Submersible Extra High Head Pump

www.tsurumi-global.com

Max. 230m head and excellent durability,

optimum for high head applications.

extra high head pump is equipped with duplex impellers that

deliver a maximum head of over 200m.
The upper impeller is attached in the reverse direction of the
lower impeller (back-to-back), and reduces thrust load and
enhances the durability of bearings. High-chromium cast iron is
used for the impellers and mouth ring, to ensure wear
resistance. The labyrinth ring and shaft sleeve are made of 630
stainless steel that is superior in wear resistance and strength to
other stainless steels, to provide a perfect countermeasure
against wear caused by high pressure generated in the casing.
Additionally, the pump is equipped with seal pressure relief ports
that release pump pressure applied to the mechanical seal. The
flow-thru discharge design of the pump forcibly cools the motor
so as to endure even extended operation at low water level.

Amenities from Technology

for People and the Earth
 1

1 Anti-wicking Cable Entry 2 Miniature Thermal Protector

Prevents water incursion due to capillary wicking React to excessive heat caused by dry-running. The
should the power cable be damaged or the end bimetal strip opens to cause the control panel to shut
submerged. the power supply. 2

3 Dual Inside Mechanical Seal 4 Oil Lifter (Patened)

Eliminates problems like spring failure and ensures a Provides lubrication and cooling of the seal faces
long service life. Isolated in the oil chamber where a down to 1/3 of normal oil level, thus maintaining a
clean, non-corrosive and abrasion-free lubricating stable shaft sealing effect and prolonging seal life
environment is maintained. longer.

5 Leakage Sensor 6 Seal Pressure Relief Ports

Detects flooding into the oil chamber that may occur Protect the mechanical seal from pump pressure. They 5
in a worst case scenario. When flooding is detected, also protect the seal face by discharging wear 3 4
signals are sent to operate the indicator lamps particles.
through the external control panel. 6
7
7 Dual Back-to-Back Impellers 8 Galvanic Anodes
Reduce the thrust load applied to the impellers and Protect the pump against corrosive potential gen- 8
enhance bearing endurance. erated during the drainage of wastewater.

S.S. 3000min-1 S.S. 3600min-1

240 240

230 230

220 220

210 LH 210 L
H
41 41
Total Head (m)

Total Head (m)

10 10
200 W 200
W
190 190

180 180

170 170

160 160

150 150

0 0
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2
Capacity (m3/min) Capacity (m3/min)

Pump Motor
Discharge Bore & Connection 100mm, JIS 20kg/cm Flange 2
Output 110kW, 2-pole
Impeller Closed ( Dual) / High-chromium Cast Iron Phase Three
Mouth Ring High-chromium Cast Iron Type Dry-type Submersible Induction Motor
Labyrinth Ring 630 Stainless Steel Miniature Thermal Protector
Protection Device ( Built-in )
Leakage Sensor
Casing Gray Cast Iron   
Cable 20m / Chloroprene Rubber
Double Mechanical Seal (with Oil Lifter) /
Shaft Seal

Shaft Sleeve
Silicon Carbide
630 Stainless Steel
Measurement
Dimensions L x W x H 616 x 592 x 1825mm
Galvanic Anode Aluminium Alloy
Dry Weight ( excluding Cable ) 1270kg

We reserve the right to change the specifications and designs for improvement without prior notice.

Your Dealer

Printed in Japan CAT. IB119-A QR-D-H-R