF, and
all other stations have sent a response .
ge-0/0/0 0140.5501.1111
A.
ge-0/0/0 FFFF.FFFF.FFFF
B.
ge-0/0/0 FFFF.FFFF.FFFF
C.
ge-0/0/0 0140.5501.2222
ge-0/0/1 0140.5501.3333
ge-0/0/1 0140.5501.4444
ge-0/0/0 0140.5501.1111
D.
ge-0/0/0 0140.5501.2222
ge-0/0/1 0140.5501.3333
ge-0/0/1 0140.5501.4444
Answer: D
"Pass Any Exam. Any Time." - www.actualtests.com 79
Juniper JN0-360 Exam
Explanation:
-- Exhibit –
-- Exhibit --
In the exhibit, all switches run STP; however, the link between bridge G and bridge E fails.
What does root bridge A do after it receives information about this link failure?
A.
Root bridge A sets the acknowledge flag and sends an updated topology BPDU.
B.
Root bridge A sends a topology change notification BPDU.
"Pass Any Exam. Any Time." - www.actualtests.com 80
Juniper JN0-360 Exam
C.
Root bridge A sets the topology change flag and sends an updated configuration BPDU.
D.
Root bridge A floods an updated BPDU topology database.
Answer: C
Explanation:
-- Exhibit –
-- Exhibit --
Referring to the exhibit, you have an established RSVP LSP between R1 and R5 when you
experience a link failure between R2 and R4.
A.
R2 sends a ResvTear message upstream to R1 signaling the link failure.
B.
R2 sends a PathTear message upstream to R1 signaling the link failure.
C.
R4 sends a ResvTear message downstream to R5 signaling the link failure.
D.
R4 sends a PathTear message downstream to R5 signaling the link failure.
Answer: A,D
-- Exhibit --
[edit]
group ibgp {
type internal;
local-address 3.3.3.3;
family inet;
neighbor 2.2.2.2;
[edit]
VRF {
instance-type vrf;
interface xe-0/0/1.0;
route-distinguisher 3.3.3.3:100;
vrf-target target:100:100;
vrf-table-label;
[edit]
interface all;
[edit]
interface all;
-- Exhibit --
Referring to the exhibit, what is missing in the configuration to make the Layer 3 VPN functional?
(Choose two.)
A.
a label-switched path
B.
the LDP protocol configuration
C.
a virtual circuit ID
D.
an NLRI of family inet-vpn unicast
Answer: A,D
Explanation:
-- Exhibit --
xe-0/0/0 {
unit 0 {
family inet {
address 192.168.12.1/24;
family mpls;
xe-0/0/1 {
encapsulation ethernet-ccc;
unit 0 {
family ccc;
lo0 {
unit 0 {
family inet {
address 1.1.1.1/32;
[edit]
mpls {
interface all;
ospf {
traffic-engineering;
area 0.0.0.0 {
interface all;
ldp {
interface all;
l2circuit {
neighbor 2.2.2.2 {
interface xe-0/0/1.0 {
-- Exhibit --
In the exhibit, which configuration element is missing to bring up the Layer 2 circuit?
A.
the route target
B.
the virtual circuit ID
C.
a targeted LDP session
D.
an MPLS LSP
Answer: B
Explanation:
-- Exhibit –
-- Exhibit --
Based on the exhibit, which configuration will permit end-to-end routing through the GRE tunnel for
R1?
A.
[edit]
B.
[edit]
C.
[edit]
D.
[edit]
Answer: C
Explanation:
Topic 2, Volume B
What are two valid actions that can be applied to a frame by a Layer 2 firewall filter?
(Choose two)
A.
Log
B.
loss-priority
C.
sample
D.
count
Answer: B,D
Explanation:
You can specify the following filter actions:
* accept
* count counter-name
* discard
* forwarding-class class-name
* next term
* policer policer-name
* three-color-policer policer-name
Which two statements describe differences between IPv4 and IPv6? (Choose two)
A.
IPsec is built into IPv6
B.
IPv6 uses a 32-bit (4-byte) address and can support up to 4,294,967,296 addresses
C.
IPv4 supports extension headers whereas IPv6 options are integrated into the base
D.
IPv6 eliminates the need for NAT
Answer: A,D
You must configure an OSPF area that does not accept type 3 link-state advertisements (LSAs)
from area 0 (other than the default route) You have configured your area to be stub, but you still
see type 3 LSAs.
A.
You should have configured your area as totally stubby
B.
You should have used a not-so-stubby-area
C.
You are experiencing a routing loop
D.
You have exported routes into OSPF
Answer: A
Explanation:
Which Junos operational mode command is used to verify that the tunnel interface is up and
operational?
A.
show chassis tunnel status
B.
show tunnel interface
C.
show interfaces terse
Answer: C
Explanation:
A.
IIH
B.
LSP
C.
PSNP
D.
CSNP
Answer: A
Explanation:
Router A is an OSPF router connected to both Area 0 and Area 1 Area 1 has been configured as a
stub area Which two LSA types does Router A suppress from Area 1 ?
A.
Router LSA
B.
External LSA
C.
Summary LSA
D.
ASBR Summary LSA
You are logged into a router and have navigated to the (edit routing-options] level of the hierarchy.
You have been asked to create a static route that will use 10.10.10.1 as its primary next-hop and
10.10.10.5 as its secondary next-hop.
A.
set static route 8/8 10.10.10.1 qualified-next-hop 10.10.10.5 pref 10
B.
set static route 8/8 next-hop 10.10.10.1 secondary-next-hop 10.10.10.5 preference 10
C.
set static route 8/8 next-hop 10.10.10.1 qualified-next-hop 10.10.10.5 preference 10
D.
set static route 8/8 next-hop [10.10.10.1 10.10.10.5] pref 10
Answer: C
Explanation:
Which Junos operational mode command is used to verify that load balancing is working as
expected?
A.
show route all
B.
show route extensive
C.
show route balancing
D.
Answer: D
Explanation:
Based on the illustration of the VPLS topology shown in the exhibit, which statement is true?
A.
PE-C must have a spanning-tree protocol enabled
B.
CE-C must have BGP enabled
C.
Traffic forwarded from PE-C to PE-A is forwarded on to PE-B
D.
Traffic forwarded from PE-C to PE-A is not forwarded on to PE-B
Answer: D
Explanation:
Which two values displayed in the output from the show spanning-tree MSTP configuration
command must match on all switches participating in the same MSTP region? (Choose two)
A.
root bridge identifier
B.
authentication checksum
C.
context identifier
D.
configuration digest
Answer: C,D
Explanation:
Which role does the router ID (RID) have in the BGP route selection process?
A.
The router ID is evaluated immediately after MED to determine route preference
B.
The router ID is evaluated last in the route selection process
C.
The router ID is evaluated after the cluster length and a lower router ID is chosen
D.
The router ID is evaluated after analyzing the IGP metric cost
Answer: C
Reference:
http://www.juniper.net/techpubs/en_US/junos10.0/information-products/topic-collections/nog-
baseline/bgp-routes-and-selection-introduction.html
You are logged into a router and have navigated to the [edit routing-options] level of the hierarchy.
You have been asked to create a static route that will use 43 18 7 1 as its primary next-hop and 76
1310 2 as its secondary next-hop.
A.
set static route 0/0 76.13.10.2 qualified-next-hop 43.18.7.1 pref 10
B.
set static route 0/0 next-hop 43.18.7.1 secondary-next-hop 76.13.10.2 preference 10
C.
set static route 0/0 next-hop [76.13.10.2 10.10.10.5] pref 10
D.
set static route 0/0 next-hop 43.18.7.1 qualified-next-hop 76.13.10.2 preference 10
Answer: D
Explanation:
A.
Router A will use the routes from area 49.2222; it learns from router B
B.
Router A will see the attached bit from router B and create a default route
C.
Router A must have a default route manually configured
D.
Router A will receive a default route in the IS-IS update from router B
Answer: B
Explanation:
You have recently implemented a graceful Routing-Engine switchover (GRES) and want to further
reduce down time if a Routing Engine (RE) failure occurs.
Which two features can be configured on this device to reduce its downtime in this situation?
(Choose two)
A.
VRRP
B.
GR
C.
BFD
D.
NSR
Answer: B,D
Explanation:
A.
Established
B.
Active
C.
Operational
D.
Connect
Answer: A
Explanation:
You work for the regional Internet service provider shown in the exhibit You have a partial BGP
table and are receiving a 10 100/16 route from your upstream ISP You have been asked to
configure a default route that can be sent to your downstream customer This route should forward
customer traffic toward your upstream Tier 11SP as long as the 10.100/16 route is present.
A.
Create and announce an aggregate default route
C.
Create and announce a static default route with a next-hop of reject
D.
Create and announce a generated default route
E.
Create an advertise-map with exist-map
Answer: E
Reference:
http://www.juniper.fr/techpubs/en_US/junose10.0/information-products/topic-collections/swconfig-
bgp-mpls/advertising-a-default-route-only-when-another-route-is-present.html
In the exhibit, OSPF routers R1, R2, R3, and R4 come up, in order, at 1-minute intervals
B.
R2
C.
R3
D.
R4
Answer: A
Explanation:
You have been asked to configure an IPv6 address for a group of interfaces that could belong on
different routers. If a packet is sent to that address, it should be received by all routers in the
group.
A.
Unicast
B.
Multicast
C.
Anycast
D.
Broadcast
Answer: B
Explanation:
What is the function of the hop limit field in the IPv6 header?
B.
It sets the number of hops in the network to be equal to the MPLS header time-to-live (TTL)
C.
It replaces the time-to-live (TTL) field in IPv4
D.
It represents future extensibility to the protocol
Answer: C
Explanation:
You have been asked to define a default gateway for traffic leaving a router. This route should use
interface so-0/0/0 as its next-hop. Which type of route would be suited for this scenario?
A.
a static route
B.
a generated route
C.
a martian route
D.
an aggregate route
Answer: A
Explanation:
A.
0
B.
1
C.
2
D.
3
Answer: C
Explanation:
You are asked to design a Layer 2 switched topology that can automatically recover from link
failures.
A.
GSTP
B.
LLDP
C.
LFM
D.
MSTP
Answer: D
Explanation:
When the Junos configuration shown in the exhibit is applied to the router, which routes in the
forwarding table will begin load-balancing packet flows?
A.
all routes in the forwarding table
B.
all OSPF routes in the forwarding table
C.
all BGP routes in the forwarding table
D.
all RFC1918 routes in the forwarding table
"Pass Any Exam. Any Time." - www.actualtests.com 101
Juniper JN0-360 Exam
Answer: D
Explanation:
You have configured MPLS and RSVP in your network using all of the Junos defaults. You
established an LSP in your network which is reporting an up status but no traffic is using it.
Which two statements reflect potential causes for this issue? (Choose two)
A.
The LSP egress address is a physical interface address
B.
family MPLS was omitted from the router configurations
C.
No BGP routes are being advertised from the remote neighbor
D.
The LSP egress address does not match the BGP next-hop address
Answer: C,D
Explanation:
Using industry best practices, what is true regarding an external BGP session?
A.
BGP neighbors belong to the same AS
B.
BGP neighbors belong to a different AS
C.
BGP sessions rely on a static route for reach ability
D.
BGP sessions will be established between loopback interface addresses.
You own a home network connecting through an always-on connection and need to assign IPv6
addresses to your routers because you want to follow the guidelines spelled out in RFC 3177. You
want to design your network with the correct prefixes.
A.
47-bit prefix
B.
48-bit prefix
C.
64-bit prefix
D.
128-bit prefix
Answer: B
Explanation:
From RFC 3177: This document provides recommendations to the addressing registries (APNIC,
ARIN and RIPE-NCC) on policies for assigning IPv6 address blocks to end sites. In particular, it
recommends the assignment of /48 in the general case, /64 when it is known that one and only
one subnet is needed and /128 when it is absolutely known that one and only one device is
connecting.
