Professional Documents
Culture Documents
Eng Handbook 4
Eng Handbook 4
Headquarters
1510 Gehman Road
Kulpsville, PA 19443
USA
Engineering Handbook
Section I – Introduction
MRC History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Catalog and speed rating disclaimer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Warranty statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Identification system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Bearing symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Identification of non-standard variants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Descriptive manufacturing suffixes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Telephone and fax numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
1
BEARING
INTRODUCTION ENGINEERING DATA MARATHON SERIES MADE-TO-ORDER
SPECIFICATION TABLES
Introduction
MRC Bearing Services
2
Engineering Handbook
Non-Standard Variants
Single-Row Angular Contact, Split Ring, 9000U, 9000UP, 97000U and 97000UP Series
Specialty Bearings
ABEC Tolerances
Lubrication
Vibration Data
3
4
Section I
Introduction
5
MRC History MRC Bearing Services
6
Catalog and Speed Rating
Disclaimer and Warranty
Disclaimer Warranty
The contents of this catalog are the copyright of MRC Bearing Services warrants that products sold
the publishers and may not be reproduced (even by it shall be free from defects in material and
extracts) unless permission is granted. Every care workmanship. MRC Bearing Services’ obligation
has been taken to insure the accuracy of the under this warranty is expressly limited to furnishing
information contained in this catalog but no without additional charge a replacement, or at its
liability can be accepted for any errors or option, repairing or issuing credit for any product
omissions. which shall within one year from the date of sale be
returned freight prepaid to the plant designated by
Listing in this catalog does not necessarily imply an MRC Bearing Services representative and which
product availability. Cage type speed adjustment upon inspection is determined by MRC Bearing
factor footnotes does not mean that particular Services to be defective in materials or
cage variants are available. workmanship. Complete information as to service,
mounting and relubrication should accompany any
The designs and load ratings shown in this product returned for inspection. The provisions of
catalog are those being used at the time of this warranty shall not apply to any MRC Bearing
publication. The possibility exists that the Services product which has been subjected to
designs and ratings may be changed to reflect misuse, improper mounting, assembly or lubrication;
product improvement or may be procured from or which has been repaired or altered if such repair
a different company facility. To determine or alteration in the judgement o MRC Bearing
current conditions, contact MRC Bearing Services would adversely affect performance of the
Services Product Engineering. product.
Interchange Information
This warranty is in lieu of all other warranties,
expressed or implied, including any limited
warranty of merchantability or fitness for a
Interchanges provided in this catalog can provide a particular purpose and is also in lieu of all other
fast conversion of manufacturer numbers to MRC obligations or liabilities on the part of MRC
equivalents. Please note that interchanges are made Bearing Services, including any obligation or
on an application basis and may not be completely liability arising from contract, tort or otherwise
identical to MRC Bearing Services products. Basic for damages and in no event shall seller be liable
interchanges indicate overall compatible design. The hereunder or otherwise for loss of profits;
interchange information was compiled using data special, incidental, or consequential damages of
available at the time of publication; however, SKF any kind. There are no warranties, expressed or
USA Inc. and MRC Bearing Services assume no implied, made by MRC Bearing Services, except
responsibility or liability for errors or omissions. Also, the warranty against defects in material and
bearing illustrations depict closure grooves; however, workmanship set forth above. MRC Bearing
actual bearings may or may not have closure Services and SKF USA Inc. neither assume nor
grooves. authorize any other person or firm to assume for
it any other obligation or liability in connection
with its products.
7
Identification System for MRC Bearings MRC Bearing Services
METRIC RADIAL BEARINGS
R07
203SZZ-0001 0001 = MRC INTERNAL SUFFIX CODE
STEEL/C3/ABEC-1 R07 = DATE CODE
2 03 S ZZ
R07
7308 PJDU - H501 H501 = MRC INTERNAL SUFFIX CODE
PRESSED BRASS/ABEC-3 R07 = DATE CODE
SERIES TYPE
1900 EXTREMELY LIGHT BB PUMPAC DIAMOND
100K EXTRA LIGHT C DOUBLE-ROW, CONRAD
200 LIGHT M DOUBLE-ROW, MAXIMUM CAPACITY
300 MEDIUM P 40˚ CONTACT ANGLE,
400 HEAVY COUNTERBORED OUTER
5200 DOUBLE-ROW, LIGHT PJ 40˚ CONTACT ANGLE, COUNTER-
5300 DOUBLE-ROW, MEDIUM BORED INNER AND OUTER
5400 DOUBLE-ROW, HEAVY R 15˚ CONTACT ANGLE, COUNTER-
7100K ANGULAR CONTACT, EXTRA LIGHT BORED OUTER
7200 ANGULAR CONTACT, LIGHT SB DOUBLE-ROW, CONRAD
7300 ANGULAR CONTACT, MEDIUM SBK DOUBLE-ROW, CONRAD WITH
7400 ANGULAR CONTACT, HEAVY CLOSURES
8000 PUMPAC U 29˚ CONTACT ANGLE, SPLIT RING ACCESSORIES
9200 ANGULAR CONTACT, SPLIT RING, LIGHT UP 40˚ CONTACT ANGLE, SPLIT RING F ONE SHIELD
9300 ANGULAR CONTACT, SPLIT RING, U2 MATCHED SET OF7000 DT/9000 UDT FF TWO SHIELDS
MEDIUM 29˚ CONTACT ANGLE Z ONE SEAL
97200 7200/9200 MATCHED SET, LIGHT UP2 MATCHED SET OF 7000 PDT/9000 ZZ TWO SEALS
97300 7300/9300 MATCHED SET, MEDIUM UPDT, 40˚ CONTACT ANGLE
73 08 PJ DU
9
Bearing Symbols MRC Bearing Services
BWF Double-row, integral shaft ball bearing, with two seals. BWF4800
10
Bearing Symbols
11
Bearing Symbols MRC Bearing Services
12
Bearing Symbols
FFSG Two felt seals and snap ring, replaced by 488XXX. 203FFSG
13
Bearing Symbols MRC Bearing Services
FSF One felt seal and one shield, replaced by 87XXX. 203FSF
One felt seal and one shield with snap ring on seal
FSFG side. 203FSFG
FSG One felt seal with snap ring on open side of bearing. 209FSG
14
Bearing Symbols
G FS One felt seal with snap ring on same side as seal. G209FS
One felt seal and one shield with snap ring on shield
G FSF side, replaced by 487xxx, . G209FSF
15
Bearing Symbols MRC Bearing Services
16
Bearing Symbols
17
Bearing Symbols MRC Bearing Services
18
Bearing Symbols
19
Bearing Symbols MRC Bearing Services
20
Bearing Symbols
RDT Single-row, split inner ring bearing, 20˚ contact angle. 309RDT1¹|₂
REP H Airframe bearing, rod end type, with hollow shank. REP3H5
REP S Airframe bearing, rod end type, with solid shank. REP4S10
21
Bearing Symbols MRC Bearing Services
22
Bearing Symbols
23
Bearing Symbols MRC Bearing Services
24
Bearing Symbols
25
Prefix/Suffix Symbols for Single-Row
Bearing Non-Standard Variants MRC Bearing Services
Nomenclature
S–Single Row Deep Groove Type F–Shield
M–Single Row Filling Notch Type Z–Seal
R–15° Angular Contact Type G–Snap Ring
WI–Wide Inner Ring Filling Notch Type FS–Felt Seal
SWI–Wide Inner Ring Non-Filling Notch Type X–Tapered Bore
When single seal is used, seal symbol (Z) replaces (F)
in designations shown except for Filling Notch (M) Type
MF X–M G–MFZ
MG MXF FZG–M
MX FZ–MG SFX
26
Prefix/Suffix Symbols for Single-Row
Bearing Non-Standard Variants
Nomenclature
S–Single Row Deep Groove Type F–Shield
M–Single Row Filling Notch Type Z–Seal
R–15° Angular Contact Type G–Snap Ring
WI–Wide Inner Ring Filling Notch Type FS–Felt Seal
SWI–Wide Inner Ring Non-Filling Notch Type X–Tapered Bore
When single seal is used, seal symbol (Z) replaces (F)
in designations shown except for Filling Notch (M) Type
SWIF RF RX
F–SWI RG X–R
FSFG G–RF
27
Prefix/Suffix Symbols for Double-Row
Bearing Non-Standard Variants MRC Bearing Services
Nomenclature
M–Filling Notch Type
C–Non-Filling Notch Type
F–Shield
Z–Seal
G–Snap Ring
28
MRC Manufacturing Suffixes
204SZZ H501
A four digit manufacturing suffix is used by MRC The standard MRC part number is sufficient for
internally to define bearing specifications as well as specifying customer requirements for all “Stock”
to track such information as plant-of-manufacture as sizes. The use of a non-descriptive manufacturing
product is distributed throughout the MRC suffix permits minor changes to the design and
warehousing network. This suffix is assigned manufacture of standard product without a confusing
sequentially within the MRC computer system and nomenclature change. The revised product may still
can only be cross-referenced internally by the MRC be tracked through distribution by the four digit
Customer Service Representative. manufacturing suffix.
29
MRC Descriptive Part Suffixes MRC Bearing Services
30
The six primary features of the services
provided to our customers are listed below:
• MRC is always one 1-800-MRC-7000 phone call
away—saving time in response to your customer.
• Fax number toll-free at 888-322-4672
• Immediate attention is given to technical questions by
our in-house engineering department, (215) 513-4700.
• MRC Technical Services experts are able to address
bearing problems in the field and offer solutions.
• MRC provides bearing failure analysis in problem
applications.
• Friendly, knowledgeable customer service people
are able to take important action on your requests.
• Many servicing warehouses assure inventory
accessibility in all parts of the country.
31
32
BEARING
INTRODUCTION ENGINEERING DATA MARATHON SERIES MADE-TO-ORDER
SPECIFICATION TABLES
Bearing
Specification
Tables
Section II
Bearing Specification Tables
33
34
MRC Bearing Series
35
Bearing Type Cage Contact Performance Characteristics
Angle Level Speed Radial Axial
Capacity Capacity
36
Bearing Types Summary Chart
Description
Ordinarily supplied with loose internal clearance. Outer and inner races have full shoulders. Has equal load-
carrying capacity in either direction. Recommended for moderately heavy radial loads, thrust loads in either
direction, or combination loads.
Ordinarily supplied with standard internal clearance. Has inch boundary dimensions. Outer and inner races
have full shoulders. Has equal load-carrying capacity in either direction. Recommended for moderately heavy
radial loads, thrust loads in either direction, or combination loads.
Ordinarily supplied with standard internal clearance. This type has a filling notch on one side of the inner and
outer rings to insert a maximum ball complement. Can carry heavy radial load or combined radial and thrust
load where the radial load predominates. Not recommended for pure thrust loads or combined loads where
thrust load predominates.
Supplied with loose internal clearance for normal applications. Counterbored outer ring to assemble maximum
ball complement. Outer ring is heated in order to assemble. Can carry heavy radial load, moderate thrust load
in one direction only, or combined loads where thrust load is against the heavy shoulder on the outer ring.
C type ordinarily supplied with loose internal clearance. Has full shoulders and no filling notches. Has
outwardly converging contact angles. C type will support heavy radial loads, and equally heavy thrust load in
either direction, or heavy combined radial and thrust loads. M type ordinarily supplied with standard internal
clearance. Has filling notches on one side only for inserting maximum ball compliment. Has outwardly
converging contact angles. M type has heavy radial capacity. Also has moderate thrust capacity in one
direction and can take light thrust load in reversing direction.
Counterbored outer ring, non-separable type. Ordinarily available in single and paired variants. Paired
variants typically supplied with line-to-line internal clearance. Other°s of internal clearance/preload
may be necessary for special conditions. Two-piece pressed steel cage for normal use or one-piece non-metallic
or solid brass cage for high speed, high operating temperature, or severe vibration application. High thrust
load in one direction, combined radial and thrust load where thrust load predominates. Should not be used
for radial loads only.
Similar in design to the 7000 Series bearing. Thrust capacity is 1.18 to 1.4 times that of the 7000 Series, varies
with individual sizes. Restricted to primarily thrust loads. Should not be used for radial loads only or
combined radial and thrust loads where radial load predominates.
Counterbored outer ring, non-separable type. Similar to the Type R angular contact except that it has inch
dimensions. It also has a relatively light cross section for space constraints. Can carry heavy radial load,
moderate thrust load in one direction only, or combined loads where thrust load is against the heavy shoulder
on the outer ring.
Designed with two-piece inner ring and one-piece outer ring and snap ring. Differs from the 5000C and
M Types because of its 40° contact angle and split inner ring. Also has a machined brass cage and reduced
axial clearance. Can carry very heavy thrust loads in either direction or combined loads where the
thrust load predominates.
Bearing assembly consists of a 40° and 15° bearing, ABEC-3 precision tolerances, reduced axial clearance, and
machined brass cages. Can carry high thrust load in one direction and light reversing thrust load in the opposite
direction. The lower contact angle of the back bearing helps prevent ball skidding during periods of no load.
37
Bearing Type Cage Contact Performance Characteristics
Angle Level Speed Radial Axial
Capacity Capacity
Extremely High
Very High
High
Moderate
38
Bearing Types Summary Chart
Description
Consists of two 15° bearings as opposed to one 40° and one 15°, ABEC-3 precision tolerances, reduced
axial clearance, and machined brass cages. Can carry predominantly radial load with intermittent thrust load
in either direction. Very similar performance to the 7000R series, except that it is a back-to-back paired
arrangement.
Can carry very high thrust loads in one direction and light reversing thrust load in the opposite direction.
The pair of 40° “A” bearings in tandem provides very high thrust capacity in the primary direction,
while the 15° “B” bearing handles any reversing thrust load.
Designed with solid one-piece outer ring and two-piece inner ring, maximum ball compliment and one-piece
machined brass cage. Can carry greater thrust in either direction than the Type S. May be used where there is
substantial radial load providing there is always sufficient thrust load present. Often paired with another
angular contact ball bearing in an assembly.
Paired assembly of a 9000U and a 7000 angular contact bearing. Assembly comes with axial clearance as
standard and provides the capacity of a triplex set in the boundary dimensions of a pair. Very heavy thrust load
capacity because of tandem assembly of 9000U and 7000 bearing in one direction. 9000U supports reversing
thrust load in the opposite direction.
Very similar to the 97000U2 series except that it has a 40° contact angle. Because of the higher contact angle,
this assembly has the highest thrust carrying capacity for its given boundary dimensions.
Series of corrosion resistant housings and bearings used in heavy wash down and contaminated environments
such as food, car wash, gypsum, etc. The unique double sealing arrangement makes Marathon units very
effective at keeping out solid and liquid contamination. These units incorporate an insert bearing based on
the Type S Conrad bearing so they can handle moderate radial loads and light thrust loads in either direction.
However, since they are set screwed to the shaft, the axial load carrying capacity is determined by the holding
power of the set screws.
ABEC-7 tolerances for machine tool applications that require high speeds and precise running accuracies.
Type DS are available in 15° and 25° contact angles. These bearings are normally used in paired arrangements.
They function very similarly to the Type R and 7000 series bearings except for the fact that they are much
higher precision.
ABEC-7 tolerances for high speeds required by machine tool spindles. Very high radial stiffness because of its
double row roller design. Very high radial load carrying capacity. Zero axial load carrying capacity because of
the shoulderless outer ring which allows the bearing to expand with shaft thermal growth.
ABEC-7 tolerances for high speed. Counterbored inner and outer ring construction. Very high axial stiffness
because of the 60° contact angle and larger quantity of small balls. Usually used in paired, triplex, or quad
sets in order to provide adequate stiffness and capacity for the given application conditions. Primarily designed
for high thrust loads and very little radial load because of the 60° contact angle.
Type DT has a one-piece outer ring construction with a two-piece inner ring construction. Like the Type J
bearing, it has a 60° contact angle. It is also a paired assembly. Its large quantity of small balls also provides
high axial stiffness as with the Type J bearings. The Type DT bearing can handle high thrust load in either
direction and virtually zero radial load. It is usually paired with a radial type bearing in order to isolate it
from any radial loading.
39
40
Single-Row Deep Groove
Ball Bearings, S-Type
The MRC conrad ball bearing is a single-row radial Cage Types and Materials
deep groove bearing with no filling notches. It can
carry significant radial loads, and, because of the This type of bearing is supplied with a pressed steel
uninterrupted raceway grooves and the high degree cage as standard; however, for special requirements,
of conformity between balls and raceways, it can it can be supplied with a two-piece riveted machined
carry substantial thrust loads in either direction, even cage of phenolic composition or bronze material.
at very high speeds. Single-row deep groove ball
bearings are offered open or with single or double
shields or seals, as well as with snap rings in various
combinations.
30 Extra Small 42
R Small Inch-Size 43
1800S Thin Section 44
1900S Extremely Light 45
100S Narrow-Type Light 46
100KS Extra Light 47
200S Light 48
300S Medium 49
400S Heavy 50
Cartridge Type 51
Hybrid Bearings 54
41
30 Series
Extra Small Size MRC Bearing Services
34 4 .1575 16 .6299 5 .1969 .30 .012 45 .07 1 470 330 600 135 43 000 50 000 30 000
35 5 .1969 19 .7480 6 .2362 .30 .012 96 .15 2 210 497 950 214 36 000 43 000 26 000
36 6 .2362 19 .7480 6 .2362 .30 .012 96 .15 2 210 497 950 214 36 000 43 000 26 000
37 7 .2756 22 .8661 7 .2756 .30 .012 110 .17 3 250 731 1 360 306 36 000 43 000 23 000
38 8 .3150 22 .8661 7 .2756 .30 .012 110 .17 3 250 731 1 360 306 36 000 43 000 23 000
39 9 .3543 26 1.0236 8 .3150 .64 .025 161 .25 4 620 1 040 1 960 441 28 000 34 000 20 000
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
Listed values are for pressed steel or polyamide cage, ABEC-1.
For phenolic composition cage, multiply by 1.66 for grease and 2.00 for oil. For machined bronze cage, multiply by 1.25 for grease and 1.50 for oil. For phenolic composition
cage, ABEC-5 or 7, multiply by 2.30 for grease and 2.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
42
R Series Small Inch-Size
R-2 3.2 .1250 9.5 .3750 4.0 .1562 4.0 .1562 .30 .012 19 .03 312 70 120 27 75 000 91 000 52 000
R-2-A 3.2 .1250 12.7 .5000 4.4 .1719 4.4 .1719 .30 .012 19 .03 312 70 120 27 75 000 91 000 52 000
R-3 4.8 .1875 12.7 .5000 4.0 .1562 5.0 .1960 .30 .012 39 .06 956 215 490 110 57 000 69 000 40 000
R-4 6.4 .2500 15.9 .6250 5.0 .1960 5.0 .1960 .30 .012 45 .07 1 480 332 620 139 44 000 54 000 31 000
R-4-A 6.4 .2500 19.1 .7500 5.6 .2188 7.1 .2812 .41 .016 71 .11 2 810 632 1 160 261 39 000 48 000 27 000
R-6 9.5 .3750 22.2 .8750 5.6 .2188 7.1 .2812 .41 .016 110 .17 3 320 746 1 340 301 31 000 38 000 21 000
R-8 12.7 .5000 28.6 1.1250 6.4 .2500 7.9 .3125 .41 .016 181 .28 5 070 1 140 2 400 540 24 000 29 000 16 000
R-10 15.9 .6250 34.9 1.3750 7.1 .2812 8.7 .3438 .79 .031 226 .35 6 050 1 360 3 250 731 18 000 22 000 13 000
R-12 19.1 .7500 41.3 1.6250 7.9 .3125 11.1 .4375 .79 .031 361 .56 9 360 2 100 5 100 1 150 16 000 19 000 11 000
R-14 22.2 .8750 47.6 1.8750 9.5 .3750 12.7 .5000 .79 .031 406 .63 10 100 2 270 5 850 1 320 14 000 17 000 9 600
R-16 25.4 1.0000 50.8 2.0000 9.5 .3750 12.7 .5000 .79 .031 406 .63 10 100 2 270 6 000 1 350 13 000 16 000 9 000
R-18 28.6 1.1250 54.0 2.1250 9.5 .3750 12.7 .5000 .79 .031 510 .79 12 500 2 810 7 500 1 690 11 000 14 000 7 900
R-20 31.8 1.2500 57.2 2.2500 9.5 .3750 12.7 .5000 .79 .031 613 .95 14 000 3 150 9 300 2 090 11 000 13 000 7 500
R-24 38.1 1.5000 66.7 2.6250 11.1 .4375 14.3 .5625 .79 .031 755 1.17 16 800 3 780 11 800 2 650 9 000 11 000 6 200
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
Listed values are for pressed steel or polyamide cage, ABEC-1.
For phenolic composition cage, multiply by 1.66 for grease and 2.00 for oil. For machined bronze cage, multiply by 1.25 for grease and 1.50 for oil. For phenolic composition
cage, ABEC-5 or 7, multiply by 2.30 for grease and 2.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
43
1800-S Thin Section Series MRC Bearing Services
1800S 10 .3937 19 .7480 5 .1969 .30 .012 62 .10 1 820 410 930 209 36 000 43 000 20 000
1801S 12 .4724 21 .8268 5 .1969 .30 .012 68 .11 1 900 427 1 040 234 32 000 38 000 19 000
1802S 15 .5906 24 .9449 5 .1969 .30 .012 80 .12 2 080 468 1 250 281 28 000 34 000 17 000
1803S 17 .6693 26 1.0236 5 .1969 .30 .012 91 .14 2 250 505 1 460 328 24 000 30 000 16 000
1804S 20 .7874 32 1.2598 7 .2756 .30 .012 141 .22 3 510 790 2 240 504 19 000 24 000 13 000
1805S 25 .9843 37 1.4567 7 .2756 .30 .012 184 .28 4 360 980 2 900 652 17 000 20 000 11 000
1806S 30 1.1811 42 1.6535 7 .2756 .30 .012 208 .32 4 490 1 010 3 400 764 15 000 18 000 9 500
1807S 35 1.3780 47 1.8504 7 .2756 .30 .012 233 .36 4 750 1 070 3 800 854 13 000 16 000 8 000
1808S 40 1.5748 52 2.0472 7 .2756 .30 .012 257 .40 4 940 1 110 4 150 933 11 000 14 000 7 500
1809S 45 1.7717 58 2.2835 7 .2756 .30 .012 315 .49 6 050 1 360 5 100 1 150 9 500 12 000 6 700
1810S 50 1.9685 65 2.5591 7 .2756 .30 .012 347 .54 6 240 1 400 5 500 1 240 9 000 11 000 6 000
1811S 55 2.1654 72 2.8346 9 .3543 .30 .012 454 .70 8 320 1 870 7 350 1 650 8 500 10 000 5 180
1812S 60 2.3622 78 3.0709 10 .3937 .30 .012 499 .77 8 710 1 960 8 000 1 800 7 500 9 000 4 800
1813S 65 2.5591 85 3.3465 10 .3937 .60 .025 679 1.05 11 700 2 630 11 000 2 470 7 000 8 500 4 500
1814S 70 2.7559 90 3.5433 10 .3937 .60 .025 741 1.15 12 100 2 720 11 800 2 650 6 700 8 000 4 300
1815S 75 2.9528 95 3.7402 10 .3937 .60 .025 803 1.24 12 500 2 810 12 900 2 900 6 300 7 500 4 000
1816S 80 3.1496 100 3.9370 10 .3937 .60 .025 864 1.32 13 000 2 920 13 700 3 080 6 000 7 000 3 600
1817S 85 3.3465 110 4.3307 13 .5118 1.0 .040 1 230 1.90 19 500 4 380 19 600 4 410 5 300 6 300 3 400
1818S 90 3.5433 115 4.5276 13 .5118 1.0 .040 1 280 1.98 19 500 4 380 20 400 4 590 5 300 6 300 3 200
1819S 95 3.7402 120 4.7244 13 .5118 1.0 .040 1 330 2.06 19 900 4 470 21 200 4 770 5 000 6 000 3 000
1820S 100 3.9370 125 4.9213 13 .5118 1.0 .040 1 380 2.14 20 300 4 560 22 000 4 950 4 800 5 600 3 000
1821S 105 4.1339 130 5.1181 13 .5118 1.0 .040 1 480 2.29 20 800 4 680 23 600 5 310 4 500 5 300 2 800
1822S 110 4.3307 140 5.5118 16 .6299 1.0 .040 1 910 2.95 28 100 6 320 30 500 6 860 4 300 5 000 2 600
1824S4) 120 4.7244 150 5.9055 16 .6299 1.0 .040 2 060 3.19 29 100 6 540 32 500 7 310 3 800 4 500 2 400
1826S4) 130 5.1181 165 6.4961 18 .7087 1.0 .040 2 660 4.13 37 700 8 480 43 000 9 670 3 600 4 300 2 200
1828S4) 140 5.5118 175 6.8898 18 .7087 1.0 .040 2 870 4.46 39 000 8 770 46 500 10 500 3 400 4 000 2 000
1830S4) 150 5.9055 190 7.4803 20 .7874 1.0 .040 3 540 5.49 48 800 11 000 57 000 12 800 3 000 3 600
1832S4) 160 6.2992 200 7.8740 20 .7874 1.0 .040 3 690 5.71 49 400 11 100 60 000 13 500 2 800 3 400
1834S4) 170 6.6929 215 8.4646 22 .8661 1.0 .040 4 550 7.06 61 800 13 900 73 500 16 500 2 600 3 200
1836S4) 180 7.0866 225 8.8583 22 .8661 1.0 .040 4 730 7.34 62 400 14 000 76 500 17 200 2 400 3 000
1838S4) 190 7.4803 240 9.4488 24 .9449 1.5 .060 5 690 8.81 74 100 16 700 91 500 20 600 2 200 2 800
1840S4) 200 7.8740 250 9.8425 24 .9449 1.5 .060 5 910 9.17 76 100 17 100 95 000 21 400 2 200 2 800
1844S4) 220 8.6614 270 10.6299 24 .9449 1.5 .060 6 370 9.87 78 000 17 500 102 000 22 900 1 900 2 400
1848S4) 240 9.4488 300 11.8110 28 1.1024 2.0 .080 8 670 13.4 108 000 24 300 140 000 31 500 1 800 2 200
1852S4) 260 10.2362 320 12.5984 28 1.1024 2.0 .080 9 330 14.5 111 000 25 000 150 000 33 700 1 700 2 000
1856S4) 280 11.0236 350 13.7795 33 1.2992 2.0 .080 11 500 17.8 138 000 31 000 183 000 41 100 1 600 1 900
1860S4) 300 11.8110 380 14.9606 38 1.4961 2.0 .080 14 200 22.0 172 000 38 700 228 000 51 300 1 400 1 700
1864S4) 320 12.5984 400 15.7480 38 1.4961 2.0 .080 14 700 22.9 172 000 38 700 236 000 53 100 1 300 1 600
1868S4) 340 13.3858 420 16.5354 38 1.4961 2.0 .080 15 900 24.6 178 000 40 000 255 000 57 300 1 200 1 500
1872S4) 360 14.1732 440 17.3228 38 1.4961 2.0 .080 16 400 25.5 182 000 40 900 260 000 58 500 1 100 1 400
1876S4) 380 14.9606 480 18.8976 46 1.8110 2.0 .080 22 700 35.3 242 000 54 400 365 000 82 100 1 000 1 300
1880S4) 400 15.7480 500 19.6850 46 1.8110 2.0 .080 23 700 36.7 247 000 55 500 380 000 85 400 1 000 1 300
1884S4) 420 16.5354 520 20.4724 46 1.8110 2.0 .080 24 600 38.1 251 000 56 400 390 000 87 700 950 1 200
1888S4) 440 17.3228 540 21.2598 46 1.8110 2.0 .080 25 500 39.5 255 000 57 300 405 000 91 000 900 1 100
1892S4) 460 18.1102 580 22.8346 56 2.2047 2.5 .100 33 300 51.7 312 000 70 100 530 000 119 000 900 1 100
1896S4) 480 18.8976 600 23.6220 56 2.2047 2.5 .100 34 700 53.7 325 000 73 100 560 000 126 000 850 1 000
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2) Listed values are for pressed steel cage for 1800S through 1828S and 1834S and 1856S. All others for outer land guided machined bronze.
The values have been determined through historical application and practice. For a more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
4) Typically non-stocked sizes, please check availability before designing into equipment.
44
1900-S Series Extremely Light Series
1900S 10 .3937 22 .8661 6 .2362 .30 .012 84 .13 2 510 565 1 120 252 34 000 40 000 19 000
1901S 12 .4724 24 .9449 6 .2362 .30 .012 103 .16 2 910 655 1 500 337 30 000 36 000 18 000
1902S 15 .5906 28 1.1024 7 .2756 .30 .012 142 .22 4 030 906 2 040 459 24 000 30 000 16 000
1903S 17 .6693 30 1.1811 7 .2756 .30 .012 155 .24 4 360 980 2 320 522 22 000 28 000 14 000
1904S 20 .7874 37 1.4567 9 .3543 .30 .012 252 .39 6 370 1 430 3 650 821 18 000 22 000 12 000
1905S 25 .9843 42 1.6535 9 .3543 .30 .012 271 .42 6 630 1 490 4 150 933 16 000 19 000 10 000
1906S 30 1.1811 47 1.8504 9 .3543 .30 .012 317 .49 7 280 1 640 5 000 1 120 14 000 17 000 8 500
1907S 35 1.3780 55 2.1654 10 .3937 .64 .025 432 .67 9 560 2 150 6 800 1 530 11 000 14 000 7 500
1908S 40 1.5748 62 2.4409 12 .4724 .64 .025 637 .99 13 800 3 100 10 000 2 250 10 000 13 000 6 700
1909S 45 1.7717 68 2.6772 12 .4724 .64 .025 683 1.06 14 000 3 150 10 800 2 430 9 000 11 000 6 000
1910S 50 1.9685 72 2.8346 12 .4724 .64 .025 728 1.13 14 600 3 280 11 800 2 650 8 500 10 000 5 600
1911S 55 2.1654 80 3.1496 13 .5118 1.0 .040 864 1.34 16 500 3 710 14 000 3 150 8 000 9 500 5 000
1912S 60 2.3622 85 3.3465 13 .5118 1.0 .040 864 1.34 16 500 3 710 14 300 3 210 7 500 9 000 4 500
1913S 65 2.5591 90 3.5433 13 .5118 1.0 .040 968 1.50 17 400 3 910 16 000 3 600 6 700 8 000 4 300
1914S 70 2.7559 100 3.9370 16 .6299 1.0 .040 1 300 2.01 23 800 5 350 21 200 4 770 6 300 7 500 4 000
1915S 75 2.9528 105 4.1339 16 .6299 1.0 .040 1 370 2.13 24 200 5 440 22 400 5 040 6 000 7 000 3 600
1916S 80 3.1496 110 4.3307 16 .6299 1.0 .040 1 450 2.25 25 100 5 640 24 000 5 400 5 600 6 700 3 400
1917S 85 3.3465 120 4.7244 18 .7087 1.0 .040 1 810 2.81 31 900 7 170 30 000 6 740 5 300 6 300 3 200
1918S 90 3.5433 125 4.9213 18 .7087 1.0 .040 1 920 2.97 32 500 7 310 31 500 7 080 5 000 6 000 3 100
1919S 95 3.7402 130 5.1181 18 .7087 1.0 .040 2 025 3.14 33 800 7 600 33 500 7 530 4 800 5 600 2 900
1920S 100 3.9370 140 5.5118 20 .7874 1.0 .040 2 550 3.96 42 300 9 510 41 500 9 330 4 500 5 300 2 700
1921S 105 4.1339 145 5.7087 20 .7874 1.0 .040 2 770 4.18 44 200 9 940 44 000 9 890 4 300 5 000 2 600
1922S 110 4.3307 150 5.9055 20 .7874 1.0 .040 2 770 4.18 43 600 9 800 44 000 9 890 4 000 4 800 2 500
1924S 120 4.7244 165 6.4961 22 .8661 1.0 .040 3 460 5.36 55 300 12 400 57 000 12 800 3 600 4 300 2 300
1926S4) 130 5.1181 180 7.0866 24 .9449 1.5 .060 4 100 6.35 65 000 14 600 67 000 15 100 3 400 4 000 2 100
1928S4) 140 5.5118 190 7.4803 24 .9449 1.5 .060 4 320 6.70 66 300 14 900 71 000 16 000 3 200 3 800 2 000
1930S4) 150 5.9055 210 8.2677 28 1.1024 2.0 .080 5 670 8.78 88 400 19 900 93 000 20 900 2 800 3 400 1 800
1932S4) 160 6.2992 220 8.6614 28 1.1024 2.0 .080 6 000 9.30 92 300 20 700 98 000 22 000 2 600 3 200 1 700
1934S4) 170 6.6929 230 9.0551 28 1.1024 2.0 .080 6 330 9.82 93 600 21 000 104 000 23 400 2 400 3 000 1 600
1936S4) 180 7.0866 250 9.8425 33 1.2992 2.0 .080 8 060 12.5 119 000 26 800 132 000 29 700 2 200 2 800 1 500
1938S4) 190 7.4803 260 10.2362 33 1.2992 2.0 .080 8 060 12.5 117 000 26 300 134 000 30 100 2 200 2 800 1 400
1940S4) 200 7.8740 280 11.0236 38 1.4961 2.0 .080 10 200 15.8 148 000 33 300 166 000 37 300 2 000 2 600 1 300
1944S4) 220 8.6614 300 11.8110 38 1.4961 2.0 .080 10 800 16.7 151 000 33 900 176 000 39 600 1 900 2 400 1 200
1948S4) 240 9.4488 320 12.5984 38 1.4961 2.0 .080 11 900 18.5 159 000 35 800 196 000 44 100 1 800 2 200 1 100
1952S4) 260 10.2362 360 14.1732 46 1.8110 2.0 .080 16 400 25.4 212 000 47 700 270 000 60 700 1 600 1 900 1 000
1956S4) 280 11.0236 380 14.9606 46 1.8110 2.0 .080 17 300 26.8 216 000 48 600 285 000 64 100 1 500 1 800 950
1960S4) 300 11.8110 420 16.5354 56 2.2047 3.0 .120 22 700 35.1 270 000 60 700 375 000 84 300 1 300 1 600 800
1964S4) 320 12.5984 440 17.3228 56 2.2047 3.0 .120 24 000 37.2 276 000 62 100 390 000 87 700 1 200 1 500 750
1968S4) 340 13.3858 460 18.1102 56 2.2047 3.0 .120 25 300 39.3 281 000 63 200 415 000 93 300 1 100 1 400 700
1972S4) 360 14.1732 480 18.8976 56 2.2047 3.0 .120 26 700 41.3 291 000 65 400 440 000 98 900 1 100 1 400 700
1976S4) 380 14.9606 520 20.4724 65 2.5591 4.0 .160 32 400 50.2 338 000 76 000 530 000 119 000 1 000 1 300 650
1980S4) 400 15.7480 540 21.2598 65 2.5591 4.0 .160 34 100 52.8 345 000 77 000 560 000 126 000 950 1 200 600
1984S4) 420 16.5354 560 22.0472 65 2.5591 4.0 .160 35 800 55.5 351 000 78 900 585 000 132 000 900 1 100 550
1988S4) 440 17.3228 600 23.6220 74 2.9134 4.0 .160 43 100 66.8 410 000 92 200 710 000 160 000 900 1 100 550
1992S4) 460 18.1102 620 24.4094 74 2.9134 4.0 .160 45 400 70.3 423 000 95 100 750 000 169 000 850 1 000 550
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2) Listed values are for pressed steel or polyamide cage, ABEC-1.
For phenolic composition cage, multiply by 1.66 for grease and 2.00 for oil. For machined bronze cage, multiply by 1.25 for grease and 1.50 for oil. For phenolic composition
cage, ABEC-5 or 7, multiply by 2.30 for grease and 2.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM. 45
4) Typically non-stocked sizes, please check availability before designing into equipment.
100-S Narrow-Type Light Series MRC Bearing Services
NOTE: This series is obsoleted but is still manufactured in a few sizes for replacement parts,
please check availability before designing into equipment.
102-S 10 .3937 32 1.2598 9 .3543 .51 .02 181 .28 5 200 1 170 2 450 551 24 000 29 000
103-S 15 .5906 37 1.4567 9 .3543 .51 .02 284 .44 7 800 1 750 3 550 798 21 000 26 000
104-S 20 .7874 42 1.6535 9 .3543 .51 .02 361 .56 9 360 2 100 5 100 1 150 17 000 21 000
105-S 25 .9843 52 2.0472 9 .3543 1.0 .04 458 .71 12 100 2 710 6 700 1 510 14 000 17 000
106-S 30 1.1811 62 2.4409 10 .3937 1.0 .04 632 .98 15 600 3 500 9 300 2 090 11 000 14 000
107-S 35 1.3780 70 2.7559 10 .3937 1.0 .04 755 1.17 16 800 3 780 11 600 2 610 10 000 12 000
108-S 40 1.5748 80 3.1496 11 .4331 1.0 .04 819 1.27 18 200 4 100 12 900 2 900 9 000 11 000
109-S 45 1.7717 85 3.3465 11 .4331 1.0 .04 1 010 1.56 19 800 4 450 16 300 3 670 8 000 9 700
110-S 50 1.9685 90 3.5433 11 .4331 1.0 .04 1 010 1.56 19 900 4 470 16 600 3 730 7 400 9 000
111-S 55 2.1654 100 3.9370 12 .4724 1.0 .04 1 220 1.89 23 400 5 260 20 000 4 500 6 800 8 300
112-S 60 2.3622 105 4.1339 12 .4724 1.0 .04 1 450 2.25 27 000 6 080 23 600 5 300 6 100 7 400
113-S 65 2.5591 115 4.5276 14 .5512 1.0 .04 1 450 2.25 27 000 6 080 23 600 5 300 6 100 7 400
114-S 70 2.7559 120 4.7244 14 .5512 1.0 .04 1 700 2.64 31 200 7 010 28 000 6 300 5 400 6 600
115-S 75 2.9528 130 5.1181 16 .6299 1.5 .06 2 260 3.50 42 300 9 520 36 000 8 090 5 100 6 200
116-S 80 3.1496 135 5.3150 16 .6299 1.5 .06 2 420 3.75 44 200 9 940 39 000 8 770 4 800 5 900
117-S 85 3.3465 145 5.7087 18 .7087 1.5 .06 2 850 4.42 52 700 11 800 45 500 10 200 4 500 5 500
118-S 90 3.5433 150 5.9055 18 .7087 1.5 .06 2 850 4.42 52 700 11 800 46 500 10 500 4 300 5 200
119-S 95 3.7402 160 6.2992 20 .7874 1.5 .06 3 530 5.47 63 700 14 300 57 000 12 800 4 000 4 900
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
Listed values are for pressed steel or polyamide cage, ABEC-1.
For phenolic composition cage, multiply by 1.66 for grease and 2.00 for oil. For machined bronze cage, multiply by 1.25 for grease and 1.50 for oil. For phenolic composition
cage, ABEC-5 or 7, multiply by 2.30 for grease and 2.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
46
100-KS Extra Light Series
KSF KSZ KSFF KSZZ KSFZ KSG KSFG KSZG KSFFG KSZZG
One Shield One Seal Two Shields Two Seals Shield & Snap-Ring One Shield Seal & Two Shields Two Seals &
Seal & Snap-Ring Snap-Ring & Snap-Ring Snap-Ring
100-KS 10 .3937 26 1.0236 8 .3150 .30 .012 181 .28 4 620 1 040 1 960 440 30 000 36 000 19 000
101-KS 12 .4724 28 1.1024 8 .3150 .30 .012 181 .28 5 070 1 140 2 360 530 26 000 32 000 17 000
102-KS 15 .5906 32 1.2598 9 .3543 .30 .012 206 .32 5 590 1 260 2 850 640 22 000 28 000 14 000
103-KS 17 .6693 35 1.3780 10 .3937 .30 .012 226 .35 6 050 1 360 3 250 730 19 000 24 000 13 000
104-KS 20 .7874 42 1.6535 12 .4724 .64 .025 361 .56 9 360 2 100 5 000 1 120 17 000 20 000 11 000
105-KS 25 .9843 47 1.8504 12 .4724 .64 .025 458 .71 11 200 2 520 6 550 1 470 15 000 18 000 9 500
106-KS 30 1.1811 55 2.1654 13 .5118 1.0 .04 561 .87 13 300 2 990 8 300 1 870 12 000 15 000 8 000
107-KS 35 1.3780 62 2.4409 14 .5512 1.0 .04 691 1.07 15 800 3 570 10 200 2 290 10 000 13 000 7 000
108-KS 40 1.5748 68 2.6772 15 .5906 1.0 .04 909 1.41 20 800 4 680 11 600 2 610 9 500 12 000 6 300
109-KS 45 1.7717 75 2.9528 16 .6299 1.0 .04 1 090 1.69 23 400 5 270 16 600 3 730 9 000 11 000 5 600
110-KS 50 1.9685 80 3.1496 16 .6299 1.0 .04 1 180 1.83 24 700 5 560 18 000 4 050 8 500 10 000 5 000
111-KS 55 2.1654 90 3.5433 18 .7087 1.0 .04 1 390 2.16 28 100 6 320 21 600 4 880 7 500 9 000 4 500
112-KS 60 2.3622 95 3.7402 18 .7087 1.0 .04 1 610 2.49 32 500 7 310 25 000 5 620 6 700 8 000 4 300
113-KS 65 2.5591 100 3.9370 18 .7087 1.0 .04 1 730 2.68 33 800 7 600 27 000 6 070 6 300 7 500 4 000
114-KS 70 2.7559 110 4.3307 20 .7874 1.0 .04 2 100 3.25 41 000 9 220 32 500 7 310 6 000 7 000 3 600
115-KS 75 2.9528 115 4.5276 20 .7874 1.0 .04 2 260 3.50 42 300 9 510 35 500 7 970 5 600 6 700 3 400
116-KS 80 3.1496 125 4.9213 22 .8661 1.0 .04 2 650 4.11 50 700 11 400 41 500 9 330 5 300 6 300 3 200
117-KS 85 3.3465 130 5.1181 22 .8661 1.0 .04 2 860 4.43 52 700 11 800 45 000 10 100 5 000 6 000 3 000
118-KS 90 3.5433 140 5.5118 24 .9449 1.5 .06 3 280 5.08 61 800 13 900 51 000 11 500 4 800 5 600 2 800
119-KS 95 3.7402 145 5.7087 24 .9449 1.5 .06 3 530 5.47 63 700 14 300 54 000 12 100 4 500 5 300 2 800
120-KS 100 3.9370 150 5.9055 24 .9449 1.5 .06 3 530 5.47 63 700 14 300 54 000 12 100 4 300 5 000 2 600
121-KS 105 4.1339 160 6.2992 26 1.0236 2.0 .08 4 330 6.72 79 300 17 800 65 500 14 700 4 000 4 800 2 400
122-KS 110 4.3307 170 6.6929 28 1.1024 2.0 .08 4 660 7.23 81 800 18 400 73 500 16 500 3 800 4 500 2 400
124-KS 120 4.7244 180 7.0866 28 1.1024 2.0 .08 5 000 7.75 85 200 19 100 80 000 18 000 3 400 4 000 2 200
126-KS 130 5.1181 200 7.8740 33 1.2992 2.0 .08 5 960 9.24 106 000 23 800 100 000 22 500 3 200 3 800 2 000
128-KS4) 140 5.5118 210 8.2677 33 1.2992 2.0 .08 6 900 10.7 111 000 25 000 108 000 24 300 3 000 3 600 1 800
130-KS4) 150 5.9055 225 8.8583 35 1.3780 2.0 .08 8 385 13.0 125 000 28 100 125 000 28 100 2 600 3 200 1 700
132-KS4) 160 6.2992 240 9.4488 38 1.4961 2.0 .08 9 030 14.0 143 000 32 100 143 000 32 100 2 400 3 000 1 600
134-KS4) 170 6.6929 260 10.2362 42 1.6535 2.0 .08 11 800 18.3 168 000 37 800 173 000 38 900 2 200 2 800 1 500
136-KS4) 180 7.0866 280 11.0236 46 1.8110 2.0 .08 11 400 17.7 190 000 42 700 200 000 45 000 2 000 2 600 1 400
138-KS4) 190 7.4803 290 11.4173 46 1.8110 2.0 .08 13 400 20.8 195 000 43 800 216 000 48 600 2 000 2 600 1 400
140-KS4) 200 7.8740 310 12.2047 51 2.0079 2.0 .08 15 900 24.6 216 000 48 600 245 000 55 100 1 900 2 400 1 300
144-KS4) 220 8.6614 340 13.3868 56 2.2047 2.5 .10 18 600 28.9 247 000 55 500 290 000 65 200 1 800 2 200 1 100
148-KS4) 240 9.4488 360 14.1732 56 2.2047 2.5 .10 19 500 30.2 255 000 57 300 315 000 70 800 1 700 2 000 1 000
152-KS4) 260 10.2362 400 15.7480 65 2.5591 3.0 .12 23 900 37.0 291 000 65 400 375 000 84 300 1 500 1 800 940
156-KS4) 280 11.0236 420 16.5354 65 2.5591 3.0 .12 25 700 39.9 302 000 67 900 405 000 91 000 1 400 1 700 890
160-KS4) 300 11.8110 460 18.1102 74 2.9134 3.0 .12 31 700 49.2 358 000 80 500 500 000 112 000 1 200 1 500 780
164-KS4) 320 12.5984 480 18.8976 74 2.9134 3.0 .12 34 000 52.7 371 000 83 400 540 000 121 000 1 100 1 400 730
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
Listed values are for pressed steel or polyamide cage, ABEC-1.
For phenolic composition cage, multiply by 1.66 for grease and 2.00 for oil. For machined bronze cage, multiply by 1.25 for grease and 1.50 for oil. For phenolic composition
cage, ABEC-5 or 7, multiply by 2.30 for grease and 2.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
4) Typically non-stocked sizes, please check availability before designing into equipment.
47
200-S Light Series MRC Bearing Services
200-S 10 .3937 30 1.1811 9 .3543 .64 .025 181 .28 5 070 1 140 2 360 531 24 000 30 000 17 000
201-S 12 .4724 32 1.2598 10 .3937 .64 .025 252 .39 6 890 1 550 3 100 697 22 000 28 000 15 000
202-S 15 .5906 35 1.3780 11 .4331 .64 .025 290 .45 7 800 1 750 3 250 843 19 000 24 000 13 000
203-S 17 .6693 40 1.5748 12 .4724 .64 .025 361 .56 9 560 2 150 4 750 1 070 17 000 20 000 12 000
204-S 20 .7874 47 1.8504 14 .5512 1.0 .04 503 .78 12 700 2 860 6 550 1 470 15 000 18 000 10 000
205-S 25 .9843 52 2.0472 15 .5906 1.0 .04 568 .88 14 000 3 150 7 800 1 750 12 000 15 000 8 500
206-S 30 1.1811 62 2.4409 16 .6299 1.0 .04 819 1.27 19 500 4 380 11 200 2 520 10 000 13 000 7 500
207-S 35 1.3780 72 2.8346 17 .6693 1.0 .04 1 110 1.72 25 500 5 730 15 300 3 440 9 000 11 000 6 300
208-S 40 1.5748 80 3.1496 18 .7087 1.0 .04 1 360 2.11 30 700 6 900 19 000 4 270 8 500 10 000 5 600
209-S 45 1.7717 85 3.3465 19 .7480 1.0 .04 1 510 2.35 33 200 7 460 21 600 4 860 7 500 9 000 5 000
210-S 50 1.9685 90 3.5433 20 .7874 1.0 .04 1 610 2.50 35 100 7 890 23 200 5 220 7 000 8 500 4 800
211-S 55 2.1654 100 3.9370 21 .8268 1.5 .06 2 040 3.16 43 600 9 800 29 000 6 520 6 300 7 500 4 300
212-S 60 2.3622 110 4.3307 22 .8661 1.5 .06 2 280 3.53 47 500 10 700 32 500 7 310 6 000 7 000 4 000
213-S 65 2.5591 120 4.7244 23 .9055 1.5 .06 2 770 4.30 55 900 12 600 40 500 9 110 5 300 6 300 3 600
214-S 70 2.7559 125 4.9213 24 .9449 1.5 .06 3 060 5.18 60 500 13 600 45 000 10 100 5 000 6 000 3 400
215-S 75 2.9528 130 5.1181 25 .9843 1.5 .06 3 350 5.20 66 300 14 900 49 000 11 000 4 800 5 600 3 200
216-S 80 3.1496 140 5.5118 26 1.0236 2.0 .08 3 630 5.63 72 800 16 400 53 000 11 900 4 500 5 300 3 000
217-S 85 3.3465 150 5.9055 28 1.1024 2.0 .08 4 260 6.60 83 200 18 700 64 000 14 400 4 300 5 000 2 800
218-S 90 3.5433 160 6.2992 30 1.1811 2.0 .08 5 050 7.83 95 600 21 500 73 500 16 500 3 800 4 500 2 600
219-S 95 3.7402 170 6.6929 32 1.2598 2.0 .08 5 670 8.79 108 000 24 300 81 500 18 300 3 600 4 300 2 400
220-S 100 3.9370 180 7.0866 34 1.3386 2.0 .08 6 450 10.00 124 000 27 900 93 000 20 900 3 400 4 000 2 400
221-S 105 4.1339 190 7.4803 36 1.4173 2.0 .08 7 280 11.3 133 000 29 900 104 000 23 400 3 200 3 800 2 200
222-S 110 4.3307 200 7.8740 38 1.4961 2.0 .08 8 190 12.7 143 000 32 100 118 000 26 500 3 000 3 600 2 000
224-S 120 4.7244 215 8.4646 40 1.5748 2.0 .08 8 970 13.9 146 000 32 800 118 000 26 500 2 800 3 400 1 900
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2) Listed values are for pressed steel or polyamide cage, ABEC-1.
For phenolic composition cage, multiply by 1.66 for grease and 2.00 for oil. For machined bronze cage, multiply by 1.25 for grease and 1.50 for oil. For phenolic composition
cage, ABEC-5 or 7, multiply by 2.30 for grease and 2.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
48
300-S Medium Series
300-S 10 .3937 35 1.3780 11 .4331 .64 .025 303 .47 8 060 1 810 3 400 764 20 000 26 000 15 000
301-S 12 .4724 37 1.4567 12 .4724 1.0 .04 381 .59 9 750 2 190 4 150 933 19 000 24 000 14 000
302-S 15 .5906 42 1.6535 13 .5118 1.0 .04 439 .68 11 400 2 560 5 400 1 210 17 000 20 000 12 000
303-S 17 .6693 47 1.8504 14 .5512 1.0 .04 535 .83 13 500 3 030 6 550 1 470 16 000 19 000 11 000
304-S 20 .7874 52 2.0472 15 .5906 1.0 .04 632 .98 15 900 3 570 7 800 1 750 13 000 16 000 9 500
305-S 25 .9843 62 2.4409 17 .6693 1.0 .04 864 1.34 21 200 4 760 10 800 2 430 11 000 14 000 7 500
306-S 30 1.1811 72 2.8346 19 .7480 1.0 .04 1 210 1.88 28 100 6 320 16 000 3 600 9 000 11 000 6 300
307-S 35 1.3780 80 3.1496 21 .8268 1.5 .06 1 460 2.26 33 200 7 460 19 000 4 270 8 500 10 000 6 000
308-S 40 1.5748 90 3.5433 23 .9055 1.5 .06 1 820 2.82 41 000 9 220 24 000 5 400 7 500 9 000 5 000
309-S 45 1.7717 100 3.9370 25 .9843 1.5 .06 2 440 3.62 52 700 11 900 31 500 7 080 6 700 8 000 4 500
310-S 50 1.9685 110 4.3307 27 1.0630 2.0 .08 2 900 4.50 61 800 13 900 38 000 8 540 6 300 7 500 4 300
311-S 55 2.1654 120 4.7244 29 1.1417 2.0 .08 3 410 5.28 71 500 16 100 45 000 10 100 5 600 6 700 3 800
312-S 60 2.3622 130 5.1181 31 1.2205 2.0 .08 3 950 6.13 81 900 18 400 52 000 11 700 5 000 6 000 3 400
313-S 65 2.5591 140 5.5118 33 1.2992 2.0 .08 4 540 7.03 92 300 20 800 60 000 13 500 4 800 5 600 3 200
314-S 70 2.7559 150 5.9055 35 1.3780 2.0 .08 5 160 8.00 104 000 23 400 68 000 15 300 4 500 5 300 3 000
315-S 75 2.9528 160 6.2992 37 1.4567 2.0 .08 5 820 9.03 114 000 25 600 76 500 17 200 4 300 5 000 2 800
316-S 80 3.1496 170 6.6929 39 1.5354 2.0 .08 6 515 10.1 124 000 27 900 86 500 19 400 3 800 4 500 2 600
317-S 85 3.3465 180 7.0866 41 1.6142 2.5 .10 7 290 11.3 133 000 29 900 96 500 21 700 3 600 4 300 2 400
318-S 90 3.5433 190 7.4803 43 1.6929 2.5 .10 8 060 12.5 143 000 32 100 108 000 24 300 3 400 4 000 2 400
319-S 95 3.7402 200 7.8740 45 1.7717 2.5 .10 8 900 13.8 153 000 34 400 118 000 26 500 3 200 3 800 2 200
320-S 100 3.9370 215 8.4646 47 1.8504 2.5 .10 10 600 16.5 174 000 39 100 140 000 31 500 3 000 3 600 2 100
321-S 105 4.1339 225 8.8583 49 1.9291 2.5 .10 11 600 18.0 182 000 40 800 153 000 34 400 2 800 3 400 2 000
322-S 110 4.3307 240 9.4488 50 1.9685 2.5 .10 13 600 21.1 203 000 45 600 180 000 40 500 2 600 3 200 1 800
324-S 120 4.7244 260 10.2362 55 2.1654 2.5 .10 13 600 21.1 208 000 46 700 186 000 41 800 2 400 3 000 —
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2) Listed values are for pressed steel or polyamide cage, ABEC-1.
For phenolic composition cage, multiply by 1.66 for grease and 2.00 for oil. For machined bronze cage, multiply by 1.25 for grease and 1.50 for oil. For phenolic composition
cage, ABEC-5 or 7, multiply by 2.30 for grease and 2.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
49
400-S Heavy Series MRC Bearing Services
403-S 17 .6693 62 2.4409 17 .6693 1.0 .04 968 1.50 22 900 5 150 10 800 2 430 12 000 15 000 8 500
404-S 20 .7874 72 2.8346 19 .7480 1.0 .04 1 370 2.12 30 700 6 900 15 000 3 370 10 000 13 000 7 300
405-S 25 .9843 80 3.1496 21 .8268 1.5 .06 1 590 2.47 35 800 8 050 19 300 4 340 9 000 11 000 6 400
406-S 30 1.1811 90 3.5433 23 .9055 1.5 .06 1 950 3.02 43 600 9 800 23 600 5 310 8 500 10 000 5 600
407-S 35 1.3780 100 3.9370 25 .9843 1.5 .06 2 540 3.94 55 300 12 400 31 000 6 970 7 000 8 500 4 900
408-S 40 1.5748 110 4.3307 27 1.0630 2.0 .08 2 980 4.62 63 700 14 300 36 500 8 210 6 700 8 000 4 400
409-S 45 1.7717 120 4.7244 29 1.1417 2.0 .08 3 710 5.75 76 100 17 100 45 000 10 100 6 000 7 000 4 000
410-S 50 1.9685 130 5.1181 31 1.2205 2.0 .08 4 520 7.00 87 100 19 600 52 000 11 700 5 200 6 300 3 700
411-S 55 2.1654 140 5.5118 33 1.2992 2.0 .08 5 100 7.90 99 500 22 400 62 000 13 900 5 000 6 000 3 400
412-S 60 2.3622 150 5.9055 35 1.3780 2.0 .08 5 710 8.86 108 000 24 300 69 500 15 600 4 800 5 600 3 100
413-S 65 2.5591 160 6.2992 37 1.4567 2.0 .08 6 370 9.87 119 000 26 800 78 000 17 500 4 500 5 300 2 900
414-S 70 2.7559 180 7.0866 42 1.6535 2.5 .10 8 510 13.2 143 000 32 100 104 000 23 400 3 800 4 500 2 600
415-S 75 2.9528 190 7.4803 45 1.7717 2.5 .10 9 350 14.5 153 000 34 400 114 000 25 600 3 600 4 300 2 500
416-S 80 3.1496 200 7.8740 48 1.8898 2.5 .10 10 200 15.8 163 000 36 600 125 000 28 100 3 400 4 000 2 300
417-S 85 3.3465 210 8.2677 52 2.0472 3.0 .12 11 000 17.1 174 000 39 100 137 000 30 800 3 200 3 800 2 200
418-S 90 3.5433 225 8.8583 54 2.1260 3.0 .12 12 800 19.9 186 000 41 800 150 000 33 700 3 000 3 600 2 100
419-S4) 95 3.7402 250 9.8425 55 2.1654 3.0 .12 13 800 21.4 203 000 45 600 173 000 38 900 2 700 3 300 1 900
420-S4) 100 3.9370 265 10.4331 60 2.3622 3.0 .12 15 900 24.6 225 000 50 600 200 000 45 000 2 500 3 100 1 800
421-S4) 105 4.1339 290 11.4173 65 2.5591 3.0 .12 18 100 28.0 247 000 55 500 228 000 51 300 2 400 2 900 1 600
422-S4) 110 4.3307 320 12.5984 70 2.7559 3.0 .12 20 300 31.6 270 000 60 700 260 000 58 500 2 100 2 600 1 500
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
Listed values are for pressed steel or polyamide cage, ABEC-1.
For phenolic composition cage, multiply by 1.66 for grease and 2.00 for oil. For machined bronze cage, multiply by 1.25 for grease and 1.50 for oil. For phenolic composition
cage, ABEC-5 or 7, multiply by 2.30 for grease and 2.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
4) Typically non-stocked sizes, please check availability before designing into equipment.
50
Cartridge-Type Bearings Types
SFFC, SZZC, SLLC
200-SFFC 10 .3937 30 1.1811 14.29 ⁹|₁₆ .64 .025 181 .28 5 070 1 140 2 400 540 24 000 30 000 17 000
201-SFFC 12 .4724 32 1.2598 15.88 ⁵|₈ .64 .025 252 .39 6 760 1 520 3 000 674 22 000 28 000 15 000
202-SFFC 15 .5906 35 1.3780 15.88 ⁵|₈ .64 .025 290 .45 7 610 1 710 3 750 843 19 000 24 000 13 000
203-SFFC 17 .6693 40 1.5748 17.46 ¹¹|₁₆ .64 .025 361 .56 9 560 2 150 4 500 1 010 17 000 20 000 12 000
204-SFFC 20 .7874 47 1.8504 20.64 ¹³|₁₆ 1.0 .04 503 .78 13 000 2 920 6 700 1 510 15 000 18 000 10 000
205-SFFC 25 .9843 52 2.0472 20.64 ¹³|₁₆ 1.0 .04 568 .88 15 100 3 390 8 150 1 830 12 000 15 000 8 500
206-SFFC 30 1.1811 62 2.4409 23.81 ¹⁵|₁₆ 1.0 .04 819 1.27 20 800 4 680 11 400 2 560 10 000 13 000 7 500
207-SFFC 35 1.3780 72 2.8346 26.99 1¹|₁₆ 1.0 .04 1 140 1.76 26 500 5 960 15 300 3 440 9 000 11 000 6 300
208-SFFC 40 1.5748 80 3.1496 30.16 1³|₁₆ 1.0 .04 1 450 2.25 32 500 7 310 20 000 4 550 8 500 10 000 5 600
209-SFFC 45 1.7717 85 3.3465 30.16 1³|₁₆ 1.0 .04 1 640 2.54 36 400 8 180 22 800 5 130 7 500 9 000 5 000
210-SFFC 50 1.9685 90 3.5433 30.16 1³|₁₆ 1.0 .04 1 610 2.50 35 100 7 890 23 200 5 220 7 000 8 500 4 800
211-SFFC 55 2.1654 100 3.9370 33.34 1⁵|₁₆ 1.5 .06 2 040 3.16 39 700 8 920 29 000 6 520 6 300 7 500 4 300
213-SFFC 65 2.5591 120 4.7244 38.10 1¹|₂ 1.5 .06 3 050 4.73 62 400 14 000 44 000 9 890 5 300 6 300 3 600
214-SFFC 70 2.7559 125 4.9213 39.69 1⁹|₁₆ 1.5 .06 3 050 4.73 62 400 14 000 44 000 9 890 5 000 6 000 3 400
216-SFFC 80 3.1496 140 5.5118 44.45 1³|₄ 2.0 .08 3 630 5.63 78 000 17 500 53 000 11 900 4 500 5 300 3 000
304-SFFC 20 .7874 52 2.0472 22.23 ⁷|₈ 1.0 .04 632 .98 15 900 3 570 7 800 1 750 13 000 16 000 9 500
305-SFFC 25 .9843 62 2.4409 25.40 1 1.0 .04 864 1.34 21 000 4 770 11 000 2 470 11 000 14 000 7 500
306-SFFC 30 1.1811 72 2.8346 30.16 1³|₁₆ 1.0 .04 1 290 2.00 29 600 6 650 16 600 3 730 9 000 11 000 6 300
307-SFFC 35 1.3780 80 3.1496 34.93 1³|₈ 1.5 .06 1 590 2.47 36 400 8 180 20 000 4 500 8 500 10 000 6 000
308-SFFC 40 1.5748 90 3.5433 36.51 1⁷|₁₆ 1.5 .06 2 020 3.13 44 200 9 940 26 000 5 850 7 500 9 000 5 000
309-SFFC 45 1.7717 100 3.9370 39.69 1⁹|₁₆ 1.5 .06 2 330 3.62 52 000 11 700 30 000 6 740 6 700 8 000 4 500
310-SFFC 50 1.9685 110 4.3307 44.45 1³|₄ 2.0 .08 2 900 4.50 61 800 13 900 38 000 8 540 6 300 7 500 4 300
311-SFFC 55 2.1654 120 4.7244 49.21 1¹⁵|₁₆ 2.0 .08 3 410 5.28 71 500 16 100 45 000 10 100 5 600 6 700 3 800
312-SFFC 60 2.3622 130 5.1181 53.98 2¹|₈ 2.0 .08 3 950 6.13 81 900 18 400 52 000 11 700 5 000 6 000 3 400
313-SFFC 65 2.5591 140 5.5118 58.74 2⁵|₁₆ 2.0 .08 4 530 7.03 92 300 20 700 60 000 13 500 4 800 5 600 3 200
314-SFFC 70 2.7559 150 5.9055 63.50 2¹|₂ 2.0 .08 5 160 8.00 104 000 23 400 68 000 15 300 4 500 5 300 3 000
315-SFFC 75 2.9528 160 6.2992 68.26 2¹¹|₁₆ 2.0 .08 6 530 10.1 124 000 27 900 85 000 19 100 4 300 5 000 2 800
316-SFFC 80 3.1496 170 6.6929 68.26 2¹¹|₁₆ 2.0 .08 7 280 11.3 133 000 29 900 95 000 21 400 3 800 4 500 2 600
317-SFFC 85 3.3465 180 7.0866 73.03 2⁷|₈ 2.5 .10 7 280 11.3 133 000 29 900 96 500 21 700 3 600 4 300 2 400
318-SFFC 90 3.5433 190 7.4803 73.03 2⁷|₈ 2.5 .10 8 060 12.5 143 000 32 100 108 000 24 300 3 400 4 000 2 400
320-SFFC 100 3.9370 215 8.4646 82.55 3¹|₄ 2.5 .10 11 600 18.0 182 000 40 900 150 000 33 700 3 000 3 600 2 100
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2) Listed values are for pressed steel or polyamide cage, ABEC-1.
The values have been determined through historical application and practice. For a more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
51
Single-Row Deep Groove
Ball Bearings, S-Type MRC Bearing Services
FR = Radial load or
FA = Thrust load 6 3
Z = Number of balls
D = Ball diameter
L10h =
10 C
60n P
() (Hours)
52
Single Row Deep Groove
Ball Bearings, S-Type
Case 1 Case 1
Radial load (FR) = 1890 Radial load (FR) = 1890
Equivalent load (P) = X FR + Y FA Equivalent load (P) = X FR + YA
P = FR = 1890 3 3
P = FR = 1890 3 3
11900 11900
()
Life (L10) = C =
P 1890( )
= 249.6 × 106 Rev. Life (L10) = C =
P() 1890 ( )
= 249.6 × 106 Rev.
or 6 3 6 3
or 6 3 6 3
11900 11900
Life (L10h) =
10 C
60n P ()
=
10
60 × 2000 1890
( ) Life (L10h) =
10 C
60n P ()=
10
60 × 2000 1890
( )
= 2080 Hrs = 2080 Hrs
Case 2 Case 2
Radial load (FR) = 1890 Radial load (FR) = 1890
Thrust load (FA) = 1250 Thrust load (FA) = 1250
Equivalent load (P) = X FR + Y FA Equivalent load (P) = X FR + Y FA
FA/ZD2 = 1250/3.62 = 345 FA/ZD2 = 1250/3.62 = 345
X = 0.56 X = 0.44
Y = 1.27 Y = 1.08
P = 0.56 × 1890 + 1.27 × 1250 = 2646 P = 0.44 × 1890 + 1.08 × 1250 = 2182
3 3 3 3
Life (L10) = (CP) = (11900
2646 )
= 91.0 × 106 Rev. Life (L10) = (CP) = (11900
2182 )
= 162.2 × 106 Rev.
or 6 3 6 3 or 6 3 6 3
11900 11900
Life (L10h) =
10 C
60n P
()
=
10
60 × 2000 2646
( ) Life (L10h) =
10 C
60n P
()
=
10
60 × 2000 2182
( )
= 758 Hrs = 1352Hrs
Case 3 Case 3
Thrust load (FA) = 1250 Thrust load (FA) = 1250
Equivalent load (P) = X FR + Y FA Equivalent load (P) = X FR + Y FA
FA/ZD2 = 1250/3.62 = 345 FA/ZD2 = 1250/3.62 = 345
Y = 1.27 Y = 1.08
P = 1.27 × 1250 = 1588 P = 1.08 × 1250 = 1350
3 3 3 3
11900 11900
Life (L10) = ()
C
P
=
1588( )
= 420.8 × 106 Rev. Life (L10) =
C
P() =
1350 ( )
= 684.9 × 106 Rev.
or 6 3 6 3 or 6 3 6 3
11900 11900
Life (L10h) =
10 C
60n P
()
=
10
60 × 2000 1588
( ) Life (L10h) =
10 C
60n P
()
=
10
60 × 2000 1350
( )
= 3507 Hrs = 5708 Hrs
53
Hybrid Ceramic Ball Bearings MRC Bearing Services
100KS
200S
306S-HYB#1 30 72 19 1 6,700 3,200 14,300 0.328 0.72
Sealing Options
307S-HYB#1 35 80 21 1.5 7,900 3,800 13,200 0.422 0.93
54
Hybrid Ceramic Ball Bearings
Mechanical properties
Electrical properties
Electrical resistivity [Wm] 0.4 x 10-6 1012 (insulator) The ceramic balls break the electrical
(conductor) current (DC) path and act as an
insulator
Relative dielectric constant N/A 4.2 to 6.1 The ceramic balls break the electrical
current (AC) path and act as a large
impedance
56
“Max-Type” (M-Type)
Single-Row Filling-Notch Ball Bearings
MRC’s single-row Maximum “M-type” bearings have Cage Types and Materials
a single filling slot in both the inner and outer ring,
enabling more balls to be added. Because of the Type and material available is a two-piece, pressed
increased ball compliment, filling slot bearings have steel, ball riding, stayrod cage.
a higher radial load carrying capacity than bearings
without filling slots, but their axial load carrying capacity
is reduced. They can be used in applications with
heavy radial loads, or a combination of radial and thrust
loads, where the radial load is predominant. They are
not recommended for use where only thrust loads are
present.
57
100-M Narrow-Type Light Series MRC Bearing Services
MF NOTE: This series is obsoleted but is still manufactured in a few sizes for
One Shield replacement parts, please check availability before designing into equipment.
Basic Radial Load Rating Speed Rating2)
MRC Bore Outside Width Fillet
Bearing Diameter Radius1) Dynamic Static Open and Shielded
Number d D B ra C3) C0 Grease Oil
mm in mm in mm in mm in N lbf N lbf RPM RPM
110-M4)
50 1.9685 90 3.5433 11 .4331 1.0 .04 18 700 4 200 19 600 4 400 5 600 6 800
113-M4) 65 2.5591 115 4.5276 14 .5512 1.0 .04 31 900 7 170 36 500 8 210 4 400 5 400
117-M4) 85 3.3465 145 5.7087 18 .7087 1.5 .06 58 300 13 100 68 000 15 300 3 400 4 200
120-M 100 3.9370 160 6.2992 28 1.1024 2.0 .08 96 800 21 800 108 000 24 300 3 000 3 700
124-M 120 4.7244 190 7.4803 32 1.2598 2.0 .08 123 000 27 700 146 000 32 800 2 500 3 100
126-M 130 5.1181 205 8.0709 34 1.3386 2.0 .08 138 000 31 000 166 000 37 300 2 300 2 800
128-M 140 5.5118 220 8.6614 36 1.4173 2.0 .08 157 000 35 300 190 000 42 800 2 100 2 600
132-M 160 6.2992 250 9.8425 40 1.5748 2.0 .08 190 000 42 700 255 000 57 300 1 900 2 300
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
Listed values are for pressed steel or polyamide cage, ABEC-1.
The values have been determined through historical application and practice. For a more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
4) Typically non-stocked sizes, please check availability before designing into equipment.
58
200-M Light Series
202-M4)
15 .5906 35 1.3780 11 .4331 .64 .025 8 250 1 850 5 100 1 150 16 000 20 000
203-M4) 17 .6693 40 1.5748 12 .4724 .64 .025 8 970 2 020 6 000 1 350 14 000 17 000
204-M4) 20 .7874 47 1.8504 14 .5512 1.0 .04 12 500 2 810 8 300 1 870 12 000 15 000
205-M4) 25 .9843 52 2.0472 15 .5906 1.0 .04 16 100 3 620 11 200 2 510 11 000 13 000
206-M 30 1.1811 62 2.4409 16 .6299 1.0 .04 22 900 5 150 17 000 3 820 9 000 11 000
207-M 35 1.3780 72 2.8346 17 .6693 1.0 .04 29 700 6 680 22 800 5 130 7 800 9 500
208-M 40 1.5748 80 3.1496 18 .7087 1.0 .04 33 600 7 550 26 500 5 960 7 000 8 500
209-M 45 1.7717 85 3.3465 19 .7480 1.0 .04 39 300 8 840 32 500 7 310 6 200 7 500
210-M 50 1.9685 90 3.5433 20 .7874 1.0 .04 39 100 8 790 34 500 7 760 5 700 7 000
211-M 55 2.1654 100 3.9370 21 .8268 1.5 .06 48 400 10 900 44 000 9 890 5 200 6 300
212-M 60 2.3622 110 4.3307 22 .8661 1.5 .06 56 100 12 600 51 000 11 500 4 900 6 000
213-M 65 2.5591 120 4.7244 23 .9055 1.5 .06 69 300 15 600 65 500 14 700 4 300 5 300
214-M 70 2.7559 125 4.9213 24 .9449 1.5 .06 69 300 15 600 65 500 14 700 4 100 5 000
215-M 75 2.9528 130 5.1181 25 .9843 1.5 .06 74 800 16 800 72 000 16 200 3 900 4 800
216-M 80 3.1496 140 5.5118 26 1.0236 2.0 .08 85 800 19 300 86 500 19 400 3 700 4 500
217-M 85 3.3465 150 5.9055 28 1.1024 2.0 .08 88 000 19 800 93 000 20 900 3 500 4 300
218-M 90 3.5433 160 6.2992 30 1.1811 2.0 .08 101 000 22 700 108 000 24 300 3 300 4 000
219-M 95 3.7482 170 6.6929 32 1.2598 2.0 .08 111 000 25 000 118 000 26 500 3 100 3 800
220-M 100 3.9370 180 7.0866 34 1.3386 2.0 .08 127 000 28 600 134 000 30 100 2 800 3 400
221-M 105 4.1339 190 7.4803 36 1.4173 2.0 .08 142 000 31 900 153 000 34 400 2 600 3 200
222-M 110 4.3307 200 7.8740 38 1.4961 2.0 .08 154 000 34 600 170 000 38 200 2 500 3 100
224-M 120 4.7244 215 8.4646 40 1.5748 2.0 .08 172 000 38 700 200 000 45 000 2 300 2 800
226-M 130 5.1181 230 9.0551 40 1.5748 2.5 .10 179 000 40 300 216 000 48 500 2 100 2 600
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
Listed values are for pressed steel or polyamide cage, ABEC-1.
The values have been determined through historical application and practice. For a more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
4) Typically non-stocked sizes, please check availability before designing into equipment.
59
300-M Medium Series MRC Bearing Services
303-M 17 .6693 47 1.8504 14 .5512 1.0 .04 14 200 3 200 8 500 1 910 12 000 15 000
304-M 20 .7874 52 2.0472 15 .5906 1.0 .04 15 900 3 570 10 200 2 280 11 000 14 000
305-M 25 .9843 62 2.4409 17 .6693 1.0 .04 22 900 5 150 15 600 3 510 9 800 12 000
306-M 30 1.1811 72 2.8346 19 .7480 1.0 .04 29 200 6 560 20 800 4 680 7 800 9 500
307-M 35 1.3780 80 3.1496 21 .8268 1.5 .06 39 300 8 830 28 500 6 410 7 000 8 500
308-M 40 1.5748 90 3.5433 23 .9055 1.5 .06 46 800 10 500 36 000 8 090 6 200 7 500
309-M 45 1.7717 100 3.9370 25 .9843 1.5 .06 59 400 13 400 46 500 10 500 5 700 7 000
310-M 50 1.9685 110 4.3307 27 1.0630 2.0 .08 64 400 14 500 52 000 11 700 5 200 6 300
311-M 55 2.1654 120 4.7244 29 1.1417 2.0 .08 79 200 17 800 65 500 14 700 4 600 5 600
312-M 60 2.3622 130 5.1181 31 1.2205 2.0 .08 91 300 20 500 78 000 17 500 4 300 5 300
313-M 65 2.5591 140 5.5118 33 1.2992 2.0 .08 102 000 22 900 90 000 20 200 3 900 4 800
314-M 70 2.7559 150 5.9055 35 1.3780 2.0 .08 114 000 25 600 102 000 22 900 3 700 4 500
315-M 75 2.9528 160 6.2992 37 1.4567 2.0 .08 125 000 28 000 116 000 26 000 3 500 4 300
316-M 80 3.1496 170 6.6929 39 1.5354 2.0 .08 138 000 31 000 129 000 29 000 3 300 4 000
317-M 85 3.3465 180 7.0866 41 1.6142 2.5 .10 147 000 33 000 146 000 32 800 3 100 3 800
318-M 90 3.5433 190 7.4803 43 1.6929 2.5 .10 157 000 35 300 160 000 36 000 2 800 3 400
319-M 95 3.7402 200 7.8740 45 1.7717 2.5 .10 168 000 37 800 180 000 40 500 2 600 3 200
320-M 100 3.9370 215 8.4646 47 1.8504 2.5 .10 194 000 43 600 212 000 47 700 2 500 3 000
321-M 105 4.1339 225 8.8583 49 1.9291 2.5 .10 205 000 46 100 232 000 52 200 2 400 2 900
322-M 110 4.3307 240 9.4488 50 1.9685 2.5 .10 216 000 48 600 250 000 56 200 2 200 2 700
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2) Listed values are for pressed steel or polyamide cage, ABEC-1.
The values have been determined through historical application and practice. For a more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
60
400-M Heavy Series
403-M 17 .6693 62 2.4409 17 .6693 1.0 .04 23 300 5 240 14 600 3 280 11 000 13 000
404-M 20 .7874 72 2.8346 19 .7480 1.0 .04 29 200 6 560 18 600 4 210 9 000 11 000
405-M 25 .9843 80 3.1496 21 .8268 1.5 .06 35 800 8 050 23 600 5 270 7 700 9 400
406-M 30 1.1811 90 3.5433 23 .9055 1.5 .06 45 700 10 300 32 500 7 310 6 200 7 500
407-M 35 1.3780 100 3.9370 25 .9843 1.5 .06 53 900 12 100 39 000 8 770 5 600 6 800
408-M 40 1.5748 110 4.3307 27 1.0630 2.0 .08 68 200 15 300 52 000 11 700 5 300 6 500
409-M 45 1.7717 120 4.7244 29 1.1417 2.0 .08 78 100 17 600 61 000 13 700 4 800 5 900
410-M 50 1.9685 130 5.1181 31 1.2205 2.0 .08 88 000 19 800 71 000 16 000 4 400 5 400
411-M 55 2.1654 140 5.5118 33 1.2992 2.0 .08 108 000 24 200 90 000 20 200 4 100 5 000
412-M 60 2.3622 150 5.9055 35 1.3780 2.0 .08 117 000 26 200 102 000 22 900 3 800 4 600
413-M 65 2.5591 160 6.2992 37 1.4567 2.0 .08 128 000 28 800 112 000 25 200 3 400 4 100
414-M 70 2.7559 180 7.0866 42 1.6535 2.5 .10 147 000 33 100 140 000 31 500 3 200 3 900
415-M 75 2.9528 190 7.4803 45 1.7717 2.5 .10 157 000 55 300 153 000 34 400 3 000 3 600
416-M 80 3.1496 200 7.8740 48 1.8898 2.5 .10 176 000 89 600 176 000 39 600 2 800 3 400
417-M 85 3.3465 210 8.2677 52 2.0472 3.0 .12 190 000 42 700 200 000 45 000 2 600 3 200
418-M 90 3.5433 225 8.8583 54 2.1260 3.0 .12 198 000 44 500 212 000 47 700 2 500 3 000
419-M 95 3.7402 250 9.8425 55 2.1654 3.0 .12 229 000 51 500 260 000 58 500 2 300 2 800
420-M 100 3.9370 265 10.4331 60 2.3622 3.0 .12 251 000 56 500 300 000 67 400 2 100 2 600
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
Listed values are for pressed steel or polyamide cage, ABEC-1.
The values have been determined through historical application and practice. For a more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
61
Single-Row
Filling-Notch Ball Bearings, M-Type MRC Bearing Services
FR = Radial load or
FA = Thrust load 6 3
62
Single-Row
Filling-Notch Ball Bearings, M-Type
Case 1
Radial load (FR) = 1890
Equivalent load (P) = FR + FA
P = FR = 1890 3 3
13400
Life (L10) = C =
P() 1890 ( )
= 356 × 106 Rev.
or 6 3 6 3
13400
Life (L10h) =
10 C
60n P ()=
10
60 × 2000 1890
( )
= 2967 Hrs
Case 2
Radial load (FR) = 1890
Thrust load (FA) = 950
or 3 3
6 6
10 13400 13400
Life (L10h) =
60n
( 2840
= )
10
60 × 2000 2840
( )
= 875 Hrs
Case 3
Radial load (FR) = 1890
Thrust load (FA) = 1250
FA /FR = 1250/1890 = 0.66
63
64
Self-Aligning Ball Bearings
Self-aligning bearings have two rows of balls with a Bearing sizes having the E suffix have higher load
common sphered raceway in the outer ring. This gives ratings than the original standard design because
the bearings their self-aligning property, permitting of improvements in internal construction. They are
angular misalignment of the shaft relative to the housing. supplied with a glass fiber reinforced, 6.6 polyamide
They are therefore particularly suitable for applications cage as standard. Machined brass or pressed steel
where misalignment can arise from errors in mounting or cages are supplied on other sizes.
from shaft deflection. In addiiton, non-sealed self-aligning
ball bearings have the lowest friction of any bearing type.
Series Page
100 67
1200, 1200E 67
1300, 1300E 68
1400 68
2200, 2200E 69
2300, 2300E 69
1200K, 1200EK—Tapered Bore 70
1300K, 1300EK—Tapered Bore 70
2200K, 2200EK—Tapered Bore 71
2300K, 2300EK—Tapered Bore 71
1200K, 1200EK—Tapered Bore with Adapter Sleeve 72
1300K, 1300EK—Tapered Bore with Adapter Sleeve 72
2200K, 2200EK—Tapered Bore with Adapter Sleeve 73
2300K, 2300EK—Tapered Bore with Adapter Sleeve 73
2200E2RS1—Two Seals 74
2300E2RS1—Two Seals 74
2200E2RS1K—Two Seals and Tapered Bore 74
11200E—Extended Inner Ring 75
11300E—Extended Inner Ring 75
Internal Clearance 76
Allowable Angular Misalignment 76
Equivalent Load and Life 77
Life Calculation Examples 77
Minimum Required Radial Load 77
Ball Protrusion Beyond Bearing Face 79
Mounting Procedure 80
65
Self-Aligning Ball Bearings MRC Bearing Services
Tolerances
to smooth or stepped shafts. They are identified by
suffix letter K.
