Professional Documents
Culture Documents
Ba75863e14 3410 Multi
Ba75863e14 3410 Multi
Multi 3410
Digital pH / D.O. /
conductivity meter
for a digital IDS sensor
ba75863e14 12/2011
Multi 3410
Accuracy when The use of advanced technology and the high quality standard of our instru-
going to press ments are the result of a continuous development. This may result in differ-
ences between this operating manual and your meter. Also, we cannot
guarantee that there are absolutely no errors in this manual. Therefore, we
are sure you will understand that we cannot accept any legal claims resulting
from the data, figures or descriptions.
2 ba75863e14 12/2011
Multi 3410 Contents
1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.1 Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.2 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.3 Socket field . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.4 Automatic sensor recognition . . . . . . . . . . . . . . . . . . . . . 12
1.5 IDS sensors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.6 IDS adapter for analog sensors . . . . . . . . . . . . . . . . . . . 13
2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.1 Authorized use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.2 General safety instructions . . . . . . . . . . . . . . . . . . . . . . . 16
3 Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.1 Scope of delivery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.2 Power supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.3 Initial commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.3.1 Inserting the rechargeable batteries. . . . . . . . . . 19
3.3.2 Connecting the power pack / charging the
batteries ............................ 20
3.3.3 Switching on the meter. . . . . . . . . . . . . . . . . . . . 21
3.3.4 Setting the date and time . . . . . . . . . . . . . . . . . 22
4 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.1 Switching on the meter . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.2 Login with a user name . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.3 General operating principles . . . . . . . . . . . . . . . . . . . . . . 26
4.3.1 Operating modes . . . . . . . . . . . . . . . . . . . . . . . . 26
4.3.2 Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4.3.3 Example 1 on navigation: Setting the language. 29
4.3.4 Example 2 on navigation: Setting the date and
time ................................ 31
4.4 Sensor-independent settings . . . . . . . . . . . . . . . . . . . . . 33
4.4.1 Système . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
4.4.2 Mémoire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.4.3 Automatic Contrôle de stabilité . . . . . . . . . . . . . 35
4.4.4 Automatic switch-off . . . . . . . . . . . . . . . . . . . . . . 35
4.4.5 Display illumination . . . . . . . . . . . . . . . . . . . . . . 35
ba75863e14 12/2011 3
Contents Multi 3410
4 ba75863e14 12/2011
Multi 3410 Contents
4.12 Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
4.12.1 Resetting the measurement settings. . . . . . . . . 96
4.12.2 Resetting the system settings . . . . . . . . . . . . . . 98
8 Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
ba75863e14 12/2011 5
Contents Multi 3410
6 ba75863e14 12/2011
Multi 3410 Overview
1 Overview
The compact, digital precision meter Multi 3410 enables you to carry
out pH measurements, ORP measurements, conductivity measure-
ments and dissolved oxygen (D.O.) measurements quickly and reliably.
The Multi 3410 provides the maximum degree of operating comfort,
reliability and measuring certainty for all applications.
The Multi 3410 supports you in your work with the following functions:
proven calibration procedures
automatic stability control (AR),
automatic sensor recognition,
CMC (continuous measurement control)
QSC (sensor quality control).
1 Keypad
2 Display
3 Socket field
ba75863e14 12/2011 7
Overview Multi 3410
The two USB interfaces (USB-A and USB-B) enable you to:
Transmit data to
– a USB memory device
– a PC
Update the meter firmware.
1.1 Keypad
F1 F2
CAL AR
MENU
ENTER
Multi 3410
AR
<AR> Freezes the measured value (HOLD function)
Switches the AutoRead measurement on or off
8 ba75863e14 12/2011
Multi 3410 Overview
1.2 Display
3 4
6
1
Info 22.09.2009 08:00 7
1 Status information
2 Measured value (with unit)
3 Measured parameter
4 Continuous measurement control (CMC function)
5 Sensor symbol (calibration evaluation, calibration interval)
6 Measured temperature (with unit)
7 Softkeys and date + time
ba75863e14 12/2011 9
Overview Multi 3410
10 ba75863e14 12/2011
Multi 3410 Overview
5 1 2 3 4
Connectors:
1 Digital sensors
(pH, ORP, conductivity, D.O.)
2 Power pack
3 USB-A (host) interface
4 USB B (device) interface
5 Service interface
CAUTION
Only connect sensors to the meter that cannot return any voltages
or currents that are not allowed (> SELV and > current circuit with
current limiting).
WTW IDS sensors and IDS adapters meet these requirements.
ba75863e14 12/2011 11
Overview Multi 3410
In digital IDS sensors, sensor data are stored that clearly identify the
sensor.
The sensor data are automatically taken over by the meter.
Note
Information on available IDS sensors is given on the Internet and in
the WTW catalog, "Laboratory and field instrumentation".
12 ba75863e14 12/2011
Multi 3410 Overview
Sensor data from IDS IDS sensors transmit the following sensor data to the meter:
sensors SENSOR ID
– Sensor name
– Sensor series number
Calibration data
– Calibration date
– Calibration characteristics
– Calibration interval
– Selected buffer set (IDS pH sensors only)
– Cell constant (IDS conductivity sensors only)
– Calibration history of the last 10 calibrations
Measurement settings (IDS conductivity sensors only)
– The set measured parameter
– The set reference temperature
– The set temperature coefficient
– The set TDS factor
The calibration data are updated in the IDS sensor after each calibra-
tion procedure. A message is displayed while the data are being
updated in the sensor.
Note
In the measured value display, you can display the sensor name and
series number of the selected sensor with the [Info] softkey. You can
then display all further sensor data stored in the sensor with the [More]
softkey.
Note
Information on available IDS adapters is given on the Internet and in
the WTW catalog, "Laboratory and field instrumentation".
Detailed information on the IDS adapter is given in the operating man-
ual of the adapter.
ba75863e14 12/2011 13
Overview Multi 3410
14 ba75863e14 12/2011
Multi 3410 Safety
2 Safety
This operating manual contains basic instructions that you must follow
during the commissioning, operation and maintenance of the meter.
Consequently, all responsible personnel must read this operating man-
ual before working with the meter.
The operating manual must always be available within the
vicinity of the meter.
Target group The meter was developed for work in the field and in the laboratory.
Thus, we assume that, as a result of their professional training and
experience, the operators will know the necessary safety precautions
to take when handling chemicals.
Safety instructions Safety instructions in this operating manual are indicated by the warn-
ing symbol (triangle) in the left column. The signal word (e.g. "Caution")
indicates the level of danger:
WARNING
indicates instructions that must be followed precisely in order to
avoid possibly great dangers to personnel.
CAUTION
indicates instructions that must be followed precisely in order to
avoid the possibility of slight injuries or damage to the meter or
the environment.
Further notes
Note
indicates notes that draw your attention to special features.