Which two BGP attributes are modified by default when they are passed between external BGP
peers? (Choose two)
A.
MED
B.
"Pass Any Exam. Any Time." - www.actualtests.com 103
Juniper JN0-360 Exam
AS-Path
C.
Communities
D.
Next Hop
Answer: B,D
Explanation:
In an RSTP network, the root and designated ports have been elected as shown in the exhibit
B.
discarding port
C.
alternate port
D.
listening port
Answer: A
Explanation:
A.
BGP uses UDP port 500 for connectivity.
B.
BGP uses TCP port 179 for connectivity.
C.
External peering sessions require an underlying IGP.
D.
Internal peering sessions require an underlying IGP.
Answer: B,D
Explanation:
Which two elements contribute to the bridge ID when configuring RSTP? (Choose 2)
A.
designated MAC address
C.
extended system ID
D.
root ID
E.
bridge address
Answer: A,B
Explanation:
The bridge ID consists of a configurable bridge priority and the MAC address of the bridge.
Reference:
http://www.juniper.net/techpubs/software/junos/junos95/swconfig-layer-2/conf-stp.html#conf-
bridge-priority
Using industry best practices, which two BGP attributes would you modify to accomplish this goal?
(Choose two)
A.
AS Path
B.
Local Preference
C.
Next Hop
D.
MED
Answer: A,D
Explanation:
You have recently installed a second Routing Engine (RE) in your router
Which two statements correctly describe the expected behavior if the primary RE fails?
(Choose two.)
A.
The backup RE will assume the master role once the packet forwarding engine restarts
B.
The backup RE will immediately assume the master role
C.
The new master RE restarts the routing protocol process (rpd) and establishes any required
adjacencies based on the configuration.
D.
The new master RE maintains the existing protocol adjacencies initially established by the
previous master RE
Answer: A,C
Explanation:
Which command would you use to verify the presence of VPN routes on a PE device?
A.
show route table bgp.l3vpn.0
B.
show route protocol bgp terse | count
C.
show route table inet.0
D.
show route route-type vpn
Answer: A
"Pass Any Exam. Any Time." - www.actualtests.com 107
Juniper JN0-360 Exam
Explanation:
A.
Layer 2 circuits use BGP for signaling
B.
Layer 2 circuits use OSPF for signaling
C.
Layer 2 circuits use LDP for signaling
D.
Layer 2 circuits rely on RSVP for signaling
Answer: C
Explanation:
A.
Interface loO must be configured in the IS-IS hierarchy
B.
Each network interface needs a unique family ISO address
"Pass Any Exam. Any Time." - www.actualtests.com 109
Juniper JN0-360 Exam
C.
The IS-IS level for an each interface must be specified
D.
The ISO address for interface loO is not in hex format
Answer: A
Explanation:
What are three circumstances under which a router sends link-state PDUs (LSPs)?
(Choose three)
A.
LSPs are sent periodically every 9 seconds
B.
LSPs are sent when there is a network change
C.
LSPs are sent during adjacency formation
D.
LSPs are sent in response to CSNP messages
E.
LSPs are sent in response to PSNP messages
Answer: B,C,E
Explanation:
In an RSTP network, which combination of port types can exist on the root bridge?
A.
There can be some combination of designated ports and backup ports
B.
C.
All ports will be designated ports
D.
All ports will be root ports
Answer: C
Explanation:
Your company has purchased two new Juniper Networks MX480 routers. Your manager has
asked you to add these two devices to the existing ISIS network.
Which two rules about ISIS adjacencies must you consider when carrying out the configuration?
(Choose two)
A.
For Level 1 adjacencies, area IDs must be the same
B.
For Level 2 adjacencies area IDs must be the same
C.
The IS-IS levels configured on the interfaces must be the same
D.
The IS-IS levels on the interfaces can be different
Answer: A,C
Explanation:
In the evaluation of an RSTP configuration BPDU, which two values are contained in the Bridge ID
value? (Choose two)
A.
B.
priority
C.
originating bridge address
D.
port number
Answer: B,C
Explanation:
A.
[edit routing-options family inet]
B.
[edit forwarding-options family inet]
C.
[edit routing-options forwarding-table]
D.
[edit forwarding-options forwarding-table]
Answer: C
Explanation:
Which two configuration elements are defined under an MSTP instance? (Choose two)
A.
revision-level
B.
C.
mstp-level
D.
vlan
Answer: B,D
Explanation:
The correct answer is B, D because revision-level is common for the all MSTI instances and it is
configured one level up from MSTI instance section.
Reference:
http://www.juniper.net/techpubs/en_US/junos10.0/information-products/topic-collections/config-
guide-mx-series-layer2/mstp-edit-protocols.html
Given the network topology shown in the exhibit, you are configuring a GRE tunnel from Router A
to Router C
Which interface configuration on Router A will successfully allow the tunnel to pass IPv4 traffic to
Router C?
A.
Option A
B.
Option B
D.
Option D
Answer: B
Explanation:
A.
IEEE 802.3 active monitoring
B.
IEEE 802.5 active monitoring
C.
carrier-sense multiple access with collision avoidance
D.
carrier-sense multiple access with collision detection
Answer: D
Explanation:
You have been asked to provision a service provider's network to accommodate Layer 3 VPNs as
defined in RPC 4364.
Which three tasks must be performed before the provider core is ready to carry VPN traffic?
(Choose three.)
A.
All P routers and PE routers must be configured to support MPLS administrative-groups (colors)
B.
C.
All P routers and PE routers must have a signaling protocol such as RSVP or LDP enabled
D.
All P routers and PE routers must have a discovery protocol such as LLDP or CDP enabled
E.
All P routers and PE routers must have MPLS reach ability to PE routers
Answer: B,C,E
Explanation:
You would like two LDP routers on opposite sides of your network to become neighbors. Which
LDP message is used to form this relationship?
A.
basic discovery
B.
extended discovery
C.
peer discovery
D.
remote discovery
Answer: B
Explanation:
A.
an enterprise environment with a single upstream connection
C.
a service provider environment
D.
a home office environment
Answer: B,C
Explanation:
A.
Import policy-a and policy-d. export policy-b and policy-c
B.
Import policy-d, export policy-b and policy-c
C.
Import policy-d. export policy-c.
D.
Import policy-d only
"Pass Any Exam. Any Time." - www.actualtests.com 117
Juniper JN0-360 Exam
Answer: C
Explanation:
In the exhibit Router A and Router B are operating on the LAN with Router B acting as the
designated intermediate system (DIS).
When Router C and Router D are added to the LAN. Which statement is true?
A.
Router C becomes the new DIS with no backup DIS.
B.
Router D becomes the new DIS with no backup DIS.
C.
Router C becomes the new DIS with Router B as the backup DIS.
D.
Router D becomes the new DIS with Router A as the backup DIS.
Answer: A
Explanation:
A.
cluster length
B.
router ID (RID)
C.
peer ID
D.
IGP cost
Answer: D
Explanation:
How many equal-cost paths can be assigned to a single route in the Junos OS?
A.
4
B.
16
C.
32
D.
64
Answer: B
Explanation:
http://www.juniper.net/techpubs/software/junos/junos70/swconfig70-policy/html/policy-actions-
config11.html
You want to configure support for an IPv6 environment In which hierarchy would you configure an
OSPF area?
A.
[edit protocols ospf-v6]
B.
[edit protocols ipv6-ospf
C.
[edit protocols ipv6J
D.
[edit protocols ospf3]
Answer: D
Explanation:
Which action does the local router take after sending a Notification message to a remote peer?
A.
It begins to send route update information
B.
It tears down the TCP session and attempts to re-establish it
C.
It waits for the remote router to acknowledge that it is ready to receive routes
D.
It changes its local state to Established
Answer: B
Explanation:
You have been asked to configure and assign addresses for your IPv6 routers in your network
using dynamic assignment of DNS servers. You do not want the MAC address included as part of
the IPv6 address.
A.
DHCP
B.
stateless auto configuration
C.
DHCPv6
D.
stateful auto configuration
Answer: C
Explanation:
Which two topologies shown in the exhibit would require the use of a spanning-tree protocol?
(Choose two)
A.
ring
B.
tree
C.
star
D.
mesh
Answer: A,D
Explanation:
Which three functions are performed by an OSPF area border router (ABR)? (Choose three)
A.
flooding Summary LSAs to connected areas
B.
"Pass Any Exam. Any Time." - www.actualtests.com 122
Juniper JN0-360 Exam
flooding ASBR Summary LSAs to connected areas
C.
generating all Router LSAs for connected neighbors
D.
performing summarization on routes headed to Area 0
E.
flooding NSSA External LSAs to Area 0
Answer: A,B,D
Explanation:
Which configuration will allow for the switch to potentially look at the IP header of incoming frames
tagged with a VLAN ID of 222?
A.
Option A
B.
Option B
C.
Option C
D.
Option D
Answer: D
Explanation:
Your area border router (ABR) receives type 1.2 and 5 link-state advertisements (LSAs) from a
non-backbone area.
What would the ABR do with the information learned from the non-backbone area?
A.
The ABR will generate type 2 and 3 LSAs and flood type 5 LSAs to the backbone area
B.
The ABR will generate only type 3 LSAs and flood only type 5 LSAs to the backbone area
C.
The ABR will generate type 3 and 4 LSAs. And flood type 5 LSAs to the backbone area
D.
The ABR will generate only type 4 LSAs and flood only type 5 LSAs to the backbone area
Answer: C
Explanation:
A.
Pop
B.
Push
C.
Replace
D.
Swap
Answer: B
Explanation:
An RSVP LSP in your network is operational but you are receiving complaints about network
throughput across the LSP. You suspect that the RSVP bandwidth was omitted from the router
configuration.
Which operational mode command will help you verify your suspicions?
A.
show interfaces terse
B.
show mpls lsp extensive
C.
show rsvp neighbor detail
D.
show rsvp bandwidth
Answer: B
Explanation:
After configuring OSPF between two routers you check for an adjacency. You see that the
adjacencies are not coming up on an Ethernet segment.
What are two reasons that would cause this situation? (Choose two)
A.
You have a mismatched IP subnet/mask
B.
Your hello timer intervals are mismatched
C.
You are not using the same Junos version on each side
D.
You priority values are mismatched
Answer: A,B
A.
all of the headers of the LSPs in a router's link-state database
B.
all of the IP routes in a router's link-state database
C.
all of the IP routes in a router's routing table
D.
all of the LSPs in a router's link-state database
Answer: A
Explanation:
You want to ensure that your RSVP LSPs are following a particular path across the network.
A.
explicit route object
B.
record route object
C.
session object
D.
traffic specification object
Answer: A
A.
Layer 2 VPNs require that CE devices use the same Layer 2 encapsulation
B.
Layer 2 VPNs do not permit CE devices to operate a Layer 3 protocol with each other
C.
Service provider routers must evaluate the IP header of packets as they traverse their network
D.
Layer 2 VPNs allow CEs to use different encapsulations on either side of the VPN
Answer: D
Explanation:
A.
PE-B would flood the packet to all attached PEs
B.
PE-B would forward the packet to the root PE device
C.
PE-B would forward the packet to all attached CE devices
D.
PE-B would discard the packet
Answer: C
Explanation:
Based on the configuration shown in the exhibit, which command would you use to display real-
"Pass Any Exam. Any Time." - www.actualtests.com 129
Juniper JN0-360 Exam
time hellos and errors for IS-IS?
A.
monitor file isis-log
B.
monitor start isis-log
C.
monitor log isis-log
D.
monitor syslog isis-log
Answer: B
Explanation:
An Ethernet bridge is configured such that all interfaces are in a single broadcast domain By
default.