66
Self-Aligning Ball Bearings
100, 1200, 1200-E Series
135 5 .1969 19 .7480 6 .2362 .30 .012 .33 1.9 3 2 2 510 564 480 108 32 000 38 000
126 6 .2362 19 .7480 6 .2362 .30 .012 .33 1.9 3 2 2 510 564 480 108 32 000 38 000
127 7 .2756 22 .8661 7 .2756 .30 .012 .33 1.9 3 2 2 650 596 560 126 30 000 36 000
108 8 .3150 22 .8661 7 .2756 .30 .012 .33 1.9 3 2 2 650 596 560 126 30 000 36 000
129 9 .3543 26 1.0236 8 .3150 .60 .024 .33 1.9 3 2 3 900 877 815 183 26 000 32 000
1200E 10 .3937 30 1.1811 9 .3543 .60 .024 .33 1.9 3 2 5 530 1 240 1 180 265 24 000 30 000
1201E 12 .4724 32 1.2598 10 .3937 .60 .024 .33 1.9 3 2 6 240 1 400 1 430 321 22 000 28 000
1202E 15 .5906 35 1.3780 11 .4331 .60 .024 .33 1.9 3 2 7 410 1 670 1 760 396 19 000 24 000
1203E 17 .6693 40 1.5748 12 .4724 .60 .024 .31 2 3.1 2.2 8 840 1 990 2 200 495 18 000 22 000
1204E 20 .7874 47 1.8504 14 .5512 1.0 .039 .30 2.1 3.3 2.2 12 700 2 860 3 400 764 15 000 18 000
1205E 25 .9843 52 2.0472 15 .5906 1.0 .039 .28 2.2 3.5 2.5 14 300 3 220 4 000 899 13 000 16 000
1206E 30 1.1811 62 2.4409 16 .6299 1.0 .039 .25 2.5 3.9 2.5 15 600 3 510 4 650 1 050 10 000 13 000
1207E 35 1.3780 72 2.8346 17 .6693 1.0 .039 .23 2.7 4.2 2.8 19 000 4 270 6 000 1 350 9 000 11 000
1208E 40 1.5748 80 3.1496 18 .7087 1.0 .039 .22 2.9 4.5 2.8 19 900 4 470 6 950 1 560 8 500 10 000
1209E 45 1.7717 85 3.3465 19 .7480 1.0 .039 .21 3 4.6 3.2 22 900 5 150 7 800 1 750 7 500 9 000
1210E 50 1.9685 90 3.5433 20 .7874 1.0 .039 .21 3 4.6 3.2 26 500 5 960 9 150 2 060 7 000 8 500
1211E 55 2.1654 100 3.9370 21 .8268 1.5 .059 .19 3.3 5.1 3.6 27 600 6 210 10 600 2 380 6 300 7 500
1212E 60 2.3622 110 4.3307 22 .8661 1.5 .059 .19 3.3 5.1 3.6 31 200 7 010 12 200 2 740 5 600 6 700
1213E 65 2.5591 120 4.7244 23 .9055 1.5 .059 .18 3.5 5.4 3.6 35 100 7 890 14 000 3 150 5 300 6 300
1214 70 2.7559 125 4.9213 24 .9449 1.5 .059 .18 3.5 5.4 3.6 34 500 7 760 13 700 3 080 5 000 6 000
1215 75 2.9528 130 5.1181 25 .9843 1.5 .059 .17 3.7 5.7 4 39 000 8 770 15 600 3 510 4 800 5 600
1216 80 3.1496 140 5.5118 26 1.0236 2.0 .079 .16 3.9 6.1 4 39 700 8 930 17 000 3 820 4 500 5 300
1217 85 3.3465 150 5.9055 28 1.1024 2.0 .079 .17 3.7 5.7 4 48 800 11 000 20 800 4 680 4 000 4 800
1218 90 3.5433 160 6.2992 30 1.1811 2.0 .079 .17 3.7 5.7 4 57 200 12 900 23 600 5 310 3 800 4 500
1219 95 3.7402 170 6.6929 32 1.2598 2.0 .079 .17 3.7 5.7 4 63 700 14 300 27 000 6 070 3 600 4 300
1220 100 3.9370 180 7.0866 34 1.3386 2.0 .079 .17 3.7 5.7 4 68 900 15 500 30 000 6 740 3 400 4 000
1221 105 4.1339 190 7.4803 36 1.4173 2.0 .079 .17 3.7 5.7 4 74 100 16 700 32 500 7 310 3 200 3 800
1222 110 4.3307 200 7.8740 38 1.4961 2.0 .079 .17 3.7 5.7 4 88 400 19 900 39 000 8 770 3 000 3 600
1224 120 4.7244 215 8.4646 42 1.6535 2.0 .079 .19 3.3 5.1 3.6 119 000 26 800 53 000 11 900 2 800 3 400
1226 130 5.1181 230 9.0551 46 1.8110 2.5 .098 .19 3.3 5.1 3.6 127 000 28 600 58 500 13 200 2 600 3 200
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
67
1300, 1300-E, 1400 Series
Self-Aligning Ball Bearings MRC Bearing Services
1301E 12 .4724 37 1.4567 12 .4724 1.0 .039 .35 1.8 2.8 1.8 9 360 2 100 2 160 486 18 000 22 000
1302E 15 .5906 42 1.6535 13 .5118 1.0 .039 .31 2 3.1 2.2 10 800 2 430 2 600 585 17 000 20 000
1303E 17 .6693 47 1.8504 14 .5512 1.0 .039 .30 2.1 3.3 2.2 12 700 2 860 3 400 764 14 000 17 000
1304E 20 .7874 52 2.0472 15 .5906 1.0 .039 .28 2.2 3.5 2.5 14 300 3 220 4 000 899 12 000 15 000
1305E 25 .9843 62 2.4409 17 .6693 1.0 .039 .28 2.2 3.5 2.5 19 000 4 270 5 400 1 210 9 500 12 000
1306E 30 1.1811 72 2.8346 19 .7480 1.0 .039 .25 2.5 3.9 2.5 22 500 5 060 6 800 1 530 9 000 11 000
1307E 35 1.3780 80 3.1496 21 .8268 1.5 .059 .25 2.5 3.9 2.5 26 500 5 960 8 500 1 910 7 500 9 000
1308E 40 1.5748 90 3.5433 23 .9055 1.5 .059 .23 2.7 4.2 2.8 33 800 7 600 11 200 2 520 6 700 8 000
1309E 45 1.7717 100 3.9370 25 .9843 1.5 .059 .23 2.7 4.2 2.8 39 000 8 770 13 400 3 010 6 300 7 500
1310E 50 1.9685 110 4.3307 27 1.0630 2.0 .079 .24 2.6 4.1 2.8 43 600 9 800 14 000 3 150 5 600 6 700
1311E 55 2.1654 120 4.7244 29 1.1417 2.0 .079 .23 2.7 4.2 2.8 50 700 11 400 18 000 4 050 5 000 6 000
1312E 60 2.3622 130 5.1181 31 1.2205 2.0 .079 .23 2.7 4.2 2.8 58 500 13 200 22 000 4 950 4 500 5 300
1313E 65 2.5591 140 5.5118 33 1.2992 2.0 .079 .22 2.9 4.5 2.8 65 000 14 600 25 500 5 730 4 300 5 000
1314 70 2.7559 150 5.9055 35 1.3780 2.0 .079 .22 2.9 4.5 2.8 74 100 16 700 27 500 6 180 4 000 4 800
1315 75 2.9528 160 6.2992 37 1.4567 2.0 .079 .22 2.9 4.5 2.8 79 300 17 800 30 000 6 740 3 800 4 500
1316 80 3.1496 170 6.6929 39 1.5354 2.0 .079 .22 2.9 4.5 2.8 88 400 19 900 33 500 7 530 3 600 4 300
1317 85 3.3465 180 7.0866 41 1.6142 2.5 .098 .22 2.9 4.5 2.8 97 500 21 900 38 000 8 540 3 400 4 000
1318 90 3.5433 190 7.4803 43 1.6929 2.5 .098 .22 2.9 4.5 2.8 117 000 26 300 44 000 9 890 3 200 3 800
1319 95 3.7402 200 7.8740 45 1.7717 2.5 .098 .23 2.7 4.2 2.8 133 000 29 900 51 000 11 500 3 000 3 600
1320 100 3.9370 215 8.4646 47 1.8504 2.5 .098 .23 2.7 4.2 2.8 143 000 32 200 57 000 12 800 2 800 3 400
1322 110 4.3307 240 9.4488 50 1.9685 2.5 .098 .22 2.9 4.5 2.8 163 000 36 600 72 000 16 200 2 400 3 000
1406 30 1.1811 90 3.5433 28 1.1024 1.5 .059 .40 1.6 2.4 1.6 59 200 13 300 17 000 3 820 6 700 8 000
1407 35 1.3780 100 3.9370 30 1.1811 1.5 .059 .37 1.7 2.6 1.8 62 400 14 000 18 000 4 050 6 300 7 500
1408 40 1.5748 110 4.3307 33 1.2992 2.0 .079 .35 1.8 2.8 1.8 76 100 17 100 23 600 5 310 5 300 6 300
1409 45 1.7717 120 4.7244 35 1.3780 2.0 .079 .35 1.8 2.8 1.8 88 400 19 900 27 500 6 180 5 000 6 000
1410 50 1.9685 130 5.1181 37 1.4567 2.0 .079 .35 1.8 2.8 1.8 101 000 22 700 32 000 7 190 4 800 5 600
1411 55 2.1654 140 5.5118 40 1.5748 2.0 .079 .33 1.9 3 2 111 000 25 000 36 500 8 210 4 300 5 000
1412 60 2.3622 150 5.9055 42 1.6535 2.0 .079 .33 1.9 3 2 125 000 28 100 41 500 9 330 3 800 4 500
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
68
2200, 2200-E, 2300, 2300-E Series
Self-Aligning Ball Bearing
2200E 10 .3937 30 1.1811 14 .5512 .60 .024 .54 1.15 1.8 1.3 8 060 1 810 1 730 389 22 000 28 000
2201E 12 .4724 32 1.2598 14 .5512 .60 .024 .50 1.25 2 1.3 8 520 1 920 1 900 427 20 000 26 000
2202E 15 .5906 35 1.3780 14 .5512 .60 .024 .43 1.5 2.3 1.6 8 710 1 960 2 040 459 18 000 22 000
2203E 17 .6693 40 1.5748 16 .6299 .60 .024 .43 1.5 2.3 1.6 10 600 2 380 2 550 573 17 000 20 000
2204E 20 .7874 47 1.8504 18 .7087 1.0 .039 .40 1.6 2.4 1.6 16 800 3 780 4 150 933 14 000 17 000
2205E 25 .9843 52 2.0472 18 .7087 1.0 .039 .35 1.8 2.8 1.8 16 800 3 780 4 400 989 11 000 14 000
2206E 30 1.1811 62 2.4409 20 .7874 1.0 .039 .33 1.9 3 2 23 800 5 350 6 700 1 510 9 500 12 000
2207E 35 1.3780 72 2.8346 23 .9055 1.0 .039 .31 2 3.1 2.2 30 700 6 900 8 800 1 980 8 500 10 000
2208E 40 1.5748 80 3.1496 23 .9055 1.0 .039 .28 2.2 3.5 2.5 31 900 7 170 10 000 2 250 7 500 9 000
2209E 45 1.7717 85 3.3465 23 .9055 1.0 .039 .26 2.4 3.7 2.5 32 500 7 310 10 600 2 380 7 000 8 500
2210E 50 1.9685 90 3.5433 23 .9055 1.0 .039 .23 2.7 4.2 2.8 33 800 7 600 11 200 2 520 6 300 7 500
2211E 55 2.1654 100 3.9370 25 .9843 1.5 .059 .23 2.7 4.2 2.8 39 000 8 770 13 400 3 010 6 000 7 000
2212E 60 2.3622 110 4.3307 28 1.1024 1.5 .059 .24 2.6 4.1 2.8 48 800 11 000 17 000 3 820 5 300 6 300
2213E 65 2.5591 120 4.7244 31 1.2205 1.5 .059 .24 2.6 4.1 2.8 57 200 12 900 20 000 4 500 5 000 6 000
2214 70 2.7559 125 4.9213 31 1.2205 1.5 .059 .27 2.3 3.6 2.5 44 200 9 940 17 000 3 820 4 800 5 600
2215 75 2.9528 130 5.1181 31 1.2205 1.5 .059 .25 2.5 3.9 2.5 44 200 9 940 18 000 4 050 4 500 5 300
2216E 80 3.1496 140 5.5118 33 1.2992 2.0 .079 .22 2.9 4.5 2.8 65 000 14 600 25 500 5 730 4 000 4 800
2217 85 3.3465 150 5.9055 36 1.4173 2.0 .079 .25 2.5 3.9 2.5 58 500 13 200 23 600 5 310 3 800 4 500
2218 90 3.5433 160 6.2992 40 1.5748 2.0 .079 .27 2.3 3.6 2.5 70 200 15 800 28 500 6 410 3 600 4 300
2219 95 3.7402 170 6.6929 43 1.6929 2.0 .079 .27 2.3 3.6 2.5 83 200 18 700 34 500 7 760 3 400 4 000
2220 100 3.9370 180 7.0866 46 1.8110 2.0 .079 .27 2.3 3.6 2.5 97 500 21 900 40 500 9 110 3 200 3 800
2221 105 4.1339 190 7.4803 50 1.9685 2.0 .079 .28 2.2 3.5 2.5 108 000 24 300 45 000 10 100 3 000 3 600
2222 110 4.3307 200 7.8740 53 2.0866 2.0 .079 .28 2.2 3.5 2.5 124 000 27 900 52 000 11 700 2 800 3 400
2301 12 .4724 37 1.4567 17 .6693 1.0 .039 .60 1.05 1.6 1.1 11 700 2 630 2 700 607 17 000 20 000
2302 15 .5906 42 1.6535 17 .6693 1.0 .039 .52 1.2 1.9 1.3 11 900 2 680 2 900 652 15 000 18 000
2303 17 .6693 47 1.8504 19 .7480 1.0 .039 .52 1.2 1.9 1.3 14 600 3 280 3 550 798 13 000 16 000
2304 20 .7874 52 2.0472 21 .8268 1.0 .039 .52 1.2 1.9 1.3 18 200 4 090 4 750 1 070 11 000 14 000
2305 25 .9843 62 2.4409 24 .9449 1.0 .039 .48 1.3 2 1.4 24 200 5 440 6 550 1 470 9 500 12 000
2306 30 1.1811 72 2.8346 27 1.0630 1.0 .039 .44 1.4 2.2 1.4 31 200 7 010 8 800 1 980 8 500 10 000
2307E 35 1.3780 80 3.1496 31 1.2205 1.5 .059 .46 1.35 2.1 1.4 39 700 8 930 11 200 2 520 7 000 8 500
2308E 40 1.5748 90 3.5433 33 1.2992 1.5 .059 .40 1.6 2.4 1.6 54 000 12 100 16 000 3 600 6 300 7 500
2309E 45 1.7717 100 3.9370 36 1.4173 1.5 .059 .33 1.9 3 2 63 700 14 300 19 300 4 340 5 600 6 700
2310 50 1.9685 110 4.3307 40 1.5748 2.0 .079 .43 1.5 2.3 1.6 63 700 14 300 20 000 4 500 5 300 6 300
2311 55 2.1654 120 4.7244 43 1.6929 2.0 .079 .40 1.6 2.4 1.6 76 100 17 100 24 000 5 400 4 800 5 600
2312 60 2.3622 130 5.1181 46 1.8110 2.0 .079 .33 1.9 3 2 87 100 19 600 28 500 6 410 4 500 5 300
2313 65 2.5591 140 5.5118 48 1.8898 2.0 .079 .37 1.7 2.6 1.8 95 600 21 500 32 500 7 310 4 000 4 800
2314 70 2.7559 150 5.9055 51 2.0079 2.0 .079 .37 1.7 2.6 1.8 111 000 25 000 37 500 8 430 3 800 4 500
2315 75 2.9528 160 6.2992 55 2.1654 2.0 .079 .37 1.7 2.6 1.8 124 000 27 900 43 000 9 670 3 400 4 000
2316 80 3.1496 170 6.6929 58 2.2835 2.0 .079 .37 1.7 2.6 1.8 135 000 30 400 49 000 11 000 3 200 3 800
2317 85 3.3465 180 7.0866 60 2.3622 2.5 .098 .37 1.7 2.6 1.8 140 000 31 500 51 000 11 500 3 000 3 600
2318 90 3.5433 190 7.4803 64 2.5197 2.5 .098 .37 1.7 2.6 1.8 153 000 34 400 57 000 12 800 2 800 3 400
2319 95 3.7402 200 7.8740 67 2.6378 2.5 .098 .37 1.7 2.6 1.8 165 000 37 100 64 000 14 400 2 600 3 200
2320 100 3.9370 215 8.4646 73 2.8740 2.5 .098 .37 1.7 2.6 1.8 190 000 42 700 80 000 18 000 2 400 3 000
2322 110 4.3307 240 9.4488 80 3.1496 2.5 .098 .37 1.7 2.6 1.8 216 000 48 600 95 000 21 400 2 200 2 800
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
69
1200-K, 1200-EK, 1300-K, 1300-EK Series
Self-Aligning Ball Bearings with Tapered Bore MRC Bearing Services
1204EK 20 .7874 47 1.8504 14 .5512 1.0 .039 .30 2.1 3.3 2.2 12 700 2 860 3 400 764 15 000 18 000
1205EK 25 .9843 52 2.0472 15 .5906 1.0 .039 .28 2.2 3.5 2.5 14 300 3 220 4 000 899 13 000 16 000
1206EK 30 1.1811 62 2.4409 16 .6299 1.0 .039 .25 2.5 3.9 2.5 15 600 3 510 4 650 1 050 10 000 13 000
1207EK 35 1.3780 72 2.8346 17 .6693 1.0 .039 .23 2.7 4.2 2.8 19 000 4 270 6 000 1 350 9 000 11 000
1208EK 40 1.5748 80 3.1496 18 .7087 1.0 .039 .22 2.9 4.5 2.8 19 900 4 470 6 950 1 560 8 500 10 000
1209EK 45 1.7717 85 3.3465 19 .7480 1.0 .039 .21 3 4.6 3.2 22 900 5 150 7 800 1 750 7 500 9 000
1210EK 50 1.9685 90 3.5433 20 .7874 1.0 .039 .21 3 4.6 3.2 26 500 5 960 9 150 2 060 7 000 8 500
1211EK 55 2.1654 100 3.9370 21 .8268 1.5 .059 .19 3.3 5.1 3.6 27 600 6 210 10 600 2 380 6 300 7 500
1212EK 60 2.3622 110 4.3307 22 .8661 1.5 .059 .19 3.3 5.1 3.6 31 200 7 010 12 200 2 740 5 600 6 700
1213EK 65 2.5591 120 4.7244 23 .9055 1.5 .059 .18 3.5 5.4 3.6 35 100 7 890 14 000 3 150 5 300 6 300
1215K 75 2.9528 130 5.1181 25 .9843 1.5 .059 .17 3.7 5.7 4 39 000 8 770 15 600 3 510 4 800 5 600
1216K 80 3.1496 140 5.5118 26 1.0236 2.0 .079 .16 3.9 6.1 4 39 700 8 930 17 000 3 820 4 500 5 300
1217K 85 3.3465 150 5.9055 28 1.1024 2.0 .079 .17 3.7 5.7 4 48 800 11 000 20 800 4 680 4 000 4 800
1218K 90 3.5433 160 6.2992 30 1.1811 2.0 .079 .17 3.7 5.7 4 57 200 12 900 23 600 5 310 3 800 4 500
1219K 95 3.7402 170 6.6929 32 1.2598 2.0 .079 .17 3.7 5.7 4 63 700 14 300 27 000 6 070 3 600 4 300
1220K 100 3.9370 180 7.0866 34 1.3386 2.0 .079 .17 3.7 5.7 4 68 900 15 500 30 000 6 740 3 400 4 000
1221K 105 4.1339 190 7.4803 36 1.4173 2.0 .079 .17 3.7 5.7 4 74 100 16 700 32 500 7 310 3 200 3 800
1222K 110 4.3307 200 7.8740 38 1.4961 2.0 .079 .17 3.7 5.7 4 88 400 19 900 39 000 8 770 3 000 3 600
1224K 120 4.7244 215 8.4646 42 1.6535 2.0 .079 .19 3.3 5.1 3.6 11 900 26 800 53 000 11 900 2 800 3 400
1304EK 20 .7874 52 2.0472 15 .5906 1.0 .039 .28 2.2 3.5 2.5 14 300 3 220 4 000 899 12 000 15 000
1305EK 25 .9843 62 2.4409 17 .6693 1.0 .039 .28 2.2 3.5 2.5 19 000 4 270 5 400 1 210 9 500 12 000
1306EK 30 1.1811 72 2.8346 19 .7480 1.0 .039 .25 2.5 3.9 2.5 22 500 5 060 6 800 1 530 9 000 11 000
1307EK 35 1.3780 80 3.1496 21 .8268 1.5 .059 .25 2.5 3.9 2.5 26 500 5 960 8 500 1 910 7 500 9 000
1308EK 40 1.5748 90 3.5433 23 .9055 1.5 .059 .23 2.7 4.2 2.8 33 800 7 600 11 200 2 520 6 700 8 000
1309EK 45 1.7717 100 3.9370 25 .9843 1.5 .059 .23 2.7 4.2 2.8 39 000 8 770 13 400 3 010 6 300 7 500
1310EK 50 1.9685 110 4.3307 27 1.0630 2.0 .079 .24 2.6 4.1 2.8 43 600 9 800 14 000 3 150 5 600 6 700
1311EK 55 2.1654 120 4.7244 29 1.1417 2.0 .079 .23 2.7 4.2 2.8 50 700 11 400 18 000 4 050 5 000 6 000
1312EK 60 2.3622 130 5.1181 31 1.2205 2.0 .079 .23 2.7 4.2 2.8 58 500 13 200 22 000 4 950 4 500 5 300
1313EK 65 2.5591 140 5.5118 33 1.2992 2.0 .079 .22 2.9 4.5 2.8 65 000 14 600 25 500 5 730 4 300 5 000
1315K 75 2.9528 160 6.2992 37 1.4567 2.0 .079 .22 2.9 4.5 2.8 79 300 17 800 30 000 6 740 3 800 4 500
1316K 80 3.1496 170 6.6929 39 1.5354 2.0 .079 .22 2.9 4.5 2.8 88 400 19 900 33 500 7 530 3 600 4 300
1317K 85 3.3465 180 7.0866 41 1.6142 2.5 .098 .22 2.9 4.5 2.8 97 500 21 900 38 000 8 540 3 400 4 000
1318K 90 3.5433 190 7.4803 43 1.6929 2.5 .098 .22 2.9 4.5 2.8 117 000 26 300 44 000 9 890 3 200 3 800
1319K 95 3.7402 200 7.8740 45 1.7717 2.5 .098 .23 2.7 4.2 2.8 133 000 29 900 51 000 11 500 3 000 3 600
1320K 100 3.9370 215 8.4646 47 1.8504 2.5 .098 .23 2.7 4.2 2.8 143 000 32 200 57 000 12 800 2 800 3 400
1322K 110 4.3307 240 9.4488 50 1.9685 2.5 .098 .22 2.9 4.5 2.8 163 000 36 600 72 000 16 200 2 400 3 000
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
70
2200-K, 2200-EK, 2300-K, 2300-EK Series
Self-Aligning Ball Bearings with Tapered Bore
2205EK 25 .9843 52 2.0472 18 .7087 1.0 .039 .35 1.8 2.8 1.8 16 800 3 780 4 400 989 11 000 14 000
2206EK 30 1.1811 62 2.4409 20 .7874 1.0 .039 .33 1.9 3 2 23 800 5 350 6 700 1 510 9 500 12 000
2207EK 35 1.3780 72 2.8346 23 .9055 1.0 .039 .31 2 3.1 2.2 30 700 6 900 8 800 1 980 8 500 10 000
2208EK 40 1.5748 80 3.1496 23 .9055 1.0 .039 .28 2.2 3.5 2.5 31 900 7 170 10 000 2 250 7 500 9 000
2209EK 45 1.7717 85 3.3465 23 .9055 1.0 .039 .26 2.4 3.7 2.5 32 500 7 310 10 600 2 380 7 000 8 500
2210EK 50 1.9685 90 3.5433 23 .9055 1.0 .039 .23 2.7 4.2 2.8 33 800 7 600 11 200 2 520 6 300 7 500
2211EK 55 2.1654 100 3.9370 25 .9843 1.5 .059 .23 2.7 4.2 2.8 39 000 8 770 13 400 3 010 6 000 7 000
2212EK 60 2.3622 110 4.3307 28 1.1024 1.5 .059 .24 2.6 4.1 2.8 48 800 11 000 17 000 3 820 5 300 6 300
2213EK 65 2.5591 120 4.7244 31 1.2205 1.5 .059 .24 2.6 4.1 2.8 57 200 12 900 20 000 4 500 5 000 6 000
2215K 75 2.9528 130 5.1181 31 1.2205 1.5 .059 .25 2.5 3.9 2.5 44 200 9 940 18 000 4 050 4 500 5 300
2216EK 80 3.1496 140 5.5118 33 1.2992 2.0 .079 .22 2.9 4.5 2.8 65 000 14 600 25 500 5 730 4 000 4 800
2217K 85 3.3465 150 5.9055 36 1.4173 2.0 .079 .25 2.5 3.9 2.5 58 500 13 200 23 600 5 310 3 800 4 500
2218K 90 3.5433 160 6.2992 40 1.5748 2.0 .079 .27 2.3 3.6 2.5 70 200 15 800 28 500 6 410 3 600 4 300
2219K 95 3.7402 170 6.6929 43 1.6929 2.0 .079 .27 2.3 3.6 2.5 83 200 18 700 34 500 7 760 3 400 4 000
2220K 100 3.9370 180 7.0866 46 1.8110 2.0 .079 .27 2.3 3.6 2.5 97 500 21 900 40 500 9 110 3 200 3 800
2221K 105 4.1339 190 7.4803 50 1.9685 2.0 .079 .28 2.2 3.5 2.5 108 000 24 300 45 000 10 100 3 000 3 600
2222K 110 4.3307 200 7.8740 53 2.0866 2.0 .079 .28 2.2 3.5 2.5 124 000 27 900 52 000 11 700 2 800 3 400
2305K 25 .9843 62 2.4409 24 .9449 1.0 .039 .48 1.3 2 1.4 24 200 5 440 6 550 1 470 9 500 12 000
2306K 30 1.1811 72 2.8346 27 1.0630 1.0 .039 .44 1.4 2.2 1.4 31 200 7 010 8 800 1 980 8 500 10 000
2307EK 35 1.3780 80 3.1496 31 1.2205 1.5 .059 .46 1.35 2.1 1.4 39 700 8 930 11 200 2 520 7 000 8 500
2308EK 40 1.5748 90 3.5433 33 1.2992 1.5 .059 .40 1.6 2.4 1.6 54 000 12 100 16 000 3 600 6 300 7 500
2309EK 45 1.7717 100 3.9370 36 1.4173 1.5 .059 .33 1.9 3 2 63 700 14 300 19 300 4 340 5 600 6 700
2310K 50 1.9685 110 4.3307 40 1.5748 2.0 .079 .43 1.5 2.3 1.6 63 700 14 300 20 000 4 500 5 300 6 300
2311K 55 2.1654 120 4.7244 43 1.6929 2.0 .079 .40 1.6 2.4 1.6 76 100 17 100 24 000 5 400 4 800 5 600
2312K 60 2.3622 130 5.1181 46 1.8110 2.0 .079 .33 1.9 3 2 87 100 19 600 28 500 6 410 4 500 5 300
2313K 65 2.5591 140 5.5118 48 1.8898 2.0 .079 .37 1.7 2.6 1.8 95 600 21 500 32 500 7 310 4 000 4 800
2315K 75 2.9528 160 6.2992 55 2.1654 2.0 .079 .37 1.7 2.6 1.8 124 000 27 900 43 000 9 670 3 400 4 000
2316K 80 3.1496 170 6.6929 58 2.2835 2.0 .079 .37 1.7 2.6 1.8 135 000 30 400 49 000 11 000 3 200 3 800
2317K 85 3.3465 180 7.0866 60 2.3622 2.5 .098 .37 1.7 2.6 1.8 140 000 31 500 51 000 11 500 3 000 3 600
2318K 90 3.5433 190 7.4803 64 2.5197 2.5 .098 .37 1.7 2.6 1.8 153 000 34 400 57 000 12 800 2 800 3 400
2319K 95 3.7402 200 7.8740 67 2.6378 2.5 .098 .37 1.7 2.6 1.8 165 000 37 100 64 000 14 400 2 600 3 200
2320K 100 3.9370 215 8.4646 73 2.8740 2.5 .098 .37 1.7 2.6 1.8 190 000 42 700 80 000 18 000 2 400 3 000
2322K 110 4.3307 240 9.4488 80 3.1496 2.5 .098 .37 1.7 2.6 1.8 216 000 48 600 95 000 21 400 2 200 2 800
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
71
1200-K, 1200-EK, 1300-K, 1300-EK
Self-Aligning Series with Adapter Sleeve MRC Bearing Services
1204EK H204 17 .6693 47 1.8504 14 .5512 1.0 .039 .30 2.1 3.3 2.2 12 700 2 860 3 400 764 15 000 18 000
1205EK H205 20 .7874 52 2.0472 15 .5906 1.0 .039 .28 2.2 3.5 2.5 14 300 3 220 4 000 899 13 000 16 000
1206EK H206 25 .9843 62 2.4409 16 .6299 1.0 .039 .25 2.5 3.9 2.5 15 600 3 510 4 650 1 050 10 000 13 000
1207EK H207 30 1.1811 72 2.8346 17 .6693 1.0 .039 .23 2.7 4.2 2.8 19 000 4 270 6 000 1 350 9 000 11 000
1208EK H208 35 1.3780 80 3.1496 18 .7087 1.0 .039 .22 2.9 4.5 2.8 19 900 4 470 6 950 1 560 8 500 10 000
1209EK H209 40 1.5748 85 3.3465 19 .7480 1.0 .039 .21 3 4.6 3.2 22 900 5 150 7 800 1 750 7 500 9 000
1210EK H210 45 1.7717 90 3.5433 20 .7874 1.0 .039 .21 3 4.6 3.2 26 500 5 960 9 150 2 060 7 000 8 500
1211EK H211 50 1.9685 100 3.9370 21 .8268 1.5 .059 .19 3.3 5.1 3.6 27 600 6 210 10 600 2 380 6 300 7 500
1212EK H212 55 2.1654 110 4.3307 22 .8661 1.5 .059 .19 3.3 5.1 3.6 31 200 7 010 12 200 2 740 5 600 6 700
1213EK H213 60 2.3622 120 4.7244 23 .9055 1.5 .059 .18 3.5 5.4 3.6 35 100 7 890 14 000 3 150 5 300 6 300
1215K H215 65 2.5591 130 5.1181 25 .9843 1.5 .059 .17 3.7 5.7 4 39 000 8 770 15 600 3 510 4 800 5 600
1216K H216 70 2.7559 140 5.5118 26 1.0236 2.0 .079 .16 3.9 6.1 4 39 700 8 930 17 000 3 820 4 500 5 300
1217K H217 75 2.9528 150 5.9055 28 1.1024 2.0 .079 .17 3.7 5.7 4 48 800 11 000 20 800 4 680 4 000 4 800
1218K H218 80 3.1496 160 6.2992 30 1.1811 2.0 .079 .17 3.7 5.7 4 57 200 12 900 23 600 5 310 3 800 4 500
1219K H219 85 3.3465 170 6.6929 32 1.2598 2.0 .079 .17 3.7 5.7 4 63 700 14 300 27 000 6 070 3 600 4 300
1220K H220 90 3.5433 180 7.0866 34 1.3386 2.0 .079 .17 3.7 5.7 4 68 900 15 500 30 000 6 740 3 400 4 000
1221K H221 95 3.7402 190 7.4803 36 1.4173 2.0 .079 .17 3.7 5.7 4 74 100 16 700 32 500 7 310 3 200 3 800
1222K H222 100 3.9370 200 7.8740 38 1.4961 2.0 .079 .17 3.7 5.7 4 88 400 19 900 39 000 8 770 3 000 3 600
1224K H3024 110 4.3307 215 8.4646 42 1.6535 2.0 .079 .19 3.3 5.1 3.6 119 000 26 800 53 000 11 900 2 800 3 400
1304EK H304 17 .6693 52 2.0472 15 .5906 1.0 .039 .28 2.2 3.5 2.5 14 300 3 220 4 000 899 12 000 14 000
1305EK H305 20 .7874 62 2.4409 17 .6693 1.0 .039 .28 2.2 3.5 2.5 19 000 4 270 5 400 1 210 9 500 12 000
1306EK H306 25 .9843 72 2.8346 19 .7480 1.0 .039 .25 2.5 3.9 2.5 22 500 5 060 6 800 1 530 9 000 11 000
1307EK H307 30 1.1811 80 3.1496 21 .8268 1.5 .059 .25 2.5 3.9 2.5 26 500 5 960 8 500 1 910 7 500 9 000
1308EK H308 35 1.3780 90 3.5433 23 .9055 1.5 .059 .23 2.7 4.2 2.8 33 800 7 600 11 200 2 520 6 700 8 000
1309EK H309 40 1.5748 100 3.9370 25 .9843 1.5 .059 .23 2.7 4.2 2.8 39 000 8 770 13 400 3 010 6 300 7 500
1310EK H310 45 1.7717 110 4.3307 27 1.0630 2.0 .079 .24 2.6 4.1 2.8 43 600 9 800 14 000 3 150 5 600 6 700
1311EK H311 50 1.9685 120 4.7244 29 1.1417 2.0 .079 .23 2.7 4.2 2.8 50 700 11 400 18 000 4 050 5 000 6 000
1312EK H312 55 2.1654 130 5.1181 31 1.2205 2.0 .079 .23 2.7 4.2 2.8 58 500 13 200 22 000 4 950 4 500 5 300
1313EK H313 60 2.3622 140 5.5118 33 1.2992 2.0 .079 .22 2.9 4.5 2.8 65 000 14 600 25 500 5 730 4 300 5 000
1315K H315 65 2.5591 160 6.2992 37 1.4567 2.0 .079 .22 2.9 4.5 2.8 79 300 17 800 30 000 6 740 3 800 4 500
1316K H316 70 2.7559 170 6.6929 39 1.5354 2.0 .079 .22 2.9 4.5 2.8 88 400 19 900 33 500 7 530 3 600 4 300
1317K H317 75 2.9528 180 7.0866 41 1.6142 2.5 .098 .22 2.9 4.5 2.8 97 500 21 900 38 000 8 540 3 400 4 000
1318K H318 80 3.1496 190 7.4803 43 1.6929 2.5 .098 .22 2.9 4.5 2.8 117 000 26 300 44 000 9 890 3 200 3 800
1319K H319 85 3.3465 200 7.8740 45 1.7717 2.5 .098 .23 2.7 4.2 2.8 133 000 29 900 51 000 11 500 3 000 3 600
1320K H320 90 3.5433 215 8.4646 47 1.8504 2.5 .098 .23 2.7 4.2 2.8 143 000 32 200 57 000 12 800 2 800 3 400
1322K H322 100 3.9370 240 9.4488 50 1.9685 2.5 .098 .22 2.9 4.5 2.8 163 000 36 600 72 000 16 200 2 400 3 000
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
72
2200-K, 2200-EK, 2300-K, 2300-EK
Self-Aligning Series with Adapter Sleeve
2205EK H305 20 .7874 52 2.0472 18 .7087 1.0 .039 .35 1.8 2.8 1.8 16 800 3 780 4 400 989 11 000 14 000
2206EK H306 25 .9843 62 2.4409 20 .7874 1.0 .039 .33 1.9 3 2 23 800 5 350 6 700 1 510 9 500 12 000
2207EK H307 30 1.1811 72 2.8346 23 .9055 1.0 .039 .31 2 3.1 2.2 30 700 6 900 8 800 1 980 8 500 10 000
2208EK H308 35 1.3780 80 3.1496 23 .9055 1.0 .039 .28 2.2 3.5 2.5 31 900 7 170 10 000 2 250 7 500 9 000
2209EK H309 40 1.5748 85 3.3465 23 .9055 1.0 .039 .26 2.4 3.7 2.5 32 500 7 310 10 600 2 380 7 000 8 500
2210EK H310 45 1.7717 90 3.5433 23 .9055 1.0 .039 .23 2.7 4.2 2.8 33 800 7 600 11 200 2 520 6 300 7 500
2211EK H311 50 1.9685 100 3.9370 25 .9843 1.5 .059 .23 2.7 4.2 2.8 39 000 8 770 13 400 3 010 6 000 7 000
2212EK H312 55 2.1654 110 4.3307 28 1.1024 1.5 .059 .24 2.6 4.1 2.8 48 800 11 000 17 000 3 820 5 300 6 300
2213EK H313 60 2.3622 120 4.7244 31 1.2205 1.5 .059 .24 2.6 4.1 2.8 57 200 12 900 20 000 4 500 5 000 6 000
2215K H315 65 2.5591 130 5.1181 31 1.2205 1.5 .059 .25 2.5 3.9 2.5 44 200 9 940 18 000 4 050 4 500 5 300
2216EK H316 70 2.7559 140 5.5118 33 1.2992 2.0 .079 .22 2.9 4.5 2.8 65 000 14 600 25 500 5 730 4 000 4 800
2217K H317 75 2.9528 150 5.9055 36 1.4173 2.0 .079 .25 2.5 3.9 2.5 58 500 13 200 23 600 5 310 3 800 4 500
2218K H318 80 3.1496 160 6.2992 40 1.5748 2.0 .079 .27 2.3 3.6 2.5 70 200 15 800 28 500 6 410 3 600 4 300
2219K H319 85 3.3465 170 6.6929 43 1.6929 2.0 .079 .27 2.3 3.6 2.5 83 200 18 700 34 500 7 760 3 400 4 000
2220K H320 90 3.5433 180 7.0866 46 1.8110 2.0 .079 .27 2.3 3.6 2.5 97 500 21 900 40 500 9 110 3 200 3 800
2221K H321 95 3.7402 190 7.4803 50 1.9685 2.0 .079 .28 2.2 3.5 2.5 108 000 24 300 45 000 10 100 3 000 3 600
2222K H322 100 3.9370 200 7.8740 53 2.0866 2.0 .079 .28 2.2 3.5 2.5 124 000 27 900 52 000 11 700 2 800 3 400
2305K H2305 20 .7874 62 2.4409 24 .9449 1.0 .039 .48 1.3 2 1.4 24 200 5 440 6 550 1 470 9 500 12 000
2306K H2306 25 .9843 72 2.8346 27 1.0630 1.0 .039 .44 1.4 2.2 1.4 31 200 7 010 8 800 1 980 8 500 10 000
2307EK H2307 30 1.1811 80 3.1496 31 1.2205 1.5 .059 .46 1.35 2.1 1.4 39 700 8 930 11 200 2 520 7 000 8 500
2308EK H2308 35 1.3780 90 3.5433 33 1.2992 1.5 .059 .40 1.6 2.4 1.6 54 000 12 100 16 000 3 600 6 300 7 500
2309EK H2309 40 1.5748 100 3.9370 36 1.4173 1.5 .059 .33 1.9 3 2 63 700 14 300 19 300 4 340 5 600 6 700
2310K H2310 45 1.7717 110 4.3307 40 1.5748 2.0 .079 .43 1.5 2.3 1.6 63 700 14 300 20 000 4 500 5 300 6 300
2311K H2311 50 1.9685 120 4.7244 43 1.6929 2.0 .079 .40 1.6 2.4 1.6 76 100 17 100 24 000 5 400 4 800 5 600
2312K H2312 55 2.1654 130 5.1181 46 1.8110 2.0 .079 .33 1.9 3 2 87 100 19 600 28 500 6 410 4 500 5 300
2313K H2313 60 2.3622 140 5.5118 48 1.8898 2.0 .079 .37 1.7 2.6 1.8 95 600 21 500 32 500 7 310 4 000 4 800
2315K H2315 65 2.5591 160 6.2992 55 2.1654 2.0 .079 .37 1.7 2.6 1.8 124 000 27 900 43 000 9 670 3 400 4 000
2316K H2316 70 2.7559 170 6.6929 58 2.2835 2.0 .079 .37 1.7 2.6 1.8 135 000 30 400 49 000 11 000 3 200 3 800
2317K H2317 75 2.9528 180 7.0866 60 2.3622 2.5 .098 .37 1.7 2.6 1.8 140 000 31 500 51 000 11 500 3 000 3 600
2318K H2318 80 3.1496 190 7.4803 64 2.5197 2.5 .098 .37 1.7 2.6 1.8 153 000 34 400 57 000 12 800 2 800 3 400
2319K H2319 85 3.3465 200 7.8740 67 2.6378 2.5 .098 .37 1.7 2.6 1.8 165 000 37 100 64 000 14 400 2 600 3 200
2320K H2320 90 3.5433 215 8.4646 73 2.8740 2.5 .098 .37 1.7 2.6 1.8 190 000 42 700 80 000 18 000 2 400 3 000
2322K H2322 100 3.9370 240 9.4488 80 3.1496 2.5 .098 .37 1.7 2.6 1.8 216 000 48 600 95 000 21 400 2 200 2 800
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
73
2200 and 2300 Self-Aligning Series with Seals,
and with Seals and Tapered Bore MRC Bearing Services
2200E2RS1 10 .3937 30 1.1811 14 .5512 .60 .024 .33 1.9 3 2 5 530 1 240 1 180 265 17 000
2201E2RS1 12 .4724 32 1.2598 14 .5512 .60 .024 .33 1.9 3 2 6 240 1 400 1 430 321 16 000
2202E2RS1 15 .5906 35 1.3780 14 .5512 .60 .024 .33 1.9 3 2 7 410 1 670 1 760 396 14 000
2203E2RS1 17 .6693 40 1.5748 16 .6299 .60 .024 .31 2 3.1 2.2 8 840 1 990 2 200 495 12 000
2204E2RS1 20 .7874 47 1.8504 18 .7087 1.0 .039 .30 2.1 3.3 2.2 12 700 2 860 3 400 764 10 000
2205E2RS1 25 .9843 52 2.0472 18 .7087 1.0 .039 .28 2.2 3.5 2.5 14 300 3 220 4 000 899 9 000
2206E2RS1 30 1.1811 62 2.4409 20 .7874 1.0 .039 .25 2.5 3.9 2.5 15 600 3 510 4 650 1 050 7 500
2207E2RS1 35 1.3780 72 2.8346 23 .9055 1.0 .039 .23 2.7 4.2 2.8 19 000 4 270 6 000 1 350 6 300
2208E2RS1 40 1.5748 80 3.1496 23 .9055 1.0 .039 .22 2.9 4.5 2.8 19 900 4 470 6 950 1 560 5 600
2209E2RS1 45 1.7717 85 3.3465 23 .9055 1.0 .039 .21 3 4.6 3.2 22 900 5 150 7 800 1 750 5 300
22102RS1 50 1.9685 90 3.5433 23 .9055 1.0 .039 .20 3.2 4.9 3.2 22 900 5 150 8 150 1 830 4 800
2211E2RS1 55 2.1654 100 3.9370 25 .9843 1.5 .059 .19 3.3 5.1 3.6 27 600 6 210 10 600 2 380 4 300
2212E2RS1 60 2.3622 110 4.3307 28 1.1024 1.5 .059 .19 3.3 5.1 3.6 31 200 7 010 12 200 2 740 3 800
2213E2RS1 65 2.5591 120 4.7244 31 1.2205 1.5 .059 .18 3.5 5.4 3.6 35 100 7 890 14 000 3 150 3 600
22142RS1 70 2.7559 125 4.9213 31 1.2205 1.5 .059 .18 3.5 5.4 3.6 34 500 7 760 13 700 3 080 3 400
2302E2RS1 15 .5906 42 1.6535 17 .6693 1.0 .039 .31 2 3.1 2.2 10 800 2 430 2 600 585 12 000
2303E2RS1 17 .6693 47 1.8504 19 .7480 1.0 .039 .30 2.1 3.3 2.2 12 700 2 860 3 400 764 11 000
2304E2RS1 20 .7874 52 2.0472 21 .8268 1.0 .039 .28 2.2 3.5 2.5 14 300 3 220 4 000 899 9 500
2305E2RS1 25 .9843 62 2.4409 24 .9449 1.0 .039 .28 2.2 3.5 2.5 19 000 4 270 5 400 1 210 7 500
2306E2RS1 30 1.1811 72 2.8346 27 1.0630 1.0 .039 .25 2.5 3.9 2.5 22 500 5 060 6 800 1 530 6 700
2307E2RS1 35 1.3780 80 3.1496 31 1.2205 1.5 .059 .25 2.5 3.9 2.5 26 500 5 960 8 500 1 910 5 600
2308E2RS1 40 1.5748 90 3.5433 33 1.2992 1.5 .059 .23 2.7 4.2 2.8 33 800 7 600 11 200 2 520 5 000
2309E2RS1 45 1.7717 100 3.9370 36 1.4173 1.5 .059 .23 2.7 4.2 2.8 39 000 8 770 13 400 3 010 4 500
2310E2RS1 50 1.9685 110 4.3307 40 1.5748 2.0 .079 .24 2.6 4.1 2.8 43 600 9 800 14 000 3 150 4 000
Tapered Bore
2205E2RS1K 25 .9843 52 2.0472 18 .7087 1.0 .039 .28 2.2 3.5 2.5 14 300 3 220 4 000 899 9 000
2206E2RS1K 30 1.1811 62 2.4409 20 .7874 1.0 .039 .25 2.5 3.9 2.5 15 600 3 510 4 650 1 050 7 500
2207E2RS1K 35 1.3780 72 2.8346 23 .9055 1.0 .039 .23 2.7 4.2 2.8 19 000 4 270 6 000 1 350 6 300
2208E2RS1K 40 1.5748 80 3.1496 23 .9055 1.0 .039 .22 2.9 4.5 2.8 19 900 4 470 6 950 1 560 5 600
2209E2RS1K 45 1.7717 85 3.3465 23 .9055 1.0 .039 .21 3 4.6 3.2 22 900 5 150 7 800 1 750 5 300
22102RS1K 50 1.9685 90 3.5433 23 .9055 1.0 .039 .20 3.2 4.9 3.2 22 900 5 150 8 150 1 830 4 800
2211E2RS1K 55 2.1654 100 3.9370 25 .9843 1.5 .059 .19 3.3 5.1 3.6 27 600 6 210 10 600 2 380 4 300
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
74
11200-E, 11300-E Series
Self-Aligning with Extended Inner Ring
11204E 20 .7874 47 1.8504 14 .5512 40 1.575 1.0 .039 .30 2.1 3.3 2.2 12 700 2 860 3 400 764 9 000
11205E 25 .9843 52 2.0472 15 .5906 44 1.732 1.0 .039 .28 2.2 3.5 2.5 14 300 3 220 4 000 899 8 000
11206E 30 1.1811 62 2.4409 16 .6299 48 1.890 1.0 .039 .25 2.5 3.9 2.5 15 600 3 510 4 650 1 050 6 700
11207E 35 1.3780 72 2.8346 17 .6693 52 2.047 1.0 .039 .23 2.7 4.2 2.8 19 000 4 270 6 000 1 350 5 600
11208E 40 1.5748 80 3.1496 18 .7087 56 2.205 1.0 .039 .22 2.9 4.5 2.8 19 900 4 470 6 950 1 560 5 000
11209E 45 1.7717 85 3.3465 19 .7480 58 2.283 1.0 .039 .21 3 4.6 3.2 22 900 5 150 7 800 1 750 4 500
11210E 50 1.9685 90 3.5433 20 .7874 58 2.283 1.0 .039 .21 3 4.6 3.2 26 500 5 960 9 150 2 060 4 300
11212E 60 2.3622 110 4.3307 22 .8661 62 2.441 1.5 .059 .19 3.3 5.1 3.6 31 200 7 010 12 200 2 740 3 400
11305E 25 .9843 62 2.4409 17 .6693 48 1.890 1.0 .039 .28 2.2 3.5 2.5 19 000 4 270 5 400 1 210 6 700
11306E 30 1.1811 72 2.8346 19 .7480 52 2.047 1.0 .039 .25 2.5 3.9 2.5 22 500 5 060 6 800 1 530 5 600
11307E 35 1.3780 80 3.1496 21 .8268 56 2.205 1.5 .059 .25 2.5 3.9 2.5 26 500 5 960 8 500 1 910 5 000
11308E 40 1.5748 90 3.5433 23 .9055 58 2.283 1.5 .059 .23 2.7 4.2 2.8 33 800 7 600 11 200 2 520 4 500
11310E 50 1.9685 110 4.3307 27 1.0630 62 2.441 2.0 .079 .24 2.6 4.1 2.8 43 600 9 800 14 000 3 150 3 600
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
75
Radial Internal Clearance
of Self-Aligning Ball Bearings MRC Bearing Services
14 .5512 18 .7087 3 12 1 5 8 21 3 8 15 28 6 11 23 37 9 15
18 .7087 24 .9449 4 14 2 6 10 23 4 9 17 30 7 12 25 39 10 15
24 .9449 30 1.1811 5 16 2 6 11 24 4 9 19 35 7 14 29 46 11 18
30 1.1811 40 1.5748 6 18 2 7 13 29 5 11 23 40 9 16 34 53 13 21
40 1.5748 50 1.9685 6 19 2 7 14 31 6 12 25 44 10 17 37 57 15 22
50 1.9685 65 2.5591 7 21 3 8 16 36 6 14 30 50 12 20 45 69 18 27
65 2.5591 80 3.1496 8 24 3 9 18 40 7 16 35 60 14 24 54 83 21 33
80 3.1496 100 3.9370 9 27 4 11 22 48 9 19 42 70 17 28 64 96 25 38
100 3.9370 120 4.7244 10 31 4 12 25 56 10 22 50 83 20 33 75 114 30 45
40 1.5748 50 1.9685 14 27 6 11 22 39 9 15 33 52 13 20 45 65 18 26
50 1.9685 65 2.5591 18 32 7 13 27 47 11 19 41 61 16 24 56 80 22 31
65 2.5591 80 3.1496 23 39 9 15 35 57 14 22 50 75 20 30 69 98 27 39
76
Self-Aligning Ball Bearings
77
78
Self-Aligning Ball Bearings
79
Self-Aligning Ball Bearings MRC Bearing Services
Mounting bearings with tapered apply to bearings with Normal seating. Guideline values for the
bore clearance. requisite displacement S are given
Bearings with a tapered bore are An easy method of mounting in the table overleaf.
always mounted with an interference bearings on adapter sleeves is When using either of the above
fit on the shaft, adapter sleeve or based on the tightening angle α methods, the self-aligning ball
withdrawal sleeve. As a measure through which the nut is turned and bearings should always be pushed
of the° of interference of the fit, either the procedure is described in the up on to the tapered seating until the
the reduction in radial internal following. Guideline values for the bore of the bearing is in contact with
clearance of the bearing or the axial tightening angle α are given in the the seating on the shaft or sleeve
displacement of the inner ring on the table overleaf. Before mounting, the around its whole circumference,
tapered bearing seating can be thread of the nut and the side face before the final tightening procedure
used. The mounting of self-aligning of the nut which is to abut the is begun. A sufficiently tight fit will
ball bearings with tapered bore calls bearing should be smeared with a then be obtained and the residual
for experience and skill molybdenum disulphide paste or clearance will correspond to the
as they have a relatively small similar lubricant, and the outside mean values given in the table.
internal clearance, and a reliable diameter of the sleeve should be One method of measuring the
measurement of the clearance lightly oiled. The bearing is then internal clearance of self-aligning
reduction is not always possible. pushed on to the sleeve and the ball bearings is shown in the
When mounting bearings with nut screwed on. By turning the nut illustrations below. A washer A is
Normal radial internal clearance it through the given angle α the inserted between the bearing and
is generally sufficient to check bearing will be pressed up on the the shaft or sleeve nut to ensure
clearance reduction during the tapered seating of the sleeve. As correct alignment of the outer ring
drive-up by turning and swivelling the bearing has a tendency to with respect to the inner ring. A dial
out the outer ring. When the bearing skew when being pressed up it is gauge B placed on the bearing
is properly mounted the outer ring advisable to reposition the hook outer ring can be used to measure
can be easily turned but there spanner in a slot at 180˚ to that used the bearing clearance. The outer
should be a slight resistance when for tightening and then apply a light ring should be pushed upwards in
the ring is swivelled out. The bearing hammer blow to the spanner. The the direction of the shaft.
will then have the requisite bearing will straighten up on its
interference fit. In some cases, seating. The nut is then removed,
however, the residual internal the locking washer inserted and the
clearance may be too small for the nut replaced, tightened and locked
application, and a bearing with C3 by bending down one of the tabs
radial internal clearance should be of the locking washer. The residual
used instead. clearance of the bearing should be
When mounting bearings with C3 checked.
clearance, the tightening angle α or Another method which is often
the axial displacement S can be used to mount bearings with a
used to measure the° of tapered bore correctly and reliably
interference. The procedures and is to measure the axial displacement
values given in the following also S of the inner ring on the tapered
80
Self-Aligning Ball Bearings
85 3.3465 120 .58 .023 .60 .024 .54 .021 .59 .023 20 8 40 16
90 3.5433 120 .58 .023 .60 .024 .54 .021 .59 .023 20 8 40 16
95 3.7402 120 .58 .023 .60 .024 .54 .021 .59 .023 20 8 40 16
100 3.9370 120 .58 .023 .60 .024 .54 .021 .59 .023 20 8 40 16
105 4.1339 120 .67 .026 — — .66 .026 — — 25 10 55 22
110 4.3307 120 .67 .026 .70 .028 .66 .026 .69 .027 25 10 55 22
81
82
5000 Series Double-Row
Angular Contact Ball Bearings
M-type
Maximum capacity double-row ball bearings have filling
notches on one side to permit assembling the
maximum number of balls into the bearing. Contact
angles converge outside the bearing. All inner and
outer rings have closure grooves. These bearings may
MRC double-row angular contact ball bearings are be equipped with seals, shields, and snap-rings. The
manufactured in two main types: C-type (Conrad M-type bearing has very heavy radial capacity. It also
construction) and M-type (maximum capacity with filling has thrust capacity in one direction, with the ability to
notches). Each of the two rows has a 30˚ contact angle. accommodate light thrust load in the reversing
C-type direction.
Part numbers on M-type double-row bearings are
Conrad construction, or C-type, double-row ball
normally located on either the side face or the O.D.
bearings have contact angles that converge outside
surface of the bearing.The side face marking is always
the bearing, thereby increasing resistance to
on the side opposite the filling notch and the O.D.
misalignment. This type does not have filling notches.
marking is offset from the center away from the filling
These bearings are recommended for applications
notch. Therefore, double sealed or shielded bearings
where single-row ball bearings are inadequate, but
with the filling notch covered from view can be oriented
radial loads are not so great as to suggest a filling-
correctly.
Ball Cages and Types
notch bearing. They will take heavy radial loads and
axial loads equally in either direction. The C-type
design fully meets the requirements of American
The cage supplied with C-type and M-type bearings is
Petroleum Institute (API) Specification 610.
a one-piece crown-type of heat-treated pressed steel. It
Both the inner and the outer rings have closure is snapped into place after the full quota of balls has
grooves. These bearings are available with seals, been introduced between the inner and outer ring.
shields, and snap-rings.
The older MRC 5000 series double-row ball greater rigidity than found in the previous double-
bearings were made in three series — 5200 Light, row filling-notch type bearings. A unique
5300 Medium, and 5400 Heavy — each with manufacturing system utilizing “common parts” is
progressively larger cross sections. These old-style employed in the manufacture of these bearings.
5000 type double-rows were available in the SB Using a minimum number of components, the
Conrad and maximum capacity configurations. system provides greater flexibility for producing
The SB Conrad version had contact angles which either Conrad or maximum capacity types as open
diverged inwardly, thereby increasing resistance bearings or with a variety of closures. Twenty-four
to misalignment. The maximum capacity version variations of a single bearing size can be
had contact angles which converged inwardly, manufactured to solve your application problems.
giving it the capability of handling small amounts
of misalignment. It also had filling notches on The chart on pages 85-86 outlines the suffixes and
both sides, for the introduction of a maximum widths of MRC 5000 series bearings. The data
complement of balls. on the chart do not represent actual availability of
double-row products. These data are intended to
Our double-row ball bearings are available in the be used as references for interchanging. Current
C-type (Conrad construction) and M-type (with style double-rows appear next to their old-style
filling notches on one side only). Both types feature counterparts that are the same width.
inwardly diverging contact angles, which provide
84
5000 Series Bearings Suffix and Width Summary
85
5000 Series Bearings Suffix and Width Summary MRC Bearing Services
86
Interchange to C- and M- Types
Double-Row Angular Contact Ball Bearings
Bearing numbers of MRC double-row ball bearings 5000 Series double-row bearings not listed here
produced before 1983 differ from the C- and M-types maintain the original bearing number and must be
listed in this catalog. Shown below is the interchange of specified by that number when ordering.
pre-1983 bearing numbers with the C- and M-types.
87
Filling Notch Location on
5000-MFF and 5000-MZZ Series MRC Bearing Services
Since the filling notch row is not visible on 5000MFF A typical application of a 5000MFF or 5000MZZ
and 5000MZZ bearings, it is necessary to identify bearing is shown above in which it is subjected to an
which row of balls has the notch in those cases axial load in an upward direction. The bearing should
where the bearing will be subjected to axial load. be mounted with the filling notch up so that the axial
Axial load should be carried on the non-filling notch load is taken by the bottom, non-filling notch row.
row. A moderate reversing axial load is permissible
on the filling notch row.
88
5000 Series Axial and Radial
Internal Clearance
10 .3937 1 11 0 4 5 21 2 8 12 28 5 11 25 45 10 18
10 .3937 18 7087 1 12 0 5 6 23 2 9 13 31 5 12 27 47 11 19
18 .7087 24 .9449 2 14 1 6 7 25 3 10 16 34 6 13 28 48 11 19
24 .9449 30 1.1811 2 15 1 6 8 27 3 11 18 37 7 15 30 50 12 20
30 1.1811 40 1.5748 2 16 1 6 9 29 4 11 21 40 8 16 33 54 13 21
40 1.5748 50 1.9685 2 18 1 7 11 33 4 13 23 44 9 17 36 58 14 23
50 1.9685 65 2.5591 3 22 1 9 13 36 5 14 26 48 10 19 40 63 16 25
65 2.5591 80 3.1496 3 24 1 9 15 40 6 16 30 54 12 21 46 71 18 28
80 3.1496 100 3.9370 3 26 1 10 18 46 7 18 35 63 14 25 55 83 22 33
5400 Series
Bore Diameter d Radial Internal Clearance
Over Including C2 Normal C0 C3 C4
.001 .0001 .001 .0001 .001 .0001 .001 .0001
mm in mm in mm in mm in
mm in mm in Min Max Min Max Min Max Min Max Min Max Min Max Min Max Min Max
30 1.1811 1 8 0.4 3 2 13 1 5 13 23 5 9 20 38 8 15
30 1.1811 40 1.5748 1 8 0.5 3 6 13 2 5 15 23 6 9 23 41 9 16
40 1.5748 50 1.9685 1 8 0.5 3 6 15 2 6 15 25 6 10 23 44 9 17
80 3.1496 90 3.5433 0 7 0 3 7 23 3 9 23 44 9 17 44 65 17 26
89
Thrust Rating of 5000 Series
Double-Row Angular Contact Ball Bearings MRC Bearing Services
Dynamic Rating Static Rating
To obtain dynamic thrust rating multiply dynamic radi- To obtain static thrust rating multiply static radial
al rating C by the factor shown below. rating C0 by the factor shown below.
Size Factor Size Factor
5200SB-5203SB 5200SB-5203SB
5300SB-5303SB 0.71 5300SB-5303SB
0.57
5403C-5414C 5204C&M-5206C&M
5204C&M-5218C&M 5403C-5414C
0.81
5304C&M-5319C&M 5207C&M-5218C&M
0.66
5304C&M-5319C&M
Example:
Bearing size: 5307C Example:
Basic dynamic radial load rating (C) =11100 lbf Bearing size: 5214M
Thrust rating factor = 0.81 Basic static radial load rating (C0) = 28100 lbf
Thrust rating = 0.81 × 11100 = 8991 lbf Thrust rating factor = 0.66
Thrust rating = 0.66 × 28100 = 18546 lbf
Sizes 5415C-5419C have 0˚ contact angles and are
not included in the above tables. When thrust load is
present, the equivalent radial load should be used to
determine life.
90
MRC Extra Wide 5000 Series
Double-Row Angular Contact Ball Bearing Retrofit Kit
Double-row angular contact ball bearings with non- locknut. If a locknut is used, the amount of clamping
standard extra wide width are currently available as force can be regulated to make slight adjustments in the
a retrofit kit. These replacement units consist of a shaft’s axial location. The spacer rings yield slightly
standard width double-row angular contact ball bearing when an axial clamping force is applied. The spacer
and two specially designed spacers packaged together rings also exert a reaction force, which helps maintain
in a single carton. the initial clamping force and helps prevent the inner
ring from becoming loose on the shaft. The same
Spacers circumstances apply to the outer ring spacers when an
The Extra Width Double-Row Angular Contact Ball end cap is used to clamp the bearing’s outer ring
Bearing Retrofit Kit is simple to use. When used with against a housing shoulder.
bearings without snap rings, place both spacers on
the same side, as shown in Figure 1. Because the spacer rings are designed to yield slightly
when axial clamping forces are applied, the spacer
With snap ring bearings, the inner ring spacer must be rings should always be replaced with new spacer rings
installed on the side opposite the snap ring, as shown in anytime the bearing is removed, replaced or reinstalled.
Figure 2. The outer spacer is not needed in applications
where the bearing’s snap ring controls the axial location Materials for Rings, Balls and Spacers
of the outer ring in the housing. High-carbon chromium vacuum-processed steel (SAE
52100) is used for all balls and rings. Machined and roll
The spacers accommodate slight variations in the shaft formed spacer rings are fabricated from 1018 carbon
and housing seat width. The inner ring and spacer can steel and 304 stainless steel.
be secured to the shaft with a retaining ring or threaded
91
Extra Wide 5000 Series
Part Numbers MRC Bearing Services
A listing of available part numbers appears below.
This listing may change with sizes being added or
deleted based on demand.
Inches mm
5205CF1 ⁷|₈ .8750 22.23
5205MF1 ⁷|₈ .8750 22.23
5206CF1 1¹|₁₆ 1.0625 26.99
5206MF1 1¹|₁₆ 1.0625 26.99
5206SBZZ* 1¹|₁₆ 1.0625 26.99
5212MF1 1¹|₂ 1.5000 38.10
5304CF1 1 1.0000 25.40
5304MF1 1 1.0000 25.40
5305CF1 1¹|₈ 1.1250 28.58
5305MFG1 1¹|₈ 1.1250 28.58
5306MFG1 1⁵|₁₆ 1.3125 33.34
5306MF1 1⁵|₁₆ 1.3125 33.34
5307MF1 1¹|₂ 1.5000 38.10
5307MFG1 1¹|₂ 1.5000 38.10
5308MFG1 1⁹|₁₆ 1.5625 39.69
5308MF1 1⁹|₁₆ 1.5625 39.69
5309MFG1 1¹¹|₁₆ 1.6875 42.86
5309MF1 1¹¹|₁₆ 1.6875 42.86
5310MFG1 1⁷|₈ 1.8750 47.63
5310MF1 1⁷|₈ 1.8750 47.63
5311MFG1 2¹|₁₆ 2.0625 52.39
5311MF1 2¹|₁₆ 2.0625 52.39
5312MFG1 2¹|₄ 2.2500 57.15
5312MF1 2¹|₄ 2.2500 57.15
5313MFG1 2⁷|₁₆ 2.4375 61.91
5313MF1 2⁷|₁₆ 2.4375 61.91
5315MF1 2¹³|₁₆ 2.8125 71.44
*Currently stocked. No spacer needed.
Nomenclature
5 3 09 M F G 1
Double-row angular contact type ball bearing
Series (200, 300, 400)
Bore diameter code
C or M (Conrad or Max type)
F or Z (Shield or Seal)
Snap ring
Extra width (Spacer ring kit supplied)
92
5200-C, 5200-SB Light Series
5200-C bearings are used with moderate to
heavy radial loads, two-directional thrust loads,
or a combination of both.
5200-SB 10 .3937 30 1.1811 14.29 .5625 .64 .025 7 610 1 710 4 300 967 16 000 22 000 16 000
5201-SB 12 .4724 32 1.2598 15.88 .6250 .64 .025 10 400 2 340 5 600 1 260 15 000 20 000 15 000
5202-SB 15 .5906 35 1.3780 15.88 .6250 .64 .025 11 400 2 560 6 800 1 530 12 000 17 000 12 000
5203-SB 17 .6693 40 1.5748 17.47 .6876 .64 .025 14 300 3 210 8 800 1 980 10 000 15 000 10 000
5204-C 20 .7874 47 1.8504 20.64 .8125 1.0 .04 19 000 4 270 12 000 2 700 9 000 13 000 9 000
5205-C 25 .9843 52 2.0472 20.64 .8125 1.0 .04 20 800 4 680 14 000 3 150 8 000 11 000 8 000
5205-C1 25 .9843 52 2.0472 22.23 .8750 1.0 .04 20 800 4 680 14 000 3 150 8 000 11 000 8 000
5206-C 30 1.1811 62 2.4409 23.81 .9375 1.0 .04 28 600 6 430 20 400 4 590 7 000 9 500 7 000
5206-C1 30 1.1811 62 2.4409 26.99 1.0625 1.0 .04 28 600 6 430 20 400 4 590 7 000 9 500 7 000
5207-C 35 1.3780 72 2.8346 26.99 1.0625 1.0 .04 37 700 8 480 27 500 6 180 6 000 8 000 6 000
5207-C1 35 1.3780 72 2.8346 30.16 1.1875 1.0 .04 37 700 8 480 27 500 6 180 6 000 8 000 6 000
5208-C 40 1.5748 80 3.1496 30.16 1.1875 1.0 .04 44 900 10 100 34 000 7 640 5 600 7 500 5 600
5209-C 45 1.7717 85 3.3465 30.16 1.1875 1.0 .04 48 800 11 000 39 000 8 770 5 000 6 700 5 000
5210-C 50 1.9685 90 3.5433 30.16 1.1875 1.0 .04 48 800 11 000 39 000 8 770 4 800 6 300 4 800
5211-C 55 2.1654 100 3.9370 33.34 1.3125 1.5 .06 57 200 12 900 47 500 10 700 4 300 5 600 4 300
5212-C 60 2.3622 110 4.3307 36.51 1.4375 1.5 .06 70 200 15 800 58 500 13 200 3 800 5 000 3 800
5212-C1 60 2.3622 110 4.3307 38.10 1.5000 1.5 .06 70 200 15 800 58 500 13 200 3 800 5 000 3 800
5213-C 65 2.5591 120 4.7244 38.10 1.5000 1.5 .06 80 600 18 100 73 500 16 500 3 600 4 800 3 600
5214-C 70 2.7559 125 4.9213 39.69 1.5625 1.5 .06 88 400 19 900 80 000 18 000 3 200 4 300 3 200
5215-C 75 2.9528 130 5.1181 41.28 1.6250 1.5 .06 95 600 21 500 88 000 19 800 3 200 4 300 3 200
5216-C 80 3.1496 140 5.5118 44.45 1.7500 2.0 .08 106 000 23 900 95 000 21 400 2 800 3 800 2 800
5217-C 85 3.3465 150 5.9055 49.21 1.9375 2.0 .08 124 000 27 900 110 000 24 700 2 600 3 600 2 600
5218-C 90 3.5433 160 6.2992 52.39 2.0625 2.0 .08 130 000 29 300 120 000 27 000 2 400 3 400 2 400
5219-C 95 3.7402 170 6.6929 55.56 2.1875 2.0 .08 159 000 35 700 146 000 32 800 2 200 3 200 2 200
5220-C 100 3.9370 180 7.0866 60.33 2.3750 2.0 .08 178 000 40 000 166 000 37 300 2 000 3 000 2 000
5221-C 105 4.1339 190 7.4803 65.09 2.5625 2.0 .08 186 000 41 800 180 000 40 500 1 800 2 800 1 800
5222-C 110 4.3307 200 7.8740 69.85 2.7500 2.0 .08 203 000 45 600 200 000 45 000 1 600 2 600 1 600
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2) Listed values are for pressed steel cage, ABEC-1.
The values have been determined through historical application and practice. For a more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
Note: Extra width bearings identified by the suffix C1 are supplied with a retrofit kit described on pages 91, 92.
93
5300-C, 5300-SB Medium Series MRC Bearing Services
5300-C bearings are used with heavy radial loads, two-
directional thrust loads, or a combination of both.
5300-SB 10 .3937 35 1.3780 19.05 .7500 .64 .025 10 600 2 380 6 100 1 370 15 000 20 000 15 000
5301-SB 12 .4724 37 1.4567 19.05 .7500 1.0 .04 11 700 2 630 6 800 1 530 14 000 18 000 14 000
5302-SB 15 .5906 42 1.6535 19.05 .7500 1.0 .04 15 100 3 390 9 300 2 090 11 000 15 000 11 000
5303-SB 17 .6693 47 1.8504 22.23 .8750 1.0 .04 21 600 4 860 12 700 2 860 11 000 14 000 11 000
5304-C 20 .7874 52 2.0472 22.23 .8750 1.0 .04 22 500 5 060 14 600 3 280 8 500 12 000 8 500
5304-C1 20 .7874 52 2.0472 25.40 1.0000 1.0 .04 22 500 5 060 14 600 3 280 8 500 12 000 8 500
5305-C 25 .9843 62 2.4409 25.40 1.0000 1.0 .04 30 700 6 910 20 400 4 590 7 500 10 000 7 500
5306-C 30 1.1811 72 2.8346 30.16 1.1875 1.0 .04 41 600 9 360 29 000 6 520 6 300 8 500 6 300
5306-C1 30 1.1811 72 2.8346 33.34 1.3125 1.0 .04 41 600 9 360 29 000 6 520 6 300 8 500 6 300
5307-C 35 1.3780 80 3.1496 34.93 1.3750 1.5 .06 49 400 11 100 34 500 7 760 5 600 7 500 5 600
5307-C1 35 1.3780 80 3.1496 38.10 1.5000 1.5 .06 49 400 11 100 34 500 7 760 5 600 7 500 5 600
5308-C 40 1.5748 90 3.5433 36.51 1.4375 1.5 .06 60 500 13 600 43 000 9 760 5 000 6 700 5 000
5308-C1 40 1.5748 90 3.5433 39.69 1.5625 1.5 .06 60 500 13 600 43 000 9 760 5 000 6 700 5 000
5309-C 45 1.7717 100 3.9370 39.69 1.5625 1.5 .06 72 800 16 400 53 000 11 900 4 500 6 000 4 500
5309-C1 45 1.7717 100 3.9370 42.86 1.6875 1.5 .06 72 800 16 400 53 000 11 900 4 500 6 000 4 500
5310-C 50 1.9685 110 4.3307 44.45 1.7500 2.0 .08 85 200 19 200 64 000 14 400 4 000 5 300 4 000
5310-C1 50 1.9685 110 4.3307 47.63 1.8750 2.0 .08 85 200 19 200 64 000 14 400 4 000 5 300 4 000
5311-C 55 2.1654 120 4.7244 49.21 1.9375 2.0 .08 106 000 23 900 81 500 18 300 3 800 5 000 3 800
5311-C1 55 2.1654 120 4.7244 52.39 2.0625 2.0 .08 106 000 23 900 81 500 18 300 3 800 5 000 3 800
5312-C 60 2.3622 130 5.1181 53.98 2.1250 2.0 .08 121 000 27 200 95 000 21 400 3 400 4 500 3 400
5312-C1 60 2.3622 130 5.1181 57.15 2.2500 2.0 .08 121 000 27 200 95 000 21 400 3 400 4 500 3 400
5313-C 65 2.5591 140 5.5118 58.74 2.3125 2.0 .08 138 000 31 100 108 000 24 300 3 200 4 300 3 200
5313-C1 65 2.5591 140 5.5118 61.91 2.4375 2.0 .08 138 000 31 100 108 000 24 300 3 200 4 300 3 200
5314-C 70 2.7559 150 5.9055 63.50 2.5000 2.0 .08 153 000 34 400 125 000 28 100 2 800 3 800 2 800
5314-C1 70 2.7559 150 5.9055 66.68 2.6250 2.0 .08 153 000 34 400 125 000 28 100 2 800 3 800 2 800
5315-C 75 2.9528 160 6.2992 68.26 2.6875 2.0 .08 168 000 37 800 140 000 31 500 2 600 3 600 2 600
5315-C1 75 2.9528 160 6.2992 71.44 2.8125 2.0 .08 168 000 37 800 140 000 31 500 2 600 3 600 2 600
5316-C 80 3.1496 170 6.6929 68.26 2.6875 2.0 .08 182 000 41 000 156 000 35 100 2 400 3 400 2 400
5317-C 85 3.3465 180 7.0866 73.03 2.8750 2.5 .10 195 000 43 900 176 000 39 600 2 200 3 200 2 200
5318-C 90 3.5433 190 7.4803 73.03 2.8750 2.5 .10 212 000 47 700 196 000 44 100 2 000 3 000 2 000
5319-C 95 3.7402 200 7.8740 77.79 3.0625 2.5 .10 234 000 52 700 224 000 50 400 1 900 2 800 1 900
5320-C 100 3.9370 215 8.4646 82.55 3.2500 2.5 .10 255 000 57 300 255 000 57 300 1 800 2 600 1 800
5322-C 110 4.3307 240 9.4488 92.08 3.6250 2.5 .10 291 000 65 400 305 000 68 600 1 700 2 400 1 700
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2) Listed values are for pressed steel cage, ABEC-1.
The values have been determined through historical application and practice. For a more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
Note: Extra width bearings identified by the suffix C1 are supplied with a retrofit kit described on pages 91, 92.
94
5400-C Heavy Series
5406C 30 1.1811 90 3.5433 39.69 1.5625 1.5 .06 67 600 15 200 45 000 10 100 5 300 7 000
5407C 35 1.3780 100 3.9370 44.45 1.7500 1.5 .06 76 100 17 000 49 000 11 000 4 800 6 300
5408C 40 1.5748 110 4.3307 49.21 1.9375 2.0 .08 88 400 19 900 57 000 12 800 4 300 5 600
5409C 45 1.7717 120 4.7244 53.98 2.1250 2.0 .08 112 000 25 200 78 000 17 600 4 000 5 300
5410C 50 1.9685 130 5.1181 58.74 2.3125 2.0 .08 143 000 32 200 102 000 23 000 3 600 4 800
5411C 55 2.1654 140 5.5118 63.50 2.5000 2.0 .08 146 000 32 900 102 000 23 000 3 200 4 300
5412C 60 2.3622 150 5.9055 66.68 2.6250 2.0 .08 159 000 35 800 114 000 25 700 3 000 4 000
5413C 65 2.5591 160 6.2992 71.44 2.8125 2.0 .08 195 000 43 900 156 000 35 100 2 800 3 800
5414C 70 2.7559 180 7.0866 79.38 3.1250 2.5 .10 199 000 44 800 156 000 35 100 2 400 3 400
5415C 75 2.9528 190 7.4803 82.55 3.2500 2.5 .10 212 000 47 700 200 000 45 000 2 200 3 200
5416C 80 3.1496 200 7.8740 87.31 3.4375 2.5 .10 229 000 51 500 216 000 48 600 2 000 3 000
5417C 85 3.3465 210 8.2677 92.08 3.6250 3.0 .12 255 000 57 300 255 000 57 300 1 900 2 800
5418C 90 3.5433 225 8.8583 98.43 3.8750 3.0 .12 281 000 63 200 300 000 67 400 1 800 2 600
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2) Listed values are for pressed steel cage, ABEC-1.
The values have been determined through historical application and practice. For a more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
95
5200-M Light Series MRC Bearing Services
5200M bearings are used with heavy radial loads, two-
directional thrust loads, or a combination of both. Thrust
load should be carried on the non-filling notch row.
Moderate thrust load is permissible on the filling notch row.
5204-M 20 .7874 47 1.8504 20.64 .8125 1.0 .04 20 500 4 610 17 000 3 820 9 000 13 000 9 000
5205-M 25 .9843 52 2.0472 20.64 .8125 1.0 .04 22 900 5 150 21 200 4 770 8 000 11 000 8 000
5205-M1 25 .9843 52 2.0472 22.23 .8750 1.0 .04 22 900 5 150 21 200 4 770 8 000 11 000 8 000
5206-M 30 1.1811 62 2.4409 23.81 .9375 1.0 .04 30 300 6 820 28 000 6 290 7 000 9 500 7 000
5206-M1 30 1.1811 62 2.4409 26.99 1.0625 1.0 .04 30 300 6 820 28 000 6 290 7 000 9 500 7 000
5207-M 35 1.3780 72 2.8346 26.99 1.0625 1.0 .04 39 100 8 800 36 500 8 210 6 000 8 000 6 000
5207-M1 35 1.3780 72 2.8346 30.16 1.1875 1.0 .04 39 100 8 800 36 500 8 210 6 000 8 000 6 000
5208-M 40 1.5748 80 3.1496 30.16 1.1875 1.0 .04 49 500 11 100 49 000 11 000 5 600 7 500 5 600
5209-M 45 1.7717 85 3.3465 30.16 1.1875 1.0 .04 51 200 11 500 54 000 12 100 5 000 6 700 5 000
5210-M 50 1.9685 90 3.5433 30.16 1.1875 1.0 .04 53 900 12 100 58 500 13 200 4 800 6 300 4 800
5211-M 55 2.1654 100 3.9370 33.34 1.3125 1.5 .06 66 000 14 900 76 500 17 200 4 300 5 600 4 300
5212-M 60 2.3622 110 4.3307 36.51 1.4375 1.5 .06 78 100 17 600 88 000 19 800 3 800 5 000 3 800
5212-M1 60 2.3622 110 4.3307 38.10 1.5000 1.5 .06 78 100 17 600 88 000 19 800 3 800 5 000 3 800
5213-M 65 2.5591 120 4.7244 38.10 1.5000 1.5 .06 88 000 19 800 106 000 23 800 3 600 4 800 3 600
5214-M 70 2.7559 125 4.9213 39.69 1.5625 1.5 .06 101 000 22 700 125 000 28 100 3 200 4 300 3 200
5215-M 75 2.9528 130 5.1181 41.28 1.6250 1.5 .06 108 000 24 300 137 000 30 800 3 200 4 300 3 200
5216-M 80 3.1496 140 5.5118 44.45 1.7500 2.0 .08 128 000 28 800 160 000 36 000 2 800 3 800 2 800
5217-M 85 3.3465 150 5.9055 49.21 1.9375 2.0 .08 142 000 32 000 176 000 39 600 2 600 3 600 2 600
5218-M 90 3.5433 160 6.2992 52.39 2.0625 2.0 .08 151 000 34 000 193 000 43 400 2 400 3 400 2 400
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2) Listed values are for pressed steel cage, ABEC-1.
The values have been determined through historical application and practice. For a more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
Note: Extra width bearings identified by the suffix M1 are supplied with a retrofit kit described on pages 91, 92.
96
5300-M Medium Series
5300M bearings are used with heavy radial loads, two-
directional thrust loads, or a combination of both. Thrust
load should be carried on the non-filling notch row.
Moderate thrust load is permissible on the filling notch row.
5304-M 20 .7874 52 2.0472 22.23 .8750 1.0 .04 23 800 5 360 20 000 4 500 8 500 12 000 8 500
5304-M1 20 .7874 52 2.0472 25.40 1.0000 1.0 .04 23 800 5 360 20 000 4 500 8 500 12 000 8 500
5305-M 25 .9843 62 2.4409 25.40 1.0000 1.0 .04 34 100 7 670 30 500 6 860 7 500 10 000 7 500
5306-M 30 1.1811 72 2.8346 30.16 1.1875 1.0 .04 46 800 10 500 43 000 9 670 6 300 8 500 6 300
5306-M1 30 1.1811 72 2.8346 33.34 1.3125 1.0 .04 46 800 10 500 43 000 9 670 6 300 8 500 6 300
5307-M 35 1.3780 80 3.1496 34.93 1.3750 1.5 .06 52 300 11 800 48 000 10 800 5 600 7 500 5 600
5307-M1 35 1.3780 80 3.1496 38.10 1.5000 1.5 .06 52 300 11 800 48 000 10 800 5 600 7 500 5 600
5308-M 40 1.5748 90 3.5433 36.51 1.4375 1.5 .06 67 100 15 100 65 500 14 700 5 000 6 700 5 000
5308-M1 40 1.5748 90 3.5433 39.69 1.5625 1.5 .06 67 100 15 100 65 500 14 700 5 000 6 700 5 000
5309-M 45 1.7717 100 3.9370 39.69 1.5625 1.5 .06 80 900 18 200 80 000 18 000 4 500 6 000 4 500
5309-M1 45 1.7717 100 3.9370 42.86 1.6875 1.5 .06 80 900 18 200 80 000 18 000 4 500 6 000 4 500
5310-M 50 1.9685 110 4.3307 44.45 1.7500 2.0 .08 95 200 21 400 95 000 21 400 4 000 5 300 4 000
5310-M1 50 1.9685 110 4.3307 47.63 1.8750 2.0 .08 95 200 21 400 95 000 21 400 4 000 5 300 4 000
5311-M 55 2.1654 120 4.7244 49.21 1.9375 2.0 .08 119 000 26 800 122 000 27 400 3 800 5 000 3 800
5311-M1 55 2.1654 120 4.7244 52.39 2.0625 2.0 .08 119 000 26 800 122 000 27 400 3 800 5 000 3 800
5312-M 60 2.3622 130 5.1181 53.98 2.1250 2.0 .08 134 000 30 200 143 000 32 100 3 400 4 500 3 400
5312-M1 60 2.3622 130 5.1181 57.15 2.2500 2.0 .08 134 000 30 200 143 000 32 100 3 400 4 500 3 400
5313-M 65 2.5591 140 5.5118 58.74 2.3125 2.0 .08 154 000 34 700 163 000 36 600 3 200 4 300 3 200
5313-M1 65 2.5591 140 5.5118 61.91 2.4375 2.0 .08 154 000 34 700 163 000 36 600 3 200 4 300 3 200
5314-M 70 2.7559 150 5.9055 63.50 2.5000 2.0 .08 172 000 38 700 186 000 41 800 2 800 3 800 2 800
5314-M1 70 2.7559 150 5.9055 66.68 2.6250 2.0 .08 172 000 38 700 186 000 41 800 2 800 3 800 2 800
5315-M 75 2.9528 160 6.2992 68.26 2.6875 2.0 .08 187 000 42 000 208 000 46 800 2 600 3 600 2 600
5315-M1 75 2.9528 160 6.2992 71.44 2.8125 2.0 .08 187 000 42 000 208 000 46 800 2 600 3 600 2 600
5316-M 80 3.1496 170 6.6929 68.26 2.6875 2.0 .08 201 000 45 200 236 000 53 100 2 400 3 400 2 400
5317 85 3.3465 180 7.0866 73.03 2.8750 2.5 .10 198 000 44 500 245 000 55 100 2 200 3 200 2 200
5318 90 3.5433 190 7.4803 73.03 2.8750 2.5 .10 224 000 50 400 290 000 65 200 2 000 3 000 2 000
5319 95 3.7402 200 7.8740 77.79 3.0625 2.5 .10 242 000 54 400 315 000 70 800 1 900 2 800 1 900
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
Listed values are for pressed steel cage, ABEC-1.
The values have been determined through historical application and practice. For a more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
Note: Extra width bearings identified by the suffix M1 are supplied with a retrofit kit described on pages 91, 92.
97
5300-UPG Series Double-Row
Angular Contact Ball Bearings MRC Bearing Services
5308UPG 40 1.5748 90 3.5433 36.51 1.4375 1.5 0.06 49 400 11 110 41 500 9 330 5 000 6 700
5309UPG 45 1.7717 100 3.9370 39.69 1.5625 1.5 0.06 61 800 13 890 52 000 11 690 4 500 6 000
5310UPG 50 1.9685 110 4.3307 44.45 1.7500 2.0 0.08 81 900 18 410 69 500 15 620 4 000 5 300
5311UPG 55 2.1654 120 4.7244 49.21 1.9375 2.0 0.08 95 600 21 490 83 000 18 660 3 800 5 000
5313UPG 65 2.5591 140 5.5118 58.74 2.3125 2.1 0.08 138 000 31 000 122 000 27 400 3 200 4 300
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2) Rating for one million revolutions or 500 hours at 331/ 3 RPM.
