Professional Documents
Culture Documents
Fiat Barchetta: Auxiliary Units
Fiat Barchetta: Auxiliary Units
Fiat Barchetta: Auxiliary Units
P3WO17HO1 P3WO17HO2
" fJ --
" \
unit (C) through duct (B). Both heater ra-
diaotr inlet and outlet ducts are indicated
by the number (2).
\\
P3WO17HO3
P3WO17H04
Disassembly
-
- working on left side surface of heater dis-
tributor unit, release sheaths of cables (8
and C) from clips (1) and withdraw coils at
cable ends from cylindrical ridges on lever
(2) and rack (3) controlling mixer flap and
distribution flap;
P3WO18HO1
P3WO18HO2
P3WO18HO3
P3WO20HO1
P3WO20HO3 P3WO20HO5
- working through arrowed slot on air intake flap (2), undo fin (3) with toothed profile of lever (4) in
order to withdraw from flap (2) and upper case half (22);
- position air intake flap (2) to release pivot pin from moulded ridges (5) press-fitted on upper case half
(22).
P3WO21 HO:
P3WO21 HI
DISMANTLING HEATER-DISTRIBUTOR
UNIT
- unscrew screws (1) retaining front of
heater radiator (2) to lower rear surface of
heater distributor unit;
- remove radiator (2) from seat on above as-
semblv;
unscrew arrowed screws and screw at the
bottom of hole (3), which joins the two
case halves making up the heater distribu-
tor unit:
- unscrew screws arrowed in bottom central figure, retaining square levers with toothed sector (4 and
5) operating distribution flaps (upper (A) and lower (8» to left side surface of left hand case half;
- firstly withdraw the two levers with toothed sector (4 and 5) from the cylindrical ridges press-fitted on
the above surface, then remove rack (6);
- unscrew screw (7) and withdraw intermediate return lever (8) operating lower distribution flap (8)
from cylindrical ridge on above surface;
- unscrew screw (9) and withdraw square lever (10) operating mixer flap (C) from cylindrical ridge on
above surface:
P3WO22H04
P3WO22HO5
P3WO22HO6 P3WO22HO7
P3WO23HO3
P3WO23HO5
P3WO23HO7
~
Auxiliary units Fiat barchetta
Heater with manual controls
Reassembly
'3WO24HO1
Refitting
To refit the distributor heater assembly, re-
verse operations described for removal. Note
that pipe (6) identified by a green stripe must
be connected to left duct of heater radiator
marked with a raised green dot. Pipe (7)
identified by a white stripe must be connect-
ed to heater radiator duct identified by a
raised white dot.
P3WO24HO3
P3WO24HO4
""
~
--"'
I~
/ """
P3WO25HO1
Disassembly
- disconnect both terminals of leads (7) supplying motor
(8) from connector (9) fitted onto base (2);
- undo plastic moulded blocks (10) fitted on adaptor ring
(11) in order to release from base (2);
- withdraw motor (8) with impeller (12) and adaptor ring
(11) from base (2);
- use a drift to withdraw impeller (12) from shaft of motor
(8), to which it is press-fitted;
~
Auxiliary units Fiat barchetta
Heater with manual controls
HEATER RADIATOR
Removing
- drain engine cooling system
- remove the instrument facia as described in
section 70 of this manual and place on front
seats;
- remove distributor heater assemblyas de-
scribed previously;
- after removing the distributor heater as-
sembly from the vehicle, withdraw the ar-
rowed screws that fasten front part of
heater radiator (1) to vehicle.
A strip of adhesive foam rubber (2) is applied
round the heater radiator and a second seal
(3) of the same material is applied behind the
P3WO26HO2
front part to which are applied the two input
and outlet ducts. Lastly, a thoroid seal (4) of
the same material is applied round the base of
these ducts.
Refitting
P3WO27HO2
5 (B)
r"'-J
P3WO27H04 P3WO27HO5
::r::::-
2
I
~"
~ /
'4 '"
-C).