Which two tasks does the bridge perform in response to receiving a multicast frame?
(Choose two)
A.
It learns the source MAC address
B.
It drops the frame
C.
It floods the frame out of all interfaces except the one on which it was received
D.
It floods the frame out of particular interfaces based on its multicast MAC table
Answer: A,C
Explanation:
What must also be configured for this interface to participate in VLAN 100 and 200?
A.
broadcast domains
B.
VLANs
C.
bridge domains
D.
encapsulation type
Answer: C
Explanation:
You are logged into a PE router participating in a Layer 3 VPN as defined in RFC 4364. You would
like to ping the remotely connected CE router's loopback address. The address of the loopback is
122.161.2.1, the VPN routing-instance is called VPN-C. Which command will accomplish this
goal?
A.
ping instance VPN-C 122.161.2.1
C.
ping VPN-C 122.161.2.1
D.
ping vpn-instance VPN-C 122.161.2.1
Answer: B
Explanation:
Which configuration can be applied to ensure that no more than 600 MAC addresses are learned
by a virtual switch?
A.
Option A
B.
Option B
C.
Option C
D.
Option D
Answer: C
Explanation:
You have two routers connected over a Gigabit Ethernet link as shown in the exhibit It is required
that an IS-IS adjacency be established without the need for a designated intermediate system
(DIS)
Which configuration statement entered on both routers will achieve this goal?
A.
set interface ge-0/0/2 unit 0 family iso no-dis
B.
set interface ge-0/0/2 unit 0 family iso point-to-point
C.
set protocols isis interface ge-0/0/2.0 no-dis
D.
set protocols isis interface ge-0/0/2.0 point-to-point
Answer: D
Explanation:
A.
BGP routes learned from Router A only
B.
BGP routes learned from Router E only
C.
BGP routes learned from Routers A and C only
D.
BGP routes learned from Routers A, C and E only
Answer: D
Explanation:
Which two problems occur when increasing numbers of users are added to an Ethernet LAN with
no switches present? (Choose two.)
"Pass Any Exam. Any Time." - www.actualtests.com 135
Juniper JN0-360 Exam
A.
There is a greater chance for collisions to occur
B.
The MAC table sizes increase
C.
Some devices will not see certain traffic
D.
There is unnecessary consumption of network bandwidth
Answer: A,D
Explanation:
Given the OSPF network topology shown in the exhibit, you would like to inject external (non-
OSPF) routes into the network on Router D
Which two OSPF area types will support this configuration? (Choose two)
B.
totally stubby area
C.
not-so-stubby area
D.
non-backbone area
Answer: C,D
Explanation:
In your network, you have two LDP routers connected across four physical interfaces. You have
also enabled LDP to operate on all four of those interfaces.
What is the resulting outcome of your configuration between those two routers?
A.
One session is built across one neighbor relationship
B.
One session is built across four neighbor relationships
C.
Four sessions are built across one neighbor relationship
D.
Four sessions are built across four neighbor relationships
Answer: B
Explanation:
B.
fixed filter
C.
shared explicit
D.
wildcard filter
Answer: B
Explanation:
A.
iBGP peering adds value in small networks with a single upstream connection
B.
iBGP peering adds value in small networks with multiple upstream connections
C.
eBGP peering adds value in small networks with multiple upstream connections
D.
iBGP peering adds value in large enterprise environments with multiple upstream connections
E.
eBGP peering adds value in large enterprise environments with multiple upstream connections
Answer: C,D,E
Explanation:
You observe that VPN routes are hidden on your PE router Which situation accounts for these
hidden routes?
B.
The protocol next-hop is not found in mpls 0
C.
The protocol next-hop is not found in bgp I3vpn 0
D.
The protocol next-hop is not found in inet 2
Answer: A
Explanation:
To prevent fragmentation issues across a GRE tunnel, which MTU value is recommended for the
tunnel to accommodate most IP packets?
A.
1476
B.
1492
C.
1500
D.
1524
Answer: D
Explanation:
By default, which three criteria are used by the Junos load-balancing algorithm to determine a
traffic flow? (Choose three.)
A.
B.
source port
C.
destination port
D.
source address
E.
destination address
Answer: A,D,E
Explanation:
Based on the configuration shown in the exhibit, what will be the state of the IS-IS levels on
interface ge-0/0/0.100?
A.
Level 1 is enabled and Level 2 is disabled.
B.
Level 1 is disabled and Level 2 is enabled.
D.
Level 1 is disabled and Level 2 is disabled.
Answer: D
Explanation:
A.
Frames will be counted initially by filterB and then counted by filterA.
"Pass Any Exam. Any Time." - www.actualtests.com 142
Juniper JN0-360 Exam
B.
Frames will be counted initially by filterA and then counted by filterB.
C.
Frames will be counted by filterA only.
D.
Frames will be counted by filterB only.
Answer: B
Explanation:
Given the OSPF topology shown in the exhibit, how many unique link-state databases are present
in the network?
A.
1
B.
2
C.
"Pass Any Exam. Any Time." - www.actualtests.com 143
Juniper JN0-360 Exam
3
D.
6
Answer: C
Explanation:
In the exhibit, three IPv6 addresses are listed. Which two statements are true? (Choose two.)
A.
The first address is complete and correct.
B.
The third address is not formatted correctly.
C.
All three addresses are the same.
D.
The second address is incomplete and not correct.
Answer: A,C
Explanation:
You have just configured IPv6 in your network. A packet arrives on your router that exceeds the
MTU size. How will an IPv6 router respond?
A.
"Pass Any Exam. Any Time." - www.actualtests.com 144
Juniper JN0-360 Exam
The fragment offset is referenced and the packet is fragmented.
B.
The packet is kept intact and not fragmented.
C.
The packet is dropped.
D.
The packet is fragmented based on extension headers.
Answer: C
Explanation:
Which two statements reflect benefits of performing per-flow load balancing over per-packet load
balancing? (Choose two.)
A.
All physical links in the network are used equally.
B.
Packets arrive at the destination in the order they were sent.
C.
Provides easier implementation of class of service policies.
D.
Allows the destination host to re-order packets and increase performance.
Answer: B,C
Explanation:
By default, the Junos OS advertises which address(es) in LDP forwarding equivalency class (FEC)
messages?
A.
all router addresses
C.
loopback address
D.
primary transit interface address
Answer: C
Explanation:
What must be configured as part of the ge-1/0/3 interface configuration to accept tagged frames of
VLANs 100 and 200?
A.
encapsulation vlan-bridge
B.
encapsulation ethernet-bridge
C.
interface-mode trunk
D.
"Pass Any Exam. Any Time." - www.actualtests.com 146
Juniper JN0-360 Exam
vlan-id-range [100 200]
Answer: C
Explanation:
A.
Refresh
B.
Hello
C.
Route
D.
Keepalive
E.
Open
Answer: A,D,E
Explanation:
What are two benefits of using an OSPF designated router (DR)? (Choose two.)
A.
Reduces the size of the link-state database.
B.
Reduces LSA flooding on a broadcast segment.
C.
Reduces LSA flooding throughout an OSPF area.
D.
Answer: B,D
Explanation:
Which three statements are true regarding the show system switchover operational mode
command? (Choose three.)
A.
This command can only be issued on the master Routing Engine.
B.
This command displays the status of graceful switchover.
C.
This command can only be issued on the backup Routing Engine.
D.
This command displays the status of the interface and process databases.
E.
This command displays the status of the kernel database.
Answer: B,C,E
Explanation:
You have been asked to use a convention that allows for auto configuration of interface
addresses. You are not allowed to use DHCPv6. What do you do?
A.
Use IPv4 with the autoconfig option under family inet.
B.
Use IPv6 in the network to configure hosts.
C.
Use a program (e.g. Vector-Wiz) to auto configure IP addresses.
Answer: B
Explanation:
You notice that the RID of your router is being taken from the address of your management
interface.
A.
The loopback address was configured with a /32 address.
B.
The loopback address was not configured under [edit protocols ospf].
C.
A suitable loopback address was not configured on the router.
D.
The loopback address was configured under [edit routing-options].
Answer: C
Explanation:
You have been asked to identify what the contributing routes are for route 204.7.15/21. Which
command will show this information?
A.
show route 204.7.15/21
B.
show route 204.7.15/21 extended
C.
D.
show route 204.7.15/21 detail
Answer: D
Explanation:
Which packet type does the router use to request up-to-date link-state information?
A.
IIH
B.
LSP
C.
PSNP
D.
CSNP
Answer: C
Explanation:
Which forwarding table designation is used to indicate that load balancing is working correctly?
A.
ucst
B.
msct
C.
ulst
D.
Answer: C
Explanation:
Which two statements are correct regarding VPLS mesh groups? (Choose two.)
A.
Unicast packets destined to another PE router within the same mesh group are dropped by the
local PE router.
B.
Unicast packets destined to another PE router in a different mesh group are dropped by the local
PE router.
C.
Broadcast, multicast, and unicast packets of unknown origin received from a PE router are flooded
to all local CE routers.
D.
Broadcast, multicast, and unicast packets of unknown origin received from a PE router are flooded
to all remote PE routers.
Answer: A,C
Explanation:
Router A receives two similar route advertisements from different BGP peers. What would cause a
route to be selected in this scenario?
A.
having a lower MED value
B.
having a lower local preference
C.
learning a route from a peer with a higher peer ID
"Pass Any Exam. Any Time." - www.actualtests.com 151
Juniper JN0-360 Exam
D.
learning a route from a peer with a higher IGP metric
Answer: A
Explanation:
Which two configuration elements must match on all switches participating in the same MSTP
region? (Choose two.)
A.
mstp-version
B.
configuration-name
C.
msti-revision
D.
revision-level
Answer: B,D
Explanation:
B.
These routes are internal Level 2 routes.
C.
These routes are external Level 1 routes.
D.
These routes are external Level 2 routes.
Answer: B
Explanation:
A.
Nodes share a physical medium.
B.
Nodes can successfully transmit simultaneously.
C.
It consists of a single broadcast domain.
D.
Nodes use a step-up algorithm when collisions are detected.
Answer: A,C
Explanation:
You are logged into a PE router participating in a Layer 3 VPN as defined in RFC 4364. You would
like to ping the locally connected CE router's interface. The address of the interface is
192.168.1.1; the VPN routing-instance is named VPN-A. Which command will accomplish this
task?
B.
ping instance VPN-A 192.168.1.1
C.
ping vpn-instance VPN-A 192.168.1.1
D.
ping VPN-A 192.168.1.1
E.
ping mpls l3vpn VPN-A 192.168.1.1
Answer: E
Explanation:
Before configuring an RSVP LSP in your network, you first apply a baseline configuration to all of
the routers. Which three configuration elements are minimally required in the baseline? (Choose
three.)
A.
family mpls on the loopback interface
B.
family mpls on the transit interfaces
C.
protocols ldp for the appropriate interfaces
D.
protocols mpls for the appropriate interfaces
E.
protocols rsvp for the appropriate interfaces
Answer: B,D,E
Explanation:
From the output shown in the exhibit, what would happen to a packet destined for address
172.29.3.5?
A.
The address is not in the aggregate range; the packet is sent to the Routing Engine.
B.
The address is in the aggregate range; the packet will be silently dropped.
C.
The address is not in the aggregate range; the packet will be forwarded.
D.
The address is in the aggregate range; the packet will be dropped.
Answer: A
Explanation:
Your customer complains that their Layer 3 VPN is not passing traffic from one site to another.
You assigned that customer to VPN-A. Which command on the PE router will confirm the
presence of customer routes?
B.
show route VPN-A table bgp.l2vpn.0
C.
show route table inet.3 VPN-A
D.
show route table VPN-A.inet.0
Answer: D
Explanation:
A.
a designated intermediate system
B.
an area border router
C.
a router with an IS-IS export policy
D.
a router connected to the backbone
Answer: A
Explanation:
Router B is an OSPF router connected to both Area 0 and Area 2. Area 2 has been configured as
a totally stubby area. Which three LSA types does Router B suppress from Area 2? (Choose four.)
