Professional Documents
Culture Documents
Chap3 HW2 Solution
Chap3 HW2 Solution
Chap3 HW2 Solution
5
Solution:
Known quantities:
Circuit shown in Figure P3.5 with mesh currents: I1 = 5 A, I2 = 3 A, I3 = 7 A.
Find:
The branch currents through:
a) R1,
b) R2,
c) R3.
Analysis:
a) Assume a direction for the current through R1 (e.g., from
node A to node B).
I R1 = I1 − I 3 ( I 3 has the opposite direction to I R1 )
I R1 = I1 − I 3 = −2 A
“ – ” means that the assumed direction of the current through R1 is not correct.
b) Assume a direction for the current through R2 (e.g., from node B to node A).
I R2 = I 3 − I 2 = 4 A
The assumed direction of the current through R2 and the direction of I3 are the same.
c) Only one mesh current flows through R3. If the current through R3 is assumed to flow in the same direction,
then:
I R1 = I 3 = 7 A .
Problem 3.11
Solution:
Known quantities:
The voltage source value, 3 V, and the five resistance values, indicated in Figure P3.11.
Find:
The current, i, drawn from the independent voltage source using node voltage analysis.
Analysis:
n=4, m=1, Total number of variables: n-1-m = 2: two nodes and two equations for node 1 and 2
At node 1:
3 − v1 v1 v1 − v 2 0.75 Ω
i = i A + iB → = + → 3 = 4v1 − 2v 2 v = 3V
0.5 0.5 0.25
iB
At node 2:
iC
v1 − v2 v
i B = 0. 5 + i C → = 2 + 0.5 → 3v1 − 4v2 = 0.5 × 0.75
0.25 0.75 iA
Problem 3.12
Solution:
Known quantities:
Circuit shown in Figure P3.12.
Find:
Power delivered to the load resistance.
Analysis:
n=4, m=1, Total number of variables: n-1-m = 2: two nodes and two equations for node 1 and 2
KCL at node 1:
V V -(V + V )
I S = i A + i B → 1 + 1 s 2 = 0.5 Or 3 V1 - V2 = 6 ( Eq. 1)
RI RV
iB iD
KCL at node 2:
V -(V + V ) V V2 iC
i B = iC + i D → 1 s 2 = 2 +
RV R1 (R2+R L ) iA
Or 14 V2- 4 V1 = -16 ( Eq. 2) ground
substitute Eq. 1 into Eq. 2 V2 = − 12 / 19 Volt = -0.6316Volt
Problem 3.27
Solution:
Known quantities:
The values of the resistors and of the v
voltage source in the circuit of Figure
P3.27.
Find:
The current i through the resistance
R 4 mesh current analysis.
Analysis:
n=3, m=1, Total number of variables: n-m = 2.
For mesh (a): KVL
− 5.6 + 50ia + 1200(ia − ib ) = 0 → ia (50 + 1200) + ib (− 1200) = 5.6
For meshes (b) and (c): KVL
330ib + 1200(ib − ia ) + v(= 440ic ) = 0 → ia (− 1200) + ib (1200 + 330) + ic (440) = 0
For the current source: KVL -> constitutive equation
i c − i b = 0.2v x = 0.2 (1200 (i a − i b )) = 240 (i a − i b )
Solving,
i a = 136 mA , i b = 137 mA and i c = −106 mA .
Therefore,
i = i c = −106 mA .
Problem 3.41
Solution:
Known quantities:
The values of the current source, of the voltage source and of +
the resistors in the circuit of Figure P3.41:
I B = 12A RB = 1Ω VG = 12 V RG = 0.3Ω R = 0.23Ω
Find:
The voltage across R1 using superposition.
Analysis:
Specify a ground node and the polarity of the voltage across R. Suppress the voltage source by replacing it with
a short circuit. Redraw the circuit.
1 1
R R IB
By current dividers: I R = I B → VR − I = IBR = = 1.38 V
1 1 1 1 1 1 1 1 1
+ + + + + +
R B RG R RB RG R RB RG R
Problem 3.59
Solution:
Known quantities:
Circuit shown in Figure P3.59.
Find:
Value of resistance Rx
Analysis:
R Rx
a) We have Vab = Va -Vb = VS - VS
R+R R+Rx
1 Rx
Vab = VS - VS
2 R + Rx
b) For R = 1 kW , Vs = 12 V , Vab = 12 mV ,
Rx
0.012 = 6- 12 Rx = 996Ω
1000+Rx
Problem 3.73
Solution:
Known quantities:
The values of the voltage and of the resistor in the equivalent
circuit of Figure P3.73: VT = 12V; RT = 8Ω
Assumptions:
Assume the conditions for maximum power transfer exist.
Find:
a. The value of RL .
b. The power developed in RL .
c. The efficiency of the circuit, that is the ratio of power absorbed by the load to power supplied by the source.
Analysis:
a. For maximum power transfer: RL = RT = 8Ω
b. VD: VRL =
RL
VT =
(8) (12) = 6V
RT + R L 8+8
V 2 RL (6)
2
PRL = = = 4.5 W
RL 8
P0 PRL I 2R RL
c. η= = = 2 S L2 = = 0.5 = 50%
PS PRT + PRL I S RT + I S RL RT + R L