Note
indicates cross-references to other documents, e.g. operating manu-
als.
ba75863e14 12/2011 15
Safety Multi 3410
Function and The smooth functioning and operational safety of the meter can only be
operational safety guaranteed if the generally applicable safety measures and the specific
safety instructions in this operating manual are followed during opera-
tion.
The smooth functioning and operational safety of the meter can only be
guaranteed under the environmental conditions that are specified in
chapter 7 TECHNICAL DATA.
CAUTION
The meter is only allowed to be opened by authorized personnel.
16 ba75863e14 12/2011
Multi 3410 Safety
Safe operation If safe operation is no longer possible, the meter must be taken out of
service and secured against inadvertent operation!
Safe operation is no longer possible if the meter:
has been damaged in transport
has been stored under adverse conditions for a lengthy period of
time
is visibly damaged
no longer operates as described in this manual.
If you are in any doubt, please contact the supplier of the meter.
Obligations of the The purchaser of this meter must ensure that the following laws and
purchaser guidelines are observed when using dangerous substances:
EEC directives for protective labor legislation
National protective labor legislation
Safety regulations
Safety datasheets of the chemical manufacturers.
CAUTION
In addition to the safety instructions mentioned here, also follow
the safety instructions of the sensors used.
The operating manuals of the sensors are available on the sup-
plied CD and on the Internet under www.WTW.com.
ba75863e14 12/2011 17
Safety Multi 3410
18 ba75863e14 12/2011
Multi 3410 Commissioning
3 Commissioning
3.1 Scope of delivery
Meter Multi 3410
4 NiMH rechargeable batteries 1.2 V Mignon type AA
USB cable (A plug on mini B plug)
Power pack
Short instructions
Detailed operating manual (4 languages)
CD-ROM
ba75863e14 12/2011 19
Commissioning Multi 3410
CAUTION
Make sure that the poles of the rechargeable batteries are posi-
tioned correctly.
The ± signs on the batteries must correspond to the ± signs in the
battery compartment.
4 Close the battery compartment (2) and tighten the screws (1).
CAUTION
The line voltage at the operating site must lie within the input volt-
age range of the original power pack (see section 7.1).
CAUTION
Use original power packs only (see section 7.1).
CAUTION
The batteries in the battery compartment are automatically
charged when the power pack is connected.
Make sure that only NiMH rechargeable batteries are in the battery
compartment. The charging process is optimized for NiMH re-
chargeable batteries. Other battery types can cause damage dur-
ing the charging process.
20 ba75863e14 12/2011
Multi 3410 Commissioning
1 Connect the plug of the power pack to the socket for the power
pack on the Multi 3410.
2 Connect the original power pack to an easily accessible power
outlet.
Note
Charge the batteries completely prior to putting the meter into operation
for the first time. The charging process takes approx. 10 hours. The
symbol is displayed if the batteries are nearly discharged.
Note
The meter has an energy saving feature to avoid unnecessary power
consumption during battery operation.
The energy saving feature switches off the meter during battery opera-
tion if no key is pressed during the adjusted interval. (How to set the
switch-off interval, see section 4.4).
The switch-off interval of the energy saving feature is not active when
the meter is supplied with power via the power pack or the USB-B
cable.
ba75863e14 12/2011 21
Commissioning Multi 3410
22 ba75863e14 12/2011
Multi 3410 Operation
4 Operation
4.1 Switching on the meter
Switching on Press the <On/Off> key.
The meter performs a self-test.
The display shows the manufacturer's logo while the self-test is being
performed.
If a sensor is connected, the measured value display appears.
All user names entered by the administrator are listed in the Nom d'util-
isateur menu. The administrator determines for each user whether or
not a password is required for login to the meter.
ba75863e14 12/2011 23
Operation Multi 3410
Login
User name Admin
Password ####
Change password
22.09.2009 08:00
Note
The login is done immediately if no password is required.
If a sensor is connected the measured value display appears.
4 If a password is required:
Using <><>, enter the Mot de passe menu item and con-
firm with <MENU/ENTER>.
Note
The user specifies the password when he or she first logs in with a user
name.
A valid password consists of 4 digits.
The user can change the password with the next login.
24 ba75863e14 12/2011
Multi 3410 Operation
Changing the password If the administrator has set up the access with password protection:
ba75863e14 12/2011 25
Operation Multi 3410
Operating elements, An overview of the operating elements and the display is given in sec-
display tion 1.1 and section 1.2.
Operating modes, An overview of the operating modes and navigation of the Multi 3410 is
navigation given in section 4.3.1 and section 4.3.2.
26 ba75863e14 12/2011
Multi 3410 Operation
4.3.2 Navigation
Menus and dialogs The menus for settings and dialogs in procedures contain further sub-
menus. The selection is made with the <><> keys. The current
selection is displayed with a frame.
Submenus
The name of the submenu is displayed at the upper edge of the
frame. Submenus are opened by confirming with <MENU/ENTER>.
Example:
System
General
Interface
Clock function
Service information
Reset
22.09.2009 08:00
Settings
Settings are indicated by a colon. The current setting is displayed on
the right-hand side. The setting mode is opened with <MENU/
ENTER>. Subsequently, the setting can be changed with <><>
and <MENU/ENTER>. Example:
General
Language: Deutsch
Acoustic signal: Off
Volume 9
Illumination: On
Brightness: 12
Switchoff time: 1h
Temperature unit: °C
Stability control: On
22.09.2009 08:00
ba75863e14 12/2011 27
Operation Multi 3410
Functions
Functions are designated by the name of the function. They are
immediately carried out by confirming with <MENU/ENTER>. Exam-
ple: Display the Protocole de calibration function.
pH
Calibration record
Calibration data storage
Buffer: TEC
Single-point calibration: Yes
Calibration interval: 7d
Unit for slope: mV/pH
22.09.2009 08:00
pH
Calibration record
Calibration data storage
Buffer: TEC
Single-point calibration: Yes
Calibration interval: 7d
Unit for slope: mV/pH
22.09.2009 08:00
Note
The principles of navigation are explained in the two following sections
by reference of examples:
Setting the language (section 4.3.3)
Setting the date and time (see section 4.3.4).
28 ba75863e14 12/2011
Multi 3410 Operation
22.09.2009 08:00
ba75863e14 12/2011 29
Operation Multi 3410
System
General
Interface
Clock function
Service information
Reset
22.09.2009 08:00
General
Language: Deutsch
Acoustic signal: Off
Illumination: On
Kontrast: 50 %
Switchoff time: 1h
22.09.2009 08:00
General
Language: Deutsch
Acoustic signal: Off
Illumination: On
Brightness: 50 %
Switchoff time: 1h
22.09.2009 08:00
30 ba75863e14 12/2011
Multi 3410 Operation
The measuring instrument has a clock with a date function. The date
and time are indicated in the status line of the measured value display.
When storing measured values and calibrating, the current date and
time are automatically stored as well.