A.
Router LSA
C.
External LSA
D.
Summary LSA
E.
ASBR Summary LSA
Answer: A,B,C,E
Explanation:
What is the size of the unique address used to identify each node on an Ethernet LAN?
A.
3 bytes
B.
6 bytes
C.
9 bytes
D.
12 bytes
Answer: B
Explanation:
Which two IS-IS packet types are used to maintain IS-IS database synchronization? (Choose two.)
A.
IIH
C.
PSNP
D.
CSNP
Answer: C,D
Explanation:
You notice that a route from internal BGP peer 192.168.1.1 is missing from the local route table.
Which two commands would be used to help identify the source of the problem? (Choose two.)
A.
show route bgp
B.
show route protocol bgp hidden
C.
show route receive-protocol bgp 192.168.1.1
D.
show route advertising-protocol bgp 192.168.1.1
Answer: B,C
Explanation:
What are three ways to configure IPv6 addresses in your network? (Choose three.)
A.
Statically configure your IPv6 addresses.
B.
Configure your IPv6 addresses using stateless auto configuration.
D.
Configure your IPv6 addresses by assigning your router a prefix list.
E.
Configure your IPv6 addresses by configuring support for unicast-arp-negotiation.
Answer: A,B,C
Explanation:
Which two topologies shown in the exhibit could be implemented without a spanning-tree
protocol? (Choose two.)
A.
ring
B.
tree
C.
star
Answer: B,C
Explanation:
In the exhibit, all routers are sending routes to Router B. Which routes will be advertised from
Router B to Router E?
A.
BGP routes learned from Router A only
B.
BGP routes learned from Router D only
C.
BGP routes learned from Routers A and C only
D.
BGP routes learned from Routers A, C, and D only
In your RSVP network you have configured three separate LSPs to the same egress address. You
have made no other configuration changes to the forwarding decisions made by the router. Which
commands can you use to determine which LSP is being used to forward packets?
A.
show route table inet.3
B.
show route table inet.4
C.
show rsvp neighbor
D.
show rsvp session
Answer: A
Explanation:
Which two values are used by an RSTP bridge to remove stale BPDU information? (Choose two.)
A.
Message Age
B.
Forwarding Delay
C.
Hello Time
D.
Max Age
Answer: A,D
"Pass Any Exam. Any Time." - www.actualtests.com 161
Juniper JN0-360 Exam
Explanation:
After the MAC learning limit of 3000 is reached for the bd bridge domain as shown in the exhibit,
what happens to frames that arrive that contain unknown unicast destination addresses?
A.
They are flooded.
B.
The are forwarded to the default gateway.
C.
They are dropped.
D.
They are forwarded to the IRB interface.
Answer: A
Explanation:
You have recently configured MSTP on two switches in your network to participate in the same
MSTP region. You issue the show spanning-tree mstp configuration command on both switches
A.
Everything is functioning as expected because the configuration digests should not match.
B.
You should ensure that the max-age and hello timers are equal on both switches.
C.
You should ensure that the bridge IDs and priority values are unique on both switches.
D.
You should ensure that the MSTIs and their VLAN IDs are equal on both switches.
Answer: D
Explanation:
You have a stub OSPF area running in your network. Your supervisor has asked you to build a
virtual link across this area to connect new equipment acquired in a recent ISP acquisition. Which
statement is correct about this scenario?
A.
Type 5 LSAs would be blocked in a stub area.
B.
Type 5 LSAs would carry external information across your transit area to the backbone.
C.
Type 5 LSAs would be seen only in the newly attached area.
D.
Type 5 LSAs would be converted to type 7 LSAs.
Answer: A
Explanation:
You own a small company and need to assign IPv6 addresses to your routers. Because you want
A.
47-bit prefix
B.
48-bit prefix
C.
64-bit prefix
D.
128-bit prefix
Answer: B
Explanation:
Your customer would like to forward traffic using DLCI 600 and maintain Layer 2 information
across a VPN. Which solution will meet these requirements?
A.
a Layer 3 VPN
B.
a Layer 2 VPN
C.
Virtual Private LAN Service (VPLS)
D.
an IPsec VPN
Answer: B
Explanation:
You have two OSPF routers that are trying to form an adjacency. When you issue the command
A.
The router does not know about the received LSA header and has transmitted a link-state request.
B.
The router has finished transmitting, but is still receiving database information.
C.
The router is waiting for a start event.
D.
The router has established bidirectional communication with its peer.
Answer: B
Explanation:
Which two events could cause the BGP Active state to appear? (Choose two.)
A.
The local router does not have a route to the peer device.
B.
The local router failed to establish a TCP connection with the peer device.
C.
A firewall is stopping all UDP packets.
D.
The BGP configuration is incomplete.
Answer: B,D
Explanation:
The policy shown in the exhibit has been configured and installed on your router.
A.
The 172.18.1.0/24 network will be redistributed into OSPF as an external route.
B.
The 172.18.1.0/24 network will be redistributed into OSPF as an internal route.
C.
The 172.18.1.0/32 network will be redistributed into OSPF as an external route.
D.
The 172.18.1.0/32 network will be redistributed into OSPF as an internal route.
Answer: A
Explanation:
Which type of router can provide connectivity between areas in an IS-IS domain?
B.
a Level 2 router with adjacencies in more than one area
C.
an area border router with adjacencies in more than one area
D.
a Level 2 router with adjacencies in a single area
Answer: B
Explanation:
You have been asked to provision a service provider's network to accommodate Layer 3 VPNs as
defined in RFC 4364. Which three tasks must be performed before the provider network is ready
to carry VPN traffic? (Choose three.)
A.
All Juniper Networks PE routers must be configured with an appropriate router-ID unique to the
VPN.
B.
All Juniper Networks PE routers must be configured with an appropriate route-target unique to the
VPN.
C.
All Juniper Networks PE routers must be configured with a routing-instance of type forwarding.
D.
All Juniper Networks PE routers must be configured with a routing-instance of type vrf.
E.
All Juniper Networks PE routers must be configured with a routing-instance containing the CE-
facing interface.
Answer: B,D,E
Explanation:
By default, which BGP attribute is only compared when two route advertisements are received
from the same neighboring AS?
A.
MED
B.
AS-Path
C.
Communities
D.
Next Hop
Answer: A
Explanation:
Referring to the exhibit, what must be true of the vlan_100 bridge domain?
A.
vlan_100 has at least one Ethernet interface assigned to it.
B.
vlan_100 does not have an Ethernet interface assigned to it.
C.
vlan_100 might have an active Ethernet interface assigned to it.
D.
"Pass Any Exam. Any Time." - www.actualtests.com 168
Juniper JN0-360 Exam
vlan_100 does not have an active Ethernet interface assigned to it.
Answer: D
Explanation:
An Ethernet bridge is configured such that all interfaces are in a single broadcast domain. Which
two tasks does the bridge perform in response to receiving a frame with an unknown unicast
destination MAC address? (Choose two.)
A.
It drops the frame.
B.
It floods the frame out of all interfaces except the one on which is was received.
C.
It learns the destination MAC address.
D.
It learns the source MAC address.
Answer: B,D
Explanation:
You have configured multiple IP-IP tunnels across your network to provide connectivity to remote
sites. Which technique is used to help the IP endpoints in your network determine the optimal
packet size to send across your tunnels?
A.
path MTU discovery
B.
fragmentation discovery
C.
end-to-end MTU discovery
Answer: A
Explanation:
You have configured an RSVP LSP in your network and have assigned it one primary and two
secondary paths.
Which command is used to validate that the LSP is using the primary path?
A.
show rsvp interface
B.
show rsvp version
C.
show rsvp neighbor detail
D.
show rsvp session detail
Answer: D
Explanation:
A.
It is used in BGP route selection.
B.
It is used to ensure that a packet traverses the least number of routers.
C.
It is used by IGPs to avoid loops within an autonomous system.
"Pass Any Exam. Any Time." - www.actualtests.com 170
Juniper JN0-360 Exam
D.
It is used to avoid routing loops between autonomous systems.
Answer: A,D
Explanation:
A.
IIH
B.
LSP
C.
PSNP
D.
CSNP
Answer: B
Explanation:
Which three statements are true regarding the show system switchover operational mode
command? (Choose three.)
A.
This command can only be issued on the master Routing Engine.
B.
This command displays the status of graceful switchover.
C.
This command can only be issued on the backup Routing Engine.
D.
This command displays the status of the interface and process databases.
Answer: B,C,E
Explanation:
Which three elements contribute to the bridge ID when configuring RSTP? (Choose three.)
A.
designated MAC address
B.
priority
C.
extended system ID
D.
root ID
E.
bridge address
Answer: B,C,E
Explanation:
Which LDP message is used to transmit labels and forwarding equivalency class (FEC)
information?
A.
advertisement
B.
discovery
C.
notification
Answer: A
Explanation:
You are logged into a router and have navigated to the [edit routing-options] level of the hierarchy.
You have been asked to create a static route that will use 43.18.7.1 as its primary next-hop and
76.13.10.2 as its secondary next-hop.
A.
set static route 0/0 76.13.10.2 qualified-next-hop 43.18.7.1 pref 10
B.
set static route 0/0 next-hop 43.18.7.1 secondary-next-hop 76.13.10.2 preference 10
C.
set static route 0/0 next-hop [76.13.10.2 10.10.10.5] pref 10
D.
set static route 0/0 next-hop 43.18.7.1 qualified-next-hop 76.13.10.2 preference 10
Answer: D
Explanation:
By default, which Junos routing table stores RSVP egress router information?
A.
inet.1
B.
inet.2
C.
D.
inet.4
Answer: C
Explanation:
You are logged into a router and have navigated to the [edit routing-options] level of the hierarchy.
You have been asked to define an aggregate route for 172.30/16.
A.
set summary route 172.30/16
B.
set aggregate route 172.30/16
C.
set route aggregate 172.30/16
D.
set route summary 172.30/16
Answer: B
Explanation:
When sending BGP routes in an Update message, how are they grouped?
A.
by grouping aggregated address ranges together
B.
by using a complete set of matching attributes
"Pass Any Exam. Any Time." - www.actualtests.com 174
Juniper JN0-360 Exam
C.
by the originating autonomous system
D.
by the originating router
Answer: B
Explanation:
You work for the regional Internet service provider shown in the exhibit. You have a partial BGP
table and are receiving a 10.100/16 route from your upstream ISP. You have been asked to
configure a default route that can be sent to your downstream customer. This route should forward
customer traffic toward your upstream Tier 1 ISP as long as the 10.100/16 route is present.
A.
Create and announce an aggregate default route.
B.
Create and announce a static default route with a next-hop of discard.
C.
Create and announce a static default route with a next-hop of reject.
D.
Create and announce a generated default route.
Answer: D
"Pass Any Exam. Any Time." - www.actualtests.com 175
Juniper JN0-360 Exam
Explanation:
-- Exhibit --
interfaces {
ge-0/0/0 {
vlan-tagging;
unit 100 {
vlan-id 100;
family inet {
address 192.168.100.97/30;
family iso;
unit 200 {
vlan-id 200;
family inet {
address 192.168.100.94/30;
family iso;
fxp0 {
unit 0 {
family inet {
"Pass Any Exam. Any Time." - www.actualtests.com 176
Juniper JN0-360 Exam
address 10.210.10.11/27;
lo0 {
unit 0 {
family inet {
address 192.168.100.1/32;
family iso {
address 49.1111.1921.6801.0001.00;
protocols {
isis {
interface ge-0/0/0.100;
interface ge-0/0/0.200;
-- Exhibit --
B.
