Hydrone Platform page $500
‘SYSTEM GENERAL Materials and Components
5a|SONSUB ost
4129052-SA-2R00-DB-00001 ra. AO
Hydrane
6.2.3. DS-03A rev.00 - type 630 age-hardening stainless steel! - structural
use
2a)_[ Ter oF marten: Type 630 Age-hardering Stainless Stel
22)_[ UNeD NuweennG vere | 517600
23)_[ comenciat name(s aH
2a)_| seeane mniwomve | IMP 7
say] STENTS, er ce
2a) | score: This OS species te seecedopins in he refered stancard ard maa ed
quirements which shall spersde the crresponcing equreretsia he
2a) UMITATIONS ‘The requrerents ofthis Data Shoot re applable to produ within the Tek
range 3mm t9 50mm
tal_| Forsnas asa7os | 630
bay [ Paes rstwaees |
a)_| Basene shapes asmnsee | 60
Tel) MANUFACTURING PROCESS. | Ourng heat reatment components salle placed m auch way ao ensure Free
relation around each component ding the heat testent oes neue
possible quenching operation.
2)_| HEATTREATMENTTDEIVERY — | Sokaion treatment eondkion Al + coubl preiptaton Fardeing heat reat
‘conDITion: (conditon #13500}, 25 olows:
+ solution annealing at 1080 25 «Cand ar coo ng or evi quencing to
+ Seat preitaon hardening syle a 620 15 Cor 4 minirum st
{empeatre ther a colin or gud quenching to below 32°C,
+ second recptation-hardening cyl t 620 = 15 Cfr 49 minimum at
temperature the ai coling Hau quenching to below 32°C.
a)_| EREMTERLCOMPOSTTON, —_| Aa per apolable AST andar
a) TENSILE PROPERTIES The tense properties a ished products stall meet the requirement of Table
6.701 wis spectcaton
5) IMPACTREGUIREWENTS: | The Charpy noth impact properties fies produce shal met the
requirement of Tabla 5 ofthe Speciation
Testing shall be doe 20°C,
6) HawONESS REQUIREMENTS: | As per applcable ASTM standard, or max. 33 HRC (or 325 FVD), whichever the
lower
eo) | TesTsmerine ‘Samples or production testing shal realsbeay rele the properties inthe actual
a) | nowoestaucrveTesTInG | As perappcable ASTI standard. The allowing sede requirement all apr
(NomHydrone Platform age 560840
‘SYSTEM GENERAL Materials and Components
=| | SONSUB_ == shects Hudrone
139952-SA-9R00-DB-0000' rev. AD
~"a forgings above NPS2 shal be subjected to ulvasonie este)
averng teenie volume Ulrxerie inspection of forgings sal be nade
in aeordance with ASTRA ASEA, Acceptance rte salle 320710
= a acess surfaces oF forigs above NPS2 stall be subject to magnedie
parte speton accondarce wih ASTM AZTS Acceptance ertera,
‘rae accorsing to Supplementary Requirement S282 ASTM A788,
+ pistes ane other at prods:
PM raanic oration shal be performed in aeeordance with ASTM AS7E
Level wher 2125 mm.
+ bare and sections:
tamination m accordance wh ASM A745 to qalty levels QL/Q
Simenson shall subjeces te utrasonexaminaton macorcance with
ND" operators sha be cette in accordance wth EN 473 or equivalent,
20) | EXTENT OF RETESTING = case mater wil be provided with hisgedtionCerieate of ype 8.135 dened
stunt salle pe aplable ASTM standard, ach test unt shall be sujet to
ea) | REPAROF DEFECTS: Weld epa of base materiale nat acapiable
2) | SURFACE FNS White picked
a3) | wana he eompanent alba arted to nau ful raceebiiy to heat and heat
eeatment teach
a) SURFACE PROTECTION: Neve
a5) | CeRTACATION he material manufactarer shall have a quay sytem cried in accordance with
'sO900: andthe sytem shal have undergone aspeatcasensment fore
Materia shal be proved wit Inspection Cera of ype 32, 5a minimum, as
defined in EW 16208-2008 The mater cerieste stall ircuge te folowing
1+ hea ueatmentcondens eye and temperatures habe sate,
Full aceality shal be provides between the marking onthe materi and the
incase mater wl be provided wth nsaecion Cera f type as dete
Under wlnesing of SAPEN"'s epresentatve,o SAIPEM's ppcited specter
cerateation agency.Hydrone Platform page 57 9F 0
‘SYSTEM GENERAL -Materats and Components
5a|SONSUB Pst Hydrone
+133952-5A-3RO0-DB-00001 rev. AOS
CS a erry
Feared Pre reg Ee Dal renal ee ee
cS) Dy od
twin | two | Ev) uw
| nso] as] a 6 0 2 % a
weiee
tongstionn 0 om or 4,
1267