Professional Documents
Culture Documents
Mobile Monitoring Tool User Manual iOS
Mobile Monitoring Tool User Manual iOS
1
AS0096-1
Introduction
This manual explains how to use “Daikin AC Monitoring Tool ” app running on
iOS devices. For instruction of PC version software, please refer to user guide for
PC version software.
This app supports iOS version 7 or later.
To monitor operation data, it is necessary to use with “Wireless Adapter” (model:
BTSC/i2S). For instruction guide of BTSC/i2S, please refer to user guide of
BTSC/i2S.
To communicate through BTSC/2S from this app, Bluetooth communication is
used. When using BTSC/2S, please keep turning on Bluetooth function of your
device.
Support model of this app is same as PC version software.
Supported
products
Daikin AC Monitoring Tool Type 3 Checker
* Exceptions may apply (even though applicable to this condition, some models do not support
Daikin Air Conditioner Monitoring Tool protocol). VRVII MA (M9) series are not supported.
** Version 1.0.X app does not support indoor units with 43 or higher address.
2
AS0096-1
1. Connection procedure
Connection harness
(5 pin or 7 pin)
BTSC/i2S
CAUTION
In case of disconnection of Bluetooth communication between BTSC/i2S and iOS device,
you need to return to main screen of App and repeat connection procedure.
(communication would not be restored automatically even if your device will enter the
range of Bluetooth connection.)
Bluetooth connection range is approximately 5 meters
App icon
CAUTION
If “Daikin AC Monitoring Tool” app cannot be found in App store (no corresponding App
has been registered), BTSC/i2S is not certified* in your country (or region, district) or App
has not been yet open to the public.
•Using devices without correct certification is prohibited by law, please be careful.
3
AS0096-1
3. App common settings (options)
App icon
(1)
(2)
4
AS0096-1
4. Main menu
(2)
(3)
(1)
In the bottom of main menu, there are 3 buttons which corresponds to some
buttons of PC version software (indicated as number (1) to (3) in above picture)
There is no “Exit” button, please use home button of your device to exit from App.
5
AS0096-1
5. Common settings (options)
(6)
Recording period setting
By tap “00hours00minutes” in
period setting, recording
period setup screen appears.
Duration can be set up to
23 hours 59 minutes.
(6)
(4)
(5)
(1)
(2)
6
AS0096-1
6. How to record data (1/3) How to pair with BTSC
[CAUTION]
If you have multiple BTSC
paired, it is very difficult to tell
apart each “BTSC”. Cautions
to multiple paired BTSC case
will be explained in
“Appendix”.
PIN code is requested upon After confirming BTSC is listed in Connected BTSC is listed, then
pairing, enter “3131” and tap “MY DEVICES”, tap desired BTSC tap BTSC to proceed to next step.
“Pair” (All BTSC uses same PIN) to connect. Then go back to App
and tap “Recording” button on
home screen.
7
AS0096-1
6. How to record data (2/3) How to assign product
Select correct product type, then tap It could take approximately 1 Successful detection results in a
the connect button (under Product minute to complete protocol detected Protocol and amount
Type) to detect protocol (for Altherma, detection (wait time is longer of Indoor units .
hydro select always Altherma (auto
select does not work)
than PC version).
Editable items
Then select Data label file by Select correct model/series If necessary, correct “Customer
pressing “Unselected” to find ID”, “System name” and “Model”
Data label to use (DEFAULT and tap OK.
works for all Split products)
8
AS0096-1
6. How to record data (3/3) How to start your recording
[CAUTION]
It could take 10-20 seconds
until operation data will be
displayed (wait time is longer
than PC version).
Now you are connected to the Tap “Yes” to start recording While recording, “Rec” icon turns
unit and able to see operation from gray to red
data. To start recording, tap on
the “Recording” icon to proceed.
CAUTION
When connecting to Split
outdoor unit, app cannot
detect protocol type if
outdoor unit is in “standby
electricity saving mode.” In
case of turned off outdoor
unit LED, please switch on
indoor unit by remote
controller to cancel “standby
electricity saving mode.”
To stop recording, tap “Stop” icon. Then tap Yes to stop recording.
9
AS0096-1
7. Option button in record mode (while not recording)
While not recording, you can Select desired items to change Select number of columns of
change settings by tapping the data to be displayed
“Options” icon
Select address of indoor unit In case of hiding indoor Same as Common settings menu,
which needs to be hidden units (address 1, 3) you can change recording
option here
10
AS0096-1
7. Option button in record mode (while not recording)
11
AS0096-1
8. How to playback recorded data
Tap Play icon to enter playback Tap desired item to see data Tap anywhere in the chart area
mode to show “timescale arrow”
12
AS0096-1
8. How to playback recorded data
To see a graphical view of your The top part of the screen makes The “Analog” tap allows you to
recording, tap the “Graph” icon it possible to customize the add or remove data.
graph.
To extend the time range, tap To change the scale of a reading, The “Legend” tap allows you to
on “X-axis” tap “Y-axis” check which reading
corresponds to which color.
13
AS0096-1
8. How to playback recorded data
14
AS0096-1
8. How to playback recorded data
15
AS0096-1
9. How to send data to other person
Edit
[Caution]
Upon sending multiple data,
email attachment files
(compressed files) will be
created per customer ID. (If all
selected data belongs to same
customer ID, only one file will
be created and attached)
Tap the “Edit” icon to enter edit Tap check box on the left of Tap the “Send” icon to proceed
mode in Play menu desired data to be sent
Sent
Tap Yes to proceed New email edit screen will Tap Yes to mark data as “sent”, if
appear with data attached. not please tap No to proceed
Please send data.
16
AS0096-1
10. How to delete recorded data
Tap the “Edit” icon to enter edit Tap check box on the left of Tap the “Waste bin” icon to
mode desired data to delete delete
17
AS0096-1
11. How to edit recorded data (add sent date/time)
In record data list, tap Edit button to enter edit mode then tap particular data to enter
individual data edit screen. In this screen, add/remove data sent date/time information.
Tap the “Edit” icon to enter edit Tap data name to which you Tap slide switch to select on/off
mode want to add sent date/time. of send date/time information.
[CAUTION]
Date/time of switch being
turned on will be added. This
value cannot be changed.
18
AS0096-1
Appendix. Cautions to working with multiple paired BTSC
Your paired BTSC will be listed as identical name of “BTSC” in Bluetooth settings menu of
iOS device. To connect to desired BTSC, please follow the below procedure.
Normally you can physically identify your BTSC by “serial number printed in
the back. If you have 3pcs of BTSC and would like to use all of them at the
same time with 3 iOS devices which has already paired with all of 3 BTSC,
you need to follow below procedure.
19