Each network interface needs a unique family ISO address.
C.
The IS-IS level for an each interface must be specified.
D.
The ISO address for interface lo0 is not in hex format.
Answer: A
Explanation:
-- Exhibit --
ge-1/0/0 up up
fec0:0:0:2003::1/64
-- Exhibit --
You run the command show interfaces terse ge-1/0/0 and see the output shown in the exhibit.
A.
Two addresses are assigned in IPv6, one for the physical and one for the logical interface.
B.
Two addresses are seen because the loopback address of the router is associated with the
C.
The two addresses being seen are the link-local and site-local.
D.
An IPv6 address conflict is being seen; verify your interface configuration for problems.
Answer: C
Explanation:
-- Exhibit --
[edit]
term 1 {
from {
protocol bgp;
neighbor 10.0.21.2;
-- Exhibit --
Router-X has an external peering session to 10.0.21.2 and several internal peers.
How can the policy referenced in the exhibit be used to make sure routes are usable?
A.
Apply nhs as an import policy to internal BGP peers.
C.
Apply nhs as an import policy to external BGP peers.
D.
Apply nhs as an export policy to external BGP peers.
Answer: B
Explanation:
-- Exhibit --
protocols {
isis {
interface lo0.0;
interface ge-0/0/0.100;
-- Exhibit --
Referring to the exhibit, what will be the IS-IS levels enabled on the interface ge-0/0/0.100?
A.
Level 1 only
B.
Level 2 only
C.
Level 1 and Level 2
D.
Answer: C
Explanation:
Topic 3, Volume C
You have three aggregate routes all with the same route preference.
A.
lowest metric value
B.
secondary route preference
C.
highest metric value
D.
lowest community value
Answer: B
Explanation:
You are configuring a trunk interface on an MX Series device and want to ensure that any
outgoing frames associated with VLAN 100 are transmitted as untagged frames.
A.
routing-interface irb.0
B.
"Pass Any Exam. Any Time." - www.actualtests.com 181
Juniper JN0-360 Exam
vlan-id-list [100]
C.
native-vlan-id 100
D.
vlan-id 100
Answer: A
Explanation:
An RSVP enabled router receives an RSVP reservation message for a new RSVP path. The
router is unable to accommodate the reservation request.
A.
The router sends a ResvErr message to the upstream router.
B.
The router sends a ResvErr message to the downstream router.
C.
The router sends a ResvTear message to the upstream router.
D.
The router sends a ResvTear message to the downstream router.
Answer: D
Explanation:
What are two valid protocols used to signal VPLS in a network? (Choose two.)
A.
RSVP
B.
"Pass Any Exam. Any Time." - www.actualtests.com 182
Juniper JN0-360 Exam
CCC
C.
BGP
D.
LDP
Answer: C,D
Explanation:
A.
penultimate router
B.
egress router
C.
ingress router
D.
ultimate router
Answer: A
Explanation:
You are asked to deploy OSPF between two routers over a broadcast medium.
Which three fields in the OSPF hello packet must match? (Choose three.)
A.
hello interval
B.
options
"Pass Any Exam. Any Time." - www.actualtests.com 183
Juniper JN0-360 Exam
C.
backup designated router
D.
network mask
E.
designated router
Answer: A,B,D
Explanation:
Which three STP protection mechanisms are supported on MX Series, EX Series, and QFX Series
devices? (Choose three.)
A.
trunk protection
B.
BPDU protection
C.
loop protection
D.
access protection
E.
root protection
Answer: B,C,E
Explanation:
A.
They are converted into Type 5 LSAs by the ASBR.
C.
They are converted into Type 3 LSAs by the ABR.
D.
They are converted into Type 4 LSAs by the ABR.
Answer: B
Explanation:
A.
BGP routes are created using policies associated with BGP peering sessions.
B.
BGP routes are created using IP subnet definitions at each defined BGP peer.
C.
BGP routes are created based on interface subnets used for peering sessions.
D.
BGP routes are created based on all interface subnets on all BGP routers.
Answer: A
Explanation:
What are two destination addresses used for OSPF link-state update packets? (Choose two.)
A.
224.0.0.1
B.
224.0.0.4
D.
224.0.0.5
Answer: C,D
Explanation:
Which three statements are true about BGP default operations? (Choose three.)
A.
IBGP peers advertise routes received from EBGP peers to other IBGP peers.
B.
IBGP peers do not advertise routes received from IBGP peers to other IBGP peers.
C.
IBGP peers do not advertise routes received from EBGP peers to other IBGP peers.
D.
IBGP peers change the next hop for routes received from EBGP peers.
E.
EBGP peers advertise routes learned from IBGP or EBGP peers to other EBGP peers.
Answer: A,B,E
Explanation:
R1 is an OSPF router with a priority of 100 and has been elected as the designated router (DR).
R2 is the backup designated router (BDR) with a priority of 50. A third router, R3, comes online
with a priority of 200.
A.
B.
R3 will be the DR and R1 will be the BDR.
C.
R2 will be the DR and R1 will be the BDR.
D.
R3 will be the DR and R2 will be the BDR.
Answer: A
Explanation:
Referring to the exhibit, which two statements are correct about R2? (Choose two.)
A.
If R2 remains in the ExStart state, then you should verify the MTU setting on R2 and R3.
B.
R2 LSDB is synchronized with R1.
C.
If R2 remains in the ExStart state, then you should verify Physical Layer and Data Link Layer
connectivity on R2 and R3.
D.
R2 LSDB is not synchronized with R1.
Answer: A,B
"Pass Any Exam. Any Time." - www.actualtests.com 187
Juniper JN0-360 Exam
Explanation:
Your network runs RSTP and includes a LAN segment shared by two MX Series devices. The two
MX Series devices sharing this LAN segment each have two connections on the shared segment.
A.
The port on the selected MX Series device with the lowest port ID is selected as the designated
port.
B.
The MX Series device with the highest-cost path to the root bridge is selected as a designated
bridge for the shared segment.
C.
The port on the selected MX Series device with the highest port ID is selected as the designated
port.
D.
The MX Series device with the least-cost path to the root bridge is selected as the designated
bridge for the shared segment.
Answer: A,D
Explanation:
Your network consists of multiple remote locations using both IPv4 and IPv6. You have an IPv4-
based Internet connection at each site provided by different, local service providers. You are
asked to ensure that the remote IPv6 networks are able to communicate.
A.
Create GRE tunnels between the remote locations to connect the IPv6 networks.
B.
C.
Create IP-IP tunnels between the remote locations to connect the IPv6 networks.
D.
Create MPLS tunnels between the remote locations to connect the IPv6 networks.
Answer: C
Explanation:
You are asked to deploy OSPF between two routers over a point-to point link.
Which three fields in the OSPF hello packet must match? (Choose three.)
A.
network mask
B.
hello interval
C.
options
D.
dead interval
E.
backup designated router
Answer: B,C,D
Explanation:
Which two Layer 2 protocols are supported on MX Series devices? (Choose two.)
A.
BGP
"Pass Any Exam. Any Time." - www.actualtests.com 189
Juniper JN0-360 Exam
B.
RIP
C.
RSTP
D.
MSTP
Answer: C,D
Explanation:
Which two statements are correct according to the output shown in the exhibit? (Choose two.)
A.
The peering session is enabled for graceful restart.
B.
The peering session uses the default route preference.
C.
The peering session is in a state in which routes can be exchanged.
D.
The peering session uses a 4-byte AS number.
Answer: B,C
Explanation:
On an Ethernet segment, OSPF DROther routers form which type of adjacency with each other?
A.
Full
B.
2Way
C.
ExStart
D.
Exchange
Answer: B
Explanation:
A.
Routing information cannot be shared between routing instances.
B.
Each routing protocol runs in a separate routing instance.
C.
Junos devices support only one routing instance.
D.
Each routing instance is a unique grouping of routing tables, interfaces, and routing protocol
parameters.
Answer: D
Explanation:
A.
2Way
B.
Full
C.
ExStart
D.
Exchange
Answer: A
Explanation:
Which two statements are correct according to the output shown in the exhibit? (Choose two.)
A.
The peering session can pass inet-vpn routes.
B.
The peering session uses an altered route preference.
C.
The peering session is enabled for multihop support.
D.
The peering session is enabled for multipath support.
Answer: A,B
Explanation:
Referring to the exhibit, which policy would be applied to the 75.217.12.10 neighbor?
A.
The my-statics policy would be applied.
B.
The my-aggregates policy would be applied.
C.
The my-specifics policy would be applied.
D.
The my-statics, my-aggregates, and my-specifics policies would be applied.
Answer: D
Explanation:
Referring to the exhibit, all interswitch links are configured as trunks supporting all VLANs. Host A
sends a frame with an unknown destination MAC address to S2.
A.
S1, S3 and S4
B.
S1 only
C.
S1 and S3 only
D.
S1 and S4 only
Answer: C
Explanation:
Which table will a Junos-based MPLS ingress router first consult to determine the next hop for
BGP routes reachable through an LSP?
A.
inet.1
B.
mpls.0
C.
inet.3
"Pass Any Exam. Any Time." - www.actualtests.com 196
Juniper JN0-360 Exam
D.
inet.0
Answer: D
Explanation:
Which Layer 2 mechanism logically groups network nodes into separate broadcast domains?
A.
IS-IS levels
B.
OSPF areas
C.
VLAN
D.
IP subnets
Answer: C
Explanation:
Switch 1 and Switch 2 are configured to run MSTP. However, MSTP is not working.
Referring to the exhibit, which two actions will correct the problem? (Choose two.)
A.
Configure interface ge-0/0/2 on Switch 2
"Pass Any Exam. Any Time." - www.actualtests.com 198
Juniper JN0-360 Exam
B.
Correct the bridge-priority parameter to be identical on both switches.
C.
Configure revision-level 2 on Switch 1.
D.
Correct the configuration-name parameter to be identical on both switches.
Answer: C,D
Explanation:
You are asked to configure a new LSP in your network. The new LSP must take a specific path
using a given set of routers.
A.
A named path must be defined and referenced as primary for the LSP.
B.
A named path must be defined and referenced as preferred for the LSP.
C.
A named path must be defined and given a low priority.
D.
A named path must be defined and given a high priority.
Answer: A
Explanation:
Which three IPv6 addresses are valid equivalents for the address
2001:0000:0000:0000:0134:fc0e:cc8b:458a? (Choose three?)
A.
B.
2001:0:0:0:0134:fc0e:cc8b:458a
C.
2001:0:0:0134:fc0e:cc8b:458a
D.
2001::134:fc0e:cc8b:458a
E.
2001:0::0:134:fc0e:cc8b:458a
Answer: B,D,E
Explanation:
In the exhibit, R1, R2, and R3 are all IBGP peers within AS 65505. R1 receives a BGP
advertisement from an external BGP peer in AS 65555, and a BGP advertisement from R3. The
default BGP advertisement behavior is in effect in this environment.
A.
R1 will advertise the route received from R3 to R2 and its external BGP peer.
B.
R1 will advertise the route received from R3 only to its external BGP peer.
C.
R1 will advertise the route received from its external peer to R2 and R3.
D.
Answer: B,C
Explanation:
Which three statements are true about GRE and IP-IP tunnels? (Choose three.)
A.
All intermediary devices must have reachability to the tunnel endpoints.
B.
Tunnel endpoints must use the loopback interface for reachability.
C.
Tunnel endpoints must have a route that directs traffic into the tunnel.
D.
Tunnel endpoints must have a route to the remote endpoint learned by a dynamic routing protocol.
E.
Tunnel endpoints require a tunnel interface.
Answer: A,C,E
Explanation:
Which two statements are correct about a generated route? (Choose two.)
A.
A generated route requires at least two contributing active routes to be active.
B.
A generated route has a route preference of 150.
C.