The correct setting of the date and time and date format is important for
the following functions and displays:
Current date and time
Calibration date
Identification of stored measured values.
Note
After a fall of the supply voltage (empty batteries), the date and time are
reset to 01.08.2009 00, 00:00 hours.
Setting the date, time The date format can be switched from the display of day, month, year
and date format (jj.mm.aa) to the display of month, day, year (jj.mm.aa or jj.mm.aa).
ba75863e14 12/2011 31
Operation Multi 3410
Clock function
Date format: dd.mm.yy
Date: 30.09.2009
Time: 14:53:40
22.09.2009 08:00
32 ba75863e14 12/2011
Multi 3410 Operation
4.4.1 Système
Settings To open the Enregis. & config. menu, press the <MENU/ENTER > _
key in the measured value display. After completing the settings, switch
to the measured value display with <M>.
Default settings are printed in bold.
ba75863e14 12/2011 33
Operation Multi 3410
34 ba75863e14 12/2011
Multi 3410 Operation
4.4.2 Mémoire
This menu contains all functions to display, edit and erase stored mea-
sured values.
Note
Detailed information on the storage functions of the Multi 3410 is given
in section 4.10.
ba75863e14 12/2011 35
Operation Multi 3410
36 ba75863e14 12/2011
Multi 3410 Operation
SenTix 940
B092500013
Man. temperature: 25 °C
pH resolution 0.001
mV resolution 0.1
Buffer TEC
Calibration interval 7d
Unit for slope mV/pH
QSC:
30.09.2009 08:00
ba75863e14 12/2011 37
Operation Multi 3410
4.6 pH value
Note
The sensor connection and the USB-B (device) interface are galvani-
cally isolated. This enables interference-free measurements in
grounded measuring media.
Preparatory activities Perform the following preparatory activities when you want to measure:
38 ba75863e14 12/2011
Multi 3410 Operation
Stability control The stability control function (AutoRead) continually checks the stability
(AutoRead ) of the measurement signal. The stability has a considerable impact on
the reproducibility of measured values. The display of the measured
parameter flashes until a stable measured value is available.
You can start the Contrôle de stabilité manually at any time, irrespec-
tive of the setting for automatic Contrôle de stabilité (see section 4.4.3)
in the Système menu.
ba75863e14 12/2011 39
Operation Multi 3410
Note
You can prematurely terminate the Contrôle de stabilité function man-
ually with <MENU/ENTER> at any time. If the Contrôle de stabilité
function is prematurely terminated, the current measurement data are
output to the interface without the AutoRead info.
Criteria for a stable The Contrôle de stabilité function checks whether the measured values
measured value are stable within the monitored time interval.
40 ba75863e14 12/2011
Multi 3410 Operation
Settings The settings are made in the menu for calibration and measurement
settings of the pH/ORP measurement. To open the settings, display the
required parameter in the measured value display and press the
<MENU/ENTER> key. After completing the settings, switch to the mea-
sured value display with <M>.
Default settings are printed in bold.
ba75863e14 12/2011 41
Operation Multi 3410
42 ba75863e14 12/2011
Multi 3410 Operation
4.6.4 pH calibration
Why calibrate? During the operation of an IDS pH sensor, the zero point (asymmetry)
and
slope of the sensor change with time.As a result, an inexact measured
value is displayed. Calibration determines the current values of the
zero point and slope of the pH sensor and stores them in the measuring
instrument.
Thus, you should calibrate at regular intervals.
Buffer sets for You can use the buffer sets quoted in the table for an automatic calibra-
calibration tion. The pH values are valid for the specified temperature values. The
temperature dependence of the pH values is taken into consideration
during the calibration.
2 NIST/DIN 1,679 25 °C
DIN buffers according to DIN 19266 4,006
and NIST Traceable Buffers 6,865
9,180
12,454
3 TEC 2,000 25 °C
WTW Technical buffers 4,010
7,000
10,011
4 Merck 1* 4,000 20 °C
7,000
9,000
5 Merck 2 * 1,000 20 °C
6,000
8,000
13,000
6 Merck 3 * 4,660 20 °C
6,880
9,220
7 Merck 4 * 2,000 20 °C
4,000
7,000
10,000
ba75863e14 12/2011 43
Operation Multi 3410
8 Merck 5 * 4,010 25 °C
7,000
10,000
12 Fisher * 2,007 25 °C
4,002
7,004
10,002
13 Fluka BS * 4,006 25 °C
6,984
8,957
14 Radiometer * 1,678 25 °C
4,005
7,000
9,180
15 Baker * 4,006 25 °C
6,991
10,008
16 Metrohm * 3,996 25 °C
7,003
8,999
17 Beckman * 4,005 25 °C
7,005
10,013
19 Precisa * 3,996 25 °C
7,003
8,999
44 ba75863e14 12/2011
Multi 3410 Operation
21 Reagecon 20 * 2,000 20 °C
4,000
7,000
10,000
13,000
22 Reagecon 25 * 2,000 25 °C
4,000
7,000
10,000
13,000
23 Chemsolute * 2,000 20 °C
4,000
7,000
10,000
24 USABlueBook * 4,000 25 °C
7,000
10,000
Note
The buffers are selected in the menu, pH / <MENU/ENTER> / Calibra-
tion / Tampon (see section 4.6.3).
ba75863e14 12/2011 45
Operation Multi 3410
Calibration points Calibration can be performed using one to five buffer solutions in any
order (single-point to five-point calibration). The meter determines the
following values and calculates the calibration line as follows:
Note
You can display the slope in the units, mV/pH or % (see section 4.6.3).
Stability control The calibration procedure automatically activates the stability control
function. The current measurement with stability control can be termi-
nated at any time (accepting the current value).
Calibration record The new calibration values are displayed when a calibration procedure
is completed.
Display calibration data You can have the data of the last calibration displayed (see section
and output to interface 4.6.8). Subsequently, you can transmit the displayed calibration data to
the interface, e. g. to a PC, with the <PRT> key.
Note
The calibration record is automatically transmitted to the interface after
calibrating.
46 ba75863e14 12/2011
Multi 3410 Operation
Sample record
Multi 3410
Ser. no. 09250023
CALIBRATION pH
Calibration date 31.07.2009 16:13:33
SenTix 940
Ser. no. B092500013
TEC
Buffer 1 4.01
Buffer 2 7.00
Buffer 3 10.01
Voltage 1 184.0 mV 24.0 °C
Voltage 2 3.0 mV 24.0 °C
Voltage 3 -177.0 mV 24.0 °C
Slope -60.2 mV/pH
Asymmetry 4.0 mV
Sensor +++
etc...
Calibration evaluation After calibrating, the meter automatically evaluates the calibration. The
zero point and slope are evaluated separately. The worse evaluation of
both is taken into account. The evaluation appears on the display and
in the calibration record.