~
"" I~~::~~~~L:-';
"" '\
y
/'
--
P3WO28HO2
COMPRESSOR - Removing-refitting
1. Drain air conditioning system, then work
from top of engine bay to unscrew screw
-
4 retaining pipe fitting to compressor drain
~\ " duct (A).
.l) 2. Disconnect compressor supply connector
(1), then remove upper compressor re-
~4
1~f/
taining screws.
3. Lift axle, remove right front wheel and
then take off plastic guard in wheel arch to
allow access to air conditioner compres-
~ ~
sor belt tensioner.
4. Move compressor drive belt tensioner
bearing in the arrowed direction to prise
belt off the air conditioner pulley.
~
~I
~
~
Fiat barchetta Auxiliary units
Air conditioner with manual controls
50.
P3WO29HO1
CONDENSER - Removing-refitting
3. Drain air conditioning system, then re-
move resonator by undoing screws shown
in the figure.
4. Remove air duct by undoing clip and fas-
tenings shown in figure.
111\
\\
~==:=:
,~-==:::\
\
\
~
\
\ \\
\\ fL \ <
~~
I
-=
P3WO30HO1
""
1. Unscrew nuts retaining the car alarm con-
3 rJl
~ trol unit/siren and position siren to one
side in engine bay without disconnecting
electrical connections.
2. Disconnect bracket retaining battery to
holder, then remove battery from engine
0 -I bay.
3. Disconnect battery holder by undoing fas-
tenings shown in figure.
nT fd 4. Disconnect air intake duct by undoing
fastenings shown in figure.
6. Unscrew screws retaining air cleaner
bracket and nut retaining line connecting
compressor to evaporator.
P3WO30HO5
2 ~ \\A\ 1"
\1
~
~
"
~=
'J.=
~-I'
5===::::::=:====-
~
"(!)
P3WO31 HO2
P3WO31 HO1
3
1. Unscrew upper screws retaining fans to
radiator unit and disconnect connections.
2. Raiselift and work on lower part of engine
bay. Loosen screw (1) retaining radiator
) ' ~ support beam so that radiator is slightly
lowered and air cleaner assemblycan be
'L-!-
removed after releasing electrical leads
from the unit.
3. Unscrew both screws retaining compres-
sor connection line to evaporatorfrom ra-
diator assemblybeam.
4. Unscrew lower fan retaining screws,then
take out assembly.
,~~
~
. . !!. j
. r
2
11\
,,-, ,
"'::::::"
"
~:0
I
'-
P3WO32HO1
P3WO32HO3
~
Auxiliary units
Air conditioner with manual controls
P3WO17HO1
P3WO35HO2
Disassembly
- withdraw the end spirals of the two cables
(3) from the cylindrical ridges on rack (1)
and lever (2) and release the ends of the
cable sheaths from the clips arrowed in the
central figure;
- disconnect the supply cable connectors of
passenger compartment ventilation fan
speed selector (4), from socket (5) on
printed circuit of compressor activation
switches and passenger compartment air
intake selection and lastly from switch (6)
connected to control symbol light bulbs;
P3WO35HO5
P3WO36HO2
release electrical wiring from hook clips (indicated by small arrows) applied to the above assembly;
unscrew screw (19) that fastens bracket (20) retaining the two pipes (21) connected to the expan-
sion valve and evaporator outlet duct to rear assembly surface;
unscrew screws indicated by large arrows in the various figures on this page that fasten the central
evaporator unit (A) to fan (8) and distributor heater (C).
P3WO36HO4
P3WO37HO2 P3WO37HO3
@ ' "
~ L
~
v
~
I
/
I
'-J
@
P3WO37HO6
P3WO38HO3
P3WO38HO5 P3WO38HO6
P3WO39HO2 P3WO39HO3
P3WO39HO1
- partly detach adhesive foam rubber strip that fastens the two
pipes (7 and 12) connected to outlet duct (9) and expansion
valve (6) to the side of evaporator (10);
P3WO39HO7
DISMANTLINGHEATER-DISTRIBUTORUNIT
- unscrew screws (1) that fasten front part of heater radiator (2) to bottom rear surface of distributor
heater unit;
- remove radiator (2) from seat on the above unit;