Professional Documents
Culture Documents
IMS PEI Training Final Quiz (NLNG Aug 2021) (Preview) Microsoft Forms
IMS PEI Training Final Quiz (NLNG Aug 2021) (Preview) Microsoft Forms
Aug 2021)
Please complete the quiz to test your IMS PEI knowledge. The quiz consists of both theoretical
questions and exercises in IMS. Please use the same INSP## ID used this week during the training.
Where links are requested, copy and paste the IMS link from your browser
* Required
Participant Details
Name *
INSP## ID *
Email *
8/12/2021
Theoretical Exercises
For one specific circuit, what is the maximum number of Measurement Sets that
can exist in the “Draft” status?
(2 Points)
As many as desired
8/12/2021
7
What are four things you can do from the Equipment Details page?
(2 Points)
Over the last 30 years, a specific CML has had 8 thickness readings with no (zero)
warnings or errors. To calculate the long and short corrosion rates, how many of
these thickness readings (in total) are used in these calculations?
(2 Points)
CIRCUIT IF
8/12/2021
10
What is the default suggested corrosion rate for Equipment Group PIPING?
11
12
A Class 2 piping circuit has 20 active CMLs. What is the minimum number of
CMLs that should be inspected without getting a “PERF IF penalty”?
(2 Points)
15
10
20
8/12/2021
13
When thickness readings are taken at a very short interval, the prior reading will
be considered a “Time Error” and will not be used in the calculations. The “Time
Error” takes effect when thickness readings are taken less than:
(1 Point)
14
Greater than 10% thicker than any previous reading and less than 15% thicker than a non-
adjacent reading
Greater than 10% thicker than the previous (adjacent) reading or greater than 15% thicker
than a non-adjacent reading
8/12/2021
15
What does not apply when the Renewal/Baseline checkbox in the measurement
set is selected?
(1 Point)
8/12/2021
Navigation Exercises - Equipment ID INSPxx-C-100
16
17
18
8/12/2021
Navigation Exercises
Answer the following questions for the items in the same IMS training site
used this week
19
20
For Equipment ID INSPxx-AC-204, how many Active CMLs are assigned to Circuit
B?
(1 Point)
21
8/12/2021
22
(1 Point)
8/12/2021
Navigation Exercises - Equipment ID INSPxx-AC-200
23
24
25
26
8/12/2021
Navigation Exercises - Unit INSPxx-DISTILLING
27
28
How many schedules are not final approved for more than 1 year at your INSPxx-
DISTILLING unit?
(2 Points)
29
8/12/2021
30
Determine how many active schedules on ACTIVE equipment are due in your
INSPxx-DISTILLING unit during the current calendar year in order to provide the
report to operations and maintenance planning.
(2 Points)
31
8/12/2021
Practical Exercises - Hierarchy and Measurements
8/12/2021
32
B. Circuit “B” along with measurements, have already been added and calculated in
IMS.
C. Create a Measurement Set, enter the thickness readings for Circuit “A” and
calculate.
Please provide the URL for each of the circuits (copy and paste to the text box
below)
(8 Points)
8/12/2021
Circuit Calculation Results
Fill in the following table based on Circuit A and Circuit B calculated in the previous section
33
34
35
8/12/2021
36
37
38
39
8/12/2021
40
41
42
43
8/12/2021
44
8/12/2021
Condition History
45
Create a turnaround event with date (one year from today) at INSPxx-DISTILLING.
Copy and paste the link from IMS here
46
Nozzle N-4 was corroded and replaced in kind. The remaining wall thickness was
only 0.381 cm / 0.15 in. Nozzles N-2 and N-3 were also corroded but are estimated to
make the next turnaround.
(15 Points)
Copy and paste the link from IMS to here
8/12/2021
47
The RAM criticality for this equipment is Medium. This pipe was part of the RBI process
and the mechanism was expected.
The leak was clamped. The elbow should be replaced by 1/Feb/2022. The total impact of
this leak was USD 110,000 (USD 10,000 to perform the repairs, and USD 100,000 process
loss).
(15 Points)
Copy and paste the link from IMS to here
8/12/2021
Schedules, Components, Specifications
48
(4 Points)
Copy and paste the link from IMS to here
49
8/12/2021
50
At Equipment Level:
PWHT: Yes
(3 Points)
Copy and paste the link from IMS to here
This content is neither created nor endorsed by Microsoft. The data you submit will be sent to the form owner.
Microsoft Forms
8/12/2021