Note
For pH IDS sensors, you can optionally enable a more finely graded
calibration evaluation (QSC) (see section 4.6.10).
ba75863e14 12/2011 47
Operation Multi 3410
Preparatory activities Perform the following preparatory activities when you want to calibrate:
After the specified calibration interval has expired, the sensor symbol
or the QSC color scale flashes. It is still possible to measure.
Note
To ensure the high measuring accuracy of the measuring system, cal-
ibrate after the calibration interval has expired.
Setting the calibration The calibration interval is set to 7 days (d7) in the factory.
interval You can change the interval (1 ... 999 days):
48 ba75863e14 12/2011
Multi 3410 Operation
Make sure that in the sensor menu, Tampon menu, the buffer set is cor-
rectly selected (see section 4.6.3).
Use any one to five buffer solutions of the selected buffer set in ascend-
ing or descending order.
Note
If single-point calibration was set in the menu, the calibration procedure
is automatically finished with the measurement of buffer solution 1 and
the calibration record is displayed.
22.09.2009 08:00
ba75863e14 12/2011 49
Operation Multi 3410
22.09.2009 08:00
Note
For single-point calibration, the instrument uses the Nernst slope
(-59.2 mV/pH at 25 °C) and determines the zero point of the IDS pH
sensor.
50 ba75863e14 12/2011
Multi 3410 Operation
22.09.2009 08:00
ba75863e14 12/2011 51
Operation Multi 3410
22.09.2009 08:00
Note
Calibration is automatically completed after the last buffer of a buffer
set has been measured. Then the calibration record is displayed.
The calibration line is determined by linear regression.
52 ba75863e14 12/2011
Multi 3410 Operation
Make sure that in the sensor menu, Tampon menu, the ConCal buffer
set is correctly selected (see section 4.6.3).
Note
If single-point calibration was set in the menu, the calibration procedure
is automatically finished with the measurement of buffer solution 1 and
the calibration record is displayed.
22.09.2009 08:00
ba75863e14 12/2011 53
Operation Multi 3410
22.09.2009 08:00
22.09.2009 08:00
8 Set the nominal buffer value for the measured temperature with
<><>.
9 Accept the calibration value with <MENU/ENTER>.
The calibration display for the next buffer appears (voltage dis-
play).
10 If necessary, finish the calibration procedure as a single-point
calibration with <M>.
The calibration record is displayed.
Note
For single-point calibration, the instrument uses the Nernst slope
(-59.2 mV/pH at 25 °C) and determines the zero point of the IDS pH
sensor.
54 ba75863e14 12/2011
Multi 3410 Operation
22.09.2009 08:00
16 Set the nominal buffer value for the measured temperature with
<><>.
17 Accept the calibration value with <MENU/ENTER>.
The calibration display for the next buffer appears (voltage dis-
play).
18 If necessary, finish the calibration procedure as a two-point
calibration with <M>.
The calibration record is displayed.
ba75863e14 12/2011 55
Operation Multi 3410
22.09.2009 08:00
24 Set the nominal buffer value for the measured temperature with
<><>.
25 Accept the calibration value with <MENU/ENTER>.
The calibration display for the next buffer appears (voltage dis-
play).
26 If necessary, use <M> to finish the calibration.
The calibration record is displayed.
or
Continue calibrating using the next buffer with <MENU/
ENTER>.
Note
After the fifth buffer has been measured the calibration is automatically
finished. Then the calibration record is displayed.
The calibration line is determined by linear regression.
56 ba75863e14 12/2011
Multi 3410 Operation
The calibration data can be displayed and then output to the interface.
Displaying the The calibration record of the last calibration is to be found under the
calibration record menu item, Calibration / Protocole de calibration. To open it in the mea-
_
sured value display, press the <CAL > key.
ba75863e14 12/2011 57
Operation Multi 3410
1
2
3
4
The limits of the calibrated range are determined by the buffers used
for calibration:
58 ba75863e14 12/2011
Multi 3410 Operation
General information The QSC function (Quality Sensor Control) is a new sensor evaluation
on the QSC function for digital IDS sensors. It evaluates the condition of an IDS pH sensor
individually and with a very fine grading.
On the display, the QSC color scale (from green to yellow) indicates the
current sensor evaluation by means of a pointer.
The finely graded sensor evaluation of the QSC function promptly calls
your attention to changes of the sensor.
Thus you can do what is necessary to restore the optimum measuring
quality (e.g. clean, calibrate or replace the sensor).
Low tolerances for zero point Greater tolerances for zero point
and slope when using QSC buf- and slope when using commer-
fer solutions cial buffer sets
ba75863e14 12/2011 59
Operation Multi 3410
QSC calibration The QSC function is enabled by once carrying out an additional three-
point calibration with special QSC buffer solutions. It covers the mea-
suring range of the sensor from pH 2 to pH 11. The QSC initial calibra-
tion determines the actual condition of the sensor and stores it as a
reference in the sensor.
To meet the high requirements of a QSC initial calibration, the QSC ini-
tial calibration should optimally be carried out with the initial commis-
sioning of the sensor.
Carry out the normal calibrations for your special measuring range with
your usual standard solutions as previously done.
Note
As soon as the QSC function was enabled for an IDS sensor, it is not
possible to return to the sensor evaluation with the sensor symbol for
this sensor.
22.09.2009 08:00
Note
Carry out the QSC initial calibration very carefully. It determines the ref-
erence value for the sensor. This reference value cannot be overwritten
or reset.
As soon as the QSC function was enabled, it is not possible to return to
the sensor evaluation with the sensor symbol.
60 ba75863e14 12/2011
Multi 3410 Operation
You can carry out QSC control calibrations at greater intervals than
normal calibrations.
A QSC control calibration can, e.g. be useful if the sensor evaluation
noticeably changed (after some normal calibrations).
ba75863e14 12/2011 61
Operation Multi 3410
Note
The sensor connection and the USB-B (device) interface are galvani-
cally isolated. This enables interference-free measurements in
grounded measuring media.
Preparatory activities Perform the following preparatory activities when you want to measure:
Note
IDS ORP sensors are not calibrated. However, you can check IDS
ORP sensors using a test solution.
62 ba75863e14 12/2011
Multi 3410 Operation
Stability control The stability control function (AutoRead) continually checks the stability
(AutoRead ) of the measurement signal. The stability has a considerable impact on
the reproducibility of measured values. The display of the measured
parameter flashes until a stable measured value is available.
You can start the Contrôle de stabilité manually at any time, irrespec-
tive of the setting for automatic Contrôle de stabilité (see section 4.4.3)
in the Système menu.
Note
You can prematurely terminate the Contrôle de stabilité function man-
ually with <MENU/ENTER> at any time. If the Contrôle de stabilité
function is prematurely terminated, the current measurement data are
output to the interface without the AutoRead info.