98
5000 Series Double-Row
Angular Contact Ball Bearings
P = XFR + YFA P = Dynamic equivalent radial P0 = X0FR + Y0FA P0 = Static equivalent radial load
load FR = Radial load
FR = Radial load FA = Thrust load
FA = Thrust load X0 = Radial load factor
X = Radial load factor Y0 = Thrust load factor
Y = Thrust load factor
C0 = Basic static radial load rating
e = Limiting factor for FA/FR
Size X0 Y0
99
5000 Series Double-Row
Angular Contact Ball Bearings MRC Bearing Services
Dynamic equivalent radial load
and life calculation examples
Bearing size: 5210 M Bearing size: 5203 SB
Speed: 2000 RPM Speed: 2000 RPM
Basic dynamic radial load rating (C) = 12100 Basic dynamic radial load rating (C) = 3210
Case 1 Case 1
Radial load (FR) = 1750 Radial load (FR) = 500
FA/FR = 0/1750 = 0 FA/FR = 0/500 = 0
Equivalent load (P) = X FR + Y FA Equivalent load (P) = X FR + Y FA
Since FA/FR < e, equivalent load Since FA/FR < e, equivalent load
(P) = 1.0 FR + 0.78 FA = 1.0 × 1750 = 1750 (P) = 1.0 FR + 0.92 FA = 1.0 × 500 = 500
3 3 3 3
12100 3210
() (
Life (L10) = C =
P 1750 ) = 331 × 106 Rev. () (
Life (L10) = C =
P 500 ) = 265 × 106 Rev.
or 6 3 6
12100
3 or 6 3 6
3210
3
()
10 C 10
Life (L10h) = 60n P = 60 × 2000 1750 ( ) ()
10 C 10
Life (L10h) = 60n P = 60 × 2000 500 ( )
= 2755 Hrs = 2205 Hrs
Case 2 Case 2
Radial load (FR) = 1750 Radial load (FR) = 500
Thrust load (FA) = 1300 Thrust load (FA) = 325
FA/FR = 1300/1750 = 0.74 FA/FR = 325/500 = 0.65
Equivalent load (P) = X FR + Y FA Equivalent load (P) = X FR + Y FA
Since FA/FR < e, equivalent load Since FA/FR < e, equivalent load
(P) = 1.0 FR + 0.78 FA = 1.0 × 1750 + 0.78 × 1300= 2764 (P) = 1.0 FR + 0.92 FA = 1.0 × 500 + 0.92 × 325= 799
3 3 3 3
12100 3210
() (
Life (L10) = C =
P 2764) = 83.9 × 106 Rev. () (
Life (L10) = C =
P 799 ) = 64.8 × 106 Rev.
or 6 3 6
12100
3 or 6 3 6
3210
3
()
10 C 10
Life (L10h) = 60n P = 60 × 2000 2764 ( ) ()
10 C 10
Life (L10h) = 60n P = 60 × 2000 799 ( )
= 699 Hrs = 540 Hrs
Case 3 Case 3
Radial load (FR) = 1750 Radial load (FR) = 500
Thrust load (FA) = 1500 Thrust load (FA) = 375
FA/FR = 1500/1750 = 0.86 FA/FR = 375/500 = 0.75
Equivalent load (P) = X FR + Y FA Equivalent load (P) = X FR + Y FA
Since FA/FR > e, equivalent load Since FA/FR > e, equivalent load
(P) = 0.63 FR + 1.24 FA (P) = 0.67 FR + 1.41 FA
= 0.63 × 1750 + 1.24 × 1500 = 2963 = 0.67 × 500 + 1.41 × 375 = 864
3 3 3 3
12100 3210
() (
Life (L10) = C =
P 2963 ) = 68.1 × 106 Rev. () (
Life (L10) = C =
P 864 ) = 51.3 × 106 Rev.
or 6 3 6
12100
3 or 6 3 6
3210
3
()
10 C 10
Life (L10h) = 60n P = 60 × 2000 2963 ( ) ()
10 C 10
Life (L10h) = 60n P = 60 × 2000 864 ( )
= 568 Hrs = 427 Hrs
Case 4 Case 4
Thrust load (FA) = 1500 Thrust load (FA) = 375
FA/FR = 1500/0 = ∞ FA/FR = 375/0 = ∞
Equivalent load (P) = X FR + Y FA Equivalent load (P) = X FR + Y FA
Since FA/FR > e, equivalent load Since FA/FR > e, equivalent load
(P) = 0.63 FR + 1.24 FA = 1.24 × 1500 = 1860 (P) = 0.67 FR + 1.41 FA = 1.41 × 375 = 529
3 3 3 3
12100 3210
() (
Life (L10) = C =
P 1860 ) = 275 × 106 Rev. () (
Life (L10) = C =
P 529 ) = 223 × 106 Rev.
or 6 3 6
12100
3 or 6 3 6
3210
3
()
10 C 10
Life (L10h) = 60n P = 60 × 2000 1860 ( ) ()
10 C 10
Life (L10h) = 60n P = 60 × 2000 529 ( )
= 2294 Hrs = 1862 Hrs
100
101
102
R-Type Single-Row 15°
Angular Contact Ball Bearings
MRC R-type bearings are single-row 15° angular Cage Types and Materials
contact ball bearings with one heavy race shoulder
and one counterbored race shoulder on the outer Cage types and materials available are: two-piece
ring. Because of this construction, it is possible to pressed steel, ball-riding, bent prong cages;
incorporate a greater number of balls than in the one-piece machined brass, inner ring-riding cages;
deep-groove nonfilling notch bearing. R-type and one-piece phenolic (bakelite), inner ring-riding
bearings have ample radial capacity and moderate cages.
thrust capacity in order to accomodate those
applications involving heavy radial loads; some
thrust load; or a combination of both.
103
1900-R Extremely Light Series
(Single Bearings) MRC Bearing Services
1900-R 10 .3937 22 .8661 6 .2362 .30 .012 .10 .004 110 .17 3 120 701 1 560 351 33 000 40 000
1901-R 12 .4724 24 .9449 6 .2362 .30 .012 .10 .004 123 .19 3 250 731 1 800 405 30 000 36 000
1902-R 15 .5906 28 1.1024 7 .2756 .30 .012 .10 .004 187 .29 4 880 1 100 2 700 607 24 000 30 000
1903-R 17 .6693 30 1.1811 7 .2756 .30 .012 .10 .004 206 .32 5 400 1 210 3 000 674 22 000 28 000
1904-R 20 .7874 37 1.4567 9 .3543 .30 .012 .15 .006 400 .62 9 360 2 100 5 850 1 320 18 000 22 000
1905-R 25 .9843 42 1.6535 9 .3543 .30 .012 .15 .006 342 .53 7 610 1 710 5 300 1 190 16 000 19 000
1906-R 30 1.1811 47 1.8504 9 .3543 .30 .012 .15 .006 452 .70 9 750 2 190 7 100 1 600 14 000 17 000
1907-R 35 1.3780 55 2.1654 10 .3937 .64 .025 .15 .006 555 .86 11 200 2 520 9 000 2 020 11 000 14 000
1908-R 40 1.5748 62 2.4409 12 .4724 .64 .025 .15 .006 722 1.12 14 300 3 210 11 600 2 600 10 000 15 000
1909-R 45 1.7717 68 2.6772 12 .4724 .64 .025 .15 .006 806 1.25 15 100 3 400 13 400 3 010 9 000 11 000
1910-R 50 1.9685 72 2.8346 12 .4724 .64 .025 .15 .006 1 070 1.66 19 500 4 380 17 300 3 900 8 500 10 000
1911-R 55 2.1654 80 3.1496 13 .5118 1.0 .04 .30 .012 1 260 1.95 22 900 5 150 20 400 4 590 8 000 9 500
1912-R 60 2.3622 85 3.3465 13 .5118 1.0 .04 .30 .012 1 390 2.15 24 200 5 440 22 800 5 130 7 500 9 000
1913-R 65 2.5591 90 3.5433 13 .5118 1.0 .04 .30 .012 1 450 2.25 24 700 5 550 24 000 5 400 6 700 8 000
1914-R 70 2.7559 100 3.9370 16 .6299 1.0 .04 .30 .012 1 990 3.09 33 200 7 460 32 500 7 300 6 300 7 500
1915-R 75 2.9528 105 4.1339 16 .6299 1.0 .04 .30 .012 2 080 3.23 34 500 7 760 34 500 7 760 6 000 7 000
1916-R 80 3.1496 110 4.3307 16 .6299 1.0 .04 .30 .012 2 180 3.38 34 500 7 760 36 000 8 100 5 600 6 700
1917-R 85 3.3465 120 4.7244 18 .7087 1.0 .04 .60 .024 2 840 4.40 44 900 10 100 46 500 10 500 5 300 6 300
1918-R 90 3.5433 125 4.9213 18 .7087 1.0 .04 .60 .024 3 400 5.27 52 700 11 800 56 000 12 600 5 000 6 000
1919-R 95 3.7402 130 5.1181 18 .7087 1.0 .04 .60 .024 3 090 4.79 47 500 10 700 52 000 11 700 4 800 5 600
1920-R 100 3.9370 140 5.5118 20 .7874 1.0 .04 .60 .024 3 870 6.00 58 500 13 200 64 000 14 400 4 500 5 300
1921-R 105 4.1339 145 5.7087 20 .7874 1.0 .04 .60 .024 4 030 6.25 60 500 13 600 67 000 15 100 4 300 5 000
1922-R 110 4.3307 150 5.9055 20 .7874 1.0 .04 .60 .024 3 820 5.93 55 300 12 400 64 000 14 400 4 000 4 800
1924-R 120 4.7244 165 6.4961 22 .8661 1.0 .04 .60 .024 5 100 7.91 74 100 16 700 85 000 19 100 3 600 4 300
1926-R 130 5.1181 180 7.0866 24 .9449 1.5 .06 .60 .024 6 300 9.77 90 400 20 500 106 000 23 800 3 400 4 000
1928-R 140 5.5118 190 7.4803 24 .9449 1.5 .06 .60 .024 6 580 10.2 95 600 21 400 110 000 24 700 3 200 3 800
1930-R 150 5.9055 210 8.2677 28 1.1024 2.0 .08 1.0 .040 9 090 14.1 125 000 28 200 150 000 33 700 2 800 3 400
1932-R 160 6.2992 220 8.6614 28 1.1024 2.0 .08 1.0 .040 9 420 14.6 127 000 28 600 156 000 35 100 2 600 3 200
1934-R 170 6.6929 230 9.0551 28 1.1024 2.0 .08 1.0 .040 10 200 15.8 133 000 29 800 170 000 38 300 2 400 3 000
1936-R 180 7.0866 250 9.8425 33 1.2992 2.0 .08 1.0 .040 12 800 19.9 168 000 36 000 212 000 47 800 2 200 2 800
1938-R 190 7.4803 260 10.2362 33 1.2992 2.0 .08 1.0 .040 13 400 20.7 174 000 39 100 224 000 50 400 2 200 2 800
1940-R 200 7.8740 280 11.0236 38 1.4961 2.0 .08 1.0 .040 16 800 26.0 216 100 48 600 275 000 61 800 2 000 2 600
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
Listed values are for pressed steel or polyamide cage, ABEC-1.
For phenolic composition cage, multiply by 1.66 for grease and 2.00 for oil. For machined bronze cage, multiply by 1.25 for grease and 1.50 for oil. For phenolic composition
cage, ABEC-5 or 7, multiply by 2.30 for grease and 2.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
104
1900-RD Extremely Light Series
Duplex
“D” indicates a duplex ground half pair matched with an identical half pair
and is followed by an additional suffix letter to describe the type of duplex.
See pages 234 and 235 for suffix description.
Note: ABEC 1 & 3 are stocked as half-pairs where available. Use these values for back-to-back (DB) or face-to-face (DF) mounting arrangements.
1900-RD 10 .3937 22 .8661 12 .4724 .30 .012 .10 .004 110 .17 5 070 1 140 3 100 697 26 000 32 000
1901-RD 12 .4724 24 .9449 12 .4724 .30 .012 .10 .004 123 .19 5 270 1 180 3 550 798 24 000 29 000
1902-RD 15 .5906 28 1.1024 14 .5512 .30 .012 .10 .004 187 .29 7 930 1 780 5 400 1 210 19 000 24 000
1903-RD 17 .6693 30 1.1811 14 .5512 .30 .012 .10 .004 206 .32 8 710 1 960 6 100 1 370 18 000 22 000
1904-RD 20 .7874 37 1.4567 18 .7087 .30 .012 .15 .006 400 .62 15 300 3 440 11 600 2 600 14 000 18 000
1905-RD 25 .9843 42 1.6535 18 .7087 .30 .012 .15 .006 342 .53 12 400 2 790 10 800 2 430 13 000 15 000
1906-RD 30 1.1811 47 1.8504 18 .7087 .30 .012 .15 .006 452 .70 15 900 3 580 14 300 3 210 11 000 14 000
1907-RD 35 1.3780 55 2.1654 20 .7874 .64 .025 .15 .006 555 .86 18 200 4 090 18 000 4 050 8 800 11 000
1908-RD 40 1.5748 62 2.4409 24 .9449 .64 .025 .15 .006 722 1.12 22 900 5 150 23 200 5 220 8 000 10 000
1909-RD 45 1.7717 68 2.6772 24 .9449 .64 .025 .15 .006 806 1.25 24 700 5 550 26 500 5 960 7 200 8 800
1910-RD 50 1.9685 72 2.8346 24 .9449 .64 .025 .15 .006 1 070 1.66 31 900 7 170 34 500 7 760 6 800 8 000
1911-RD 55 2.1654 80 3.1496 26 1.0236 1.0 .04 .30 .012 1 260 1.95 37 100 8 340 40 500 9 100 6 400 7 600
1912-RD 60 2.3622 85 3.3465 26 1.0236 1.0 .04 .30 .012 1 390 2.15 39 000 8 770 45 500 10 200 6 000 7 200
1913-RD 65 2.5591 90 3.5433 26 1.0236 1.0 .04 .30 .012 1 450 2.25 39 700 8 920 48 000 10 800 5 400 6 400
1914-RD 70 2.7559 100 3.9370 32 1.2598 1.0 .04 .30 .012 1 990 3.09 54 000 12 100 65 500 14 700 5 000 6 000
1915-RD 75 2.9528 105 4.1339 32 1.2598 1.0 .04 .30 .012 2 080 3.23 55 900 12 600 68 000 15 300 4 800 5 600
1916-RD 80 3.1496 110 4.3307 32 1.2598 1.0 .04 .30 .012 2 180 3.38 57 200 12 900 72 000 16 200 4 500 5 400
1917-RD 85 3.3465 120 4.7244 36 1.4173 1.0 .04 .60 .024 2 840 4.40 74 100 16 700 93 000 20 900 4 200 5 000
1918-RD 90 3.5433 125 4.9213 36 1.4173 1.0 .04 .60 .024 3 400 5.27 85 200 19 200 112 000 25 200 4 000 4 800
1919-RD 95 3.7402 130 5.1181 36 1.4173 1.0 .04 .60 .024 3 090 4.79 76 100 17 100 104 000 23 400 3 800 4 500
1920-RD 100 3.9370 140 5.5118 40 1.5748 1.0 .04 .60 .024 3 870 6.00 95 600 21 500 127 000 28 600 3 600 4 200
1921-RD 105 4.1339 145 5.7087 40 1.5748 1.0 .04 .60 .024 4 030 6.25 97 500 21 900 134 000 30 100 3 400 4 000
1922-RD 110 4.3307 150 5.9055 40 1.5748 1.0 .04 .60 .024 3 820 5.93 90 400 20 300 129 000 29 000 3 200 3 800
1924-RD 120 4.7244 165 6.4961 44 1.7323 1.0 .04 .60 .024 5 100 7.91 121 000 27 200 170 000 38 200 2 900 3 400
1926-RD 130 5.1181 180 7.0866 48 1.8898 1.5 .06 .60 .024 6 300 9.77 146 000 32 800 208 000 46 800 2 700 3 200
1928-RD 140 5.5118 190 7.4803 48 1.8898 1.5 .06 .60 .024 6 580 10.2 156 000 35 100 220 000 49 500 2 600 3 000
1930-RD 150 5.9055 210 8.2677 56 2.2047 2.0 .08 1.0 .040 9 090 14.1 203 000 45 600 300 000 67 400 2 200 2 700
1932-RD 160 6.2992 220 8.6614 56 2.2047 2.0 .08 1.0 .040 9 420 14.6 208 000 46 800 315 000 70 800 2 100 2 600
1934-RD 170 6.6929 230 9.0551 56 2.2047 2.0 .08 1.0 .040 10 200 15.8 216 000 48 600 340 000 76 400 1 900 2 400
1936-RD 180 7.0866 250 9.8425 66 2.5984 2.0 .08 1.0 .040 12 800 19.9 276 000 62 000 425 000 95 600 1 800 2 200
1938-RD 190 7.4803 260 10.2362 66 2.5984 2.0 .08 1.0 .040 13 400 20.7 281 000 63 200 440 000 98 900 1 800 2 200
1940-RD 200 7.8740 280 11.0236 76 2.9921 2.0 .08 1.0 .040 16 800 26.0 351 000 78 900 550 000 124 000 1 600 2 100
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
Listed values are for pressed steel or polyamide cage, ABEC-1.
For phenolic composition cage, multiply by 1.66 for grease and 2.00 for oil. For machined bronze cage, multiply by 1.25 for grease and 1.50 for oil. For phenolic composition
cage, ABEC-5 or 7, multiply by 2.30 for grease and 2.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
105
100-R and 100-RD
Extra Large Series MRC Bearing Services
“D” indicates a duplex ground half pair matched with an identical half pair
and is followed by an additional suffix letter to describe the type of duplex.
See pages 234 and 235 for suffix description.
Note: ABEC 1 & 3 are stocked as half-pairs where available. Values for -RD bearings are for back-to-back (DB) or face-to-face (DF) mounting arrange-
ments.
Basic Radial Load Rating Speed Rating2)
MRC Bore Outside Width Fillet Radius 1)
120-R 100 3.9370 160 6.2992 28 1.1024 2.0 .08 1.0 .040 6 100 9.45 95 600 21 500 95 000 21 400 3 900 4 800
122-R 110 4.3307 175 6.8898 30 1.1811 2.0 .08 1.0 .040 7 290 11.3 114 000 25 600 114 000 25 600 3 600 4 400
124-R 120 4.7244 190 7.4803 32 1.2598 2.0 .08 1.0 .040 8 970 13.9 134 000 30 100 140 000 31 500 3 300 4 000
126-R 130 5.1181 205 8.0709 34 1.3386 2.0 .08 1.0 .040 9 350 14.5 138 000 31 000 150 000 33 700 3 000 3 700
128-R 140 5.5118 220 8.6614 36 1.4173 2.0 .08 1.0 .040 10 800 16.8 157 000 35 300 173 000 38 900 2 800 3 400
130-R 150 5.9055 235 9.2520 38 1.4961 2.0 .08 1.0 .040 12 400 19.3 176 000 39 600 200 000 45 000 2 600 3 200
132-R 160 6.2992 250 9.8425 40 1.5748 2.0 .08 1.0 .040 14 200 22.0 183 000 41 100 228 000 51 300 2 500 3 000
134-R 170 6.6929 265 10.4331 42 1.6535 2.5 .10 1.0 .040 16 000 24.8 216 000 48 600 255 000 57 300 2 300 2 800
136-R 180 7.0866 280 11.0236 44 1.7323 2.5 .10 1.0 .040 17 900 27.8 233 000 52 400 285 000 64 100 2 100 2 600
138-R 190 7.4803 300 11.8110 46 1.8110 2.5 .10 1.0 .040 22 200 34.4 275 000 61 800 355 000 79 800 2 100 2 500
140-R 200 7.8740 320 12.5984 48 1.8898 2.5 .10 1.0 .040 24 400 37.9 292 000 65 600 390 000 87 700 1 900 2 300
142-R 210 8.2677 340 13.3858 50 1.9685 2.5 .10 1.0 .040 28 000 43.4 319 000 71 700 440 000 98 900 1 800 2 200
144-R 220 8.6614 350 13.7795 51 2.0079 2.5 .10 1.0 .040 29 300 45.5 336 000 75 500 465 000 105 000 1 700 2 100
146-R 230 9.0551 370 14.5669 53 2.0866 3.0 .12 1.0 .040 31 900 49.5 352 000 79 100 510 000 115 000 1 600 2 000
148-R 240 9.4488 390 15.3543 55 2.1654 3.0 .12 1.0 .040 34 600 53.7 374 000 84 100 550 000 124 000 1 600 1 900
150-R 250 9.8425 410 16.1417 57 2.2441 3.0 .12 1.0 .040 37 500 58.1 393 000 88 400 600 000 135 000 1 500 1 800
152-R 260 10.2362 430 16.9291 59 2.3228 3.0 .12 1.0 .040 40 400 62.7 413 000 92 800 655 000 147 000 1 400 1 700
156-R 280 11.0236 460 18.1102 63 2.4803 3.0 .12 1.0 .040 46 600 72.3 457 000 103 000 750 000 169 000 1 300 1 600
164-R 320 12.5984 500 19.6850 71 2.7953 3.0 .12 1.0 .040 56 800 88.0 523 000 118 000 900 000 202 000 1 100 1 400
100-RD
120-RD 100 3.9370 160 6.2992 56 2.2047 2.0 .08 1.0 .040 6 100 9.45 156 000 35 100 190 000 42 700 3 100 3 800
122-RD 110 4.3307 175 6.8898 60 2.3622 2.0 .08 1.0 .040 7 290 11.3 185 000 41 800 228 000 51 300 2 900 3 500
124-RD 120 4.7244 190 7.4803 64 2.5197 2.0 .08 1.0 .040 8 970 13.9 221 000 49 700 280 000 62 900 2 600 3 200
126-RD 130 5.1181 205 8.0709 68 2.6772 2.0 .08 1.0 .040 9 350 14.5 221 000 49 700 300 000 67 400 2 400 3 000
128-RD 140 5.5118 220 8.6614 72 2.8346 2.0 .08 1.0 .040 10 800 16.8 255 000 57 300 345 000 77 600 2 200 2 700
130-RD 150 5.9055 235 9.2520 76 2.9921 2.0 .08 1.0 .040 12 400 19.3 286 000 64 300 400 000 89 900 2 100 2 600
132-RD 160 6.2992 250 9.8425 80 3.1496 2.0 .08 1.0 .040 14 200 22.0 296 000 66 500 455 000 102 000 2 000 2 400
134-RD 170 6.6929 265 10.4331 84 3.3071 2.5 .10 1.0 .040 16 000 24.8 351 000 78 900 510 000 115 000 1 800 2 200
136-RD 180 7.0866 280 11.0236 88 3.4646 2.5 .10 1.0 .040 17 900 27.8 377 000 84 800 570 000 128 000 1 700 2 100
138-RD 190 7.4803 300 11.8110 92 3.6220 2.5 .10 1.0 .040 22 200 34.4 442 000 99 400 710 000 160 000 1 700 2 000
140-RD 200 7.8740 320 12.5984 96 3.7795 2.5 .10 1.0 .040 24 400 37.9 475 000 107 000 780 000 175 000 1 500 1 800
142-RD 210 8.2677 340 13.3858 100 3.9370 2.5 .10 1.0 .040 28 000 43.4 527 000 118 000 880 000 198 000 1 400 1 800
144-RD 220 8.6614 350 13.7795 102 4.0157 2.5 .10 1.0 .040 29 300 45.5 540 000 121 000 930 000 209 000 1 400 1 700
146-RD 230 9.0551 370 14.5669 106 4.1732 3.0 .12 1.0 .040 31 900 49.5 572 000 129 000 1 020 000 229 000 1 300 1 600
148-RD 240 9.4488 390 15.3543 110 4.3307 3.0 .12 1.0 .040 34 600 53.7 605 000 136 000 1 100 000 247 000 1 300 1 500
150-RD 250 9.8425 410 16.1417 114 4.4882 3.0 .12 1.0 .040 37 500 58.1 637 000 143 000 1 200 000 270 000 1 200 1 400
152-RD 260 10.2362 430 16.9291 118 4.6457 3.0 .12 1.0 .040 40 400 62.7 676 000 152 000 1 290 000 290 000 1 100 1 400
156-RD 280 11.0236 460 18.1102 126 4.9606 3.0 .12 1.0 .040 46 600 72.3 741 000 167 000 1 500 000 337 000 1 000 1 300
164-RD 320 12.5984 500 19.6850 142 5.5906 3.0 .12 1.0 .040 56 800 88.0 852 000 192 000 1 800 000 405 000 880 1 100
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2) Listed values are for pressed steel or polyamide cage, ABEC-1.
For phenolic composition cage, multiply by 1.66 for grease and 2.00 for oil. For machined bronze cage, multiply by 1.25 for grease and 1.50 for oil. For phenolic composition
cage, ABEC-5 or 7, multiply by 2.30 for grease and 2.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
106
100-KR Extra Light Series
(Single Bearings)
100-KR 10 .3937 26 1.0236 8 .3150 .30 .012 .10 .004 181 .28 4 940 1 110 2 280 513 30 000 36 000
101-KR 12 .4724 28 1.1024 8 .3150 .30 .012 .10 .004 206 .32 5 530 1 240 2 650 596 26 000 32 000
102-KR 15 .5906 32 1.2598 9 .3543 .30 .012 .10 .004 226 .35 6 050 1 350 3 150 708 22 000 28 000
103-KR 17 .6693 35 1.3780 10 .3937 .30 .012 .10 .004 342 .53 8 520 1 920 4 650 1 050 19 000 24 000
104-KR 20 .7874 42 1.6535 12 .4724 .64 .025 .30 .012 445 .69 10 800 2 420 6 200 1 390 17 000 20 000
105-KR 25 .9843 47 1.8504 12 .4724 .64 .025 .30 .012 522 .81 12 100 2 720 7 650 1 720 15 000 18 000
106-KR 30 1.1811 55 2.1654 13 .5118 1.0 .04 .30 .012 716 1.11 15 600 3 500 10 600 2 380 12 000 15 000
107-KR 35 1.3780 62 2.4409 14 .5512 1.0 .04 .30 .012 884 1.37 18 600 4 180 13 200 2 970 10 000 13 000
108-KR 40 1.5748 68 2.6772 15 .5906 1.0 .04 .30 .012 942 1.46 19 500 4 380 14 600 3 280 9 500 12 000
109-KR 45 1.7717 75 2.9528 16 .6299 1.0 .04 .30 .012 1 220 1.89 24 200 5 440 19 000 4 270 9 000 11 000
110-KR 50 1.9685 80 3.1496 16 .6299 1.0 .04 .30 .012 1 300 2.01 25 100 5 640 20 400 4 590 8 500 10 000
111-KR 55 2.1654 90 3.5433 18 .7087 1.0 .04 .60 .024 1 810 2.81 33 800 7 600 28 000 6 290 7 500 9 000
112-KR 60 2.3622 95 3.7402 18 .7087 1.0 .04 .60 .024 1 920 2.97 35 100 7 890 30 000 6 740 6 700 8 000
113-KR 65 2.5591 100 3.9370 18 .7087 1.0 .04 .60 .024 2 030 3.14 35 800 8 050 32 500 7 310 6 300 7 500
114-KR 70 2.7559 110 4.3307 20 .7874 1.0 .04 .60 .024 2 470 3.83 42 300 9 510 40 000 8 990 6 000 7 000
115-KR 75 2.9528 115 4.5276 20 .7874 1.0 .04 .60 .024 2 590 4.02 43 600 9 800 42 500 9 550 5 600 6 770
116-KR 80 3.1496 125 4.9213 22 .8661 1.0 .04 .60 .024 3 390 5.25 55 900 12 600 54 000 12 100 5 300 6 300
117-KR 85 3.3465 130 5.1181 22 .8661 1.0 .04 .60 .024 3 550 5.50 57 200 12 900 57 000 12 800 5 000 6 000
118-KR 90 3.5433 140 5.5118 24 .9449 1.5 .06 .60 .024 4 280 6.64 68 900 15 500 68 000 15 300 4 800 5 600
119-KR 95 3.7402 145 5.7087 24 .9449 1.5 .06 .60 .024 5 040 7.81 83 200 18 700 80 000 18 000 4 500 5 300
120-KR 100 3.9370 150 5.9055 24 .9449 1.5 .06 .60 .024 4 700 7.28 71 500 16 100 76 500 17 200 4 300 5 000
121-KR 105 4.1339 160 6.2992 26 1.0236 2.0 .08 1.0 .040 5 540 8.59 85 200 19 200 90 000 20 200 4 000 4 800
122-KR 110 4.3307 170 6.6929 28 1.1024 2.0 .08 1.0 .040 6 400 9.93 99 500 22 400 102 000 23 000 3 800 4 500
124-KR 120 4.7244 180 7.0866 28 1.1024 2.0 .08 1.0 .040 6 710 10.4 101 000 22 600 110 000 24 700 3 400 4 000
126-KR 130 5.1181 200 7.8740 33 1.2992 2.0 .08 1.0 .040 9 350 14.5 138 000 31 000 150 000 33 700 3 200 3 800
128-KR 140 5.5118 210 8.2677 33 1.2992 2.0 .08 1.0 .040 9 350 14.5 135 000 30 300 153 000 34 400 3 000 3 600
130-KR 150 5.9055 225 8.8583 35 1.3780 2.0 .08 1.0 .040 10 800 16.8 156 000 35 000 176 000 39 600 2 600 3 200
132-KR 160 6.2992 240 9.4488 38 1.4961 2.0 .08 1.0 .040 12 400 19.3 178 000 40 000 204 000 45 900 2 400 3 000
134-KR 170 6.6929 260 10.2362 42 1.6535 2.0 .08 1.0 .040 15 300 23.7 212 000 47 700 245 000 55 100 2 200 2 800
136-KR 180 7.0866 280 11.0236 46 1.8110 2.0 .08 1.0 .040 17 900 27.8 234 000 52 600 290 000 65 200 2 000 2 600
138-KR 190 7.4803 290 11.4173 46 1.8110 2.0 .08 1.0 .040 18 800 29.1 242 000 54 400 305 000 68 600 2 000 2 600
140-KR 200 7.8740 310 12.2047 51 2.0079 2.0 .08 1.0 .040 22 200 34.4 276 000 62 000 355 000 79 800 1 900 2 400
144-KR 220 8.6614 340 13.3858 56 2.2047 2.5 .10 1.0 .040 30 400 47.2 345 000 77 600 480 000 108 000 1 800 2 200
148-KR 240 9.4488 360 14.1732 56 2.2047 2.5 .10 1.0 .040 31 900 49.5 351 000 78 900 510 000 115 000 1 700 2 000
152-KR 260 10.2362 400 15.7480 65 2.5591 3.0 .12 1.5 .060 41 500 64.3 423 000 95 100 655 000 147 000 1 500 1 800
156-KR 280 11.0236 420 16.5354 65 2.5591 3.0 .12 1.5 .060 43 500 67.4 436 000 98 000 695 000 156 000 1 400 1 700
160-KR 300 11.8110 460 18.1102 74 2.9134 3.0 .12 1.5 .060 54 200 84.0 520 000 117 000 850 000 191 000 1 200 1 500
164-KR 320 12.5984 480 18.8976 74 2.9134 3.0 .12 1.5 .060 56 800 88.0 527 000 118 000 900 000 202 000 1 100 1 400
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
Listed values are for pressed steel or polyamide cage, ABEC-1.
For phenolic composition cage, multiply by 1.66 for grease and 2.00 for oil. For machined bronze cage, multiply by 1.25 for grease and 1.50 for oil. For phenolic composition
cage, ABEC-5 or 7, multiply by 2.30 for grease and 2.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
107
100-KRD Extra Light Series
Duplex MRC Bearing Services
“D” indicates a duplex ground half pair matched with an identical half pair
and is followed by an additional suffix letter to describe the type of duplex
See pages 234 and 235 for suffix description.
Use these values for back-to-back (DB) or face-to-face (DF) mounting arrangements
Note: ABEC 1 & 3 are stocked as half-pairs where available
100-KRD 10 .3937 26 1.0236 16 .6299 .30 .012 .10 .004 181 .28 8 060 1 810 4 550 1 020 24 000 29 000
101-KRD 12 .4724 28 1.1024 16 .6299 .30 .012 .10 .004 206 .32 8 840 1 990 5 300 1 190 21 000 26 000
102-KRD 15 .5906 32 1.2598 18 .7087 .30 .012 .10 .004 226 .35 9 750 2 190 6 300 1 420 18 000 22 000
103-KRD 17 .6693 35 1.3780 20 .7874 .30 .012 .10 .004 342 .53 13 800 3 100 9 300 2 090 15 000 19 000
104-KRD 20 .7874 42 1.6535 24 .9449 .64 .025 .30 .012 445 .69 17 400 3 910 12 500 2 810 14 000 16 000
105-KRD 25 .9843 47 1.8504 24 .9449 .64 .025 .30 .012 522 .81 19 500 4 380 15 300 3 440 12 000 14 000
106-KRD 30 1.1811 55 2.1654 26 1.0236 1.0 .04 .30 .012 716 1.11 25 500 5 730 21 200 4 760 9 600 12 000
107-KRD 35 1.3780 62 2.4409 28 1.1024 1.0 .04 .30 .012 884 1.37 30 200 6 790 26 500 5 960 8 000 10 000
108-KRD 40 1.5748 68 2.6772 30 1.1811 1.0 .04 .30 .012 942 1.46 31 900 7 170 29 000 6 520 7 600 9 600
109-KRD 45 1.7717 75 2.9528 32 1.2598 1.0 .04 .30 .012 1 220 1.89 39 000 8 770 37 500 8 430 7 200 8 800
110-KRD 50 1.9685 80 3.1496 32 1.2598 1.0 .04 .30 .012 1 300 2.01 40 300 9 060 40 500 9 100 6 800 8 000
111-KRD 55 2.1654 90 3.5433 36 1.4173 1.0 .04 .60 .024 1 810 2.81 55 300 12 400 56 000 12 600 6 000 7 200
112-KRD 60 2.3622 95 3.7402 36 1.4173 1.0 .04 .60 .024 1 920 2.97 55 900 12 600 61 000 13 700 5 400 6 400
113-KRD 65 2.5591 100 3.9370 36 1.4173 1.0 .04 .60 .024 2 030 3.14 58 500 13 200 64 000 14 400 5 000 6 000
114-KRD 70 2.7559 110 4.3307 40 1.5748 1.0 .04 .60 .024 2 470 3.83 68 900 15 500 80 000 18 000 4 800 5 600
115-KRD 75 2.9528 115 4.5276 40 1.5748 1.0 .04 .60 .024 2 590 4.02 70 200 15 800 85 000 19 100 4 500 5 400
116-KRD 80 3.1496 125 4.9213 44 1.7323 1.0 .04 .60 .024 3 390 5.25 90 400 20 300 110 000 24 700 4 200 5 000
117-KRD 85 3.3465 130 5.1181 44 1.7323 1.0 .04 .60 .024 3 550 5.50 92 300 20 700 116 000 26 100 4 000 4 800
118-KRD 90 3.5433 140 5.5118 48 1.8898 1.5 .06 .60 .024 4 280 6.64 111 000 25 000 137 000 30 800 3 800 4 500
119-KRD 95 3.7402 145 5.7087 48 1.8898 1.5 .06 .60 .024 5 040 7.81 135 000 30 300 160 000 36 000 3 600 4 200
120-KRD 100 3.9370 150 5.9055 48 1.8898 1.5 .06 .60 .024 4 700 7.28 117 000 26 300 153 000 34 400 3 400 4 000
121-KRD 105 4.1339 160 6.2992 52 2.0472 2.0 .08 1.0 .040 5 540 8.59 138 000 31 000 180 000 40 500 3 200 3 800
122-KRD 110 4.3307 170 6.6929 56 2.2047 2.0 .08 1.0 .040 6 400 9.93 163 000 36 600 204 000 45 900 3 000 3 600
124-KRD 120 4.7244 180 7.0866 56 2.2047 2.0 .08 1.0 .040 6 710 10.4 163 000 36 600 220 000 49 500 2 700 3 200
126-KRD 130 5.1181 200 7.8740 66 2.5984 2.0 .08 1.0 .040 9 350 14.5 225 000 50 000 300 000 67 400 2 600 3 000
128-KRD 140 5.5118 210 8.2677 66 2.5984 2.0 .08 1.0 .040 9 350 14.5 221 000 49 700 305 000 68 600 2 400 2 900
130-KRD 150 5.9055 225 8.8583 70 2.7559 2.0 .08 1.0 .040 10 800 16.8 255 000 57 300 355 000 79 800 2 100 2 600
132-KRD 160 6.2992 240 9.4488 76 2.9921 2.0 .08 1.0 .040 12 400 19.3 286 000 64 300 405 000 91 000 1 900 2 400
134-KRD 170 6.6929 260 10.2362 84 3.3071 2.0 .08 1.0 .040 15 300 23.7 345 000 77 600 490 000 110 000 1 800 2 200
136-KRD 180 7.0866 280 11.0236 92 3.6220 2.0 .08 1.0 .040 17 900 27.8 377 000 84 800 570 000 128 000 1 600 2 100
138-KRD 190 7.4803 290 11.4173 92 3.6220 2.0 .08 1.0 .040 18 800 29.1 390 000 87 700 610 000 137 000 1 600 2 100
140-KRD 200 7.8740 310 12.2047 102 4.0157 2.0 .08 1.0 .040 22 200 34.4 442 000 99 400 710 000 160 000 1 500 1 900
144-KRD 220 8.6614 340 13.3858 112 4.4094 2.5 .10 1.0 .040 30 400 47.2 559 000 126 000 965 000 217 000 1 400 1 800
148-KRD 240 9.4488 360 14.1732 112 4.4094 2.5 .10 1.0 .040 31 900 49.5 572 000 129 000 1 020 000 228 000 1 400 1 600
152-KRD 260 10.2362 400 15.7480 130 5.1181 3.0 .12 1.5 .060 41 500 64.3 702 000 158 000 1 320 000 297 000 1 200 1 400
156-KRD 280 11.0236 420 16.5354 130 5.1181 3.0 .12 1.5 .060 43 500 67.4 715 000 161 000 1 400 000 315 000 1 100 1 400
160-KRD 300 11.8110 460 18.1102 148 5.8268 3.0 .12 1.5 .060 54 200 84.0 832 000 187 000 1 700 000 382 000 960 1 200
164-KRD 320 12.5984 480 18.8976 148 5.8268 3.0 .12 1.5 .060 56 800 88.0 852 000 192 000 1 810 000 406 000 880 1 100
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
Listed values are for pressed steel or polyamide cage, ABEC-1.
For phenolic composition cage, multiply by 1.66 for grease and 2.00 for oil. For machined bronze cage, multiply by 1.25 for grease and 1.50 for oil. For phenolic composition
cage, ABEC-5 or 7, multiply by 2.30 for grease and 2.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
108
200-R Light Series
(Single Bearings)
200-R 10 .3937 30 1.1811 9 .3543 .64 .025 .30 .012 284 .44 7 280 1 640 3 200 719 24 000 30 000
201-R 12 .4724 32 1.2598 10 .3937 .64 .025 .30 .012 323 .50 8 190 1 840 3 900 877 22 000 28 000
202-R 15 .5906 35 1.3780 11 .4331 .64 .025 .30 .012 406 .63 9 750 2 190 5 100 1 150 19 000 24 000
203-R 17 .6693 40 1.5748 12 .4724 .64 .025 .30 .012 510 .79 12 100 2 720 6 550 1 470 17 000 20 000
204-R 20 .7874 47 1.8504 14 .5512 1.0 .04 .60 .024 613 .95 14 000 3 150 8 500 1 910 15 000 18 000
205-R 25 .9843 52 2.0472 15 .5906 1.0 .04 .60 .024 755 1.17 16 800 3 780 10 600 2 380 12 000 15 000
206-R 30 1.1811 62 2.4409 16 .6299 1.0 .04 .60 .024 884 1.37 19 000 4 270 12 900 2 910 10 000 13 000
207-R 35 1.3780 72 2.8346 17 .6693 1.0 .04 .60 .024 1 270 1.97 26 000 5 850 18 600 4 180 9 000 11 000
208-R 40 1.5748 80 3.1496 18 .7087 1.0 .04 .60 .024 1 730 2.68 34 500 7 760 25 000 5 620 8 500 10 000
209-R 45 1.7717 85 3.3465 19 .7480 1.0 .04 .60 .024 1 730 2.68 34 500 7 760 25 500 5 730 7 500 9 000
210-R 50 1.9685 90 3.5433 20 .7874 1.0 .04 .60 .024 1 970 3.06 37 700 8 480 30 000 6 740 7 000 8 500
211-R 55 2.1654 100 3.9370 21 .8268 1.5 .06 1.0 .040 2 860 4.43 54 000 12 100 41 500 9 330 6 300 7 500
212-R 60 2.3622 110 4.3307 22 .8661 1.5 .06 1.0 .040 3 260 5.06 59 200 13 300 49 000 11 000 6 000 7 000
213-R 65 2.5591 120 4.7244 23 .9055 1.5 .06 1.0 .040 4 030 6.25 60 500 13 600 58 500 13 200 5 300 6 300
214-R 70 2.7559 125 4.9213 24 .9449 1.5 .06 1.0 .040 4 530 7.03 78 000 17 500 68 000 15 300 5 000 6 000
215-R 75 2.9528 130 5.1181 25 .9843 1.5 .06 1.0 .040 5 190 8.04 88 400 19 900 76 500 17 200 4 800 5 600
216-R 80 3.1496 140 5.5118 26 1.0236 2.0 .08 1.0 .040 4 880 7.56 85 200 19 200 73 500 16 500 4 500 5 300
217-R 85 3.3465 150 5.9055 28 1.1024 2.0 .08 1.0 .040 6 170 9.56 104 000 23 400 93 000 20 900 4 300 5 000
218-R 90 3.5433 160 6.2992 30 1.1811 2.0 .08 1.0 .040 7 870 12.2 130 000 29 200 116 000 26 100 3 800 4 500
219-R 95 3.7402 170 6.6929 32 1.2598 2.0 .08 1.0 .040 8 390 13.0 138 000 31 000 125 000 28 000 3 600 4 300
220-R 100 3.9370 180 7.0866 34 1.3386 2.0 .08 1.0 .040 9 610 14.9 153 000 34 000 143 000 32 100 3 400 4 000
221-R 105 4.1339 190 7.4803 36 1.4173 2.0 .08 1.0 .040 10 300 16.0 168 000 37 800 153 000 34 400 3 200 3 800
222-R 110 4.3307 200 7.8740 38 1.4961 2.0 .08 1.0 .040 11 700 18.1 182 000 40 900 170 000 38 200 3 000 3 600
224-R 120 4.7244 215 8.4646 40 1.5748 2.0 .08 1.0 .040 13 000 20.2 199 000 44 700 193 000 43 300 2 800 3 400
226-R 130 5.1181 230 9.0551 40 1.5748 2.5 .10 1.0 .040 15 500 24.0 221 000 49 600 232 000 52 200 2 600 3 200
228-R 140 5.5118 250 9.8425 42 1.6535 2.5 .10 1.0 .040 17 200 26.6 238 000 53 500 260 000 58 500 2 400 2 900
230-R 150 5.9055 270 10.6299 45 1.7717 2.5 .10 1.0 .040 20 700 32.1 270 000 60 700 310 000 69 700 2 200 2 700
232-R 160 6.2992 290 11.4173 48 1.8898 2.5 .10 1.0 .040 24 600 38.2 307 000 69 000 365 000 82 100 2 100 2 500
234-R 170 6.6929 310 12.2047 52 2.0472 3.0 .12 1.0 .040 27 200 42.2 332 000 74 600 400 000 89 900 1 900 2 300
236-R 180 7.0866 320 12.5984 52 2.0472 3.0 .12 1.0 .040 29 000 44.9 345 000 77 600 430 000 96 700 1 800 2 200
238-R 190 7.4803 340 13.3858 55 2.1654 3.0 .12 1.0 .040 33 100 51.3 377 000 84 800 500 000 112 000 1 700 2 100
240-R 200 7.8740 360 14.1732 58 2.2835 3.0 .12 1.0 .040 35 500 55.1 390 000 87 700 540 000 121 000 1 600 2 000
242-R 210 8.2677 380 14.9606 61 2.4016 3.0 .12 1.0 .040 40 800 63.3 436 000 98 000 610 000 137 000 1 600 1 900
244-R 220 8.6614 400 15.7480 65 2.5591 3.0 .12 1.0 .040 43 900 68.0 462 000 104 000 655 000 147 000 1 500 1 800
246-R 230 9.0551 420 16.5354 68 2.6772 3.0 .12 1.0 .040 49 500 76.8 494 000 111 000 735 000 165 000 1 400 1 700
248-R 240 9.4488 440 17.3228 72 2.8346 3.0 .12 1.0 .040 55 500 86.1 540 000 121 000 830 000 187 000 1 300 1 600
250-R 250 9.8425 460 18.1102 76 2.9921 4.0 .16 1.5 .060 61 900 95.9 585 000 132 000 915 000 206 000 1 200 1 500
252-R 260 10.2362 480 18.8976 80 3.1496 4.0 .16 1.5 .060 68 400 106.0 624 000 140 000 1 020 000 229 000 1 100 1 400
256-R 280 11.0236 500 19.6850 80 3.1496 4.0 .16 1.5 .060 72 200 112.0 650 000 146 000 1 100 000 247 000 1 100 1 400
260-R 300 11.8110 540 21.2598 85 3.3465 4.0 .16 1.5 .060 80 000 124.0 689 000 155 000 1 220 000 274 000 1 100 1 300
264-R 320 12.5984 580 22.8346 92 3.6220 4.0 .16 1.5 .060 87 700 136.0 741 000 167 000 1 340 000 301 000 980 1 200
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2) Listed values are for pressed steel or polyamide cage, ABEC-1.
For phenolic composition cage, multiply by 1.66 for grease and 2.00 for oil. For machined bronze cage, multiply by 1.25 for grease and 1.50 for oil. For phenolic composition
cage, ABEC-5 or 7, multiply by 2.30 for grease and 2.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
109
200-RD Light Series
Duplex MRC Bearing Services
“D” indicates a duplex ground half pair matched with an identical half pair
and is followed by an additional suffix letter to describe the type of duplex
See pages 234 and 235 for suffix description.
Use these values for back-to-back (DB) or face-to-face (DF) mounting arrangements
Note: ABEC 1 & 3 are stocked as half-pairs where available
200-RD 10 .3937 30 1.1811 18 .7087 .64 .025 .30 .012 284 .44 11 900 2 680 6 400 1 440 19 000 24 000
201-RD 12 .4724 32 1.2598 20 .7874 .64 .025 .30 .012 323 .50 13 300 2 990 7 800 1 750 18 000 22 000
202-RD 15 .5906 35 1.3780 22 .8661 .64 .025 .30 .012 406 .63 15 900 3 570 10 200 2 290 15 000 19 000
203-RD 17 .6693 40 1.5748 24 .9449 .64 .025 .30 .012 510 .79 19 900 4 470 13 200 2 970 14 000 16 000
204-RD 20 .7874 47 1.8504 28 1.1024 1.0 .04 .60 .024 613 .95 22 900 5 140 17 000 3 820 12 000 14 000
205-RD 25 .9843 52 2.0472 30 1.1811 1.0 .04 .60 .024 755 1.17 27 600 6 200 21 200 4 770 9 600 12 000
206-RD 30 1.1811 62 2.4409 32 1.2598 1.0 .04 .60 .024 884 1.37 30 700 6 900 26 000 5 850 8 000 10 000
207-RD 35 1.3780 72 2.8346 34 1.3386 1.0 .04 .60 .024 1 270 1.97 42 300 9 510 37 500 8 430 7 200 8 800
208-RD 40 1.5748 80 3.1496 36 1.4173 1.0 .04 .60 .024 1 730 2.68 55 900 12 600 50 000 11 200 6 800 8 000
209-RD 45 1.7717 85 3.3465 38 1.4961 1.0 .04 .60 .024 1 730 2.68 55 900 12 600 51 000 11 500 6 000 7 200
210-RD 50 1.9685 90 3.5433 40 1.5748 1.0 .04 .60 .024 1 970 3.06 60 500 13 600 60 000 13 500 5 600 6 800
211-RD 55 2.1654 100 3.9370 42 1.6535 1.5 .06 1.0 .040 2 860 4.43 87 100 19 600 83 000 18 700 5 000 6 000
212-RD 60 2.3622 110 4.3307 44 1.7323 1.5 .06 1.0 .040 3 260 5.06 95 600 21 500 98 000 22 000 4 800 5 600
213-RD 65 2.5591 120 4.7244 46 1.8110 1.5 .06 1.0 .040 4 030 6.25 97 500 21 900 118 000 26 500 4 200 5 000
214-RD 70 2.7559 125 4.9213 48 1.8898 1.5 .06 1.0 .040 4 530 7.03 125 000 28 200 137 000 30 800 4 000 4 800
215-RD 75 2.9528 130 5.1181 50 1.9685 1.5 .06 1.0 .040 5 190 8.04 143 000 32 100 153 000 34 400 3 800 4 500
216-RD 80 3.1496 140 5.5118 52 2.0472 2.0 .08 1.0 .040 4 880 7.56 138 000 31 000 140 000 31 500 3 600 4 200
217-RD 85 3.3465 150 5.9055 56 2.2047 2.0 .08 1.0 .040 6 170 9.56 168 000 37 800 186 000 41 800 3 400 4 000
218-RD 90 3.5433 160 6.2992 60 2.3622 2.0 .08 1.0 .040 7 870 12.2 212 000 47 700 232 000 52 200 3 000 3 600
219-RD 95 3.7402 170 6.6929 64 2.5197 2.0 .08 1.0 .040 8 390 13.0 221 000 49 700 250 000 56 200 2 900 3 400
220-RD 100 3.9370 180 7.0866 68 2.6772 2.0 .08 1.0 .040 9 610 14.9 251 000 56 400 285 000 64 100 2 700 3 200
221-RD 105 4.1339 190 7.4803 72 2.8346 2.0 .08 1.0 .040 10 300 16.0 270 000 60 700 305 000 68 600 2 600 3 000
222-RD 110 4.3307 200 7.8740 76 2.9921 2.0 .08 1.0 .040 11 700 18.1 296 000 66 500 340 000 76 400 2 400 2 900
224-RD 120 4.7244 215 8.4646 80 3.1496 2.0 .08 1.0 .040 13 000 20.2 325 000 73 100 390 000 87 700 2 200 2 700
226-RD 130 5.1181 230 9.0551 80 3.1496 2.5 .10 1.0 .040 15 500 24.0 358 000 80 500 465 000 105 000 2 100 2 600
228-RD 140 5.5118 250 9.8425 84 3.3071 2.5 .10 1.0 .040 17 200 26.6 390 000 87 700 510 000 115 000 1 900 2 300
230-RD 150 5.9055 270 10.6299 90 3.5433 2.5 .10 1.0 .040 20 700 32.1 442 000 99 400 620 000 139 000 1 800 2 200
232-RD 160 6.2992 290 11.4173 96 3.7795 2.5 .10 1.0 .040 24 600 38.2 494 000 111 000 735 000 165 000 1 700 2 000
234-RD 170 6.6929 310 12.2047 104 4.0945 3.0 .12 1.0 .040 27 200 42.2 527 000 118 000 800 000 180 000 1 500 1 800
236-RD 180 7.0866 320 12.5984 104 4.0945 3.0 .12 1.0 .040 29 000 44.9 559 000 126 000 865 000 194 000 1 400 1 800
238-RD 190 7.4803 340 13.3858 110 4.3307 3.0 .12 1.0 .040 33 100 51.3 605 000 136 000 1 000 000 225 000 1 400 1 700
240-RD 200 7.8740 360 14.1732 116 4.5669 3.0 .12 1.0 .040 35 500 55.1 637 000 143 000 1 080 000 243 000 1 300 1 600
242-RD 210 8.2677 380 14.9606 122 4.8031 3.0 .12 1.0 .040 40 800 63.3 702 000 158 000 1 220 000 274 000 1 300 1 500
244-RD 220 8.6614 400 15.7480 130 5.1181 3.0 .12 1.0 .040 43 900 68.0 741 000 167 000 1 320 000 297 000 1 200 1 400
246-RD 230 9.0551 420 16.5354 136 5.3543 3.0 .12 1.0 .040 49 500 76.8 806 000 181 000 1 500 000 337 000 1 100 1 400
248-RD 240 9.4488 440 17.3228 144 5.6693 3.0 .12 1.0 .040 55 500 86.1 871 000 196 000 1 660 000 373 000 1 000 1 300
250-RD 250 9.8425 460 18.1102 152 5.9843 4.0 .16 1.5 .060 61 900 95.9 956 000 215 000 1 830 000 411 000 960 1 200
252-RD 260 10.2362 480 18.8976 160 6.2992 4.0 .16 1.5 .060 68 400 106.0 1 010 000 227 000 2 040 000 459 000 880 1 100
256-RD 280 11.0236 500 19.6850 160 6.2992 4.0 .16 1.5 .060 72 200 112.0 1 060 000 238 000 2 200 000 495 000 880 1 100
260-RD 300 11.8110 540 21.2598 170 6.6929 4.0 .16 1.5 .060 80 000 124.0 1 140 000 256 000 2 400 000 540 000 880 1 000
264-RD 320 12.5984 580 22.8346 184 7.2441 4.0 .16 1.5 .060 87 700 136.0 1 210 000 272 000 2 700 000 607 000 780 960
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2) Listed values are for pressed steel or polyamide cage, ABEC-1.
For phenolic composition cage, multiply by 1.66 for grease and 2.00 for oil. For machined bronze cage, multiply by 1.25 for grease and 1.50 for oil. For phenolic composition
cage, ABEC-5 or 7, multiply by 2.30 for grease and 2.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
110
300-R Medium Series
(Single Bearings)
301-R 12 .4724 37 1.4567 12 .4724 1.0 .04 .60 .024 439 .68 10 600 2 380 4 900 1 100 19 000 24 000
302-R 15 .5906 42 1.6535 13 .5118 1.0 .04 .60 .024 510 .79 12 100 2 720 6 550 1 470 17 000 20 000
303-R 17 .6693 47 1.8504 14 .5512 1.0 .04 .60 .024 632 .98 14 800 3 330 8 150 1 830 16 000 19 000
304-R 20 .7874 52 2.0472 15 .5906 1.0 .04 .60 .024 909 1.41 20 300 4 560 11 400 2 560 13 000 16 000
305-R 25 .9843 62 2.4409 17 .6693 1.0 .04 .60 .024 1 090 1.69 23 400 5 260 15 300 3 440 11 000 14 000
306-R 30 1.1811 72 2.8346 19 .7480 1.0 .04 .60 .024 1 480 2.30 31 200 7 010 20 000 4 500 9 000 11 000
307-R 35 1.3780 80 3.1496 21 .8268 1.5 .06 1.0 .040 1 940 3.00 39 700 8 920 26 000 5 850 8 500 10 000
308-R 40 1.5748 90 3.5433 23 .9055 1.5 .06 1.0 .040 2 450 3.80 48 800 11 000 33 500 7 530 7 500 9 000
309-R 45 1.7717 100 3.9370 25 .9843 1.5 .06 1.0 .040 3 030 4.69 58 500 13 200 40 500 9 100 6 700 8 000
310-R 50 1.9685 110 4.3307 27 1.0630 2.0 .08 1.0 .040 4 350 6.75 80 600 18 100 57 000 12 800 6 300 7 500
311-R 55 2.1654 120 4.7244 29 1.1417 2.0 .08 1.0 .040 5 110 7.92 93 600 21 000 67 000 15 100 5 600 6 700
312-R 60 2.3622 130 5.1181 31 1.2205 2.0 .08 1.0 .040 5 930 9.19 108 000 24 300 78 000 17 500 5 000 6 000
313-R 65 2.5591 140 5.5118 33 1.2992 2.0 .08 1.0 .040 6 900 10.7 121 000 27 200 93 000 20 900 4 800 5 600
314-R 70 2.7559 150 5.9055 35 1.3780 2.0 .08 1.0 .040 6 770 10.5 121 000 27 200 93 000 20 900 4 500 5 300
315-R 75 2.9528 160 6.2992 37 1.4567 2.0 .08 1.0 .040 9 030 14.0 153 000 34 400 122 000 27 400 4 300 5 000
316-R 80 3.1496 170 6.6929 39 1.5354 2.0 .08 1.0 .040 9 480 14.7 159 000 35 700 129 000 29 000 3 800 4 500
317-R 85 3.3465 180 7.0866 41 1.6142 2.5 .10 1.0 .040 11 400 17.7 182 000 40 900 156 000 35 100 3 600 4 300
318-R 90 3.5433 190 7.4803 43 1.6929 2.5 .10 1.0 .040 11 800 18.3 186 000 41 800 160 000 36 000 3 400 4 000
319-R 95 3.7402 200 7.8740 45 1.7717 2.5 .10 1.0 .040 13 100 20.3 199 000 44 700 180 000 40 500 3 200 3 800
320-R 100 3.9370 215 8.4646 47 1.8504 2.5 .10 1.0 .040 14 400 22.4 212 000 47 700 200 000 45 000 3 000 3 600
321-R 105 4.1339 225 8.8583 49 1.9291 2.5 .10 1.0 .040 15 900 24.6 229 000 51 500 204 000 45 900 2 800 3 400
322-R 110 4.3307 240 9.4488 50 1.9685 2.5 .10 1.0 .040 18 800 29.2 255 000 57 300 255 000 57 300 2 600 3 200
324-R 120 4.7244 260 10.2362 55 2.1654 2.5 .10 1.0 .040 22 100 34.3 265 000 59 600 300 000 67 400 2 500 3 000
326-R 130 5.1181 280 11.0236 58 2.2835 3.0 .12 1.0 .040 25 700 39.8 296 000 66 500 345 000 77 600 2 300 2 800
328-R 140 5.5118 300 11.8110 62 2.4409 3.0 .12 1.0 .040 29 500 45.7 351 000 78 900 400 000 89 900 2 100 2 600
330-R 150 5.9055 320 12.5984 65 2.5591 3.0 .12 1.0 .040 33 900 52.6 390 000 87 700 475 000 107 000 2 000 2 400
332-R 160 6.2992 340 13.3858 68 2.6772 3.0 .12 1.0 .040 38 400 59.6 423 000 95 100 530 000 119 000 1 800 2 200
334-R 170 6.6929 360 14.1732 72 2.8346 3.0 .12 1.0 .040 40 800 63.2 436 000 98 000 570 000 128 000 1 700 2 100
336-R 180 7.0866 380 14.9606 75 2.9528 3.0 .12 1.0 .040 45 700 70.9 475 000 107 000 640 000 144 000 1 600 2 000
338-R 190 7.4803 400 15.7480 78 3.0709 4.0 .16 1.5 .060 51 000 79.0 507 000 114 000 710 000 160 000 1 600 1 900
340-R 200 7.8740 420 16.5354 80 3.1496 4.0 .16 1.5 .060 56 400 87.5 553 000 124 000 780 000 175 000 1 500 1 800
342-R 210 8.2677 440 17.3228 84 3.3071 4.0 .16 1.5 .060 62 200 96.5 592 000 133 000 865 000 194 000 1 400 1 700
344-R 220 8.6614 460 18.1102 88 3.4646 4.0 .16 1.5 .060 68 400 106.0 637 000 143 000 950 000 214 000 1 300 1 600
348-R 240 9.4488 500 19.6850 95 3.7402 4.0 .16 1.5 .060 74 800 116.0 676 000 152 000 1 060 000 238 000 1 100 1 400
352-R 260 10.2362 540 21.2598 102 4.0157 5.0 .20 2.0 .080 87 100 135.0 741 000 167 000 1 250 000 281 000 1 100 1 300
356-R 280 11.0236 580 22.8346 108 4.2520 5.0 .20 2.0 .080102 000 158.0 832 000 187 000 1 460 000 328 000 980 1 200
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
Listed values are for pressed steel or polyamide cage, ABEC-1.
For phenolic composition cage, multiply by 1.66 for grease and 2.00 for oil. For machined bronze cage, multiply by 1.25 for grease and 1.50 for oil. For phenolic composition
cage, ABEC-5 or 7, multiply by 2.30 for grease and 2.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
111
300-RD Medium Series
Duplex MRC Bearing Services
“D” indicates a duplex ground half pair matched with an identical half pair
and is followed by an additional suffix letter to describe the type of duplex
See pages 234 and 235 for suffix description.
Note: ABEC 1 & 3 are stocked as half-pairs where available Use these values for back-to-back (DB) or face-to-face (DF) mounting arrangements
301-RD 12 .4724 37 1.4567 24 .9449 1.0 .04 .60 .024 439 .68 17 200 3 870 9 800 2 200 15 000 19 000
302-RD 15 .5906 42 1.6535 26 1.0236 1.0 .04 .60 .024 510 .79 19 900 4 470 13 200 2 970 14 000 16 000
303-RD 17 .6693 47 1.8504 28 1.1024 1.0 .04 .60 .024 632 .98 24 200 5 440 16 300 3 660 13 000 15 000
304-RD 20 .7874 52 2.0472 30 1.1811 1.0 .04 .60 .024 909 1.41 33 200 7 460 22 800 5 130 10 000 13 000
305-RD 25 .9843 62 2.4409 34 1.3386 1.0 .04 .60 .024 1 090 1.69 37 700 8 480 30 500 6 860 8 800 11 000
306-RD 30 1.1811 72 2.8346 38 1.4961 1.0 .04 .60 .024 1 480 2.30 50 700 11 400 40 000 8 990 7 200 8 800
307-RD 35 1.3780 80 3.1496 42 1.6535 1.5 .06 1.0 .040 1 940 3.00 65 000 14 600 52 000 11 700 6 800 8 000
308-RD 40 1.5748 90 3.5433 46 1.8110 1.5 .06 1.0 .040 2 450 3.80 79 300 17 800 67 000 15 100 6 000 7 200
309-RD 45 1.7717 100 3.9370 50 1.9685 1.5 .06 1.0 .040 3 030 4.69 95 600 21 500 81 500 18 300 5 400 6 400
310-RD 50 1.9685 110 4.3307 54 2.1260 2.0 .08 1.0 .040 4 350 6.75 133 000 29 900 114 000 25 600 5 000 6 000
311-RD 55 2.1654 120 4.7244 58 2.2835 2.0 .08 1.0 .040 5 110 7.92 153 000 34 400 134 000 30 100 4 500 5 400
312-RD 60 2.3622 130 5.1181 62 2.4409 2.0 .08 1.0 .040 5 930 9.19 174 000 39 100 156 000 35 100 4 000 4 800
313-RD 65 2.5591 140 5.5118 66 2.5984 2.0 .08 1.0 .040 6 900 10.7 195 000 43 800 190 000 42 700 3 800 4 500
314-RD 70 2.7559 150 5.9055 70 2.7559 2.0 .08 1.0 .040 6 770 10.5 195 000 43 800 186 000 41 800 3 600 4 200
315-RD 75 2.9528 160 6.2992 74 2.9134 2.0 .08 1.0 .040 9 030 14.0 247 000 55 500 245 000 55 100 3 400 4 000
316-RD 80 3.1496 170 6.6929 78 3.0709 2.0 .08 1.0 .040 9 480 14.7 260 000 58 500 260 000 58 500 3 000 3 600
317-RD 85 3.3465 180 7.0866 82 3.2283 2.5 .10 1.0 .040 11 400 17.7 291 000 65 400 310 000 67 400 2 900 3 400
318-RD 90 3.5433 190 7.4803 86 3.3858 2.5 .10 1.0 .040 11 800 18.3 302 000 67 900 320 000 71 900 2 700 3 200
319-RD 95 3.7402 200 7.8740 90 3.5433 2.5 .10 1.0 .040 13 100 20.3 325 000 73 100 360 000 80 900 2 600 3 000
320-RD 100 3.9370 215 8.4646 94 3.7008 2.5 .10 1.0 .040 14 400 22.4 345 000 77 600 400 000 89 900 2 400 2 900
321-RD 105 4.1339 225 8.8583 98 3.8583 2.5 .10 1.0 .040 15 900 24.6 371 000 83 400 405 000 91 000 2 200 2 700
322-RD 110 4.3307 240 9.4488 100 3.9370 2.5 .10 1.0 .040 18 800 29.2 416 000 93 500 510 000 115 000 2 100 2 600
324-RD 120 4.7244 260 10.2362 110 4.3307 2.5 .10 1.0 .040 22 100 34.3 436 000 98 000 600 000 135 000 2 000 2 400
326-RD 130 5.1181 280 11.0236 116 4.5669 3.0 .12 1.0 .040 25 700 39.8 475 000 107 000 695 000 156 000 1 800 2 200
328-RD 140 5.5118 300 11.8110 124 4.8819 3.0 .12 1.0 .040 29 500 45.7 572 000 129 000 800 000 180 000 1 700 2 100
330-RD 150 5.9055 320 12.5984 130 5.1181 3.0 .12 1.0 .040 33 900 52.6 624 000 140 000 950 000 214 000 1 600 1 900
332-RD 160 6.2992 340 13.3858 136 5.3543 3.0 .12 1.0 .040 38 400 59.6 689 000 155 000 1 080 000 243 000 1 400 1 800
334-RD 170 6.6929 360 14.1732 144 5.6693 3.0 .12 1.0 .040 40 800 63.2 715 000 161 000 1 140 000 256 000 1 400 1 700
336-RD 180 7.0866 380 14.9606 150 5.9055 3.0 .12 1.0 .040 45 700 70.9 780 000 175 000 1 270 000 286 000 1 300 1 600
338-RD 190 7.4803 400 15.7480 156 6.1417 4.0 .16 1.5 .060 51 000 79.0 832 000 187 000 1 430 000 321 000 1 300 1 500
340-RD 200 7.8740 420 16.5354 160 6.2992 4.0 .16 1.5 .060 56 400 87.5 904 000 203 000 1 560 000 351 000 1 200 1 400
342-RD 210 8.2677 440 17.3228 168 6.6142 4.0 .16 1.5 .060 62 200 96.5 956 000 215 000 1 730 000 389 000 1 100 1 400
344-RD 220 8.6614 460 18.1102 176 6.9291 4.0 .16 1.5 .060 68 400 106.0 1 040 000 234 000 1 900 000 427 000 1 000 1 300
348-RD 240 9.4488 500 19.6850 190 7.4803 4.0 .16 1.5 .060 74 800 116.0 1 080 000 243 000 2 120 000 477 000 880 1 100
352-RD 260 10.2362 540 21.2598 204 8.0315 5.0 .20 2.0 .080 87 100 135.0 1 210 000 272 000 2 500 000 562 000 880 1 000
356-RD 280 11.0236 580 22.8346 216 8.5039 5.0 .20 2.0 .080 102 000 158.0 1 350 000 303 000 2 900 000 652 000 780 960
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
Listed values are for pressed steel or polyamide cage, ABEC-1.
For phenolic composition cage, multiply by 1.66 for grease and 2.00 for oil. For machined bronze cage, multiply by 1.25 for grease and 1.50 for oil. For phenolic composition
cage, ABEC-5 or 7, multiply by 2.30 for grease and 2.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
112
400-R and 400-RD
Heavy Series
403-R 17 .6693 62 2.4409 17 .6693 1.0 .04 .60 .024 1 290 2.00 23 400 5 260 14 600 3 280 12 000 15 000
404-R 20 .7874 72 2.8346 19 .7480 1.0 .04 .60 .024 1 840 2.85 37 100 8 340 21 200 4 770 10 000 13 000
405-R 25 .9843 80 3.1496 21 .8268 1.5 .06 1.0 .040 2 270 3.52 44 900 10 100 26 500 5 960 9 000 11 000
406-R 30 1.1811 90 3.5433 23 .9055 1.5 .06 1.0 .040 3 050 4.73 49 400 11 100 36 000 8 090 8 500 10 000
407-R 35 1.3780 100 3.9370 25 .9843 1.5 .06 1.0 .040 3 620 5.62 58 500 13 200 44 000 9 890 7 000 8 500
408-R 40 1.5748 110 4.3307 27 1.0630 2.0 .08 1.0 .040 4 260 6.60 67 600 15 200 52 000 11 700 6 700 8 000
409-R 45 1.7717 120 4.7244 29 1.1417 2.0 .08 1.0 .040 4 940 7.66 78 000 17 500 61 000 13 700 6 000 7 000
410-R 50 1.9685 130 5.1181 31 1.2205 2.0 .08 1.0 .040 6 240 9.67 95 600 21 500 78 000 17 500 5 300 6 300
411-R 55 2.1654 140 5.5118 33 1.2992 2.0 .08 1.0 .040 7 100 11.0 108 000 24 300 90 000 20 200 5 000 6 000
412-R 60 2.3622 150 5.9055 35 1.3780 2.0 .08 1.0 .040 8 000 12.4 117 000 26 300 102 000 22 900 4 800 5 600
413-R 65 2.5591 160 6.2992 37 1.4567 2.0 .08 1.0 .040 8 970 13.9 127 000 28 600 112 000 25 200 4 500 5 300
414-R 70 2.7559 180 7.0866 42 1.6535 2.5 .10 1.0 .040 12 200 18.9 156 000 35 100 150 000 33 700 3 800 4 500
415-R 75 2.9528 190 7.4803 45 1.7717 2.5 .10 1.0 .040 13 400 20.8 168 000 37 800 166 000 37 300 3 600 4 300
416-R 80 3.1496 200 7.8740 48 1.8898 2.5 .10 1.0 .040 14 600 22.7 178 000 40 000 183 000 41 100 3 400 4 000
417-R 85 3.3465 210 8.2677 52 2.0472 3.0 .12 1.0 .040 16 000 24.8 190 000 42 700 200 000 45 000 3 200 3 800
418-R 90 3.5433 225 8.8583 54 2.1260 3.0 .12 1.0 .040 18 700 29.0 212 000 47 700 236 000 53 100 3 000 3 600
419-R 95 3.7402 250 9.8425 55 2.1654 3.0 .12 1.0 .040 21 700 33.7 234 000 52 600 275 000 60 700 2 700 3 300
420-R 100 3.9370 265 10.4331 60 2.3622 3.0 .12 1.0 .040 25 000 38.7 260 000 58 500 305 000 68 600 2 500 3 100
421-R 105 4.1339 290 11.4173 65 2.5591 3.0 .12 1.0 .040 29 200 45.2 286 000 64 300 355 000 79 800 2 400 2 900
422-R 110 4.3307 320 12.5984 70 2.7559 3.0 .12 1.0 .040 34 500 53.5 319 000 71 700 425 000 95 500 2 100 2 600
400-RD
403-RD 17 .6693 62 2.4409 34 1.3386 1.0 .04 .60 .024 1 290 2.00 37 700 8 480 29 000 6 520 9 600 12 000
404-RD 20 .7874 72 2.8346 38 1.4961 1.0 .04 .60 .024 1 840 2.85 60 500 13 600 42 500 9 550 8 000 10 000
405-RD 25 .9843 80 3.1496 42 1.6535 1.5 .06 1.0 .040 2 270 3.52 74 100 16 700 53 000 11 900 7 200 8 800
406-RD 30 1.1811 90 3.5433 46 1.8110 1.5 .06 1.0 .040 3 050 4.73 80 600 18 100 72 000 16 200 6 800 8 000
407-RD 35 1.3780 100 3.9370 50 1.9685 1.5 .06 1.0 .040 3 620 5.62 95 600 21 500 86 500 19 400 5 600 6 800
408-RD 40 1.5748 110 4.3307 54 2.1260 2.0 .08 1.0 .040 4 260 6.60 111 000 25 000 104 000 23 400 5 400 6 400
409-RD 45 1.7717 120 4.7244 58 2.2835 2.0 .08 1.0 .040 4 940 7.66 127 000 28 600 122 000 27 400 4 800 5 600
410-RD 50 1.9685 130 5.1181 62 2.4409 2.0 .08 1.0 .040 6 240 9.67 153 000 34 400 156 000 35 100 4 200 5 000
411-RD 55 2.1654 140 5.5118 66 2.5984 2.0 .08 1.0 .040 7 100 11.0 174 000 39 100 180 000 40 500 4 000 4 800
412-RD 60 2.3622 150 5.9055 70 2.7559 2.0 .08 1.0 .040 8 000 12.4 190 000 42 700 204 000 45 900 3 800 4 500
413-RD 65 2.5591 160 6.2992 74 2.9134 2.0 .08 1.0 .040 8 970 13.9 208 000 46 800 224 000 50 400 3 600 4 200
414-RD 70 2.7559 180 7.0866 84 3.3071 2.5 .10 1.0 .040 12 200 18.9 255 000 57 300 300 000 67 400 3 000 3 600
415-RD 75 2.9528 190 7.4803 90 3.5433 2.5 .10 1.0 .040 13 400 20.8 270 000 60 700 335 000 75 300 2 900 3 400
416-RD 80 3.1496 200 7.8740 96 3.7795 2.5 .10 1.0 .040 14 600 22.7 286 000 64 300 365 000 82 100 2 700 3 200
417-RD 85 3.3465 210 8.2677 104 4.0945 3.0 .12 1.0 .040 16 000 24.8 307 000 69 000 400 000 89 900 2 600 3 000
418-RD 90 3.5433 225 8.8583 108 4.2520 3.0 .12 1.0 .040 18 700 29.0 345 000 77 600 465 000 105 000 2 400 2 900
419-RD 95 3.7402 250 9.8425 110 4.3307 3.0 .12 1.0 .040 21 700 33.7 377 000 84 800 550 000 124 000 2 200 2 600
420-RD 100 3.9370 265 10.4331 120 4.7244 3.0 .12 1.0 .040 25 000 38.7 416 000 93 500 610 000 137 000 2 000 2 500
421-RD 105 4.1339 290 11.4173 130 5.1181 3.0 .12 1.0 .040 29 200 45.2 462 000 104 000 710 000 160 000 1 900 2 300
422-RD 110 4.3307 320 12.5984 140 5.5118 3.0 .12 1.0 .040 34 500 53.5 520 000 117 000 850 000 191 000 1 700 2 100
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
Listed values are for pressed steel or polyamide cage, ABEC-1.
For phenolic composition cage, multiply by 1.66 for grease and 2.00 for oil. For machined bronze cage, multiply by 1.25 for grease and 1.50 for oil. For phenolic composition
cage, ABEC-5 or 7, multiply by 2.30 for grease and 2.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
113
XLS Type Single-Row Inch Size
15° Angular Contact Ball Bearings MRC Bearing Services
XLS-1³|₈ 34.9 1.3750 65.1 2.5625 14.3 .5625 1.0 .04 .60 .024 1 060 1.65 22 500 5 060 15 600 3 510 11 000 13 000
XLS-1¹|₂ 38.1 1.5000 68.3 2.6875 14.3 .5625 1.0 .04 .60 .024 1 140 1.77 23 800 5 350 17 000 3 820 9 800 12 000
XLS-1⁵|₈ 41.3 1.6250 73.0 2.8750 14.3 .5625 1.0 .04 .60 .024 1 220 1.89 24 200 5 400 18 600 4 180 9 000 11 000
XLS-1³|₄ 44.5 1.7500 76.2 3.0000 14.3 .5625 1.0 .04 .60 .024 1 300 2.01 25 100 5 640 20 000 4 500 8 200 10 000
XLS-1⁷|₈ 47.6 1.8750 81.0 3.1875 15.9 .625 1.0 .04 .60 .024 1 540 2.39 29 600 6 650 23 600 5 310 8 200 10 000
XLS-2 50.8 2.0000 84.1 3.3125 15.9 .625 1.0 .04 .60 .024 1 630 2.53 30 200 6 790 25 500 5 730 7 800 9 500
XLS-2¹|₈ 54.0 2.1250 87.3 3.4375 15.9 .625 1.5 .06 .60 .024 1 630 2.53 30 200 6 790 25 500 5 730 7 400 9 000
XLS-2¹|₄ 57.2 2.2500 90.5 3.5625 15.9 .625 1.5 .06 .60 .024 1 720 2.67 31 200 7 010 27 000 6 070 7 100 8 700
XLS-2¹|₂-S 63.5 2.5000 98.4 3.8750 17.5 .6875 1.5 .06 .60 .024 1 360 2.11 26 000 5 850 22 000 4 950 6 500 7 900
XLS-2¹|₂ 63.5 2.5000 98.4 3.8750 17.5 .6875 1.5 .06 .60 .024 1 900 2.95 32 500 7 310 31 000 6 740 6 400 7 800
XLS-2⁵|₈ 66.7 2.6250 105 4.1250 17.5 .6875 1.5 .06 .60 .024 2 470 3.83 42 300 9 510 39 000 8 770 6 100 7 400
XLS-2³|₄ 69.9 2.7500 105 4.1250 17.5 .6875 1.5 .06 .60 .024 2 470 3.83 42 300 9 510 39 000 8 770 6 000 7 300
XLS-3 76.2 3.0000 114 4.5000 19.1 .750 2.0 .08 1.0 .040 2 720 4.21 44 200 9 940 44 000 9 890 5 500 6 700
XLS-3¹|₄ 82.6 3.2500 121 4.7500 19.1 .750 2.0 .08 1.0 .040 2 840 4.40 44 900 10 100 46 500 10 500 5 100 6 200
XLS-3¹|₂ 88.9 3.5000 127 5.0000 19.1 .750 2.0 .08 1.0 .040 3 090 4.79 47 500 10 700 51 000 11 500 4 800 5 900
XLS-3³|₄ 95.3 3.7500 133 5.2500 19.1 .750 2.0 .08 1.0 .040 3 210 4.98 47 500 10 700 53 000 11 900 4 500 5 500
XLS-4¹|₄ 108 4.2500 152 6.0000 22.2 .875 2.0 .08 1.0 .040 4 190 6.50 61 800 13 900 69 500 15 600 3 900 4 800
XLS-4¹|₂ 114 4.5000 159 6.2500 22.2 .875 2.0 .08 1.0 .040 4 350 6.75 61 800 13 900 73 500 16 500 3 800 4 600
XLS-4³|₄ 121 4.7500 165 6.5000 22.2 .875 2.0 .08 1.0 .040 4 520 7.00 63 700 14 300 76 500 17 200 3 600 4 400
XLS-5 127 5.0000 178 7.0000 25.4 1.000 2.0 .08 1.0 .040 5 510 8.54 78 000 17 500 91 500 20 600 3 400 4 100
XLS-5¹|₂ 140 5.5000 191 7.5000 25.4 1.000 2.5 .10 1.0 .040 5 920 9.18 79 300 17 800 100 000 22 500 3 100 3 800
XLS-6 152 6.0000 203 8.0000 25.4 1.000 2.5 .10 1.0 .040 6 330 9.81 81 900 18 400 108 000 24 300 2 900 3 500
XLS-6¹|₄ 159 6.2500 216 8.5000 28.6 1.125 2.5 .10 1.0 .040 7 550 11.7 97 500 21 900 129 000 29 000 2 700 3 300
XLS-6¹|₂ 165 6.5000 222 8.7500 28.6 1.125 2.5 .10 1.0 .040 7 800 12.0 99 500 22 400 134 000 30 100 2 600 3 200
XLS-7 178 7.0000 241 9.5000 31.8 1.250 3.0 .12 1.5 .060 9 480 14.7 119 000 26 800 160 000 36 000 2 400 2 900
XLS-7¹|₄ 184 7.2500 248 9.7500 31.8 1.250 3.0 .12 1.5 .060 9 740 15.1 121 000 27 200 166 000 37 300 2 300 2 800
XLS-7³|₄ 197 7.7500 267 10.5000 34.9 1.375 3.0 .12 1.5 .060 11 200 17.4 138 000 31 000 193 000 43 400 2 100 2 600
XLS-8 203 8.0000 273 10.7500 34.9 1.375 3.0 .12 1.5 .060 11 600 18.0 140 000 31 500 200 000 45 000 2 100 2 500
XLS-8¹|₄ 210 8.2500 279 11.0000 34.9 1.375 3.0 .12 1.5 .060 12 000 18.6 140 000 31 500 204 000 45 900 2 100 2 500
XLS-8¹|₂ 216 8.5000 292 11.5000 38.1 1.500 3.0 .12 1.5 .060 13 600 21.0 163 000 36 600 232 000 52 200 2 000 2 400
XLS-9 229 9.0000 305 12.0000 38.1 1.500 3.0 .12 1.5 .060 15 300 23.7 182 000 40 900 260 000 58 500 1 900 2 300
XLS-10 254 10.0000 337 13.2500 41.3 1.625 4.0 .16 1.5 .060 17 300 26.8 190 000 42 700 290 000 65 200 1 600 2 000
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2) Listed values are for pressed steel or polyamide cage, ABEC-1.
For phenolic composition cage, multiply by 1.66 for grease and 2.00 for oil. For machined bronze cage, multiply by 1.25 for grease and 1.50 for oil. For phenolic composition
cage, ABEC-5 or 7, multiply by 2.30 for grease and 2.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
114
115
Single-Row Angular Contact Ball Bearings
R-Type, Single Bearing MRC Bearing Services
Life rating
3
L10 = (CP) (Millions of revolutions)
or
6 3
L10h =
10 C
60n P
() (Hours)
116
Single-Row Angular Contact Ball Bearings
R-Type, Single Bearing
Case 1
Radial load (FR) = 1890
Equivalent load (P) = X FR + Y FA
P = FR = 1890 3 3
13200
Life (L10) = C =
P() 1890 ( )
= 341 × 106 Rev.
or 6 3 6 3
13200
Life (L10h) =
10 C
60n P
()
=
10
60 × 2000 1890
( )
= 2839 Hrs
Case 2
Radial load (FR) = 1890
Thrust load (FA) = 1250
Equivalent load (P) = XFR + YFA
FA/FR = 1250/1890 = 0.66
FA/ZD2 = 1250/4.69 = 267
X = 0.44
Y = 1.15
P = 0.44 × 1890 + 1.15 × 1250 = 2269
3 3
Life (L10) = (CP) = (13200
2269 )
= 197 × 106 Rev.
or 6 3 6 3
13200
Life (L10h) =
10 C
60n P
()
=
10
60 × 2000 2269
( )
= 1641 Hrs
Case 3
Thrust load (FA) = 1250
Equivalent load (P) = YFA
FA/ZD2 = 1250/4.69 = 267
Y = 1.15
P = 1.15 × 1250 = 1438
3 3
13200
Life (L10) =
C
P() =
1438 ( ) = 773 × 106 Rev.
or 6 3 6 3
13200
Life (L10h) =
10 C
60n P
()
=
10
60 × 2000 1438
( )
= 6446 Hrs
117
Single-Row Angular Contact Ball Bearings
RD-Type, Duplex MRC Bearing Services
For DB or DF mounting:
C = Duplex pair dynamic radial load
rating (from duplex bearing tables)
or
118
Single-Row Angular Contact Ball Bearings,
RD-Type, Duplex
or 6 3 6 3
Life (L10) = (CP) = (28481
2550 )
= 1393 × 106 Rev.
21500
10 C
() 10
Life (L10h) = 60n P = 60 × 2000 3686 ( ) or 6 3 6
28481
3
10 C
() 10
Life (L10h) = 60n P = 60 × 2000 2550 ( )
= 1654 Hrs
= 11611 Hrs
Case 2 Case 2
Radial load (FR) = 1890 Radial load (FR) = 1890
Thrust load (FA) = 450 Thrust load (FA) = 2500
Equivalent load (P) = X FR + Y FA Equivalent load (P) = X FR + Y FA
FA/FR = 450/1890 = 0.24 FA/FR = 2500/1890 = 1.32
FA/ZD2 = 450/4.69 = 96 FA/ZD2 = 2500/4.69 = 533
Since FA/FR < e, X = 1.0, Y = 1.46 Since FA/FR > e, X = 0.44, Y = 1.02
P = 1.0 × 1890 + 1.46 × 450 = 2547 P = 0.44 × 1890 + 1.02 × 2500 = 3382
3 3 Load rating = (i)0.7 × 13200
Life (L10) = (CP) = (21500
2547 )
= 601 × 106 Rev. = (3)0.7 × 13200 = 28481
3 3
or 6
10 C
()
3
10
6
21500
Life (L10h) = 60n P = 60 × 2000 2547 ( )
3 Life (L10) = (CP) = (28481
3382 )
= 597 × 106 Rev.
or 6 3 6 3
28481
= 5012 Hrs
10 C
() 10
Life (L10h) = 60n P = 60 × 2000 3382 ( )
= 4977 Hrs
Case 3
Thrust load (FA) = 1250
Equivalent load (P) = X FR + Y FA
FA/FR = 1250/0 = ∞
FA/ZD2 = 1250/4.69 = 267
Since FA/FR > e, Y = 1.86
P = 1.86 × 1250 = 2325
3 3
Life (L10) = (CP) = (21500
2325 )
= 791 × 106 Rev.
or 6 3 6 3
21500
10 C
() 10
Life (L10h) = 60n P = 60 × 2000 2325 ( )
= 6590 Hrs
119
120
7000 Series Single-Row 29°
Angular Contact Ball Bearings
MRC 7000 Series bearings are single-row 29° Cage Types and Materials
angular contact ball bearings having one heavy race
shoulder and one counterbored race shoulder on For normal usage: heavy stock, two-piece steel
the outer ring. Because of this construction, it is formed pockets, with turned-over fingers or riveted
possible to incorporate a greater number of balls together.
than in the deep groove nonfilling notch bearing.
The combination of maximum ball complement and For severe vibration, very high speeds, or high
the angular contact feature reduces the specific ball operating temperatures: one-piece, inner ring land-
loading under thrust load, resulting in moderate to guided, machined construction of suitable material
high thrust load carrying capacity. (phenolic/bakelite composition, machined brass, or
MRC 7000 Series angular contact ball bearings should special material).
be used in applications in which the thrust load is
heavy and beyond the capacity of single-row types;
for example, for a heavy thrust load in one direction,
or a heavy thrust load in one direction combined with
a radial load.