The primary contributing route is the route with the lowest preference that falls within the
aggregate range of prefixes.
Answer: C,D
Explanation:
A.
It requires speakers to be configured with BFD.
B.
It uses a virtual router MAC address for LAN communications.
C.
It uses multicast address 224.0.0.18.
D.
It is confined to the local network with a TTL of 255.
E.
It uses the virtual router’s lo0 address for LAN communications.
Answer: B,C,D
Explanation:
A.
"Pass Any Exam. Any Time." - www.actualtests.com 202
Juniper JN0-360 Exam
The configuration supports IPv4 multicast routes.
B.
The configuration supports IPv4 unicast routes.
C.
The configuration supports IPv6 unicast routes.
D.
The configuration supports IPv6 multicast routes.
Answer: C
Explanation:
By default, OSPFv3 supports unicast IPv6 routes, but you can configure OSPFv3 to support
multiple address families. To support an address family other than unicast IPv6, you configure a
realm that allows OSPFv3 to advertise IPv4 unicast, IPv4 multicast, or IPv6 multicast routes.
realm ipv4-unicast {
area 0.0.0.0 {
interface fe-0/1/0.0;
area 0.0.0.0 {
interface fe-0/1/0.0;
References: http://www.juniper.net/documentation/en_US/junos15.1/topics/topic-map/ospfv3-
multiple-address-families.html
You are asked to configure a GRE tunnel between two remote sites to support the exchange of
IPv6 traffic. The two sites are separated by an IPv4 network.
A.
You must enable the GRE interface for IPv6 operations.
B.
You must increase the MTU to no less than 2500.
C.
You must add a static route for the remote IPv6 destination subnet with the remote tunnel endpoint
as the next hop at each site.
D.
You must enable the GRE interface for IPv4 operations.
Answer: C,D
Explanation:
A.
bridge priority
B.
bridge port priority and bridge port address
C.
bridge priority and bridge address
D.
port priority and port address
Answer: D
Explanation:
B.
aggregator
C.
AS path
D.
community
Answer: A,C
Explanation:
Which aggregate route would represent all four routes shown in the exhibit?
A.
10.10.0.0/19
B.
10.10.0.0/21
C.
10.10.0.0/20
D.
10.10.0.0/22
Answer: A
Explanation:
A.
Option A
B.
"Pass Any Exam. Any Time." - www.actualtests.com 206
Juniper JN0-360 Exam
Option B
C.
Option C
D.
Option D
Answer: D
Explanation:
A.
topology
B.
vector
C.
length
D.
value
Answer: C,D
Explanation:
Which two routing protocols make use a designated router, or pseudo node, to represent a
broadcast network? (Choose two.)
A.
BGP
B.
OSPF
D.
IS-IS
Answer: B,D
Explanation:
Your customer requests that you provide a transparent Layer 2 service between two of their
remote locations. This service must allow them to pass tagged traffic from multiple VLANs. You
decide to use Q-in-Q tunneling on the two provider edge MX Series routers that connect to the
customer’s CE devices.
A.
The CE-facing interfaces on the PE devices must be configured as trunk ports.
B.
The CE-facing interfaces on the PE-devices must be configured as access ports.
C.
The PE-facing interfaces on the CE devices must be configured as trunk ports.
D.
The PE-facing interfaces on the CE devices must be configured as access ports.
Answer: B,C
Explanation:
You have multiple Layer 2 interfaces associated with different VLANs configured on an MX Series
router. You have been asked to ensure Layer 3 reachability through the MX Series router for the
subnets associated with the different VLANs.
B.
Use the BPDU protect feature to direct traffic between VLANs.
C.
Use a Layer 2 routing policy to forward traffic between VLANs.
D.
Use filter-based forwarding to direct traffic between VLANs.
Answer: A
Explanation:
A.
A PathTear message is sent downstream.
B.
A PathErr message is sent upstream.
C.
A PathErr message is sent downstream.
D.
A PathTear message is sent upstream.
Answer: A
Explanation:
Which two elements are valid in the BGP path selection algorithm? (Choose two.)
A.
"Pass Any Exam. Any Time." - www.actualtests.com 209
Juniper JN0-360 Exam
lowest local preference value
B.
lowest multi-exit discriminator
C.
highest multi-exit discriminator
D.
highest local preference value
Answer: B,D
Explanation:
Which two formats are valid route distinguisher formats? (Choose two.)
A.
<MPLS label> : <VPN assigned number>
B.
<autonomous system number> : <VPN assigned number>
C.
<inbound interface index> : <VPN assigned number>
D.
<loopback IP address> : <VPN assigned number>
Answer: B,D
Explanation:
Referring to the exhibit, what is required to establish an IS-IS adjacency between these two
routers?
A.
The interface connecting the two routers must be configured as a Level 2 interface.
B.
Both routers will require wide metrics to be enabled.
C.
The interface connecting the two routers must be configured as a Level 1 interface.
D.
Router A must be configured as the designated intermediate system (DIS).
Answer: A
Explanation:
On an MX Series device with dual Routing Engines, which two conditions cause a unified ISSU to
fail? (Choose two.)
A.
Graceful restart is disabled.
B.
BFD is enabled.
C.
GRES is disabled.
D.
NSR is disabled.
Answer: C,D
You are asked to deploy a large-scale IS-IS network with multiple areas.
A.
A collection of Level 1 routers in different areas constitute the backbone in the network.
B.
Level 2 routers can route between areas.
C.
Level 1 routers can route between areas.
D.
A collection of Level 2 routers in different areas constitute the back bone in the network.
Answer: B,D
Explanation:
A.
VRRP
B.
BFD
C.
graceful restart
D.
ISSU
Answer: A
"Pass Any Exam. Any Time." - www.actualtests.com 212
Juniper JN0-360 Exam
Explanation:
Which high availability feature allows uninterrupted packet forwarding and temporary suppression
of all routing protocol updates?
A.
Virtual Router Redundancy Protocol (VRRP)
B.
graceful Routing Engine switchover (GRES)
C.
graceful restart (GR)
D.
nonstop active routing (NSR)
Answer: B
Explanation:
You are using RSVP in your network to signal MPLS LSPs. You are asked to ensure that the
egress MPLS router receives the full label stack, containing both the hop-by-hop and VPN label.
A.
Use the set protocols mpls explicit-null command.
B.
Use the set protocols mpls expand-loose-hop command.
C.
Use the set protocols rsvp keep-multiplier command.
D.
Apply set protocols rsvp interface <interface> no-aggregate to the egress interface.
Answer: A
A.
Use static addressing.
B.
Use neighbor discovery.
C.
Use an auto-configuration based on the interface MAC address.
D.
Use an IPv6 routing protocol.
Answer: A,C
Explanation:
What are two valid statements for virtual switches on MX Series devices? (Choose two.)
A.
Integrating routing and bridging (IRB) interfaces are supported.
B.
Layer 2 interfaces are supported.
C.
Interfaces are inherently loop free.
D.
Trunk interfaces are not supported.
Answer: A,B
Explanation:
Referring to the exhibit, which two statements are correct? (Choose two.)
A.
The routes in inet.0 are imported into user-a.inet.0
B.
The RIB group can be applied to OSPF.
C.
The RIB group cannot be applied to OSPF.
D.
The routes in user-a.inet.0 are imported into inet.0
Answer: B,D
Explanation:
Referring to the exhibit, which static route will be exported into OSPF?
A.
172.29.0.0/16
B.
172.29.0.0/17
C.
172.28.0.0/24
D.
172.29.0.0/24
Answer: D
Explanation:
In the exhibit, which configuration is required to establish a single adjacency between the two IS-
IS routers?
A.
set protocols isis interface xe-0/0/0.0 point-to-point
B.
set protocols isis level 2 wide-metrics-only
C.
set protocols isis interface xe-0/0/0.0 level 1 disable
D.
set protocols isis interface xe-0/0/0.0 level 1 priority 0
Answer: A
Explanation:
In an IS-IS network, Router A is the current DIS with a priority of 64. Router B comes online with a
priority of 100.
A.
Router A remains as the DIS.
B.
Router A remains the DIS and Router B becomes the backup DIS.
C.
Router B becomes the DIS.
D.
Router B becomes the DIS and router A becomes the backup DIS.
Answer: C
"Pass Any Exam. Any Time." - www.actualtests.com 217
Juniper JN0-360 Exam
Explanation:
A.
The RD controls the allocation of MPLS labels within a VRF.
B.
The RD allows different VRFs to contain the same IP prefixes.
C.
The RD is used to create unique routing processes within the global routing instance.
D.
The RD is used to control the import and export of routes within a VRF.
Answer: B
Explanation:
An ISO NET has been configured on R2’s lo0.0 interface and ge-0/0/2.0 has been configured to
run IS-IS. However, IS-IS adjacency on ge-0/0/2.0 is not coming up.
A.
"Pass Any Exam. Any Time." - www.actualtests.com 218
Juniper JN0-360 Exam
Configure the family iso parameter under the ge-0/0/2.0 interface.
B.
Disable Level 2 for interface ge-0/0/2.0
C.
Add the lo0.0 interface under the [edit protocols isis] hierarchy.
D.
Configure the interface priority for ge-0/0/2.0.
Answer: A
Explanation:
You are asked to deploy a large-scale IS-IS network with multiple areas.
A.
A router configured for Level 1 only informs all Level 2 routers in the area of external reachability.
B.
A router configured for Level 1 and Level 2 informs all Level 2 routers in the area of external
reachability.
C.
A router configured for Level 2 only informs all level 1 routers in the area of external reachability.
D.
A router configured for Level 1 and Level 2 informs all Level 1 routers in the area of external
reachability.
Answer: D
Explanation:
In a Junos device functioning as an MPLS transit router, which routing table is used when
performing a forwarding lookup for an incoming packet?
B.
inet.0
C.
inet.3
D.
mpls.0
Answer: C
Explanation:
Referring to the exhibit, MED is being used in your BGP network. All other BGP configurations use
the default settings.
Which statement is correct regarding traffic destined to the 151.213.0.0/16 prefix in AS 358?
A.
A traffic black hole will be created at Router A and Router B.
"Pass Any Exam. Any Time." - www.actualtests.com 220
Juniper JN0-360 Exam
B.
Traffic will load-balance across both the A-to-C and B-to-D paths.
C.
Traffic will prefer the A-to-C path.
D.
Traffic will prefer the B-to-D path.
Answer: C
Explanation:
Referring to the exhibit, four IS-IS routers have been deployed on a multi-access Ethernet
segment. Router C came online first.
After all routers are online, which two statements are true? (Choose two.)
A.
Adjacencies are only formed with designated intermediate system (DIS).
"Pass Any Exam. Any Time." - www.actualtests.com 221
Juniper JN0-360 Exam
B.
Router D is the designated intermediate system (DIS).
C.
Adjacencies are formed between all four routers.
D.
Router C is the designated intermediate system (DIS).
Answer: B,C
Explanation:
For two switches to participate in the same Multiple Spanning Tree Protocol (MSTP) region, which
three values must match? (Choose three.)
A.
extended system ID
B.
region name
C.
member VLAN ID list
D.
root bridge ID
E.
revision number
Answer: A,C,E
Explanation:
In the exhibit, R1 is sending the 172.16.100.0/24 route to R2 through EBGP. R2 has IBGP
sessions to R3 and R4, but they are not installing the route. All BGP sessions are established.
Which two actions would enable R3 and R4 to install the route from R2? (Choose 2.)
A.
Advertise the R1-R2 link into the IGP.
B.
Configure the cluster-id parameter under the R2 IBGP group.
C.
Configure a BGP export policy with a next-hop self action on R2.
D.
Configure an IGP export policy with a next-hop self action on R2.
Answer: A,C
"Pass Any Exam. Any Time." - www.actualtests.com 223
Juniper JN0-360 Exam
Explanation:
What is the correct format for an IPv4 address mapped into IPv6?