Criteria for a stable The Contrôle de stabilité function checks whether the measured values
measured value are stable within the monitored time interval.
ba75863e14 12/2011 63
Operation Multi 3410
Settings The settings are made in the menu for measuring settings of the ORP
measurement. To open the settings, display the required parameter in
the measured value display and press the <MENU/ENTER> key. After
completing the settings, switch to the measured value display with
<M>.
Default settings are printed in bold.
64 ba75863e14 12/2011
Multi 3410 Operation
Note
The sensor connection and the USB-B (device) interface are galvani-
cally isolated. This enables interference-free measurements in
grounded measuring media.
Temperature IDS D.O. sensors measure the temperature with a temperature sensor
measurement integrated in the IDS sensor.
Preparatory activities Perform the following preparatory activities when you want to measure:
Note
The FDO® 925 needs to be calibrated in special cases only. Regular
FDO® Checks are sufficient.
ba75863e14 12/2011 65
Operation Multi 3410
4.8.2 Measuring
Selecting the You can switch between the following displays with <M>:
displayed D.O. concentration [mg/l]
measured parameter
D.O. saturation [%]
D.O. partial pressure [mbar].
Salinity correction When measuring the concentration of solutions with a salt content of
more than 1 g/l, a salinity correction is required. For this, you have to
measure and input the salinity of the measured medium first.
When the salinity correction is switched on, the [SAL] indicator is dis-
played in the measuring window.
Note
You can switch the salinity correction on or off and enter the salinity in
the menu for calibration and measurement settings (see section 4.9.4).
Freezing the measured With the HOLD function, you can freeze the current measured value.
value (HOLD function) The displayed measured value stops changing until you switch the
HOLD function off.
Note
If the HOLD function is active, you can, e.g. start a manual measure-
ment with stability control.
66 ba75863e14 12/2011
Multi 3410 Operation
Stability control The stability control function (AutoRead) continually checks the stability
(AutoRead ) of the measurement signal. The stability has a considerable impact on
the reproducibility of measured values. The display of the measured
parameter flashes until a stable measured value is available.
You can start a measurement with Contrôle de stabilité manually at any
time, irrespective of the setting for automatic Contrôle de stabilité (see
section 4.4.3) in the Système menu.
Note
You can prematurely terminate the Contrôle de stabilité function man-
ually with <MENU/ENTER> at any time. If the Contrôle de stabilité
function is prematurely terminated, the current measurement data are
not output to the interface.
ba75863e14 12/2011 67
Operation Multi 3410
Criteria for a stable The Contrôle de stabilité function checks whether the measured values
measured value are stable within the monitored time interval.
68 ba75863e14 12/2011
Multi 3410 Operation
Settings The settings are available in the menu for measurement and calibration
settings. To open the settings, display the required parameter in the
measured value display and press the <MENU/ENTER> key. After
completing the settings, switch to the measured value display with
<M>.
ba75863e14 12/2011 69
Operation Multi 3410
70 ba75863e14 12/2011
Multi 3410 Operation
Why should you check With the FDO® Check procedure, you can find out in a simple manner
the sensor? whether the FDO® 925 D.O. sensor should be cleaned or calibrated.
When should you check Checking can be useful in the following cases:
the sensor? When the check interval has expired
If the measured values seem to be implausible
If you assume that the sensor cap is contaminated or at the end of
its lifetime
After the sensor cap was exchanged
Routinely within the scope of company quality assurance measures.
Stability control The Stability control function (AutoRead) is automatically activated for
(AutoRead) the FDO® Check.
Carrying out the FDO® Proceed as follows to carry out the FDO® Check procedure:
Check procedure
1 Connect the D.O. sensor to the meter.
2 Place the D.O. sensor in the check and storage vessel, FDO®
Check.
Note
The sponge in the check and storage vessel must be moist (not wet).
Leave the sensor in the check and storage vessel long enough so it can
adapt to the ambient temperature.
ba75863e14 12/2011 71
Operation Multi 3410
22.03.2010 08:00
Evaluation The evaluation is based on the accuracy required by the user. Together
with the nominal value (100 %), this results in a validity scope for the
check.
If the measured value is outside the validity scope, the sensor shaft and
membrane should be cleaned, and the check should then be repeated
(see section 5.4.1).
Example:
– Required accuracy: ± 2 %.
– In water vapor-saturated air or air-saturated water, the nominal
value for the relative D.O. saturation (abbreviated: saturation) is
100 %.
– Therefore, the validity scope is 98 ... 102 %
– The check resulted in a measured value of 99,3 %
The measurement error is within the specified validity scope.
No cleaning or user calibration is required.
72 ba75863e14 12/2011
Multi 3410 Operation
Why calibrate? D.O. sensors age. This changes the slope of the D.O. sensor. Calibra-
tion determines the current slope of the sensor and stores this value in
the instrument.
Note
The FDO® 925 D.O. sensor ages so little it does not have to be regu-
larly calibrated.
To detect changes of the sensor as early as possible, the FDO® Check
procedure can be useful (see section 4.8.4).
When to calibrate? If your evaluation of the FDO® Check procedure suggests a calibra-
tion
When the calibration interval has expired
If your accuracy requirements are especially high
Routinely within the scope of company quality assurance measures.
Display calibration data You can have the data of the last calibration displayed (see section
and output to interface 4.9.6). Subsequently, you can transmit the displayed calibration data to
the interface, e. g. to a PC, with the <PRT> key.
Note
The calibration record is automatically transmitted to the interface after
calibrating.
Sample record
Multi 3410
Ser. no. 10139695
CALIBRATION Ox
Calibration date 30.03.2010 16:13:33
FDO 925
Ser. no. 10146858
Calibration evaluation After the calibration, the meter automatically evaluates the current sta-
tus of the calibration. The evaluation appears on the display and in the
calibration record.
ba75863e14 12/2011 73
Operation Multi 3410
S < 0.90 or
Error Error
S > 1.10
Eliminate the error according to
chapter 6 WHAT TO DO IF...
Note
The sponge in the check and storage vessel must be moist (not wet).
Leave the sensor in the check and storage vessel long enough so it can
adapt to the ambient temperature.
74 ba75863e14 12/2011
Multi 3410 Operation
22.03.2010 08:00
ba75863e14 12/2011 75
Operation Multi 3410
The calibration data can be displayed and then output to the interface.
Displaying the The calibration record of the last calibration is available under the menu
calibration record item, Calibration / Protocole de calibration. To open it in the measured
_
value display, press the <CAL > key.
76 ba75863e14 12/2011
Multi 3410 Operation
4.9 Conductivity
Note
The sensor connection and the USB-B (device) interface are galvani-
cally isolated. This enables interference-free measurements in
grounded measuring media.
Temperature IDS sensors measure the temperature with a temperature sensor inte-
measurement grated in the IDS sensor.