121
7100 and 7100-D
Extra Large Series MRC Bearing Services
71205) 100 3.9370 160 6.2992 28 1.1024 2.0 .08 1.0 .040 85 200 19 200 86 500 19 400 2 600 4 300
7122 110 4.3307 175 6.8898 30 1.1811 2.0 .08 1.0 .040 104 000 23 400 108 000 24 300 2 400 4 000
71245) 120 4.7244 190 7.4803 32 1.2598 2.0 .08 1.0 .040 108 000 24 300 127 000 28 600 2 200 3 700
71265) 130 5.1181 205 8.0709 34 1.3386 2.0 .08 1.0 .040 121 000 27 200 134 000 30 100 2 100 3 500
71285) 140 5.5118 220 8.6614 36 1.4173 2.0 .08 1.0 .040 138 000 31 000 156 000 35 100 1 900 3 200
7130 150 5.9055 235 9.2520 38 1.4961 2.0 .08 1.0 .040 159 000 35 700 180 000 40 500 1 700 2 800
71325) 160 6.2992 250 9.8425 40 1.5748 2.0 .08 1.0 .040 174 000 39 100 204 000 45 900 1 600 2 700
71345) 170 6.6929 265 10.4331 42 1.6535 2.5 .10 1.0 .040 190 000 42 700 232 000 52 200 1 600 2 700
71365) 180 7.0866 280 11.0236 44 1.7323 2.5 .10 1.0 .040 208 000 46 800 260 000 58 500 1 600 2 600
71385) 190 7.4803 300 11.8110 46 1.8110 2.5 .10 1.0 .040 242 000 54 400 315 000 70 800 1 400 2 400
71405) 200 7.8740 320 12.5984 48 1.8898 2.5 .10 1.0 .040 260 000 58 500 355 000 79 800 1 400 2 300
71425) 210 8.2677 340 13.3858 50 1.9685 2.5 .10 1.0 .040 286 000 64 300 400 000 89 900 1 400 2 300
71445) 220 8.6614 350 13.7795 51 2.0079 2.5 .10 1.0 .040 291 000 65 400 415 000 93 300 1 300 2 200
71465) 230 9.0551 370 14.5669 53 2.0866 3.0 .12 1.0 .040 312 000 70 100 455 000 102 000 1 200 2 000
71485) 240 9.4488 390 15.3543 55 2.1654 3.0 .12 1.0 .040 332 000 74 600 500 000 112 000 1 100 1 900
71525) 260 10.2362 430 16.9291 59 2.3228 3.0 .12 1.0 .040 364 000 81 800 585 000 132 000 1 100 1 800
71565) 280 11.0236 460 18.1102 63 2.4803 3.0 .12 1.0 .040 403 000 90 600 600 000 135 000 1 100 1 800
71645) 320 12.5984 500 19.6850 71 2.7953 3.0 .12 1.0 .040 462 000 104 000 815 000 183 000 960 1 600
7100-D
7120-D5) 100 3.9370 160 6.2992 56 2.2047 2.0 .08 1.0 .040 140 000 31 500 173 000 38 900 2 100 3 400
7122-D 110 4.3307 175 6.8898 60 2.3622 2.0 .08 1.0 .040 168 000 37 800 216 000 48 600 1 900 3 200
7124-D5) 120 4.7244 190 7.4803 64 2.5197 2.0 .08 1.0 .040 178 000 40 000 255 000 57 300 1 800 3 000
7126-D5) 130 5.1181 205 8.0709 68 2.6772 2.0 .08 1.0 .040 195 000 43 800 270 000 60 700 1 700 2 800
7128-D5) 140 5.5118 220 8.6614 72 2.8346 2.0 .08 1.0 .040 225 000 50 600 310 000 69 700 1 500 2 600
7130-D 150 5.9055 235 9.2520 76 2.9921 2.0 .08 1.0 .040 255 000 57 300 360 000 80 900 1 400 2 200
7132-D5) 160 6.2992 250 9.8425 80 3.1496 2.0 .08 1.0 .040 286 000 64 300 405 000 91 000 1 300 2 200
7134-D5) 170 6.6929 265 10.4331 84 3.3071 2.5 .10 1.0 .040 312 000 70 100 465 000 105 000 1 300 2 200
7136-D5) 180 7.0866 280 11.0236 88 3.4646 2.5 .10 1.0 .040 338 000 76 000 520 000 117 000 1 300 2 100
7138-D5) 190 7.4803 300 11.8110 92 3.6220 2.5 .10 1.0 .040 390 000 87 700 630 000 142 000 1 100 1 900
7140-D5) 200 7.8740 320 12.5984 96 3.7795 2.5 .10 1.0 .040 423 000 95 100 695 000 156 000 1 100 1 800
7142-D5) 210 8.2677 340 13.3858 100 3.9370 2.5 .10 1.0 .040 468 000 105 000 800 000 180 000 1 100 1 800
7144-D5) 220 8.6614 350 13.7795 102 4.0157 2.5 .10 1.0 .040 475 000 107 000 830 000 187 000 1 000 1 800
7146-D5) 230 9.0551 370 14.5669 106 4.1732 3.0 .12 1.0 .040 507 000 114 000 915 000 206 000 960 1 600
7148-D5) 240 9.4488 390 15.3543 110 4.3307 3.0 .12 1.0 .040 540 000 121 000 1 000 000 225 000 880 1 500
7152-D5) 260 10.2362 430 16.9291 118 4.6457 3.0 .12 1.0 .040 592 000 133 000 1 160 000 261 000 880 1 400
7156-D5) 280 11.0236 460 18.1102 126 4.9606 3.0 .12 1.0 .040 663 000 149 000 1 200 000 270 000 880 1 400
7164-D5) 320 12.5984 500 19.6850 142 5.5906 3.0 .12 1.0 .040 761 000 171 000 1 630 000 366 000 770 1 300
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
For thrust rating multiply C by 1.32 and C0 by 2.94 (single) and C by 0.81 and C0 by 1.47 (duplex).
3) Listed values are for machined bronze cage, ABEC-1.
For phenolic composition cage, multiply by 1.33 for both grease and oil. For phenolic composition cage, ABEC-5 or 7, multiply by 1.86 for both grease and oil. For pressed
steel cage, ABEC-1, multiply by 0.67 for grease and 0.80 for oil. The speed rating adjustment factors have been determined through historical application and practice.
For a more complete explanation, see page 274.
4) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
5) Typically non-stocked sizes, please check availability before designing into equipment.
122
7100-KR Extra Light Series
(Single Bearings)
7100-KR 10 .3937 26 1.0236 8 .3150 .30 .012 .10 .004 4 620 1 040 2 000 450 30 000 39 000
7101-KR 12 .4724 28 1.1024 8 .3150 .30 .012 .10 .004 4 940 1 110 2 500 562 25 000 32 000
7102-KR 15 .5906 32 1.2598 9 .3543 .30 .012 .10 .004 5 400 1 210 2 900 652 22 000 28 000
7103-KR 17 .6693 35 1.3780 10 .3937 .30 .012 .10 .004 7 610 1 710 4 250 955 19 000 25 000
7104-KR 20 .7874 42 1.6535 12 .4724 .64 .025 .30 .012 9 560 2 150 5 700 1 280 16 000 21 000
7105-KR 25 .9843 47 1.8504 12 .4724 .64 .025 .30 .012 10 600 2 380 6 950 1 560 12 000 16 000
7106-KR 30 1.1811 55 2.1654 13 .5118 1.0 .04 .30 .012 13 800 3 100 9 650 2 170 11 000 14 000
7107-KR 35 1.3780 62 2.4409 14 .5512 1.0 .04 .30 .012 16 800 3 780 12 000 2 700 9 200 12 000
7108-KR 40 1.5748 68 2.6772 15 .5906 1.0 .04 .30 .012 17 200 3 870 13 200 2 970 8 500 11 000
7109-KR 45 1.7717 75 2.9528 16 .6299 1.0 .04 .30 .012 21 200 4 770 17 000 3 820 7 500 9 800
7110-KR 50 1.9685 80 3.1496 16 .6299 1.0 .04 .30 .012 22 100 4 970 18 300 4 110 6 900 9 000
7111-KR 55 2.1654 90 3.5433 18 .7087 1.0 .04 .60 .024 29 600 6 650 25 500 5 730 6 300 8 200
7112-KR 60 2.3622 95 3.7402 18 .7087 1.0 .04 .60 .024 30 700 6 900 27 000 6 070 5 700 7 400
7113-KR 65 2.5591 100 3.9370 18 .7087 1.0 .04 .60 .024 31 200 7 010 29 000 6 520 5 400 7 000
7114-KR 70 2.7559 110 4.3307 20 .7874 1.0 .04 .60 .024 34 500 7 760 35 500 7 980 5 000 6 500
7115-KR 75 2.9528 115 4.5276 20 .7874 1.0 .04 .60 .024 37 700 8 480 37 500 8 430 4 700 6 100
7116-KR 80 3.1496 125 4.9213 22 .8661 1.0 .04 .60 .024 48 800 11 000 49 000 11 000 4 500 5 800
7117-KR 85 3.3465 130 5.1181 22 .8661 1.0 .04 .60 .024 49 400 11 100 52 000 11 700 4 100 5 300
7118-KR 90 3.5433 140 5.5118 24 .9449 1.5 .06 .60 .024 58 500 13 200 61 000 13 700 3 800 4 900
7119-KR 95 3.7402 145 5.7087 24 .9449 1.5 .06 .60 .024 71 500 16 100 72 000 16 200 3 600 4 700
7120-KR 100 3.9370 150 5.9055 24 .9449 1.5 .06 1.0 .040 62 400 14 000 68 000 15 300 3 500 4 500
7121-KR 105 4.1339 160 6.2992 26 1.0236 2.0 .08 1.0 .040 74 100 16 700 80 000 18 000 3 300 4 300
7122-KR 110 4.3307 170 6.6929 28 1.1024 2.0 .08 1.0 .040 87 100 19 600 91 500 20 600 3 200 3 800
7124-KR 120 4.7244 180 7.0866 28 1.1024 2.0 .08 1.0 .040 88 400 19 900 98 000 22 000 2 900 3 800
7126-KR 130 5.1181 200 7.8740 33 1.2992 2.0 .08 1.0 .040 121 000 27 200 134 000 30 100 2 700 3 500
7128-KR 140 5.5118 210 8.2677 33 1.2992 2.0 .08 1.0 .040 121 000 27 200 137 000 30 800 2 500 3 300
7130-KR 150 5.9055 225 8.8583 35 1.3780 2.0 .08 1.0 .040 135 000 30 300 156 000 35 100 2 200 2 900
7132-KR 160 6.2992 240 9.4488 38 1.4961 2.0 .08 1.0 .040 156 000 35 100 180 000 40 500 2 200 2 800
7134-KR 170 6.6929 260 10.2362 42 1.6535 2.0 .08 1.0 .040 186 000 41 800 220 000 49 500 2 100 2 700
7136-KR 180 7.0866 280 11.0236 46 1.8110 2.0 .08 1.0 .040 208 000 46 800 260 000 58 500 2 000 2 600
7138-KR 190 7.4803 290 11.4173 46 1.8110 2.0 .08 1.0 .040 212 000 47 700 270 000 60 700 1 800 2 400
7140-KR 200 7.8740 310 12.2047 51 2.0079 2.0 .08 1.0 .040 238 000 53 500 320 000 71 900 1 800 2 300
7144-KR 220 8.6614 340 13.3858 56 2.2047 2.5 .10 1.0 .040 302 000 67 900 430 000 96 700 1 700 2 200
7148-KR 240 9.4488 360 14.1732 56 2.2047 2.5 .10 1.0 .040 307 000 69 000 455 000 102 000 1 500 2 000
7152-KR 260 10.2362 400 15.7480 65 2.5591 3.0 .12 1.5 .060 377 000 84 800 585 000 132 000 1 500 1 900
7156-KR 280 11.0236 420 16.5354 65 2.5591 3.0 .12 1.5 .060 390 000 87 700 620 000 139 000 1 500 1 900
7160-KR 300 11.8110 460 18.1102 74 2.9134 3.0 .12 1.5 .060 449 000 101 000 765 000 172 000 1 300 1 700
7164-KR 320 12.5984 480 18.8976 74 2.9134 3.0 .12 1.5 .060 462 000 104 000 815 000 183 000 1 200 1 600
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
For thrust rating multiply C by 1.32 and C0 by 2.94.
3) Listed values are for machined bronze cage, ABEC-1.
For phenolic composition cage, multiply by 1.33 for both grease and oil. For phenolic composition cage, ABEC-5 or 7, multiply by 1.86 for both grease and oil. For pressed
steel cage, ABEC-1, multiply by 0.67 for grease and 0.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 274.
4) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
123
7100-KRD Extra Light Series
Duplex MRC Bearing Services
“D” indicates a duplex ground half pair matched with an identical half pair and is fol-
lowed by an additional suffix letter to describe the type of duplex. See pages 234 and
235 for suffix description.
Note: ABEC - 1 & 3 stocked as half-pairs, where available. Use these values for back-to-back (DB) or face-to-face (DF) mounting arrangements.
7100-KRD 10 .3937 26 1.0236 16 .6299 .30 .012 .10 .004 7 610 1 710 4 150 933 24 000 31 000
7101-KRD 12 .4724 28 1.1024 16 .6299 .30 .012 .10 .004 8 060 1 810 5 000 1 120 20 000 26 000
7102-KRD 15 .5906 32 1.2598 18 .7087 .30 .012 .10 .004 8 840 1 990 5 850 1 320 18 000 22 000
7103-KRD 17 .6693 35 1.3780 20 .7874 .30 .012 .10 .004 12 500 2 810 8 500 1 910 15 000 20 000
7104-KRD 20 .7874 42 1.6535 24 .9449 .64 .025 .30 .012 15 600 3 510 11 400 2 560 13 000 17 000
7105-KRD 25 .9843 47 1.8504 24 .9449 .64 .025 .30 .012 17 400 3 910 14 000 3 150 9 600 13 000
7106-KRD 30 1.1811 55 2.1654 26 1.0236 1.0 .04 .30 .012 22 500 5 060 19 300 4 340 8 800 11 000
7107-KRD 35 1.3780 62 2.4409 28 1.1024 1.0 .04 .30 .012 27 600 6 200 24 000 5 400 7 400 9 600
7108-KRD 40 1.5748 68 2.6772 30 1.1811 1.0 .04 .30 .012 28 100 6 320 26 000 5 850 6 800 8 800
7109-KRD 45 1.7717 75 2.9528 32 1.2598 1.0 .04 .30 .012 34 500 7 760 34 000 7 640 6 000 7 800
7110-KRD 50 1.9685 80 3.1496 32 1.2598 1.0 .04 .30 .012 35 800 8 050 36 500 8 210 5 500 7 200
7111-KRD 55 2.1654 90 3.5433 36 1.4173 1.0 .04 .60 .024 47 500 10 700 51 000 11 500 5 000 6 600
7112-KRD 60 2.3622 95 3.7402 36 1.4173 1.0 .04 .60 .024 49 400 11 100 54 000 12 100 4 600 5 900
7113-KRD 65 2.5591 100 3.9370 36 1.4173 1.0 .04 .60 .024 50 700 11 400 58 500 13 200 4 300 5 600
7114-KRD 70 2.7559 110 4.3307 40 1.5748 1.0 .04 .60 .024 55 900 12 600 71 000 16 000 4 000 5 200
7115-KRD 75 2.9528 115 4.5276 40 1.5748 1.0 .04 .60 .024 61 800 13 900 75 000 16 900 3 800 4 900
7116-KRD 80 3.1496 125 4.9213 44 1.7323 1.0 .04 .60 .024 79 300 17 800 98 000 22 000 3 600 4 600
7117-KRD 85 3.3465 130 5.1181 44 1.7323 1.0 .04 .60 .024 80 600 18 100 104 000 23 400 3 300 4 200
7118-KRD 90 3.5433 140 5.5118 48 1.8898 1.5 .06 .60 .024 95 600 21 500 122 000 27 400 3 000 3 900
7119-KRD 95 3.7402 145 5.7087 48 1.8898 1.5 .06 .60 .024 117 000 26 300 143 000 32 100 2 900 3 800
7120-KRD 100 3.9370 150 5.9055 48 1.8898 1.5 .06 1.0 .040 101 000 22 700 137 000 30 800 2 800 3 600
7121-KRD 105 4.1339 160 6.2992 52 2.0472 2.0 .08 1.0 .040 121 000 27 200 160 000 36 000 2 600 3 400
7122-KRD 110 4.3307 170 6.6929 56 2.2047 2.0 .08 1.0 .040 140 000 31 500 183 000 41 100 2 600 3 300
7124-KRD 120 4.7244 180 7.0866 56 2.2047 2.0 .08 1.0 .040 143 000 32 100 196 000 44 100 2 300 3 000
7126-KRD 130 5.1181 200 7.8740 66 2.5984 2.0 .08 1.0 .040 195 000 43 800 270 000 60 700 2 200 2 800
7128-KRD 140 5.5118 210 8.2677 66 2.5984 2.0 .08 1.0 .040 195 000 43 800 270 000 60 700 2 000 2 600
7130-KRD 150 5.9055 225 8.8583 70 2.7559 2.0 .08 1.0 .040 221 000 49 700 315 000 70 800 1 800 2 300
7132-KRD 160 6.2992 240 9.4488 76 2.9921 2.0 .08 1.0 .040 255 000 57 300 360 000 80 900 1 800 2 200
7134-KRD 170 6.6929 260 10.2362 84 3.3071 2.0 .08 1.0 .040 302 000 67 900 440 000 98 900 1 700 2 200
7136-KRD 180 7.0866 280 11.0236 92 3.6220 2.0 .08 1.0 .040 338 000 76 000 520 000 117 000 1 600 2 100
7138-KRD 190 7.4803 290 11.4173 92 3.6220 2.0 .08 1.0 .040 345 000 77 600 540 000 121 000 1 400 1 900
7140-KRD 200 7.8740 310 12.2047 102 4.0157 2.0 .08 1.0 .040 390 000 87 700 640 000 144 000 1 400 1 800
7144-KRD 220 8.6614 340 13.3858 112 4.4094 2.5 .10 1.0 .040 494 000 111 000 865 000 194 000 1 400 1 800
7148-KRD 240 9.4488 360 14.1732 112 4.4094 2.5 .10 1.0 .040 494 000 111 000 915 000 206 000 1 200 1 600
7152-KRD 260 10.2362 400 15.7480 130 5.1181 3.0 .12 1.5 .060 618 000 139 000 1 180 000 265 000 1 200 1 500
7156-KRD 280 11.0236 420 16.5354 130 5.1181 3.0 .12 1.5 .060 637 000 143 000 1 250 000 281 000 1 200 1 500
7160-KRD 300 11.8110 460 18.1102 148 5.8268 3.0 .12 1.5 .060 728 000 164 000 1 580 000 355 000 1 000 1 400
7164-KRD 320 12.5984 480 18.8976 148 5.8268 3.0 .12 1.5 .060 761 000 171 000 1 630 000 366 000 960 1 300
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
For thrust rating multiply C by 0.81 and Co by 1.47.
3)
Listed values are for machined bronze cage, ABEC-1.
For phenolic composition cage, multiply by 1.33 for both grease and oil. For phenolic composition cage, ABEC-5 or 7, multiply by 1.86 for both grease and oil. For pressed
steel cage, ABEC-1, multiply by 0.67 for grease and 0.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 274.
4) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
124
7200 Light Series
(Single Bearings)
The 7200 Series contains single-row angular contact ball
bearings with a counterbored outer ring. Bore sizes
range from 10 mm to 320 mm; and most of these
bearings are available with a two-piece pressed steel
cage, or a one-piece nonmetallic or solid bronze cage.
7000 Series bearings are designed with an initial
contact angle of 29°, although some small sizes may
have a lesser angle. 7200 Series bearings can be used
with moderate to heavy one-directional thrust loads, or
combined radial and thrust loads where the thrust load
is predominant.
Caution: Single bearings are not to be used where
only radial loads are present. For two-direction
thrust loads, use duplex bearings.
Basic Radial Load Rating2) Speed Rating3)
MRC Bore Outside Width Fillet Radius 1)
7200 10 .3937 30 1.1811 9 .3543 .64 .025 .30 .012 5 400 1 210 2 750 618 28 000 36 000
7201 12 .4724 32 1.2598 10 .3937 .64 .025 .30 .012 6 240 1 400 3 200 719 22 000 29 000
7202 15 .5906 35 1.3780 11 .4331 .64 .025 .30 .012 9 040 2 030 4 750 1 070 20 000 26 000
7203 17 .6693 40 1.5748 12 .4724 .64 .025 .30 .012 11 900 2 680 6 550 1 470 18 000 23 000
7204 20 .7874 47 1.8504 14 .5512 1.0 .04 .60 .024 12 700 2 860 7 200 1 620 15 000 19 000
7205 25 .9843 52 2.0472 15 .5906 1.0 .04 .60 .024 15 300 3 440 9 500 2 140 12 000 16 000
7206 30 1.1811 62 2.4409 16 .6299 1.0 .04 .60 .024 16 800 3 780 11 800 2 650 10 000 13 000
7207 35 1.3780 72 2.8346 17 .6693 1.0 .04 .60 .024 23 400 5 260 17 000 3 820 9 200 12 000
7208 40 1.5748 80 3.1496 18 .7087 1.0 .04 .60 .024 30 700 6 900 22 800 5 130 7 700 10 000
7209 45 1.7717 85 3.3465 19 .7480 1.0 .04 .60 .024 30 700 6 900 23 200 5 220 7 300 9 500
7210 50 1.9685 90 3.5433 20 .7874 1.0 .04 .60 .024 33 200 7 460 27 000 6 070 6 400 8 300
7211 55 2.1654 100 3.9370 21 .8268 1.5 .06 1.0 .040 48 800 11 000 37 500 8 430 6 000 7 800
7212 60 2.3622 110 4.3307 22 .8661 1.5 .06 1.0 .040 52 700 11 800 44 000 9 890 5 400 7 000
7213 65 2.5591 120 4.7244 23 .9055 1.5 .06 1.0 .040 63 700 14 300 54 000 12 100 4 900 6 400
7214 70 2.7559 125 4.9213 24 .9449 1.5 .06 1.0 .040 63 700 14 300 55 000 12 400 4 600 6 000
7215 75 2.9528 130 5.1181 25 .9843 1.5 .06 1.0 .040 79 300 17 800 69 500 15 600 4 300 5 600
7216 80 3.1496 140 5.5118 26 1.0236 2.0 .08 1.0 .040 74 100 16 700 67 000 15 100 4 100 5 300
7217 85 3.3465 150 5.9055 28 1.1024 2.0 .08 1.0 .040 90 400 20 300 83 000 18 700 3 800 4 900
7218 90 3.5433 160 6.2992 30 1.1811 2.0 .08 1.0 .040 117 000 26 300 118 000 26 500 3 600 4 700
7219 95 3.7402 170 6.6929 32 1.2598 2.0 .08 1.0 .040 121 000 27 200 114 000 25 600 3 500 4 500
7220 100 3.9370 180 7.0866 34 1.3386 2.0 .08 1.0 .040 138 000 31 000 129 000 29 000 3 200 4 100
7221 105 4.1339 190 7.4803 36 1.4173 2.0 .08 1.0 .040 148 000 33 300 137 000 30 800 3 000 3 900
7222 110 4.3307 200 7.8740 38 1.4961 2.0 .08 1.0 .040 163 000 36 600 156 000 35 100 2 900 3 800
7224 120 4.7244 215 8.4646 40 1.5748 2.0 .08 1.0 .040 174 000 39 100 176 000 39 600 2 700 3 500
7226 130 5.1181 230 9.0551 40 1.5748 2.5 .10 1.0 .040 195 000 43 800 208 000 46 800 2 500 3 200
7228 140 5.5118 250 9.8425 42 1.6535 2.5 .10 1.0 .040 208 000 46 800 232 000 52 200 2 300 3 000
7230 150 5.9055 270 10.6299 45 1.7717 2.5 .10 1.0 .040 242 000 54 400 280 000 62 900 2 100 2 700
7232 160 6.2992 290 11.4173 48 1.8898 2.5 .10 1.0 .040 270 000 60 700 325 000 73 100 2 000 2 600
7234 170 6.6929 310 12.2047 52 2.0472 3.0 .12 1.0 .040 286 000 64 300 365 000 82 100 1 900 2 500
7236 180 7.0866 320 12.5984 52 2.0472 3.0 .12 1.0 .040 302 000 67 900 390 000 87 700 1 900 2 400
7238 190 7.4803 340 13.3858 55 2.1654 3.0 .12 1.0 .040 332 000 74 600 450 000 101 000 1 700 2 200
7240 200 7.8740 360 14.1732 58 2.2835 3.0 .12 1.0 .040 351 000 78 900 490 000 110 000 1 600 2 100
7242 210 8.2677 380 14.9606 61 2.4016 3.0 .12 1.0 .040 390 000 87 700 560 000 126 000 1 500 2 000
7244 220 8.6614 400 15.7480 65 2.5591 3.0 .12 1.0 .040 403 000 90 600 600 000 135 000 1 500 2 000
7246 230 9.0551 420 16.5354 68 2.6772 3.0 .12 1.0 .040 442 000 99 400 670 000 151 000 1 500 1 900
7248 240 9.4488 440 17.3228 72 2.8346 3.0 .12 1.0 .040 475 000 107 000 750 000 169 000 1 400 1 800
7250 250 9.8425 460 18.1102 76 2.9921 4.0 .16 1.5 .060 520 000 117 000 830 000 187 000 1 400 1 800
7252 260 10.2362 480 18.8976 80 3.1496 4.0 .16 1.5 .060 559 000 126 000 915 000 206 000 1 300 1 700
7256 280 11.0236 500 19.6850 80 3.1496 4.0 .16 1.5 .060 572 000 129 000 980 000 220 000 1 300 1 700
7260 300 11.8110 540 21.2598 85 3.3465 4.0 .16 1.5 .060 618 000 139 000 1 100 000 247 000 1 200 1 600
7264 320 12.5984 580 22.8346 92 3.6220 4.0 .16 1.5 .060 650 000 146 000 1 220 000 274 000 1 200 1 500
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
For thrust rating multiply C by 1.32 and C0 by 2.94.
3) Listed values are for machined bronze cage, ABEC-1.
For phenolic composition cage, multiply by 1.33 for both grease and oil. For phenolic composition cage, ABEC-5 or 7, multiply by 1.86 for both grease and oil. For pressed
steel cage, ABEC-1, multiply by 0.67 for grease and 0.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 274.
4) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
125
7200-D Light Series
Duplex MRC Bearing Services
Note: ABEC-1 & 3 stocked as half-pairs, where available. Use these values for back-to-back (DB) or face-to-face (DF) mounting arrangements.
7200-D 10 .3937 30 1.1811 18 .7087 .64 .025 .30 .012 8 840 1 900 5 500 1 240 22 000 29 000
7201-D 12 .4724 32 1.2598 20 .7874 .64 .025 .30 .012 10 100 2 270 6 400 1 440 18 000 23 000
7202-D 15 .5906 35 1.3780 22 .8661 .64 .025 .30 .012 14 800 3 330 9 500 2 140 16 000 21 000
7203-D 17 .6693 40 1.5748 24 .9449 .64 .025 .30 .012 19 500 4 380 13 200 2 970 14 000 18 000
7204-D 20 .7874 47 1.8504 28 1.1024 1.0 .04 .60 .024 20 800 4 680 14 600 3 280 12 000 15 000
7205-D 25 .9843 52 2.0472 30 1.1811 1.0 .04 .60 .024 25 100 5 640 19 000 4 270 9 600 13 000
7206-D 30 1.1811 62 2.4409 32 1.2598 1.0 .04 .60 .024 27 600 6 200 23 600 5 310 8 000 10 000
7207-D 35 1.3780 72 2.8346 34 1.3386 1.0 .04 .60 .024 37 700 8 480 34 000 7 640 7 400 9 600
7208-D 40 1.5748 80 3.1496 36 1.4173 1.0 .04 .60 .024 49 400 11 100 45 500 10 200 6 200 8 000
7209-D 45 1.7717 85 3.3465 38 1.4961 1.0 .04 .60 .024 49 400 11 100 46 500 10 500 5 800 7 600
7210-D 50 1.9685 90 3.5433 40 1.5748 1.0 .04 .60 .024 54 000 12 100 54 000 12 100 5 100 6 600
7211-D 55 2.1654 100 3.9370 42 1.6535 1.5 .06 1.0 .040 79 300 17 800 75 000 16 900 4 800 6 200
7212-D 60 2.3622 110 4.3307 44 1.7323 1.5 .06 1.0 .040 85 200 19 100 88 000 19 800 4 300 5 600
7213-D 65 2.5591 120 4.7244 46 1.8110 1.5 .06 1.0 .040 104 000 23 400 110 000 24 700 3 900 5 100
7214-D 70 2.7559 125 4.9213 48 1.8898 1.5 .06 1.0 .040 104 000 23 400 110 000 24 700 3 700 4 800
7215-D 75 2.9528 130 5.1181 50 1.9685 1.5 .06 1.0 .040 130 000 29 200 140 000 31 500 3 400 4 500
7216-D 80 3.1496 140 5.5118 52 2.0472 2.0 .08 1.0 .040 121 000 27 200 134 000 30 100 3 300 4 200
7217-D 85 3.3465 150 5.9055 56 2.2047 2.0 .08 1.0 .040 148 000 33 300 166 000 37 300 3 000 3 900
7218-D 90 3.5433 160 6.2992 60 2.3622 2.0 .08 1.0 .040 190 000 42 700 236 000 53 100 2 900 3 800
7219-D 95 3.7402 170 6.6929 64 2.5197 2.0 .08 1.0 .040 199 000 44 700 228 000 51 300 2 800 3 600
7220-D 100 3.9370 180 7.0866 68 2.6772 2.0 .08 1.0 .040 225 000 50 600 260 000 58 500 2 600 3 300
7221-D 105 4.1339 190 7.4803 72 2.8346 2.0 .08 1.0 .040 242 000 54 400 295 000 66 300 2 400 3 100
7222-D 110 4.3307 200 7.8740 76 2.9921 2.0 .08 1.0 .040 265 000 59 600 310 000 69 700 2 300 3 000
7224-D 120 4.7244 215 8.4646 80 3.1496 2.0 .08 1.0 .040 281 000 63 200 355 000 79 800 2 200 2 800
7226-D 130 5.1181 230 9.0551 80 3.1496 2.5 .10 1.0 .040 319 000 71 700 415 000 93 300 2 000 2 600
7228-D 140 5.5118 250 9.8425 84 3.3071 2.5 .10 1.0 .040 338 000 76 000 465 000 105 000 1 800 2 400
7230-D 150 5.9055 270 10.6299 90 3.5433 2.5 .10 1.0 .040 397 000 89 200 560 000 126 000 1 700 2 200
7232-D 160 6.2992 290 11.4173 96 3.7795 2.5 .10 1.0 .040 442 000 99 400 670 000 135 000 1 600 2 100
7234-D 170 6.6929 310 12.2047 104 4.0945 3.0 .12 1.0 .040 468 000 105 000 735 000 165 000 1 500 2 000
7236-D 180 7.0866 320 12.5984 104 4.0945 3.0 .12 1.0 .040 494 000 111 000 780 000 175 000 1 500 1 900
7238-D 190 7.4803 340 13.3858 110 4.3307 3.0 .12 1.0 .040 540 000 121 000 900 000 202 000 1 400 1 800
7240-D 200 7.8740 360 14.1732 116 4.5669 3.0 .12 1.0 .040 572 000 129 000 965 000 217 000 1 300 1 700
7242-D 210 8.2677 380 14.9606 122 4.8031 3.0 .12 1.0 .040 637 000 143 000 1 120 000 252 000 1 200 1 600
7244-D 220 8.6614 400 15.7480 130 5.1181 3.0 .12 1.0 .040 650 000 146 000 1 200 000 270 000 1 200 1 600
7246-D 230 9.0551 420 16.5354 136 5.3543 3.0 .12 1.0 .040 715 000 161 000 1 340 000 301 000 1 200 1 500
7248-D 240 9.4488 440 17.3228 144 5.6693 3.0 .12 1.0 .040 780 000 175 000 1 500 000 337 000 1 100 1 400
7250-D 250 9.8425 460 18.1102 152 5.9843 4.0 .16 1.5 .060 852 000 192 000 1 660 000 373 000 1 100 1 400
7252-D 260 10.2362 480 18.8976 160 6.2992 4.0 .16 1.5 .060 904 000 203 000 1 830 000 411 000 1 000 1 400
7256-D 280 11.0236 500 19.6850 160 6.2992 4.0 .16 1.5 .060 936 000 210 000 2 000 000 450 000 1 000 1 400
7260-D 300 11.8110 540 21.2598 170 6.6929 4.0 .16 1.5 .060 1 010 000 227 000 2 200 000 495 000 960 1 300
7264-D 320 12.5984 580 22.8346 184 7.2441 4.0 .16 1.5 .060 1 060 000 238 000 2 400 000 540 000 960 1 200
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
For thrust rating multiply C by 0.81 and Co by 1.47.
3) Listed values are for machined bronze cage, ABEC-1.
For phenolic composition cage, multiply by 1.33 for both grease and oil. For phenolic composition cage, ABEC-5 or 7, multiply by 1.86 for both grease and oil. For pressed
steel cage, ABEC-1, multiply by 0.67 for grease and 0.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 274.
4) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
126
7300 Medium Series
(Single Bearings)
7300 10 .3937 35 1.3780 11 .4331 .64 .025 .60 .024 6 370 1 430 3 200 719 24 000 31 000
7301 12 .4724 37 1.4567 12 .4724 1.0 .04 .60 .024 7 020 1 580 3 750 843 19 000 25 000
7302 15 .5906 42 1.6535 13 .5118 1.0 .04 .60 .024 13 500 3 030 7 100 1 600 16 000 21 000
7303 17 .6693 47 1.8504 14 .5512 1.0 .04 .60 .024 15 900 3 570 8 650 1 940 15 000 19 000
7304 20 .7874 52 2.0472 15 .5906 1.0 .04 .60 .024 18 600 4 180 10 600 2 380 13 000 17 000
7305 25 .9843 62 2.4409 17 .6693 1.0 .04 .60 .024 21 200 4 770 13 700 3 080 11 000 14 000
7306 30 1.1811 72 2.8346 19 .7480 1.0 .04 .60 .024 28 100 6 320 18 600 4 180 9 200 12 000
7307 35 1.3780 80 3.1496 21 .8268 1.5 .06 1.0 .040 35 800 8 050 24 000 5 400 8 500 11 000
7308 40 1.5748 90 3.5433 23 .9055 1.5 .06 1.0 .040 44 200 9 940 30 500 6 860 7 300 9 500
7309 45 1.7717 100 3.9370 25 .9843 1.5 .06 1.0 .040 52 700 11 800 37 500 8 430 6 400 8 300
7310 50 1.9685 110 4.3307 27 1.0630 2.0 .08 1.0 .040 74 100 16 700 53 000 11 900 5 800 7 500
7311 55 2.1654 120 4.7244 29 1.1417 2.0 .08 1.0 .040 85 200 19 200 62 000 13 900 5 100 6 600
7312 60 2.3622 130 5.1181 31 1.2205 2.0 .08 1.0 .040 97 500 21 900 72 000 16 200 4 900 6 400
7313 65 2.5591 140 5.5118 33 1.2992 2.0 .08 1.0 .040 108 000 24 300 86 500 19 400 4 600 6 000
7314 70 2.7559 150 5.9055 35 1.3780 2.0 .08 1.0 .040 111 000 25 000 85 000 19 100 4 100 5 300
7315 75 2.9528 160 6.2992 37 1.4567 2.0 .08 1.0 .040 138 000 31 000 114 000 25 600 3 900 5 000
7316 80 3.1496 170 6.6929 39 1.5354 2.0 .08 1.0 .040 143 000 32 100 120 000 27 000 3 600 4 700
7317 85 3.3465 180 7.0866 41 1.6142 2.5 .10 1.0 .040 163 000 36 600 143 000 32 100 3 500 4 500
7318 90 3.5433 190 7.4803 43 1.6929 2.5 .10 1.0 .040 168 000 37 800 150 000 33 700 3 200 4 200
7319 95 3.7402 200 7.8740 45 1.7717 2.5 .10 1.0 .040 178 000 40 000 166 000 37 300 3 100 4 000
7320 100 3.9370 215 8.4646 47 1.8504 2.5 .10 1.0 .040 190 000 42 700 183 000 41 100 3 000 3 900
7321 105 4.1339 225 8.8583 49 1.9291 2.5 .10 1.0 .040 203 000 45 600 200 000 45 000 2 900 3 800
7322 110 4.3307 240 9.4488 50 1.9685 2.5 .10 1.0 .040 229 000 51 500 236 000 53 100 2 700 3 500
7324 120 4.7244 260 10.2362 55 2.1654 2.5 .10 1.0 .040 260 000 58 500 275 000 61 800 2 500 3 200
7326 130 5.1181 280 11.0236 58 2.2835 3.0 .12 1.0 .040 286 000 64 300 320 000 71 900 2 300 3 000
7328 140 5.5118 300 11.8110 62 2.4409 3.0 .12 1.0 .040 312 000 70 100 375 000 84 300 2 200 2 800
7330 150 5.9055 320 12.5984 65 2.5591 3.0 .12 1.0 .040 345 000 77 600 430 000 96 700 2 000 2 600
7332 160 6.2992 340 13.3858 68 2.6772 3.0 .12 1.0 .040 377 000 84 800 490 000 110 000 1 900 2 500
7334 170 6.6929 360 14.1732 72 2.8346 3.0 .12 1.0 .040 397 000 89 200 520 000 117 000 1 900 2 400
7336 180 7.0866 380 14.9606 75 2.9528 3.0 .12 1.0 .040 423 000 95 100 585 000 132 000 1 800 2 300
7338 190 7.4803 400 15.7480 78 3.0709 4.0 .16 1.5 .060 462 000 104 000 655 000 147 000 1 600 2 100
7340 200 7.8740 420 16.5354 80 3.1496 4.0 .16 1.5 .060 494 000 111 000 720 000 162 000 1 500 2 000
7342 210 8.2677 440 17.3228 84 3.3071 4.0 .16 1.5 .060 527 000 118 000 800 000 180 000 1 500 1 900
7344 220 8.6614 460 18.1102 88 3.4646 4.0 .16 1.5 .060 559 000 126 000 865 000 194 000 1 400 1 800
7348 240 9.4488 500 19.6850 95 3.7402 4.0 .16 1.5 .060 605 000 136 000 965 000 217 000 1 400 1 700
7352 260 10.2362 540 21.2598 102 4.0157 5.0 .20 2.0 .080 663 000 149 000 1 140 000 256 000 1 300 1 600
7356 280 11.0236 580 22.8346 108 4.2520 5.0 .20 2.0 .080 741 000 167 000 1 340 000 301 000 1 200 1 500
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
For thrust rating multiply C by 1.32 and C0 by 2.94.
3) Listed values are for machined bronze cage, ABEC-1.
For phenolic composition cage, multiply by 1.33 for both grease and oil. For phenolic composition cage, ABEC-5 or 7, multiply by 1.86 for both grease and oil. For pressed
steel cage, ABEC-1, multiply by 0.67 for grease and 0.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 274.
4)
Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
127
7300-D Medium Series
Duplex MRC Bearing Services
Note: ABEC-1 & 3 stocked as half-pairs where available. Use these values for back-to-back (DB) or face-to-face (DF) mounting arrangements.
Basic Radial Load Rating2) Speed Rating3)
MRC Bore Outside Width Fillet Radius 1)
7300-D 10 .3937 35 1.3780 22 .8661 .64 .025 .60 .024 10 400 2 340 6 400 1 440 19 000 25 000
7301-D 12 .4724 37 1.4567 24 .9449 1.0 .04 .60 .024 11 400 2 560 7 500 1 690 15 000 20 000
7302-D 15 .5906 42 1.6535 26 1.0236 1.0 .04 .60 .024 21 600 4 860 14 300 3 210 13 000 17 000
7303-D 17 .6693 47 1.8504 28 1.1024 1.0 .04 .60 .024 26 000 5 850 17 300 3 890 12 000 15 000
7304-D 20 .7874 52 2.0472 30 1.1811 1.0 .04 .60 .024 30 200 6 790 21 200 4 770 10 000 14 000
7305-D 25 .9843 62 2.4409 34 1.3386 1.0 .04 .60 .024 34 500 7 760 27 000 6 070 8 800 11 000
7306-D 30 1.1811 72 2.8346 38 1.4961 1.0 .04 .60 .024 46 200 10 400 37 500 8 430 7 400 9 600
7307-D 35 1.3780 80 3.1496 42 1.6535 1.5 .06 1.0 .040 58 500 13 200 48 000 10 800 6 800 8 800
7308-D 40 1.5748 90 3.5433 46 1.8110 1.5 .06 1.0 .040 71 500 16 100 61 000 13 700 5 800 7 600
7309-D 45 1.7717 100 3.9370 50 1.9685 1.5 .06 1.0 .040 85 200 19 200 75 000 16 900 5 100 6 600
7310-D 50 1.9685 110 4.3307 54 2.1260 2.0 .08 1.0 .040 121 000 27 200 106 000 23 800 4 600 6 000
7311-D 55 2.1654 120 4.7244 58 2.2835 2.0 .08 1.0 .040 140 000 31 500 125 000 28 100 4 100 5 300
7312-D 60 2.3622 130 5.1181 62 2.4409 2.0 .08 1.0 .040 159 000 35 700 146 000 32 800 3 900 5 100
7313-D 65 2.5591 140 5.5118 66 2.5984 2.0 .08 1.0 .040 178 000 40 000 173 000 38 900 3 700 4 800
7314-D 70 2.7559 150 5.9055 70 2.7559 2.0 .08 1.0 .040 182 000 40 900 170 000 38 200 3 300 4 200
7315-D 75 2.9528 160 6.2992 74 2.9134 2.0 .08 1.0 .040 225 000 50 600 228 000 51 300 3 100 4 000
7316-D 80 3.1496 170 6.6929 78 3.0709 2.0 .08 1.0 .040 234 000 52 600 240 000 54 000 2 900 3 800
7317-D 85 3.3465 180 7.0866 82 3.2283 2.5 .10 1.0 .040 265 000 59 600 285 000 64 100 2 800 3 600
7318-D 90 3.5433 190 7.4803 86 3.3858 2.5 .10 1.0 .040 276 000 62 000 300 000 67 400 2 600 3 400
7319-D 95 3.7402 200 7.8740 90 3.5433 2.5 .10 1.0 .040 291 000 65 400 325 000 73 100 2 500 3 200
7320-D 100 3.9370 215 8.4646 94 3.7008 2.5 .10 1.0 .040 312 000 70 100 365 000 82 100 2 400 3 100
7321-D 105 4.1339 225 8.8583 98 3.8583 2.5 .10 1.0 .040 332 000 74 600 400 000 89 900 2 300 3 000
7322-D 110 4.3307 240 9.4488 100 3.9370 2.5 .10 1.0 .040 371 000 83 400 475 000 107 000 2 200 2 800
7324-D 120 4.7244 260 10.2362 110 4.3307 2.5 .10 1.0 .040 423 000 95 100 560 000 126 000 2 000 2 600
7326-D 130 5.1181 280 11.0236 116 4.5669 3.0 .12 1.0 .040 468 000 105 000 640 000 144 000 1 800 2 400
7328-D 140 5.5118 300 11.8110 124 4.8819 3.0 .12 1.0 .040 507 000 114 000 735 000 165 000 1 800 2 200
7330-D 150 5.9055 320 12.5984 130 5.1181 3.0 .12 1.0 .040 559 000 126 000 865 000 194 000 1 600 2 100
7332-D 160 6.2992 340 13.3858 136 5.3543 3.0 .12 1.0 .040 618 000 139 000 965 000 217 000 1 500 2 000
7334-D 170 6.6929 360 14.1732 144 5.6693 3.0 .12 1.0 .040 650 000 146 000 1 040 000 234 000 1 500 1 900
7336-D 180 7.0866 380 14.9606 150 5.9055 3.0 .12 1.0 .040 689 000 155 000 1 160 000 261 000 1 400 1 800
7338-D 190 7.4803 400 15.7480 156 6.1417 4.0 .16 1.5 .060 761 000 171 000 1 290 000 270 000 1 300 1 700
7340-D 200 7.8740 420 16.5354 160 6.2992 4.0 .16 1.5 .060 806 000 181 000 1 430 000 321 000 1 200 1 600
7342-D 210 8.2677 440 17.3228 168 6.6142 4.0 .16 1.5 .060 852 000 192 000 1 600 000 360 000 1 200 1 500
7344-D 220 8.6614 460 18.1102 176 6.9291 4.0 .16 1.5 .060 904 000 203 000 1 730 000 389 000 1 100 1 400
7348-D 240 9.4488 500 19.6850 190 7.4803 4.0 .16 1.5 .060 975 000 219 000 1 930 000 434 000 1 000 1 400
7352-D 260 10.2362 540 21.2598 204 8.0315 5.0 .20 2.0 .080 1 080 000 243 000 2 280 000 513 000 960 1 300
7356-D 280 11.0236 580 22.8346 216 8.5039 5.0 .20 2.0 .080 1 210 000 272 000 2 650 000 596 000 960 1 200
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
For thrust rating multiply C by 0.81 and C0 by 1.47.
3) Listed values are for machined bronze cage, ABEC-1.
For phenolic composition cage, multiply by 1.33 for both grease and oil. For phenolic composition cage, ABEC-5 or 7, multiply by 1.86 for both grease and oil. For pressed
steel cage, ABEC-1, multiply by 0.67 for grease and 0.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 274.
4)
Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
128
7400 and 7400-D
Heavy Series
Caution: Single bearings are not to be used where only radial loads are present.
For two-direction thrust loads, use duplex bearings.
Note: ABEC 1 & 3 stocked as half-pairs where available. Values for -D bearings are for back-to-back or face-to-face (DF) mounting arrangements.
7403 17 .6693 62 2.4409 17 .6693 1.0 .04 .60 .024 26 000 5 850 13 700 3 080 14 000 18 000
7404 20 .7874 72 2.8346 19 .7480 1.0 .04 .60 .024 32 500 7 310 17 600 3 960 12 000 15 000
7405 25 .9843 80 3.1496 21 .8268 1.5 .06 1.0 .040 42 300 9 510 24 500 5 510 9 200 12 000
7406 30 1.1811 90 3.5433 23 .9055 1.5 .06 1.0 .040 54 000 12 100 34 000 7 640 7 700 10 000
7407 35 1.3780 100 3.9370 25 .9843 1.5 .06 1.0 .040 63 700 14 300 40 500 9 100 6 600 8 500
7408 40 1.5748 110 4.3307 27 1.0630 2.0 .08 1.0 .040 74 100 16 700 49 000 11 000 5 400 7 700
7409 45 1.7717 120 4.7244 29 1.1417 2.0 .08 1.0 .040 85 200 19 200 57 000 12 800 5 300 6 900
7410 50 1.9685 130 5.1181 31 1.2205 2.0 .08 1.0 .040 95 600 21 500 72 000 16 200 4 900 6 400
7411 55 2.1654 140 5.5118 33 1.2992 2.0 .08 1.0 .040 108 000 24 300 78 000 17 500 4 500 5 800
7412 60 2.3622 150 5.9055 35 1.3780 2.0 .08 1.0 .040 127 000 28 600 93 000 20 900 4 100 5 300
7413 65 2.5591 160 6.2992 37 1.4567 2.0 .08 1.0 .040 138 000 31 000 106 000 23 800 3 800 4 900
7414 70 2.7559 180 7.0866 42 1.6535 2.5 .10 1.0 .040 168 000 37 800 140 000 31 500 3 500 4 600
7415 75 2.9528 190 7.4803 45 1.7717 2.5 .10 1.0 .040 182 000 40 900 156 000 35 100 3 300 4 300
7416 80 3.1496 200 7.8740 48 1.8898 2.5 .10 1.0 .040 190 000 42 700 170 000 38 200 3 200 4 100
7417 85 3.3465 210 8.2677 52 2.0472 3.0 .12 1.0 .040 203 000 45 600 186 000 41 800 2 900 3 800
7418 90 3.5433 225 8.8583 54 2.1260 3.0 .12 1.0 .040 229 000 51 500 220 000 49 500 2 700 3 500
7419 95 3.7402 250 9.8425 55 2.1654 3.0 .12 1.0 .040 255 000 57 300 255 000 57 300 2 500 3 300
7420 100 3.9370 265 10.4331 60 2.3622 3.0 .12 1.0 .040 276 000 62 000 290 000 65 200 2 400 3 200
7421 105 4.1339 290 11.4173 65 2.5591 3.0 .12 1.0 .040 332 000 74 600 325 000 73 100 2 300 3 000
7422 110 4.3307 320 12.5984 70 2.7559 3.0 .12 1.0 .040 371 000 83 400 390 000 87 700 2 200 2 900
7400-D
7403-D 17 .6693 62 2.4409 34 1.3386 1.0 .04 .60 .024 42 300 9 510 27 000 6 070 11 000 14 000
7404-D 20 .7874 72 2.8346 38 1.4961 1.0 .04 .60 .024 52 700 11 800 35 500 7 980 9 600 12 000
7405-D 25 .9843 80 3.1496 42 1.6535 1.5 .06 1.0 .040 68 900 15 500 49 000 11 000 7 400 9 600
7406-D 30 1.1811 90 3.5433 46 1.8110 1.5 .06 1.0 .040 88 400 19 900 68 000 15 300 6 200 8 000
7407-D 35 1.3780 100 3.9370 50 1.9685 1.5 .06 1.0 .040 104 000 23 400 81 500 18 300 5 300 6 800
7408-D 40 1.5748 110 4.3307 54 2.1260 2.0 .08 1.0 .040 121 000 27 200 96 500 21 700 4 300 6 200
7409-D 45 1.7717 120 4.7244 58 2.2835 2.0 .08 1.0 .040 138 000 31 000 114 000 25 600 4 200 5 500
7410-D 50 1.9685 130 5.1181 62 2.4409 2.0 .08 1.0 .040 156 000 35 100 146 000 32 800 3 900 5 100
7411-D 55 2.1654 140 5.5118 66 2.5984 2.0 .08 1.0 .040 178 000 40 000 156 000 35 100 3 600 4 600
7412-D 60 2.3622 150 5.9055 70 2.7559 2.0 .08 1.0 .040 203 000 45 600 190 000 42 700 3 300 4 200
7413-D 65 2.5591 160 6.2992 74 2.9134 2.0 .08 1.0 .040 225 000 50 600 275 000 61 800 3 000 3 900
7414-D 70 2.7559 180 7.0866 84 3.3071 2.5 .10 1.0 .040 276 000 62 000 280 000 62 900 2 800 3 700
7415-D 75 2.9528 190 7.4803 90 3.5433 2.5 .10 1.0 .040 291 000 65 400 310 000 69 700 2 600 3 400
7416-D 80 3.1496 200 7.8740 96 3.7795 2.5 .10 1.0 .040 312 000 70 100 340 000 76 400 2 500 3 300
7417-D 85 3.3465 210 8.2677 104 4.0945 3.0 .12 1.0 .040 332 000 74 200 375 000 84 300 2 300 3 000
7418-D 90 3.5433 225 8.8583 108 4.2520 3.0 .12 1.0 .040 371 000 83 400 440 000 98 900 2 200 2 800
7419-D 95 3.7402 250 9.8425 110 4.3307 3.0 .12 1.0 .040 410 000 92 200 510 000 115 000 2 000 2 600
7420-D 100 3.9370 265 10.4331 120 4.7244 3.0 .12 1.0 .040 449 000 101 000 585 000 132 000 1 900 2 600
7421-D 105 4.1339 290 11.4173 130 5.1181 3.0 .12 1.0 .040 540 000 121 000 670 000 151 000 1 800 2 400
7422-D 110 4.3307 320 12.5984 140 5.5118 3.0 .12 1.0 .040 605 000 136 000 800 000 180 000 1 700 2 300
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
For thrust rating multiply C by 1.32 and Co by 2.94 (single) and C by 0.81 and C0 by 1.47 (duplex).
3) Listed values are for machined bronze cage, ABEC-1.
For phenolic composition cage, multiply by 1.33 for both grease and oil. For phenolic composition cage, ABEC-5 or 7, multiply by 1.86 for both grease and oil. For pressed
steel cage, ABEC-1, multiply by 0.67 for grease and 0.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 274.
4) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
129
MRC Bearing Services
7000 Series
29° Angular Contact Ball Bearings
Single Bearing
Life rating
3
C
()
L10 = P (millions of revolutions)
or 6 3
L10h =
10 C
60n P
() (Hours)
Case 2
Radial load (FR) = 1750
Thrust load (FA) = 2100
Equivalent load (P) = FR or 0.39 FR + 0.76 FA
FA/FR = 2100/1750 = 1.20
Since FA/FR > 0.80, P = 0.39 × 1750 + 0.76 × 2100 = 2279
3 3
11800
Life (L10) = () (
C
P
=
2279 ) = 139 × 106 Rev.
or 6 3 6 3
11800
10 C
() 10
Life (L10h) = 60n P = 60 × 2000 2279 ( )
= 1157 Hrs
Case 3
Thrust load (FA) = 2100
Equivalent load (P) = 0.39 FR + 0.76 FA
FA/FR = 2100/0 = ∞
Since FA/FR > 0.80, P = 0.76 × 2100 = 1596
3 3
11800
Life (L10) = () (
C
P
=
1596 ) = 404 × 106 Rev.
or 6 3 6 3
11800
10 C
() 10
Life (L10h) = 60n P = 60 × 2000 1596 ( )
= 3368 Hrs
131
MRC Bearing Services
7000-D Series
29° Angular Contact Ball Bearings
Duplex
FA or
P = 0.63 FR + 1.24 FA when F > 0.80 6 3
R
L10h =
10 C
60n P
() (Hours)
Tandem DT FA
P = 1.0 FR when F ≤ 0.80 P = Dynamic equivalent radial load
R
n = Speed in rpm
FA
P = 0.39 FR + 0.76 FA when F > 0.80 For DB or DF mounting:
R
C = Duplex pair dynamic radial load
P = Dynamic equivalent radial load rating (from duplex bearing tables)
FR = Radial load or
FA = Thrust load
C = Single-row dynamic radial load
rating times (i)0.7, where i = 2
For DT tandem mounting:
C = Single-row dynamic radial load
rating times (i)0.7, where i = number
of bearings in set
132
Duplex Series
7000-D Series
29° Angular Contact Ball Bearings
Duplex
MRC 7000-P Series bearings are similar in design to bearings are restricted to applications involving
7000 Series bearings, but the 7000-P Series bearings primarily thrust loads. They should not be used
have features that give them a greatly increased where the bearing will be subjected to radial load
thrust capacity. They are especially recommended exclusively, or combined radial and thrust load
for those applications where maximum thrust capacity where the radial load is predominant.
Cage Types and Materials
is required.
This heavy-duty angular contact ball bearing series is Furnished in one-piece, inner-ring land-guided,
designed with an optimum ball complement and race machined brass, phenolic/bakelite composition
groove depth, and have a 40° contact angle. 7000-P or special material.
135
7200-P Light Series
(Single Bearings) MRC Bearing Services
7200-P 10 .3937 30 1.1811 9 .3543 .64 .025 .30 .012 7 020 1 580 3 200 719 19 000 28 000
7201-P 12 .4724 32 1.2598 10 .3937 .64 .025 .30 .012 7 610 1 710 3 750 843 18 000 26 000
7202-P 15 .5906 35 1.3780 11 .4331 .64 .025 .30 .012 8 840 1 990 4 250 955 17 000 24 000
7203-P 17 .6693 40 1.5748 12 .4724 .64 .025 .30 .012 11 700 2 630 6 000 1 350 15 000 20 000
7204-P 20 .7874 47 1.8504 14 .5512 1.0 .04 .60 .024 14 800 3 330 8 300 1 870 12 000 17 000
7205-P 25 .9843 52 2.0472 15 .5906 1.0 .04 .60 .024 16 800 3 780 10 400 2 340 10 000 15 000
7206-P 30 1.1811 62 2.4409 16 .6299 1.0 .04 .60 .024 21 200 4 770 12 700 2 860 8 500 12 000
7207-P 35 1.3780 72 2.8346 17 .6693 1.0 .04 .60 .024 29 100 6 540 19 300 4 340 8 000 11 000
7208-P 40 1.5748 80 3.1496 18 .7087 1.0 .04 .60 .024 32 500 7 310 22 400 5 040 7 000 9 500
7209-P 45 1.7717 85 3.3465 19 .7480 1.0 .04 .60 .024 39 000 8 770 27 500 6 180 6 700 9 000
7210-P 50 1.9685 90 3.5433 20 .7874 1.0 .04 .60 .024 40 300 9 060 30 000 6 740 6 000 8 000
7211-P 55 2.1654 100 3.9370 21 .8268 1.5 .06 1.0 .040 48 800 11 000 37 500 8 430 5 600 7 500
7212-P 60 2.3622 110 4.3307 22 .8661 1.5 .06 1.0 .040 58 500 13 200 45 500 10 200 5 000 6 700
7213-P 65 2.5591 120 4.7244 23 .9055 1.5 .06 1.0 .040 63 700 14 300 51 000 11 500 4 500 6 000
7214-P 70 2.7559 125 4.9213 24 .9449 1.5 .06 1.0 .040 68 900 15 500 56 000 12 600 4 300 5 600
7215-P 75 2.9528 130 5.1181 25 .9843 1.5 .06 1.0 .040 71 500 16 100 60 000 13 500 4 000 5 300
7216-P 80 3.1496 140 5.5118 26 1.0236 2.0 .08 1.0 .040 83 200 18 700 71 000 16 000 3 800 5 000
7217-P 85 3.3465 150 5.9055 28 1.1024 2.0 .08 1.0 .040 95 600 21 500 83 000 18 700 3 600 4 800
7218-P 90 3.5433 160 6.2992 30 1.1811 2.0 .08 1.0 .040 108 000 24 300 95 000 21 400 3 400 4 500
7219-P 95 3.7402 170 6.6929 32 1.2598 2.0 .08 1.0 .040 124 000 27 900 110 000 24 700 3 200 4 300
7220-P 100 3.9370 180 7.0866 34 1.3386 2.0 .08 1.0 .040 130 000 29 200 125 000 28 100 3 000 4 000
7221-P 105 4.1339 190 7.4803 36 1.4173 2.0 .08 1.0 .040 143 000 32 100 129 000 29 000 2 800 3 800
7222-P 110 4.3307 200 7.8740 38 1.4961 2.0 .08 1.0 .040 153 000 34 400 156 000 35 100 2 600 3 600
7224-P 120 4.7244 215 8.4646 40 1.5748 2.0 .08 1.0 .040 165 000 37 100 163 000 36 600 2 200 3 200
7226-P 130 5.1181 230 9.0551 40 1.5748 2.5 .10 1.0 .040 186 000 41 800 193 000 43 400 1 900 2 800
7228-P 140 5.5118 250 9.8425 42 1.6535 2.5 .10 1.0 .040 199 000 44 700 216 000 48 600 1 800 2 600
7230-P 150 5.9055 270 10.6299 45 1.7717 2.5 .10 1.0 .040 216 000 48 600 260 000 58 500 1 700 2 400
7232-P 160 6.2992 290 11.4173 48 1.8898 2.5 .10 1.0 .040 238 000 53 500 280 000 62 900 1 600 2 200
7234-P 170 6.6929 310 12.2047 52 2.0472 3.0 .12 1.0 .040 265 000 59 600 335 000 75 300 1 600 2 200
7236-P 180 7.0866 320 12.5984 52 2.0472 3.0 .12 1.0 .040 276 000 62 000 355 000 79 800 1 500 2 000
7238-P 190 7.4803 340 13.3858 55 2.1654 3.0 .12 1.0 .040 302 000 67 900 405 000 91 000 1 400 1 900
7240-P 200 7.8740 360 14.1732 58 2.2835 3.0 .12 1.0 .040 319 000 71 700 440 000 98 900 1 300 1 800
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
For thrust rating multiply C by 1.75 and C0 by 3.85.
3) Listed values are for machined bronze cage, ABEC-1.
For phenolic composition cage, multiply by 1.33 for both grease and oil. For phenolic composition cage, ABEC-5 or 7, multiply by 1.86 for both grease and oil. For pressed
steel cage, ABEC-1, multiply by 0.67 for grease and 0.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 274.
4)
Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
136
7200-PD Light Series
Duplex
rb
ra
“D” indicates a duplex ground half pair matched with an identical half pair and
is followed by an additional suffix letter to describe the type of duplex. See
pages 234 and 235 for suffix description.
For duplex sets of 7000 and 9000 series bearings see page 237.
Note: ABEC - 1 & 3 stocked as half-pairs, where available. Use these values for back-to-back (DB) or face-to-face (DF) mounting arrangements.
7200-PD 10 .3937 30 1.1811 18 .7087 .64 .025 .30 .012 11 400 2 560 6 400 1 440 16 000 22 000
7201-PD 12 .4724 32 1.2598 20 .7874 .64 .025 .30 .012 12 500 2 810 7 500 1 690 13 000 18 000
7202-PD 15 .5906 35 1.3780 22 .8661 .64 .025 .30 .012 14 300 3 210 8 500 1 910 12 000 17 000
7203-PD 17 .6693 40 1.5748 24 .9449 .64 .025 .30 .012 19 000 4 270 12 000 2 700 11 000 16 000
7204-PD 20 .7874 47 1.8504 28 1.1024 1.0 .04 .60 .024 24 200 5 440 16 600 3 730 9 500 14 000
7205-PD 25 .9843 52 2.0472 30 1.1811 1.0 .04 .60 .024 27 000 6 070 20 800 4 680 8 500 12 000
7206-PD 30 1.1811 62 2.4409 32 1.2598 1.0 .04 .60 .024 34 500 7 760 25 500 5 730 7 500 10 000
7207-PD 35 1.3780 72 2.8346 34 1.3386 1.0 .04 .60 .024 47 500 10 700 39 000 8 770 6 300 8 500
7208-PD 40 1.5748 80 3.1496 36 1.4173 1.0 .04 .60 .024 52 700 11 800 45 000 10 100 5 600 7 500
7209-PD 45 1.7717 85 3.3465 38 1.4961 1.0 .04 .60 .024 62 400 14 000 55 000 12 400 5 300 7 000
7210-PD 50 1.9685 90 3.5433 40 1.5748 1.0 .04 .60 .024 65 000 14 600 60 000 13 500 4 800 6 300
7211-PD 55 2.1654 100 3.9370 42 1.6535 1.5 .06 1.0 .040 79 300 17 800 75 000 16 900 4 500 6 000
7212-PD 60 2.3622 110 4.3307 44 1.7323 1.5 .06 1.0 .040 95 600 21 500 91 600 20 600 4 000 5 300
7213-PD 65 2.5591 120 4.7244 46 1.8110 1.5 .06 1.0 .040 104 000 23 400 100 000 22 500 3 600 4 800
7214-PD 70 2.7559 125 4.9213 48 1.8898 1.5 .06 1.0 .040 112 000 25 200 112 000 25 200 3 400 4 500
7215-PD 75 2.9528 130 5.1181 50 1.9685 1.5 .06 1.0 .040 117 000 26 300 120 000 27 000 3 200 4 300
7216-PD 80 3.1496 140 5.5118 52 2.0472 2.0 .08 1.0 .040 135 000 30 300 140 000 31 500 3 000 4 000
7217-PD 85 3.3465 150 5.9055 56 2.2047 2.0 .08 1.0 .040 156 000 35 100 166 000 37 300 2 800 3 800
7218-PD 90 3.5433 160 6.2992 60 2.3622 2.0 .08 1.0 .040 178 000 40 000 190 000 42 700 2 600 3 600
7219-PD 95 3.7402 170 6.6929 64 2.5197 2.0 .08 1.0 .040 199 000 44 700 220 000 49 500 2 400 3 400
7220-PD 100 3.9370 180 7.0866 68 2.6772 2.0 .08 1.0 .040 212 000 47 700 250 000 56 200 2 200 3 200
7221-PD 105 4.1339 190 7.4803 72 2.8346 2.0 .08 1.0 .040 229 000 51 500 260 000 58 500 2 000 3 000
7222-PD 110 4.3307 200 7.8740 76 2.9921 2.0 .08 1.0 .040 251 000 56 400 310 000 69 700 1 900 2 800
7224-PD 120 4.7244 215 8.4646 80 3.1496 2.0 .08 1.0 .040 270 000 60 700 325 000 73 100 1 700 2 400
7226-PD 130 5.1181 230 9.0551 80 3.1496 2.5 .10 1.0 .040 302 000 67 900 390 000 87 700 1 700 2 400
7228-PD 140 5.5118 250 9.8425 84 3.3071 2.5 .10 1.0 .040 319 000 71 700 430 000 96 700 1 600 2 200
7230-PD 150 5.9055 270 10.6299 90 3.5433 2.5 .10 1.0 .040 351 000 78 900 520 000 117 000 1 500 2 000
7232-PD 160 6.2992 290 11.4173 96 3.7795 2.5 .10 1.0 .040 390 000 87 700 560 000 126 000 1 300 1 700
7234-PD 170 6.6929 310 12.2047 104 4.0945 3.0 .12 1.0 .040 436 000 98 000 655 000 147 000 1 200 1 600
7236-PD 180 7.0866 320 12.5984 104 4.0945 3.0 .12 1.0 .040 449 000 101 000 710 000 160 000 1 100 1 500
7238-PD 190 7.4803 340 13.3858 110 4.3307 3.0 .12 1.0 .040 488 000 110 000 815 000 183 000 1 100 1 500
7240-PD 200 7.8740 360 14.1732 116 4.5669 3.0 .12 1.0 .040 520 000 117 000 880 000 198 000 1 000 1 400
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
For thrust rating multiply C by 1.08 and C0 by 1.93.
3) Listed values are for machined bronze cage, ABEC-1.
For phenolic composition cage, multiply by 1.33 for both grease and oil. For phenolic composition cage, ABEC-5 or 7, multiply by 1.86 for both grease and oil. For pressed
steel cage, ABEC-1, multiply by 0.67 for grease and 0.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 274.
4)
Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
137
7300-P Medium Series
(Single Bearings) MRC Bearing Services
7300-P 10 .3937 35 1.3780 11 .4331 .64 .025 .30 .012 9 360 2 100 4 150 933 18 000 26 000
7301-P 12 .4724 37 1.4567 12 .4724 1.0 .04 .60 .024 11 200 2 520 5 000 1 120 17 000 24 000
7302-P 15 .5906 42 1.6535 13 .5118 1.0 .04 .60 .024 12 700 2 860 6 100 1 370 15 000 20 000
7303-P 17 .6693 47 1.8504 14 .5512 1.0 .04 .60 .024 16 800 3 780 8 500 1 910 13 000 18 000
7304-P 20 .7874 52 2.0472 15 .5906 1.0 .04 .60 .024 18 600 4 180 9 500 2 140 11 000 16 000
7305-P 25 .9843 62 2.4409 17 .6693 1.0 .04 .60 .024 24 200 5 440 13 400 3 010 9 000 13 000
7306-P 30 1.1811 72 2.8346 19 .7480 1.0 .04 .60 .024 32 500 7 310 19 600 4 410 8 000 11 000
7307-P 35 1.3780 80 3.1496 21 .8268 1.5 .06 1.0 .040 39 700 8 920 24 500 5 510 7 500 10 000
7308-P 40 1.5748 90 3.5433 23 .9055 1.5 .06 1.0 .040 47 500 10 700 30 500 6 860 6 700 9 000
7309-P 45 1.7717 100 3.9370 25 .9843 1.5 .06 1.0 .040 59 200 13 300 40 000 8 990 6 000 8 000
7310-P 50 1.9685 110 4.3307 27 1.0630 2.0 .08 1.0 .040 68 900 15 500 52 000 11 700 5 300 7 000
7311-P 55 2.1654 120 4.7244 29 1.1417 2.0 .08 1.0 .040 79 300 17 800 56 000 12 600 4 800 6 300
7312-P 60 2.3622 130 5.1181 31 1.2205 2.0 .08 1.0 .040 90 400 20 300 64 000 14 400 4 500 6 000
7313-P 65 2.5591 140 5.5118 33 1.2992 2.0 .08 1.0 .040 101 000 22 700 80 000 18 000 4 300 5 600
7314-P 70 2.7559 150 5.9055 35 1.3780 2.0 .08 1.0 .040 117 000 26 300 93 000 20 900 3 800 5 000
7315-P 75 2.9528 160 6.2992 37 1.4567 2.0 .08 1.0 .040 127 000 28 600 100 000 22 500 3 600 4 800
7316-P 80 3.1496 170 6.6929 39 1.5354 2.0 .08 1.0 .040 138 000 31 000 110 000 24 700 3 400 4 500
7317-P 85 3.3465 180 7.0866 41 1.6142 2.5 .10 1.0 .040 148 000 33 300 122 000 27 400 3 200 4 300
7318-P 90 3.5433 190 7.4803 43 1.6929 2.5 .10 1.0 .040 159 000 35 700 137 000 30 800 3 000 4 000
7319-P 95 3.7402 200 7.8740 45 1.7717 2.5 .10 1.0 .040 168 000 37 800 150 000 33 700 2 800 3 800
7320-P 100 3.9370 215 8.4646 47 1.8504 2.5 .10 1.0 .040 190 000 42 700 190 000 42 700 2 600 3 600
7321-P 105 4.1339 225 8.8583 49 1.9291 2.5 .10 1.0 .040 203 000 45 600 196 000 44 100 2 400 3 400
7322-P 110 4.3307 240 9.4488 50 1.9685 2.5 .10 1.0 .040 212 000 47 700 228 000 51 300 2 200 3 200
7324-P 120 4.7244 260 10.2362 55 2.1654 2.5 .10 1.0 .040 238 000 53 500 265 000 59 600 1 900 2 800
7326-P 130 5.1181 280 11.0236 58 2.2835 3.0 .12 1.0 .040 276 000 62 000 305 000 68 600 1 800 2 600
7328-P 140 5.5118 300 11.8110 62 2.4409 3.0 .12 1.0 .040 302 000 67 900 345 000 77 600 1 700 2 400
7330-P 150 5.9055 320 12.5984 65 2.5591 3.0 .12 1.0 .040 325 000 73 100 390 000 87 700 1 600 2 200
7332-P 160 6.2992 340 13.3858 68 2.6772 3.0 .12 1.0 .040 345 000 77 600 425 000 95 500 1 500 2 000
7334-P 170 6.6929 360 14.1732 72 2.8346 3.0 .12 1.0 .040 377 000 84 800 490 000 110 000 1 400 1 900
7336-P 180 7.0866 380 14.9606 75 2.9528 3.0 .12 1.0 .040 403 000 90 600 540 000 121 000 1 300 1 800
7338-P 190 7.4803 400 15.7480 78 3.0709 4.0 .16 1.5 .060 416 000 93 500 570 000 128 000 1 200 1 700
7340-P 200 7.8740 420 16.5354 80 3.1496 4.0 .16 1.5 .060 449 000 101 000 655 000 147 000 1 100 1 600
1)Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
For thrust rating multiply C by 1.75 and C0 by 3.85.
3)Listed values are for machined bronze cage, ABEC-1.
For phenolic composition cage, multiply by 1.33 for both grease and oil. For phenolic composition cage, ABEC-5 or 7, multiply by 1.86 for both grease and oil. For pressed
steel cage, ABEC-1, multiply by 0.67 for grease and 0.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 274.
4) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
138
7300-PD Medium Series
Duplex
rb
ra
“D” indicates a duplex ground half pair matched with an identical half pair and is
followed by an additional suffix letter to describe the type of duplex. See pages 234
and 235 for suffix description.
For duplex sets of 7000 and 9000 series bearings see page 237.
Use these values for back-to-back (DB) or face-to-face (DF) mounting arrangements.
Note: ABEC-1 & 3 stocked as half-pairs, where available.
7300-PD 10 .3937 35 1.3780 22 .8661 .64 .025 .30 .012 15 300 3 440 8 300 1 870 15 000 21 000
7301-PD 12 .4724 37 1.4567 24 .9449 1.0 .04 .60 .024 18 200 4 090 10 200 2 290 14 000 19 000
7302-PD 15 .5906 42 1.6535 26 1.0236 1.0 .04 .60 .024 20 300 4 560 12 200 2 740 11 000 16 000
7303-PD 17 .6693 47 1.8504 28 1.1024 1.0 .04 .60 .024 27 600 6 200 17 000 3 820 9 500 14 000
7304-PD 20 .7874 52 2.0472 30 1.1811 1.0 .04 .60 .024 30 200 6 790 19 000 4 270 9 000 13 000
7305-PD 25 .9843 62 2.4409 34 1.3386 1.0 .04 .60 .024 39 000 8 770 27 000 6 070 7 500 10 000
7306-PD 30 1.1811 72 2.8346 38 1.4961 1.0 .04 .60 .024 52 700 11 800 39 000 8 770 6 700 9 000
7307-PD 35 1.3780 80 3.1496 42 1.6535 1.5 .06 1.0 .040 63 700 14 300 49 000 11 000 6 000 8 000
7308-PD 40 1.5748 90 3.5433 46 1.8110 1.5 .06 1.0 .040 76 100 17 100 61 000 13 700 5 300 7 000
7309-PD 45 1.7717 100 3.9370 50 1.9685 1.5 .06 1.0 .040 97 500 21 900 80 000 18 000 4 800 6 300
7310-PD 50 1.9685 110 4.3307 54 2.1260 2.0 .08 1.0 .040 112 000 25 200 104 000 23 400 4 300 5 600
7311-PD 55 2.1654 120 4.7244 58 2.2835 2.0 .08 1.0 .040 130 000 29 200 112 000 25 200 3 800 5 000
7312-PD 60 2.3622 130 5.1181 62 2.4409 2.0 .08 1.0 .040 148 000 33 300 129 000 29 000 3 600 4 800
7313-PD 65 2.5591 140 5.5118 66 2.5984 2.0 .08 1.0 .040 165 000 37 100 160 000 36 000 3 200 4 300
7314-PD 70 2.7559 150 5.9055 70 2.7559 2.0 .08 1.0 .040 190 000 42 700 186 000 41 800 3 000 4 000
7315-PD 75 2.9528 160 6.2992 74 2.9134 2.0 .08 1.0 .040 208 000 46 800 200 000 45 000 2 800 3 800
7316-PD 80 3.1496 170 6.6929 78 3.0709 2.0 .08 1.0 .040 225 000 50 600 220 000 49 500 2 600 3 600
7317-PD 85 3.3465 180 7.0866 82 3.2283 2.5 .10 1.0 .040 238 000 53 500 245 000 55 100 2 400 3 400
7318-PD 90 3.5433 190 7.4803 86 3.3858 2.5 .10 1.0 .040 255 000 57 300 270 000 60 700 2 200 3 200
7319-PD 95 3.7402 200 7.8740 90 3.5433 2.5 .10 1.0 .040 276 000 62 000 300 000 67 400 2 000 3 000
7320-PD 100 3.9370 215 8.4646 94 3.7008 2.5 .10 1.0 .040 307 000 69 000 380 000 85 400 1 900 2 800
7321-PD 105 4.1339 225 8.8583 98 3.8583 2.5 .10 1.0 .040 325 000 73 100 390 000 87 700 1 800 2 600
7322-PD 110 4.3307 240 9.4488 100 3.9370 2.5 .10 1.0 .040 345 000 77 600 455 000 102 000 1 700 2 400
7324-PD 120 4.7244 260 10.2362 110 4.3307 2.5 .10 1.0 .040 390 000 87 700 530 000 119 000 1 600 2 200
7326-PD 130 5.1181 280 11.0236 116 4.5669 3.0 .12 1.0 .040 449 000 101 000 610 000 137 000 1 500 2 000
7328-PD 140 5.5118 300 11.8110 124 4.8819 3.0 .12 1.0 .040 488 000 110 000 695 000 156 000 1 400 1 900
7330-PD 150 5.9055 320 12.5984 130 5.1181 3.0 .12 1.0 .040 540 000 121 000 780 000 175 000 1 200 1 700
7332-PD 160 6.2992 340 13.3858 136 5.3543 3.0 .12 1.0 .040 553 000 124 000 850 000 191 000 1 200 1 600
7334-PD 170 6.6929 360 14.1732 144 5.6693 3.0 .12 1.0 .040 605 000 136 000 965 000 217 000 1 000 1 500
7336-PD 180 7.0866 380 14.9606 150 5.9055 3.0 .12 1.0 .040 650 000 146 000 1 100 000 247 000 950 1 400
7338-PD 190 7.4803 400 15.7480 156 6.1417 4.0 .16 1.5 .060 676 000 152 000 1 160 000 261 000 950 1 400
7340-PD 200 7.8740 420 16.5354 160 6.2992 4.0 .16 1.5 .060 741 000 167 000 1 320 000 297 000 880 1 300
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
For thrust rating multiply C by 1.08 and C0 by 1.93.
3) Listed values are for machined bronze cage, ABEC-1.
For phenolic composition cage, multiply by 1.33 for both grease and oil. For phenolic composition cage, ABEC-5 or 7, multiply by 1.86 for both grease and oil. For pressed
steel cage, ABEC-1, multiply by 0.67 for grease and 0.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 274.
4)
Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
139
7400-P and 7400-PD
Heavy Series MRC Bearing Services
7405P 25 .9843 80 3.1496 21 .8268 1.5 .060 1.0 .040 39 700 8 920 23 600 5 310 7 000 10 000
7406P 30 1.1811 90 3.5433 23 .9055 1.5 .060 1.0 .040 47 500 10 700 29 000 6 520 6 300 9 000
7407P 35 1.3780 100 3.9370 25 .9843 1.5 .060 1.0 .040 60 500 13 600 38 000 8 540 5 600 7 500
7408P 40 1.5748 110 4.3307 27 1.0630 2.0 .080 1.0 .040 70 200 15 800 45 000 10 100 5 300 7 000
7409P 45 1.7717 120 4.7244 29 1.1417 2.0 .080 1.0 .040 85 200 19 200 55 000 12 400 4 800 6 300
7410P 50 1.9685 130 5.1181 31 1.2205 2.0 .080 1.0 .040 95 600 21 500 64 000 14 400 4 300 6 000
7411P 55 2.1654 140 5.5118 33 1.2992 2.0 .080 1.0 .040 111 000 25 000 76 500 17 200 4 000 5 600
7412P 60 2.3622 150 5.9055 35 1.3780 2.0 .080 1.0 .040 119 000 26 800 86 500 19 400 3 600 5 000
7413P 65 2.5591 160 6.2992 37 1.4567 2.0 .080 1.0 .040 130 000 29 200 96 500 21 700 3 400 4 800
7414P 70 2.7559 180 7.0866 42 1.6535 2.5 .100 1.0 .040 159 000 35 700 127 000 28 600 3 000 4 300
7415P 75 2.9528 190 7.4803 45 1.7717 2.5 .100 1.0 .040 168 000 37 800 140 000 31 500 2 800 4 000
7416P 80 3.1496 200 7.8740 48 1.8898 2.5 .100 1.0 .040 183 000 41 100 156 000 35 100 2 600 3 800
7417P 85 3.3465 210 8.2677 52 2.0472 3.0 .120 1.0 .040 190 000 42 700 166 000 37 300 2 500 3 600
7418P 90 3.5433 225 8.8583 54 2.1260 3.0 .120 1.0 .040 216 000 48 600 200 000 45 000 2 400 3 400
7419P 95 3.7402 250 9.8425 55 2.1654 3.0 .120 1.0 .040 251 000 56 400 245 000 55 100 2 200 3 000
7420P 100 3.9370 265 10.4331 60 2.3622 3.0 .120 1.0 .040 276 000 62 000 275 000 61 800 2 000 2 800
7421P 105 4.1339 290 11.4173 65 2.5591 3.0 .120 1.0 .040 265 000 59 600 280 000 62 900 1 900 2 600
7400-PD
7405PD 25 .9843 80 3.1496 42 1.6535 1.5 .060 1.0 .040 65 000 14 500 47 500 10 600 5 600 8 000
7406PD 30 1.1811 90 3.5433 46 1.8110 1.5 .060 1.0 .040 78 000 17 400 58 500 13 000 5 000 7 200
7407PD 35 1.3780 100 3.9370 50 1.9685 1.5 .060 1.0 .040 97 500 22 100 76 500 17 100 4 500 6 000
7408PD 40 1.5748 110 4.3307 54 2.1260 2.0 .080 1.0 .040 114 000 25 700 90 000 20 200 4 300 5 600
7409PD 45 1.7717 120 4.7244 58 2.2835 2.0 .080 1.0 .040 138 000 31 200 110 000 24 800 3 800 5 000
7410PD 50 1.9685 130 5.1181 62 2.4409 2.0 .080 1.0 .040 156 000 34 900 129 000 28 800 3 400 4 800
7411PD 55 2.1654 140 5.5118 66 2.5984 2.0 .080 1.0 .040 182 000 40 600 153 000 34 400 3 200 4 500
7412PD 60 2.3622 150 5.9055 70 2.7559 2.0 .080 1.0 .040 195 000 43 600 173 000 38 800 2 800 4 000
7413PD 65 2.5591 160 6.2992 74 2.9134 2.0 .080 1.0 .040 212 000 47 400 193 000 43 400 2 700 3 800
7414PD 70 2.7559 180 7.0866 84 3.3071 2.5 .100 1.0 .040 260 000 58 000 255 000 57 200 2 400 3 400
7415PD 75 2.9528 190 7.4803 90 3.5433 2.5 .100 1.0 .040 276 000 61 400 280 000 63 000 2 200 3 200
7416PD 80 3.1496 200 7.8740 96 3.7795 2.5 .100 1.0 .040 296 000 66 500 310 000 69 700 2 000 3 000
7417PD 85 3.3465 210 8.2677 104 4.0945 3.0 .120 1.0 .040 307 000 69 400 335 000 74 600 2 000 2 800
7418PD 90 3.5433 225 8.8583 108 4.2520 3.0 .120 1.0 .040 351 000 78 900 400 000 89 900 1 900 2 700
7419PD 95 3.7402 250 9.8425 110 4.3307 3.0 .120 1.0 .040 410 000 92 200 490 000 110 000 1 800 2 400
7420PD 100 3.9370 265 10.4331 120 4.7244 3.0 .120 1.0 .040 449 000 101 000 550 000 124 000 1 600 2 200
7421PD 105 4.1339 290 11.4173 130 5.1181 3.0 .120 1.0 .040 436 000 96 900 560 000 126 000 1 500 2 000
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
For thrust rating multiply C by 1.75 and C0 by 3.85 (single) and C by 1.08 and C0 by 1.93 (duplex).
3) Listed values are for machined bronze cage, ABEC-1.
For phenolic composition cage, multiply by 1.33 for both grease and oil. For phenolic composition cage, ABEC-5 or 7, multiply by 1.86 for both grease and oil. For pressed
steel cage, ABEC-1, multiply by 0.67 for grease and 0.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For a
more complete explanation, see page 276.