A.
::192:168:0:1
B.
::FFFF:192.168.0.1
C.
::FFFE:192:168:0:1
D.
::192.168.0.1:FFFF
Answer: B
Explanation:
You are deploying IS-IS in your network to enable the routing of only IPv6. Assume that the
loopback interface has been properly configured.
What is the minimum required configuration to enable only IPv6 routing in IS-IS?
A.
user@host# show protocols isis
rib-group inet6;
interface ge-0/0/0.0;
interface lo0.0 {
passive;
B.
user@host# show protocols isis
interface ge-0/0/0.0;
interface lo0.0 {
passive;
unit 0 {
family iso;
C.
user@host# show protocols isis
no-ipv4-routing;
interface ge-0/0/0.0
interface lo0.0 {
passive;
unit 0 {
family iso;
D.
user@host# show protocols isis
no-ipv4-routing;
"Pass Any Exam. Any Time." - www.actualtests.com 225
Juniper JN0-360 Exam
interface ge-0/0/0.0;
interface lo0.0 {
passive;
unit 0 {
family iso;
family inet6;
E.
user@host# show protocols isis
traffic-engineering {
family inet6 {
shortcuts;
interface ge-0/0/0.0;
interface lo0.0 {
passive;
unit 0 {
family iso;
Answer: C
Explanation:
Your customer requests that you provide a transparent Layer 2 service between two of their
remote locations. This service must allow the customer to pass tagged traffic from multiple VLANs.
You decide to use Q-in-Q tunneling on the two provider edge MX Series routers that connect to
the customer’s CE devices.
A.
As traffic leaves the Q-in-Q tunnel, the S-VLAN tag will be removed from the frames.
B.
As traffic enters the Q-in-Q tunnel, an S-VLAN tag will be added to the frames.
C.
As traffic enters the Q-in-Q tunnel, a C-VLAN tag will be added to the frames.
D.
As traffic leaves the Q-in-Q tunnel, the C-VLAN tag will be removed from the frames.
Answer: A,B
Explanation:
A.
type length value
B.
link-state
C.
partial sequence number
D.
database description
E.
complete sequence number
Which OSPF LSA type describes the router IDs of ASBR routers located in remote areas?
A.
Type 4
B.
Type 2
C.
Type 3
D.
Type 1
Answer: A
Explanation:
OSPF LSA types:
References: https://networklessons.com/ospf/ospf-lsa-types-explained/
Referring to the exhibit, which two statements are correct? (Choose two.)
A.
Type 2 LSAs are not created for this link.
B.
Type 2 LSAs are created for this link.
C.
Designated router election does not occur on this link.
D.
Designated router election occurs on this link.
Answer: A,C
Explanation:
A: Type 2 - Network LSA - the designated router (DR) on a broadcast segment (e.g. Ethernet) lists
which routers are joined together by the segment. Type 2 LSAs are flooded across their own area
only. The link-state ID of the type 2 LSA is the IP interface address of the DR.
C: Designated router (DR) and BDR election is done via the Hello protocol. Hello packets are
exchanged via IP multicast packets (Appendix B) on each segment. Multicast packets are not sent
References: https://en.wikipedia.org/wiki/Link-state_advertisement
http://www.cisco.com/c/en/us/support/docs/ip/open-shortest-path-first-ospf/7039-1.html#t21
A.
origin
B.
MED
C.
AS path
D.
next hop
E.
local preference
Answer: A,C,D
Explanation:
ORIGIN is a well known mandatory attribute that indicates the origin of the prefix, or rather, the
way in which the prefix was injected into BGP.
References: http://www.informit.com/articles/article.aspx?p=331613&seqNum=5
Your customer requests that you provide a transparent Layer 2 service between two of their
"Pass Any Exam. Any Time." - www.actualtests.com 230
Juniper JN0-360 Exam
remote locations. This service must allow the customer to pass tagged traffic from multiple VLANs.
You decide to use Q-in-Q tunneling on the two provider edge MX Series routers that connect to
the customer’s CE devices.
A.
As traffic enters the Q-in-Q tunnel on the core-facing interface on the ingress PE device, a push
operation is performed.
B.
As traffic passes through intermediary P routers in the Q-in-Q tunnel, a push operation is
performed.
C.
As traffic passes through intermediary P routers in the Q-in-Q tunnel, a swap operation is
performed.
D.
As traffic enters the Q-in-Q tunnel on the core-facing interface on the ingress PE device, a swap
operation is performed.
Answer: A,C
Explanation:
Q-in-Q tunneling adds a service VLAN tag before the customer’s 802.1Q VLAN tags. The Juniper
Networks Junos operating system implementation of Q-in-Q tunneling supports the IEEE 802.1ad
standard.
In Q-in-Q tunneling, as a packet travels from a customer VLAN (C-VLAN) to a service provider's or
data center VLAN (S-VLAN), another 802.1Q tag for the appropriate S-VLAN is added before the
C-VLAN tag. The C-VLAN tag remains and is transmitted through the network. As the packet
leaves the S-VLAN in the downstream direction, the S-VLAN 802.1Q tag is removed.
With the push option, a packet retains its tag and an additional VLAN tag is added.
With the swap option, the incoming tag is replaced with an S-VLAN tag. (This is VLAN translation.)
References: https://www.juniper.net/documentation/en_US/junos12.3/topics/concept/qinq-
tunneling-qfx-series.html
A.
loose hop
B.
static hop
C.
next hop
D.
strict hop
Answer: D
Explanation:
When a strict hop is configured, it identifies an exact path through which the LSP must be routed.
Strict-hop EROs (Explicit Route Objects) specify the exact order of the routers through which the
RSVP messages are sent.
You are adding IPv6 to an existing IPv4 network running OSPF. Your plan is to use OSPFv3 to
route both IPv4 and IPv6 prefixes.
Which configuration will enable OSPFv3 to advertise prefixes for both IPv4 and IPv6?
A.
user@host# show protocols ospf3
realm ipv4-unicast {
area 0.0.0.0 {
interface ge-0/0/0.0;
area 0.0.0.0 {
interface ge-0/0/0.0;
B.
user@host# show protocols ospf3
export ipv4;
area 0.0.0.0 {
interface ge-0/0/0.0;
C.
user@host# show protocols ospf
area 0.0.0.0 {
interface ge-0/0/0.0;
area 0.0.0.0 {
interface ge-0/0/0.0;
D.
user@host# show protocols ospf3
rib-group inet.0;
area 0.0.0.0 {
interface ge-0/0/0.0;
Answer: A
Explanation:
By default, OSPFv3 supports unicast IPv6 routes, but you can configure OSPFv3 to support
multiple address families. To support an address family other than unicast IPv6, you configure a
realm that allows OSPFv3 to advertise IPv4 unicast, IPv4 multicast, or IPv6 multicast routes.
area 0.0.0.0 {
interface fe-0/1/0.0;
area 0.0.0.0 {
interface fe-0/1/0.0;
References: http://www.juniper.net/documentation/en_US/junos15.1/topics/topic-map/ospfv3-
multiple-address-families.html
A.
20
B.
24
C.
16
D.
28
Answer: A
Explanation:
Tunneling increases overhead, because it needs an extra set of IP headers. Typically this is 20
bytes per packet, so if the normal packet size (MTU) on a network is 1500 bytes, a packet that is
sent through a tunnel can only be 1480 bytes big.
References: http://cs.uccs.edu/~scold/iptunnel.htm
An IS-IS router on a broadcast medium has detected its LSDB is missing an LS PDU.
A.
The router will send a CSNP to the router that sent it a PSNP with missing PDUs.
B.
The router will send a link-state request packet to its closest Level 1/Level2 router.
C.
The router will send a PSNP to the router that sent it a CSNP with missing PDUs.
D.
The router will send a link-state request packet to its DIS router.
Answer: C
Explanation:
A Partial SNP (PSNP) is similar to CSNP except that it describes only some LSPs rather than the
entire database. On a P2P network, PSNP is used to acknowledge received LSPs. On a LAN
network, PSNP is used to request missing or latest LSPs.
A.
topology
B.
vector
C.
length
D.
value
The type and length are fixed in size (typically 1-4 bytes), and the value field is of variable size.
These fields are used as follows:
References: https://en.wikipedia.org/wiki/Type-length-value
Which two statements are true regarding the output shown in the exhibit? (Choose two.)
A.
The ge-1/0/0 interface will transmit any outgoing frames associated with VLAN 55 as untagged
frames.
B.
The ge-1/0/0 interface will associate any untagged frames that are received with VLAN 56.
"Pass Any Exam. Any Time." - www.actualtests.com 236
Juniper JN0-360 Exam
C.
The ge-1/0/0 interface will associate any untagged frames that are received with VLAN 55.
D.
The ge-1/0/0 interface will transmit any outgoing frames associated with VLAN 56 as untagged
frames.
Answer: B,D
Explanation:
* You can configure the router to receive and forward single-tag frames, dual-tag frames, or a
mixture of single-tag and dual-tag frames.
To configure the router to receive and forward single-tag frames with 802.1Q VLAN tags, include
the vlan-tagging statement at the [edit interfaces interface-name] hierarchy level:
vlan-tagging;
* You can configure mixed tagging support for untagged packets on a port. Untagged packets are
accepted on the same mixed VLAN-tagged port. To accept untagged packets, include the native-
vlan-id statement and the flexible-vlan-tagging statement at the [edit interfaces interface-name]
hierarchy level:
flexible-vlan-tagging;
native-vlan-id number;
References: https://www.juniper.net/documentation/en_US/junos15.1/topics/usage-
guidelines/interfaces-enabling-vlan-tagging.html
https://www.juniper.net/documentation/en_US/junos12.1x44/topics/concept/security-interface-vlan-
tagging-configuring.html
Which two LSA types would an ABR generate and send into a totally stubby area? (Choose two.)
A.
Type 2 LSA
C.
Type 5 LSA
D.
Type 3 LSA
Answer: A,D
Explanation:
A stub area that only allows routes internal to the area and restricts Type 3 LSAs from entering the
stub area is often called a totally stubby area.
Totally stubby areas can only contain type 1 and 2 LSAs, and a single type 3 LSA.
References: https://www.juniper.net/techpubs/en_US/junos15.1/topics/concept/ospf-stub-areas-
overview.html
A.
If a device configured for RSTP receives STP BPDUs, it sends STP BPDUs.
B.
If a device configured for RSTP receives STP BPDUs, it forwards them as STP BPDUs.
C.
If a device configured for RSTP receives STP BPDUs, it continues to send RSTP BPDUs.
D.
If a device configured for RSTP receives STP BPDUs, it sends RSTP and STP BPDUs.
Answer: B
Explanation:
Enhancements enable RSTP to achieve sub-second forwarding and network convergence. RSTP
is backward-compatible with legacy STP. If legacy STP BPDU is detected on a link, then an
RSTP-capable bridge will revert to legacy STP on that given port.
References: https://www.juniper.net/techpubs/en_US/junos12.3/topics/concept/mx-series-rstp-
"Pass Any Exam. Any Time." - www.actualtests.com 238
Juniper JN0-360 Exam
port-states-roles.html
A.
Adding VLANs to VSTP consumes more CPU resources.
B.
It supports 4093 spanning-tree topologies.
C.
It is compatible with PVST+, but not with PVST.
D.
Different VLANs must use different spanning-tree topologies.
Answer: A
Explanation:
If you use VLANs, , we recommend that you enable MSTP unless your network requires the
device compatibility provided by VSTP. Switches configured to run VSTP automatically assign
each VLAN to one spanning-tree instance that runs RSTP. While this approach is useful to
optimize network usage in small networks with a limited number of VLANs, a VSTP configuration
in a network with several hundred VLANs can overload switch CPUs.