Preparatory activities Perform the following preparatory activities when you want to measure:
4.9.2 Measuring
ba75863e14 12/2011 77
Operation Multi 3410
Selecting the You can switch between the following displays with <M>:
displayed Conductivity [μS/cm] / [mS/cm]
measured parameter
Resistivity [Ω·cm] / [kΩ·cm] / [MΩ·cm]
Salinity SaL [ ]
Total dissolved solids TDS [mg/l] / [g/l]
The factor to calculate the total dissolved solids is set to 1.00 in the fac-
tory. You can adjust this factor to meet your requirements in the range
of 0.40 to 1.00. The factor is set in the menu for the parameter, TDS.
Freezing the measured With the HOLD function, you can freeze the current measured value.
value (HOLD function) The displayed measured value stops changing until you switch the
HOLD function off.
Note
If the HOLD function is active, you can, e.g. start a manual measure-
ment with stability control.
Stability control The stability control function (AutoRead) continually checks the stability
(AutoRead ) of the measurement signal. The stability has a considerable impact on
the reproducibility of measured values. The display of the measured
parameter flashes until a stable measured value is available.
You can start the Contrôle de stabilité function manually at any time,
irrespective of the setting for automatic Contrôle de stabilité (see sec-
tion 4.4.3) in the Système menu.
78 ba75863e14 12/2011
Multi 3410 Operation
Note
You can prematurely terminate the Contrôle de stabilité function man-
ually with <MENU/ENTER> at any time. If the Contrôle de stabilité
function is prematurely terminated, the current measurement data are
output to the interface without the AutoRead info.
Criteria for a stable The Contrôle de stabilité function checks whether the measured values
measured value are stable within the monitored time interval.
ba75863e14 12/2011 79
Operation Multi 3410
Note
The reference temperature and temperature compensation are set in
the menu for the parameter, conductivity (see section 4.9.4).
Application tips Select the following temperature compensations given in the table
according to the respective test sample:
80 ba75863e14 12/2011
Multi 3410 Operation
Overview The following settings are possible for IDS conductivity sensors:
Protocole de calibration (display)
Mémoire calibration (display)
Intervalle cal.
Reference temperature
Temperature compensation
TDS factor
Unit of the temperature
Settings The settings are made in the menu for the measured parameter, con-
ductivity. To open the settings, display the required parameter in the
measured value display and press the <MENU/ENTER> key. After
completing the settings, switch to the measured value display with
<M>.
The possible settings are individually displayed for each sensor. Below
the setting menu is displayed for two IDS sensors (TetraCon 925,
LR325/01).
Default settings are printed in bold.
ba75863e14 12/2011 81
Operation Multi 3410
82 ba75863e14 12/2011
Multi 3410 Operation
ba75863e14 12/2011 83
Operation Multi 3410
Why determine the cell Aging slightly changes the cell constant, e. g. due to coatings. As a
constant? result, an inexact measured value is displayed. The original character-
istics of the cell can often be restored by cleaning the cell. Calibration
determines the current value of the cell constant and stores this value
in the meter. Thus, you should calibrate at regular intervals (we recom-
mend: every 6 months).
Procedure You can determine the actual cell constant of the IDS conductivity sen-
sor cell by calibrating with the control standard in the following range:
0.450 ... 0.500 cm-1
(e.g. TetraCon 925, nominal cell constant 0.475)
The cell constant is determined in the control standard, 0.01 mol/l KCl.
In the delivery condition, the calibrated cell constant of the IDS sensor
is set to 0.475 cm-1 (conductivity measuring cell, TetraCon 925).
Display calibration data You can have the data of the last calibration displayed (see section
and output to interface 4.9.6). Subsequently, you can transmit the displayed calibration data to
the interface, e. g. to a PC, with the <PRT> key.
Note
The calibration record is automatically transmitted to the interface after
calibrating.
Sample record
Multi 3410
Ser. no. 09250023
CALIBRATION Cond
Calibration date 31.07.2009 16:13:33
TetraCon 925
Ser. no. 09250033
Calibration evaluation After calibration, the meter automatically evaluates the current status of
the calibration. The evaluation appears on the display and in the cali-
bration record.
84 ba75863e14 12/2011
Multi 3410 Operation
Determining the cell For this calibration procedure, the Type setting must be set to cal . Pro-
constant ceed as follows to determine the cell constant:
22.09.2009 08:00
ba75863e14 12/2011 85
Operation Multi 3410
The calibration data can be displayed and then output to the interface.
Displaying the The calibration record of the last calibration is to be found under the
calibration record menu item, Calibration / Protocole de calibration. To open it in the mea-
_
sured value display, press the <CAL > key.
86 ba75863e14 12/2011
Multi 3410 Operation
Storage locations The Multi 3410 meter has two measurement data memories. The mea-
sured values recorded either manually or automatic are stored sepa-
rately in individual measurement data memories.
ba75863e14 12/2011 87
Operation Multi 3410
ID number: 1
Continue
22.09.2009 08:00
If the storage is full When all storage locations are occupied, it is not possible to continue
storing. Then you can e.g. transmit the stored data to a PC or a USB
flash drive (see section 4.10.3) and subsequently erase the storage
(see section 4.10.4).
Configuring the
automatic storage
1 Press the <STO > key. _
The menu for automatic storage appears.
function
88 ba75863e14 12/2011
Multi 3410 Operation
22.09.2009 08:00
Graphical display of the
storage usage
Settings You can configure the automatic storage function with the following set-
tings:
Starting the automatic To start the automatic storage function, select continuer with <><>
storage function and confirm with <MENU/ENTER>. The meter switches to the mea-
sured value display.
ba75863e14 12/2011 89
Operation Multi 3410
30.09.2009 08:00
Note
If the automatic storage function is activated, only the following keys
_
are active: <M>, <STO > and <On/Off>. The other keys and the
automatic switch-off function are deactivated.
Terminating the Proceed as follows to switch off the automatic storage function before
automatic storage the adjusted storage duration has expired:
function prematurely
1 Press the <STO > key._
The following window appears.
Warning
Yes
No
22.09.2009 08:00
90 ba75863e14 12/2011
Multi 3410 Operation
Editing the data storage The storage is edited in the menu, Enregis. & config. / Mémoire. To
_
open the Enregis. & config. menu, press the <MENU/ENTER > key
in the measured value display.
Note
The settings are explained here using the manual storage as an exam-
ple. The same settings and functions are available for the automatic
storage.
ba75863e14 12/2011 91
Operation Multi 3410
22.09.2009 08:00
Sample printout
31.07.2009 09:56:20
Multi 3410
Ser. no. 09250023
SenTix 940
Ser. no. B092500013
ID number 2
pH 6.012 24.8 °C, AR, Sensor: +++
________________________________________
31.07.2009 10:56:20
Multi 3410
Ser. no. 09250013
SenTix 940
Ser. no. B092500013
ID number 2
pH 6.012 24.8 °C, AR, Sensor: +++
________________________________________
etc...
Quitting the display To quit the display of stored measurement datasets, you have the fol-
lowing options:
Switch directly to the measured value display with <M>.