4)
Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
140
141
MRC Bearing Services
7000-P Series
40° Angular Contact Ball Bearings
Single Bearing
Life rating
3
L10 = (CP) (millions of revolutions)
Ball Bearings
7213P 44.55 7313P 111.40
7214P 53.74 7314P 144.60
7215P 61.15 7315P 182.70
7216P 84.07 7316P 215.80
7217P 112.90 7317P 269.40
Satisfactory operation of angular contact ball bearings 7218P 148.50 7318P 332.30
requires sufficient traction forces between the balls and races 7219P 191.90 7319P 405.70
7220P 224.10 7320P 629.40
to minimize damage caused by sliding or skidding. This is 7221P 282.70 7321P 673.40
particularly important at high speeds where the inertia forces 7222P 352.10 7322P 904.70
7224P 450.50 7324P 1227.00
of the balls and cage and the viscous drag in the lubricant 7226P 604.70 7326P 1631.00
can have a detrimental influence on the rolling conditions. 7228P 761.60 7328P 2128.00
7230P 1074.00 7330P 2731.00
7232P 1314.00 7332P 3198.00
The minimum required thrust load can be determined from 7234P 1777.00 7334P 3717.00
7236P 1981.00 7336P 5006.00
the following formula. 7238P 2499.00 7338P 5739.00
7240P 3081.00 7340P 7048.00
n 2
(
FA = A 1000 Newtons ) 7405P
7406P
7407P
10.80
16.17
27.54
or 7408P 38.49
n 2
FA = 0.2248 A
1000 (
Pounds ) 7409P
7410P
7411P
58.46
78.46
111.70
7412P 143.60
Where, FA = Minimum thrust load 7413P 181.90
A = Bearing design factor listed in the following tables 7414P 309.20
7415P 376.40
n = Speed in RPM 7416P 452.40
7417P 542.30
Note: For Duplex Bearings mounted in tandem, multiply the single-bearing thrust value by the
7418P 724.60
7419P 1083.00
number of bearings in tandem. 7420P 1387.00
7421P 1546.00
142
7000-P Series
40° Angular Contact Ball Bearings
Single Bearing
Case 1
Radial load (FR) = 1750
Thrust load (FA) = 1960
FA/FR = 1960/1750 = 1.12
Since FA/FR < 1.14, equivalent load (P) = FR = 1750
3 3
Life (L10) = (CP) = (13300
1750 )
= 439 × 106 Rev.
or 6 3 6 3
13300
10 C
() 10
Life (L10h) = 60n P = 60 × 2000 1750 ( )
= 3658 Hrs
Case 2
Radial load (FR) = 1750
Thrust load (FA) = 2450
FA/FR = 2450/1750 = 1.40
Since FA/FR > 1.14, equivalent load (P) = 0.35 FR + 0.57 FA
P = 0.35 × 1750 + 0.57 × 2450 = 2009
3 3
Life (L10) = (CP) = (13300
2009 )
= 290 × 106 Rev.
or 6 3 6 3
13300
10 C
() 10
Life (L10h) = 60n P = 60 × 2000 2009 ( )
= 2418 Hrs
Case 3
Thrust load (FA) = 2450
FA/FR = 2450/0 = ∞
Since FA/FR > 1.14, equivalent load (P) = 0.35 FR + 0.57 FA
P = 0.57 × 2450 = 1397
3 3
Life (L10) = (CP) = (13300
1397 )
= 863 × 106 Rev.
or 6 3 6 3
13300
10 C
() 10
Life (L10h) = 60n P = 60 × 2000 1397 ( )
= 7191 Hrs
143
MRC Bearing Services
7000-PD Series
40° Angular Contact Ball Bearings
Duplex
FA or
P = 0.57 FR + 0.93 FA when F > 1.14 6 3
R
L10h =
10 C
60n P
() (Hours)
Tandem DT FA
P = 1.0 FR when F ≤ 1.14 P = Dynamic equivalent radial load
R
n = Speed in rpm
FA
P = 0.35 FR + 0.57 FA when F > 1.14 For DB or DF mounting:
R
C = Duplex pair dynamic radial load
P = Dynamic equivalent radial load rating (from duplex bearing tables)
FR = Radial load or
FA = Thrust load C = Single-row dynamic radial load
rating times (i)0.7, where i = 2
For DT tandem mounting:
C = Single-row dynamic radial load
rating times (i)0.7, where i = number
of bearings in set
144
7000-PD Series
40° AngularContact Ball Bearings
Duplex
Case 3 Case 4
Thrust load (FA) = 2450 Radial load (FR) = 1750
FA/FR = 2450/0 = ∞ FA/FR = 0/1750 = 0
Since FA/FR > 1.14, equivalent load Since FA/FR < 1.14, equivalent load
(P) = 0.57 FR + 0.93 FA = 0.93 × 2450 = 2279 (P) = 1.0 FR + 0.55 FA = 1.0 × 1750 = 1750
3 3 3 3
21900 21900
() (
Life (L10) = C =
P 2279 ) = 887 × 106 Rev. () (
Life (L10) = C =
P 1750 ) = 1960 × 106 Rev.
3
21900
or 6
()
10 C
3
10
6
Life (L10h) = 60n P = 60 × 2000 2279 ( 21900
)
3 or 6
()
10 C
3
10
6
Life (L10h) = 60n P = 60 × 2000 1750
( )
= 7395 Hrs = 16332 Hrs
145
146
7000-PJ Series Single-Row 40°
Angular Contact Ball Bearings
MRC angular contact ball bearings with a PJ suffix have MRC 7000-PJ Series bearings are available with either
one heavy race shoulder and one counterbored race pressed brass or machined brass, ball centered cages.
shoulder on the outer ring; opposing one heavy race The low shoulder diameters on the nonthrust sides of
shoulder and one counterbored race shoulder on the the inner and outer rings, combined with large
inner ring. Because of this construction, it is possible clearances between the land diameters and the cage,
for this bearing to incorporate a greater number of allow for large quantities of oil to flow through these
balls than a deep groove, nonfilling notch bearing. bearings. The increased oil flow reduces operating
The combination of maximum ball complement, temperature and theoretically increases bearing life.
optimum race groove depth, and the 40° contact
angle results in high thrust load carrying capacity. ABEC-3 bore tolerances reduce the range of
interference fits between the shaft and bearing bore.
MRC 7000-PJ Series bearings are particularly suitable These tighter tolerances result in closer control of
for positions where the thrust is always present in one preload and minimize the risk of thermal runaway.
direction. They should not be used where the bearing
is subjected to radial load only; or combined radial
and thrust load where the radial load is predominant.
When heavy thrust must be taken in both directions,
the PJD series angular contact ball bearings may be
mounted in a back-to-back or face-to-face duplex
arrangement with another angular contact bearing.
147
7200-PJ Light Series and
7200-PJD Light Series, Duplex MRC Bearing Services
7205-PJ 25 .9843 52 2.0472 15 .5906 1.0 .04 .60 .024 15 600 3 510 10 200 2 290 10 000 15 000
7206-PJ 30 1.1811 62 2.4409 16 .6299 1.0 .04 .60 .024 23 800 5 350 15 600 3 510 8 500 12 000
7207-PJ 35 1.3780 72 2.8346 17 .6693 1.0 .04 .60 .024 30 700 6 900 20 800 4 680 8 000 11 000
7208-PJ 40 1.5748 80 3.1496 18 .7087 1.0 .04 .60 .024 36 400 8 180 26 000 5 850 7 000 9 500
7209-PJ 45 1.7717 85 3.3465 19 .7480 1.0 .04 .60 .024 37 700 8 480 28 000 6 300 6 700 9 000
7210-PJ 50 1.9685 90 3.5433 20 .7874 1.0 .04 .60 .024 39 000 8 770 30 500 6 860 6 000 8 000
7211-PJ 55 2.1654 100 3.9370 21 .8268 1.5 .06 1.0 .040 48 800 11 000 38 000 8 540 5 600 7 500
7212-PJ 60 2.3622 110 4.3307 22 .8661 1.5 .06 1.0 .040 57 200 12 900 45 500 10 200 5 000 6 700
7213-PJ 65 2.5591 120 4.7244 23 .9055 1.5 .06 1.0 .040 66 300 14 900 54 000 12 100 4 500 6 000
7214-PJ 70 2.7559 125 4.9213 24 .9449 1.5 .06 1.0 .040 71 500 16 100 60 000 13 500 4 300 5 600
7215-PJ 75 2.9528 130 5.1181 25 .9843 1.5 .06 1.0 .040 72 800 16 400 64 000 14 400 4 000 5 300
7216-PJ 80 3.1496 140 5.5118 26 1.0236 2.0 .08 1.0 .040 83 200 18 700 73 500 16 500 3 800 5 000
7217-PJ 85 3.3465 150 5.9055 28 1.1024 2.0 .08 1.0 .040 95 600 21 500 83 000 18 700 3 600 4 800
7218-PJ 90 3.5433 160 6.2992 30 1.1811 2.0 .08 1.0 .040 108 000 24 300 96 500 21 700 3 400 4 500
7200-PJD
7205-PJD 25 .9843 52 2.0472 30 1.1811 1.0 .04 .60 .024 25 100 5 640 20 400 4 590 8 500 12 000
7206-PJD 30 1.1811 62 2.4409 32 1.2598 1.0 .04 .60 .024 39 000 8 770 31 000 6 970 7 500 10 000
7207-PJD 35 1.3780 72 2.8346 34 1.3386 1.0 .04 .60 .024 50 700 11 400 41 500 9 330 6 300 8 500
7208-PJD 40 1.5748 80 3.1496 36 1.4173 1.0 .04 .60 .024 59 200 13 300 52 000 11 700 5 600 7 500
7209-PJD 45 1.7717 85 3.3465 38 1.4961 1.0 .04 .60 .024 61 800 13 900 56 000 12 600 5 300 7 000
7210-PJD 50 1.9685 90 3.5433 40 1.5748 1.0 .04 .60 .024 63 700 14 300 61 000 13 700 4 800 6 300
7211-PJD 55 2.1654 100 3.9370 42 1.6535 1.5 .06 1.0 .040 78 000 17 500 76 500 17 200 4 500 6 000
7212-PJD 60 2.3622 110 4.3307 44 1.7323 1.5 .06 1.0 .040 93 600 21 000 91 500 20 600 4 000 5 300
7213-PJD 65 2.5591 120 4.7244 46 1.8110 1.5 .06 1.0 .040 108 000 24 300 108 000 24 300 3 600 4 800
7214-PJD 70 2.7559 125 4.9213 48 1.8898 1.5 .06 1.0 .040 114 000 25 600 118 000 26 500 3 400 4 500
7215-PJD 75 2.9528 130 5.1181 50 1.9685 1.5 .06 1.0 .040 119 000 26 800 127 000 28 600 3 200 4 300
7216-PJD 80 3.1496 140 5.5118 52 2.0472 2.0 .08 1.0 .040 135 000 30 400 146 000 32 800 3 000 4 000
7217-PJD 85 3.3465 150 5.9055 56 2.2047 2.0 .08 1.0 .040 156 000 35 100 166 000 37 300 2 800 3 800
7218-PJD 90 3.5433 160 6.2992 60 2.3622 2.0 .08 1.0 .040 178 000 40 000 193 000 43 400 2 600 3 600
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
For thrust rating multiply C by 1.75 and C0 by 3.85 (single) and C by 1.08 and C0 by 1.93 (duplex).
3) Listed values are for pressed brass and steel or polyamide cage.
The values have been determined through historical application and practice. For a more complete explanation, see page 274.
4) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
148
7300-PJ Medium Series and 7300-PJD
Medium Series, Duplex
7304-PJ 20 .7874 52 2.0472 15 .5906 1.0 .04 .60 .024 19 000 4 270 10 400 2 340 11 000 16 000
7305-PJ 25 .9843 62 2.4409 17 .6693 1.0 .04 .60 .024 26 000 5 850 15 600 3 510 9 000 13 000
7306-PJ 30 1.1811 72 2.8346 19 .7480 1.0 .04 .60 .024 34 500 7 760 21 200 4 770 8 000 11 000
7307-PJ 35 1.3780 80 3.1496 21 .8268 1.5 .06 1.0 .040 39 000 8 770 24 500 5 510 7 500 10 000
7308-PJ 40 1.5748 90 3.5433 23 .9055 1.5 .06 1.0 .040 49 400 11 100 33 500 7 530 6 700 9 000
7309-PJ 45 1.7717 100 3.9370 25 .9843 1.5 .06 1.0 040 60 500 13 600 41 500 9 330 6 000 8 000
7310-PJ 50 1.9685 110 4.3307 27 1.0630 2.0 .08 1.0 .040 74 100 16 700 51 000 11 500 5 300 7 000
7311-PJ 55 2.1654 120 4.7244 29 1.1417 2.0 .08 1.0 .040 85 200 19 200 60 000 13 500 4 800 6 300
7312-PJ 60 2.3622 130 5.1181 31 1.2205 2.0 .08 1.0 .040 95 600 21 500 69 500 15 600 4 500 6 000
7313-PJ 65 2.5591 140 5.5118 33 1.2992 2.0 .08 1.0 .040 108 000 24 300 80 000 18 000 4 300 5 600
7314-PJ 70 2.7559 150 5.9055 35 1.3780 2.0 .08 1.0 .040 119 000 26 800 90 000 20 200 3 800 5 000
7315-PJ 75 2.9528 160 6.2992 37 1.4567 2.0 .08 1.0 .040 133 000 29 900 106 000 23 800 3 600 4 800
7316-PJ 80 3.1496 170 6.6929 39 1.5354 2.0 .08 1.0 .040 143 000 32 200 118 000 26 500 3 400 4 500
7317-PJ 85 3.3465 180 7.0866 41 1.6142 2.5 .10 1.0 .040 153 000 34 400 132 000 29 700 3 200 4 300
7318-PJ 90 3.5433 190 7.4803 43 1.6929 2.5 .10 1.0 .040 165 000 37 100 146 000 32 800 3 000 4 000
7319-PJ 95 3.7402 200 7.8740 45 1.7717 2.5 .10 1.0 .040 178 000 40 000 163 000 36 600 2 800 3 800
7300-PJD
7304-PJD 20 .7874 52 2.0472 30 1.1811 1.0 .04 .60 .024 30 700 6 900 20 800 4 680 9 000 13 000
7305-PJD 25 .9843 62 2.4409 34 1.3386 1.0 .04 .60 .024 42 300 9 510 31 000 6 970 7 500 10 000
7306-PJD 30 1.1811 72 2.8346 38 1.4961 1.0 .04 .60 .024 55 900 12 600 42 500 9 550 6 700 9 000
7307-PJD 35 1.3780 80 3.1496 42 1.6535 1.5 .06 1.0 .040 62 400 14 000 49 000 11 000 6 000 8 000
7308-PJD 40 1.5748 90 3.5433 46 1.8110 1.5 .06 1.0 .040 79 300 17 800 65 500 14 700 5 300 7 000
7309-PJD 45 1.7717 100 3.9370 50 1.9685 1.5 .06 1.0 .040 97 500 21 900 81 500 18 300 4 800 6 300
7310-PJD 50 1.9685 110 4.3307 54 2.1260 2.0 .08 1.0 .040 119 000 26 800 102 000 22 900 4 300 5 600
7311-PJD 55 2.1654 120 4.7244 58 2.2835 2.0 .08 1.0 .040 138 000 31 000 120 000 27 000 3 800 5 000
7312-PJD 60 2.3622 130 5.1181 62 2.4409 2.0 .08 1.0 .040 156 000 35 100 140 000 31 500 3 600 4 800
7313-PJD 65 2.5591 140 5.5118 66 2.5984 2.0 .08 1.0 .040 174 000 39 100 160 000 36 000 3 200 4 300
7314-PJD 70 2.7559 150 5.9055 70 2.7559 2.0 .08 1.0 .040 195 000 43 800 180 000 40 500 3 000 4 000
7315-PJD 75 2.9528 160 6.2992 74 2.9134 2.0 .08 1.0 .040 212 000 47 700 212 000 47 700 2 800 3 800
7316-PJD 80 3.1496 170 6.6929 78 3.0709 2.0 .08 1.0 .040 229 000 51 500 236 000 53 100 2 600 3 600
7317-PJD 85 3.3465 180 7.0866 82 3.2283 2.5 .10 1.0 .040 251 000 56 400 265 000 59 600 2 400 3 400
7318-PJD 90 3.5433 190 7.4803 86 3.3858 2.5 .10 1.0 .040 270 000 60 700 290 000 65 200 2 200 3 200
7319-PJD 95 3.7402 200 7.8740 90 3.5433 2.5 .10 1.0 .040 286 000 64 300 325 000 73 100 2 000 3 000
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
For thrust rating multiply C by 1.75 and C0 by 3.85 (single) and C by 1.08 and C0 by 1.93 (duplex).
3) Listed values are for pressed brass and steel or polyamide cage.
The values have been determined through historical application and practice. For a more complete explanation, see page 274.
4) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
149
7400-PJ Heavy Series and
7400-PJD Heavy Series, Duplex MRC Bearing Services
7400-PJ and -PJD Series bearings are similar to the 7200-
PJ and 7300-PJ Series, but are heavier sectioned; and
are used for very heavy one-directional thrust loads, or
combined radial and thrust loads where the thrust load is
predominant.
“D” indicates a duplex ground half pair matched with an identical half pair and is followed
by an additional suffix letter to describe the type of duplex. See pages 234 nad 235 for
suffix description.
7405-PJ 25 .9843 80 3.1496 21 .8268 1.5 .060 1.0 .040 39 700 8 920 23 600 5 310 7 000 10 000
7406-PJ 30 1.1811 90 3.5433 23 .9055 1.5 .060 1.0 .040 47 500 10 700 29 000 6 520 6 300 9 000
7407-PJ 35 1.3780 100 3.9370 25 .9843 1.5 .060 1.0 .040 60 500 13 600 38 000 8 540 5 600 7 500
7408-PJ 40 1.5748 110 4.3307 27 1.0630 2.0 .080 1.0 .040 70 200 15 800 45 500 10 200 5 300 7 000
7409-PJ 45 1.7717 120 4.7244 29 1.1417 2.0 .080 1.0 .040 85 200 19 200 55 000 12 400 4 800 6 300
7410-PJ 50 1.9685 130 5.1181 31 1.2205 2.0 .080 1.0 .040 95 600 21 500 64 000 14 400 4 300 6 000
7411-PJ 55 2.1654 140 5.5118 33 1.2992 2.0 .080 1.0 .040 111 000 25 000 76 500 17 200 4 000 5 600
7412-PJ 60 2.3622 150 5.9055 35 1.3780 2.0 .080 1.0 .040 119 000 26 800 86 500 19 400 3 600 5 000
7413-PJ 65 2.5591 160 6.2992 37 1.4567 2.0 .080 1.0 .040 130 000 29 200 96 500 21 700 3 400 4 800
7414-PJ 70 2.7559 180 7.0866 42 1.6535 2.5 .100 1.0 .040 159 000 35 700 127 000 28 600 3 000 4 300
7415-PJ 75 2.9528 190 7.4803 45 1.7717 2.5 .100 1.0 .040 168 000 37 800 140 000 31 500 2 800 4 000
7416-PJ 80 3.1496 200 7.8740 48 1.8898 2.5 .100 1.0 .040 178 000 40 000 153 000 34 400 2 600 3 800
7417-PJ 85 3.3465 210 8.2677 52 2.0472 3.0 .120 1.0 .040 190 000 42 700 166 000 37 300 2 500 3 600
7418-PJ 90 3.5433 225 8.8583 54 2.1260 3.0 .120 1.0 .040 216 000 48 600 200 000 45 000 2 400 3 400
7419-PJ 95 3.7402 250 9.8425 55 2.1654 3.0 .120 1.0 .040 251 000 56 400 245 000 55 100 2 200 3 000
7420-PJ 100 3.9370 265 10.4331 60 2.3622 3.0 .120 1.0 .040 276 000 62 000 275 000 61 800 2 000 2 800
7421-PJ 105 4.1339 290 11.4173 65 2.5591 3.0 .120 1.0 .040 265 000 59 600 280 000 62 900 1 900 2 600
7400-PJD
7405-PJD 25 .9843 80 3.1496 42 1.6535 1.5 .060 1.0 .040 65 000 14 500 47 500 10 600 5 600 8 000
7406-PJD 30 1.1811 90 3.5433 46 1.8110 1.5 .060 1.0 .040 78 000 17 400 58 500 13 000 5 000 7 200
7407-PJD 35 1.3780 100 3.9370 50 1.9685 1.5 .060 1.0 .040 97 500 22 100 76 500 17 100 4 500 6 000
7408-PJD 40 1.5748 110 4.3307 54 2.1260 2.0 .080 1.0 .040 114 000 25 700 91 000 20 400 4 300 5 600
7409-PJD 45 1.7717 120 4.7244 58 2.2835 2.0 .080 1.0 .040 138 000 31 200 110 000 24 800 3 800 5 000
7410-PJD 50 1.9685 130 5.1181 62 2.4409 2.0 .080 1.0 .040 156 000 34 900 129 000 28 800 3 400 4 800
7411-PJD 55 2.1654 140 5.5118 66 2.5984 2.0 .080 1.0 .040 182 000 40 600 153 000 34 400 3 200 4 500
7412-PJD 60 2.3622 150 5.9055 70 2.7559 2.0 .080 1.0 .040 195 000 43 600 173 000 38 800 2 800 4 000
7413-PJD 65 2.5591 160 6.2992 74 2.9134 2.0 .080 1.0 .040 212 000 47 400 193 000 43 400 2 700 3 800
7414-PJD 70 2.7559 180 7.0866 84 3.3071 2.5 .100 1.0 .040 260 000 58 000 255 000 57 200 2 400 3 400
7415-PJD 75 2.9528 190 7.4803 90 3.5433 2.5 .100 1.0 .040 276 000 61 400 280 000 63 000 2 200 3 200
7416-PJD 80 3.1496 200 7.8740 96 3.7795 2.5 .100 1.0 .040 288 000 64 800 306 000 68 800 2 000 3 000
7417-PJD 85 3.3465 210 8.2677 104 4.0945 3.0 .120 1.0 .040 307 000 69 400 335 000 74 600 2 000 2 800
7418-PJD 90 3.5433 225 8.8583 108 4.2520 3.0 .120 1.0 .040 351 000 78 900 400 000 89 900 1 900 2 700
7419-PJD 95 3.7402 250 9.8425 110 4.3307 3.0 .120 1.0 .040 410 000 92 200 490 000 110 000 1 800 2 400
7420-PJD 100 3.9370 265 10.4331 120 4.7244 3.0 .120 1.0 .040 449 000 101 000 550 000 124 000 1 600 2 200
7421-PJD 105 4.1339 290 11.4173 130 5.1181 3.0 .120 1.0 .040 436 000 96 900 560 000 126 000 1 500 2 000
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2) For thrust rating multiply C by 1.75 and C0 by 3.85 (single) and C by 1.08 and C0 by 1.93 (duplex).
3) Listed values are for machined bronze cage, ABEC-1.
The values have been determined through historical application and practice. For a more complete explanation, see page 274.
4) Rating for one million revolutions or 500 hours at 33C|z RPM.
150
151
MRC Bearing Services
7000-PJ Series
40° Angular Contact Ball Bearings
Single Bearing
Life rating
3
L10 = (CP) (millions of revolutions)
or
6 3
L10h = 10
60n P
C
()
(Hours)
152
7000-PJ Series
40° Angular Contact Ball Bearings
Single Bearing
Case 1
Radial load (FR) = 1750
Thrust load (FA) = 1960
FA/FR = 1960/1750 = 1.12
Since FA/FR < 1.14, equivalent load (P) = FR = 1750
3 3
Life (L10) = (CP) = (13600
1750 )
= 469 × 106 Rev.
or 6 3 6 3
13600
10 C
() 10
Life (L10h) = 60n P = 60 × 2000 1750 ( )
= 3911 Hrs
Case 2
Radial load (FR) = 1750
Thrust load (FA) = 2450
FA/FR = 2450/1750 = 1.40
Since FA/FR > 1.14, equivalent load (P) = 0.35 FR + 0.57 FA
P = 0.35 × 1750 + 0.57 × 2450 = 2009
3 3
Life (L10) = (CP) = (13600
2009 )
= 310 × 106 Rev.
or 6 3 6 3
13600
10 C
() 10
Life (L10h) = 60n P = 60 × 2000 2009 ( )
= 2585 Hrs
Case 3
Thrust load (FA) = 2450
FA/FR = 2450/0 = ∞
Since FA/FR > 1.14, equivalent load (P) = 0.35 FR + 0.57 FA
P = 0.57 × 2450 = 1397
3 3
Life (L10) = (CP) = (13600
1397 )
= 923 × 106 Rev.
or 6 3 6 3
13600
10 C
() 10
Life (L10h) = 60n P = 60 × 2000 1397 ( )
= 7689 Hrs
153
MRC Bearing Services
7000-PJD Series
40° Angular Contact Ball Bearings
Duplex
FA or
P = 0.57 FR + 0.93 FA when F > 1.14 6 3
R
L10h =
10 C
60n P
() (Hours)
Tandem DT FA
P = 1.0 FR when F ≤ 1.14 P = Dynamic equivalent radial load
R
n = Speed in rpm
FA
P = 0.35 FR + 0.57 FA when F > 1.14 For DB or DF mounting:
R
C = Duplex pair dynamic radial load
P = Dynamic equivalent radial load rating (from duplex bearing tables)
FR = Radial load or
FA = Thrust load C = Single-row dynamic radial load
rating times (i)0.7, where i = 2
For tandem mounting:
C = Single-row dynamic radial load
rating times (i)0.7, where i = number
of bearings in set
154
7000-PJD Series
40° Angular Contact Ball Bearings
Duplex
Series Page
The PumPac 8000 Series is used in centrifugal pumps, The PumPac is furnished with a one piece, inner ring
large vertical electric motors, compressors, centrifuges, land-guided, machined brass cage and is
and other applications subject to thrust loads operating manufactured to meet ABEC-3 grade tolerances.
at relatively high speeds. The bearings are mounted so Dimensional stability is assured by heat treating the
that the 40° (A) bearing takes the primary thrust load. bearing’s rings and rolling elements for operation up to
375˚F (190˚C).
Traditionally, matched sets of 40° angular contact ball
bearings are used to obtain maximum theoretical For identification purposes, the 40° bearing is marked
fatigue life, but in most instances only a fraction of the with the letter “A,” and the 15° bearing with the letter
calculated life is actually achieved. At the heart of these “B”. A “V” is etched on the outer ring surface of the pair
premature failures are phenomena known as “ball so that the apex falls on the “B” bearing. The pair
sliding” and “ball shuttling” in the unloaded (or inactive) should always be mounted so that the “V” points in the
bearing. Angular contact bearings used in high speed same direction as the primary thrust load, which places
(e.g. 3600 RPM) pumps and other applications require this load on bearing “A”. Any reversing load is carried
a minimum axial load for proper operation. Without axial on bearing “B”.
load, gyroscopic forces in the unloaded bearing can
cause the balls to rotate perpendicular to their true The PumPac is also available in the 8000BB PumPac
rolling axis and momentarily lose contact with the Diamond series, which consists of a matched set of
raceway. As a result, a microscopic wear (or lapping) 15° (B) bearings in a back-to-back arrangement.
process occurs giving the appearance of a burnished When mounted correctly, the marking on the outer ring
or polished raceway. The oil film thickness separating surface forms a diamond. This series is desirable in
the ball and raceway is reduced, producing friction and high speed, lightly loaded applications in which axial
heat which lowers oil viscosity and accelerates wear. loads are balanced, resulting in reduced operating
This thermally unstable condition dramatically reduces temperatures and increased life.
bearing service life. For applications involving very heavy primary thrust
The main benefit of the PumPac system is that the 15° loads, the PumPac may be furnished as a triplex set
(B) bearing is designed with considerably less internal identified as the 8000AAB Series. It consists of two 40°
clearance than the 40° (A) bearing, making it less (A) bearings in tandem matched back-to-back (DB)
susceptible to the gyroscopic forces which result in ball with one 15° (B) bearing. The outer ring surface of the
sliding or shuttling. The 15° bearing also provides set is marked with a “V” pointing in the direction of
additional radial stiffness helping to maintain the primary thrust.
integrity of the shaft and mechanical seals. The 40° For applications having a rotating shaft and stationary
(loaded) bearing provides sufficient axial rigidity under housing, an ISO k5 shaft fit and an ISO H6 housing fit
the imposed thrust load. are recommended as shown in the table on page 162.
NOTE: The basic radial load rating, C, is calculated
according to the actual bearing geometry and not
according to ISO/ABMA Standards.
158
PumPac 8000 Series
ABEC 3 Tolerances
Speed
Basic Radial Load Rating 2) Rating3)
MRC Bore Outside Width Fillet Radius1) 40˚ (A) 15˚ (B)
Bearing Diameter Dynamic Static Dynamic Static
Number d D B ra rb C4) C0 C4) C0 Grease Oil
mm in mm in mm in mm in mm in N lbf N lbf N lbf N lbf RPM RPM
8218 90 3.5433 160 6.2992 60 2.3622 2.0 .08 1.0 .04 133 000 29 900 143 000 32 100 124 000 27 900 108 000 24 300 3 400 4 500
8219 95 3.7402 170 6.6929 64 2.5197 2.0 .08 1.0 .04 151 000 33 900 163 000 36 600 133 000 29 900 118 000 26 500 3 200 4 300
8220 100 3.9370 180 7.0866 68 2.6772 2.0 .08 1.0 .04 159 000 35 700 173 000 38 900 146 000 32 800 134 000 30 100 3 000 4 000
8222 110 4.3307 200 7.8740 76 2.9921 2.0 .08 1.0 .04 190 000 42 700 220 000 49 500 182 000 40 900 170 000 38 200 2 600 3 600
8224 120 4.7244 215 8.4646 80 3.1496 2.0 .08 1.0 .04 238 000 53 500 245 000 55 100 199 000 44 700 193 000 43 400 2 200 3 200
8238 190 7.4803 340 13.3858 110 4.3307 3.0 .12 1.0 .04 351 000 78 900 570 000 128 000 377 000 84 800 500 000 112 000 1 400 1 900
8308 40 1.5748 90 3.5433 46 1.8110 1.5 .06 1.0 .04 60 500 13 600 45 500 10 200 48 800 11 000 33 500 7 530 6 700 9 000
8309 45 1.7717 100 3.9370 50 1.9685 1.5 .06 1.0 .04 76 100 17 100 61 000 13 700 58 500 13 200 40 500 9 100 6 000 8 000
8310 50 1.9685 110 4.3307 54 2.1260 2.0 .08 1.0 .04 87 100 19 600 72 000 16 200 76 100 17 100 52 000 11 700 5 300 7 000
8311 55 2.1654 120 4.7244 58 2.2835 2.0 .08 1.0 .04 101 000 22 700 85 000 19 100 88 400 19 900 61 000 13 700 4 800 6 300
8312 60 2.3622 130 5.1181 62 2.4409 2.0 .08 1.0 .04 114 000 25 600 96 500 21 700 101 000 22 700 71 000 16 000 4 500 6 000
8313 65 2.5591 140 5.5118 66 2.5984 2.0 .08 1.0 .04 127 000 28 500 112 000 25 200 108 000 24 300 80 000 18 000 4 300 5 600
8314 70 2.7559 150 5.9055 70 2.7559 2.0 .08 1.0 .04 148 000 33 300 134 000 31 500 121 000 27 200 93 000 20 900 3 800 5 000
8315 75 2.9528 160 6.2992 74 2.9134 2.0 .08 1.0 .04 159 000 35 700 150 000 33 700 146 000 32 800 114 000 25 600 3 600 4 800
8316 80 3.1496 170 6.6929 78 3.0709 2.0 .08 1.0 .04 172 000 38 700 166 000 37 300 159 000 35 700 129 000 29 200 3 400 4 500
8317 85 3.3465 180 7.0866 82 3.2283 2.5 .10 1.0 .04 186 000 41 800 186 000 41 800 174 000 39 100 146 000 32 800 3 200 4 300
8318 90 3.5433 190 7.4803 86 3.3858 2.5 .10 1.0 .04 199 000 44 700 204 000 45 900 186 000 41 800 160 000 36 000 3 000 4 000
8319 95 3.7402 200 7.8740 90 3.5433 2.5 .10 1.0 .04 212 000 47 600 228 000 51 300 199 000 44 700 180 000 40 500 2 800 3 800
8320 100 3.9370 215 8.4646 94 3.7008 2.5 .10 1.0 .04 238 000 53 500 270 000 60 700 212 000 47 700 200 000 45 000 2 600 3 600
8322 110 4.3307 240 9.4488 100 3.9370 2.5 .10 1.0 .04 265 000 59 600 320 000 71 900 255 000 57 300 255 000 57 300 2 200 3 200
8326 130 5.1181 280 11.0236 116 4.5669 3.0 .12 1.0 .04 345 000 77 500 455 000 102 000 296 000 66 500 345 000 77 600 1 800 2 600
8330 150 5.9055 320 12.5984 130 5.1181 3.0 .12 1.0 .04 410 000 92 100 585 000 132 000 390 000 87 700 475 000 107 000 1 600 2 200
8336 180 7.0866 380 14.9606 150 5.9055 3.0 .12 1.0 .04 507 000 114 000 815 000 183 000 475 000 107 000 640 000 144 000 1 300 1 600
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
For thrust rating of bearing (A), multiply C by 1.75 and Co by 3.85.
For thrust rating of bearing (B), multiply C by 0.83 and Co by 2.00.
3)
Values have been determined through historical application and practice. For a more complete explanation, see page 274.
4) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
159
PumPac Diamond
8000-BB Series MRC Bearing Services
ABEC 3 Tolerances
8218BB 90 3.5433 160 6.2992 60 2.3622 2.0 .08 1.0 .04 203 000 45 600 216 000 48 600 3 800 5 400
8219BB 95 3.7402 170 6.6929 64 2.5197 2.0 .08 1.0 .04 216 000 48 600 236 000 53 100 3 600 5 100
8220BB 100 3.9370 180 7.0866 68 2.6772 2.0 .08 1.0 .04 238 000 53 500 270 000 60 700 3 400 4 800
8222BB 110 4.3307 200 7.8740 76 2.9921 2.0 .08 1.0 .04 296 000 66 500 340 000 76 400 3 000 4 400
8224BB 120 4.7244 215 8.4646 80 3.1496 2.0 .08 1.0 .04 319 000 71 800 390 000 87 700 2 800 4 100
8238BB 190 7.4803 340 13.3858 110 4.3307 3.0 .12 1.0 .04 605 000 136 000 1 000 000 225 000 1 800 2 600
8308BB 40 1.5748 90 3.5433 46 1.8110 1.5 .06 1.0 .04 79 300 17 800 67 000 15 100 7 500 11 000
8309BB 45 1.7717 100 3.9370 50 1.9685 1.5 .06 1.0 .04 95 600 21 500 81 500 18 300 6 800 9 600
8310BB 50 1.9685 110 4.3307 54 2.1260 2.0 .08 1.0 .04 124 000 27 900 104 000 23 400 6 300 9 000
8311BB 55 2.1654 120 4.7244 58 2.2835 2.0 .08 1.0 .04 143 000 32 100 122 000 27 400 5 600 8 100
8312BB 60 2.3622 130 5.1181 62 2.4409 2.0 .08 1.0 .04 165 000 37 100 143 000 32 100 5 000 7 200
8313BB 65 2.5591 140 5.5118 66 2.5984 2.0 .08 1.0 .04 174 000 39 100 160 000 36 000 4 800 6 800
8314BB 70 2.7559 150 5.9055 70 2.7559 2.0 .08 1.0 .04 199 000 44 700 190 000 42 700 4 500 6 300
8315BB 75 2.9528 160 6.2992 74 2.9134 2.0 .08 1.0 .04 238 000 53 500 228 000 51 300 4 300 6 000
8316BB 80 3.1496 170 6.6929 78 3.0709 2.0 .08 1.0 .04 255 000 57 300 260 000 58 500 3 800 5 400
8317BB 85 3.3465 180 7.0866 82 3.2283 2.5 .10 1.0 .04 281 000 63 200 292 000 65 600 3 600 5 100
8318BB 90 3.5433 190 7.4803 86 3.3858 2.5 .10 1.0 .04 302 000 67 900 325 000 73 100 3 400 4 800
8319BB 95 3.7402 200 7.8740 90 3.5433 2.5 .10 1.0 .04 325 000 73 100 360 000 80 900 3 300 4 500
8320BB 100 3.9370 215 8.4646 94 3.7008 2.5 .10 1.0 .04 345 000 77 600 400 000 89 900 3 000 4 400
8322BB 110 4.3307 240 9.4488 100 3.9370 2.5 .10 1.0 .04 416 000 93 500 510 000 115 000 2 600 3 900
8326BB 130 5.1181 280 11.0236 116 4.5669 3.0 .12 1.0 .04 475 000 107 000 695 000 156 000 2 300 3 300
8330BB 150 5.9055 320 12.5984 130 5.1181 3.0 .12 1.0 .04 624 000 140 000 950 000 214 000 2 000 2 900
8336BB 180 7.0866 380 14.9606 150 5.9055 3.0 .12 1.0 .04 780 000 175 000 1 270 000 286 000 1 600 2 400
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
For thrust rating multiply C by 0.51 and Co by 1.00.
3) Values have been determined through historical application and practice. For a more complete explanation, see page 274.
4) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
160
PumPac 8000-AAB Series
ABEC 3 Tolerances
8218AAB 90 3.5433 160 6.2992 90 3.5433 2.0 .08 1.0 .04 216 000 48 500 285 000 64 100 124 000 27 900 108 000 24 300 3 400 4 500
8219AAB 95 3.7402 170 6.6929 96 3.7795 2.0 .08 1.0 .04 247 000 55 500 325 000 73 100 133 000 29 900 118 000 26 500 3 200 4 300
8220AAB 100 3.9370 180 7.0866 102 4.0157 2.0 .08 1.0 .04 260 000 58 400 345 000 78 700 146 000 32 800 134 000 30 100 3 000 4 000
8222AAB 110 4.3307 200 7.8740 114 4.4882 2.0 .08 1.0 .04 307 000 69 000 440 000 98 900 182 000 40 900 170 000 38 200 2 600 3 600
8224AAB 120 4.7244 215 8.4646 120 4.7244 2.0 .08 1.0 .04 390 000 87 600 490 000 110 000 199 000 44 700 193 000 43 400 2 200 3 200
8238AAB 190 7.4803 340 13.3858 165 6.4961 3.0 .12 1.0 .04 572 000 129 000 1140 000 256 000 377 000 84 800 500 000 112 000 1 400 1 900
8308AAB 40 1.5748 90 3.5433 69 2.7165 1.5 .06 1.0 .04 97 500 21 900 91 500 20 600 48 800 11 000 33 500 7 530 6 700 9 000
8309AAB 45 1.7717 100 3.9370 75 2.9528 1.5 .06 1.0 .04 124 000 27 900 122 000 27 400 58 500 13 200 40 500 9 100 6 000 8 000
8310AAB 50 1.9685 110 4.3307 81 3.1890 2.0 .08 1.0 .04 143 000 32 100 143 000 32 100 76 100 17 100 52 000 11 700 5 300 7 000
8311AAB 55 2.1654 120 4.7244 87 3.4252 2.0 .08 1.0 .04 165 000 37 100 170 000 38 200 88 400 19 900 61 000 13 700 4 800 6 300
8312AAB 60 2.3622 130 5.1181 93 3.6614 2.0 .08 1.0 .04 186 000 41 800 193 000 43 400 101 000 22 700 71 000 16 000 4 500 6 000
8313AAB 65 2.5591 140 5.5118 99 3.8976 2.0 .08 1.0 .04 208 000 46 700 224 000 50 400 108 000 24 300 80 000 18 000 4 300 5 600
8314AAB 70 2.7559 150 5.9055 105 4.1339 2.0 .08 1.0 .04 242 000 54 400 270 000 60 700 121 000 27 200 93 000 20 900 3 800 5 000
8315AAB 75 2.9528 160 6.2992 111 4.3701 2.0 .08 1.0 .04 260 000 58 400 300 000 67 400 146 000 32 800 114 000 25 600 3 600 4 800
8316AAB 80 3.1496 170 6.6929 117 4.6063 2.0 .08 1.0 .04 281 000 63 100 335 000 75 300 159 000 35 700 129 000 29 200 3 400 4 500
8317AAB 85 3.3465 180 7.0866 123 4.8425 2.5 .10 1.0 .04 302 000 67 900 375 000 84 300 174 000 39 100 146 000 32 800 3 200 4 300
8318AAB 90 3.5433 190 7.4803 129 5.0787 2.5 .10 1.0 .04 325 000 73 000 405 000 91 000 186 000 41 800 160 000 36 000 3 000 4 000
8319AAB 95 3.7402 200 7.8740 135 5.3150 2.5 .10 1.0 .04 345 000 77 500 455 000 102 000 199 000 44 700 180 000 40 500 2 800 3 800
8320AAB 100 3.9370 215 8.4646 141 5.5512 2.5 .10 1.0 .04 390 000 87 600 540 000 121 000 212 000 47 700 200 000 45 000 2 600 3 600
8322AAB 110 4.3307 240 9.4488 150 5.9055 2.5 .10 1.0 .04 436 000 98 000 640 000 144 000 255 000 57 300 255 000 57 300 2 200 3 200
8326AAB 130 5.1181 280 11.0236 174 6.8504 3.0 .12 1.0 .04 559 000 126 000 915 000 206 000 296 000 66 500 345 000 77 600 1 800 2 600
8330AAB 150 5.9055 320 12.5984 195 7.6772 3.0 .12 1.0 .04 663 000 149 000 1180 000 265 000 390 000 87 700 475 000 107 000 1 600 2 200
8336AAB 180 7.0866 380 14.9606 225 8.8583 3.0 .12 1.0 .04 824 000 185 000 1630 000 366 000 475 000 107 000 640 000 144 000 1 300 1 600
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2) For thrust rating of (AA) multiply C by 1.75 and Co by 3.85. For thrust rating of (B) multiply C by 0.83 and Co by 2.00.
3)
Values have been determined through historical application and practice. For a more complete explanation, see page 274.
4) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
161
PumPac
Shaft and Housing Fits MRC Bearing Services
8222 110.018 4.3314 110.003 4,3308 3T-33T 1T-13T 200.029 7.8751 200.000 7.8740 0-49L 0-19L
8224 120.018 4.7251 120.003 4.7245 3T-33T 1T-13T 215.029 8.4657 215.000 8.4646 0-49L 0-19L
8238 190.024 7.4812 190.004 7.4805 4T-46T 2T-18T 340.036 13.3872 340.000 13.3858 0-64L 0-25L
8308 40.013 1.5753 40.002 1.5749 2T-23T 1T-9T 90.022 3.5442 90.000 3.5433 0-35L 0-14L
8309 45.013 1.7722 45.002 1.7718 2T-23T 1T-9T 100.022 3.9379 100.000 3.9370 0-35L 0-14L
8310 50.013 1.9690 50.002 1.9686 2T-23T 1T-9T 110.022 4.3316 110.000 4.3307 0-35L 0-14L
8311 55.015 2.1660 55.002 2.1655 2T-27T 1T-11T 120.022 4.7253 120.000 4.7244 0-35L 0-14L
8312 60.015 2.3628 60.002 2.3623 2T-27T 1T-11T 130.025 5.1191 130.000 5.1181 0-40L 0-16L
8313 65.015 2.5597 65.002 2.5592 2T-27T 1T-11T 140.025 5.5128 140.000 5.5118 0-40L 0-16L
8314 70.015 2.7565 70.002 2.7560 2T-27T 1T-11T 150.025 5.9065 150.000 5.9055 0-40L 0-16L
8315 75.015 2.9534 75.002 2.9529 2T-27T 1T-11T 160.025 6.3002 160.000 6.2992 0-43L 0-17L
8316 80.015 3.1502 80.002 3.1497 2T-27T 1T-11T 170.025 6.6939 170.000 6.6929 0-43L 0-17L
8317 85.018 3.3472 85.003 3.3466 3T-33T 1T-13T 180.025 7.0876 180.000 7.0866 0-43L 0-17L
8318 90.018 3.5440 90.003 3.5434 3T-33T 1T-13T 190.029 7.4814 190.000 7.4803 0-49L 0-19L
8319 95.018 3.7409 95.003 3.7403 3T-33T 1T-13T 200.029 7.8751 200.000 7.8740 0-49L 0-19L
8320 100.018 3.9377 100.003 3.9371 3T-33T 1T-13T 215.029 8.4657 215.000 8.4646 0-49L 0-19L
8322 110.018 4.3314 110.003 4.3308 3T-33T 1T-13T 240.029 9.4499 240.000 9.4488 0-49L 0-19L
8326 130.021 5.1189 130.003 5.1182 3T-39T 1T-15T 280.032 11.0249 280.000 11.0236 0-57L 0-23L
8330 150.021 5.9063 150.003 5.9056 3T-39T 1T-15T 320.036 12.5998 320.000 12.5984 0-64L 0-25L
8336 180.021 7.0874 180.003 7.0867 3T-39T 1T-15T 380.036 14.9620 380.000 14.9606 0-64L 0-25L
1) Cast iron or steel housings. For aluminum or other soft metal housings make housing bore limits same as bearing O.D. limits
2)
“T” indicates tight, “L” indicates loose
162
PumPac
Mounting Instructions
8000 8000AAB
163
PumPac Dynamic and Static Equivalent
Radial Load and Life Rating MRC Bearing Services
The following method considers only thrust load in either direction with negligible radial load. For combined radial
and thrust loads consult MRC Technical Services for analysis.
Dynamic equivalent radial load Static equivalent radial load
Primary thrust on bearing A (40˚) Bearing A (40˚)
P = 0.57 FA P0 = 0.26 FA
Reversing thrust on bearing B (15˚) Bearing B (15˚)
P = YFA P0 = 0.5 FA
P = Dynamic equivalent radial load P0 = Static equivalent radial load
FA = Thrust load FA = Thrust load
Y = Thrust load factor
Z = Number of balls
D = Ball diameter
FA
ZD2 Y
N,mm Lb,in.
0.172 25 1.47
0.345 50 1.40
0.689 100 1.30
1.03 150 1.23
FA
1.38 200 1.19
ZD2
2.07 300 1.12 (N, mm)
3.45 500 1.02
5.17 750 1.00
6.89 1 000 1.00
ZD 2 ZD 2 ZD 2
Size Size Size
mm inch mm inch mm inch
8218B 7410 11.5 8310B 3990 6.19 8318B 11800 18.3
8219B 7900 12.3 8311B 4690 7.26 8319B 13100 20.3
8220B 9070 14.1 8312B 5430 8.42 8320B 14400 22.4
8222B 11700 18.1 8313B 5930 9.19 8322B 18900 29.3
8224B 13100 20.3 8314B 6800 10.5 8326B 25700 39.8
Values of Y for loads not shown are obtained from chart at right.
164
Dynamic equivalent radial load
and life calculation examples
165
166
9000 Series Single-Row 29° and 40°
Split Ring Angular Contact Ball Bearings
Demand for a two-directional maximum thrust capacity 9000-H has a two-piece outer ring and a one-piece inner
bearing requiring minimum space has resulted in ring. Recommended only where the outer ring
extensive use of the MRC 9000 Series bearings. can be positively clamped. When duplexed, bearing
167
9100-UK and 9200-U Series
Split Inner Ring Angular Contact Ball Bearings MRC Bearing Services
For duplex sets of 7000 and 9000 series bearings see page 237.
9100-UK 10 .3937 26 1.0236 8 .3150 .30 .012 4 620 1 040 2 080 468 30 000 39 000
9101-UK 12 .4724 28 1.1024 8 .3150 .30 .012 5 070 1 140 2 500 562 25 000 32 000
9102-UK 15 .5906 32 1.2598 9 .3543 .30 .012 5 400 1 210 2 900 652 22 000 28 000
9103-UK 17 .6693 35 1.3780 10 .3937 .30 .012 7 610 1 710 4 250 955 19 000 25 000
9104-UK 20 .7874 42 1.6535 12 .4724 .64 .025 9 560 2 150 5 600 1 260 16 000 21 000
9105-UK 25 .9843 47 1.8504 12 .4724 .64 .025 10 600 2 380 6 950 1 560 12 000 16 000
9106-UK 30 1.1811 55 2.1654 13 .5118 1.0 .04 13 800 3 100 9 650 2 170 11 000 14 000
9107-UK 35 1.3780 62 2.4409 14 .5512 1.0 .04 16 800 3 780 12 000 2 700 9 200 12 000
9108-UK 40 1.5748 68 2.6772 15 .5906 1.0 .04 17 200 3 870 13 200 2 970 8 500 11 000
9109-UK 45 1.7717 75 2.9528 16 .6299 1.0 .04 21 200 4 770 17 000 3 820 7 500 9 800
9110-UK 50 1.9685 80 3.1496 16 .6299 1.0 .04 22 100 4 970 18 300 4 110 6 900 9 000
9111-UK 55 2.1654 90 3.5433 18 .7087 1.0 .04 29 600 6 650 25 500 5 730 6 300 8 200
9112-UK 60 2.3622 95 3.7402 18 .7087 1.0 .04 30 200 6 790 27 000 6 070 5 700 7 400
9113-UK 65 2.5591 100 3.9370 18 .7087 1.0 .04 31 200 7 010 29 000 6 520 5 400 7 000
9114-UK 70 2.7559 110 4.3307 20 .7874 1.0 .04 34 500 7 760 35 500 7 980 5 000 6 500
9115-UK 75 2.9528 115 4.5276 20 .7874 1.0 .04 37 700 8 480 37 500 8 430 4 700 6 100
9116-UK 80 3.1496 125 4.9213 22 .8661 1.0 .04 48 800 11 000 49 000 11 000 4 500 5 800
9117-UK 85 3.3465 130 5.1181 22 .8661 1.0 .04 49 400 11 100 52 000 11 700 4 100 5 300
9118-UK 90 3.5433 140 5.5118 24 .9449 1.5 .06 58 500 13 200 61 000 13 700 3 800 4 900
9119-UK 95 3.7402 145 5.7087 24 .9449 1.5 .06 71 500 16 100 71 000 16 000 3 600 4 700
9120-UK 100 3.9370 150 5.9055 24 .9449 1.5 .06 62 400 14 000 68 000 15 300 3 500 4 500
9121-UK 105 4.1339 160 6.2992 26 1.0236 2.0 .08 74 100 16 700 80 000 18 000 3 300 4 300
9122-UK 110 4.3307 170 6.6929 28 1.1024 2.0 .08 87 100 19 600 91 500 20 600 3 200 3 800
9200-U
9202-U 15 .5906 35 1.3780 11 .4331 .64 .025 8 060 1 810 4 750 1 070 20 000 26 000
9203-U 17 .6693 40 1.5748 12 .4724 .64 .025 9 950 2 240 6 100 1 370 18 000 23 000
9204-U 20 .7874 47 1.8504 14 .5512 1.0 .04 11 900 2 680 7 100 1 600 15 000 19 000
9205-U 25 .9843 52 2.0472 15 .5906 1.0 .04 14 300 3 210 8 800 1 980 12 000 16 000
9206-U 30 1.1811 62 2.4409 16 .6299 1.0 .04 16 800 3 780 11 800 2 650 10 000 13 000
9207-U 35 1.3780 72 2.8346 17 .6693 1.0 .04 23 400 5 260 17 000 3 820 9 200 12 000
9208-U 40 1.5748 80 3.1496 18 .7087 1.0 .04 30 700 6 900 22 800 5 130 7 700 10 000
9209-U 45 1.7717 85 3.3465 19 .7480 1.0 .04 31 900 7 170 25 000 5 620 7 300 9 500
9210-U 50 1.9685 90 3.5433 20 .7874 1.0 .04 33 200 7 460 27 000 6 070 6 400 8 300
9211-U 55 2.1654 100 3.9370 21 .8268 1.5 .06 48 800 11 000 37 500 8 430 6 000 7 800
9212-U 60 2.3622 110 4.3307 22 .8661 1.5 .06 52 700 11 800 44 000 9 890 5 400 7 000
9213-U 65 2.5591 120 4.7244 23 .9055 1.5 .06 63 700 14 300 54 000 12 100 4 900 6 400
9214-U 70 2.7559 125 4.9213 24 .9449 1.5 .06 63 700 14 300 55 000 12 400 4 600 6 000
9215-U 75 2.9528 130 5.1181 25 .9843 1.5 .06 76 100 17 100 65 500 14 700 4 300 5 600
9216-U 80 3.1496 140 5.5118 26 1.0236 2.0 .08 78 000 17 500 71 000 16 000 4 100 5 300
9217-U 85 3.3465 150 5.9055 28 1.1024 2.0 .08 90 400 20 300 85 000 19 100 3 800 4 900
9218-U 90 3.5433 160 6.2992 30 1.1811 2.0 .08 112 000 25 100 98 000 22 000 3 600 4 700
9219-U 95 3.7402 170 6.6929 32 1.2598 2.0 .08 117 000 26 300 108 000 24 300 3 500 4 500
9220-U 100 3.9370 180 7.0866 34 1.3386 2.0 .08 130 000 29 200 122 000 27 400 3 200 4 100
9221-U 105 4.1339 190 7.4803 36 1.4173 2.0 .08 148 000 33 300 137 000 30 800 3 000 3 900
9222-U 110 4.3307 200 7.8740 38 1.4961 2.0 .08 163 000 36 600 156 000 35 100 2 900 3 800
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear. 2) For thrust rating multiply C by 1.32 and C by 2.94.
0
3)
Listed values are for machined bronze cage, ABEC-1. The values have been determined through historical application and practice. For a more complete explanation, see page 274.
4) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
168
9300-U Series
Split Inner Ring Angular Contact Ball Bearings
For duplex sets of 7000 and 9000 series bearings see page 237.
9302-U 15 .5906 42 1.6535 13 .5118 1.0 .04 9 950 2 240 6 100 1 370 16 000 21 000
9303-U 17 .6693 47 1.8504 14 .5512 1.0 .04 12 100 2 720 7 500 1 690 15 000 19 000
9304-U 20 .7874 52 2.0472 15 .5906 1.0 .04 18 600 4 180 10 600 2 380 13 000 17 000
9305-U 25 .9843 62 2.4409 17 .6693 1.0 .04 21 200 4 770 13 700 3 080 11 000 14 000
9306-U 30 1.1811 72 2.8346 19 .7480 1.0 .04 28 100 6 320 18 600 4 180 9 200 12 000
9307-U 35 1.3780 80 3.1496 21 .8268 1.5 .06 35 800 8 050 24 000 5 400 8 500 11 000
9308-U 40 1.5748 90 3.5433 23 .9055 1.5 .06 44 200 9 940 31 000 7 000 7 300 9 500
9309-U 45 1.7717 100 3.9370 25 .9843 1.5 .06 52 700 11 800 38 000 8 540 6 400 8 300
9310-U 50 1.9685 110 4.3307 27 1.0630 2.0 .08 68 900 15 500 49 000 11 000 5 800 7 500
9311-U 55 2.1654 120 4.7244 29 1.1417 2.0 .08 80 600 18 100 57 000 12 800 5 100 6 600
9312-U 60 2.3622 130 5.1181 31 1.2205 2.0 .08 92 300 20 700 65 500 14 700 4 900 6 400
9313-U 65 2.5591 140 5.5118 33 1.2992 2.0 .08 97 500 21 900 75 000 16 900 4 600 6 000
9314-U 70 2.7559 150 5.9055 35 1.3780 2.0 .08 111 000 25 000 85 000 19 100 4 100 5 300
9315-U 75 2.9528 160 6.2992 37 1.4567 2.0 .08 130 000 29 200 106 000 23 800 3 900 5 000
9316-U 80 3.1496 170 6.6929 39 1.5354 2.0 .08 143 000 32 100 120 000 27 000 3 600 4 700
9317-U 85 3.3465 180 7.0866 41 1.6142 2.5 .10 153 000 34 400 134 000 30 100 3 500 4 500
9318-U 90 3.5433 190 7.4803 43 1.6929 2.5 .10 168 000 37 800 150 000 33 700 3 200 4 200
9319-U 95 3.7402 200 7.8740 45 1.7717 2.5 .10 178 000 40 000 166 000 37 300 3 100 4 000
9320-U 100 3.9370 215 8.4646 47 1.8504 2.5 .10 190 000 42 700 183 000 41 100 3 000 3 900
9321-U 105 4.1339 225 8.8583 49 1.9291 2.5 .10 203 000 45 600 200 000 45 000 2 900 3 800
9322-U 110 4.3307 240 9.4488 50 1.9685 2.5 .10 229 000 51 500 236 000 53 100 2 700 3 500
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2) For thrust rating multiply C by 1.32 and C0 by 2.94.
3) Listed values are for machined bronze cage, ABEC-1.
The values have been determined through historical application and practice. For a more complete explanation, see page 274.f
4) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
169
170
9200-UP and 9300-UP Series
Split Inner Ring Angular Contact Ball Bearings
For duplex sets of 7000 and 9000 series bearings see page 237.
9202-UP 15 .5906 35 1.3780 11 .4331 .64 .025 8 840 1 990 4 250 955 17 000 24 000
9203-UP 17 .6693 40 1.5748 12 .4724 .64 .025 11 700 2 630 6 000 1 350 15 000 20 000
9204-UP 20 .7874 47 1.8504 14 .5512 1.0 .04 14 800 3 330 8 300 1 870 12 000 17 000
9205-UP 25 .9843 52 2.0472 15 .5906 1.0 .04 16 800 3 780 10 400 2 340 10 000 15 000
9206-UP 30 1.1811 62 2.4409 16 .6299 1.0 .04 21 200 4 770 12 700 2 860 8 500 12 000
9207-UP 35 1.3780 72 2.8346 17 .6693 1.0 .04 29 100 6 540 19 300 4 340 8 000 11 000
9208-UP 40 1.5748 80 3.1496 18 .7087 1.0 .04 32 500 7 310 22 400 5 040 7 000 9 500
9209-UP 45 1.7717 85 3.3465 19 .7480 1.0 .04 39 000 8 770 27 500 6 180 6 700 9 000
9210-UP 50 1.9685 90 3.5433 20 .7874 1.0 .04 40 300 9 060 30 000 6 740 6 000 8 000
9211-UP 55 2.1654 100 3.9370 21 .8268 1.5 .06 48 800 11 000 37 500 8 430 5 600 7 500
9212-UP 60 2.3622 110 4.3307 22 .8661 1.5 .06 58 500 13 200 45 500 10 200 5 000 6 700
9213-UP 65 2.5591 120 4.7244 23 .9055 1.5 .06 63 700 14 300 51 000 11 500 4 500 6 000
9214-UP 70 2.7559 125 4.9213 24 .9449 1.5 .06 68 900 15 500 56 000 12 600 4 300 5 600
9215-UP 75 2.9528 130 5.1181 25 .9843 1.5 .06 71 500 16 100 60 000 13 500 4 000 5 300
9216-UP 80 3.1496 140 5.5118 26 1.0236 2.0 .08 83 200 18 700 71 000 16 000 3 800 5 000
9217-UP 85 3.3465 150 5.9055 28 1.1024 2.0 .08 95 600 21 500 83 000 18 700 3 600 4 800
9218-UP 90 3.5433 160 6.2992 30 1.1811 2.0 .08 108 000 24 300 95 000 21 400 3 400 4 500
9219-UP 95 3.7402 170 6.6929 32 1.2598 2.0 .08 124 000 27 900 110 000 24 700 3 200 4 300
9220-UP 100 3.9370 180 7.0866 34 1.3386 2.0 .08 130 000 29 200 125 000 28 100 3 000 4 000
9221-UP 105 4.1339 190 7.4803 36 1.4173 2.0 .08 143 000 32 100 129 000 29 000 2 800 3 800
9222-UP 110 4.3307 200 7.8740 38 1.4961 2.0 .08 153 000 34 400 156 000 35 100 2 600 3 600
9300-UP
9302-UP 15 .5906 42 1.6535 13 .5118 1.0 .04 12 700 2 860 6 100 1 370 15 000 20 000
9303-UP 17 .6693 47 1.8504 14 .5512 1.0 .04 16 800 3 780 8 500 1 910 13 000 18 000
9304-UP 20 .7874 52 2.0472 15 .5906 1.0 .04 18 600 4 180 9 500 2 140 11 000 16 000
9305-UP 25 .9843 62 2.4409 17 .6693 1.0 .04 24 200 5 440 13 400 3 010 9 000 13 000
9306-UP 30 1.1811 72 2.8346 19 .7480 1.0 .04 32 500 7 310 19 600 4 410 8 000 11 000
9307-UP 35 1.3780 80 3.1496 21 .8268 1.5 .06 39 700 8 920 24 500 5 510 7 500 10 000
9308-UP 40 1.5748 90 3.5433 23 .9055 1.5 .06 47 500 10 700 30 500 6 860 6 700 9 000
9309-UP 45 1.7717 100 3.9370 25 .9843 1.5 .06 59 200 13 300 40 000 8 990 6 000 8 000
9310-UP 50 1.9685 110 4.3307 27 1.0630 2.0 .08 68 900 15 500 52 000 11 700 5 300 7 000
9311-UP 55 2.1654 120 4.7244 29 1.1417 2.0 .08 79 300 17 800 56 000 12 600 4 800 6 300
9312-UP 60 2.3622 130 5.1181 31 1.2205 2.0 .08 90 400 20 300 64 000 14 400 4 500 6 000
9313-UP 65 2.5591 140 5.5118 33 1.2992 2.0 .08 101 000 22 700 80 000 18 000 4 300 5 600
9314-UP 70 2.7559 150 5.9055 35 1.3780 2.0 .08 117 000 26 300 93 000 20 900 3 800 5 000
9315-UP 75 2.9528 160 6.2992 37 1.4567 2.0 .08 127 000 28 600 100 000 22 500 3 600 4 800
9316-UP 80 3.1496 170 6.6929 39 1.5354 2.0 .08 138 000 31 000 110 000 24 700 3 400 4 500
9317-UP 85 3.3465 180 7.0866 41 1.6142 2.5 .10 148 000 33 300 122 000 27 400 3 200 4 300
9318-UP 90 3.5433 190 7.4803 43 1.6929 2.5 .10 159 000 35 700 137 000 30 800 3 000 4 000
9319-UP 95 3.7402 200 7.8740 45 1.7717 2.5 .10 168 000 37 800 150 000 33 700 2 800 3 800
9320-UP 100 3.9370 215 8.4646 47 1.8504 2.5 .10 190 000 42 700 190 000 42 700 2 600 3 600
9321-UP 105 4.1339 225 8.8583 49 1.9291 2.5 .10 203 000 45 600 196 000 44 100 2 400 3 400
9322-UP 110 4.3307 240 9.4488 50 1.9685 2.5 .10 212 000 47 700 228 000 51 300 2 200 3 200
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
For thrust rating multiply C by 1.75 and C0 by 3.85.
3) Listed values are for machined bronze cage, ABEC-1.
The values have been determined through historical application and practice. For a more complete explanation, see page 274.
4) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
171
MRC Bearing Services
9000-U Series
Split Inner Ring
29° Angular Contact Ball Bearings
Single Bearing
Life rating
3
L10 =
or
C
P ()(millions of revolutions)
Minimum Thrust Load A Factor
6 3
L10h = 10 C
60n P
()
(Hours) Size
9100UK
A
0.06
Size
9202U
A
0.19
Size
9202UP
A
0.42
C = Basic dynamic radial load rating 9101UK 0.08 9203U 0.30 9203UP 0.74
9102UK 0.11 9204U 0.42 9204UP 1.32
(from single bearing tables) 9103UK 0.20 9205U 0.94 9205UP 1.90
P = Dynamic equivalent radial load 9104UK 0.37 9206U 1.41 9206UP 3.45
9105UK 0.52 9207U 2.82 9207UP 6.73
n = Speed in rpm 9106UK 0.95 9208U 4.95 9208UP 9.28
9107UK 1.50 9209U 5.46 9209UP 13.13
172
9000-U Series
Split Inner Ring
29° Angular Contact Ball Bearings
Single Bearing
Case 1
Radial load (FR) = 1750
Thrust load (FA) = 1310
Equivalent load (P) = FR or 0.39 FR + 0.76 FA
FA/FR = 1310/1750 = 0.75
Since FA/FR < 0.80, P = FR = 1750
3 3
Life (L10) = (CP) = (11800
1750 )
= 307 × 106 Rev.
or 6 3 6 3
11800
10 C
() 10
Life (L10h) = 60n P = 60 × 2000 1750 ( )
= 2555 Hrs
Case 2
Radial load (FR) = 1750
Thrust load (FA) = 2100
Equivalent load (P) = FR or 0.39 FR + 0.76 FA
FA/FR = 2100/1750 = 1.20
Since FA/FR > 0.80, P = 0.39 × 1750 + 0.76 × 2100 = 2279
3 3
Life (L10) = (CP) = (11800
2279 )
= 139 × 106 Rev.
or 6 3 6 3
11800
10 C
() 10
Life (L10h) = 60n P = 60 × 2000 2279 ( )
= 1157 Hrs
Case 3
Thrust load (FA) = 2100
Equivalent load (P) = 0.39 FR + 0.76 FA
FA/FR = 2100/0 = ∞
Since FA/FR > 0.80, P = 0.76 × 2100 = 1596
3 3
Life (L10) = (CP) = (11800
1596 )
= 404 × 106 Rev.
or 6 3 6 3
11800
10 C
() 10
Life (L10h) = 60n P = 60 × 2000 1596 ( )
= 3368 Hrs
173
MRC Bearing Services
9000-UP Series
Split Inner Ring
40° Angular Contact Ball Bearings
Single Bearing
Life rating
3
L10 = (CP) (millions of revolutions)
or
6 3
L10h =
10 C
60n P
() (Hours)
174
9000-UP Series
Split Inner Ring
40˚ Angular Contact Ball Bearings
Single Bearing
Case 1
Radial load (FR) = 1750
Thrust load (FA) = 1960
FA/FR = 1960/1750 = 1.12
Since FA/FR < 1.14, equivalent load (P) = FR = 1750
3 3
Life (L10) = (CP) = (13300
1750 )
= 439 × 106 Rev.
or 6 3 6 3
13300
10 C
() 10
Life (L10h) = 60n P = 60 × 2000 1750 ( )
= 3658 Hrs
Case 2
Radial load (FR) = 1750
Thrust load (FA) = 2450
FA/FR = 2450/1750 = 1.40
Since FA/FR > 1.14, equivalent load (P) = 0.35 FR + 0.57 FA
P = 0.35 × 1750 + 0.57 × 2450 = 2009
3 3
13300
Life (L10) = () (
C
P
=
2009 ) = 290 × 106 Rev.
or 6 3 6 3
13300
10 C
() 10
Life (L10h) = 60n P = 60 × 2000 2009 ( )
= 2418 Hrs
Case 3
Thrust load (FA) = 2450
FA/FR = 2450/0 = ∞
Since FA/FR > 1.14, equivalent load (P) = 0.35 FR + 0.57 FA
P = 0.57 × 2450 = 1397
3 3
Life (L10) = (CP) = (13300
1397 )
= 863 × 106 Rev.
or 6 3 6 3
13300
10 C
() 10
Life (L10h) = 60n P = 60 × 2000 1397 ( )
= 7191 Hrs
175
176
97000 U2 and 97000 UP2 Series
Angular Contact Ball Bearings
The 97000U Series consists of a matched set The bearings are usually mounted in pairs. This
of 9000UDT and 7000DT flush ground bearings arrangement divides the thrust load in one direction
having a 29˚ contact angle. The 97000H Series while accommodating reversing thrust load.
consists of a matched set of 9000HDT (split outer To increase thrust capacity in one direction it is
ring) and 7000DT flush ground bearings. possible to mount additional 7000DT or 7000PDT
bearings in tandem.
97207U2 35 1.3780 72 2.8346 34 1.3386 1.0 .04 .60 .024 37 700 8 480 34 000 7 640 7 400 9 600
97208U2 40 1.5748 80 3.1496 36 1.4173 1.0 .04 .60 .024 49 400 11 100 45 500 10 200 6 200 8 000
97209U2 45 1.7717 85 3.3465 38 1.4961 1.0 .04 .60 .024 49 400 11 100 46 500 10 500 5 800 7 600
97210U2 50 1.9685 90 3.5433 40 1.5748 1.0 .04 .60 .024 54 000 12 100 54 000 12 100 5 100 6 600
97211U2 55 2.1654 100 3.9370 42 1.6535 1.5 .06 1.0 .040 79 300 17 800 75 000 16 900 4 800 6 200
97212U2 60 2.3622 110 4.3307 44 1.7323 1.5 .06 1.0 .040 85 200 19 100 88 000 19 800 4 300 5 600
97213U2 65 2.5591 120 4.7244 46 1.8110 1.5 .06 1.0 .040 104 000 23 400 110 000 24 700 3 900 5 100
97214U2 70 2.7559 125 4.9213 48 1.8898 1.5 .06 1.0 .040 104 000 23 400 110 000 24 700 3 700 4 800
97215U2 75 2.9528 130 5.1181 50 1.9685 1.5 .06 1.0 .040 130 000 29 200 140 000 31 500 3 400 4 500
97216U2 80 3.1496 140 5.5118 52 2.0472 2.0 .08 1.0 .040 121 000 27 200 134 000 30 100 3 300 4 200
97217U2 85 3.3465 150 5.9055 56 2.2047 2.0 .08 1.0 .040 148 000 33 300 166 000 37 300 3 000 3 900
97218U2 90 3.5433 160 6.2992 60 2.3622 2.0 .08 1.0 .040 190 000 42 700 236 000 53 100 2 900 3 800
97219U2 95 3.7402 170 6.6929 64 2.5197 2.0 .08 1.0 .040 199 000 44 700 228 000 51 300 2 800 3 600
97220U2 100 3.9370 180 7.0866 68 2.6772 2.0 .08 1.0 .040 225 000 50 600 260 000 58 500 2 600 3 300
97221U2 105 4.1339 190 7.4803 72 2.8346 2.0 .08 1.0 .040 242 000 54 400 295 000 66 300 2 400 3 100
97222U2 110 4.3307 200 7.8740 76 2.9921 2.0 .08 1.0 .040 265 000 59 600 310 000 69 700 2 300 3 000
97224U2 120 4.7244 215 8.4646 80 3.1496 2.0 .08 1.0 .040 281 000 63 200 355 000 79 800 2 200 2 800
97226U2 130 5.1181 230 9.0551 80 3.1496 2.5 .10 1.0 .040 319 000 71 700 415 000 93 300 2 000 2 600
97228U2 140 5.5118 250 9.8425 84 3.3071 2.5 .10 1.0 .040 338 000 76 000 465 000 105 000 1 800 2 400
97230U2 150 5.9055 270 10.6299 90 3.5433 2.5 .10 1.0 .040 397 000 89 200 560 000 126 000 1 700 2 200
97232U2 160 6.2992 290 11.4173 96 3.7795 2.5 .10 1.0 .040 442 000 99 400 670 000 135 000 1 600 2 100
97234U2 170 6.6929 310 12.2047 104 4.0945 3.0 .12 1.0 .040 468 000 105 000 735 000 165 000 1 500 2 000
97236U2 180 7.0866 320 12.5984 104 4.0945 3.0 .12 1.0 .040 494 000 111 000 780 000 175 000 1 500 1 900
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
For thrust rating multiply C by 1.32 and C0 by 2.94.
3) Listed values are for machined brass cage.
178
97300 U2 Medium Series
97307U2 35 1.3780 80 3.1496 42 1.6535 1.5 .06 1.0 .040 58 500 13 200 48 000 10 800 6 800 8 800
97308U2 40 1.5748 90 3.5433 46 1.8110 1.5 .06 1.0 .040 71 500 16 100 61 000 13 700 5 800 7 600
97309U2 45 1.7717 100 3.9370 50 1.9685 1.5 .06 1.0 .040 85 200 19 200 75 000 16 900 5 100 6 600
97310U2 50 1.9685 110 4.3307 54 2.1260 2.0 .08 1.0 .040 121 000 27 200 106 000 23 800 4 600 6 000
97311U2 55 2.1654 120 4.7244 58 2.2835 2.0 .08 1.0 .040 140 000 31 500 125 000 28 100 4 100 5 300
97312U2 60 2.3622 130 5.1181 62 2.4409 2.0 .08 1.0 .040 159 000 35 700 146 000 32 800 3 900 5 100
97313U2 65 2.5591 140 5.5118 66 2.5984 2.0 .08 1.0 .040 178 000 40 000 173 000 38 900 3 700 4 800
97314U2 70 2.7559 150 5.9055 70 2.7559 2.0 .08 1.0 .040 182 000 40 900 170 000 38 200 3 300 4 200
97315U2 75 2.9528 160 6.2992 74 2.9134 2.0 .08 1.0 .040 225 000 50 600 228 000 51 300 3 100 4 000
97316U2 80 3.1496 170 6.6929 78 3.0709 2.0 .08 1.0 .040 234 000 52 600 240 000 54 000 2 900 3 800
97317U2 85 3.3465 180 7.0866 82 3.2283 2.5 .10 1.0 .040 265 000 59 600 285 000 64 100 2 800 3 600
97318U2 90 3.5433 190 7.4803 86 3.3858 2.5 .10 1.0 .040 276 000 62 000 300 000 67 400 2 600 3 400
97319U2 95 3.7402 200 7.8740 90 3.5433 2.5 .10 1.0 .040 291 000 65 400 325 000 73 100 2 500 3 200
97320U2 100 3.9370 215 8.4646 94 3.7008 2.5 .10 1.0 .040 312 000 70 100 365 000 82 100 2 400 3 100
97321U2 105 4.1339 225 8.8583 98 3.8583 2.5 .10 1.0 .040 332 000 74 600 400 000 89 900 2 300 3 000
97322U2 110 4.3307 240 9.4488 100 3.9370 2.5 .10 1.0 .040 371 000 83 400 475 000 107 000 2 200 2 800
97324U2 120 4.7244 260 10.2362 110 4.3307 2.5 .10 1.0 .040 423 000 95 100 560 000 126 000 2 000 2 600
97326U2 130 5.1181 280 11.0236 116 4.5669 3.0 .12 1.0 .040 468 000 105 000 640 000 144 000 1 800 2 400
97328U2 140 5.5118 300 11.8110 124 4.8819 3.0 .12 1.0 .040 507 000 114 000 735 000 165 000 1 800 2 200
97330U2 150 5.9055 320 12.5984 130 5.1181 3.0 .12 1.0 .040 559 000 126 000 865 000 194 000 1 600 2 100
97332U2 160 6.2992 340 13.3858 136 5.3543 3.0 .12 1.0 .040 618 000 139 000 965 000 217 000 1 500 2 000
97334U2 170 6.6929 360 14.1732 144 5.6693 3.0 .12 1.0 .040 650 000 146 000 1 040 000 234 000 1 500 1 900
97336U2 180 7.0866 380 14.9606 150 5.9055 3.0 .12 1.0 .040 689 000 155 000 1 160 000 261 000 1 400 1 800
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
For thrust rating multiply C by 1.32 and C0 by 2.94.
3) Listed values are for machined brass cage.
179
97200 UP2 Light Series MRC Bearing Services
97207UP2 35 1.3780 72 2.8346 34 1.3386 1.0 .04 .60 .024 47 500 10 700 39 000 8 770 6 300 8 500
97208UP2 40 1.5748 80 3.1496 36 1.4173 1.0 .04 .60 .024 52 700 11 800 45 000 10 100 5 600 7 500
97209UP2 45 1.7717 85 3.3465 38 1.4961 1.0 .04 .60 .024 62 400 14 000 55 000 12 400 5 300 7 000
97210UP2 50 1.9685 90 3.5433 40 1.5748 1.0 .04 .60 .024 65 000 14 600 60 000 13 500 4 800 6 300
97211UP2 55 2.1654 100 3.9370 42 1.6535 1.5 .06 1.0 .040 79 300 17 800 75 000 16 900 4 500 6 000
97212UP2 60 2.3622 110 4.3307 44 1.7323 1.5 .06 1.0 .040 95 600 21 500 91 600 20 600 4 000 5 300
97213UP2 65 2.5591 120 4.7244 46 1.8110 1.5 .06 1.0 .040 104 000 23 400 100 000 22 500 3 600 4 800
97214UP2 70 2.7559 125 4.9213 48 1.8898 1.5 .06 1.0 .040 112 000 25 200 112 000 25 200 3 400 4 500
97215UP2 75 2.9528 130 5.1181 50 1.9685 1.5 .06 1.0 .040 117 000 26 300 120 000 27 000 3 200 4 300
97216UP2 80 3.1496 140 5.5118 52 2.0472 2.0 .08 1.0 .040 135 000 30 300 140 000 31 500 3 000 4 000
97217UP2 85 3.3465 150 5.9055 56 2.2047 2.0 .08 1.0 .040 156 000 35 100 166 000 37 300 2 800 3 800
97218UP2 90 3.5433 160 6.2992 60 2.3622 2.0 .08 1.0 .040 178 000 40 000 190 000 42 700 2 600 3 600
97219UP2 95 3.7402 170 6.6929 64 2.5197 2.0 .08 1.0 .040 199 000 44 700 220 000 49 500 2 400 3 400
97220UP2 100 3.9370 180 7.0866 68 2.6772 2.0 .08 1.0 .040 212 000 47 700 250 000 56 200 2 200 3 200
97221UP2 105 4.1339 190 7.4803 72 2.8346 2.0 .08 1.0 .040 229 000 51 500 260 000 58 500 2 000 3 000
97222UP2 110 4.3307 200 7.8740 76 2.9921 2.0 .08 1.0 .040 251 000 56 400 310 000 69 700 1 900 2 800
97224UP2 120 4.7244 215 8.4646 80 3.1496 2.0 .08 1.0 .040 270 000 60 700 325 000 73 100 1 700 2 400
97226UP2 130 5.1181 230 9.0551 80 3.1496 2.5 .10 1.0 .040 302 000 67 900 390 000 87 700 1 700 2 400
97228UP2 140 5.5118 250 9.8425 84 3.3071 2.5 .10 1.0 .040 319 000 71 700 430 000 96 700 1 600 2 200
97230UP2 150 5.9055 270 10.6299 90 3.5433 2.5 .10 1.0 .040 351 000 78 900 520 000 117 000 1 500 2 000
97232UP2 160 6.2992 290 11.4173 96 3.7795 2.5 .10 1.0 .040 390 000 87 700 560 000 126 000 1 300 1 700
97234UP2 170 6.6929 310 12.2047 104 4.0945 3.0 .12 1.0 .040 436 000 98 000 655 000 147 000 1 200 1 600
97236UP2 180 7.0866 320 12.5984 104 4.0945 3.0 .12 1.0 .040 449 000 101 000 710 000 160 000 1 100 1 500
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
For thrust rating multiply C by 1.76 and C0 by 3.86.
3) Listed values are for machined brass cage.
180
97300 UP2 Medium Series
97307UP2 35 1.3780 80 3.1496 42 1.6535 1.5 .06 1.0 .040 63 700 14 300 49 000 11 000 6 000 8 000
97308UP2 40 1.5748 90 3.5433 46 1.8110 1.5 .06 1.0 .040 76 100 17 100 61 000 13 700 5 300 7 000
97309UP2 45 1.7717 100 3.9370 50 1.9685 1.5 .06 1.0 .040 97 500 21 900 80 000 18 000 4 800 6 300
97310UP2 50 1.9685 110 4.3307 54 2.1260 2.0 .08 1.0 .040 112 000 25 200 104 000 23 400 4 300 5 600
97311UP2 55 2.1654 120 4.7244 58 2.2835 2.0 .08 1.0 .040 130 000 29 200 112 000 25 200 3 800 5 000
97312UP2 60 2.3622 130 5.1181 62 2.4409 2.0 .08 1.0 .040 148 000 33 300 129 000 29 000 3 600 4 800
97313UP2 65 2.5591 140 5.5118 66 2.5984 2.0 .08 1.0 .040 165 000 37 100 160 000 36 000 3 200 4 300
97314UP2 70 2.7559 150 5.9055 70 2.7559 2.0 .08 1.0 .040 190 000 42 700 186 000 41 800 3 000 4 000
97315UP2 75 2.9528 160 6.2992 74 2.9134 2.0 .08 1.0 .040 208 000 46 800 200 000 45 000 2 800 3 800
97316UP2 80 3.1496 170 6.6929 78 3.0709 2.0 .08 1.0 .040 225 000 50 600 220 000 49 500 2 600 3 600
97317UP2 85 3.3465 180 7.0866 82 3.2283 2.5 .10 1.0 .040 238 000 53 500 245 000 55 100 2 400 3 400
97318UP2 90 3.5433 190 7.4803 86 3.3858 2.5 .10 1.0 .040 255 000 57 300 270 000 60 700 2 200 3 200
97319UP2 95 3.7402 200 7.8740 90 3.5433 2.5 .10 1.0 .040 276 000 62 000 300 000 67 400 2 000 3 000
97320UP2 100 3.9370 215 8.4646 94 3.7008 2.5 .10 1.0 .040 307 000 69 000 380 000 85 400 1 900 2 800
97321UP2 105 4.1339 225 8.8583 98 3.8583 2.5 .10 1.0 .040 325 000 73 100 390 000 87 700 1 800 2 600
97322UP2 110 4.3307 240 9.4488 100 3.9370 2.5 .10 1.0 .040 345 000 77 600 455 000 102 000 1 700 2 400
97324UP2 120 4.7244 260 10.2362 110 4.3307 2.5 .10 1.0 .040 390 000 87 700 530 000 119 000 1 600 2 200
97326UP2 130 5.1181 280 11.0236 116 4.5669 3.0 .12 1.0 .040 449 000 101 000 610 000 137 000 1 500 2 000
97328UP2 140 5.5118 300 11.8110 124 4.8819 3.0 .12 1.0 .040 488 000 110 000 695 000 156 000 1 400 1 900
97330UP2 150 5.9055 320 12.5984 130 5.1181 3.0 .12 1.0 .040 540 000 121 000 780 000 175 000 1 200 1 700
97332UP2 160 6.2992 340 13.3858 136 5.3543 3.0 .12 1.0 .040 553 000 124 000 850 000 191 000 1 200 1 600
97334UP2 170 6.6929 360 14.1732 144 5.6693 3.0 .12 1.0 .040 605 000 136 000 965 000 217 000 1 000 1 500
97336UP2 180 7.0866 380 14.9606 150 5.9055 3.0 .12 1.0 .040 650 000 146 000 1 100 000 247 000 950 1 400
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
For thrust rating multiply C by 1.76and C0 by 3.86.
3) Listed values are for machined brass cage.
181
MRC Bearing Services
97000 U2 Series
29° Angular Contact Ball Bearings
Duplex
Life rating
3
L10 = (CP) (millions of revolutions)
or
6 3
L10h =
10 C
60n P
() (Hours)
182
97000 U2 Series
29° Angular Contact Ball Bearings
Duplex
Case 1
Thrust load (FA) = 5000
FA 5000
FR
=
0
= ∞
FA
Since > 0.80,
FR
P = 0.39 FR + 0.76 FA = 0.76 × 5000
P = 3800
C = 40000
3 3
Life (L10) = (CP) = (40000
3800 )
= 1166 × 106 Rev.
or 6 3 6 3
40000
10 C
() 10
Life (L10h) = 60n P = 60 × 1750 3800 ( )
= 11108 Hours
Case 2
Radial load (FR) = 3000
Thrust load (FA) = 5000
FA 5000
FR = 3000 = 1.67
F
Since A > 0.80,
FR
P = 0.39 FR + 0.76 FA = 0.39 × 3000 + 0.76 × 5000
P = 4970
C = 40000
3 3
Life (L10) = (CP) = (40000
4970 )
= 521 × 106 Rev.
or 6 3 6 3
40000
10 C
() 10
Life (L10h) = 60n P = 60 × 1750 4970 ( )
= 4965 Hours
183
MRC Bearing Services
Life rating
3
L10 = (CP) (millions of revolutions)
or
6 3
L10h =
10 C
60n P
() (Hours)
184
97000 UP2 Series
40° Angular Contact Ball Bearings
Duplex
Case 1
Thrust load (FA) = 5000
FA 5000
FR = 0 = ∞
FA
Since FR > 1.14,
3 3
Life (L10) = (CP) = (42700
2850 )
= 3363 × 106 Rev.
or 6 3 6 3
42700
10 C
() 10
Life (L10h) = 60n P = 60 × 1750 2850( )
= 32030 Hours
Case 2
Radial load (FR) = 3000
Thrust load (FA) = 5000
FA 5000
FR = 3000 = 1.67
FA
Since F > 1.14,
R
185
186
Precision Bearings
ABEC-5 and ABEC-7 Tolerance Grades
187
Precision 15° Angular Contact
1900-R Extremely Light Series
(Single Bearings) MRC Bearing Services
For equivalent load and life calculations see pages 116 and 117.
