Professional Documents
Culture Documents
7.0 Bushing Shrink Fit Method
7.0 Bushing Shrink Fit Method
3.5.1 The tolerances for NAS 537, NAS 538, SAE-AS14237, and SAE-AS14238
standard bushings are shown in Table I and Figure 1. Install by shrink fit method unless
specified otherwise by engineering drawing.
3.5.2 Tolerances for interference critical bushings are shown in Table II. Install by
shrink fit method unless specified otherwise by engineering drawing
3.5.3 Tolerances for standard light press fit bushings with inside diameters finished to
size (NAS75, NAS76, NAS77) are listed in Table III.
3.5.4 Tolerances for standard clamp-up type bushings are listed in Table IV.
NAS 537
NAS 538 Bushing Outside Lug or Clevis Interference Fit
Dash Diameter=D1 Bore Diameter=D D1 - D
Number
Max Min Max Min Max Min
(inches) (inches) (inches) (inches) (inches) (inches)
4 0.3761 0.3756 0.3754 0.3748 0.0013 0.0002
5 0.4386 0.4381 0.4379 0.4373 0.0013 0.0002
6 0.5013 0.5006 0.5003 0.4997 0.0016 0.0003
7 0.5638 0.5631 0.5628 0.5622 0.0016 0.0003
8 0.6265 0.6257 0.6254 0.6247 0.0018 0.0003
9 0.6892 0.6882 0.6879 0.6872 0.0020 0.0003
10 0.8142 0.8132 0.8128 0.8120 0.0022 0.0004
11 0.8767 0.8757 0.8753 0.8745 0.0022 0.0004
12 0.9393 0.9383 0.9379 0.9370 0.0023 0.0004
14 1.0648 1.0638 1.0634 1.0625 0.0023 0.0004
16 1.1898 1.1888 1.1883 1.1873 0.0025 0.0005
18 1.3148 1.3138 1.3132 1.3122 0.0026 0.0006
AS14237
AS14238 Bushing Outside Lug or Clevis Interference Fit
Dash Diameter=D1 Bore Diameter=D D1 - D
Number
Max Min Max Min Max Min
(inches) (inches) (inches) (inches) (inches) (inches)
4 0.3767 0.3762 0.3758 0.3750 0.0017 0.0004
5 0.4393 0.4388 0.4383 0.4375 0.0018 0.0005
6 0.5020 0.5013 0.5008 0.5000 0.0020 0.0005
7 0.5646 0.5639 0.5634 0.5625 0.0021 0.0005
8 0.6272 0.6264 0.6259 0.6250 0.0022 0.0005
10 0.8150 0.8140 0.8134 0.8125 0.0025 0.0006
12 0.9400 0.9390 0.9384 0.9375 0.0025 0.0006
14 1.0651 1.0641 1.0635 1.0625 0.0026 0.0006
16 1.1901 1.1891 1.1885 1.1875 0.0026 0.0006
18 1.3151 1.3141 1.3135 1.3125 0.0026 0.0006
Table II Tolerances For EAC Interference Critical Bushings In Single–Pin Joints
EAC
Flanged
Bushing Bushing Outside Lug or Clevis Interference Fit
Dash Diameter=D1 Bore Diameter=D D1 - D
Number
Max Min Max Min Max Min
(inches) (inches) (inches) (inches) (inches) (inches)
4 0.3764 0.3759 0.3756 0.3750 0.0014 0.0003
5 0.4389 0.4384 0.4381 0.4375 0.0014 0.0003
6 0.5015 0.5010 0.5006 0.5000 0.0015 0.0004
7 0.5641 0.5636 0.5631 0.5625 0.0016 0.0005
8 0.6266 0.6261 0.6256 0.6250 0.0016 0.0005
9 0.6893 0.6888 0.6882 0.6875 0.0018 0.0006
10 0.7519 0.7514 0.7507 0.7500 0.0019 0.0007
11 0.8144 0.8139 0.8132 0.8125 0.0019 0.0007
12 0.8770 0.8765 0.8757 0.8750 0.0020 0.0008
13 0.9396 0.9391 0.9382 0.9375 0.0021 0.0009
14 1.0022 1.0017 1.0007 1.0000 0.0022 0.0010
15 1.1274 1.1268 1.1257 1.1250 0.0024 0.0011
16 1.1900 1.1894 1.1882 1.1875 0.0025 0.0012
17 1.2527 1.2521 1.2508 1.2500 0.0027 0.0013
18 1.3153 1.3147 1.3133 1.3125 0.0028 0.0014