Quit the display and move to the next higher menu level with
<ESC>.
92 ba75863e14 12/2011
Multi 3410 Operation
Via the USB-B interface (USB Device) you can transmit data to a PC or
printer and update the meter software.
Installation of the USB System requirements of the PC for installation of the USB driver:
driver on the PC
PC with at least one free USB connection and CD-ROM drive
Windows 2000, Windows XP, Windows Vista or Windows 7.
ba75863e14 12/2011 93
Operation Multi 3410
Connect the USB-A interface (USB Host) of the Multi 3410 to a USB
flash drive.
Note
For suitabele USB printers: Please contact the service.
Via the USB-B interface you can transmit data to a PC. The following
table shows which data are transmitted to the interface in which way:
94 ba75863e14 12/2011
Multi 3410 Operation
Note
The following rule applies: With the exception of the menus, shortly
pressing the <PRT> key generally outputs the display contents to the
interface (displayed measured values, measuring datasets, calibration
records). If there is a USB-B connection (such as to a PC) at the same
time, the data are output only to the USB-B interface.
Via the USB-A interface you can transmit data to a USB memory
device. The following table shows which data are transmitted to the
interface in which way:
ba75863e14 12/2011 95
Operation Multi 3410
4.12 Reset
You can reset (initialize) all sensor settings and sensor-independent
settings separately from each other.
Note
The calibration data are reset to the default settings together with the
measuring parameters. Recalibrate after performing a reset.
The sensor settings are reset under the Remise à zéro menu item in
the menu for calibration and measurement settings. To open the set-
tings, display the required parameter in the measured value display
and press the <MENU/ENTER> key.
ORP The following settings for ORP measurements are reset to the default
settings with the Remise à zéro function:
The sensor settings are reset under the Remise à zéro menu item in
the menu for calibration and measurement settings. To open the set-
96 ba75863e14 12/2011
Multi 3410 Operation
Dissolved oxygen The following settings for D.O. measurements are reset to the default
settings with the Remise à zéro function:
The sensor settings are reset under the Remise à zéro menu item in
the menu for calibration and measurement settings. To open the set-
tings, display the required parameter in the measured value display
and press the <MENU/ENTER> key.
Conductivity The following settings for conductivity measurements are reset to the
default settings with the Remise à zéro function:
The sensor settings are reset under the Remise à zéro menu item in
the menu for calibration and measurement settings. To open the set-
tings, display the required parameter in the measured value display
and press the <MENU/ENTER> key.
ba75863e14 12/2011 97
Operation Multi 3410
The system settings are reset in the menu, Enregis. & config. / Système
/ Remise à zéro. To open the Enregis. & config. menu, press the
_
<MENU/ENTER > key in the measured value display.
98 ba75863e14 12/2011
Multi 3410 Maintenance, cleaning, disposal
Note
See the relevant operating manuals of the IDS sensors for instructions
on maintenance.
CAUTION
Make sure that the poles of the rechargeable batteries are posi-
tioned correctly.
The ± signs on the batteries must correspond to the ± signs in the
battery compartment.
ba75863e14 12/2011 99
Maintenance, cleaning, disposal Multi 3410
5 Close the battery compartment (2) and tighten the screws (1).
5.2 Cleaning
Occasionally wipe the outside of the measuring instrument with a
damp, lint-free cloth. Disinfect the housing with isopropanol as
required.
CAUTION
The housing is made of synthetic material (ABS). Thus, avoid con-
tact with acetone or similar detergents that contain solvents. Re-
move any splashes immediately.
5.3 Packing
This meter is sent out in a protective transport packing.
We recommend: Keep the packing material. The original packing pro-
tects the meter against damage during transport.
5.4 Disposal
Note
This meter contains rechargeable batteries. Batteries that have been
removed must only be disposed of at a recycling facility set up for this
purpose or via the retail outlet.
It is illegal to dispose of the batteries in household refuse.
6 What to do if...
6.1 General information
Cause Remedy
– Batteries almost empty – Charge the batteries (see
section 3.3.2 CONNECTING
THE POWER PACK / CHARGING
Display THE BATTERIES)
– Replace the batteries (see
section 5.1 MAINTENANCE)
Data transmission to
Cause Remedy
USB memory device
does not work – Connected USB memory device – Use other USB memory
has not been recognized, e. g. device
– the USB memory device has – Reformat the USB memory
been formattet to a file sys- device to FAT 16 or FAT 32
tem which is not supported file system
(e. g. NTFS) (Caution: Reformatting
erases all data on the USB
memory device. Back up all
data before reformatting.)
Error message,
Cause Remedy
Only use rechargeable
batteries! – A voltage that is unusual for – Disconnect the power pack
Ni-MH 1.2 V, >2100 mAh NiMH rechargeable batteries from the meter.
was found. – Check whether there are
suitable rechargeable bat-
teries (Ni-MH 1.2 V, >2100
mAh) in the battery compart-
ment.
– Unsuitable batteries:
Insert suitable recharge-
able batteries and recon-
nect the power pack.
– Suitable batteries:
Connect the power pack
and close the error mes-
sage with <[ESC]> or
<M>.
6.2 pH
Error message,
OFL, UFL Cause Remedy
IDS pH sensor:
– Measured value outside the – Use suitable IDS pH sensor
measuring range
– Air bubble in front of the junction – Remove air bubble
– Air in the junction – Extract air or moisten junc-
tion
– Cable broken – Exchange IDS pH sensor
– Gel electrolyte dried out – Exchange IDS pH sensor
Test sample:
– pH value not stable – Measure with air excluded if
necessary
– Temperature not stable – Adjust temperature if neces-
sary
Note
More information, as well as notes on cleaning and replacement of
sensors, are given in the documentation of your sensor.
6.4 Conductivity
Error message,
OFL Cause Remedy
– Measured value outside the – Use suitable IDS conductiv-
measuring range ity sensor
Note
More information, as well as notes on cleaning and replacement of
sensors, are given in the documentation of your sensor.
7 Technical data
7.1 General data
#
The operational life is shorter if, e.g.
- the maximum display illumination is set
Note
Further data are given in the documentation of your sensor.
8 Lists
This chapter provides additional information and orientation aids.
Specialist terms The glossary briefly explains the meaning of the specialist terms. How-
ever, terms that should already be familiar to the target group are not
described here.
Index The index will help you to find the topics that you are looking for.
Glossary
Adjusting To manipulate a measuring system so that the relevant value (e. g. the
displayed value) differs as little as possible from the correct value or
a value that is regarded as correct, or that the difference remains with-
in the tolerance.
Asymmetry see zero point
AutoRange Name of the automatic selection of the measuring range.
Calibration Comparing the value from a measuring system (e. g. the displayed
value) to the correct value or a value that is regarded as correct. Of-
ten, this expression is also used when the measuring system is adjust-
ed at the same time (see adjusting).
D.O. partial pressure Pressure caused by the oxygen in a gas mixture or liquid.