1900R 10 .3937 22 .8661 6 .2362 .30 .012 .10 .004 110 .17 3 120 701 1 560 351 76 000 110 000
1901R 12 .4724 24 .9449 6 .2362 .30 .012 .10 .004 123 .19 3 250 731 1 800 405 69 000 100 000
1902R 15 .5906 28 1.1024 7 .2756 .30 .012 .10 .004 187 .29 4 880 1 100 2 700 607 55 000 84 000
1903R 17 .6693 30 1.1811 7 .2756 .30 .012 .10 .004 206 .32 5 400 1 210 3 000 674 51 000 78 000
1904R 20 .7874 37 1.4567 9 .3543 .30 .012 .15 .006 400 .62 9 360 2 100 5 850 1 320 41 000 62 000
1905R 25 .9843 42 1.6535 9 .3543 .30 .012 .15 .006 342 .53 7 610 1 710 5 300 1 190 37 000 53 000
1906R 30 1.1811 47 1.8504 9 .3543 .30 .012 .15 .006 452 .70 9 750 2 190 7 100 1 600 32 000 48 000
1907R 35 1.3780 55 2.1654 10 .3937 .64 .025 .15 .006 555 .86 11 200 2 520 9 000 2 020 25 000 39 000
1908R 40 1.5748 62 2.4409 12 .4724 .64 .025 .15 .006 722 1.12 14 300 3 210 11 600 2 600 23 000 36 000
1909R 45 1.7717 68 2.6772 12 .4724 .64 .025 .15 .006 806 1.25 15 100 3 400 13 400 3 010 21 000 31 000
1910R 50 1.9685 72 2.8346 12 .4724 .64 .025 .15 .006 1 070 1.66 19 500 4 380 17 300 3 900 20 000 28 000
1911R 55 2.1654 80 3.1496 13 .5118 1.0 .04 .30 .012 1 260 1.95 22 900 5 150 20 400 4 590 18 000 27 000
1912R 60 2.3622 85 3.3465 13 .5118 1.0 .04 .30 .012 1 390 2.15 24 200 5 440 22 800 5 130 17 000 25 000
1913R 65 2.5591 90 3.5433 13 .5118 1.0 .04 .30 .012 1 450 2.25 24 700 5 550 24 000 5 400 15 000 22 000
1914R 70 2.7559 100 3.9370 16 .6299 1.0 .04 .30 .012 1 990 3.09 33 200 7 460 32 500 7 300 14 000 21 000
1915R 75 2.9528 105 4.1339 16 .6299 1.0 .04 .30 .012 2 080 3.23 34 500 7 760 34 500 7 760 14 000 20 000
1916R 80 3.1496 110 4.3307 16 .6299 1.0 .04 .30 .012 2 180 3.38 34 500 7 760 36 000 8 100 13 000 19 000
1917R 85 3.3465 120 4.7244 18 .7087 1.0 .04 .60 .024 2 840 4.40 44 900 10 100 46 500 10 500 12 000 18 000
1918R 90 3.5433 125 4.9213 18 .7087 1.0 .04 .60 .024 3 400 5.27 52 700 11 800 56 000 12 600 12 000 17 000
1919R 95 3.7402 130 5.1181 18 .7087 1.0 .04 .60 .024 3 090 4.79 47 500 10 700 52 000 11 700 11 000 16 000
1920R 100 3.9370 140 5.5118 20 .7874 1.0 .04 .60 .024 3 870 6.00 58 500 13 200 64 000 14 400 10 000 15 000
1921R 105 4.1339 145 5.7087 20 .7874 1.0 .04 .60 .024 4 030 6.25 60 500 13 600 67 000 15 100 10 000 14 000
1922R 110 4.3307 150 5.9055 20 .7874 1.0 .04 .60 .024 3 820 5.93 55 300 12 400 64 000 14 400 9 200 13 000
1924R 120 4.7244 165 6.4961 22 .8661 1.0 .04 .60 .024 5 100 7.91 74 100 16 700 85 000 19 100 8 300 12 000
1926R 130 5.1181 180 7.0866 24 .9449 1.5 .06 .60 .024 6 300 9.77 90 400 20 500 106 000 23 800 7 800 11 000
1928R 140 5.5118 190 7.4803 24 .9449 1.5 .06 .60 .024 6 580 10.2 95 600 21 400 110 000 24 700 7 400 11 000
1930R 150 5.9055 210 8.2677 28 1.1024 2.0 .08 1.0 .040 9 090 14.1 125 000 28 200 150 000 33 700 6 400 9 500
1932R 160 6.2992 220 8.6614 28 1.1024 2.0 .08 1.0 .040 9 420 14.6 127 000 28 600 156 000 35 100 6 000 9 000
1934R 170 6.6929 230 9.0551 28 1.1024 2.0 .08 1.0 .040 10 200 15.8 133 000 29 800 170 000 38 300 5 500 8 400
1936R 180 7.0866 250 9.8425 33 1.2992 2.0 .08 1.0 .040 12 800 19.9 168 000 36 000 212 000 47 800 5 100 7 800
1938R 190 7.4803 260 10.2362 33 1.2992 2.0 .08 1.0 .040 13 400 20.7 174 000 39 100 224 000 50 400 5 100 7 800
1940R 200 7.8740 280 11.0236 38 1.4961 2.0 .08 1.0 .040 16 800 26.0 216 000 48 600 275 000 61 800 4 600 7 300
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
3) Values have been determined through historical application and practice. For a more complete explanation, see pg. 274.
188
Precision 15° Angular Contact
1900-RD Extremely Light Series
Duplex
“D” indicates a duplex ground half pair matched with an identical half pair and is
followed by an additional suffix letter to describe the type of duplex. See pages
234 and 235 for suffix description.
For equivalent load and life calculations see pages 118 and 119.
Use these values for back-to-back (DB) or face-to-face (DF) mounting arrangements.
1900RD 10 .3937 22 .8661 12 .4724 .30 .012 .10 .004 110 .17 5 070 1 140 3 100 697 61 000 88 000
1901RD 12 .4724 24 .9449 12 .4724 .30 .012 .10 .004 123 .19 5 270 1 180 3 550 798 55 000 80 000
1902RD 15 .5906 28 1.1024 14 .5512 .30 .012 .10 .004 187 .29 7 930 1 780 5 400 1 210 44 000 67 000
1903RD 17 .6693 30 1.1811 14 .5512 .30 .012 .10 .004 206 .32 8 710 1 960 6 100 1 370 41 000 62 000
1904RD 20 .7874 37 1.4567 18 .7087 .30 .012 .15 .006 400 .62 15 300 3 440 11 600 2 600 33 000 50 000
1905RD 25 .9843 42 1.6535 18 .7087 .30 .012 .15 .006 342 .53 12 400 2 790 10 800 2 430 30 000 42 000
1906RD 30 1.1811 47 1.8504 18 .7087 .30 .012 .15 .006 452 .70 15 900 3 580 14 300 3 210 26 000 38 000
1907RD 35 1.3780 55 2.1654 20 .7874 .64 .025 .15 .006 555 .86 18 200 4 090 18 000 4 050 20 000 31 000
1908RD 40 1.5748 62 2.4409 24 .9449 .64 .025 .15 .006 722 1.12 22 900 5 150 23 200 5 220 18 000 29 000
1909RD 45 1.7717 68 2.6772 24 .9449 .64 .025 .15 .006 806 1.25 24 700 5 550 26 500 5 960 17 000 25 000
1910RD 50 1.9685 72 2.8346 24 .9449 .64 .025 .15 .006 1 070 1.66 31 900 7 170 34 500 7 760 16 000 22 000
1911RD 55 2.1654 80 3.1496 26 1.0236 1.0 .04 .30 .012 1 260 1.95 37 100 8 340 40 500 9 100 14 000 22 000
1912RD 60 2.3622 85 3.3465 26 1.0236 1.0 .04 .30 .012 1 390 2.15 39 000 8 770 45 500 10 200 14 000 20 000
1913RD 65 2.5591 90 3.5433 26 1.0236 1.0 .04 .30 .012 1 450 2.25 39 700 8 920 48 000 10 800 12 000 18 000
1914RD 70 2.7559 100 3.9370 32 1.2598 1.0 .04 .30 .012 1 990 3.09 54 000 12 100 65 500 14 700 11 000 17 000
1915RD 75 2.9528 105 4.1339 32 1.2598 1.0 .04 .30 .012 2 080 3.23 55 900 12 600 68 000 15 300 11 000 16 000
1916RD 80 3.1496 110 4.3307 32 1.2598 1.0 .04 .30 .012 2 180 3.38 57 200 12 900 72 000 16 200 10 000 15 000
1917RD 85 3.3465 120 4.7244 36 1.4173 1.0 .04 .60 .024 2 840 4.40 74 100 16 700 93 000 20 900 9 600 14 000
1918RD 90 3.5433 125 4.9213 36 1.4173 1.0 .04 .60 .024 3 400 5.27 85 200 19 200 112 000 25 200 9 600 14 000
1919RD 95 3.7402 130 5.1181 36 1.4173 1.0 .04 .60 .024 3 090 4.79 76 100 17 100 104 000 23 400 8 800 13 000
1920RD 100 3.9370 140 5.5118 40 1.5748 1.0 .04 .60 .024 3 870 6.00 95 600 21 500 127 000 28 600 8 000 12 000
1921RD 105 4.1339 145 5.7087 40 1.5748 1.0 .04 .60 .024 4 030 6.25 97 500 21 900 134 000 30 100 8 000 11 000
1922RD 110 4.3307 150 5.9055 40 1.5748 1.0 .04 .60 .024 3 820 5.93 90 400 20 300 129 000 29 000 7 400 10 000
1924RD 120 4.7244 165 6.4961 44 1.7323 1.0 .04 .60 .024 5 100 7.91 121 000 27 200 170 000 38 200 6 600 9 600
1926RD 130 5.1181 180 7.0866 48 1.8898 1.5 .06 .60 .024 6 300 9.77 146 000 32 800 208 000 46 800 6 200 8 800
1928RD 140 5.5118 190 7.4803 48 1.8898 1.5 .06 .60 .024 6 580 10.2 156 000 35 100 220 000 49 500 5 900 8 800
1930RD 150 5.9055 210 8.2677 56 2.2047 2.0 .08 1.0 .040 9 090 14.1 203 000 45 600 300 000 67 400 5 100 7 600
1932RD 160 6.2992 220 8.6614 56 2.2047 2.0 .08 1.0 .040 9 420 14.6 208 000 46 800 315 000 70 800 4 800 7 200
1934RD 170 6.6929 230 9.0551 56 2.2047 2.0 .08 1.0 .040 10 200 15.8 216 000 48 600 340 000 76 400 4 400 6 700
1936RD 180 7.0866 250 9.8425 66 2.5984 2.0 .08 1.0 .040 12 800 19.9 276 000 62 000 425 000 95 600 4 100 6 200
1938RD 190 7.4803 260 10.2362 66 2.5984 2.0 .08 1.0 .040 13 400 20.7 281 000 63 200 440 000 98 900 4 100 6 200
1940RD 200 7.8740 280 11.0236 76 2.9921 2.0 .08 1.0 .040 16 800 26.0 351 000 78 900 550 000 124 000 3 700 5 800
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
3) Values have been determined through historical application and practice. For a more complete explanation, see pg. 274.
189
Precision 15° Angular Contact
100-KR Extra Light Series
(Single Bearings) MRC Bearing Services
For equivalent load and life calculations see pages 116 and 117.
100KR 10 .3937 26 1.0236 8 .3150 .30 .012 .10 .004 181 .28 4 940 1 110 2 280 513 69 000 100 000
101KR 12 .4724 28 1.1024 8 .3150 .30 .012 .10 .004 206 .32 5 530 1 240 2 650 596 60 000 90 000
102KR 15 .5906 32 1.2598 9 .3543 .30 .012 .10 .004 226 .35 6 050 1 350 3 150 708 51 000 78 000
103KR 17 .6693 35 1.3780 10 .3937 .30 .012 .10 .004 342 .53 8 520 1 920 4 650 1 050 44 000 67 000
104KR 20 .7874 42 1.6535 12 .4724 .64 .025 .30 .012 445 .69 10 800 2 420 6 200 1 390 39 000 56 000
105KR 25 .9843 47 1.8504 12 .4724 .64 .025 .30 .012 522 .81 12 100 2 720 7 650 1 720 35 000 50 000
106KR 30 1.1811 55 2.1654 13 .5118 1.0 .04 .30 .012 716 1.11 15 600 3 500 10 600 2 380 28 000 42 000
107KR 35 1.3780 62 2.4409 14 .5512 1.0 .04 .30 .012 884 1.37 18 600 4 180 13 200 2 970 23 000 36 000
108KR 40 1.5748 68 2.6772 15 .5906 1.0 .04 .30 .012 942 1.46 19 500 4 380 14 600 3 280 22 000 34 000
109KR 45 1.7717 75 2.9528 16 .6299 1.0 .04 .30 .012 1 220 1.89 24 200 5 440 19 000 4 270 21 000 31 000
110KR 50 1.9685 80 3.1496 16 .6299 1.0 .04 .30 .012 1 300 2.01 25 100 5 640 20 400 4 590 20 000 28 000
111KR 55 2.1654 90 3.5433 18 .7087 1.0 .04 .60 .024 1 810 2.81 33 800 7 600 28 000 6 290 17 000 25 000
112KR 60 2.3622 95 3.7402 18 .7087 1.0 .04 .60 .024 1 920 2.97 35 100 7 890 30 000 6 740 15 000 22 000
113KR 65 2.5591 100 3.9370 18 .7087 1.0 .04 .60 .024 2 030 3.14 35 800 8 050 32 500 7 310 14 000 21 000
114KR 70 2.7559 110 4.3307 20 .7874 1.0 .04 .60 .024 2 470 3.83 42 300 9 510 40 000 8 990 14 000 20 000
115KR 75 2.9528 115 4.5276 20 .7874 1.0 .04 .60 .024 2 590 4.02 43 600 9 800 42 500 9 550 13 000 19 000
116KR 80 3.1496 125 4.9213 22 .8661 1.0 .04 .60 .024 3 390 5.25 55 900 12 600 54 000 12 100 12 000 18 000
117KR 85 3.3465 130 5.1181 22 .8661 1.0 .04 .60 .024 3 550 5.50 57 200 12 900 57 000 12 800 12 000 17 000
118KR 90 3.5433 140 5.5118 24 .9449 1.5 .06 .60 .024 4 280 6.64 68 900 15 500 68 000 15 300 11 000 16 000
119KR 95 3.7402 145 5.7087 24 .9449 1.5 .06 .60 .024 5 040 7.81 83 200 18 700 80 000 18 000 10 000 15 000
120KR 100 3.9370 150 5.9055 24 .9449 1.5 .06 .60 .024 4 700 7.28 71 500 16 100 76 500 17 200 10 000 14 000
121KR 105 4.1339 160 6.2992 26 1.0236 2.0 .08 1.0 .040 5 540 8.59 85 200 19 200 90 000 20 200 9 200 13 000
122KR 110 4.3307 170 6.6929 28 1.1024 2.0 .08 1.0 .040 6 400 9.93 99 500 22 400 102 000 23 000 8 700 13 000
124KR 120 4.7244 180 7.0866 28 1.1024 2.0 .08 1.0 .040 6 710 10.4 101 000 22 600 110 000 24 700 7 800 11 000
126KR 130 5.1181 200 7.8740 33 1.2992 2.0 .08 1.0 .040 9 350 14.5 138 000 31 000 150 000 33 700 7 400 11 000
128KR 140 5.5118 210 8.2677 33 1.2992 2.0 .08 1.0 .040 9 350 14.5 135 000 30 300 153 000 34 400 6 900 10 000
130KR 150 5.9055 225 8.8583 35 1.3780 2.0 .08 1.0 .040 10 800 16.8 156 000 35 000 176 000 39 600 6 000 9 000
132KR 160 6.2992 240 9.4488 38 1.4961 2.0 .08 1.0 .040 12 400 19.3 178 000 40 000 204 000 45 900 5 500 8 400
134KR 170 6.6929 260 10.2362 42 1.6535 2.0 .08 1.0 .040 15 300 23.7 212 000 47 700 245 000 55 100 5 100 7 800
136KR 180 7.0866 280 11.0236 46 1.8110 2.0 .08 1.0 .040 17 900 27.8 234 000 52 600 290 000 65 200 4 600 7 300
138KR 190 7.4803 290 11.4173 46 1.8110 2.0 .08 1.0 .040 18 800 29.1 242 000 54 400 305 000 68 600 4 600 7 300
140KR 200 7.8740 310 12.2047 51 2.0079 2.0 .08 1.0 .040 22 200 34.4 276 000 62 000 355 000 79 800 4 400 6 700
144KR 220 8.6614 340 13.3858 56 2.2047 2.5 .10 1.0 .040 30 400 47.2 345 000 77 600 480 000 108 000 4 100 6 200
148KR 240 9.4488 360 14.1732 56 2.2047 2.5 .10 1.0 .040 31 900 49.5 351 000 78 900 510 000 115 000 3 900 5 600
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
3)
Values have been determined through historical application and practice. For a more complete explanation, see pg. 274.
190
Precision 15° Angular Contact
100-KRD Extra Light Series
Duplex
“D” indicates a duplex ground half pair matched with an identical half pair and is
followed by an additional suffix letter to describe the type of duplex. See pages
234 and 235 for suffix description.
For equivalent load and life calculations see pages 118 and 119.
Use these values for back-to-back (DB) or face-to-face (DF) mounting arrangements.
100KRD 10 .3937 26 1.0236 16 .6299 .30 .012 .10 .004 181 .28 8.060 1 810 4 550 1 020 55 000 80 000
101KRD 12 .4724 28 1.1024 16 .6299 .30 .012 .10 .004 206 .32 8 840 1 990 5 300 1 190 48 000 72 000
102KRD 15 .5906 32 1.2598 18 .7087 .30 .012 .10 .004 226 .35 9 750 2 190 6 300 1 420 41 000 62 000
103KRD 17 .6693 35 1.3780 20 .7874 .30 .012 .10 .004 342 .53 13 800 3 100 9 300 2 090 35 000 54 000
104KRD 20 .7874 42 1.6535 24 .9449 .64 .025 .30 .012 445 .69 17 400 3 910 12 500 2 810 31 000 45 000
105KRD 25 .9843 47 1.8504 24 .9449 .64 .025 .30 .012 522 .81 19 500 4 380 15 300 3 440 28 000 40 000
106KRD 30 1.1811 55 2.1654 26 1.0236 1.0 .04 .30 .012 716 1.11 25 500 5 730 21 200 4 760 22 000 34 000
107KRD 35 1.3780 62 2.4409 28 1.1024 1.0 .04 .30 .012 884 1.37 30 200 6 790 26 500 5 960 18 000 29 000
108KRD 40 1.5748 68 2.6772 30 1.1811 1.0 .04 .30 .012 942 1.46 31 900 7 170 29 000 6 520 18 000 27 000
109KRD 45 1.7717 75 2.9528 32 1.2598 1.0 .04 .30 .012 1 220 1.89 39 000 8 770 37 500 8 430 17 000 25 000
110KRD 50 1.9685 80 3.1496 32 1.2598 1.0 .04 .30 .012 1 300 2.01 40 300 9 060 40 500 9 100 16 000 22 000
111KRD 55 2.1654 90 3.5433 36 1.4173 1.0 .04 .60 .024 1 810 2.81 55 300 12 400 56 000 12 600 14 000 20 000
112KRD 60 2.3622 95 3.7402 36 1.4173 1.0 .04 .60 .024 1 920 2.97 55 900 12 600 61 000 13 700 12 000 18 000
113KRD 65 2.5591 100 3.9370 36 1.4173 1.0 .04 .60 .024 2 030 3.14 58 500 13 200 64 000 14 400 11 000 17 000
114KRD 70 2.7559 110 4.3307 40 1.5748 1.0 .04 .60 .024 2 470 3.83 68 900 15 500 80 000 18 000 11 000 16 000
115KRD 75 2.9528 115 4.5276 40 1.5748 1.0 .04 .60 .024 2 590 4.02 70 200 15 800 85 000 19 100 10 000 15 000
116KRD 80 3.1496 125 4.9213 44 1.7323 1.0 .04 .60 .024 3 390 5.25 90 400 20 300 110 000 24 700 9 600 14 000
117KRD 85 3.3465 130 5.1181 44 1.7323 1.0 .04 .60 .024 3 550 5.50 92 300 20 700 116 000 26 100 9 600 14 000
118KRD 90 3.5433 140 5.5118 48 1.8898 1.5 .06 .60 .024 4 280 6.64 111 000 25 000 137 000 30 800 8 800 13 000
119KRD 95 3.7402 145 5.7087 48 1.8898 1.5 .06 .60 .024 5 040 7.81 135 000 30 300 160 000 36 000 8 000 12 000
120KRD 100 3.9370 150 5.9055 48 1.8898 1.5 .06 .60 .024 4 700 7.28 117 000 26 300 153 000 34 400 8 000 11 000
121KRD 105 4.1339 160 6.2992 52 2.0472 2.0 .08 1.0 .040 5 540 8.59 138 000 31 000 180 000 40 500 7 400 10 000
122KRD 110 4.3307 170 6.6929 56 2.2047 2.0 .08 1.0 .040 6 400 9.93 163 000 36 600 204 000 45 900 7 000 10 000
124KRD 120 4.7244 180 7.0866 56 2.2047 2.0 .08 1.0 .040 6 710 10.4 163 000 36 600 220 000 49 500 6 200 8 800
126KRD 130 5.1181 200 7.8740 66 2.5984 2.0 .08 1.0 .040 9 350 14.5 225 000 50 000 300 000 67 400 5 900 8 800
128KRD 140 5.5118 210 8.2677 66 2.5984 2.0 .08 1.0 .040 9 350 14.5 221 000 49 700 305 000 68 600 5 500 8 000
130KRD 150 5.9055 225 8.8583 70 2.7559 2.0 .08 1.0 .040 10 800 16.8 255 000 57 300 355 000 79 800 4 800 7 200
132KRD 160 6.2992 240 9.4488 76 2.9921 2.0 .08 1.0 .040 12 400 19.3 286 000 64 300 405 000 91 000 4 400 6 700
134KRD 170 6.6929 260 10.2362 84 3.3071 2.0 .08 1.0 .040 15 300 23.7 345 000 77 600 490 000 110 000 4 100 6 200
136KRD 180 7.0866 280 11.0236 92 3.6220 2.0 .08 1.0 .040 17 900 27.8 377 000 84 800 570 000 128 000 3 700 5 800
138KRD 190 7.4803 290 11.4173 92 3.6220 2.0 .08 1.0 .040 18 800 29.1 390 000 87 700 610 000 137 000 3 700 5 800
140KRD 200 7.8740 310 12.2047 102 4.0157 2.0 .08 1.0 .040 22 200 34.4 442 000 99 400 710 000 160 000 3 500 5 400
144KRD 220 8.6614 340 13.3858 112 4.4094 2.5 .10 1.0 .040 30 400 47.2 559 000 126 000 965 000 217 000 3 300 5 000
148KRD 240 9.4488 360 14.1732 112 4.4094 2.5 .10 1.0 .040 31 900 49.5 572 000 129 000 1 020 000 228 000 3 100 4 500
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
3)
Values have been determined through historical application and practice. For a more complete explanation, see pg. 274.
191
Precision 15° Angular Contact
200-R Light Series
(Single Bearings) MRC Bearing Services
For equivalent load and life calculations see pages 116 and 117.
200R 10 .3937 30 1.1811 9 .3543 .64 .025 .30 .012 284 .44 7 280 1 640 3 200 719 55 000 84 000
201R 12 .4724 32 1.2598 10 .3937 .64 .025 .30 .012 323 .50 8 190 1 840 3 900 877 51 000 78 000
202R 15 .5906 35 1.3780 11 .4331 .64 .025 .30 .012 406 .63 9 750 2 190 5 100 1 150 44 000 67 000
203R 17 .6693 40 1.5748 12 .4724 .64 .025 .30 .012 510 .79 12 100 2 730 6 550 1 470 39 000 56 000
204R 20 .7874 47 1.8504 14 .5512 1.0 .04 .60 .024 562 .87 13 300 2 990 7 800 1 750 35 000 50 000
205R 25 .9843 52 2.0472 15 .5906 1.0 .04 .60 .024 693 1.07 15 900 3 570 9 650 2 170 28 000 42 000
206R 30 1.1811 62 2.4409 16 .6299 1.0 .04 .60 .024 884 1.37 19 000 4 270 12 900 2 910 23 000 36 000
207R 35 1.3780 72 2.8346 17 .6693 1.0 .04 .60 .024 1 270 1.97 26 000 5 850 18 600 4 180 21 000 31 000
208R 40 1.5748 80 3.1496 18 .7087 1.0 .04 .60 .024 1 730 2.68 34 500 7 760 25 000 5 620 20 000 28 000
209R 45 1.7717 85 3.3465 19 .7480 1.0 .04 .60 .024 1 850 2.87 35 800 8 050 27 500 6 180 17 000 25 000
210R 50 1.9685 90 3.5433 20 .7874 1.0 .04 .60 .024 1 970 3.06 37 700 8 480 30 000 6 740 16 000 24 000
211R 55 2.1654 100 3.9370 21 .8268 1.5 .06 1.0 .040 2 860 4.43 54 000 12 100 41 500 9 330 14 000 21 000
212R 60 2.3622 110 4.3307 22 .8661 1.5 .06 1.0 .040 3 260 5.06 59 200 13 300 49 000 11 000 14 000 20 000
213R 65 2.5591 120 4.7244 23 .9055 1.5 .06 1.0 .040 3 780 5.86 58 500 13 200 55 000 12 400 12 000 18 000
214R 70 2.7559 125 4.9213 24 .9449 1.5 .06 1.0 .040 4 030 6.25 71 500 16 100 60 000 13 500 12 000 17 000
215R 75 2.9528 130 5.1181 25 .9843 1.5 .06 1.0 .040 4 880 7.56 85 200 19 200 72 000 16 200 11 000 16 000
216R 80 3.1496 140 5.5118 26 1.0236 2.0 .08 1.0 .040 5 180 8.04 90 400 20 300 78 000 17 500 10 000 15 000
217R 85 3.3465 150 5.9055 28 1.1024 2.0 .08 1.0 .040 6 170 9.56 104 000 23 400 93 000 20 900 10 000 14 000
218R 90 3.5433 160 6.2992 30 1.1811 2.0 .08 1.0 .040 7 410 11.5 124 000 27 900 108 000 24 300 8 700 13 000
219R 95 3.7402 170 6.6929 32 1.2598 2.0 .08 1.0 .040 7 900 12.3 133 000 29 900 118 000 26 500 8 300 12 000
220R 100 3.9370 180 7.0866 34 1.3386 2.0 .08 1.0 .040 9 070 14.1 146 000 32 800 134 000 30 100 7 800 11 000
221R 105 4.1339 190 7.4803 36 1.4173 2.0 .08 1.0 .040 10 300 16.0 168 000 37 800 153 000 34 400 7 400 11 000
222R 110 4.3307 200 7.8740 38 1.4961 2.0 .08 1.0 .040 11 700 18.1 182 000 40 900 170 000 38 200 6 900 10 000
224R 120 4.7244 215 8.4646 40 1.5748 2.0 .08 1.0 .040 13 000 20.2 199 000 44 700 193 000 43 300 6 400 9 500
226R 130 5.1181 230 9.0551 40 1.5748 2.5 .10 1.0 .040 15 500 24.0 221 000 49 600 232 000 52 200 6 000 9 000
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
3)
Values have been determined through historical application and practice. For a more complete explanation, see pg. 274.
192
Precision 15° Angular Contact
200-RD Light Series
Duplex
“D” indicates a duplex ground half pair matched with an identical half pair and is
followed by an additional suffix letter to describe the type of duplex. See pages
234 and 235 for suffix description.
For equivalent load and life calculations see pages 118 and 119.
Use these values for back-to-back (DB) or face-to-face (DF) mounting arrangements.
200RD 10 .3937 30 1.1811 18 .7087 .64 .025 .30 .012 284 .44 11 900 2 680 6 400 1 440 44 000 67 000
201RD 12 .4724 32 1.2598 20 .7874 .64 .025 .30 .012 323 .50 13 300 2 990 7 800 1 750 41 000 62 000
202RD 15 .5906 35 1.3780 22 .8661 .64 .025 .30 .012 406 .63 15 900 3 570 10 200 2 290 35 000 54 000
203RD 17 .6693 40 1.5748 24 .9449 .64 .025 .30 .012 510 .79 19 900 4 470 13 200 2 970 31 000 45 000
204RD 20 .7874 47 1.8504 28 1.1024 1.0 .04 .60 .024 562 .87 21 600 4 860 15 600 3 510 28 000 40 000
205RD 25 .9843 52 2.0472 30 1.1811 1.0 .04 .60 .024 693 1.07 26 000 5 850 19 300 4 340 22 000 34 000
206RD 30 1.1811 62 2.4409 32 1.2598 1.0 .04 .60 .024 884 1.37 30 700 6 900 26 000 5 850 18 000 29 000
207RD 35 1.3780 72 2.8346 34 1.3386 1.0 .04 .60 .024 1 270 1.97 42 300 9 570 37 500 8 430 17 000 25 000
208RD 40 1.5748 80 3.1496 36 1.4173 1.0 .04 .60 .024 1 730 2.68 55 900 12 600 50 000 11 200 16 000 22 000
209RD 45 1.7717 85 3.3465 38 1.4961 1.0 .04 .60 .024 1 850 2.87 58 500 13 200 55 000 12 400 14 000 20 000
210RD 50 1.9685 90 3.5433 40 1.5748 1.0 .04 .60 .024 1 970 3.06 60 500 13 600 60 000 13 500 13 000 19 000
211RD 55 2.1654 100 3.9370 42 1.6535 1.5 .06 1.0 .040 2 860 4.43 87 100 19 600 83 000 18 700 11 000 17 000
212RD 60 2.3622 110 4.3307 44 1.7323 1.5 .06 1.0 .040 3 260 5.06 95 600 21 500 98 000 22 000 11 000 16 000
213RD 65 2.5591 120 4.7244 46 1.8110 1.5 .06 1.0 .040 3 780 5.86 95 600 21 500 110 000 24 700 9 600 14 000
214RD 70 2.7559 125 4.9213 48 1.8898 1.5 .06 1.0 .040 4 030 6.25 117 000 26 300 120 000 27 000 9 600 14 000
215RD 75 2.9528 130 5.1181 50 1.9685 1.5 .06 1.0 .040 4 880 7.56 138 000 31 000 148 000 32 100 8 800 13 000
216RD 80 3.1496 140 5.5118 52 2.0472 2.0 .08 1.0 .040 5 180 8.04 153 000 34 400 156 000 35 100 8 000 12 000
217RD 85 3.3465 150 5.9055 56 2.2047 2.0 .08 1.0 .040 6 170 9.56 168 000 37 800 186 000 41 800 8 000 11 000
218RD 90 3.5433 160 6.2992 60 2.3622 2.0 .08 1.0 .040 7 410 11.5 203 000 45 600 216 000 48 600 7 000 10 000
219RD 95 3.7402 170 6.6929 64 2.5197 2.0 .08 1.0 .040 7 900 12.3 216 000 48 600 236 000 53 100 6 600 9 600
220RD 100 3.9370 180 7.0866 68 2.6772 2.0 .08 1.0 .040 9 070 14.1 238 000 53 500 270 000 60 700 6 200 8 800
221RD 105 4.1339 190 7.4803 72 2.8346 2.0 .08 1.0 .040 10 300 16.0 270 000 60 700 305 000 68 600 5 900 8 800
222RD 110 4.3307 200 7.8740 76 2.9921 2.0 .08 1.0 .040 11 700 18.1 296 000 66 500 340 000 76 400 5 500 8 000
224RD 120 4.7244 215 8.4646 80 3.1496 2.0 .08 1.0 .040 13 000 20.2 325 000 73 100 390 000 87 700 5 100 7 600
226RD 130 5.1181 230 9.0551 80 3.1496 2.5 .10 1.0 .040 15 500 24.0 358 000 80 500 465 000 105 000 4 800 7 200
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
3)
Values have been determined through historical application and practice. For a more complete explanation, see pg. 274.
193
Precision 15° Angular Contact
300-R Medium Series
(Single Bearings) MRC Bearing Services
For equivalent load and life calculations see pages 116 and 117.
300R 10 .3937 35 1.3780 11 .4331 1.0 .04 .60 .024 439 .68 10 500 2 360 4 550 1 020 46 000 73 000
301R 12 .4724 37 1.4567 12 .4724 1.0 .04 .60 .024 439 .68 10 600 2 380 4 900 1 100 44 000 67 000
302R 15 .5906 42 1.6535 13 .5118 1.0 .04 .60 .024 510 .79 12 100 2 720 6 550 1 470 39 000 56 000
303R 17 .6693 47 1.8504 14 .5512 1.0 .04 .60 .024 632 .98 14 800 3 330 8 150 1 830 37 000 53 000
304R 20 .7874 52 2.0472 15 .5906 1.0 .04 .60 .024 909 1.41 20 300 4 560 11 400 2 560 30 000 45 000
305R 25 .9843 62 2.4409 17 .6693 1.0 .04 .60 .024 1 090 1.69 23 400 5 260 15 300 3 440 25 000 39 000
306R 30 1.1811 72 2.8346 19 .7480 1.0 .04 .60 .024 1 480 2.30 31 200 7 010 20 000 4 500 21 000 31 000
307R 35 1.3780 80 3.1496 21 .8268 1.5 .06 1.0 .040 1 940 3.00 39 700 8 920 26 000 5 850 20 000 28 000
308R 40 1.5748 90 3.5433 23 .9055 1.5 .06 1.0 .040 2 450 3.80 48 800 11 000 33 500 7 530 17 000 25 000
309R 45 1.7717 100 3.9370 25 .9843 1.5 .06 1.0 .040 3 030 4.69 58 500 13 200 40 500 9 100 15 000 22 000
310R 50 1.9685 110 4.3307 27 1.0630 2.0 .08 1.0 .040 3 990 6.19 76 100 17 100 52 000 11 700 14 000 21 000
311R 55 2.1654 120 4.7244 29 1.1417 2.0 .08 1.0 .040 4 690 7.26 88 400 19 900 61 000 13 700 13 000 19 000
312R 60 2.3622 130 5.1181 31 1.2205 2.0 .08 1.0 .040 5 430 8.42 101 000 22 700 71 000 16 000 12 000 17 000
313R 65 2.5591 140 5.5118 33 1.2992 2.0 .08 1.0 .040 5 930 9.19 108 000 24 300 80 000 18 000 11 000 16 000
314R 70 2.7559 150 5.9055 35 1.3780 2.0 .08 1.0 .040 6 770 10.5 121 000 27 200 93 000 20 900 10 000 15 000
315R 75 2.9528 160 6.2992 37 1.4567 2.0 .08 1.0 .040 8 390 13.0 146 000 32 800 114 000 25 600 9 900 14 000
316R 80 3.1496 170 6.6929 39 1.5354 2.0 .08 1.0 .040 9 480 14.7 159 000 35 700 129 000 29 000 8 700 13 000
317R 85 3.3465 180 7.0866 41 1.6142 2.5 .10 1.0 .040 10 600 16.5 174 000 39 100 146 000 32 800 8 300 12 000
318R 90 3.5433 190 7.4803 43 1.6929 2.5 .10 1.0 .040 11 800 18.3 186 000 41 800 160 000 36 000 7 800 11 000
319R 95 3.7402 200 7.8740 45 1.7717 2.5 .10 1.0 .040 13 100 20.3 199 000 44 700 180 000 40 500 7 400 11 000
320R 100 3.9370 215 8.4646 47 1.8504 2.5 .10 1.0 .040 14 400 22.4 212 000 47 700 200 000 45 000 6 900 10 000
321R 105 4.1339 225 8.8583 49 1.9291 2.5 .10 1.0 .040 15 900 24.6 229 000 51 500 204 000 45 900 6 400 9 500
322R 110 4.3307 240 9.4488 50 1.9685 2.5 .10 1.0 .040 18 800 29.2 255 000 57 300 255 000 57 300 6 000 9 000
324R 120 4.7244 260 10.2362 55 2.1654 2.5 .10 1.0 .040 22 100 34.3 265 000 59 600 300 000 67 400 5 800 8 400
326R 130 5.1181 280 11.0236 58 2.2835 3.0 .12 1.0 .040 25 700 39.8 296 000 66 500 345 000 77 600 5 300 7 800
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
3)
Values have been determined through historical application and practice. For a more complete explanation, see pg. 274.
194
Precision 15° Angular Contact
300-RD Medium Series
Duplex
“D” indicates a duplex ground half pair matched with an identical half pair and is
followed by an additional suffix letter to describe the type of duplex. See pages
234 and 235 for suffix description.
For equivalent load and life calculations see pages 118 and 119.
Use these values for back-to-back (DB) or face-to-face (DF) mounting arrangements.
300RD 10 .3937 35 1.3780 22 .8661 1.0 .04 .60 .024 439 .68 17 200 3 870 9 150 2 060 37 000 58 000
301RD 12 .4724 37 1.4567 24 .9449 1.0 .04 .60 .024 439 .68 17 200 3 870 9 800 2 200 35 000 54 000
302RD 15 .5906 42 1.6535 26 1.0236 1.0 .04 .60 .024 510 .79 19 900 4 470 13 200 2 970 31 000 45 000
303RD 17 .6693 47 1.8504 28 1.1024 1.0 .04 .60 .024 632 .98 24 200 5 440 16 300 3 660 30 000 42 000
304RD 20 .7874 52 2.0472 30 1.1811 1.0 .04 .60 .024 909 1.41 33 200 7 460 22 800 5 130 24 000 36 000
305RD 25 .9843 62 2.4409 34 1.3386 1.0 .04 .60 .024 1 090 1.69 37 700 8 480 30 500 6 860 20 000 31 000
306RD 30 1.1811 72 2.8346 38 1.4961 1.0 .04 .60 .024 1 480 2.30 50 700 11 400 40 000 8 990 17 000 25 000
307RD 35 1.3780 80 3.1496 42 1.6535 1.5 .06 1.0 .040 1 940 3.00 65 000 14 600 52 000 11 700 16 000 22 000
308RD 40 1.5748 90 3.5433 46 1.8110 1.5 .06 1.0 .040 2 450 3.80 79 300 17 800 67 000 15 100 14 000 20 000
309RD 45 1.7717 100 3.9370 50 1.9685 1.5 .06 1.0 .040 3 030 4.69 95 600 21 500 81 500 18 300 12 000 18 000
310RD 50 1.9685 110 4.3307 54 2.1260 2.0 .08 1.0 .040 3 990 6.19 124 000 27 900 104 000 23 400 11 000 17 000
311RD 55 2.1654 120 4.7244 58 2.2835 2.0 .08 1.0 .040 4 690 7.26 143 000 32 100 122 000 27 400 10 000 15 000
312RD 60 2.3622 130 5.1181 62 2.4409 2.0 .08 1.0 .040 5 430 8.42 165 000 37 100 143 000 32 100 9 600 14 000
313RD 65 2.5591 140 5.5118 66 2.5984 2.0 .08 1.0 .040 5 930 9.19 174 000 39 100 160 000 36 000 8 800 13 000
314RD 70 2.7559 150 5.9055 70 2.7559 2.0 .08 1.0 .040 6 770 10.5 195 000 43 800 186 000 41 800 8 000 12 000
315RD 75 2.9528 160 6.2992 74 2.9134 2.0 .08 1.0 .040 8 390 13.0 238 000 53 500 228 000 51 300 8 000 11 000
316RD 80 3.1496 170 6.6929 78 3.0709 2.0 .08 1.0 .040 9 480 14.7 260 000 58 500 260 000 58 500 7 000 10 000
317RD 85 3.3465 180 7.0866 82 3.2283 2.5 .10 1.0 .040 10 600 16.5 281 000 63 200 290 000 65 200 6 600 9 600
318RD 90 3.5433 190 7.4803 86 3.3858 2.5 .10 1.0 .040 11 800 18.3 302 000 67 900 320 000 71 900 6 200 8 800
319RD 95 3.7402 200 7.8740 90 3.5433 2.5 .10 1.0 .040 13 100 20.3 325 000 73 100 360 000 80 900 5 900 8 800
320RD 100 3.9370 215 8.4646 94 3.7008 2.5 .10 1.0 .040 14 400 22.4 345 000 77 600 400 000 89 900 5 500 8 000
321RD 105 4.1339 225 8.8583 98 3.8583 2.5 .10 1.0 .040 15 900 24.6 371 000 83 400 405 000 91 000 5 100 7 600
322RD 110 4.3307 240 9.4488 100 3.9370 2.5 .10 1.0 .040 18 800 29.2 416 000 93 500 510 000 115 000 4 800 7 200
324RD 120 4.7244 260 10.2362 110 4.3307 2.5 .10 1.0 .040 22 100 34.3 436 000 98 000 600 000 135 000 4 600 6 700
326RD 130 5.1181 280 11.0236 116 4.5669 3.0 .12 1.0 .040 25 700 39.8 475 000 107 000 695 000 156 000 4 200 6 200
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
3)
Values have been determined through historical application and practice. For a more complete explanation, see pg. 274.
195
MRC ABEC-5 High Precision Deep Groove
Ball Bearings for Woodworking Machinery MRC Bearing Services
General Information
Ball Bearings manufactured specifically for the controlled internal characteristics, providing very
woodworking industry often carry special good shaft rigidity and precise control of axial and
specifications in order to meet the requirements of radial runout.
both high speed and accuracy. As a result of
The bearings are available with bakelite (phenolic),
actively participating in this market for many years,
pressed brass, or glass reinforced polyamide
MRC has designed a line of deep groove ball
cages, as illustrated below.
bearings that meet the special needs of the
woodworking industry. They are high precision Recommended mounting fits are shown on pages
bearings with carefully 258 to 259 in the shaft and housing fit section.
Bearing Identification
Example of marking on MRC Bearing Box
207S-BRS#5 C2
Identification of Marking
2 07 S BRS #5 C2
Series
Bore Size
Single Row Deep Groove
Cage Material
BRS = Brass
BKE = Bakelite
NYL = polyamide
Precision Class ABEC-5
Internal Radial Clearance
C2 = Tight
C0 = Standard
C3 = Loose
196
Ball Screw Support Bearings
Duplex Quadruplex
DF DFDT
The MRC ball screw support bearing is a single-row These ball screw support bearings are designed for
angular contact nonseparable bearing with one use in numerically controlled machine tools where
heavy race shoulder and one counterbored race standard angular contact bearings or roller bearings
shoulder on the outer ring. The inner ring is similar cannot deliver the rigidity levels required. The 60 ˚
in design having a counterbored race shoulder. contact angle contributes to maximum axial rigidity
and gives very stiff screw support to maintain the
Construction and ring design permit a greater number accuracy of the ball screw.
Cage Types and Materials
of balls than the standard angular contact types, and
result in a very high thrust load-carrying capacity. The
60˚ initial contact angle provides maximum axial rigidity.
One-piece molded polyamide, ball-riding cages are
As heavy thrust must be taken in both directions, these
supplied with ball screw support bearings.
angular contact bearings are mounted in duplex pairs.
For even stiffer screw support, the bearings can be
mounted in quadruple sets.
These bearings are made in ABEC-7 tolerance grade
only. Inner and outer rings and balls are of AISI 52100
steel. Retainers are a ball-riding type of molded
polyamide composition.
197
Ball Screw Support Bearings MRC Bearing Services
Duplex Quadruplex
Sets Sets
J078DF 20.000 .7874 47.000 1.8504 31.750 1.2500 .80 .031 .003 .0001 12 100 2 720 10 000 2 250
J093DF 23.838 .9385 62.000 2.4409 31.750 1.2500 .80 .031 .003 .0001 13 800 3 100 13 700 3 080
J098DF 25.000 .9843 62.000 2.4409 31.750 1.2500 .80 .031 .003 .0001 13 800 3 100 13 700 3 080
J150DF 38.100 1.5000 72.000 2.8346 31.750 1.2500 .80 .031 .003 .0001 14 600 3 280 15 300 3 440
J175DF 44.475 1.7510 76.200 3.0000 31.750 1.2500 .80 .031 .003 .0001 15 100 3 390 16 600 3 730
J225DF 57.150 2.2500 90.000 3.5433 31.750 1.2500 .80 .031 .003 .0001 16 300 3 660 20 000 4 500
J300DF 76.200 3.0000 110.000 4.3307 31.750 1.2500 .80 .031 .003 .0001 17 800 4 000 25 500 5 730
J400DF 101.600 4.0000 145.000 5.7087 44.450 1.7500 1.0 .040 .003 .0001 36 400 8 180 52 000 11 700
Quadruplex Sets
J078DFDT 20.000 .7874 47.000 1.8504 63.500 2.5000 .80 .031 .003 .0001 19 500 4 380 20 000 4 500
J093DFDT 23.838 .9385 62.000 2.4409 63.500 2.5000 .80 .031 .003 .0001 22 500 5 060 26 500 5 960
J098DFDT 25.000 .9843 62.000 2.4409 63.500 2.5000 .80 .031 .003 .0001 22 500 5 060 26 500 5 960
J150DFDT 38.100 1.5000 72.000 2.8346 63.500 2.5000 .80 .031 .003 0001 23 800 5 350 30 500 6 860
J175DFDT 44.475 1.7510 76.200 3.0000 63.500 2.5000 .80 .031 .003 .0001 24 700 5 550 33 500 7 530
J225DFDT 57.150 2.2500 90.000 3.5433 63.500 2.5000 .80 .031 .003 .0001 26 500 5 960 40 000 8 990
J300DFDT 76.200 3.0000 110.000 4.3307 63.500 2.5000 .80 .031 .003 .0001 29 100 6 540 51 000 11 500
J400DFDT 101.600 4.0000 145.000 5.7087 88.900 3.5000 1.0 .040 .003 .0001 59 200 13 300 104 000 23 400
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2) For thrust rating multiply C by 1.70 and Co by 4.00.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
198
High Precision Bearings
For Ex-Cell-O Spindles
Each MRC bearing made for Ex-Cell-O®‚ spindles is a Shaft and House Fitting Practices
separable inner ring type with counterbored outer ring,
with the cage and ball assembly remaining together Basic dimensions of this new Ex-Cell-O bearing series
as a unit. The bearings are manufactured to a basic remain the same as bearings previously furnished. The
ABEC-7 grade with a minus tolerance on the nominal only external dimensional differences are in the bore
bore and O.D. The cage, which is outer ring land- and O.D. tolerances, and these must be considered
guided, has a chamfer on the bore to provide for when replacing the old series bearings. Current fitting
improved flow of lubricant. practices in Ex-Cell-O spindles are 0.0001˝ tight to
0.0001˝ loose on the shaft, 0.0003˝ loose to 0.0005˝
These bearings are packed in pairs, with one bearing loose in the floating end of the housing and 0.0001˝
of the pair marked with a single burnished dot on both loose to 0.0003˝ loose in the held end of the housing.
inner and outer ring faces. The other bearing is marked Therefore, it may be necessary to alter shaft and
with two burnished dots on both the inner and outer housing seat diameters to retain correct fitting
rings. These dots help avoid mixing of the separable practices.
How To Order
bearing parts and also indicate high points of
eccentricity on inner and outer rings.
Identification Markings The dimension table on the next two pages provides all
MRC replacement bearing numbers and corresponding
Ball bearings furnished for replacement use are Ex-Cell-O part numbers. When ordering, specify MRC
identical to those provided for Ex-Cell-O OEM use bearing number, operating speed or preload, or both to
except for identification markings. The small table assure delivery of proper bearing for application.
Difference Between Old and New Types
below shows typical markings on inner and outer rings
of MRC replacement bearings and Ex-Cell-O bearings.
MRC Ex-Cell-O Basic external dimensions are the same with only a
Replacement OEM change in tolerance of the bore and O.D. in the new
Bearings Bearings
type. The new ball cage provides a chamfer on the
Inner Ring MRC USA D MRC USA D
Outer Ring XO-30-RBDS-16 XLO-30-57 bore for better flow of lubricant. One shoulder of the
inner ring is low enough to permit separation from the
Note that both the OEM and replacement bearings outer ring, ball and cage assembly.
have the same marking on the inner ring—MRC USA D.
However, on the outer ring of the OEM bearings, a
typical marking shows XLO-30-57: XLO is the Ex-Cell-O
trademark, 30 indicates the basic bearing size, 57
denotes preload group 5 (not preload in pounds) and
tolerance grade ABEC-7. MRC replacement bearings
are marked XO-30-RBDS-16 on the outer ring: XO
designates Ex-Cell-O bearings, 30 shows the basic
bearing number, RBDS indicates duplex bearings with
a preload of 16 pounds.
199
High-Precision Bearings
For Ex-Cello-O Spindles MRC Bearing Services
XO-20-RBDS 20-27 9.53 .37500 28.58 1.1250 17.46 .6875 9.9 .3906 1.6 .0625
20-107
XO-30-RBDS 30-17 15.88 .62500 38.10 1.5000 25.4 1.000 16.4 .645 1.6 .0625
30-27
30-57
30-77
30-107
XO-55-RBDS 55-17 20.64 .81250 50.80 2.0000 25.4 1.000 21.4 .844 1.6 .063
55-27
55-57
55-87
55-107
XO-57-RBDS 57-17 26.99 1.06250 57.15 2.2500 25.4 1.000 27.5 1.082 1.6 .063
57-27
57-57
57-87
57-107
XO-67-RBDS 67-17 31.75 1.2500 61.91 2.4375 31.75 1.250 32.6 1.285 3.2 .125
67-37
67-57
67-87
67-107
XO-90-RBDS 90-17 41.28 1.6250 87.31 3.4375 41.28 1.625 42.2 1.660 3.2 .125
90-47
90-57
90-67
90-77
90-107
XO-115-RBDS 115-17 57.15 2.2500 120.7 4.7500 57.15 2.250 58.4 2.300 4.7 .187
115-27
115-37
115-47
115-57
115-77
XO-135-RBDS 135-27 31.75 1.2500 68.26 2.6875 31.75 1.250 32.6 1.285 3.2 .125
135-47
135-67
135-77
135-107
XO-155-RBDS 155-07 69.85 2.7500 120.7 4.7500 57.15 2.250 70.9 2.790 4.7 .187
155-17
155-37
155-47
155-67
155-87
155-107
XO-165-RBDS 165-17 88.903 3.50000 160.3 6.3125 76.2 3.000 89.5 3.525 6.4 .250
165-27
165-47
165-57
165-67
165-87
200
High-Precision Bearings
For Ex-Cell-O Spindles
MRC Fillet
Replacement Radius1) Maximum
Bearing ra Pre-Load Speed (RPM)
Number mm in Lbs. Grease Lub. Oil Lub. Mist Lub.
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
201
202
Specialty Bearings
Type Page
Adapter 204
Conveyor Roll 205
Dynamometer 207
Electric Motor Quality / ASMA cross reference 209
Felt Seal Replacement 224
Mast Guide 228
Wide Inner Ring 231
203
Adapter-Type Bearings,
Tapered Bore MRC Bearing Services
¹⁵|₁₆ 1 206-SFFX 62 2.4409 16 .6299 1.0 .04 SNW6 819 1.27 19 500 4 380 10 000 2 250 10 000 13 000 —
¹⁵|₁₆ 1 206-SZZX 62 2.4409 16 .6299 1.0 .04 SNW6 819 1.27 19 500 4 380 10 000 2 250 — — 7 500
1¹|₈ 1³|₁₆ 207-SFFX 72 2.8346 17 .6693 1.0 .04 SNW7 1 140 1.76 27 000 6 070 15 300 3 440 9 000 11 000 —
1¹|₈ 1³|₁₆ 207-SZZX 72 2.8346 17 .6693 1.0 .04 SNW7 1 140 1.76 27 000 6 070 15 300 3 440 — — 6 300
1⁷|₁₆ 209-SZZX 85 3.3465 19 .7480 1.0 .04 SNW9 1 640 2.54 36 400 8 180 22 800 5 130 — — 5 000
1³|₄ 210-SX 90 3.5433 20 .7874 1.0 .04 SNW10 1 610 2.50 35 100 7 890 23 200 5 210 7 000 8 500 4 800
1¹⁵|₁₆ 211-SX 100 3.9370 21 .8268 1.5 .06 SNW11 2 040 3.16 43 600 9 800 30 000 6 740 6 300 7 500 4 300
2¹|₁₆ 212-SZZX 110 4.3307 22 .8661 1.5 .06 SNW12 2 520 3.91 47 500 10 700 32 500 7 310 — — 4 000
2⁷|₁₆ 215-SZZX 130 5.1181 25 .9843 1.5 .06 SNW15 3 350 5.20 66 300 14 900 49 000 11 000 — — 3 200
3 217-SZZX 150 5.9055 28 1.1024 2.0 .08 SNW17 4 260 6.60 83 200 18 700 64 000 14 400 — — 2 800
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2) Listed values are for pressed steel or polyamide cage, ABEC-1.
The values have been determined through historical application and practice. For a more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
204
Conveyor Roll Bearings
Conveyor roll ball bearings are offered for use in either inboard or outboard roll
applications. Some types are designed for mounting directly into a roll, others are
designed with a milled slot in the outer ring for simplified bracket mounting. Seals in the
permanently lubricated bearing types retain lubricant for the life of the bearing, and
protect against entrance of foreign matter. Maximum adjustment for belt alignment is
provided, resulting in less belt wear. Cadmium-plated outer rings are supplied, except in
CONV-4SZZ-2.
Conveyor rolls equipped with CONV-504-3 bearings turn on stub shafts designed for
self-alignment in bearing bore and ease of removal. CONV-504-3 is fitted with synthetic
rubber seals which effectively seal out contaminants.
CONV-3-SF 3) .6243 1.6540 .9688 1.000 ⁷|₈ 1.469 ³|₁₆ ⁷|₁₆ .37 5 920 1 330 4 000 899
CONV-4-SF 3) .7874 1.9685 1.0000 1.0625 ²⁹|₃₂ 1.781 ⁹|₃₂ ⁷|₁₆ .55 13 500 3 030 11 400 2 560
CONV-4-SZZ2 .7505 1.7805 .610 — — — — — .22 13 500 3 030 11 400 2 560
1)
CONV-3-Y-2 replaced by CONV-3-Y-4. CONV-3-Y-2 did not have cadmium-plated outer ring and shields.
2) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
3) Check availability.
205
206
MRC Dynamometer Bearings
For several years, MRC Bearing Services has supplied specially designed bearings for dynamometer
applications. These bearings are manufactured with the following characteristics.
• ABEC 5 Inner Ring Tolerances.
• Inner ring eccentricity value, not to exceed 0.0005˝, marked on the inner ring face at the location of maximum
lateral runout.
• Special internal radial clearance.
• Special “E” Grade Balls.
• High speed, lightweight, inner ring land-guided phenolic (Bakelite) separators.
Dynamometer Bearing Identification
3 16 R DM – BKE
Series (300)
Bore Diameter Code (80MM)
“R” Type, Single Row, Maximum Capacity
Special Dynamometer Quality Features
Phenolic (Bakelite) Separator
These bearings were developed to minimize operating temperatures, noise and vibration in dynamometer
applications. To achieve best results the value of eccentricity marked on the inner ring face should be aligned 180˚
opposite the high point of eccentricity measured at the shaft journal. If the bearings are grease lubricated, they
should be carefully hand packed prior to installation to make sure that grease is worked into the close running
clearance between the O.D. of the inner ring and the I.D. of the separator.
300-RDM Series
307RDM4) 35 1.3780 80 3.1496 21 .8268 1.5 .06 1.0 .040 1 940 3.00 39 000 8 770 26 000 5 850 19 500 28 000
309RDM4) 45 1.7717 100 3.9370 25 .9843 1.5 .06 1.0 .040 3 030 4.69 58 500 13 200 40 500 9 100 15 400 22 400
310RDM4) 50 1.9685 110 4.3307 27 1.0630 2.0 .08 1.0 .040 4 350 6.75 80 600 18 100 57 000 12 800 14 500 21 000
311RDM4) 55 2.1654 120 4.7244 29 1.1417 2.0 .08 1.0 .040 5 110 7.92 93 600 21 000 67 000 15 100 12 900 18 700
312RDM4) 60 2.3622 130 5.1181 31 1.2205 2.0 .08 1.0 .040 5 930 9.19 108 000 24 300 78 000 17 500 11 500 16 800
313RDM4) 65 2.5591 140 5.5118 33 1.2992 2.0 .08 1.0 .040 6 900 10.7 121 000 27 200 93 000 20 900 11 000 15 700
315RDM 75 2.9528 160 6.2992 37 1.4567 2.0 .08 1.0 .040 9 050 14.0 153 000 34 400 122 000 27 400 9 900 14 000
316RDM 80 3.1496 170 6.6929 39 1.5354 2.0 .08 1.0 .040 9 480 14.7 159 000 35 700 129 000 29 000 8 700 12 600
318RDM 90 3.5433 190 7.4803 43 1.6929 2.5 .10 1.0 .040 11 800 18.3 185 000 41 600 160 000 36 000 7 800 11 200
320RDM 100 3.9370 215 8.4646 47 1.8504 2.5 .10 1.0 .040 14 400 22.4 212 000 47 700 200 000 45 000 6 900 10 100
321RDM4) 105 4.1339 225 8.8583 49 1.9291 2.5 .10 1.0 .040 15 900 24.6 229 000 51 500 204 000 45 900 6 400 9 500
322RDM4) 110 4.3307 240 9.4488 50 1.9685 2.5 .10 1.0 .040 18 800 29.2 255 000 57 300 255 000 57 300 6 000 9 000
324RDM4) 120 4.7244 260 10.2352 55 2.1654 2.5 .10 1.0 .040 22 100 34.3 265 000 59 600 300 000 67 400 6 000 8 400
326RDM4) 130 5.1181 280 11.0236 58 2.2835 3.0 .12 1.0 .040 25 700 39.8 296 000 66 500 345 000 77 600 5 300 7 800
328RDM4) 140 5.5118 300 11.8110 62 2.4409 3.0 .12 1.0 .040 29 500 45.7 351 000 78 900 400 000 89 900 4 800 7 300
330RDM4) 150 5.9055 320 12.5984 65 2.5591 3.0 .12 1.0 .040 33 900 52.6 390 000 87 700 475 000 107 000 4 600 6 700
332RDM4) 160 6.2992 340 13.3853 68 2.6772 3.0 .12 1.0 .040 38 400 59.6 423 000 95 100 530 000 119 000 4 100 6 200
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
Listed values are for inner ring land guided, phenolic composition cage.
The values have been determined through historical application and practice. For a more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
4) Typically non-stocked sizes, please check availability before designing into equipment.
207
208
ABMA Cross Reference
209
ABMA Identification Code
ABMA Standard 20, 1987 MRC Bearing Services
The ABMA (American Bearing Manufacturers identification of most general purpose bearings. If
Association) method of identification is arranged in additional assistance is required please contact MRC
five sections. An abbreviated explanation of each Bearing Services.
section is provided below. This information will allow
Section 1 Section 3
Bore—Bore Diameter in mm Internal fit
0 = Normal (ST)
Type
2 = Tight (TI)
BC –S BD 5000 BS 1200E 3 = Loose (LO)
BL –M BE 5000M BY 9000H 4 = Extra loose (XL)
BH –R BG 5000C BZ 9000U 5 = Greater than symbol 4
BA 7000 BF 5000M* BIC R(INCH)
BT 7000P BK 5000C** BIH XLS Duplex bearings
7 = Light preload
8 = Medium preload
Outside diameter and width 9 = Heavy preload
02 = 200 19 = 1900
03 = 300 32 = 5200 Tolerance
04 = 400 33 = 5300 0 = ABEC-1
10 = 100 34 = 5400 6 = ABEC-3
Section 2
5 = ABEC-5
4 = ABEC-7
2 = ABEC-9
Cage
J = Pressed steel Section 4
Y = Pressed brass
K = Machined bronze, land guided Lubricant
D = Non-metallic, land guided X = Manufacturers standard
T = Non-metallic, ball guided A = Specific lube to satisfy a particular condition
Section 5
V = No cage
X = Any cage acceptable
Shields and seals Special requirements
P = Permanently fastened shield See following page
D = Removable contact seal
H = Labyrinth seal
G= Contact seal, any type
X = Spacer used when no closure required *Radial type, 0˚ contact angle substitute 5000M.
**Radial type, 0˚ contact angle substitute 5000C.
Bearing ring modification
G= Snap ring in normal position
C = Snap ring in opposite position
N = Snap ring groove, less snap ring
A = Snap ring groove in opposite position, less snap
ring
Duplex mounting
D = Universally ground single bearing (DU)
R = DB pair
U = DF pair
T = DT pair
210
ABMA Identification Code
(ABMA Standard 20, 1987)
318SG
90BC03KXXN4026
90 = Bore in mm
BC = Type S
03 = 300 series
K = Machined bronze cage
XX = Spacers
N = Snap ring groove, less snap ring
4 = Extra loose fit (XL)
0 = ABEC-1
26 = Stabilize for operation at 300˚F
7205DU
25BA02DXXD0
25 = Bore in mm
BA = Type 7000
02 = 200 series
D = Phenolic cage
XX = Spacers
D = DU, ¹|₂ pair
0 = ABEC-1
211
ABMA Numbers and
MRC Equivalent MRC Bearing Services
212
ABMA Numbers and
MRC Equivalent
213
ABMA Numbers and
MRC Equivalent MRC Bearing Services
214
ABMA Numbers and
MRC Equivalent
215
ABMA Numbers and
MRC Equivalent MRC Bearing Services
216
ABMA Numbers and
MRC Equivalent
217
ABMA Numbers and
MRC Equivalent MRC Bearing Services
218
ABMA Numbers and
MRC Equivalent
219
ABMA Numbers and
MRC Equivalent MRC Bearing Services
220
ABMA Numbers and
MRC Equivalent
221
ABMA Numbers and
MRC Equivalent MRC Bearing Services
222
ABMA Numbers and
MRC Equivalent
100BC10X30 120KS
100BC10XD30 120KSZ
100BC10XDD30 120KSZZ
100BC10XDDG30 120KSZZG
100BC10XDXG30 120KSZG
100BC10XP30 120KSF
100BC10XPP30 120KSFF
100BC10XPPG30 120KSFFG
100BC10XPXG30 120KSFG
100BC10XXXG30 120KSG
100BC19X30 1920S
100BC19XD30 1920SZ
100BC19XDD30 1920SZZ
100BC19XP30 1920SF
100BC19XPP30 1920SFF
100BC32XDD30 220SZZC
100BC32XDDG30 220SZZCG
100BC32XPP30 220SFFC
100BC32XPPG30 220SFFCG
100BC33XDD30 320SZZC
100BC33XDDG30 320SZZCG
100BC33XPP30 320SFFC
100BC33XPPG30 320SFFCG
223
Felt Seal Replacement Bearings
Basic Dimensions MRC Bearing Services
8008 38FS1 8 .3150 24 .9449 8 .315 9.8 .386 10.3 .406 .30 .012 110 .17 3 320 746 1 430 321 23 000
8013 201FS2 13 .5118 32 1.2598 10 .394 12.2 .480 12.7 .500 .64 .025 245 .38 6 890 1 550 3 050 686 15 000
8014 202FS1 14 .5512 35 1.3780 11 .433 12.2 .480 12.7 .500 .64 .025 284 .44 7 610 1 710 3 650 821 13 000
8016 202FS3 16 .6299 35 1.3780 11 .433 12.2 .480 12.7 .500 .64 .025 284 .44 7 610 1 710 3 650 821 13 000
8026 205FS3 26 1.0236 52 2.0472 15 .591 15.2 .600 15.9 .625 1.0 .040 568 .88 14 000 3 150 8 000 1 800 8 500
8038 38FS 8 .3150 22 .8661 8 .315 9.8 .386 10.3 .406 .30 .012 110 .17 3 320 746 1 370 308 23 000
8500 200FS 10 .3937 30 1.1811 9 .354 12.2 .480 12.7 .500 .64 .025 155 .24 5 070 1 140 2 400 540 17 000
8501 201FS 12 .4724 32 1.2598 10 .394 12.2 .480 12.7 .500 .64 .025 245 .38 6 760 1 520 3 050 685 15 000
8502 202FS 15 .5906 35 1.3780 11 .433 12.2 .480 12.7 .500 .64 .025 277 .43 7 610 1 710 3 750 843 13 000
8503 203FS 17 .6693 40 1.5748 12 .472 13.7 .538 14.3 .563 .64 .025 361 .56 9 560 2 150 4 800 1 080 12 000
8504 204FS 20 .7874 47 1.8504 14 .551 15.2 .600 15.9 .625 1.0 .040 503 .78 13 000 2 920 6 700 1 510 10 000
8505 205FS 25 .9843 52 2.0472 15 .591 15.2 .600 15.9 .625 1.0 .040 568 .88 14 000 3 150 8 000 1 800 8 500
8506 206FS 30 1.1811 62 2.4409 16 .630 19 .748 20 .787 1.0 .040 813 1.26 19 500 4 380 11 400 2 560 7 500
8507 207FS 35 1.3780 72 2.8346 17 .669 20 .787 21 .827 1.0 .040 1 109 1.72 25 500 5 730 15 300 3 440 6 300
8508 208FS 40 1.5748 80 3.1496 21 .827 24 .945 24 .945 1.0 .040 1 320 2.05 29 100 6 540 18 000 4 050 5 600
8605 305FS 25 .9843 62 2.4409 17 .669 21 .827 21 .827 1.0 .040 632 .98 15 900 3 570 8 000 1 800 7 500
WC87008 38FSF2 8 .3150 24 .9449 10.3 .406 9.8 .386 10.3 .406 .30 .012 110 .17 3 320 746 1 430 321 23 000
WC87016 16 .6299 35 1.3780 12.7 .500 12.2 .480 12.7 .500 .64 .025 284 .44 7 610 1 710 3 750 843 13 000
WC87500 200FSF1 10 .3937 30 1.1811 12.7 .500 12.2 .480 12.7 .500 .64 .025 155 .24 5 070 1 140 2 400 540 17 000
WC87501 201FSF1 12 .4724 32 1.2598 12.7 .500 12.2 .480 12.7 .500 .64 .025 245 .38 6 890 1 550 2 400 540 15 000
WC87502 202FSF1 15 .5906 35 1.3780 12.7 .500 12.2 .480 12.7 .500 .64 .025 277 .43 7 610 1 710 3 750 843 13 000
WC87503 203FSF1 17 .6693 40 1.5748 14.3 .563 13.7 .538 14.3 .563 .64 .025 361 .56 9 560 2 150 4 800 1 080 12 000
WC87504 204FSF1 20 .7874 47 1.8504 15.9 .625 15.2 .600 15.9 .625 1.0 .040 503 .78 13 000 2 920 6 700 1 510 10 000
87007 37FSF1 7 .2756 24 .9449 8 .315 9.8 .386 10.3 .406 .30 .012 110 .17 3 320 746 1 430 321 23 000
87008 38FSF1 8 .3150 24 .9449 8 .315 9.8 .386 10.3 .406 .30 .012 110 .17 3 320 746 1 430 321 23 000
87013 201FSF3 13 .5118 32 1.2598 10 .394 12.2 .480 12.7 .500 .64 .025 245 .38 6 890 1 550 3 050 686 15 000
87014 14 .5512 35 1.3780 11 .433 12.2 .480 12.7 .500 .64 .025 284 .44 7 610 1 710 3 650 821 13 000
87016 202FSF4 16 .6299 35 1.3780 11 .433 12.2 .480 12.7 .500 .64 .025 284 .44 7 610 1 710 3 750 843 13 000
87026 26 1.0236 52 2.0472 15 .591 15.2 .600 15.9 .625 1.0 .040 568 .88 14 000 3 150 8 000 1 800 8 500
87036 36FSF 6 .2362 19 .7480 8 .315 9.8 .386 10.3 .406 .30 .012 97 .15 2 810 632 1 080 243 26 000
87037 37FSF 7 .2756 22 .8661 8 .315 9.8 .386 10.3 .406 .30 .012 110 .17 3 320 746 1 340 301 23 000
87038 38FSF 8 .3150 22 .8661 8 .315 9.8 .386 10.3 .406 .30 .012 110 .17 3 320 746 1 370 308 23 000
87500 200FSF 10 .3937 30 1.1811 9 .354 12.2 .480 12.7 .500 .64 .025 155 .24 5 070 1 140 2 400 540 17 000
87501 201FSF 12 .4724 32 1.2598 9 .394 12.2 .480 12.7 .500 .64 .025 245 .38 8 190 1 840 3 650 821 15 000
87502 202FSF 15 .5906 35 1.3780 11 .433 12.2 .480 12.7 .500 .64 .025 277 .43 7 610 1 710 3 750 843 13 000
87503 203FSF 17 .6693 40 1.5748 12 .472 13.7 .538 14.3 .563 .64 .025 361 .56 9 560 2 150 4 800 1 080 12 000
87504 204FSF 20 .7874 47 1.8504 14 .551 15.2 .600 15.9 .625 1.0 .040 503 .78 13 000 2 920 6 700 1 510 10 000
87505 205FSF 25 .9843 52 2.0472 15 .591 15.2 .600 15.9 .625 1.0 .040 568 .88 14 000 3 150 8 000 1 800 8 500
87506 206FSF 30 1.1811 62 2.4409 16 .630 19 .748 20 .787 1.0 .040 813 1.26 19 500 4 380 11 400 2 560 7 500
87507 207FSF 35 1.3780 72 2.8346 17 .669 20 .787 21 .827 1.0 .040 1 110 1.72 25 500 5 730 15 300 3 440 6 300
87508 208FSF 40 1.5748 80 3.1496 21 .827 24 .945 24 .945 1.0 .040 1 320 2.05 29 100 6 540 18 000 4 050 5 000
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
Listed values are for pressed steel or polyamide cage, ABEC-1.
The values have been determined through historical application and practice. For a more complete explanation, see page 274.
3) Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
224
Felt Seal Replacement Bearings
Basic Dimensions
88007 7 .2756 24 .9449 8 .315 12.6 .497 12.6 .497 .30 .012 110 .17 3 320 746 1 430 321 23 000
88008 38FFS2 8 .3150 24 .9449 8 .315 12.6 .497 12.6 .497 .30 .012 110 .17 3 320 746 1 430 321 23 000
88009 9 .3543 30 1.1811 9 .354 16.4 .646 16.4 .646 .64 .025 155 .24 4 620 1 040 2 040 459 17 000
88011 11 .4331 32 1.2598 10 .394 15.4 .606 15.4 .606 .64 .025 245 .38 6 760 1 520 3 000 674 15 000
88013 201FFS2 13 .5118 32 1.2598 10 .394 15.4 .606 15.4 .606 .64 .025 245 .38 6 890 1 550 3 050 686 15 000
88016 202FFS5 16 .6299 35 1.3780 11 .433 14.4 .567 14.4 .567 .64 .025 284 .44 7 610 1 710 3 750 843 13 000
88500 200FFS 10 .3937 30 1.1811 9 .354 16.4 .646 16.4 .646 .64 .025 155 .24 5 070 1 140 2 400 540 17 000
88501 201FFS 12 .4724 32 1.2598 10 .394 15.4 .606 15.4 .606 .64 .025 245 .38 6 760 1 520 3 050 685 15 000
88502 202FFS 15 .5906 35 1.3780 11 .433 14.4 .567 14.4 .567 .64 .025 277 .43 7 610 1 710 3 750 843 13 000
88503 203FFS 17 .6693 40 1.5748 12 .472 16.6 .654 16.6 .654 .64 .025 361 .56 9 560 2 150 4 800 1 080 12 000
88504 204FFS 20 .7874 47 1.8504 14 .551 17.8 .699 17.8 .699 1.0 .040 503 .78 13 000 2 920 6 700 1 510 10 000
88505 205FFS 25 .9843 52 2.0472 15 .591 16.7 .659 16.7 .659 1.0 .040 568 .88 14 000 3 150 8 000 1 800 8 500
88506 206FFS 30 1.1811 62 2.4409 16 .630 24 .945 24 .945 1.0 .040 813 1.26 19 500 4 380 11 400 2 560 7 500
88507 207FFS 35 1.3780 72 2.8346 17 .669 25 .984 25 .984 1.0 .040 1 110 1.72 25 500 5 730 15 300 3 440 6 300
88508 208FFS 40 1.5748 80 3.1496 21 .827 27 1.063 27 1.063 1.0 .040 1 320 2.05 29 100 6 540 18 000 4 050 5 600
487502 G202FSF 15 .5906 35 1.3780 11 .433 12.2 .480 12.7 .500 .64 .025 277 .43 7 610 1 710 3 750 843 13 000
487503 G203FSF 17 .6693 40 1.5748 12 .472 13.7 .538 14.3 .563 .64 .025 361 .56 9 560 2 150 4 800 1 080 12 000
487508 G208FSF 40 1.5748 80 3.1496 21 .827 24 .945 24 .945 1.0 .040 1 320 2.05 29 100 6 540 18 000 4 050 5 600
488016 202FFS2G 16 .6299 35 1.3780 11 .433 14.4 .567 14.4 .567 .64 .025 284 .44 7 610 1 710 3 750 843 13 000
488502 202FFSG 15 .5906 35 1.3780 11 .433 14.4 .567 14.4 .567 .64 .025 277 .43 7 610 1 710 3 750 843 13 000
488503 203FFSG 17 .6693 40 1.5748 12 .472 16.6 .654 16.6 .654 .64 .025 361 .56 9 560 2 150 4 800 1 080 12 000
488504 204FFSG 20 .7874 47 1.8504 14 .551 17.8 .699 17.8 .699 1.0 .040 503 .78 13 000 2 920 6 700 1 510 10 000
488505 205FFSG 25 .9843 52 2.0472 15 .591 16.7 .659 16.7 .659 1.0 .040 568 .88 14 000 3 150 8 000 1 800 8 500
488506 206FFSG 30 1.1811 62 2.4409 16 .630 24 .945 24 .945 1.0 .040 813 1.26 19 500 4 380 11 400 2 560 7 500
488507 207FFSG 35 1.3780 72 2.8346 17 .669 25 .984 25 .984 1.0 .040 1 110 1.72 25 500 5 730 15 300 3 440 6 300
488508 208FFSG 40 1.5748 80 3.1496 21 .827 27 1.063 27 1.063 1.0 .040 1 320 2.05 29 100 6 540 18 000 4 050 5 600
1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2)
Listed values are for pressed steel or polyamide cage, ABEC-1.
The values have been determined through historical application and practice. For a more complete explanation, see page 274.
3)
Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
4) Add suffix “V” when snap ring is on seal side.
225
Felt Seal Replacement Bearings
Interchange MRC Bearing Services
MRC Felt Seal Replacement Bearings have synthetic rubber seals.
226
227
Industrial Truck Mast Guide Bearings MRC Bearing Services
Basic Interchange
MRC
Bearing
Number SKF BCA Hoover/NSK McGill NDH Split
204SZZ271 BNTB316574 — — — — —
205SZZ29 — — — — — —
207SZZ201 — — — — — —
207SZZ31 — — — — — —
307SZZ191 — — — — — —
308SZZ41 — — — — — —
308SZZ51 362480 EX4989 — BB1747 — —
308SZZ61 — — — — — —
309SZZ1 — MG309DD — BB850 — —
309SZZ4 — MG309DDA X501RS BB1652 ZMG609XRY1Z8 —
309SZZ51 — — — — — —
309SZZ91 — — — — — —
309SZZ121 — — — — — —
311SZZ1 — — — BB16493 — —
311SZZ21 — — — — — —
311SZZ51 — — — — — —
1)
Check availability before designing into new equipment.
228
Mast Guide Bearings
229
Mast Guide Bearings MRC Bearing Services
Knickerbocker Co.
4774102 5108-BZZ-1 371202 307-SZZ-18
Clark Equipment
4797550 5209-BZZ-1
4798050 5210-BZZ-1 30451 307-SZZ-10
4803599 5109-BZZ-2 342957 307-SZZ-10 30487 305-SZZ-3
4803665 5109-BZZ-1 665619 208-SZZ-9 30719 309-SZZ-4
Massey Ferguson
4812920 307-SZZ-9 738752-J 309-SZZ-1
4817265 207-SZZ-20 746623 305-SZZ-3
4820659 309-SZZ-4 746624 307-SZZ-10
4832744 311-SZZ-2 311-SZZ-1 311-SZZ-1
996829 307-SZZ-10
4842106 5209-BZZ-2 672896M1 309-SZZ-1
Pettibone Corporation
1654614 309-SZZ-4
4859065 5109-BZZ-3 1695854 306-SZZ-5
4863104 5309-RZZ-1 1697663 311-SZZ-1
48206693 309-SZZ-4 31486 206-SZZ-16
1764714 5316-SZZ-1
71005603 309-SZZ-4 F11201 307-SZZ-10
2306335 307-SZZ-11
Pettibone-Mercury
8612154 311-SZZ-5
Petti-Mulliken
307-SZZ-10 307-SZZ-10 2359446 5309-BZZ-2
309-SZZ-4 309-SZZ-4 2359447 5307-BZZ-1
Raymond
35A11111 307-SZZ-8 205-SZZ-29 205-SZZ-29
305-SZZ-3 305-SZZ-3 305-SZZ-6 305-SZZ-6
306-SZZ-5 306-SZZ-5 309-SZZ-4 309-SZZ-4
Crown Controls
307-SZZ-10 307-SZZ-10 449033 309-SZZ-4
Schreck
309-SZZ-1 309-SZZ-1
309-SZZ-4 309-SZZ-4 74020-B 305-SZZ-3
5108-BZZ-1 5108-BZZ-1 31-42014 307-SZZ-10
74668-1 307-SZZ-10
5208-BTZ-1 5208-BTZ-1 31-42015 309-SZZ-4
79943 309-SZZ-4
Dyna-Power Corporation
185531 208-SZZ-16 31-43450 305-SZZ-3
Towmotor Corporation
102916 206-SZZ-16 260100-18-001-00 307-SZZ-16 See Caterpillar Tractor
Fiat-Allis
104744 309-SZZ-4
White Farm Equipment
105475 306-SZZ-5
105476 204-SZZ-20 74820659 309-SZZ-4
120891 307-SZZ-10 74832744 311-SZZ-2 20-3004059 309-SZZ-5
230
Wide Inner Ring
Medium Series
300SWI Non-Filling Notch Type 300WI Filling Notch Type To determine bearing life, refer to page 52 for SWI, and page 62 for WI.
305SWI 25 .9843 62 2.4409 17 .6693 25.4 1 38.1 1.499 1.0 .04 850 1.32 20 800 4 680 11 200 2 520 11 000 14 000
306SWI 30 1.1811 72 2.8346 19 .7480 30.16 1³|₁₆ 43.1 1.698 1.0 .04 1 290 2.00 29 600 6 650 16 600 3 730 9 000 11 000
307SWI 35 1.3780 80 3.1496 21 .8268 34.93 1³|₈ 48.7 1.917 1.5 .06 1 630 2.53 36 400 8 180 20 800 4 680 8 500 10 000
309SWI 45 1.7717 100 3.9370 25 .9843 39.69 1⁹|₁₆ 61.1 2.405 1.5 .06 2 440 3.78 52 700 11 900 31 500 7 080 6 700 8 000
310SWI 50 1.9685 110 4.3307 27 1.0630 44.45 1³|₄ 67.5 2.659 2.0 .08 2 900 4.50 61 800 13 900 38 000 8 540 6 300 7 500
311SWI 55 2.1654 120 4.7244 29 1.1417 49.21 1¹⁵|₁₆ 74.0 2.915 2.0 .08 3 410 5.28 71 500 16 100 45 000 10 100 5 600 6 700
313SWI 65 2.5591 140 5.5118 33 1.2992 58.74 2⁵|₁₆ 85.1 3.350 2.0 .08 4 540 7.03 92 300 20 800 60 000 13 500 4 800 5 600
315SWI 75 2.9528 160 6.2992 37 1.4567 68.26 2¹¹|₁₆ 98.9 3.895 2.0 .08 6 530 10.1 121 000 27 200 85 000 19 100 4 300 5 000
318SWI 90 3.5433 190 7.4803 43 1.6929 73.03 2⁷|₈ 121 4.750 2.5 .10 7 280 11.3 133 000 29 900 98 000 22 000 3 400 4 000
320SWI 100 3.9370 215 8.4646 47 1.8504 82.55 3¹|₄ 132 5.210 2.5 .10 11 600 18.0 182 000 40 900 150 000 33 700 3 000 3 600
308WI4) 40 1.5748 90 3.5433 23 .9055 36.51 1⁷|₁₆ 54.8 2.159 1.5 .06 2 770 4.30 46 800 10 500 36 000 8 090 6 200 7 500
311WI 55 2.1654 120 4.7244 29 1.1417 44.45 1³|₄ 72.7 2.863 2.0 .08 4 690 7.26 74 800 16 800 61 000 13 700 4 600 5 600
312WI4) 60 2.3622 130 5.1181 31 1.2205 53.98 2¹|₈ 79.1 3.114 2.0 .08 5 430 8.42 91 300 20 500 78 000 17 500 4 300 5 300
314WI4) 70 2.7559 150 5.9055 35 1.3780 63.50 2¹|₂ 94.5 3.719 2.0 .08 7 740 12.0 114 000 25 600 102 000 22 900 3 700 4 500
315WI4) 75 2.9528 160 6.2992 37 1.4567 68.26 2¹¹|₁₆ 101 3.976 2.0 .08 8 740 13.6 125 000 28 000 116 000 26 000 3 500 4 300
316WI4) 80 3.1496 170 6.6929 39 1.5354 68.26 2¹¹|₁₆ 109 4.282 2.0 .08 9 470 14.7 138 000 31 000 129 000 29 000 3 300 4 000
318WI4) 90 3.5433 190 7.4803 43 1.6929 73.03 2⁷|₈ 121 4.750 2.5 .10 12 100 18.8 157 000 35 300 160 000 36 000 2 800 3 400
1)
Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.
2) Listed
values are for pressed steel or polyamide cage, ABEC-1.
The values have been determined through historical application and practice. For a more complete explanation, see page 274.
3)
Rating for one million revolutions or 500 hours at 33¹|₃ RPM.
4) Check availability before designing into new equipment.
231
232
BEARING
INTRODUCTION ENGINEERING DATA MARATHON SERIES MADE-TO-ORDER
SPECIFICATION TABLES
Engineering Data
Section III
Engineering Data
Speed Ratings.............................................................................................................................274
Materials and Limitations ............................................................................................................277
Lubrication ..................................................................................................................................281
Vibration Data..............................................................................................................................299
233
Duplex Bearings MRC Bearing Services
An MRC duplex bearing is specifically manufactured
with a controlled relationship between the axial
location of the inner and outer ring faces. Duplex
bearings are ordinarily supplied as half pairs unless
they are high precision machine tool bearings that DF—Face-to-face
typically come in pairs. Combinations of three or
more bearings are also available. This sketch shows the face-to-face (DF) position,
where the two halves are placed so that the contact
MRC duplex bearings may be used to advantage in angle lines of the two bearings are converging
applications where: inwardly. For all MRC duplex bearings, this means
1. Axial and radial deflections must be held to that the unmarked faces of the outer rings are
a minimum; together. On all angular contact and Type R bearings,
2. Maximum radial capacity is required; the low shoulder sides of the outer rings will be
3. Heavy single direction or reversing thrust adjacent.
loads must be supported;
4. Axial shaft location must be maintained The DF position may be used to advantage where
under reversing thrust loads; and the duplex pair carries: (1) a heavy radial load; (2)
5. Moment loading is present. a combined radial and thrust load; (3) a reversing
DT—Tandem
234
Duplex Bearings
Special Methods of Mounting
The three methods of mounting duplex pairs—DB,
DF, and DT—are basic. However, other combinations
may frequently be used to advantage. A few of these
combinations are shown below.