References: http://www.juniper.net/techpubs/en_US/junos13.2/topics/concept/spanning-trees-ex-
series-vstp-understanding.html
Referring to the exhibit, R1 and R2 are unable to form an IS-IS adjacency on interface ge-0/0/1.0.
The ge-0/0/1.0 interface has the appropriate address families enabled.
Which two actions will resolve the problem and allow the adjacency to come up? (Choose two.)
A.
Change the R2 loopback interface address to 49.3154.1111.1111.1111.00.
B.
Enable Level 2 adjacencies on R1.
C.
Enable Level 1 adjacencies on R1.
D.
Change the R2 loopback interface address to 49.3154.2222.2222.2222.00.
Answer: B,D
Explanation:
B: We need to enable level 2 adjacencies on R1, as an L1 adjacency is formed only with routers in
the same area.An L2 adjacency is formed with routers in the same area or a different area.
D: IS-IS uses ISO network addresses. Each address identifies a point of connection to the
network, such as a router interface, and is called a network service access point (NSAP). For
example, the NET address 49.0001.1921.6800.1001.00 consists of the following parts:
49—AFI
0001—Area ID
1921.6800.1001—System identifier
"Pass Any Exam. Any Time." - www.actualtests.com 240
Juniper JN0-360 Exam
00—Selector
Which two statements are correct according to the output shown in the exhibit? (Choose two.)
A.
The peering session can pass inet-vpn routes.
B.
The peering session is enabled for multihop support.
C.
"Pass Any Exam. Any Time." - www.actualtests.com 241
Juniper JN0-360 Exam
The peering session uses an altered route preference.
D.
The peering session is enabled for multipath support.
Answer: A,B
Explanation:
A.
links
B.
DIS
C.
pseudo nodes
D.
routers
Answer: D
Explanation:
IS-IS differs from OSPF in the way that "areas" are defined and routed between. IS-IS routers are
designated as being: Level 1 (intra-area); Level 2 (inter area); or Level 1-2 (both). Routing
information is exchanged between Level 1 routers and other Level 1 routers of the same area, and
Level 2 routers can only form relationships and exchange information with other Level 2 routers.
Level 1-2 routers exchange information with both levels and are used to connect the inter area
routers with the intra area routers.
References: https://en.wikipedia.org/wiki/IS-IS
A.
The configuration supports IPv6 multicast routes.
B.
The configuration supports IPv6 unicast routes.
C.
The configuration supports IPv4 unicast routes.
D.
The configuration supports IPv4 multicast routes.
Answer: B
Explanation:
By default, OSPFv3 supports unicast IPv6 routes, but you can configure OSPFv3 to support
multiple address families. To support an address family other than unicast IPv6, you configure a
realm that allows OSPFv3 to advertise IPv4 unicast, IPv4 multicast, or IPv6 multicast routes.
realm ipv4-unicast {
area 0.0.0.0 {
interface fe-0/1/0.0;
interface fe-0/1/0.0;
References: http://www.juniper.net/documentation/en_US/junos15.1/topics/topic-map/ospfv3-
multiple-address-families.html
A.
f80e::52c5:8d03:e8f6:57c0
B.
fc00::52c5:8d03:e8f6:57c0
C.
2001::52c5:8d03:e8f6:57c0
D.
fe80:0:0:0:52c5:8d03:e8f6:57c0
Answer: D
Explanation:
In the Internet Protocol Version 6 (IPv6), the address block fe80::/10 has been reserved for link-
local unicast addressing. To conform to standard /64 addressing on subnets, the actual link local
addresses are assigned with the prefix fe80::/64. The 54 bits after the most significant ten bits
must be zero.
References: https://en.wikipedia.org/wiki/Link-local_address#IPv6
B.
MED
C.
cluster list
D.
AS path
Answer: B,C
Explanation:
The MUTLI_EXIT_DISC (MED) is an optional non-transitive attribute that provides a mechanism
for the network administrator to convey to adjacent autonomous systems to optimal entry point in
the local AS.
In the exhibit, which configuration is correct when setting up LDP for R1?
A.
set interfaces ge-0/0/0 unit 0 family mpls
B.
set interfaces ge-0/0/0 unit 0 family mpls
C.
D.
set interfaces ge-0/0/0 unit 0 family mpls
Answer: B
Explanation:
Example: In this example, you enable the MPLS family and create an LDP instance on all the
transit interfaces.
References: http://www.juniper.net/documentation/en_US/junos12.1x46/topics/example/mpls-
security-ldp-signaled-lsp-configuring.html
A.
S-VLAN and C-VLAN
B.
"Pass Any Exam. Any Time." - www.actualtests.com 246
Juniper JN0-360 Exam
S-VLAN and D-VLAN
C.
P-VLAN and D-VLAN
D.
P-VLAN and C-VLAN
Answer: A
Explanation:
IEEE 802.1ad is an Ethernet networking standard informally known as QinQ and is an amendment
to IEEE standard IEEE 802.1Q-1998.
The inner tag is the tag which is closest to the payload portion of the frame; it is officially called C-
TAG (Customer tag, with ethertype 0x8100).
The outer tag is the one closer/closest to the Ethernet header; its name is S-TAG (Service tag,
ethertype 0x88a8).
References: https://en.wikipedia.org/wiki/IEEE_802.1ad
You have multiple Layer 3 VPNs supporting your various customers. Some of the customers use
overlapping IP address space.
A.
route target
B.
MP-BGP
C.
BGP communities
D.
route distinguisher
Answer: D
"Pass Any Exam. Any Time." - www.actualtests.com 247
Juniper JN0-360 Exam
Explanation:
A route distinguisher (RD) distinguishes one set of routes (one VRF) from another. It is a unique
number prepended to each route within a VRF to identify it as belonging to that particular VRF or
customer. An RD is carried along with a route via MP-BGP when exchanging VPN routes with
other PE routers.
While troubleshooting IS-IS on a broadcast network with multiple IS-IS routers, you notice that
hello packets from Router A are sent every three seconds while the hello packets from Router B
are sent every nine seconds. Both Router A and Router B are configured with default IS-IS
configuration values.
A.
Router B is a non-DIS router.
B.
Router B is the DIS router.
C.
Router A is the DIS router.
D.
Router A is a non-DIS router.
Answer: A,C
Explanation:
The DIS Router sends CSNPs describing all the LSPs in the database every 3 seconds.
References:
http://www.cisco.com/en/US/products/ps6599/products_white_paper09186a00800a3e6f.shtml
Which two statements correctly describe MPLS penultimate-hop popping (PHP)? (Choose two.)
B.
With PHP enabled, the router upstream from the egress router pops the MPLS label.
C.
In the Junos OS, PHP is enabled by default.
D.
With PHP enabled, the egress router pops the MPLS label.
Answer: B,C
Explanation:
B: In penultimate-hop popping, the final MPLS label is popped from the IP packet at the last
provider router in the network before being forwarded to the PE router. The PE router receives the
packet and checks the IP address, and then the packet is forwarded to its destination.
References:
http://www.juniper.net/documentation/en_US/junos15.1/topics/reference/configuration-
statement/ultimate-hop-popping-edit-protocols-mpls.html
A.
VRRP
B.
BFD
C.
VCCP
D.
ICCP
Answer: D
References: https://www.juniper.net/documentation/en_US/junos14.2/topics/usage-
guidelines/interfaces-configuring-multi-chassis-link-aggregation.html
Which statement is true when a VRRP master owns the VIP address?
A.
The VRRP priority will be set to 128.
B.
The VRRP priority will be set to 100.
C.
The VRRP priority will be set to 0.
D.
The VRRP priority will be set to 255.
Answer: D
Explanation:
Switches configured with VRRP share a virtual IP address, which is the address you configure as
the default route on the hosts. At any time, one of the switches is the VRRP master, meaning that
it owns the virtual IP address and is the active default gateway. The other devices are backups.
The switches dynamically assign master and backup roles based on priorities that you configure (1
through 255). If the master fails, the backup switch with the highest priority becomes the master
within a few seconds. This is done without any interaction with the hosts.
References: http://www.juniper.net/documentation/en_US/junos15.1/topics/concept/vrrp-qfx-
series.html
You are asked to configure and apply a new routing policy to influence routing advertisements
"Pass Any Exam. Any Time." - www.actualtests.com 250
Juniper JN0-360 Exam
sent to a specific EBGP peer. You must ensure that the new policy does not impact routing
advertisements sent to any other peer.
A.
The new policy should be applied as an export policy for the EBGP group in which the peer is
defined.
B.
The new policy should be applied as an import policy for the EBGP group in which the peer is
defined.
C.
The new policy should be applied as an export policy for the specific EBGP peer.
D.
The new policy should be applied as an import policy for the specific EBGP peer.
Answer: A
Explanation:
References: https://www.juniper.net/techpubs/en_US/junos15.1/topics/concept/conditional-prefix-
installing-overview.html
Which two BGP attributes influence traffic coming into an AS? (Choose two.)
A.
local preference
B.
next hop
C.
MED
D.
origin
Answer: A,B
B: The BGP NEXT_HOP is a well-known mandatory attribute. The Next Hop attribute is set when
a BGP speaker advertises a prefix to a BGP speaker outside its local autonomous system (it may
also be set when advertising routes within an AS, this will be discussed in later sections). The Next
Hop attribute may also serve as a way to direct traffic to another speaker, rather than the speaker
advertising the route itself
References: http://www.informit.com/articles/article.aspx?p=331613&seqNum=5
Which OSPF state indicates that the router has finished transmitting its database but is still
receiving database information?
A.
Loading
B.
ExStart
C.
2Way
D.
Exchange
Answer: A
Explanation:
In the loading state, routers send link-state request packets. During the adjacency, if a router
receives an outdated or missing link-state advertisement (LSA), it requests that LSA by sending a
link-state request packet.
Note: OSPF states for adjacency formation are Down, Init, Attempt, 2-way, Exstart, Exchange,
Loading and Full.
Which VPN technology allows remote locations to appear as a single LAN segment?
A.
VPLS
B.
CCC
C.
Layer 3 VPN
D.
L2PT
Answer: A
Explanation:
VPLS is a virtual private network (VPN) technology. A VPLS is a provider service that emulates
the full functionality of a traditional Local area network (LAN). A VPLS makes it possible to
interconnect several LAN segments over a packet switched network (PSN) and makes the remote
LAN segments behave as one single LAN.
Referring to the exhibit, which route preference will be assigned to the route 172.24.0.0/20?
A.
150
B.
170
C.
130
D.
100
Answer: C
Explanation:
If the route is learned through aggregate the default router preference is 130.
aggregate {
defaults {
aggregate-options ...
route destination-prefix {
aggregate-options ...
References:
http://www.juniper.net/documentation/en_US/junos15.1/topics/reference/general/routing-protocols-
default-route-preference-values.html
You have built the core of your network using Spanning Tree Protocol. You must ensure that if one
of the links between your core switches fails to receive BPDUs it does not mistakenly create a
loop.
Which feature would you use to ensure BPDUs are always received from neighboring switches to
indicate that the remote switch is still alive?
A.
storm control
B.
BPDU control
C.
root protection
D.
loop protection
Answer: C
Explanation:
Peer STP applications running on switch interfaces exchange a special type of frame called a
bridge protocol data unit (BPDU). Switches communicate interface information using BPDUs to
create a loop-free topology that ultimately determines the root bridge and which interfaces block or
forward traffic in the spanning tree.
However, a root port elected through this process has the possibility of being wrongly elected. A
user bridge application running on a PC can generate BPDUs, too, and interfere with root port
To prevent this from happening, enable root protection on interfaces that should not receive
superior BPDUs from the root bridge and should not be elected as the root port.
References: http://www.juniper.net/techpubs/en_US/junos15.1/topics/example/spanning-trees-
root-protection-ex-series.html