Electromotive force of The electromotive force U of the combination electrode is the measur-
an electrode able electromotive force of an electrode in a solution. It equals the
sum of all the galvanic voltages of the combination electrode. Its de-
pendency on the pH results in the electrode function, which is charac-
terized by the parameters, slope and zero point.
Junction The junction is a porous body in the housing wall of reference elec-
trodes or electrolyte bridges. It arranges the electrical contact be-
tween two solutions and makes the electrolyte exchange more
difficult. The expression, junction, is also used for ground or junction-
less transitions.
Measured parameter The measured parameter is the physical dimension determined by
measuring, e. g. pH, conductivity or D.O. concentration.
Measured value The measured value is the special value of a measured parameter to
be determined. It is given as a combination of the numerical value and
unit (e. g. 3 m; 0.5 s; 5.2 A; 373.15 K).
B K
Battery compartment . . . . . . . . . . . . . . 21, 95 Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
C M
Calibration Measured value display . . . . . . . . . . . . . . . 27
Conductivity . . . . . . . . . . . . . . . . . . . . . 79 Measurement accuracy . . . . . . . . . . . . . . . 47
O2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Measurement data storage
pH . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Edit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Calibration evaluation Erase . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Conductivity . . . . . . . . . . . . . . . . . . . . . 79 Storage locations . . . . . . . . . . . . . . . . . 82
O2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Measurement dataset . . . . . . . . . . . . . . . . 82
pH . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Measuring
Calibration interval Conductivity . . . . . . . . . . . . . . . . . . . . . 72
Conductivity . . . . . . . . . . . . . . . . . . . . . 76 O2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
O2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 ORP voltage . . . . . . . . . . . . . . . . . . . . 60
pH . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 pH . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Calibration points Menu for calibration and measurement settings
pH . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Conductivity . . . . . . . . . . . . . . . . . . . . . 76
Calibration records O2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Conductivity . . . . . . . . . . . . . . . . . . . . . 81 pH/ORP . . . . . . . . . . . . . . . . . . . . . 40, 62
O2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Menus (navigation) . . . . . . . . . . . . . . . . . . 27
pH . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Messages . . . . . . . . . . . . . . . . . . . . . . . . . 28
Cell constant . . . . . . . . . . . . . . . . . . . . . . . 79
Connect the power pack . . . . . . . . . . . . . . 22 O
Connecting a PC . . . . . . . . . . . . . . . . . 88, 90 Operational safety . . . . . . . . . . . . . . . . . . . 18
D P
Dataset . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 pH buffer sets . . . . . . . . . . . . . . . . . . . . . . 42
Date and time . . . . . . . . . . . . . . . . . . . . . . . 31 Precautions . . . . . . . . . . . . . . . . . . . . . . . . 17
Default settings
Measured parameter . . . . . . . . . . . . . . 91 R
System settings . . . . . . . . . . . . . . . . . . 94 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 RS232 interface . . . . . . . . . . . . . . . . . . . . . 90
E S
Energy saving feature . . . . . . . . . . . . . . . . 23 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Scope of delivery . . . . . . . . . . . . . . . . . . . . 21
Setting the date . . . . . . . . . . . . . . . . . . . . . 23
Setting the time . . . . . . . . . . . . . . . . . . . . . 23
Single-point calibration
pH . . . . . . . . . . . . . . . . . . . . . . 49, 52, 53
Slope
pH . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Slope, relative . . . . . . . . . . . . . . . . . . . . . . 68
Socket field . . . . . . . . . . . . . . . . . . . . . . . . 13
Stability control
automatic . . . . . . . . . . . . . . . . . . . . . . . 35
Conductivity . . . . . . . . . . . . . . . . . . . . . 73
O2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
ORP . . . . . . . . . . . . . . . . . . . . . . . . . . 61
pH . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Storage interval . . . . . . . . . . . . . . . . . . . . . 83
Storing in memory . . . . . . . . . . . . . . . . . . . 63
Automatic . . . . . . . . . . . . . . . . . . . . . . 83
Manual . . . . . . . . . . . . . . . . . . . . . . . . 83
T
Temperature compensation . . . . . . . . . . . 75
Temperature measurement
Conductivity . . . . . . . . . . . . . . . . . . . . . 71
O2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
pH . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Three-point calibration
pH . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Transmitting data . . . . . . . . . . . . . . . . . . . 88
Transmitting measured values . . . . . . . . . 88
Two-point calibration
pH . . . . . . . . . . . . . . . . . . . . . . 49, 52, 54
Z
Zero point of pH combination electrode . . 42
For the update via the USB-B interface, the following is required:
a free USB interface (virtual COM port) on the PC
the driver for the USB interface (on the enclosed CD-ROM)
the USB cable (included in the scope of delivery of the Multi 3410).
Program installation
1 Install the downloaded firmware update on a PC.
An update folder is created in the Windows start menu.
If an update folder already exists for the meter (or meter type),
the new data are displayed there.
Program start
2 In the windows start menu, open the update folder and start the
firmware update program for the meter
Firmware update
3 Using the USB interface cable, connect the Multi 3410 to a
USB interface (virtual COM port) of the PC.
4 Switch on the Multi 3410.
5 In the firmware update program, start the update process with
OK.
6 Follow the instructions of the firmware update program.
During the programming process, a corresponding message
and a progress bar (in %) are displayed.
The programming process takes up to 15 minutes. A termina-
tory message is displayed after a successful programming pro-
cess. The firmware update is completed.
7 Disconnect the Multi 3410 from the PC.
The Multi 3410 is ready for operation again.
After switching the meter off and on you can check whether the meter
has taken over the new software version (see page 101).
For the update via the USB-B interface, the following is required:
a free USB interface (virtual COM port) on the PC
the driver for the USB interface (on the enclosed CD-ROM)
the USB cable (included in the scope of delivery of the Multi 3410).
Program installation
1 Install the downloaded firmware update on a PC.
An update folder is created in the Windows start menu.
If an update folder already exists for the sensor (or sensor
type), the new data are displayed there.
Program start
2 In the windows start menu, open the update folder and start the
firmware update program for the IDS sensor
Firmware update
3 Connect the IDS sensor to the Multi 3410 meter.
4 Using the USB interface cable, connect the Multi 3410 to a
USB interface (virtual COM port) of the PC.
5 Switch on the Multi 3410.
6 In the firmware update program, start the update process with
OK.
7 Follow the instructions of the firmware update program.
During the programming process, a corresponding message
and a progress bar (in %) are displayed.
The programming process takes up to 5 minutes. A terminatory
message is displayed after a successful programming process.
The firmware update is completed.
8 Disconnect the Multi 3410 from the PC.
Meter and sensor are ready for operation again.
After switching the meter off and on you can check whether the sensor
has taken over the new software version (see page 101).
Dr.-Karl-Slevogt-Straße 1
D-82362 Weilheim
Germany