An arrangement such as this will provide extremely Type DU bearings have flush ground faces and when
high load-carrying capacity in the direction of the mounted in pairs and clamped, have neither preload
heavy outer ring shoulder of the two tandem mounted nor end play.
bearings as well as considerable reversing thrust. If
the thrust load in both directions is equal in Type DS bearings are furnished with preload and are
magnitude and duration, an arrangement of four also identified on the bearing with the designation DL,
bearings could be used in which a DT pair would be DM, DH or DX for light, medium, heavy, or special
mounted in DB relationship to another DT pair. The preload respectively.
set would have the suffix DTDB.
Type DE bearings are furnished with end play as
clamped and are also identified on the bearing with
the designation CA, CB, CC or CX for specific end
play values with CX calling for special end play.
235
Duplex Bearings MRC Bearing Services
Interchangeability
Before Clamping
from any other box unless the markings on both
boxes are identical.
236
Duplex Bearings
The 97000U Series consists of a matched set of Caution: To obtain proper load distribution, it is
9000UDT (split inner ring) and 7000DT flush ground necessary to orient mating bearing ring faces,
bearings having a 29° contact angle. The 97000UP and the inner ring halves of the split ring bearing
Series consists of a matched set of 9000UPDT (9000UDT), according to the illustration below. The
(split inner ring) and 7000PDT flush ground counterbored outer ring bearing (7000DT) can be
bearings having a 40° contact angle. mounted either at side (A) or side (B) of the split ring
bearing as shown.
Typical Mountings
In addition, each bearing in the set will be marked
The bearings are usually mounted in pairs. This with a ‘‘V’’ etched on the outer ring surface with the
arrangement divides the thrust load in one direction apex pointing in the main shaft thrust direction.
while accommodating reversing thrust load. To
increase thrust capacity in one direction it is possible
to mount additional bearings in tandem. The number
of bearings in the set will be identified by a number
at the end of the bearing designation. For example,
a set of three bearings (triplex) is identified as the
97000U3 and a set of four (quadruplex) as the
97000U4. Numbers 2 through 9 only will apply.
Numbers 10 and higher indicate some special
characteristic. Illustration of typical mountings are
shown below.
Notes: The numbers ‘‘1’’ and ‘‘2’’ marked on the bearing with the split inner ring, are
to keep the proper relationship between the inner rings and the outer ring.
The counterbore bearing(s) can be mounted either side (A) or (B) (above or below)
the split bearing provided that the ‘‘V’’’s marked on the O.D. of bearings are pointed in
the direction of the ‘‘Primary Shaft Thrust’’.
237
238
ABEC 1 ABMA/ISO Tolerances for Single-Row,
Double-Row, and Duplex Bearings
Tolerances in inches (shaded) and millimeters.
Inner Ring
Bore Over 2.5 10 18 30 50 80 120 150 180
Diameter (mm) Incl 10 18 30 50 80 120 150 180 250
Bore +.0000 –.0003 –.0003 –.0004 –.00045 –.0006 –.0008 –.0010 –.0010 –.0012
Diameter –.008 –.008 –.010 –.012 –.015 –.020 –.025 –.025 –.030
Bore 1800, 1900 .0004 .0004 .0005 .0006 .00075 .0010 .0012 .0012 .0015
Out–of–Round Series
.010 .010 .013 .015 .019 .025 .031 .031 .038
(Max)
100 .0003 .0003 .0004 .00045 .00075 .0010 .0012 .0012 .0015
Series
.008 .008 .010 .012 .019 .025 .031 .031 .038
200 300 .00025 .00025 .0003 .00035 .00045 .0006 .00075 .00075 .0009
400 Series
.006 .006 .008 .009 .011 .015 .019 .019 .023
Radial Runout .0004 .0004 .0005 .0006 .0008 .0010 .0012 .0012 .0016
(Max) .010 .010 .013 .015 .020 .025 .030 .030 .040
Width Variation .0006 .0008 .0008 .0008 .0010 .0010 .0012 .0012 .0012
(Max) .015 .020 .020 .020 .025 .025 .030 .030 .030
Side Runout With .0008 .0008 .0008 .0008 .0010 .0010 .0012 .0012 .0012
Bore (Max) .020 .020 .020 .020 .025 .025 .030 .030 .030
Raceway Runout .0008 .0008 .0008 .0008 .0010 .0010 .0012 .0012 .0016
With Side (Max) .020 .020 .020 .020 .025 .025 .030 .030 .040
Ring Width +.0000 –.0047 –.0047 –.0047 –.0047 –.0059 –.0079 –.0098 –.0098 –.0118
Single Bearing –.120 –.120 –.120 –.120 –.150 –.200 –.250 –.250 –.300
Ring Width +.0000 –.0098 –.0098 –.0098 –.0098 –.0150 –.0150 –.0197 –.0197 –.0197
Duplex Bearing –.250 –.250 –.250 –.250 –.380 –.380 –.500 –.500 –.500
Outer Ring
Outside Over 6 18 30 50 80 120 150 180 250 315
Diameter (mm) Incl 18 30 50 80 120 150 180 250 315 400
Outside +.0000 –.0003 –.00035 –.00045 –.0005 –.0006 –.0007 –.0010 –.0012 –.0014 –.0016
Diameter –.008 –.009 –.011 –.013 –.015 –.018 –.025 –.030 –.035 –.040
Outside Diameter 1800, 1900 .0004 .00045 .00055 .00065 .00075 .0009 .0012 .0015 .0017 .0020
Out–of–Round Series
.010 .012 .014 .016 .019 .023 .031 .038 .044 .050
(Max)
100 .0003 .00035 .00045 .0005 .00075 .0009 .0012 .0015 .0017 .0020
Series
.008 .009 .011 .013 .019 .023 .031 .038 .044 .050
200 300 .00025 .0003 .0003 .0004 .00045 .00055 .00075 .0009 .0010 .0012
400 Series
.006 .007 .008 .010 .011 .014 .019 .023 .026 .030
Width Variation
(Max) Identical to Inner Ring of Same Bearing
O.D. Runout With .0008 .0008 .0008 .0010 .0010 .0012 .0012 .0012 .0014 .0016
Side (Max) .020 .020 .020 .025 .025 .030 .030 .030 .035 .040
Raceway Runout .0012 .0012 .0012 .0012 .0014 .0016 .0020 .0024 .0028 .0031
With Side (Max) .030 .030 .030 .030 .035 .040 .050 .060 .070 .080
Ring Width
SingleBearing
Identical to Inner Ring of Same Bearing
Ring Width
Duplex Bearing
*No values established for 1800 and 1900 series.
239
ABEC 3 ABMA/ISO Tolerances for Single-Row,
Double-Row, and Duplex Bearings MRC Bearing Services
Tolerances in inches (shaded) and millimeters.
Inner Ring
Bore Over 2.5 10 18 30 50 80 120 150 180
Diameter (mm) Incl 10 18 30 50 80 120 150 180 250
Bore +.0000 –.0003 –.0003 –.0003 –.00045 –.0005 –.0006 –.0007 –.0007 –.00085
Diameter –.007 –.007 –.008 –.010 –.012 –.015 –.018 –.018 –.022
Bore 1800, 1900 .00035 .00035 .0004 .0005 .0006 .00075 .0009 .0009 .0011
Out–of–Round Series
(Max) .009 .009 .010 .013 .015 .019 .023 .023 .028
100 .0003 .0003 .0003 .0004 .0006 .00075 .0009 .0009 .0011
Series
.007 .007 .008 .010 .015 .019 .023 .023 .028
200 300 .0002 .0002 .00025 .0003 .00035 .00045 .00055 .00055 .00065
400 Series
.005 .005 .006 .008 .009 .011 .014 .014 .017
Radial Runout .00025 .0003 .0003 .0004 .0004 .0005 .0007 .0007 .0008
(Max) .006 .007 .008 .010 .010 .013 .018 .018 .020
Width Variation .0006 .0008 .0008 .0008 .0010 .0010 .0012 .0012 .0012
(Max) .015 .020 .020 .020 .025 .025 .030 .030 .030
Side Runout With .0004 .0004 .0004 .0004 .0005 .0005 .0006 .0006 .0006
Bore (Max) .010 .010 .010 .010 .013 .013 .015 .015 .015
Raceway Runout .0006 .0006 .0006 .0006 .0007 .0007 .0009 .0009 .0009
With Side (Max) .015 .015 .015 .015 .018 .018 .023 .023 .023
Ring Width +.0000 –.0047 –.0047 –.0047 –.0047 –.0059 –.0079 –.0098 –.0098 –.0118
Single Bearing –.120 –.120 –.120 –.120 –.150 –.200 –.250 –.250 –.300
Ring Width +.0000 –.0098 –.0098 –.0098 –.0098 –.0150 –.0150 –.0197 –.0197 –.0197
Duplex Bearing –.250 –.250 –.250 –.250 –.380 –.380 –.500 –.500 –.500
Outer Ring
Outside Over 6 18 30 50 80 120 150 180 250 315
Diameter (mm) Incl 18 30 50 80 120 150 180 250 315 400
Outside +.0000 –.0003 –.0003 –.0004 –.0004 –.0005 –.0006 –.0007 –.0008 –.0010 –.0011
Diameter –.007 –.008 –.009 –.011 –.013 –.015 –.018 –.020 –.025 –.028
Outside Diameter 1800, 1900 .0004 .0004 .0004 .0006 .0006 .0007 .0009 .0010 .0012 .0014
Out–of–Round Series
(Max) .009 .010 .011 .014 .016 .019 .023 .025 .031 .035
100 .0003 .0003 .0004 .0004 .0006 .0007 .0009 .0010 .0012 .0014
Series
.007 .008 .009 .011 .016 .019 .023 .025 .031 .035
200 300 .0002 .0002 .0003 .0003 .0004 .0004 .0006 .0006 .0007 .0008
400 Series
.005 .006 .007 .008 .010 .011 .014 .015 .019 .021
Width Variation
(Max) Identical to Inner Ring of Same Bearing
O.D. Runout With .0004 .0004 .0004 .0005 .0005 .0006 .0006 .0006 .0007 .0008
Side (Max) .010 .010 .010 .013 .013 .015 .015 .015 .018 .020
Raceway Runout .0008 .0008 .0008 .0008 .0009 .0010 .0012 .0014 .0016 .0018
With Side (Max) .020 .020 .020 .020 .023 .025 .030 .035 .040 .045
Ring Width
SingleBearing
Identical to Inner Ring of Same Bearing
Ring Width
Duplex Bearing
*No values established for 1800 and 1900 series.
240
ABEC 5 ABMA/ISO Tolerances for Single-Row,
Double-Row, and Duplex Bearings
Tolerances in inches (shaded) and millimeters.
Inner Ring
Bore Over 2.5 10 18 30 50 80 120 150 180
Diameter (mm) Incl 10 18 30 50 80 120 150 180 250
Bore + .0000 –.0002 –.0002 –.00025 –.0003 –.00035 –.0004 –.0005 –.0005 –.0006
Diameter –.005 –.005 –.006 –.008 –.009 –.010 –.013 –.013 –.015
Bore 1800, 1900 .0002 .0002 .00025 .0003 .00035 .0004 .0005 .0005 .0006
Out–of–Round Series
(Max) .005 .005 .006 .008 .009 .010 .013 .013 .015
100, 200, 300 .00015 .00015 .0002 .00025 .0003 .0003 .0004 .0004 .00045
400 Series
.004 .004 .005 .006 .007 .008 .010 .010 .012
Radial Runout .00015 .00015 .00015 .0002 .0002 .00025 .0003 .0003 .0004
(Max) .004 .004 .004 .005 .005 .006 .008 .008 .010
Width Variation .0002 .0002 .0002 .0002 .00025 .0003 .0003 .0003 .0004
(Max) .005 .005 .005 .005 .006 .007 .008 .008 .010
Side Runout With .0003 .0003 .0003 .0003 .0003 .00035 .0004 .0004 .00045
Bore (Max) .007 .007 .008 .008 .008 .009 .010 .010 .011
Raceway Runout .0003 .0003 .0003 .0003 .0003 .00035 .0004 .0004 .0005
With Side (Max) .007 .007 .008 .008 .008 .009 .010 .010 .013
Ring Width +.0000 –.0016 –.0031 –.0047 –.0047 –.0059 –.0079 –.0098 –.0098 –.0118
Single Bearing –.040 –.080 –.120 –.120 –.150 –.200 –.250 –.250 –.300
Ring Width + .0000 –.0098 –.0098 –.0098 –.0098 –.0098 –.0150 –.0150 –.0150 –.0197
Duplex Bearing –.250 –.250 –.250 –.250 –.250 –.380 –.380 –.380 –.500
Outer Ring
Outside Over 6 18 30 50 80 120 150 180 250 315
Diameter (mm) Incl 18 30 50 80 120 150 180 250 315 400
Outside +.0000 –.0002 –.00025 –.0003 –.00035 –.0004 –.00045 –.0005 –.0006 –.0007 –.0008
Diameter –.005 –.006 –.007 –.009 –.010 –.011 –.013 –.015 –.018 –.020
Outside Diameter 1800, 1900 .0002 .00025 .0003 .00035 .0004 .00045 .0005 .0006 .0007 .0008
Out–of–Round Series
(Max) .005 .006 .007 .009 .010 .011 .013 .015 .018 .020
100, 200, 300 .00015 .0002 .0002 .0003 .0003 .0003 .0004 .00045 .00055 .0006
400 Series
.004 .005 .005 .007 .008 .008 .010 .011 .014 .015
Radial Runout .0002 .00025 .0003 .0003 .0004 .00045 .0005 .0006 .0007 .0008
(Max) .005 .006 .007 .008 .010 .011 .013 .015 .018 .020
Width Variation
(Max) Identical to Inner Ring of Same Bearing
O.D. Runout With .0003 .0003 .0003 .0003 .00035 .0004 .0004 .00045 .0005 .0005
Side (Max) .008 .008 .008 .008 .009 .010 .010 .011 .013 .013
Raceway Runout .0003 .0003 .0003 .0004 .00045 .0005 .00055 .0006 .0007 .0008
With Side (Max) .008 .008 .008 .010 .011 .013 .014 .015 .018 .020
Ring Width
SingleBearing
Identical to Inner Ring of Same Bearing
Ring Width
Duplex Bearing
241
ABEC 7 ABMA/ISO Tolerances for Single-Row,
Double-Row, and Duplex Bearings MRC Bearing Services
Tolerances in inches (shaded) and millimeters.
Inner Ring
Bore Over 2.5 10 18 30 50 80 120 150 180
Diameter (mm) Incl 10 18 30 50 80 120 150 180 250
Bore + .0000 –.00015 –.00015 –.0002 –.00025 –.0003 –.0003 –.0004 –.0004 –.00045
Diameter –.004 –.004 –.005 –.006 –.007 –.008 –.010 –.010 –.012
Bore 1800, 1900 .0015 .00015 .0002 .00025 .0003 .0003 .0004 .0004 .00045
Out–of–Round Series
(Max) .004 .004 .005 .006 .007 .008 .010 .010 .012
100, 200, 300 .0001 .0001 .00015 .0002 .0002 .00025 .0003 .0003 .00035
400 Series
.003 .003 .004 .005 .005 .006 .008 .008 .009
Radial Runout .0001 .0001 .0001 .00015 .00015 .0002 .00025 .00025 .0003
(Max) .0025 .0025 .003 .004 .004 .005 .006 .006 .008
Width Variation .0001 .0001 .0001 .0001 .00015 .00015 .0002 .0002 .00025
(Max) .0025 .0025 .0025 .003 .004 .004 .005 .005 .006
Side Runout With .0001 .0001 .00015 .00015 .0002 .0002 .00025 .00025 .0003
Bore (Max) .003 .003 .004 .004 .005 .005 .006 .006 .007
Raceway Runout .0001 .0001 .00015 .00015 .0002 .0002 .0003 .0003 .0003
With Side (Max) .003 .003 .004 .004 .005 .005 .007 .007 .008
Ring Width +.0000 –.0016 –.0031 –.0047 –.0047 –.0059 –.0079 –.0098 –.0098 –.0118
Single Bearing –.040 –.080 –.120 –.120 –.150 –.200 –.250 –.250 –.300
Ring Width + .0000 –.0098 –.0098 –.008 –.0098 –.0098 –.0150 –.0150 –.0150 –.0197
Duplex Bearing –.250 –.250 –.250 –.250 –.250 –.380 –.380 –.380 –.500
Outer Ring
Outside Over 6 18 30 50 80 120 150 180 250 315
Diameter (mm) Incl 18 30 50 80 120 150 180 250 315 400
Outside +.0000 –.00015 –.0002 –.00025 –.0003 –.0003 –.00035 –.0004 –.00045 –.0005 –.0006
Diameter –.004 –.005 –.006 –.007 –.008 –.009 –.010 –.011 –.013 –.015
Outside Diameter 1800, 1900 .00015 .0002 .00025 .0003 .0003 .00035 .0004 .00045 .0005 .0006
Out–of–Round Series
(Max) .004 .005 .006 .007 .008 .009 .010 .011 .013 .015
100, 200, 300 .0001 .00015 .0002 .0002 .00025 .0003 .0003 .0003 .0004 .00045
400 Series
.003 .004 .005 .005 .006 .007 .008 .008 .010 .011
Radial Runout .0001 .00015 .0002 .0002 .00025 .0003 .0003 .0004 .00045 .0005
(Max) .003 .004 .005 .005 .006 .007 .008 .010 .011 .013
Width Variation
(Max) Identical to Inner Ring of Same Bearing
O.D. Runout With .00015 .00015 .00015 .00015 .0002 .0002 .0002 .0003 .0003 .0004
Side (Max) .004 .004 .004 .004 .005 .005 .005 .007 .008 .010
Raceway Runout .0002 .0002 .0002 .0002 .00025 .0003 .0003 .0004 .0004 .0005
With Side (Max) .005 .005 .005 .005 .006 .007 .008 .010 .010 .013
Ring Width
SingleBearing
Identical to Inner Ring of Same Bearing
Ring Width
Duplex Bearing
242
ABEC 9 ABMA/ISO Tolerances for Single-Row,
Double-Row, and Duplex Bearings
Tolerances in inches (shaded) and millimeters.
Inner Ring
Bore Over 2.5 10 18 30 50 80 120 150 180
Diameter (mm) Incl 10 18 30 50 80 120 150 180 250
Bore + .0000 –.0001 –.0001 –.0001 –.0001 –.00015 –.0002 –.0003 –.0003 –.0003
Diameter –.0025 –.0025 –.0025 –.0025 –.004 –.005 –.007 –.007 –.008
Bore Out–of–Round .0001 .0001 .0001 .0001 .0015 .0002 .0003 .0003 .0003
(Max) .0025 .0025 .0025 .0025 .004 .005 .007 .007 .008
Radial Runout .00005 .00005 .0001 .0001 .0001 .0001 .0001 .0002 .0002
(Max) .0015 .0015 .0025 .0025 .0025 .0025 .0025 .005 .005
Width Variation .00005 .00005 .00005 .00005 .00005 .0001 .0001 .00015 .0002
(Max) .0015 .0015 .0015 .0015 .0015 .0025 .0025 .004 .005
Side Runout With .00005 .00005 .00005 .00005 .00005 .0001 .0001 .00015 .0002
Bore (Max) .0015 .0015 .0015 .0015 .0015 .0025 .0025 .004 .005
Raceway Runout .00005 .00005 .0001 .0001 .0001 .0001 .0001 .0002 .0002
With Side (Max) .0015 .0015 .0025 .0025 .0025 .0025 .0025 .005 .005
Ring Width +.0000 –.0016 –.0031 –.0047 –.0047 –.0059 –.0079 –.0098 –.0118 –.0138
Single Bearing –.040 –.080 –.120 –.120 –.150 –.200 –.250 –.300 –.350
Ring Width + .0000 –.0098 –.0098 –.0098 –.0098 –.0098 –.0150 –.0150 –.0197 –.0197
Duplex Bearing –.250 –.250 –.250 –.250 –.250 –.380 –.380 –.500 –.500
Outer Ring
Outside Over 6 18 30 50 80 120 150 180 250 315
Diameter (mm) Incl 18 30 50 80 120 150 180 250 315 400
Outside +.0000 –.0001 –.00015 –.00015 –.00015 –.0002 –.0002 –.0003 –.0003 –.0003 –.0004
Diameter –.0025 –.004 –.004 –.004 –.005 –.005 –.007 –.008 –.008 –.010
Outside Diameter .0001 .00015 .00015 .00015 .0002 .0002 .0003 .0003 .0003 .0004
Out–of–Round (Max) .0025 .004 .004 .004 .005 .005 .007 .008 .008 .010
Radial Runout .00005 .0001 .0001 .00015 .0002 .0002 .0002 .0003 .0003 .0005
(Max) .0015 .0025 .0025 .004 .005 .005 .005 .007 .007 .008
Width Variation
(Max) Identical to Inner Ring of Same Bearing
O.D. Runout With .00005 .00005 .00005 .00005 .0001 .0001 .0001 .00015 .0002 .0003
Side (Max) .0015 .0015 .0015 .0015 .0025 .0025 .0025 .004 .005 .007
Raceway Runout .00005 .0001 .0001 .00015 .0002 .0002 .0002 .0003 .0003 .0003
With Side (Max) .0015 .0025 .0025 .004 .005 .005 .005 .007 .007 .008
Ring Width
SingleBearing
Identical to Inner Ring of Same Bearing
Ring Width
Duplex Bearing
243
244
Shaft and Housing Fits
245
Shaft and Housing Fits MRC Bearing Services
Radial Location of Bearings
If the load carrying ability of a bearing is to be fully When a stationary load exists, a bearing ring will not
utilized, its rings or washers must be supported around normally turn on its seating. Therefore, the ring need not
their complete circumference and across the whole necessarily have an interference fit unless this is
width of the raceway. The support must be firm and required for other reasons.
even and, for inner rings, can be provided by a
cylindrical or tapered seating or, for washers, by a flat When the direction of load is indeterminate and
(plane) support surface. This means that the seatings particularly where heavy loads are involved, it is
must be made with adequate accuracy and that they desirable that both rings have an interference fit. For the
have a surface which is uninterrupted by grooves, holes inner ring the fit recommended for rotating load is
or other features. In addition the rings must be reliably normally used. However, when the outer ring must be
secured to prevent them from turning on or in their free to move axially in the housing and the load is not
seatings under load. Inadequately or incorrectly secured heavy, a somewhat looser fit than that recommended for
bearing rings generally produce damage to the rotating load may be used. When interference fits are
bearings and associated components. used on both the inner ring and outer ring, the remaining
internal clearance of the bearing should be considered
A satisfactory radial location and an adequate support to avoid excessive clearance reduction, i.e. internal
can generally only be obtained when the rings are preloading.
mounted with an appropriate° of interference. However,
when simple mounting and dismounting are desirable, 2. Magnitude of the load.
or when axial displacement is required with a non-
locating bearing, interference fits cannot be used. The interference fit of a bearing inner ring on its seating
will be loosened with increasing load as the ring will
Selection of fit expand. Under the influence of rotating load the ring
When selecting a fit, the factors discussed in the may begin to creep. The° of interference must therefore
following and the general guidelines in respect of them be related to the magnitude of the load: the heavier the
should be considered. load, particularly if it is of shock character, the greater
the interference required.
1. Conditions of rotation
3. Bearing internal clearance
Conditions of rotation refer to the movement of the
bearing ring being considered in relation to the direction An interference fit of a bearing on the shaft or in the
of the load. Essentially there are three different housing means that the ring is elastically deformed
conditions: ‘‘rotating load’’ ‘‘stationary load’’ and (expanded or compressed) and the bearing internal
‘‘direction of load indeterminate’’. clearance reduced. A certain minimum clearance
should remain, however (see also ‘‘Bearing radial
If the bearing ring rotates and the load is stationary, clearance’’, page 270). The initial clearance and
or if the ring is stationary and the load rotates so that permissible reduction depend on the type and size of
all points on the raceway are subjected to load in the the bearing. The reduction in clearance due to the
course of one revolution, the load is defined as a interference fit can be so large that bearings with
‘‘rotating load’’. Heavy loads which do not rotate but increased radial clearance have to be used in order to
oscillate (for example, those acting on the outer rings prevent the bearing from becoming preloaded.
of connecting rod bearings) are generally considered
as rotating loads. 4. Temperature conditions
‘‘Stationary load’’ applies if the bearing ring is stationary In service, bearing rings normally reach a temperature
and the load is also stationary, or if the ring and load which is higher than that of the components to which
rotate at the same speed so that the load is always they are fitted. This can result in an easing of the fit of
directed to the same point on the raceway. the inner ring on its seating, while outer ring expansion
may prevent the desired axial displacement of the ring
Variable external loads, shock loads, vibrations and
in its housing. Temperature differentials and the direction
unbalance loads in high-speed machines give rise to
of heat flow must therefore be carefully considered.
changes in the direction of load which cannot be
accurately described. Such conditions are classified as 5. Running accuracy requirements
‘‘direction of load indeterminate’’.
To reduce resilience and vibration, clearance fits should
A bearing ring subjected to a rotating load will turn generally not be used for bearings where high demands
(creep) on its own seating if mounted with a clearance are placed on running accuracy. Bearing seatings on
fit, and wear (fretting corrosion) of the contacting the shaft and in the housing should be made to narrow
surfaces will occur. To prevent this, interference fits must
be used. The° of interference needed is dictated by the
operating conditions (see points 2 and 4).
246
Shaft and Housing Fits
made to narrow dimensional tolerances, Bearings with clearance fits are usually easier to
corresponding at least to ABEC-5 for the shaft and mount or dismount than those with interference fits.
ABEC-3 for the housing as shown in the tables. Where operating conditions necessitate interference
fits and it is essential that mounting and dismounting
6. Design and material of shaft and housing can be done easily, separable bearings, or bearings
with tapered bore and adapter or withdrawal sleeve
CAUTION: The fit of a bearing ring on its seating may be used.
must not lead to uneven distortion of the ring
(out-of- round). This can be caused for example by 8. Displacement of non-locating bearing
discontinuities in the seating surface. Split housings
are therefore not generally suitable where outer rings If non-separable bearings are used as non-locating
are to have an interference fit. bearings it is imperative that one of the bearing rings
is free to move axially at all times during operation.
To ensure adequate support for bearing rings This is ensured by adopting a clearance fit for that
mounted in thin-walled housings, light alloy housings ring which carries a stationary load. When the outer
or on hollow shafts, heavier interference fits than ring is under stationary load so that axial
those normally selected for thick-walled steel or cast displacement has to take place in the housing bore, a
iron housings or for solid shafts should be used (see hardened intermediate bushing is often fitted to the
also ‘‘Fits for hollow shafts’’, page 248). outer ring, for example, where light alloy housings are
employed. In this way a ‘‘hammering out’’ of the
For stainless steel shafts, reduced shaft interference housing seating because of the lower material
or increased bearing internal clearance should be hardness is avoided; it would otherwise result in the
considered because of the high coefficient of axial displacement being restricted or even
expansion of stainless steel. impossible after a time. If cylindrical or needle roller
bearings having one ring without flanges are used,
both bearing rings may be mounted with an
interference fit because axial displacement will take
place within the bearing.
247
Shaft and Housing Fits MRC Bearing Services
Recommended Fits different shaft materials are being used, MRC Application
Engineering should be contacted in order to select more
The general recommendation for shaft and housing
appropriate fit tolerances.
diameters and resulting fits are shown in the tables on
pages 250-261, for ABEC-1, 3, 5, and 7 tolerance grades Tapered Bore Bearings
and either rotating or stationary shaft or housing. They apply
to single-row, double-row and duplex bearings mounted on Bearings with tapered bores are mounted either on tapered
steel shafts and in steel or cast iron housings. For special shafts or on slotted sleeves having an external taper and
bearing applications and arrangements, other fits may be mounted on cylindrical shafts. In these cases, the fit of the
required as shown in the tables on pages 263-270. inner ring is not determined by the selected shaft tolerance
but by the distance through which the ring is driven up on
Duplex Bearings the tapered shaft or sleeve. Special precautions with
MRC 7000PJ series, 40° contact angle, bearings are respect to reduction in internal clearance must be
supplied in several different clearance/preload classes. observed. For the recommended mounting procedure refer
These bearings are identified with additional suffix letters of to pages 80 and 81 in the self-aligning ball bearing section.
either DE, DU, or DS for endplay, free-running no endplay, Fits For Hollow Shafts
or preload respectively. The PJDE suffix would indicate
a bearing specifically designed for paired mounting and If bearings are to be mounted with an interference fit on a
axial endplay or looseness. The “DE” clearance class, hollow shaft it is generally necessary to use a heavier
without any additional suffix code letters is equivalent to interference fit than that used for a solid shaft in order to
a “CB” clearance range (see table below). However, the achieve the same surface pressure between the inner ring
“DE” clearance class can also specify other clearance and shaft seating. The following diameter ratios are
ranges if an additional 4-digit suffix code follows the “DE”. important when deciding on the fit to be used:
The other ranges include the “CA”, “CC”, and “CX” ranges
di d
which will be marked on the bearing box. ci = and ce =
d de
Bore
“CB” End Play Per Set where
Diameter Min. Max. ci = diameter ratio of hollow shaft
(mm) ce = diameter ratio of inner ring
,001 ,0001 ,001 ,0001
Over Incl mm inch mm inch d = outside diameter of hollow shaft ( = bore diameter of
— 10 14 6 22 9 bearing)
10 18 15 6 23 9
18 30 18 7 26 10 di = internal diameter of hollow shaft
30 50 22 9 30 12 de = mean outside diameter of inner ring
50 80 26 10 38 15
80 120 32 13 44 17
120 180 35 14 47 19 The fit is not appreciably affected until the diameter ratio of
180 250 45 18 61 24 the hollow shaft ci ≥ 0.5. If the outside diameter of the inner
250 315 52 21 68 27
ring is not known, the diameter ratio ce can be calculated
with sufficient accuracy from the equation
Duplex bearings may also be supplied without axial
clearance and without preload. This range would be d
ce =
considered “free-running” or “no endplay” and is k (D – d) + d
designated by the suffix letters “DU”. Ex. 7200PJDU.
where
Bearings with preload are identified with the suffix letters d = bore diameter of bearing
“DS” on the bearing itself and the bearing box would have D = outside diameter of bearing
an additional marking of either “DL”, “DM”, “DH”, or “DX” k = a factor for the bearing type
and a 4-digit MRC specification code, signifying light, k = 0.25 for self-aligning ball bearings of series 22 and 23
medium, heavy, or special preload respectively. and for cylindrical roller bearings
The normal shaft and housing tolerances for duplexed k = 0.3 for all other bearings
bearings with endplay (DE) are “k5” and “H6” respectively. To determine the requisite interference fit for a bearing to
For the “DU” and “DS” variants, the recommended shaft be mounted on a hollow shaft, use is made of the mean
and housing tolerances are “h5” and “H6” respectively. The probable interference between shaft diameter and bearing
reduced shaft interference resulting from the ISO “h5” fit bore obtained for the tolerance recommended for a solid
minimizes the loss of internal clearance caused by shaft of the same diameter. If the plastic deformation
expansion of the inner ring. Loss of internal clearance (smoothing) of the mating surfaces produced during
changes the bearing preload that can lead to excessive mounting is neglected, then the effective interference can
heating and premature failure. See pages 264 and 267 for be equated to the mean probable interference.
specific tolerance dimensions. These recommendations are
valid for solid steel shafts and cast iron or steel housings. If
248
Shaft and Housing Fits
Example:
A 208S deep groove ball bearing is to be mounted on
a hollow shaft having a diameter ratio of Ci = 0.8. The
recommended mean probable interference for a solid
steel shaft is 0.00055 determined from the tables for
an ABEC-1 grade bearing with a 40mm bore
diameter. 40
For C = 0.8 and C = 0.3 (80 – 40) + 40 = 0.77,
i e
249
Shaft Limits—ABEC-1 MRC Bearing Services
4 4 0.1575 3.992 0.1572 4.006 0.1577 4.001 0.1575 3.996 0.1573 3.988 0.1570
5 5 0.1969 4.992 0.1966 5.006 0.1971 5.001 0.1969 1T 0 4.996 0.1967 4.988 0.1964 12L 5L
6 6 0.2362 5.992 0.2359 6.006 0.2364 6.001 0.2362 14T 5T 5.996 0.2360 5.988 0.2357 4T 1T
7 7 0.2756 6.992 0.2753 7.007 0.2759 7.001 0.2756 6.995 0.2754 6.986 0.2750
8 8 0.3150 7.992 0.3147 8.007 0.3153 8.001 0.3150 1T 0 7.995 0.3148 7.986 0.3144 14L 6L
9 9 0.3543 8.992 0.3540 9.007 0.3546 9.001 0.3543 15T 6T 8.995 0.3541 8.986 0.3537 3T 1T
10 10 0.3937 9.992 0.3934 10.007 0.3940 10.001 0.3937 9.995 0.3935 9.986 0.3931
12 12 0.4724 11.992 0.4721 12.009 0.4728 12.001 0.4724 11.994 0.4722 11.983 0.4717
15 15 0.5906 14.992 0.5903 15.009 0.5910 15.001 0.5906 1T 0 14.994 0.5904 14.983 0.5899 17L 7L
17 17 0.6693 16.992 0.6690 17.009 0.6697 17.001 0.6693 17T 7T 16.994 0.6691 16.983 0.6686 2T 1T
20 20 0.7874 19.990 0.7870 20.011 0.7878 20.002 0.7875 19.993 0.7871 19.980 0.7866
25 25 0.9843 24.990 0.9839 25.011 0.9847 25.002 0.9844 2T 1T 24.993 0.9840 24.980 0.9835 20L 8L
30 30 1.1811 29.990 1.1807 30.011 1.1815 30.002 1.1812 21T 8T 29.993 1.1808 29.980 1.1803 3T 1T
35 35 1.3780 34.987 1.3775 35.013 1.3785 35.002 1.3781 34.991 1.3776 34.975 1.3770
40 40 1.5748 39.987 1.5743 40.013 1.5753 40.002 1.5749 2T 1T 39.991 1.5744 39.975 1.5738 25L 10L
45 45 1.7717 44.987 1.7712 45.013 1.7722 45.002 1.7718 26T 10T 44.991 1.7713 44.975 1.7707 4T 1T
50 50 1.9685 49.987 1.9680 50.013 1.9690 50.002 1.9686 49.991 1.9681 49.975 1.9675
55 55 2.1654 54.985 2.1648 55.015 2.1660 55.002 2.1655 54.990 2.1650 54.971 2.1643
60 60 2.3622 59.985 2.3616 60.015 2.3628 60.002 2.3623 59.990 2.3618 59.971 2.3611
65 65 2.5591 64.985 2.5585 65.015 2.5597 65.002 2.5592 2T 1T 64.990 2.5587 64.971 2.5580 29L 11L
70 70 2.7559 69.985 2.7553 70.015 2.7565 70.002 2.7560 30T 12T 69.990 2.7555 69.971 2.7548 5T 2T
75 75 2.9528 74.985 2.9522 75.015 2.9534 75.002 2.9529 74.990 2.9524 74.971 2.9517
80 80 3.1496 79.985 3.1490 80.015 3.1502 80.002 3.1497 79.990 3.1492 79.971 3.1485
85 85 3.3465 84.980 3.3457 85.018 3.3472 85.003 3.3466 84.988 3.3460 84.966 3.3452
90 90 3.5433 89.980 3.5425 90.018 3.5440 90.003 3.5434 89.988 3.5428 89.966 3.5420
95 95 3.7402 94.980 3.7394 95.018 3.7409 95.003 3.7403 3T 1T 94.988 3.7397 94.966 3.7389 34L 13L
100 100 3.9370 99.980 3.9362 100.018 3.9377 100.003 3.9371 38T 15T 99.988 3.9365 99.966 3.9357 8T 3T
105 105 4.1339 104.980 4.1331 105.018 4.1346 105.003 4.1340 104.988 4.1334 104.966 4.1326
110 110 4.3307 109.980 4.3299 110.018 4.3314 110.003 4.3308 109.988 4.3302 109.966 4.3294
115 115 4.5276 114.980 4.5268 115.018 4.5283 115.003 4.5277 114.988 4.5271 114.966 4.5263
120 120 4.7244 119.980 4.7236 120.018 4.7251 120.003 4.7245 119.988 4.7239 119.966 4.7231
125 125 4.9213 124.975 4.9203 125.021 4.9221 125.003 4.9214 124.986 4.9207 124.961 4.9198
130 130 5.1181 129.975 5.1171 130.021 5.1189 130.003 5.1182 129.986 5.1175 129.961 5.1166
140 140 5.5118 139.975 5.5108 140.021 5.5126 140.003 5.5119 3T 1T 139.986 5.5112 139.961 5.5103 39L 15L
150 150 5.9055 149.975 5.9045 150.021 5.9063 150.003 5.9056 46T 18T 149.986 5.9049 149.961 5.9040 11T 4T
160 160 6.2992 159.975 6.2982 160.021 6.3000 160.003 6.2993 159.986 6.2986 159.961 6.2977
170 170 6.6929 169.975 6.6919 170.021 6.6937 170.003 6.6930 169.986 6.6923 169.961 6.6914
180 180 7.0866 179.975 7.0856 180.021 7.0874 180.003 7.0867 179.986 7.0860 179.961 7.0851
190 190 7.4803 189.970 7.4791 190.024 7.4812 190.004 7.4805 189.985 7.4797 189.956 7.4786
200 200 7.8740 199.970 7.8728 200.024 7.8749 200.004 7.8742 199.985 7.8734 199.956 7.8723
210 210 8.2677 209.970 8.2665 210.024 8.2626 210.004 8.2679 4T 2T 209.985 8.2671 209.956 8.2660 44L 17L
220 220 8.6614 219.970 8.6602 220.024 8.6623 220.004 8.6616 54T 21T 219.985 8.6608 219.956 8.6597 15T 6T
230 230 9.0551 229.970 9.0539 230.024 9.0560 230.004 9.0553 229.985 9.0545 229.956 9.0534
240 240 9.4488 239.970 9.4476 240.024 9.4497 240.004 9.4490 239.985 9.4482 239.956 9.4471
250 250 9.8425 249.970 9.8413 250.024 9.8434 250.004 9.8427 249.985 9.8419 249.956 9.8408
260 260 10.2362 259.965 10.2348 260.027 10.2373 260.004 10.2364 4T 2T 259.983 10.2355 259.951 10.2343 49L 19L
280 280 11.0236 279.965 11.0222 280.027 11.0247 280.004 11.0238 62T 25T 279.983 11.0229 279.951 11.0217 18T 7T
300 300 11.8110 299.965 11.8096 300.027 11.8121 300.004 11.8112 299.983 11.8103 299.951 11.8091
320 320 12.5984 319.960 12.5968 320.029 12.5995 320.004 12.5986 4T 2T 319.982 12.5977 319.946 12.5963 54L 21L
69T 27T 22T 9T
250
Shaft Limits—ABEC-1
R2 3.175 0.1250 3.167 0.1247 3.181 0.1252 3.175 0.1250 0 0 3.171 0.1248 3.163 0.1245 12L 5L
R2A 3.175 0.1250 3.167 0.1247 3.181 0.1252 3.175 0.1250 14T 5T 3.171 0.1248 3.163 0.1245 4T 1T
R3 4.763 0.1875 4.755 0.1872 4.769 0.1877 4.763 0.1875 4.759 0.1873 4.751 0.1870
R4 6.350 0.2500 6.342 0.2497 6.357 0.2503 6.350 0.2500 0 0 6.345 0.2498 6.336 0.2494 14L 6L
R4A 6.350 0.2500 6.342 0.2497 6.357 0.2503 6.350 0.2500 15T 6T 6.345 0.2498 6.336 0.2494 3T 1T
R6 9.525 0.3750 9.517 0.3747 9.532 0.3753 9.525 0.3750 9.520 0.3748 9.511 0.3744
R8 12.700 0.5000 12.692 0.4997 12.709 0.5004 12.700 0.5000 0 0 12.694 0.4998 12.683 0.4993 17L 7L
R10 15.875 0.6250 15.867 0.6247 15.884 0.6254 15.875 0.6250 17T 7T 15.869 0.6248 15.858 0.6243 2T 1T
R12 19.050 0.7500 19.040 0.7496 19.061 0.7504 19.052 0.7501 19.043 0.7497 19.030 0.7492
R14 22.225 0.8750 22.215 0.8746 22.236 0.8754 22.227 0.8751 2T 1T 22.218 0.8747 22.205 0.8742 20L 8L
R16 25.400 1.0000 25.390 0.9996 25.411 1.0004 25.402 1.0001 21T 8T 25.393 0.9997 25.380 0.9992 3T 1T
R18 28.575 1.1250 28.565 1.1246 28.586 1.1254 28.577 1.1251 28.568 1.1247 28.555 1.1242
R20 31.750 1.2500 31.737 1.2495 31.763 1.2505 31.752 1.2501 31.741 1.2496 31.725 1.2490
R24 38.100 1.5000 38.087 1.4995 38.113 1.5005 38.102 1.5001 38.091 1.4996 38.075 1.4990
XLS1³|₈ 34.925 1.3750 34.912 1.3745 34.938 1.3755 34.927 1.3751 2T 1T 34.916 1.3746 34.900 1.3740 25L 10L
XLS1¹|₂ 38.100 1.5000 38.087 1.4995 38.113 1.5005 38.102 1.5001 26T 10T 38.091 1.4996 38.075 1.4990 4T 1T
XLS1⁵|₈ 41.275 1.6250 41.262 1.6245 41.288 1.6255 41.277 1.6251 41.266 1.6246 41.250 1.6240
XLS1³|₄ 44.450 1.7500 44.437 1.7495 44.463 1.7505 44.452 1.7501 44.441 1.7496 44.425 1.7490
XLS1⁷|₈ 47.625 1.8750 47.612 1.8745 47.638 1.8755 47.627 1.8751 47.616 1.8746 47.600 1.8740
XLS2 50.800 2.0000 50.785 1.9994 50.815 2.0006 50.802 2.0001 50.790 1.9996 50.771 1.9989
XLS2¹|₈ 53.975 2.1250 53.960 2.1244 53.990 2.1256 53.977 2.1251 53.965 2.1246 53.946 2.1239
XLS2¹|₄ 57.150 2.2500 57.135 2.2494 57.165 2.2506 57.152 2.2501 2T 1T 57.140 2.2496 57.121 2.2489 29L 11L
XLS2¹|₂ 63.500 2.5000 63.485 2.4994 63.515 2.5006 63.502 2.5001 30T 12T 63.490 2.4996 63.471 2.4989 5T 2T
XLS2⁵|₈ 66.675 2.6250 66.660 2.6244 66.690 2.6256 66.677 2.6251 66.665 2.6246 66.646 2.6239
XLS2³|₄ 69.850 2.7500 69.835 2.7494 69.865 2.7506 69.852 2.7501 69.840 2.7496 69.821 2.7489
XLS3 76.200 3.0000 76.185 2.9994 76.215 3.0006 76.202 3.0001 76.190 2.9996 76.171 2.9989
XLS3¹|₄ 82.550 3.2500 82.530 3.2492 82.568 3.2507 82.553 3.2501 82.538 3.2495 82.516 3.2487
XLS3¹|₂ 88.900 3.5000 88.880 3.4992 88.918 3.5007 88.903 3.5001 3T 1T 88.888 3.4995 88.866 3.4987 34L 13L
XLS3³|₄ 95.250 3.7500 95.230 3.7492 95.268 3.7507 95.253 3.7501 38T 15T 95.238 3.7495 95.216 3.7487 8T 3T
XLS4¹|₄ 107.950 4.2500 107.935 4.2492 107.973 4.2507 107.953 4.2501 107.943 4.2495 107.916 4.2487
XLS4¹|₂ 114.300 4.5000 114.285 4.4992 114.323 4.5007 114.303 4.5001 114.293 4.4995 114.266 4.4987
XLS4³|₄ 120.650 4.7500 120.625 4.7490 120.671 4.7508 120.653 4.7501 120.636 4.7494 120.611 4.7485
XLS5 127.000 5.0000 126.975 4.9990 127.021 5.0008 127.003 5.0001 126.986 4.9994 126.961 4.9985
XLS5¹|₂ 139.700 5.5000 139.675 5.4990 139.721 5.5008 139.703 5.5001 3T 1T 139.686 5.4994 139.661 5.4985 39L 15L
XLS6 152.400 6.0000 152.375 5.9990 152.421 6.0008 152.403 6.0001 46T 18T 152.386 5.9994 152.361 5.9985 11T 4T
XLS6¹|₄ 158.750 6.2500 158.735 6.2490 158.781 6.2508 158.753 6.2501 158.746 6.2494 158.711 6.2485
XLS6¹|₂ 165.100 6.5000 165.075 6.4990 165.121 6.5008 165.103 6.5001 165.086 6.4994 165.061 6.4985
XLS7 177.800 7.0000 177.775 6.9990 177.821 7.0008 177.803 7.0001 177.786 6.9994 177.761 6.9985
XLS7¹|₄ 184.150 7.2500 184.120 7.2488 184.174 7.2509 184.154 7.2502 184.135 7.2494 184.106 7.2483
XLS7³|₄ 196.850 7.7500 196.820 7.7488 196.874 7.7509 196.854 7.7502 196.835 7.7494 196.806 7.7483 44L 17L
XLS8 203.200 8.0000 203.170 7.9988 203.224 8.0009 203.204 8.0002 4T 2T 203.185 7.9994 203.156 7.9983 15T 6T
XLS8¹|₄ 209.950 8.2500 209.520 8.2488 209.574 8.2509 209.554 8.2502 54T 21T 209.535 8.2494 209.506 8.2483
XLS8¹|₂ 215.900 8.5000 215.870 8.4988 215.924 8.5009 215.904 8.5002 215.885 8.4994 215.856 8.4983
XLS9 228.600 9.0000 228.570 8.9988 228.624 9.0009 228.604 9.0002 228.585 8.9994 228.556 8.9983
XLS10 254.000 10.0000 253.965 9.9986 254.027 10.0011 254.004 10.0002 4T 2T 253.983 9.9993 253.951 9.9981 49L 19L
62T 25T 18T 7T
251
Housing Bore Limits—ABEC-1 MRC Bearing Services
General Recommended Housing Bore Limits for Metric Bearings—ISO H6 and N6
Bearing Outside Diameter Housing Stationary Housing Rotating
Max Min Housing Bore (H6) Fit Housing Bore (N6) Fit
mm Max Min Max Min
.001 .0001 .001 .0001
mm in mm in mm in mm in mm in mm in mm in mm in
16 16 0.6299 15.992 0.6296 16.011 0.6303 16 0.6299 19L 7L 15.993 0.6295 15.980 0.6291 2T 1T
0 0 20T 8T
19 19 0.7480 18.991 0.7476 19.013 0.7485 19 0.7480 18.989 0.7476 18.976 0.7471
21 21 0.8268 20.991 0.8264 21.013 0.8273 21 0.8268 20.989 0.8264 20.976 0.8259
22 22 0.8661 21.991 0.8657 22.013 0.8666 22 0.8661 21.989 0.8657 21.976 0.8652
24 24 0.9449 23.991 0.9445 24.013 0.9454 24 0.9449 22L 9L 23.989 0.9445 23.976 0.9440 2T 0
26 26 1.0236 25.991 1.0232 26.013 1.0241 26 1.0236 0 0 25.989 1.0232 25.976 1.0227 24T 9T
28 28 1.1024 27.991 1.1020 28.013 1.1029 28 1.1024 27.989 1.1020 27.976 1.1015
30 30 1.1811 29.991 1.1807 30.013 1.1816 30 1.1811 29.989 1.1807 29.976 1.1802
32 32 1.2598 31.989 1.2593 32.016 1.2604 32 1.2598 31.988 1.2593 31.972 1.2587
35 35 1.3780 34.989 1.3775 35.016 1.3786 35 1.3780 34.988 1.3775 34.972 1.3769
37 37 1.4567 36.989 1.4562 37.016 1.4573 37 1.4567 27L 11L 36.988 1.4562 36.972 1.4556 1T 0
40 40 1.5748 39.989 1.5743 40.016 1.5754 40 1.5748 0 0 39.988 1.5743 39.972 1.5737 28T 11T
42 42 1.6535 41.989 1.6530 42.016 1.6541 42 1.6535 41.988 1.6530 41.972 1.6524
47 47 1.8504 46.989 1.8499 47.016 1.8510 47 1.8504 46.988 1.8499 46.972 1.8493
52 52 2.0472 51.987 2.0467 52.019 2.0479 52 2.0472 51.986 2.0466 51.967 2.0459
55 55 2.1654 54.987 2.1649 55.019 2.1661 55 2.1654 54.986 2.1648 54.967 2.1641
58 58 2.2835 57.987 2.2830 58.019 2.2842 58 2.2835 57.986 2.2829 57.967 2.2822
62 62 2.4409 61.987 2.4404 62.019 2.4416 62 2.4409 61.986 2.4403 61.967 2.4396 1T 1T
65 65 2.5591 64.987 2.5586 65.019 2.5598 65 2.5591 32L 12L 64.986 2.5585 64.967 2.5578
68 68 2.6772 67.987 2.6767 68.019 2.6779 68 2.6772 0 0 67.986 2.6766 67.967 2.6759 33T 13T
70 70 2.7559 69.987 2.7554 70.019 2.7566 70 2.7559 69.986 2.7553 69.967 2.7546
72 72 2.8346 71.987 2.8341 72.019 2.8353 72 2.8346 71.986 2.8340 71.967 2.8333
75 75 2.9528 74.987 2.9523 75.019 2.9535 75 2.9528 74.986 2.9522 74.967 2.9515
78 78 3.0709 77.987 3.0704 78.019 3.0716 78 3.0709 77.986 3.0703 77.967 3.0696
80 80 3.1496 79.987 3.1491 80.019 3.1503 80 3.1496 79.986 3.1490 79.967 3.1483
85 85 3.3465 84.985 3.3459 85.022 3.3474 85 3.3465 84.984 3.3459 84.962 3.3450
90 90 3.5433 89.985 3.5427 90.022 3.5442 90 3.5433 89.984 3.5427 89.962 3.5418
95 95 3.7402 94.985 3.7396 95.022 3.7411 95 3.7402 94.984 3.7396 94.962 3.7387
100 100 3.9370 99.985 3.9364 100.022 3.9379 100 3.9370 37L 15L 99.984 3.9364 99.962 3.9355 1T 0
105 105 4.1339 104.985 4.1333 105.022 4.1348 105 4.1339 0 0 104.984 4.1333 104.962 4.1324 38T 15T
110 110 4.3307 109.985 4.3301 110.022 4.3316 110 4.3307 109.984 4.3301 109.962 4.3292
115 115 4.5276 114.985 4.5270 115.022 4.5285 115 4.5276 114.984 4.5270 114.962 4.5261
120 120 4.7244 119.985 4.7238 120.022 4.7253 120 4.7244 119.984 4.7238 119.962 4.7229
125 125 4.9213 124.982 4.9206 125.025 4.9223 125 4.9213 124.980 4.9205 124.955 4.9195
130 130 5.1181 129.982 5.1174 130.025 5.1191 130 5.1181 129.980 5.1173 129.955 5.1163
135 135 5.3150 134.982 5.3143 135.025 5.3160 135 5.3150 134.980 5.3142 134.955 5.3132
140 140 5.5118 139.982 5.5111 140.025 5.5128 140 5.5118 43L 17L 139.980 5.5110 139.955 5.5100 2T 1T
145 145 5.7087 144.982 5.7080 145.025 5.7097 145 5.7087 0 0 144.980 5.7079 144.955 5.7069 45T 18T
150 150 5.9055 149.982 5.9048 150.025 5.9065 150 5.9055 149.980 5.9047 149.955 5.9037
160 160 6.2992 159.975 6.2982 160.025 6.3002 160 6.2992 159.980 6.2984 159.955 6.2973
165 165 6.4961 164.975 6.4951 165.025 6.4971 165 6.4961 50L 20L 164.980 6.4953 164.955 6.4942 5L 2L
170 170 6.6929 169.975 6.6919 170.025 6.6939 170 6.6929 0 0 169.980 6.6921 169.955 6.6910 45T 19T
175 175 6.8898 174.975 6.8888 175.025 6.8908 175 6.8898 174.980 6.8890 174.955 6.8879
180 180 7.0866 179.975 7.0856 180.025 7.0876 180 7.0866 179.980 7.0858 179.955 7.0847
190 190 7.4803 189.970 7.4791 190.029 7.4814 190 7.4803 189.978 7.4794 189.949 7.4783
200 200 7.8740 199.970 7.8728 200.029 7.8751 200 7.8740 199.978 7.8731 199.949 7.8720
205 205 8.0709 204.970 8.0697 205.029 8.0720 205 8.0709 204.978 8.0700 204.949 8.0689
210 210 8.2677 209.970 8.2665 210.029 8.2688 210 8.2677 209.978 8.2668 209.949 8.2657
215 215 8.4646 214.970 8.4634 215.029 8.4657 215 8.4646 59L 23L 214.978 8.4637 214.949 8.4626 8L 3L
220 220 8.6614 219.970 8.6602 220.029 8.6625 220 8.6614 0 0 219.978 8.6605 219.949 8.6594 51T 20T
225 225 8.8583 224.970 8.8571 225.029 8.8594 225 8.8583 224.978 8.8574 224.949 8.8563
230 230 9.0551 229.970 9.0539 230.029 9.0562 230 9.0551 229.978 9.0542 229.949 9.0531
235 235 9.2520 234.970 9.2508 235.029 9.2531 235 9.2520 234.978 9.2511 234.949 9.2500
240 240 9.4488 239.970 9.4476 240.029 9.4499 240 9.4488 239.978 9.4479 239.949 9.4468
250 250 9.8425 249.970 9.8413 250.029 9.8436 250 9.8425 249.978 9.8416 249.949 9.8405
260 260 10.2362 259.965 10.2348 260.032 10.2375 260 10.2362 259.975 10.2352 259.943 10.2340
265 265 10.4331 264.965 10.4317 265.032 10.4344 265 10.4331 264.975 10.4321 264.943 10.4309
270 270 10.6299 269.965 10.6285 270.032 10.6312 270 10.6299 269.975 10.6289 269.943 10.6277
280 280 11.0236 279.965 11.0222 280.032 11.0249 280 11.0236 67L 27L 279.975 11.0226 279.943 11.0214 10L 4L
290 290 11.4173 289.905 11.4159 290.032 11.4186 290 11.4173 0 0 289.975 11.4163 289.943 11.4151 57T 22T
300 300 11.8110 299.965 11.8096 300.032 11.8123 300 11.8110 299.975 11.8100 299.943 11.8088
310 310 12.2047 309.965 12.2033 310.032 12.2060 310 12.2047 309.975 12.2037 309.943 12.2025
320 320 12.5984 319.960 12.5968 320.036 12.5998 320 12.5984 319.974 12.5974 319.939 12.5960
340 340 13.3858 339.960 13.3842 340.036 13.3872 340 13.3858 339.974 13.3848 339.939 13.3834
350 350 13.7795 349.960 13.7779 350.036 13.7809 350 13.7795 349.974 13.7785 349.939 13.7771
360 360 14.1732 359.960 14.1716 360.036 14.1746 360 14.1732 76L 30L 359.974 14.1722 359.939 14.1708 14L 6L
370 370 14.5669 369.960 14.5653 370.036 14.5683 370 14.5669 0 0 369.974 14.5659 369.939 14.5645 61T 24T
380 380 14.9606 379.960 14.9590 380.036 14.9620 380 14.9606 379.974 14.9596 379.939 14.9582
390 390 15.3543 389.960 15.3527 390.036 15.3557 390 15.3543 389.974 15.3533 389.939 15.3519
400 400 15.7480 399.960 15.7464 400.036 15.7494 400 15.7480 399.974 15.7470 399.939 15.7456
410 410 16.1417 409.955 16.1399 410.040 16.1433 410 16.1417 409.973 16.1406 409.933 16.1391
420 420 16.5354 419.955 16.5336 420.040 16.5370 420 16.5354 419.973 16.5343 419.933 16.5328
430 430 16.9291 429.955 16.9273 430.040 16.9307 430 16.9291 429.973 16.9280 429.933 16.9265
440 440 17.3228 439.955 17.3210 440.040 17.3244 440 17.3228 85L 34L 439.973 17.3217 439.933 17.3202 18L 7L
460 460 18.1102 459.955 18.1084 460.040 18.1118 460 18.1102 0 0 459.973 18.1091 459.933 18.1076 67T 26T
480 480 18.8976 479.955 18.8958 480.040 18.8992 480 18.8976 479.973 18.8965 479.933 18.8950
500 500 19.6850 499.955 19.6832 500.040 19.6866 500 19.6850 499.973 19.6839 499.933 19.6824
520 520 20.4724 519.950 20.4704 520.044 20.4741 520 20.4724 519.956 20.4707 519.911 20.4689 6L 3L
540 540 21.2598 539.950 21.2578 540.044 21.2615 540 21.2598 539.956 21.2581 539.911 21.2563 89T 35T
560 560 22.0472 559.950 22.0452 560.044 22.0489 560 22.0472 94L 37L 559.956 22.0455 559.911 22.0437
580 580 22.8346 579.950 22.8326 580.044 22.8363 580 22.8346 0 0 579.956 22.8329 579.911 22.8311
600 600 23.6220 599.950 23.6200 600.044 23.6237 600 23.6220 599.956 23.6203 599.911 23.6185
620 620 24.4094 619.950 24.4074 620.044 24.4111 620 24.4094 619.956 24.4077 619.911 24.4059
For aluminum or other soft metal housings make bore limits same as bearing O.D. limits.
252
Housing Bore Limits—ABEC-1
General Recommended Housing Bore Limits for Inch-Size Bearings— ISO H6 and N6
Bearing Outside Diameter Housing Stationary Housing Rotating
Max Min Housing Bore (H6) Fit Housing Bore (N6) Fit
mm Max Min Max Min
.001 .0001 .001 .0001
mm in mm in mm in mm in mm in mm in mm in mm in
R2 9.525 0.3750 9.517 0.3747 9.536 0.3754 9.525 0.3750 9.515 0.3746 9.505 0.3742
R2A 12.700 0.5000 12.692 0.4997 12.711 0.5004 12.700 0.5000 19L 7L 12.690 0.4996 12.680 0.4992 2T 1T
R3 12.700 0.5000 12.692 0.4997 12.711 0.5004 12.700 0.5000 0 0 12.690 0.4996 12.680 0.4992 20T 8T
R4 15.875 0.6250 15.867 0.6247 15.886 0.6254 15.875 0.6250 15.865 0.6246 15.855 0.6242
R4A 19.050 0.7500 19.041 0.7496 19.063 0.7505 19.050 0.7500 22L 9L 19.039 0.7496 19.026 0.7491 2T 0
R6 22.225 0.8750 22.216 0.8746 22.238 0.8755 22.225 0.8750 0 0 22.214 0.8746 22.201 0.8741 24T 9T
R8 28.575 1.1250 28.566 1.1246 28.588 1.1255 28.575 1.1250 28.564 1.1246 28.551 1.1241
R10 34.925 1.3750 34.914 1.3745 34.941 1.3756 34.925 1.3750 27L 11L 34.913 1.3744 34.897 1.3739 1T 1T
R12 41.275 1.6250 41.264 1.6245 41.291 1.6256 41.275 1.6250 0 0 41.263 1.6244 41.247 1.6239 28T 11T
R14 47.625 1.8750 47.614 1.8745 47.641 1.8756 47.625 1.8750 47.613 1.8744 47.597 1.8739
R16 50.800 2.0000 50.787 1.9995 50.819 2.0007 50.800 2.0000 50.786 1.9994 50.767 1.9987
R18 53.975 2.1250 53.962 2.1245 53.994 2.1257 53.975 2.1250 53.961 2.1244 53.942 2.1237
R20 57.150 2.2500 57.137 2.2495 57.169 2.2507 57.150 2.2500 32L 12L 57.136 2.2494 57.117 2.2487 1T 1T
R24 66.675 2.6250 66.662 2.6245 66.694 2.6257 66.675 2.6250 0 0 66.661 2.6244 66.642 2.6237 33T 13T
XLS1³|₈ 65.088 2.5625 65.151 2.5620 65.183 2.5632 65.088 2.5625 65.150 2.5619 65.055 2.5612
XLS1¹|₂ 68.263 2.6875 68.250 2.6870 68.282 2.6882 68.263 2.6875 68.249 2.6869 68.230 2.6862
XLS1³|₈ 73.025 2.8750 73.012 2.8745 73.044 2.8757 73.025 2.8750 73.011 2.8744 72.992 2.8737
XLS1³|₄ 76.200 3.0000 76.187 2.9995 76.219 3.0007 76.200 3.0000 76.186 2.9994 76.167 2.9987
XLS1⁷|₈ 80.963 3.1875 80.948 3.1869 80.985 3.1884 80.963 3.1875 80.947 3.1869 80.925 3.1860
XLS2 84.138 3.3125 84.123 3.3119 84.160 3.3134 84.138 3.3125 84.122 3.3119 84.100 3.3110
XLS2¹|₈ 87.313 3.4375 87.298 3.4369 87.335 3.4384 87.313 3.4375 37L 15L 87.297 3.4369 87.275 3.4360 1T 0
XLS2¹|₄ 90.488 3.5625 90.473 3.5619 90.510 3.5634 90.488 3.5625 0 0 90.472 3.5619 90.450 3.5610 38T 15T
XLS2¹|₂ 98.425 3.8750 98.410 3.8744 98.447 3.8759 98.425 3.8750 98.409 3.8744 98.387 3.8735
XLS2⁵|₈ 104.775 4.1250 104.760 4.1244 104.797 4.1259 104.775 4.1250 104.759 4.1244 104.737 4.1235
XLS2³|₄ 104.775 4.1250 104.760 4.1244 104.797 4.1259 104.775 4.1250 104.759 4.1244 104.737 4.1235
XLS3 114.300 4.5000 114.285 4.4994 114.322 4.5009 114.300 4.5000 114.284 4.4994 114.262 4.4985
XLS3¹|₄ 120.650 4.7500 120.632 4.7493 120.675 4.7510 120.650 4.7500 43L 17L 120.630 4.7492 120.605 4.7482 2T 1T
XLS3¹|₂ 127.000 5.0000 126.982 4.9993 126.995 5.0010 127.000 5.0000 0 0 126.980 4.9992 126.955 4.9982 45T 18T
XLS3³|₄ 133.350 5.2500 133.332 5.2493 133.375 5.2510 133.350 5.2500 133.330 5.2492 133.305 5.2482
XLS4¹|₄ 152.400 6.0000 152.375 5.9990 152.425 6.0010 152.400 6.0000 152.380 5.9992 152.355 5.9981
XLS4¹|₂ 158.750 6.2500 158.725 6.2490 158.775 6.2510 158.750 6.2500 50L 20L 158.730 6.2492 158.705 6.2481 5L 2L
XLS4³|₄ 165.100 6.5000 165.075 6.4990 165.125 6.5010 165.100 6.5000 0 0 165.080 6.4992 165.055 6.4981 45T 18T
XLS5 177.800 7.0000 177.775 6.9990 177.825 7.0010 177.800 7.0000 177.780 6.9992 177.755 6.9981
XLS5¹|₂ 190.500 7.5000 190.470 7.4988 190.529 7.5011 190.500 7.5000 190.478 7.4991 190.449 7.4980
XLS6 203.200 8.0000 203.170 7.9988 203.229 8.0011 203.200 8.0000 203.178 7.9991 203.149 7.9980
XLS6¹|₄ 215.900 8.5000 215.870 8.4988 215.929 8.5011 215.900 8.5000 59L 23L 215.878 8.4991 215.849 8.4980 8L 3L
XLS6¹|₂ 222.250 8.7500 222.220 8.7488 222.279 8.7511 222.250 8.7500 0 0 222.228 8.7491 222.199 8.7480 51T 20T
XLS7 241.300 9.5000 241.270 9.4988 241.329 9.5011 241.300 9.5000 241.278 9.4991 241.249 9.4980
XLS7¹|₄ 247.650 9.7500 247.620 9.7488 247.679 9.7511 247.650 9.7500 247.628 9.7491 247.599 9.7480
XLS7³|₄ 266.700 10.5000 266.665 10.4986 266.732 10.5013 266.700 10.5000 266.675 10.4990 266.643 10.4978
XLS8 273.051 10.7500 273.016 10.7486 273.083 10.7513 273.051 10.7500 67L 27L 273.026 10.7490 272.994 10.7478 10L 4L
XLS8¹|₄ 279.401 11.0000 279.366 10.9986 279.433 11.0013 279.401 11.0000 0 0 279.376 10.9990 279.344 10.9978 57T 22T
XLS8¹|₂ 292.101 11.5000 292.066 11.4986 292.133 11.5013 292.101 11.5000 292.076 11.4990 292.044 11.4978
XLS9 304.801 12.0000 304.766 11.9986 304.833 12.0013 304.801 12.0000 304.776 11.9990 304.744 11.9978
XLS10 336.551 13.2500 336.514 13.2484 336.587 13.2514 336.551 13.2500 76L 30L 336.525 13.2490 336.489 13.2476 14L 6L
0 0 62T 24T
For aluminum or other soft metal housings make bore limits same as bearing O.D. limits.
253
Shaft Limits—ABEC-3 MRC Bearing Services
4 4 0.1575 3.993 0.1572 4.006 0.1577 4.000 0.1575 0 0 3.996 0.1573 3.988 0.1570 12L 5L
5 5 0.1969 4.993 0.1966 5.006 0.1971 5.000 0.1969 13T 5T 4.996 0.1967 4.988 0.1964 3T 1T
6 6 0.2362 5.993 0.2359 6.006 0.2364 6.000 0.2362 5.996 0.2360 5.988 0.2357
7 7 0.2756 6.993 0.2753 7.007 0.2759 7.000 0.2756 6.995 0.2754 6.986 0.2750
8 8 0.3150 7.993 0.3147 8.007 0.3153 8.000 0.3150 0 0 7.995 0.3148 7.986 0.3144 14L 6L
9 9 0.3543 8.993 0.3540 9.007 0.3546 9.000 0.3543 14T 6T 8.995 0.3541 8.986 0.3537 2T 1T
10 10 0.3937 9.993 0.3934 10.007 0.3940 10.000 0.3937 9.995 0.3935 9.986 0.3931
12 12 0.4724 11.993 0.4721 12.009 0.4728 12.000 0.4724 0 0 11.994 0.4722 11.983 0.4717 17L 7L
15 15 0.5906 14.993 0.5903 15.009 0.5910 15.000 0.5906 16T 7T 14.994 0.5904 14.983 0.5899 1T 1T
17 17 0.6693 16.993 0.6690 17.009 0.6697 17.000 0.6693 16.994 0.6691 16.983 0.6686
20 20 0.7874 19.992 0.7871 20.011 0.7878 20.002 0.7875 2T 1T 19.993 0.7871 19.980 0.7866 20L 8L
25 25 0.9843 24.992 0.9840 25.011 0.9847 25.002 0.9844 19T 7T 24.993 0.9840 24.980 0.9835 1T 0
30 30 1.1811 29.992 1.1808 30.011 1.1815 30.002 1.1812 29.993 1.1808 29.980 1.1803
35 35 1.3780 34.990 1.3776 35.013 1.3785 35.002 1.3781 34.991 1.3776 34.975 1.3770
40 40 1.5748 39.990 1.5744 40.013 1.5753 40.002 1.5749 2T 1T 39.991 1.5744 39.975 1.5738 25L 10L
45 45 1.7717 44.990 1.7713 45.013 1.7722 45.002 1.7718 23T 9T 44.991 1.7713 44.975 1.7707 1T 0
50 50 1.9685 49.990 1.9681 50.013 1.9690 50.002 1.9686 49.991 1.9681 49.975 1.9675
55 55 2.1654 54.988 2.1649 55.015 2.1660 55.002 2.1655 54.990 2.1650 54.971 2.1643
60 60 2.3622 59.988 2.3617 60.015 2.3628 60.002 2.3623 59.990 2.3618 59.971 2.3611
65 65 2.5591 64.988 2.5586 65.015 2.5597 65.002 2.5592 2T 1T 64.990 2.5587 64.971 2.5580 29L 11L
70 70 2.7559 69.988 2.7554 70.015 2.7565 70.002 2.7560 27T 11T 69.990 2.7555 69.971 2.7548 2T 1T
75 75 2.9528 74.988 2.9523 75.015 2.9534 75.002 2.9529 74.990 2.9524 74.971 2.9517
80 80 3.1496 79.988 3.1491 80.015 3.1502 80.002 3.1497 79.990 3.1492 79.971 3.1485
85 85 3.3465 84.985 3.3459 85.018 3.3472 85.003 3.3466 84.988 3.3460 84.966 3.3452
90 90 3.5433 89.985 3.5427 90.018 3.5440 90.003 3.5434 89.988 3.5428 89.966 3.5420
95 95 3.7402 94.985 3.7396 95.018 3.7409 95.003 3.7403 3T 1T 94.988 3.7397 94.966 3.7389 34L 13L
100 100 3.9370 99.985 3.9364 100.018 3.9377 100.003 3.9371 33T 13T 99.988 3.9365 99.966 3.9357 3T 1T
105 105 4.1339 104.985 4.1333 105.018 4.1346 105.003 4.1340 104.988 4.1334 104.966 4.1326
110 110 4.3307 109.985 4.3301 110.018 4.3314 110.003 4.3308 109.988 4.3302 109.966 4.3294
115 115 4.5276 114.985 4.5270 115.018 4.5283 115.003 4.5277 114.988 4.5271 114.966 4.5263
120 120 4.7244 119.985 4.7238 120.018 4.7251 120.003 4.7245 119.988 4.7239 119.966 4.7231
125 125 4.9213 124.982 4.9206 125.021 4.9221 125.003 4.9214 124.986 4.9207 124.961 4.9198
130 130 5.1181 129.982 5.1174 130.021 5.1189 130.003 5.1182 129.986 5.1175 129.961 5.1166
140 140 5.5118 139.982 5.5111 140.021 5.5126 140.003 5.5119 3T 1T 139.986 5.5112 139.961 5.5103 39L 15L
150 150 5.9055 149.982 5.9048 150.021 5.9063 150.003 5.9056 39T 15T 149.986 5.9049 149.961 5.9040 4T 1T
160 160 6.2992 159.982 6.2985 160.021 6.3000 160.003 6.2993 159.986 6.2986 159.961 6.2977
170 170 6.6929 169.982 6.6922 170.021 6.6937 170.003 6.6930 169.986 6.6923 169.961 6.6914
180 180 7.0866 179.982 7.0859 180.021 7.0874 180.003 7.0867 179.986 7.0860 179.961 7.0851
190 190 7.4803 189.978 7.4794 190.024 7.4812 190.004 7.4805 189.985 7.4797 189.956 7.4786
200 200 7.8740 199.978 7.8731 200.024 7.8749 200.004 7.8742 199.985 7.8734 199.956 7.8723
210 210 8.2677 209.978 8.2668 210.024 8.2684 210.004 8.2679 4T 2T 209.985 8.2671 209.956 8.2660
220 220 8.6614 219.978 8.6605 220.024 8.6623 220.004 8.6616 219.985 8.6608 219.956 8.6597 44L 17L
230 230 9.0551 229.978 9.0542 230.024 9.0560 230.004 9.0553 46T 18T 229.985 9.0545 229.956 9.0534 7T 3T
240 240 9.4488 239.978 9.4479 240.024 9.4497 240.004 9.4490 239.985 9.4482 239.956 9.4471
250 250 9.8425 249.978 9.8416 250.024 9.8434 250.004 9.8427 249.985 9.8419 249.956 9.8408
260 260 10.2362 259.975 10.2352 260.027 10.2373 260.004 10.2364 4T 2T 259.983 10.2355 259.951 10.2343 49L 19L
280 280 11.0236 279.975 11.0226 280.027 11.0247 280.004 11.0238 52T 21T 279.983 11.0229 279.951 11.0217 8T 3T
300 300 11.8110 299.975 11.8100 300.027 11.8121 300.004 11.8112 299.983 11.8103 299.951 11.8091
320 320 12.5984 319.970 12.5972 320.029 12.5995 320.004 12.5986 4T 2T 319.982 12.5977 319.946 12.5963 54L 21L
59T 23T 12T 5T
254
Shaft Limits—ABEC-3
R2 3.175 0.1250 3.168 0.1247 3.181 0.1252 3.175 0.1250 0 0 3.171 0.1248 3.163 0.1245 12L 5L
R2A 3.175 0.1250 3.168 0.1247 3.181 0.1252 3.175 0.1250 13T 5T 3.171 0.1248 3.163 0.1245 3T 1T
R3 4.763 0.1875 4.756 0.1872 4.769 0.1877 4.768 0.1875 4.759 0.1873 4.751 0.1870
R4 6.350 0.2500 6.343 0.2497 6.357 0.2503 6.350 0.2500 0 0 6.345 0.2498 6.336 0.2494 14L 6L
R4A 6.350 0.2500 6.343 0.2497 6.357 0.2503 6.350 0.2500 14T 6T 6.345 0.2498 6.336 0.2494 2T 1T
R6 9.525 0.3750 9.518 0.3747 9.532 0.3753 9.525 0.3750 9.520 0.3748 9.511 0.3744
R8 12.700 0.5000 12.693 0.4997 12.709 0.5004 12.700 0.5000 0 0 12.694 0.4998 12.683 0.4993 17L 7L
R10 15.875 0.6250 15.868 0.6247 15.884 0.6254 15.875 0.6250 16T 7T 15.869 0.6248 15.858 0.6243 1T 1T
R12 19.050 0.7500 19.042 0.7497 19.061 0.7504 19.052 0.7501 19.043 0.7497 19.030 0.7492
R14 22.225 0.8750 22.217 0.8747 22.236 0.8754 22.227 0.8751 2T 1T 22.218 0.8747 22.205 0.8742 20L 8L
R16 25.400 1.0000 25.392 0.9997 25.411 1.0004 25.402 1.0001 19T 7T 25.393 0.9997 25.380 0.9992 1T 0
R18 28.575 1.1250 28.567 1.1247 28.586 1.1254 28.577 1.1251 28.568 1.1247 28.555 1.1242
R20 31.750 1.2500 31.740 1.2496 31.763 1.2505 31.752 1.2501 31.741 1.2496 31.725 1.2490
R24 38.100 1.5000 38.090 1.4996 38.113 1.5005 38.102 1.5001 38.091 1.4996 38.075 1.4990
XLS1³|₈ 34.925 1.3750 34.915 1.3746 34.938 1.3755 34.927 1.3751 2T 1T 34.916 1.3746 34.900 1.3740 25L 10L
XLS1¹|₂ 38.100 1.5000 38.090 1.4996 38.113 1.5005 38.102 1.5001 23T 9T 38.091 1.4996 38.075 1.4990 1T 0
XLS1⁵|₈ 41.275 1.6250 41.265 1.6246 41.288 1.6255 41.277 1.6251 41.266 1.6246 41.250 1.6240
XLS1³|₄ 44.450 1.7500 44.440 1.7496 44.463 1.7505 44.452 1.7501 44.441 1.7496 44.425 1.7490
XLS1⁷|₈ 47.625 1.8750 47.615 1.8746 47.638 1.8755 47.627 1.8751 47.616 1.8746 47.600 1.8740
XLS2 50.800 2.0000 50.788 1.9995 50.815 2.0006 50.802 2.0001 50.790 1.9996 50.771 1.9989
XLS2¹|₈ 53.975 2.1250 53.963 2.1245 53.990 2.1256 53.977 2.1251 53.965 2.1246 53.946 2.1239
XLS2¹|₄ 57.150 2.2500 57.138 2.2495 57.165 2.2506 57.152 2.2501 2T 1T 57.140 2.2496 57.121 2.2489 29L 11L
XLS2¹|₂ 63.500 2.5000 63.488 2.4995 63.515 2.5006 63.502 2.5001 27T 11T 63.490 2.4996 63.471 2.4989 2T 1T
XLS2⁵|₈ 66.675 2.6250 66.663 2.6245 66.690 2.6256 66.677 2.6251 66.665 2.6246 66.646 2.6239
XLS2³|₄ 69.850 2.7500 69.838 2.7495 69.865 2.7506 69.852 2.7501 69.840 2.7496 69.821 2.7489
XLS3 76.200 3.0000 76.188 2.9995 76.215 3.0006 76.202 3.0001 76.190 2.9996 76.121 2.9989
XLS3¹|₄ 82.550 3.2500 82.585 3.2494 82.568 3.2507 82.553 3.2501 82.538 3.2495 82.516 3.2487
XLS3¹|₂ 88.900 3.5000 88.885 3.4994 88.918 3.5007 88.903 3.5001 3T 1T 88.888 3.4995 88.866 3.4987 34L 13L
XLS3³|₄ 95.250 3.7500 95.235 3.7494 95.268 3.7507 95.253 3.7501 33T 13T 95.238 3.7495 95.216 3.7487 3T 1T
XLS4¹|₄ 107.950 4.2500 107.935 4.2494 107.968 4.2507 107.953 4.2501 107.938 4.2495 107.916 4.2487
XLS4¹|₂ 114.300 4.5000 114.285 4.4994 114.318 4.5007 114.303 4.5001 114.288 4.4995 114.266 4.4987
XLS4³|₄ 120.650 4.7500 120.632 4.7493 120.671 4.7508 120.653 4.7501 120.636 4.7494 120.611 4.7485
XLS5 127.000 5.0000 126.982 4.9993 127.021 5.0008 127.003 5.0001 126.986 4.9994 126.961 4.9985
XLS5¹|₂ 139.700 5.5000 139.682 5.4993 139.721 5.5008 139.703 5.5001 3T 1T 139.686 5.4994 139.661 5.4985 39L 15L
XLS6 152.400 6.0000 152.382 5.9993 152.421 6.0008 152.403 6.0001 39T 15T 152.386 5.9994 152.361 5.9985 4T 1T
XLS6¹|₄ 158.750 6.2500 158.732 6.2493 158.771 6.2508 158.753 6.2501 158.736 6.2494 158.711 6.2485
XLS6¹|₂ 165.100 6.5000 165.082 6.4993 165.121 6.5008 165.103 6.5001 165.086 6.4994 165.061 6.4985
XLS7 177.800 7.0000 177.782 6.9993 177.821 7.0008 177.803 7.0001 177.786 6.9994 177.761 6.9985
XLS7¹|₄ 184.150 7.2500 184.128 7.2491 184.174 7.2509 184.154 7.2502 184.135 7.2494 184.106 7.2483
XLS7³|₄ 196.850 7.7500 196.828 7.7491 196.874 7.7509 196.854 7.7502 196.835 7.7494 196.806 7.7483
XLS8 203.200 8.0000 203.178 7.9991 203.224 8.0009 203.204 8.0002 4T 2T 203.185 7.9994 203.156 7.9983 44L 17L
XLS8¹|₄ 209.950 8.2500 209.928 8.2491 209.974 8.2509 209.954 8.2502 46T 18T 209.935 8.2494 209.906 8.2483 7T 3T
XLS8¹|₂ 215.900 8.5000 215.878 8.4991 215.924 8.5009 215.904 8.5002 215.885 8.4994 215.856 8.4983
XLS9 228.600 9.0000 228.578 8.9991 228.624 9.0009 228.604 9.0002 228.585 8.9994 228.556 8.9983
XLS10 254.000 10.0000 253.975 9.9990 254.027 10.0011 254.004 10.0002 4T 2T 253.983 9.9993 253.951 9.9981 49L 19L
52T 21T 8T 3T
255
Housing Bore Limits—ABEC-3 MRC Bearing Services
General Recommended Housing Bore Limits for Metric Bearings—ISO H6 and N6
Bearing Outside Diameter Housing Stationary Housing Rotating
Max Min Housing Bore (H6) Fit Housing Bore (N6) Fit
mm Max Min Max Min
.001 .0001 .001 .0001
mm in mm in mm in mm in mm in mm in mm in mm in
16 16 0.6299 15.993 0.6296 16.011 0.6303 16 0.6299 18L 7L 15.993 0.6295 15.980 0.6291 0 1T
0 0 20T 8T
19 19 0.7480 18.992 0.7477 19.013 0.7485 19 0.7480 18.989 0.7476 18.976 0.7471
21 21 0.8268 20.992 0.8265 21.013 0.8273 21 0.8268 20.989 0.8264 20.976 0.8259
22 22 0.8661 21.992 0.8658 22.013 0.8666 22 0.8661 21.989 0.8657 21.976 0.8652
24 24 0.9449 23.992 0.9446 24.013 0.9454 24 0.9449 21L 8L 23.989 0.9445 23.976 0.9440 3T 1T
26 26 1.0236 25.992 1.0233 26.013 1.0241 26 1.0236 0 0 25.989 1.0232 25.976 1.0227 24T 9T
28 28 1.1024 27.992 1.1021 28.013 1.1029 28 1.1024 27.989 1.1020 27.976 1.1015
30 30 1.1811 29.992 1.1808 30.013 1.1816 30 1.1811 29.989 1.1807 29.976 1.1802
32 32 1.2598 31.991 1.2594 32.016 1.2604 32 1.2598 31.988 1.2593 31.972 1.2587
35 35 1.3780 34.991 1.3776 35.016 1.3786 35 1.3780 34.988 1.3775 34.972 1.3769
37 37 1.4567 36.991 1.4563 37.016 1.4573 37 1.4567 25L 10L 36.988 1.4562 36.972 1.4556 3T 1T
40 40 1.5748 39.991 1.5744 40.016 1.5754 40 1.5748 0 0 39.988 1.5743 39.972 1.5737 28T 11T
42 42 1.6535 41.991 1.6531 42.016 1.6541 42 1.6535 41.988 1.6530 41.972 1.6524
47 47 1.8504 46.991 1.8500 47.016 1.8510 47 1.8504 46.988 1.8499 46.972 1.8493
52 52 2.0472 51.989 2.0468 52.019 2.0479 52 2.0472 51.986 2.0466 51.967 2.0459
55 55 2.1654 54.989 2.1650 55.019 2.1661 55 2.1654 54.986 2.1648 54.967 2.1641
58 58 2.2835 57.989 2.2831 58.019 2.2842 58 2.2835 57.986 2.2829 57.967 2.2822
62 62 2.4409 61.989 2.4405 62.019 2.4416 62 2.4409 61.986 2.4403 61.967 2.4396
65 65 2.5591 64.989 2.5587 65.019 2.5598 65 2.5591 30L 11L 64.986 2.5585 64.967 2.5578 3T 2T
68 68 2.6772 67.989 2.6768 68.019 2.6779 68 2.6772 0 0 67.886 2.6766 67.967 2.6759 33T 13T
70 70 2.7559 69.989 2.7555 70.019 2.7566 70 2.7559 69.986 2.7553 69.967 2.7546
72 72 2.8346 71.989 2.8342 72.019 2.8353 72 2.8346 71.986 2.8340 71.967 2.8333
75 75 2.9528 74.989 2.9524 75.019 2.9535 75 2.9528 74.986 2.9522 74.967 2.9515
78 78 3.0709 77.989 3.0705 78.019 3.0716 78 3.0709 77.986 3.0703 77.967 3.0696
80 80 3.1496 79.989 3.1492 80.019 3.1503 80 3.1496 79.986 3.1490 79.967 3.1483
85 85 3.3465 84.987 3.3460 85.022 3.3474 85 3.3465 84.984 3.3459 84.962 3.3450
90 90 3.5433 89.987 3.5428 90.022 3.5442 90 3.5433 89.984 3.5427 89.962 3.5418
95 95 3.7402 94.987 3.7397 95.022 3.7411 95 3.7402 94.984 3.7396 94.962 3.7387
100 100 3.9370 99.987 3.9365 100.022 3.9379 100 3.9370 35L 14L 99.984 3.9364 99.962 3.9355 3T 1T
105 105 4.1339 104.987 4.1334 105.022 4.1348 105 4.1339 0 0 104.984 4.1333 104.962 4.1324 38T 15T
110 110 4.3307 109.987 4.3302 110.022 4.3316 110 4.3307 109.984 4.3301 109.962 4.3292
115 115 4.5276 114.987 4.5271 115.022 4.5285 115 4.5276 114.984 4.5270 114.962 4.5261
120 120 4.7244 119.987 4.7239 120.022 4.7253 120 4.7244 119.984 4.7238 119.962 4.7229
125 125 4.9213 124.985 4.9207 125.025 4.9223 125 4.9213 124.980 4.9205 124.955 4.9195
130 130 5.1181 129.985 5.1175 130.025 5.1191 130 5.1181 129.980 5.1173 129.955 5.1163
135 135 5.3150 134.985 5.3144 135.025 5.3160 135 5.3150 40L 16L 134.980 5.3142 134.955 5.3132 5T 2T
140 140 5.5118 139.985 5.5112 140.025 5.5128 140 5.5118 0 0 139.980 5.5110 139.955 5.5100 45T 18T
145 145 5.7087 144.985 5.7081 145.025 5.7097 145 5.7087 144.980 5.7079 144.955 5.7069
150 150 5.9055 149.985 5.9049 150.025 5.9065 150 5.9055 149.980 5.9047 149.955 5.9037
160 160 6.2992 159.982 6.2985 160.025 6.3002 160 6.2992 159.980 6.2984 159.955 6.2973
165 165 6.4961 164.982 6.4954 165.025 6.4971 165 6.4961 164.980 6.4953 164.955 6.4942
170 170 6.6929 169.982 6.6922 170.025 6.6939 170 6.6929 43L 17L 169.980 6.6921 169.955 6.6910 2T 1T
175 175 6.8898 174.982 6.8891 175.025 6.8908 175 6.8898 0 0 174.980 6.8890 174.955 6.8879 45T 19T
180 180 7.0866 179.982 7.0859 180.025 7.0876 180 7.0866 179.980 7.0858 179.955 7.0847
190 190 7.4803 189.980 7.4795 190.029 7.4814 190 7.4803 189.978 7.4794 189.949 7.4783
200 200 7.8740 199.980 7.8732 200.029 7.8751 200 7.8740 199.978 7.8731 199.949 7.8720
205 205 8.0709 204.980 8.0701 205.029 8.0720 205 8.0709 204.978 8.0700 204.949 8.0689
210 210 8.2677 209.980 8.2669 210.029 8.2688 210 8.2677 209.978 8.2668 209.949 8.2657
215 215 8.4646 214.980 8.4638 215.029 8.4657 215 8.4646 49L 19L 214.978 8.4637 214.949 8.4626 2T 1T
220 220 8.6614 219.980 8.6606 220.029 8.6625 220 8.6614 0 0 219.978 8.6605 219.949 8.6594 51T 20T
225 225 8.8583 224.980 8.8575 225.029 8.8594 225 8.8583 224.978 8.8574 224.949 8.8563
230 230 9.0551 229.980 9.0543 230.029 9.0562 230 9.0551 229.978 9.0542 229.949 9.0531
235 235 9.2520 234.980 9.2512 235.029 9.2531 235 9.2520 234.978 9.2511 234.949 9.2500
240 240 9.4488 239.980 9.4480 240.029 9.4499 240 9.4488 239.978 9.4479 239.949 9.4468
250 250 9.8425 249.980 9.8417 250.029 9.8436 250 9.8425 249.978 9.8416 249.949 9.8405
260 260 10.2362 259.975 10.2352 260.032 10.2375 260 10.2362 259.975 10.2352 259.943 10.2340
265 265 10.4331 264.975 10.4321 265.032 10.4344 265 10.4331 264.975 10.4321 264.943 10.4309
270 270 10.6299 269.975 10.6289 270.032 10.6312 270 10.6299 269.975 10.6289 269.943 10.6277
280 280 11.0236 279.975 11.0226 280.032 11.0249 280 11.0236 57L 23L 279.975 11.0226 279.943 11.0214 0 0
290 290 11.4173 289.975 11.4163 290.032 11.4186 290 11.4173 0 0 289.975 11.4163 289.943 11.4151 57T 22T
300 300 11.8110 299.975 11.8100 300.032 11.8123 300 11.8110 299.975 11.8100 299.943 11.8088
310 310 12.2047 309.975 12.2037 310.032 12.2060 310 12.2047 309.975 12.2037 309.943 12.2025
320 320 12.5984 319.972 12.5973 320.036 12.5998 320 12.5984 319.974 12.5974 319.938 12.5958
340 340 13.3858 339.972 13.3847 340.036 13.3872 340 13.3858 339.974 13.3848 339.938 13.3832
350 350 13.7795 349.972 13.7784 350.036 13.7809 350 13.7809 64L 25L 349.974 13.7785 349.938 13.7769 2L 1L
360 360 14.1732 359.972 14.1721 360.036 14.1746 360 14.1732 359.974 14.1722 359.938 14.1706
370 370 14.5669 369.972 14.5658 370.036 14.5683 370 14.5669 0 0 369.974 14.5659 369.938 14.5643 62T 26T
380 380 14.9606 379.972 14.9595 380.036 14.9620 380 14.9606 379.974 14.9596 379.938 14.9580
390 390 15.3543 389.972 15.3532 390.036 15.3557 390 15.3543 389.974 15.3533 389.938 15.3517
400 400 15.7480 399.972 15.7469 400.036 15.7494 400 15.7480 399.974 15.7470 399.938 15.7454
410 410 16.1417 409.967 16.1404 410.040 16.1433 410 16.1417 409.973 16.1406 409.933 16.1391
420 420 16.5354 419.967 16.5341 420.040 16.5370 420 16.5354 419.973 16.5343 419.933 16.5328
430 430 16.9291 429.967 16.9278 430.040 16.9307 430 16.9291 429.973 16.9280 429.933 16.9265
440 440 17.3228 439.967 17.3215 440.040 17.3244 440 17.3228 73L 29L 439.973 17.3217 439.933 17.3202 6L 2L
460 460 18.1102 459.967 18.1089 460.040 18.1118 460 18.1102 0 0 459.973 18.1091 459.933 18.1076 67T 26T
480 480 18.8976 479.967 18.8963 480.040 18.8992 480 18.8976 479.973 18.8965 479.933 18.8950
500 500 19.6850 499.967 19.6837 500.040 19.6866 500 19.6850 499.973 19.6839 499.933 19.6824
520 520 20.4724 519.960 20.4709 520.044 20.4741 520 20.4724 519.966 20.4711 519.912 20.4695
540 540 21.2598 539.960 21.2583 540.044 21.2615 540 21.2598 539.966 21.2585 539.912 21.2569
560 560 22.0472 559.960 22.0457 560.044 22.0489 560 22.0472 84L 32L 559.966 22.0459 559.912 22.0443 6L 2L
580 580 22.8346 579.960 22.8331 580.044 22.8363 580 22.8346 0 0 579.966 22.8333 579.912 22.8317 88T 29T
600 600 23.6220 599.960 23.6205 600.044 23.6237 600 23.6220 599.966 23.6207 599.912 23.6191
620 620 24.4094 619.960 24.4079 620.044 24.4111 620 24.4094 619.966 24.4081 619.912 24.4065
For aluminum or other soft metal housings make bore limits same as bearing O.D. limits.
256
Housing Bore Limits—ABEC-3
R2 9.525 0.3750 9.518 0.3747 9.536 0.3754 9.525 0.3750 9.518 0.3746 9.505 0.3742
R2A 12.700 0.5000 12.693 0.4997 12.711 0.5004 12.700 0.5000 18L 7L 12.693 0.4996 12.680 0.4992 0 1T
R3 12.700 0.5000 12.693 0.4997 12.711 0.5004 12.700 0.5000 0 0 12.693 0.4996 12.680 0.4992 20T 8T
R4 15.875 0.6250 15.868 0.6247 15.886 0.6254 15.875 0.6250 15.868 0.6246 15.855 0.6242
R4A 19.050 0.7500 19.042 0.7497 19.063 0.7505 19.050 0.7500 19.039 0.7496 19.026 0.7491
R6 22.225 0.8750 22.217 0.8747 22.238 0.8755 22.225 0.8750 21L 8L 22.214 0.8746 22.201 0.8741 3T 1T
R8 28.575 1.1250 28.567 1.1247 28.588 1.1255 28.575 1.1250 0 0 28.564 1.1246 28.551 1.1241 24T 9T
R10 34.925 1.3750 34.916 1.3746 34.941 1.3756 34.925 1.3750 25L 10L 34.913 1.3745 34.897 1.3739 3T 1T
R12 41.275 1.6250 41.266 1.6246 41.291 1.6256 41.275 1.6250 0 0 41.263 1.6245 41.247 1.6239 28T 11T
R14 47.625 1.8750 47.616 1.8746 47.641 1.8756 47.625 1.8750 47.613 1.8745 47.597 1.8739
R16 50.800 2.0000 50.789 1.9996 50.819 2.0007 50.800 2.0000 50.786 1.9994 50.767 1.9987
R18 53.975 2.1250 53.964 2.1246 53.994 2.1257 53.975 2.1250 53.961 2.1244 53.942 2.1237
R20 57.150 2.2500 57.139 2.2496 57.169 2.2507 57.150 2.2500 57.136 2.2494 57.117 2.2487
R24 66.675 2.6250 66.664 2.6246 66.694 2.6257 66.675 2.6250 30L 11L 66.661 2.6244 66.642 2.6237 3T 2T
XLS1³|₈ 65.088 2.5625 65.077 2.5621 65.107 2.5632 65.088 2.5625 0 0 65.074 2.5619 65.055 2.5612 33T 13T
XLS1¹|₂ 68.263 2.6875 68.252 2.6871 68.282 2.6882 68.263 2.6875 68.249 2.6869 68.230 2.6862
XLS1⁵|₈ 73.025 2.8750 73.014 2.8746 73.044 2.8757 73.025 2.8750 73.011 2.8744 72.992 2.8737
XLS1³|₄ 76.200 3.0000 76.189 2.9996 76.219 3.0007 76.200 3.0000 76.186 2.9994 76.167 2.9987
XLS1⁷|₈ 80.963 3.1875 80.950 3.1870 80.985 3.1884 80.963 3.1875 80.947 3.1869 80.925 3.1860
XLS2 84.138 3.3125 84.125 3.3120 84.160 3.3134 84.138 3.3125 84.122 3.3119 84.100 3.3110
XLS2¹|₈ 87.313 3.4375 87.300 3.4370 87.335 3.4384 87.313 3.4375 35L 14L 87.297 3.4369 87.275 3.4360 3T 1T
XLS2¹|₄ 90.488 3.5625 90.475 3.5620 90.510 3.5634 90.488 3.5625 0 0 90.472 3.5619 90.450 3.5610 38T 15T
XLS2¹|₂ 98.425 3.8750 98.412 3.8745 98.447 3.8759 98.425 3.8750 98.409 3.8744 98.387 3.8735
XLS2⁵|₈ 104.775 4.1250 104.762 4.1245 104.997 4.1259 104.775 4.1250 104.759 4.1244 104.737 4.1235
XLS2³|₄ 104.775 4.1250 104.762 4.1245 104.997 4.1259 104.775 4.1250 104.759 4.1244 104.737 4.1235
XLS3 114.300 4.5000 114.287 4.4995 114.322 4.5009 114.300 4.5000 114.284 4.4994 114.262 4.4985
XLS3¹|₄ 120.650 4.7500 120.635 4.7494 120.675 4.7510 120.650 4.7500 40L 16L 120.630 4.7492 120.605 4.7482 5T 2T
XLS3¹|₂ 127.000 5.0000 126.985 4.9994 127.025 5.0010 127.000 5.0000 0 0 126.980 4.9992 126.955 4.9982 45T 18T
XLS3³|₄ 133.350 5.2500 133.335 5.2494 133.375 5.2510 133.350 5.2500 133.330 5.2492 133.305 5.2482
XLS4¹|₄ 152.400 6.0000 152.382 5.9993 152.425 6.0010 152.400 6.0000 152.380 5.9992 152.355 5.9981
XLS4¹|₂ 158.750 6.2500 158.732 6.2493 158.775 6.2510 158.750 6.2500 43L 17L 158.730 6.2492 158.704 6.2481 2T 1T
XLS4³|₄ 165.100 6.5000 165.082 6.4993 165.125 6.5010 165.100 6.5000 0 0 165.080 6.4992 165.055 6.4981 45T 19T
XLS5 177.800 7.0000 177.782 6.9993 177.825 7.0010 177.800 7.0000 177.780 6.9992 177.755 6.9981
XLS5¹|₂ 190.500 7.5000 190.480 7.4992 190.529 7.5011 190.500 7.5000 190.478 7.4991 190.449 7.4980
XLS6 203.200 8.0000 203.180 7.9992 203.229 8.0011 203.200 8.0000 203.178 7.9991 203.149 7.9980
XLS6¹|₄ 215.900 8.5000 215.880 8.4992 215.929 8.5011 215.900 8.5000 49L 19L 215.878 8.4991 215.849 8.4980 2T 1T
XLS6¹|₂ 222.250 8.7500 222.230 8.7492 222.279 8.7511 222.250 8.7500 0 0 222.228 8.7491 222.199 8.7480 51T 20T
XLS7 241.300 9.5000 214.280 9.4992 214.329 9.5011 241.300 9.5000 214.278 9.4991 241.249 9.4980
XLS7¹|₄ 247.650 9.7500 247.630 9.7492 247.679 9.7511 247.650 9.7500 247.628 9.7492 247.599 9.7480
XLS7³|₄ 266.700 10.5000 266.675 10.4990 266.732 10.5013 266.700 10.5000 266.675 10.4990 266.643 10.4978
XLS8 273.051 10.7500 273.026 10.7490 273.083 10.7513 273.051 10.7500 57L 23L 273.026 10.7490 272.994 10.7478 0 0
XLS8¹|₄ 279.401 11.0000 279.376 10.9990 279.433 11.0013 279.401 11.0000 0 0 279.376 10.9990 279.334 10.9978 57T 22T
XLS8¹|₂ 292.101 11.5000 292.076 11.4990 292.133 11.5013 292.101 11.5000 292.076 11.4990 292.044 11.4978
XLS9 304.801 12.0000 304.776 11.9990 304.833 12.0013 304.801 12.0000 304.776 11.9990 304.744 11.9978
XLS10 336.551 13.2500 336.523 13.2489 336.587 13.2514 336.551 13.2500 64L 25L 336.525 13.2490 336.489 13.2474 2L 1L
0 0 62T 26T
For aluminum or other soft metal housings make bore limits same as bearing O.D. limits.
257
Shaft Limits—ABEC-5 MRC Bearing Services
Bearing Bore Diameter Shaft Rotating Bearing Bore Diameter Shaft Rotating
Max Min Shaft Diameter Fit Max Min Shaft Diameter Fit
mm Max Min mm Max Min
.001 .0001 .001 .0001
mm in mm in mm in mm in mm in mm in mm in mm in mm in mm in
4 4 0.1575 3.995 0.1573 4.005 0.1577 4 0.1575 0 0 R2 3.175 0.1250 3.170 0.1248 3.180 0.1252 3.175 0.1250
5 5 0.1969 4.995 0.1967 5.005 0.1971 5 0.1969 10T 4T R2A 3.175 0.1250 3.170 0.1248 3.180 0.1252 3.175 0.1250 0 0
6 6 0.2362 5.995 0.2360 6.005 0.2364 6 0.2362 R3 4.763 0.1875 4.758 0.1873 4.767 0.1877 4.763 0.1875 10T 4T
R4 6.350 0.2500 6.345 0.2498 6.355 0.2502 6.350 0.2500
7 7 0.2756 6.995 0.2754 7.005 0.2758 7 0.2756 R4A 6.350 0.2500 6.345 0.2498 6.355 0.2502 6.350 0.2500
8 8 0.3150 7.995 0.3148 8.005 0.3152 8 0.3150 0 0
9 9 0.3543 8.995 0.3541 9.005 0.3545 9 0.3543 10T 4T R6 9.525 0.3750 9.520 0.3748 9.580 0.3752 9.525 0.3750
10 10 0.3937 9.995 0.3935 10.005 0.3939 10 0.3937 R8 12.700 0.5000 12.695 0.4998 12.705 0.5002 12.700 0.5000 0 0
R10 15.875 0.6250 15.870 0.6248 15.880 0.6252 15.875 0.6250 10T 4T
12 12 0.4724 11.995 0.4722 12.005 0.4726 12 0.4724 0 0
15 15 0.5906 14.995 0.5904 15.005 0.5908 15 0.5906 10T 4T R12 19.050 0.7500 19.044 0.7498 19.055 0.7502 19.050 0.7500
17 17 0.6693 16.995 0.6691 17.005 0.6695 17 0.6693 R14 22.225 0.8750 22.219 0.8748 22.230 0.8752 22.225 0.8750 0 0
R16 25.400 1.0000 25.394 0.9998 25.405 1.0002 25.400 1.0000 11T 4T
20 20 0.7874 19.994 0.7872 20.005 0.7876 20 0.7874 0 0 R18 28.575 1.1250 28.769 1.1248 28.580 1.1252 28.575 1.1250
25 25 0.9843 24.994 0.9841 25.005 0.9845 25 0.9843 11T 4T
30 30 1.1811 29.994 1.1809 30.005 1.1813 30 1.1811 R20 31.750 1.2500 31.742 1.2497 31.755 1.2502 31.750 1.2500
R24 38.100 1.5000 38.092 1.4997 38.105 1.5002 38.100 1.5000
35 35 1.3780 34.992 1.3777 35.005 1.3782 35 1.3780 XLS1³|₈ 34.925 1.3750 34.917 1.3747 34.930 1.3752 34.925 1.3750 0 0
40 40 1.5748 39.992 1.5745 40.005 1.5750 40 1.5748 0 0 XLS1¹|₂ 38.100 1.5000 38.092 1.4997 38.105 1.5002 38.100 1.5000 13T 5T
45 45 1.7717 44.992 1.7714 45.005 1.7719 45 1.7717 13T 5T XLS1⁵|₈ 41.275 1.6250 41.267 1.6247 41.280 1.6252 41.275 1.6250
50 50 1.9685 49.992 1.9682 50.005 1.9687 50 1.9685 XLS1³|₄ 44.450 1.7500 44.442 1.7497 44.455 1.7502 44.450 1.7500
XLS1⁷|₈ 47.625 1.8750 47.617 1.8747 47.630 1.8752 47.625 1.8750
55 55 2.1654 54.991 2.1650 55.008 2.1657 55 2.1654
60 60 2.3622 59.991 2.3618 60.008 2.3625 60 2.3622 XLS2 50.800 2.0000 50.791 1.9996 50.808 2.0003 50.800 2.0000
65 65 2.5591 64.991 2.5587 65.008 2.5594 65 2.5591 0 0 XLS2¹|₈ 53.975 2.1250 53.966 2.1246 53.983 2.1253 53.975 2.1250
70 70 2.7559 69.991 2.7555 70.008 2.7562 70 2.7559 17T 7T XLS2¹|₄ 57.150 2.2500 57.141 2.2496 57.158 2.2503 57.150 2.2500 0 0
75 75 2.9528 74.991 2.9524 75.008 2.9531 75 2.9528 XLS2¹|₂ 63.500 2.5000 63.491 2.4996 63.508 2.5003 63.500 2.5000 17T 7T
80 80 3.1496 79.991 3.1492 80.008 3.1499 80 3.1496 XLS2⁵|₈ 66.675 2.6250 66.666 2.6246 66.683 2.6253 66.675 2.6250
XLS2³|₄ 69.850 2.7500 69.841 2.7496 69.858 2.7503 69.850 2.7500
85 85 3.3465 84.990 3.3461 85.008 3.3468 85 3.3465 XLS3 76.200 3.0000 76.191 2.9996 76.208 3.0003 76.200 3.0000
90 90 3.5433 89.990 3.5429 90.008 3.5436 90 3.5433
95 95 3.7402 94.990 3.7398 95.008 3.7405 95 3.7402 0 0 XLS3¹|₄ 82.550 3.2500 82.540 3.2496 82.558 3.2503 82.550 3.2500
100 100 3.9370 99.990 3.9366 100.008 3.9373 100 3.9370 18T 7T XLS3¹|₂ 88.900 3.5000 88.890 3.4996 88.908 3.5003 88.900 3.5000 0 0
105 105 4.1339 104.990 4.1335 105.008 4.1342 105 4.1339 XLS3³|₄ 95.250 3.7500 95.240 3.7496 95.258 3.7503 95.250 3.7500 18T 7T
110 110 4.3307 109.990 4.3303 110.008 4.3310 110 4.3307 XLS4¹|₄ 107.950 4.2500 107.940 4.2496 107.958 4.2503 107.950 4.2500
115 115 4.5276 114.990 4.5272 115.008 4.5279 115 4.5276 XLS4¹|₂ 114.300 4.5000 114.290 4.4996 114.808 4.5003 114.300 4.5000
120 120 4.7244 119.990 4.7240 120.008 4.7247 120 4.7244
XLS4³|₄ 120.650 4.7500 120.637 4.7495 120.660 4.7504 120.650 4.7500
125 125 4.9213 124.987 4.9208 125.010 4.9217 125 4.9213 XLS5 127.000 5.0000 126.987 4.9995 127.010 5.0004 127.000 5.0000
130 130 5.1181 129.987 5.1176 130.010 5.1185 130 5.1181 XLS5¹|₂ 139.700 5.5000 139.687 5.4995 139.710 5.5004 139.700 5.5000 0 0
140 140 5.5118 139.987 5.5113 140.010 5.5122 140 5.5118 0 0 XLS6 152.400 6.0000 152.387 5.9995 152.410 6.0004 152.400 6.0000 23T 9T
150 150 5.9055 149.987 5.9050 150.010 5.9059 150 5.9055 23T 9T XLS6¹|₄ 158.750 6.2500 158.737 6.2495 158.760 6.2504 158.750 6.2500
160 160 6.2992 159.987 6.2987 160.010 6.2996 160 6.2992 XLS6¹|₂ 165.100 6.5000 165.087 6.4995 165.110 6.5004 165.100 6.5000
170 170 6.6929 169.987 6.6924 170.010 6.6933 170 6.6929 XLS7 177.800 7.0000 177.787 6.9995 177.810 7.0004 177.800 7.0000
180 180 7.0866 179.987 7.0861 180.010 7.0870 180 7.0866
XLS7¹|₄ 184.150 7.2500 184.135 7.2494 184.163 7.2505 184.150 7.2500
190 190 7.4803 189.985 7.4797 190.013 7.4808 190 7.4803 XLS7³|₄ 196.850 7.7500 196.835 7.7494 196.863 7.7505 196.850 7.7500
200 200 7.8740 199.985 7.8724 200.013 7.8745 200 7.8740 XLS8 203.200 8.0000 203.185 7.9994 203.213 8.0005 203.200 8.0000 0 0
210 210 8.2677 209.985 8.2671 210.013 8.2682 210 8.2677 0 0 XLS8¹|₄ 209.950 8.2500 209.935 8.2494 209.963 8.2505 209.950 8.2500 28T 11T
220 220 8.6614 219.985 8.6608 220.013 8.6619 220 8.6614 28T 11T XLS8¹|₂ 215.900 8.5000 215.885 8.4994 215.913 8.5005 215.900 8.5000
230 230 9.0551 229.985 9.0545 230.013 9.0556 230 9.0551 XLS9 228.600 9.0000 228.585 8.9994 228.613 9.0005 228.600 9.0000
240 240 9.4488 239.985 9.4482 240.013 9.4493 240 9.4488
250 250 9.8425 249.985 9.8419 250.013 9.8430 250 9.8425 XLS10 254.000 10.0000 253.982 9.9993 254.013 10.0005 254.000 10.0000 0 0
31T 12T
260 260 10.2362 259.982 10.2355 260.013 10.2367 260 10.2362 0 0
280 280 11.0236 279.982 11.0229 280.013 11.0241 280 11.0236 31T 12T
300 300 11.8110 299.982 11.8103 300.013 11.8115 300 11.8110
258
Housing Bore Limits—ABEC-5
Bearing Outside Diameter Housing Stationary Bearing Outside Diameter Housing Stationary
Max Min Housing Bore Fit Max Min Housing Bore Fit
mm Max Min mm Max Min
.001 .0001 .001 .0001
mm in mm in mm in mm in mm in mm in mm in mm in mm in mm in
16 16 0.6299 15.995 0.6297 16.008 0.6302 16 0.6299 13L 5L R2 9.525 0.3750 9.520 0.3748 9.533 0.3753 9.525 0.3750
0 0 R2A 12.700 0.5000 12.695 0.4998 12.708 0.5003 12.700 0.5000 13L 5L
19 19 0.7480 18.994 0.7478 19.008 0.7483 19 0.7480 R3 12.708 0.5000 12.695 0.4998 12.700 0.5003 12.700 0.5000 0 0
21 21 .08268 20.994 0.8266 21.008 0.8271 21 0.8268 R4 15.875 0.6250 15.870 0.6248 15.883 0.6253 15.875 0.6250
22 22 0.8661 21.994 0.8689 22.008 0.8664 22 0.8661 14L 5L
24 24 0.9449 23.994 0.9447 24.008 0.9452 24 0.9449 0 0 R4A 19.050 0.7500 19.044 0.7498 19.058 0.7503 19.050 0.7500 14L 5L
26 26 1.0236 25.994 1.0234 26.008 1.0239 26 1.0236 R6 22.225 0.8750 22.219 0.8748 22.283 0.8753 22.225 0.8750 0 0
28 28 1.1024 27.994 1.1022 28.008 1.1027 28 1.1024 R8 28.575 1.1250 28.569 1.1248 28.583 1.1253 28.575 1.1250
30 30 1.1811 29.994 1.1809 30.008 1.1814 30 1.1811
32 32 1.2598 31.993 1.2595 32.008 1.2601 32 1.2598 R10 34.925 1.3750 34.918 1.3747 34.933 1.3753 34.925 1.3750 15L 6L
35 35 1.3780 34.993 1.3777 35.008 1.3783 35 1.3780 R12 41.275 1.6250 41.268 1.6247 41.283 1.6253 41.275 1.6250 0 0
37 37 1.4567 36.993 1.4564 37.008 1.4570 37 1.4567 15L 6L R14 47.625 1.8750 47.618 1.8747 47.633 1.8753 47.625 1.8750
40 40 1.5748 39.993 1.5745 40.008 1.5751 40 1.5748 0 0
42 42 1.6535 41.993 1.6532 42.008 1.6538 42 1.6535 R16 50.800 2.0000 50.791 1.9996 50.808 2.0003 50.800 2.0000
47 47 1.8504 46.993 1.8501 47.008 1.8507 47 1.8504 R18 53.975 2.1250 53.966 2.1246 53.983 2.1253 53.975 2.1250
52 52 2.0472 51.991 2.0468 52.008 2.0475 52 2.0572 R20 57.150 2.2500 57.141 2.2496 57.158 2.2503 57.150 2.2500 17L 7L
55 55 2.1654 54.991 2.1650 55.008 2.1657 55 2.1654 R24 66.675 2.6250 66.666 2.6246 66.683 2.6253 66.675 2.6250 0 0
58 58 2.2835 57.991 2.2831 58.008 2.2838 58 2.2835 XLS1³|₈ 65.088 2.5625 65.079 2.5621 65.096 2.5628 65.088 2.5625
62 62 2.4409 61.991 2.4405 62.008 2.4412 62 2.4409 XLS1¹|₂ 68.263 2.6875 68.254 2.6871 68.271 2.6878 68.263 2.6875
65 65 2.5591 64.991 2.5587 65.008 2.5594 65 2.5591 17L 7L XLS1⁵|₈ 73.025 2.8750 73.016 2.8746 73.033 2.8753 73.025 2.8750
68 68 2.6772 67.991 2.6768 68.008 2.6775 68 2.6772 0 0 XLS1³|₄ 76.200 3.0000 76.191 2.9996 76.203 3.0003 76.200 3.0000
70 70 2.7559 69.991 2.7555 70.008 2.7562 70 2.7559
72 72 2.8346 71.991 2.8342 72.008 2.8349 72 2.8346 XLS1⁷|₈ 80.963 3.1875 80.953 3.1871 80.973 3.1879 80.963 3.1875
75 75 2.9528 74.991 2.9524 75.008 2.9531 75 2.9528 XLS2 84.138 3.3125 84.128 3.3121 84.148 3.3129 84.138 3.3125
78 78 3.0709 77.991 3.0705 78.008 3.0712 78 3.0709 XLS2¹|₈ 87.313 3.4375 87.303 3.4371 87.323 3.4379 87.313 3.4375
80 80 3.1496 79.991 3.1492 80.008 3.1499 80 3.1496 XLS2¹|₄ 90.488 3.5625 90.478 3.5621 90.498 3.5629 90.488 3.5625 20L 8L
85 85 3.3465 84.990 3.3461 85.010 3.3469 85 3.3465 XLS2¹|₂ 98.425 3.8750 98.415 3.8746 98.435 3.8754 98.425 3.8750 0 0
90 90 3.5433 89.990 3.5429 90.010 3.5437 90 3.5433 XLS2⁵|₈ 104.775 4.1250 104.765 4.1246 104.785 4.1254 104.775 4.1250
95 95 3.7402 94.990 3.7398 95.010 3.7406 95 3.7402 XLS2³|₄ 104.775 4.1250 104.765 4.1246 104.785 4.1254 104.775 4.1250
100 100 3.9370 99.990 3.9366 100.010 3.9374 100 3.9370 20L 8L XLS3 114.300 4.5000 114.290 4.4996 114.310 4.5004 114.300 4.5000
105 105 4.1339 104.990 4.1335 105.010 4.1343 105 4.1339 0 0
110 110 4.3307 109.990 4.3303 110.010 4.3311 110 4.3307 XLS3¹|₄ 120.650 4.7500 120.639 4.7496 120.663 4.7505 120.650 4.7500 24L 9L
115 115 4.5276 114.990 4.5722 115.010 4.5280 115 4.5276 XLS3¹|₂ 127.000 5.0000 126.989 4.9996 127.013 5.0005 127.000 5.0000 0 0
120 120 4.7244 119.990 4.7240 120.010 4.7248 120 4.7244 XLS3³|₄ 133.350 5.2500 133.339 5.2496 133.363 5.2505 133.350 5.2500
125 125 4.9213 124.989 4.9209 125.013 4.9218 125 4.9213
130 130 5.1181 129.989 5.1177 130.013 5.1186 130 5.1181 XLS4¹|₄ 152.400 6.0000 152.387 5.9995 152.413 6.0005 152.400 6.0000
135 135 5.3150 134.989 5.3146 135.013 5.3155 135 5.3150 24L 9L XLS4¹|₂ 158.750 6.2500 158.737 6.2495 158.763 6.2505 158.750 6.2500 26L 10L
140 140 5.5118 139.989 5.5114 140.013 5.5123 140 5.5118 0 0 XLS4³|₄ 165.100 6.5000 165.087 6.4995 165.113 6.5005 165.100 6.5000 0 0
145 145 5.7087 144.989 5.7083 145.013 5.7092 145 5.7087 XLS5 177.800 7.0000 177.787 6.9995 177.813 7.0005 177.800 7.0000
150 150 5.9055 149.989 5.9051 150.013 5.9060 150 5.9055
160 160 6.2992 159.987 6.2987 160.013 6.2997 160 6.2992 XLS5¹|₂ 190.500 7.5000 190.485 7.4994 190.515 7.5006 190.500 7.5000
165 165 6.4961 164.987 6.4956 165.013 6.4966 165 6.4961 26L 10L XLS6 203.200 8.0000 203.185 7.9994 203.215 8.0006 203.200 8.0000
170 170 6.6929 169.987 6.6924 170.013 6.6934 170 6.6929 0 0 XLS6¹|₄ 215.900 8.5000 215.885 8.4994 215.915 8.5006 215.900 8.5000 30L 12L
175 175 6.8898 174.987 6.8893 175.013 6.8903 175 6.8898 XLS6¹|₂ 222.250 8.7500 222.235 8.7494 222.265 8.7506 222.250 8.7500 0 0
180 180 7.0866 179.967 7.0861 180.013 7.0871 180 7.0866 XLS7 241.300 9.5000 241.285 9.4994 241.315 9.5006 241.300 9.5000
190 190 7.4803 189.985 7.4797 190.015 7.4809 190 7.4803 XLS7¹|₄ 247.650 9.7500 247.635 9.7494 247.665 9.7506 247.650 9.7500
200 200 7.8740 199.985 7.8734 200.015 7.8746 200 7.8740
205 205 8.0709 204.985 8.0703 205.015 8.0715 205 8.0709 XLS7³|₄ 266.700 10.5000 266.68210.4993 266.715 10.5006 266.700 10.5000
210 210 8.2677 209.985 8.2671 210.015 8.2683 210 8.2677 XLS8 273.051 10.7500 273.03310.7493 273.066 10.7506 273.051 10.7500 33L 13L
215 215 8.4646 214.985 8.4640 215.015 8.4652 215 8.4646 30L 12L XLS8¹|₄ 279.401 11.0000 279.38310.9993 279.416 11.0006 279.401 11.0000 0 0
220 220 8.6614 219.985 8.6608 220.015 8.6620 220 8.6614 0 0 XLS8¹|₂ 292.101 11.5000 292.08311.4993 292.116 11.5006 292.101 11.5000
225 225 8.8583 224.985 8.8577 225.015 8.8589 225 8.8583 XLS9 304.801 12.0000 304.78311.9993 304.816 12.0006 304.801 12.0000
230 230 9.0551 229.985 9.0545 230.015 9.0557 230 9.0551
235 235 9.2520 234.985 9.2514 235.015 9.2526 235 9.2520 XLS10 336.551 13.2500 336.53113.2492 336.569 13.2507 336.551 13.2500 38L 15L
240 240 9.4488 239.985 9.4482 240.015 9.4494 240 9.4488 0 0
250 250 9.8425 249.985 9.8419 250.015 9.8431 250 9.8425
For aluminum or other soft metal housings, make bore limits same as O.D. limits of
260 260 10.2362 259.982 10.2355 260.015 10.2368 260 10.2362
265 265 10.4331 264.982 10.4324 265.015 10.4337 265 10.4331 bearing.
270 270 10.6299 269.982 10.6292 270.015 10.6302 270 10.6299
280 280 11.0236 279.982 11.0229 280.015 11.0242 280 11.0236 33L 13L
290 290 11.4173 289.982 11.4166 290.015 11.4179 290 11.4173 0 0
300 300 11.8110 299.982 11.8103 300.015 11.8116 300 11.8110
310 310 12.2047 309.982 12.2040 310.015 12.2053 310 12.2047
320 320 12.5984 319.980 12.5976 320.018 12.5991 320 12.5984
340 340 13.3858 339.980 13.3850 340.018 13.3865 340 13.3858
350 350 13.7795 349.980 13.7787 350.018 13.7802 350 13.7795
360 360 14.1732 359.980 14.1724 360.018 14.1739 360 14.1732 38L 15L
370 370 14.5669 369.980 14.5661 370.018 14.5676 370 14.5669 0 0
380 380 14.9606 379.980 14.9598 380.018 14.9613 380 14.9606
390 390 15.3543 389.980 15.3535 390.018 15.3550 390 15.3543
400 400 15.7480 399.980 15.7472 400.018 15.7487 400 15.7480
410 410 16.1417 409.977 16.1408 410.020 16.1425 410 16.1417
420 420 16.5354 419.977 16.5345 420.020 16.5362 420 16.5354
430 430 16.9291 429.977 16.9282 430.020 16.9299 430 16.9291 43L 17L
440 440 17.3228 439.977 17.3219 440.020 17.3236 440 17.3228 0 0
460 460 18.1102 459.977 18.1093 460.020 18.1110 460 18.1102
480 480 18.8976 479.977 18.8967 480.020 18.8984 480 18.8976
500 500 19.6850 499.977 19.6841 500.020 19.6858 500 19.6850
520 520 20.4724 519.972 20.4713 520.025 20.4734 520 20.4224
540 540 21.2598 539.972 21.2587 540.025 21.2608 540 21.2598
560 560 22.0472 559.972 22.0461 560.025 22.0482 560 22.0472 53L 21L
580 580 22.8346 579.972 22.8335 580.025 22.8356 580 22.8346 0 0
600 600 23.6220 599.972 23.6209 600.025 23.6230 600 23.6220
620 620 24.4094 619.972 24.4083 620.025 24.4104 620 24.4094
For aluminum or other soft metal housings, make bore limits same as O.D. limits of
bearing.
259
Shaft Limits—ABEC-7 MRC Bearing Services
Bearing Bore Diameter Shaft Rotating Bearing Bore Diameter Shaft Rotating
Max Min Shaft Diameter Fit Max Min Shaft Diameter Fit
mm Max Min mm Max Min
.001 .0001 .001 .0001
mm in mm in mm in mm in mm in mm in mm in mm in mm in mm in
4 4 0.1575 3.996 0.15735 4.005 0.1577 4 0.1575 0 0 R2 3.175 0.1250 3.171 0.12485 3.180 0.1252 3.175 0.1250
5 5 0.1969 4.996 0.19675 5.005 0.1971 5 0.1969 9T 3.5T R2A 3.175 0.1250 3.171 0.12485 3.180 0.1252 3.175 0.1250 0 0
6 6 0.2362 5.996 0.23605 6.005 0.2364 6 0.2362 R3 4.763 0.1875 4.759 0.18735 4.767 0.1877 4.763 0.1875 9T 3.5T
R4 6.350 0.2500 6.346 0.24985 6.355 0.2502 6.350 0.2500
7 7 0.2756 6.996 0.27545 7.005 0.2758 7 0.2756 R4A 6.350 0.2500 6.346 0.24985 6.355 0.2502 6.350 0.2500
8 8 0.3150 7.996 0.31485 8.005 0.3152 8 0.3150 0 0
9 9 0.3543 8.996 0.35415 9.005 0.3545 9 0.3543 9T 3.5T R6 9.525 0.3750 9.521 0.37485 9.530 0.3752 9.525 0.3750 0 0
10 10 0.3937 9.996 0.39355 10.005 0.3939 10 0.3937 R8 12.700 0.5000 12.696 0.49985 12.705 0.5002 12.700 0.5000 9T 3.5T
R10 15.875 0.6250 15.871 0.62485 15.880 0.6252 15.875 0.6250
12 12 0.4724 11.996 0.47225 12.005 0.4726 12 0.4724 0 0
15 15 0.5906 14.996 0.59045 15.005 0.5908 15 0.5906 9T 3.5T R12 19.050 0.7500 19.045 0.7498 19.055 0.7502 19.050 0.7500
17 17 0.6693 16.996 0.66915 17.005 0.6695 17 0.6693 R14 22.225 0.8750 22.220 0.8748 22.230 0.8752 22.225 0.8750 0 0
R16 25.400 1.0000 25.395 0.9998 25.405 1.0002 25.400 1.0000 10T 4T
20 20 0.7874 19.995 0.7872 20.005 0.7876 20 0.7874 0 0 R18 28.575 1.1250 28.570 1.1248 28.580 1.1252 28.575 1.1250
25 25 0.9843 24.995 0.9841 25.005 0.9845 25 0.9843 10T 4T
30 30 1.1811 29.995 1.1809 30.005 1.1813 30 1.1811 R20 31.750 1.2500 31.744 1.24975 31.755 1.2502 31.750 1.2500
R24 38.100 1.5000 38.094 1.49975 38.105 1.5002 38.100 1.5000
35 35 1.3780 34.994 1.37775 35.005 1.3782 35 1.3780 XLS1³|₈ 34.925 1.3750 34.919 1.37475 34.930 1.3752 34.925 1.3750 0 0
40 40 1.5748 39.994 1.57455 40.005 1.5750 40 1.5748 0 0 XLS1¹|₂ 38.100 1.5000 38.094 1.49975 38.105 1.5002 38.100 1.5000 11T 4.5T
45 45 1.7717 44.994 1.77145 45.005 1.7719 45 1.7717 11T 4.5T XLS1⁵|₈ 41.275 1.6250 41.269 1.62475 41.280 1.6252 41.275 1.6250
50 50 1.9685 49.994 1.96825 50.005 1.9687 50 1.9685 XLS1³|₄ 44.450 1.7500 44.444 1.74975 44.455 1.7502 44.450 1.7500
XLS1⁷|₈ 47.625 1.8750 47.619 1.87475 47.630 1.8752 47.625 1.8750
55 55 2.1654 54.993 2.1651 55.008 2.1657 55 2.1654
60 60 2.3622 59.993 2.3619 60.008 2.3625 60 2.3622 XLS2 50.800 2.0000 50.793 1.9997 50.808 2.0003 50.800 2.0000
65 65 2.5591 64.993 2.5588 65.008 2.5594 65 2.5591 0 0 XLS2¹|₈ 53.975 2.1250 53.968 2.1247 53.983 2.1253 53.975 2.1250
70 70 2.7559 69.993 2.7556 70.008 2.7562 70 2.7559 15T 6T XLS2¹|₄ 57.150 2.2500 57.143 2.2497 57.158 2.2503 57.150 2.2500 0 0
75 75 2.9528 74.993 2.9525 75.008 2.9531 75 2.9528 XLS2¹|₂ 63.500 2.5000 63.493 2.4997 63.508 2.5003 63.500 2.5000 15T 6T
80 80 3.1496 79.993 3.1493 80.008 3.1499 80 3.1496 XLS2⁵|₈ 66.675 2.6250 66.668 2.6247 66.683 2.6253 66.675 2.6250
XLS2³|₄ 69.850 2.7500 69.843 2.7497 69.858 2.7503 69.850 2.7500
85 85 3.3465 84.992 3.3462 85.008 3.3468 85 3.3465 XLS3 76.200 3.0000 76.193 2.9997 76.208 3.0003 76.200 3.0000
90 90 3.5433 89.992 3.5430 90.008 3.5436 90 3.5433
95 95 3.7402 94.992 3.7399 95.008 3.7405 95 3.7402 0 0 XLS3¹|₄ 82.550 3.2500 82.542 3.2497 82.558 3.2503 82.550 3.2500
100 100 3.9370 99.992 3.9367 100.008 3.9373 100 3.9370 16T 6T XLS3¹|₂ 88.900 3.5000 88.892 3.4997 88.908 3.5003 88.900 3.5000 0 0
105 105 4.1339 104.992 4.1336 105.008 4.1342 105 4.1339 XLS3³|₄ 95.250 3.7500 95.242 3.7497 95.258 3.7503 95.250 3.7500 16T 6T
110 110 4.3307 109.992 4.3304 110.008 4.3310 110 4.3307 XLS4¹|₄ 107.950 4.2500 107.942 4.2497 107.958 4.2503 107.950 4.2500
115 115 4.5276 114.992 4.5273 115.008 4.5279 115 4.5276 XLS4¹|₂ 114.300 4.5000 114.292 4.4997 114.308 4.5003 114.300 4.5000
120 120 4.7244 119.992 4.7241 120.008 4.7247 120 4.7244
XLS4³|₄ 120.650 4.7500 120.640 4.7496 120.660 4.7504 120.650 4.7500
125 125 4.9213 124.990 4.9209 125.010 4.9217 125 4.9213 XLS5 127.000 5.0000 126.990 4.9996 127.010 5.0004 127.000 5.0000
130 130 5.1181 129.990 5.1177 130.010 5.1185 130 5.1181 XLS5¹|₂ 139.700 5.5000 139.690 5.4996 139.710 5.5004 139.700 5.5000 0 0
140 140 5.5118 139.990 5.5114 140.010 5.5122 140 5.5118 0 0 XLS6 152.400 6.0000 152.390 5.9996 152.410 6.0004 152.400 6.0000 20T 8T
150 150 5.9055 149.990 5.9051 150.010 5.9059 150 5.9055 20T 8T XLS6¹|₄ 158.750 6.2500 158.740 6.2496 158.760 6.2504 158.750 6.2500
160 160 6.2992 159.990 6.2988 160.010 6.2996 160 6.2992 XLS6¹|₂ 165.100 6.5000 165.090 6.4996 165.110 6.5004 165.100 6.5000
170 170 6.6929 169.990 6.6925 170.010 6.6933 170 6.6929 XLS7 177.800 7.0000 177.790 6.9996 177.810 7.0004 177.800 7.0000
180 180 7.0866 179.990 7.0862 180.010 7.0870 180 7.0866
XLS7¹|₄ 184.150 7.2500 184.138 7.24955 184.163 7.2505 184.150 7.2500
190 190 7.4803 189.988 7.47985 190.013 7.4808 190 7.4803 XLS7³|₄ 196.850 7.7500 196.738 7.74955 196.863 7.7505 196.850 7.7500 0 0
200 200 7.8740 199.988 7.87355 200.013 7.8745 200 7.8740 XLS8 203.200 8.0000 203.088 7.99955 203.213 8.0005 203.200 8.0000 25T 9.5T
210 210 8.2677 209.988 8.26725 210.013 8.2682 210 8.2677 0 0 XLS8¹|₄ 209.950 8.2500 209.938 8.24955 209.963 8.2505 209.950 8.2500
220 220 8.6614 219.988 8.66095 220.018 8.6619 220 8.6614 25T 9.5T XLS8¹|₂ 215.900 8.5000 215.888 8.49955 215.913 8.5005 215.900 8.5000
230 230 9.0551 229.988 9.05465 230.013 9.0556 230 9.0551 XLS9 228.600 9.0000 228.588 8.99955 228.613 9.0005 228.600 9.0000
240 240 9.4488 239.988 9.44835 240.013 9.4493 240 9.4488
250 250 9.8425 249.988 9.84205 250.013 9.8430 250 9.8425 XLS10 254.000 10.0000 253.987 9.9995 254.013 10.0005 254.000 10.0000 0 0
26T 10T
260 260 10.2362 259.987 10.2357 260.013 10.2367 260 10.2362 0 0
280 280 11.0236 279.987 11.0231 280.013 11.0241 280 11.0236 26T 10T
300 300 11.8110 299.987 11.8105 300.013 11.8115 300 11.8110
260
Housing Bore Limits—ABEC-7
Bearing Outside Diameter Housing Stationary Bearing Outside Diameter Housing Stationary
Max Min Housing Bore Fit Max Min Housing Bore Fit
mm Max Min mm Max Min
.001 .0001 .001 .0001
mm in mm in mm in mm in mm in mm in mm in mm in mm in mm in
16 16 0.6299 15.996 0.62975 16.008 0.6302 16 0.6299 12L 4.5L R2 9.525 0.3750 9.521 0.37485 9.533 0.3753 9.525 0.3750
0 0 R2A 12.700 0.5000 12.696 0.49985 12.708 0.5003 12.700 0.5000 12L 4.5L
R3 12.700 0.5000 12.696 0.49985 12.708 0.5003 12.700 0.5000 0 0
19 19 0.7480 18.995 0.7478 19.008 0.7483 19 0.7480 R4 15.875 0.6250 15.871 0.62485 15.883 0.6253 15.875 0.6250
21 21 0.8268 20.995 0.8266 21.008 0.8271 21 0.8268
22 22 0.8661 21.995 0.8659 22.008 0.8664 22 0.8661 R4A 19.050 0.7500 19.045 0.7498 19.058 0.7503 19.050 0.7500
24 24 0.9449 23.995 0.9447 24.008 0.9432 24 0.9449 13L 5L R6 22.225 0.8750 22.220 0.8748 22.233 0.8753 22.225 0.8750 13L 5L
26 26 1.0236 25.995 1.0234 26.008 1.0239 26 1.0236 0 0 R8 28.575 1.1250 28.570 1.1248 28.583 1.1253 28.575 1.1250 0 0
28 28 1.1024 27.995 1.1022 28.008 1.1027 28 1.1024
30 30 1.1811 29.995 1.1809 30.008 1.1814 30 1.1811 R10 34.925 1.3750 34.919 1.37475 34.933 1.3753 34.925 1.3750 14L 5.5L
R12 41.275 1.6250 41.269 1.62475 41.283 1.6253 41.275 1.6250 0 0
32 32 1.2598 31.994 1.25955 32.008 1.2601 32 1.2598 R14 47.625 1.8750 47.619 1.87475 47.633 1.8753 47.625 1.8750
35 35 1.3780 34.994 1.37775 35.008 1.3783 35 1.3780
37 37 1.4567 36.994 1.45645 37.008 1.4570 37 1.4567 14L 5.5L R16 50.800 2.0000 50.793 1.9997 50.808 2.0003 50.800 2.0000
40 40 1.5748 39.994 1.57455 40.008 1.5751 40 1.5748 0 0 R18 53.975 2.1250 53.968 2.1247 53.983 2.1253 53.975 2.1250
42 42 1.6535 41.994 1.65325 42.008 1.6538 42 1.6535 R20 57.150 2.2500 57.143 2.2497 57.158 2.2503 57.150 2.2500 15L 6L
47 47 1.8504 46.994 1.85015 47.008 1.8507 47 1.8504 R24 66.675 2.6250 66.668 2.6247 66.683 2.6253 66.675 2.6250 0 0
XLS1³|₈ 65.088 2.5625 65.081 2.5622 65.096 2.5628 65.088 2.5625
52 52 2.0472 51.993 2.0469 52.008 2.0475 52 2.0472 XLS1¹|₂ 68.263 2.6875 68.256 2.6872 68.271 2.6878 68.263 2.6875
55 55 2.1654 54.993 2.1651 55.008 2.1657 55 2.1654 XLS1⁵|₈ 73.025 2.8750 73.018 2.8747 73.033 2.8753 73.025 2.8750
58 58 2.2835 57.993 2.2832 58.008 2.2838 58 2.2835 XLS1³|₄ 76.200 3.0000 76.193 2.9997 76.203 3.0003 76.200 3.0000
62 62 2.4409 61.993 2.4406 62.008 2.4412 62 2.4409
65 65 2.5591 64.993 2.5588 65.008 2.5594 65 2.5591 15L 6L XLS1⁷|₈ 80.963 3.1875 80.955 3.1872 80.973 3.1879 80.963 3.1875
68 68 2.6772 67.993 2.6769 68.008 2.6775 68 2.6772 0 0 XLS2 84.138 3.3125 84.130 3.3122 84.148 3.3129 84.138 3.3125
70 70 2.7559 69.993 2.7556 70.008 2.7562 70 2.7559 XLS2¹|₈ 87.313 3.4375 87.305 3.4372 87.323 3.4379 87.313 3.4375
72 72 2.8346 71.993 2.8343 72.008 2.8349 72 2.8346 XLS2¹|₄ 90.488 3.5625 90.480 3.5622 90.498 3.5629 90.488 3.5625 18L 7L
75 75 2.9528 74.993 2.9525 75.008 2.9531 75 2.9528 XLS2¹|₂ 98.425 3.8750 98.417 3.8747 98.435 3.8754 98.425 3.8750 0 0
78 78 3.0709 77.993 3.0706 78.008 3.0712 78 3.0709 XLS2⁵|₈ 104.775 4.1250 104.767 4.1247 104.785 4.1254 104.775 4.1250
80 80 3.1496 79.993 3.1493 80.008 3.1499 80 3.1496 XLS2³|₄ 104.775 4.1250 104.767 4.1247 104.785 4.1254 104.775 4.1250
XLS3 114.300 4.5000 114.292 4.4997 114.310 4.5004 114.300 4.5000
85 85 3.3465 84.992 3.3462 85.010 3.3469 85 3.3465
90 90 3.5433 89.992 3.5430 90.010 3.5437 90 3.5433 XLS3¹|₄ 120.650 4.7500 120.641 4.74965 120.663 4.7505 120.650 4.7500 22L 8.5L
95 95 3.7402 94.992 3.7399 95.010 3.7406 95 3.7402 XLS3¹|₂ 127.000 5.0000 126.991 4.99965 127.013 5.0005 127.000 5.0000 0 0
100 100 3.9370 99.992 3.9367 100.010 3.9374 100 3.9370 18L 7L XLS3³|₄ 133.350 5.2500 133.341 3.24965 133.365 5.2505 133.350 5.2500
105 105 4.1339 104.992 4.1336 105.010 4.1343 105 4.1339 0 0
110 110 4.3307 109.992 4.3304 110.010 4.3311 110 4.3307 XLS4¹|₄ 152.400 6.0000 152.390 5.9996 152.413 6.0005 152.400 6.0000
115 115 4.5276 114.992 4.5273 115.010 4.5280 115 4.5276 XLS4¹|₂ 158.750 6.2500 158.740 6.2496 158.763 6.2505 158.750 6.2500 23L 9L
120 120 4.7244 119.992 4.7241 120.010 4.7248 120 4.7244 XLS4³|₄ 165.100 6.5000 165.090 6.4996 165.113 6.5005 165.100 6.5000 0 0
XLS5 177.800 7.0000 177.790 6.9996 177.813 7.0005 177.800 7.0000
125 125 4.9213 124.991 4.92095 125.013 4.9218 125 4.9213
130 130 5.1181 129.991 5.11775 130.013 5.1186 130 5.1181 XLS5¹|₂ 190.500 7.5000 190.489 7.49955 190.515 7.5006 190.500 7.5000
135 135 5.3150 134.991 5.31465 135.013 5.3155 135 5.3150 22L 8.5L XLS6 203.200 8.0000 203.189 7.99955 203.215 8.0006 203.200 8.0000
140 140 5.5118 139.991 5.51145 140.013 5.5123 140 5.5118 0 0 XLS6¹|₄ 215.900 8.5000 215.889 8.49955 215.915 8.5006 215.900 8.5000 26L 10.5L
145 145 5.7087 144.991 5.70835 145.013 5.7092 145 5.7087 XLS6¹|₂ 222.250 8.7500 222.239 8.74955 222.265 8.7506 222.250 8.7500 0 0
150 150 5.9055 149.991 5.90515 150.013 5.9060 150 5.9055 XLS7 241.300 9.5000 241.289 9.49955 241.315 9.5006 241.300 9.5000
XLS7¹|₄ 247.650 9.7500 247.639 9.74955 247.665 9.7506 247.650 9.7500
160 160 6.2992 159.990 6.2988 160.013 6.2997 160 6.2992
165 165 6.4961 164.990 6.4957 165.013 6.4966 165 6.4961 XLS7³|₄ 266.700 10.5000 266.687 10.4995 266.715 10.5006 266.700 10.5000
170 170 6.6929 169.990 6.6925 170.013 6.6934 170 6.6929 23L 9L XLS8 273.051 10.7500 273.038 10.7495 273.066 10.7506 273.051 10.7500
175 175 6.8898 174.990 6.8894 175.013 6.8903 175 6.8898 0 0 XLS8¹|₄ 279.401 11.0000 279.388 10.9995 279.416 11.0006 279.401 11.0000 28L 11L
180 180 7.0866 179.990 7.0862 180.013 7.0871 180 7.0866 XLS8¹|₂ 292.101 11.5000 292.088 11.4995 292.116 11.5006 292.101 11.5000 0 0
XLS9 304.801 12.0000 304.788 11.9995 304.816 12.0006 304.801 12.0000
190 190 7.4803 189.989 7.47985 190.015 7.4809 190 7.4803
200 200 7.8740 199.989 7.87355 200.015 7.8746 200 7.8740 XLS10 336.551 13.2500 336.536 13.2494 336.569 13.2507 336.551 13.2500 33L 13L
205 205 8.0709 204.989 8.07045 205.015 8.0715 205 8.0709 0 0
210 210 8.2677 209.989 8.26725 210.015 8.2683 210 8.2677
215 215 8.4646 214.989 8.46415 215.015 8.4652 215 8.4646 26L 10.5L For aluminum or other soft metal housings, make bore limits same as O.D. limits of
220 220 8.6614 219.989 8.66095 220.015 8.6620 220 8.6614 0 0 bearing.
225 225 8.8583 224.989 8.85785 225.015 8.8589 225 8.8583
230 230 9.0551 229.989 9.05465 230.015 9.0557 230 9.0551
235 235 9.2520 234.989 9.25155 235.015 9.2526 235 9.2520
240 240 9.4488 239.989 9.44835 240.015 9.4494 240 9.4488
250 250 9.8425 249.989 9.84205 250.015 9.8431 250 9.8425
261
262
ISO Fits For Solid Steel Shafts
The ISO Shaft Tolerances listed are shown in the tables on pages 264 & 265.
Ball
Bearings
Light and variable loads Conveyors, light loaded gearbox bearings (18) to 100 j6
(P ≤ 0.06C) (100) to 140 k6
Very heavy loads and shock Axleboxes for heavy railway vehicles, traction — n62)
loads with difficult working motors, rolling mills — p62)
conditions (P > 0.12C) — r62)
*Variable external loads, shock loads, and vibratory and unbalanced loads in high-speed machinery cannot be accurately described and are
classified as ‘‘direction of load indeterminate.’’
1) The tolerances in brackets are generally used for metric tapered roller bearings and single-row angular contact ball bearings. May also be
used for other bearing types where speeds are moderate and the effect on internal clearance variation is not significant.
2)
Bearings with radial internal clearance greater than normal may be necessary
3) Not applicable to high precision bearings
263
ISO Fits for Solid Steel Shafts MRC Bearing Services
Shaft Bearing-Seat Diameters (Values in Inches)
Bearing Bore g6 h6 h5 j5 j6 k5
Diameter Fit Fit Fit Fit Fit Fit
in in in in in in
Inches Shaft Dia. 0.0001" Shaft Dia. 0.0001" Shaft Dia. 0.0001" Shaft Dia. 0.0001" Shaft Dia. 0.0001" Shaft Dia. 0.0001"
mm Max Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min.
4 0.1575 0.1572 0.1573 0.1570 0.1575 0.1572 0.1575 0.1573 0.1576 0.1574 0.1577 0.1574 0.1577 0.1575
5 0.1969 0.1966 0.1967 0.1964 5L 0.1969 0.1966 3L 0.1969 0.1967 2L 0.1970 0.1968 1L 0.1971 0.1968 1L 0.1971 0.1969 0T
6 0.2362 0.2359 0.2360 0.2357 1T 0.2362 0.2359 3T 0.2362 0.2360 3T 0.2363 0.2361 4T 0.2364 0.2361 5T 0.2364 0.2362 5T
7 0.2756 0.2753 0.2754 0.2750 0.2756 0.2752 0.2756 0.2754 0.2758 0.2755 0.2759 0.2755 0.2759 0.2756
8 0.3150 0.3147 0.3148 0.3144 6L 0.3150 0.3146 4L 0.3150 0.3148 2L 0.3152 0.3149 1L 0.3153 0.3149 1L 0.3153 0.3150 0T
9 0.3543 0.3540 0.3541 0.3537 1T 0.3543 0.3539 3T 0.3543 0.3541 3T 0.3545 0.3542 5T 0.3546 0.3542 6T 0.3546 0.3543 6T
10 0.3937 0.3934 0.3935 0.3931 0.3937 0.3933 0.3937 0.3935 0.3939 0.3936 0.3940 0.3936 0.3940 0.3937
12 0.4724 0.4721 0.4722 0.4717 0.4724 0.4720 0.4724 0.4721 0.4726 0.4723 0.4727 0.4723 0.4728 0.4724
15 0.5906 0.5903 0.5904 0.5899 7L 0.5906 0.5902 4L 0.5906 0.5903 3L 0.5908 0.5905 1L 0.5909 0.5905 1L 0.5910 0.5906 0T
17 0.6693 0.6690 0.6691 0.6686 1T 0.6693 0.6689 3T 0.6693 0.6690 3T 0.6695 0.6692 5T 0.6696 0.6692 6T 0.6697 0.6693 7T
20 0.7874 0.7870 0.7871 0.7866 0.7874 0.7869 0.7874 0.7870 0.7876 0.7872 0.7878 0.7872 0.7878 0.7875
25 0.9843 0.9839 0.9840 0.9835 8L 0.9843 0.9838 5L 0.9843 0.9839 4L 0.9845 0.9841 2L 0.9847 0.9841 2L 0.9847 0.9844 1T
30 1.1811 1.1807 1.1808 1.1803 1T 1.1811 1.1806 4T 1.1811 1.1807 4T 1.1813 1.1809 6T 1.1815 1.1809 8T 1.1815 1.1812 8T
35 1.3780 1.3775 1.3776 1.3770 1.3780 1.3774 1.3780 1.3776 1.3782 1.3778 1.3784 1.3778 1.3785 1.3781
40 1.5748 1.5743 1.5744 1.5738 10L 1.5748 1.5742 6L 1.5748 1.5744 4L 1.5750 1.5746 2L 1.5752 1.5746 2L 1.5753 1.5749 1T
45 1.7717 1.7712 1.7713 1.7707 1T 1.7717 1.7711 5T 1.7717 1.7713 5T 1.7719 1.7715 7T 1.7721 1.7715 9T 1.7722 1.7718 10T
50 1.9685 1.9680 1.9681 1.9675 1.9685 1.9679 1.9685 1.9681 1.9687 1.9683 1.9689 1.9683 1.9690 1.9686
55 2.1654 2.1648 2.1650 2.1643 2.1654 2.1647 2.1654 2.1649 2.1656 2.1651 2.1659 2.1651 2.1660 2.1655
60 2.3622 2.3616 2.3618 2.3611 2.3622 2.3615 2.3622 2.3617 2.3624 2.3619 2.3627 2.3619 2.3628 2.3623
65 2.5591 2.5585 2.5587 2.5580 11L 2.5591 2.5584 7L 2.5591 2.5586 5L 2.5593 2.5588 3L 2.5596 2.5588 3L 2.5597 2.5592 1T
70 2.7559 2.7553 2.7555 2.7548 2T 2.7559 2.7552 6T 2.7559 2.7554 6T 2.7561 2.7556 8T 2.7564 2.7556 11T 2.7565 2.7560 12T
75 2.9528 2.9522 2.9524 2.9517 2.9528 2.9521 2.9528 2.9523 2.9530 2.9525 2.9533 2.9525 2.9534 2.9529
80 3.1496 3.1490 3.1492 3.1485 3.1496 3.1489 3.1496 3.1491 3.1498 3.1493 3.1501 3.1493 3.1502 3.1497
85 3.3465 3.3457 3.3460 3.3452 3.3465 3.3456 3.3465 3.3459 3.3467 3.3461 3.3470 3.3461 3.3472 3.3466
90 3.5433 3.5425 3.5428 3.5420 3.5433 3.5424 3.5433 3.5427 3.5435 3.5429 3.5438 3.5429 3.5440 3.5434
95 3.7402 3.7394 3.7397 3.7389 3.7402 3.7393 3.7402 3.7396 3.7404 3.7398 3.7407 3.7398 3.7409 3.7403
100 3.9370 3.9362 3.9365 3.9357 13L 3.9370 3.9361 9L 3.9370 3.9364 6L 3.9372 3.9366 4L 3.9375 3.9366 4L 3.9377 3.9371 1T
105 4.1339 4.1331 4.1334 4.1326 3T 4.1339 4.1330 8T 4.1339 4.1333 8T 4.1341 4.1335 10T 4.1344 4.1335 13T 4.1346 4.1340 15T
110 4.3307 4.3299 4.3302 4.3294 4.3307 4.3298 4.3307 4.3301 4.3309 4.3303 4.3312 4.3303 4.3314 4.3308
115 4.5276 4.5268 4.5271 4.5263 4.5276 4.5267 4.5276 4.5270 4.5278 4.5272 4.5281 4.5272 4.5283 4.5277
120 4.7244 4.7236 4.7239 4.7231 4.7244 4.7235 4.7244 4.7238 4.7246 4.7240 4.7249 4.7240 4.7251 4.7245
125 4.9213 4.9203 4.9207 4.9198 4.9213 4.9203 4.9213 4.9206 4.9216 4.9209 4.9219 4.9209 4.9221 4.9214
130 5.1181 5.1171 5.1175 5.1166 5.1181 5.1171 5.1181 5.1174 5.1184 5.1177 5.1187 5.1177 5.1189 5.1182
140 5.5118 5.5108 5.5112 5.5103 5.5118 5.5108 5.5118 5.5111 5.5121 5.5114 5.5124 5.5114 5.5126 5.5119
150 5.9055 5.9045 5.9049 5.9040 15L 5.9055 5.9045 10L 5.9055 5.9048 7L 5.9058 5.9051 4L 5.9061 5.9051 4L 5.9063 5.9056 1T
160 6.2992 6.2982 6.2986 6.2977 4T 6.2992 6.2982 10T 6.2992 6.2985 10T 6.2995 6.2988 13T 6.2998 6.2988 16T 6.3000 6.2993 18T
170 6.6929 6.6919 6.6923 6.6914 6.6929 6.6919 6.6929 6.6922 6.6932 6.6925 6.6935 6.6925 6.6937 6.6930
180 7.0866 7.0856 7.0860 7.0851 7.0866 7.0856 7.0866 7.0859 7.0869 7.0862 7.0872 7.0862 7.0874 7.0867
190 7.4803 7.4791 7.4797 7.4786 7.4803 7.4792 7.4803 7.4795 7.4806 7.4798 7.4809 7.4798 7.4812 7.4805
200 7.8740 7.8728 7.8734 7.8723 17L 7.8740 7.8729 11L 7.8740 7.8732 8L 7.8743 7.3735
5L
7.8746 7.8735
5L
7.8749 7.8742
2T
220 8.6614 8.6602 8.6608 8.6597 6T 8.6614 8.6603 12T 8.6614 8.6606 12T 8.6617 8.6609 15T 8.6620 8.6609 18T 8.6623 8.6616 21T
240 9.4488 9.4476 9.4482 9.4471 9.4488 9.4477 9.4488 9.4480 9.4491 9.4483 9.4494 9.4483 9.4497 9.4490
250 9.8425 9.8413 9.8419 9.8408 9.8425 9.8414 9.8425 9.8417 9.8428 9.8420 9.8431 9.8420 9.8434 9.8427
260 10.2362 10.2348 10.2355 10.2343 10.2362 10.2349 10.2362 10.2353 10.2365 10.2356 10.2368 10.2356 10.2373 10.2364
280 11.0236 11.0222 11.0229 11.0217 19L 11.0236 11.0223 13L 11.0236 11.0225 9L 11.0239 11.0230 6L 11.0242 11.0230 6L 11.0247 11.0238 2T
7T 14T 14T 17T 20T 25T
300 11.8110 11.8096 11.8103 11.8091 11.8110 11.8097 11.8110 11.8101 11.8113 11.8104 11.8116 11.8104 11.8121 11.8112
310 12.2047 12.2033 12.2040 12.2028 12.2047 12.2034 12.2047 12.2038 12.2050 12.2041 12.2053 12.2041 12.2058 12.2049
320 12.5984 12.5968 12.5977 12.5963 12.5984 12.5970 12.5984 12.5974 12.5987 12.5977 12.5991 12.5977 12.5995 12.5986
340 13.3858 13.3842 13.3851 13.3837 13.3858 13.3844 13.3858 13.3848 13.3861 13.3851 13.3865 13.3851 13.3869 13.3860
350 13.7795 13.7779 13.7788 13.7774 21L 13.7795 13.7781 14L 13.7795 13.7785 10L 13.7798 13.7788 7L 13.7802 13.7788 7L 13.7806 13.7797 2T
360 14.1732 14.1716 14.1725 14.1711 9T 14.1732 14.1718 16T 14.1732 14.1722 16T 14.1735 14.1725 19T 14.1739 14.1725 23T 14.1743 14.1734 27T
380 14.9606 14.9590 14.9599 14.9585 14.9606 14.9592 14.9606 14.9596 14.9609 14.9599 14.9613 14.9599 14.9617 14.9608
400 15.7480 15.7464 15.7473 15.7459 15.7480 15.7466 15.7480 15.7470 15.7483 15.7473 15.7487 15.7473 15.7491 15.7482
420 16.5354 16.5336 16.5346 16.5330 16.5354 16.5338 16.5354 16.5343 16.5357 16.5346 16.5362 16.5346 16.5367 16.5356
440 17.3228 17.3210 17.3220 17.3204 17.3228 17.3212 17.3228 17.3217 17.3231 17.3220 17.3236 17.3220 17.3241 17.3230
24L 16L 11L 8L 8L 2T
460 18.1102 18.1084 18.1094 18.1078 10T 18.1102 18.1086 18T 18.1102 18.1091 18T 18.1105 18.1094 21T 18.1110 18.1094 26T 18.1115 18.1104 31T
480 18.8976 18.8958 18.8968 18.8952 18.8976 18.8960 18.8976 18.8965 18.8979 18.8968 18.8984 18.8968 18.8989 18.8978
500 19.6850 19.6832 19.6842 19.6826 19.6850 19.6834 19.6850 19.6839 19.6853 19.6842 19.6858 19.6842 19.6863 19.6852
530 20.8661 20.8641 20.8652 20.8635 20.8661 20.8644 20.8664 20.8652 20.8670 20.8652 20.8673 20.8661
560 22.0472 22.0452 22.0463 22.0446 26L 22.0472 22.0455 17L 22.0475 22.0463 9L 22.0481 22.0463 9L 22.0484 22.0472 0T
600 23.6220 23.6200 23.6211 23.6194 11T 23.6220 23.6203 20T 23.6223 23.6211 23T 23.6229 23.6211 29T 23.6232 23.6220 32T
630 24.8031 24.8011 24.8022 24.8005 24.8031 24.8014 24.8034 24.8022 24.8040 24.8012 24.8043 24.8031
660 25.9843 25.9813 25.9834 25.9814 25.9843 25.9823 25.9847 25.9833 25.9853 25.9833 25.9857 25.9843
670 26.3780 26.3750 26.3771 26.3751 26.3780 26.3760 26.3784 26.3770 26.3790 26.3770 26.3794 26.3780
710 27.9528 27.9498 27.9519 27.9499 29L 27.9528 27.9508 20L 27.9532 27.9518 10L 27.9538 27.9518 10L 27.9542 27.9528 0T
21T 30T 34T 40T 44T
750 29.5276 29.5246 29.5267 29.5247 29.5276 29.5256 29.5280 29.5266 29.5286 29.5266 29.5290 29.5276
780 30.7087 30.7057 30.7078 30.7058 30.7087 30.7067 30.7091 30.7077 30.7097 30.7077 30.7101 30.7087
800 31.4961 31.4931 31.4952 31.4932 31.4961 31.4941 31.4965 31.4951 31.4971 31.4951 31.4975 31.4961
850 33.4646 33.4607 33.4636 33.4614 33.4646 33.4624 33.4651 33.4635 33.4657 33.4635 33.4662 33.4646
900 35.4331 35.4292 35.4321 35.4299 32L 35.4331 35.4309 22L 35.4336 35.4320 11L 35.4342 35.4320 11L 35.4347 35.4331 0T
29T 39T 44T 50T 55T
950 37.4016 37.3977 37.4006 37.3984 37.4016 37.3994 37.4021 37.4005 37.4027 37.4005 37.4032 37.4016
1000 39.3701 39.3662 39.3691 39.3669 39.3701 39.3679 39.3706 39.3690 39.3712 39.3690 39.3717 39.3701
1060 41.7323 41.7274 41.7312 41.7286 41.7323 41.7297 41.7328 41.7310 41.7336 41.7310 41.7341 41.7323
1120 44.0945 44.0896 44.0934 44.0908 37L 44.0945 44.0919 26L 44.0950 44.0932 13L 44.0958 44.0932 13L 44.0963 44.0945 0T
38T 49T 54T 62T 67T
1180 46.4567 46.4518 46.4556 46.4530 46.4567 46.4541 46.4572 46.4554 46.4580 46.4554 46.4585 46.4567
1250 49.2126 49.2077 49.2115 49.2089 49.2126 49.2100 49.2131 49.2113 49.2139 49.2113 49.2144 49.2126
264
ISO Fits for Solid Steel Shafts
Shaft Bearing-Seat Diameters (Values in Inches)
k6 m5 m6 n6 p6 r6 r7
Brg. Fit Fit Fit Fit Fit Fit Fit
Bore in in in in in in in
Dia. Shaft Dia. 0.0001" Shaft Dia. 0.0001" Shaft Dia. 0.0001" Shaft Dia. 0.0001" Shaft Dia. 0.0001" Shaft Dia. 0.0001" Shaft Dia. 0.0001"
mm
Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min.
4 0.1579 0.1575 0.1579 0.1577 0.1580 0.1577 0.1581 0.1578
5 0.1973 0.1969 0T 0.1973 0.1971 2T 0.1974 0.1971 2T 0.1975 0.1972 3T
6 0.2366 0.2362 7T 0.2366 0.2364 7T 0.2367 0.2364 8T 0.2368 0.2365 9T
7 0.2760 0.2756 0.2761 0.2758 0.2762 0.2758 0.2764 0.2760
8 0.3154 0.3150 0T 0.3155 0.3152 2T 0.3156 0.3152 2T 0.3158 0.3154 4T
9 0.3547 0.3543 7T 0.3548 0.3545 8T 0.3549 0.3545 9T 0.3551 0.3547 11T
10 0.3941 0.3937 0.3942 0.3939 0.3943 0.3939 0.3945 0.3941
12 0.4729 0.4724 0.4730 0.4727 0.4731 0.4727 0.4733 0.4729
15 0.5911 0.5906 0T 0.5912 0.5909 3T 0.5913 0.5909 3T 0.5915 0.5911 5T
17 0.6698 0.6693 8T 0.6699 0.6696 9T 0.6700 0.6696 10T 0.6702 0.6698 12T
20 0.7880 0.7875 0.7881 0.7877 0.7882 0.7877 0.7885 0.7880
25 0.9849 0.9844 1T 0.9850 0.9846 3T 0.9851 0.9846 3T 0.9854 0.9849 6T
30 1.1817 1.1812 10T 1.1818 1.1814 11T 1.1819 1.1814 12T 1.1822 1.1817 15T
35 1.3787 1.3781 1.3788 1.3784 1.3790 1.3784 1.3793 1.3787
40 1.5755 1.5749 1T 1.5756 1.5752 4T 1.5758 1.5752 4T 1.5761 1.5655 7T
45 1.7724 1.7718 12T 1.7725 1.7721 13T 1.7727 1.7721 15T 1.7730 1.7724 18T
50 1.9692 1.9686 1.9693 1.9689 1.9695 1.9689 1.9698 1.9692
55 2.1662 2.1655 2.1663 2.1658 2.1666 2.1658 2.1669 2.1662
60 2.3630 2.3623 2.3631 2.3626 2.3634 2.3626 2.3637 2.3630
65 2.5599 2.5592 1T 2.5600 2.5595 4T 2.5603 2.5595 4T 2.5606 2.5599 8T
70 2.7567 2.7560 14T 2.7568 2.7563 15T 2.7571 2.7563 18T 2.7574 2.7567 21T
75 2.9536 2.9529 2.9537 2.9532 2.9540 2.9532 2.9543 2.9536
80 3.1504 3.1497 3.1505 3.1500 3.1508 3.1500 3.1511 3.1504
85 3.3475 3.3466 3.3476 3.3470 3.3479 3.3470 3.3483 3.3474 3.3488 3.3480
90 3.5443 3.5434 3.5444 3.5438 3.5447 3.5438 3.5451 3.5442 3.5456 3.5448
95 3.7412 3.7403 3.7413 3.7407 3.7416 3.7407 3.7420 3.7411 3.7425 3.7417
100 3.9380 3.9371 1T 3.9381 3.9375 5T 3.9384 3.9375 5T 3.9388 3.9379 9T 3.9393 3.9385 15T
105 4.1349 4.1340 18T 4.1350 4.1344 19T 4.1353 4.1344 22T 4.1357 4.1348 26T 4.1362 4.1354 31T
110 4.3317 4.3308 4.3318 4.3312 4.3321 4.3312 4.3325 4.3316 4.3330 4.3322
115 4.5286 4.5277 4.5287 4.5281 4.5290 4.5281 4.5294 4.5285 4.5299 4.5291
120 4.7254 4.7245 4.7255 4.7249 4.7258 4.7249 4.7262 4.7253 4.7267 4.7259
125 4.9224 4.9214 4.9226 4.9219 4.9229 4.9219 4.9233 4.9224 4.9240 4.9230 4.9248 4.9239
130 5.1192 5.1182 5.1194 5.1187 5.1197 5.1187 5.1201 5.1192 5.1208 5.1198 5.1216 5.1207
140 5.5129 5.5119 5.5131 5.5124 5.5134 5.5124 5.5138 5.5129 5.5145 5.5135 5.5153 5.5144
150 5.9066 5.9056 1T 5.9068 5.9061 6T 5.9071 5.9061 6T 5.9075 5.9066 11T 5.9082 5.9072 17T 5.9090 5.9081 26T
160 6.3003 6.2993 21T 6.3005 6.2998 23T 6.3008 6.2998 26T 6.3012 6.3003 30T 6.3019 6.3009 37T 6.3027 6.3018 45T
170 6.6940 6.6930 6.6942 6.6935 6.6945 6.6935 6.6949 6.6940 6.6956 6.6946 6.6964 6.6955
180 7.0877 7.0867 7.0879 7.0872 7.0882 7.0872 7.0886 7.0877 7.0893 7.0883 7.0901 7.0892
190 7.4816 7.4805 7.4818 7.4810 7.4821 7.4810 7.4827 7.4815 7.4834 7.4823 7.4845 7.4833 30T
200 7.8753 7.8742 2T 7.8755 7.8747 7T 7.8758 7.8747 7T 7.8764 7.8752 12T 7.8771 7.8760 20T 7.8782 7.8770 54T
220 8.6627 8.6616 25T 8.6629 8.6621 27T 8.6632 8.6621 30T 8.6638 8.6626 36T 8.6645 8.6634 43T 8.6657 8.6645 31T/55T 8.6664 8.6645 31T/62T
240 9.4501 9.4490 9.4503 9.4495 9.4506 9.4495 9.4512 9.4500 9.4519 9.4508 9.4532 9.4521 33T 9.4539 9.4521 33T
250 9.8438 9.8427 9.8440 9.8432 9.8443 9.8432 9.8449 9.8437 9.8456 9.8445 9.8469 9.8458 56T 9.8476 9.8458 63T
260 10.2376 10.2364 10.2379 10.2370 10.2382 10.2370 10.2388 10.2375 10.2397 10.2384 10.2412 10.2399 37T 10.2419 10.2399 37T
280 11.0250 11.0238 2T 11.0253 11.0244 8T 11.0256 11.0244 8T 11.0262 11.0249 13T 11.0271 11.0258 22T 11.0286 11.0273 64T 11.0293 11.0273 71T
300 11.8124 11.8112 28T 11.8127 11.8118 31T 11.8130 11.8118 34T 11.8136 11.8123 40T 11.8145 11.8132 49T 11.8161 11.8149 39T 11.8169 11.8149 39T
310 12.2061 12.2049 12.2064 12.2055 12.2067 12.2055 12.2073 12.2060 12.2082 12.2069 12.2098 12.2086 65T 12.2106 12.2086 73T
320 12.5997 12.5986 12.6002 12.5992 12.6006 12.5992 12.6013 12.5999 12.6023 12.6008 12.6041 12.6027 43T 12.6049 12.6027 43T
340 13.3873 13.3860 13.3876 13.3866 13.3880 13.3866 13.3887 13.3873 13.3897 13.3882 13.3915 13.3901 73T 13.3923 13.3901 81T
350 13.7810 13.7797 2T 13.7813 13.7803 8T 13.7817 13.7803 8T 13.7824 13.7810 15T 13.7834 13.7819 24T 13.7852 13.7838 13.7860 13.7838
360 14.1747 14.1734 31T 14.1750 14.1740 34T 14.1754 14.1740 38T 14.1761 14.1747 45T 14.1771 14.1756 55T 14.1791 14.1777 45T 14.1799 14.1777 45T
380 14.9621 14.9608 14.9624 14.9614 14.9628 14.9614 14.9635 14.9621 14.9645 14.9630 14.9665 14.9651 75T 14.9673 14.9651 83T
400 15.7495 15.7482 15.7498 15.7488 15.7502 15.7488 15.7509 15.7495 15.7519 15.7504 15.7539 15.7525 15.7547 15.7525
420 16.5371 16.5356 16.5374 16.5363 16.5379 16.5363 16.5385 16.5370 16.5397 16.5381 16.5419 16.5404 50T 16.5428 16.5404 50T
440 17.3245 17.3230 2T 17.3248 17.3237 9T 17.3253 17.3237 9T 17.3259 17.3244 16T 17.3271 17.3255 27T 17.3293 17.3278 83T 17.3302 17.3278 92T
460 18.1119 18.1104 35T 18.1122 18.1111 38T 18.1127 18.1111 43T 18.1133 18.1118 49T 18.1145 18.1129 61T 18.1170 18.1154 52T 18.1179 18.1154 52T
480 18.8993 18.8978 18.8996 18.8985 18.9001 18.8985 18.9007 18.8992 18.9019 18.9003 18.9044 18.9028 86T 18.9053 18.9028 95T
500 19.6867 19.6852 19.6870 19.6859 19.6875 19.6859 19.6881 19.6866 19.6893 19.6877 19.6918 19.6902 19.6927 19.6902
530 20.8678 20.8661 20.8683 20.8671 20.8695 20.8678 20.8709 20.8692 20.8737 20.8720 59T 20.8748 20.8720 59T
560 22.0489 22.0472 0T 22.0494 22.0482 10T 22.0506 22.0489 17T 22.0520 22.0503 31T 22.0548 23.0531 96T 22.0559 22.0531 107T
600 23.6237 23.6220 37T 23.6242 23.6230 42T 23.6254 23.6237 54T 23.6268 23.6251 68T 23.6298 23.6281 61T 23.6309 23.6281 61T
630 24.8048 24.8031 24.8053 24.8041 24.8065 24.8048 24.8079 24.8062 24.8109 24.8092 98T 24.8120 24.8092 109T
660 25.9862 25.9843 25.9869 25.9855 25.9682 25.9663 25.9897 25.9878 25.9932 25.9912 69T 25.9943 25.9912 69T
670 26.3799 26.3780 26.3806 26.3792 26.3819 26.3800 26.3834 26.3815 26.3869 28.3849 119T 26.3880 26.3849 130T
710 27.9547 27.9528 0T 27.9554 27.9540 12T 27.9567 27.9548 20T 27.9582 27.9563 35T 27.9617 27.9597 27.9628 27.9597
750 29.5295 29.5276 49T 29.5302 29.5288 56T 29.5315 29.5296 69T 29.5330 29.5311 84T 29.5369 29.5349 73T 29.5380 29.5349 73T
780 30.7106 30.7087 30.7113 30.7099 30.7126 30.7107 30.7141 30.7122 30.7180 30.7160 123T 30.7191 30.7160 134T
800 31.4980 31.4961 31.4987 31.4973 31.5000 31.4981 31.5015 31.4996 31.5054 31.5034 31.5065 31.5034
850 33.4668 33.4646 33.4675 33.4659 33.4690 33.4668 33.4707 33.4685 33.4751 33.4729 83T 33.4764 33.4729 83T
900 35.4353 35.4331 0T 35.4360 35.4344 13T 35.4375 35.4353 22T 35.4392 35.4370 39T 35.4436 35.4414 144T 35.4449 35.4414 157T
950 37.4038 37.4016 61T 37.4045 37.4029 68T 37.4060 37.4038 83T 37.4077 37.4055 100T 37.4125 37.4103 87T 37.4138 37.4103 87T
1000 39.3723 39.3701 39.3730 39.3714 39.3745 39.3723 39.3762 39.3740 39.3810 37.3788 148T 39.3823 39.3788 161T
1060 41.7349 41.7323 41.7357 41.7339 41.7375 41.7349 41.7396 41.7370 41.7447 41.7421 98T 41.7463 41.7421 98T
1120 44.0971 44.0945 0T 44.0979 44.0961 16T 44.0997 44.0971 26T 44.1018 44.0992 47T 44.1069 44.1043 173T 44.1085 44.1043 189T
1180 46.4593 46.4567 75T 46.4601 46.4583 83T 46.4619 46.4593 101T 46.4640 46.4614 122T 46.4695 46.4669 102T 46.4711 46.4669 102T
1250 49.2152 49.2126 49.2160 49.2142 49.2178 49.2152 49.2199 49.2173 49.2254 49.2228 177T 49.2270 49.2228 193T
265
ISO Fits For Cast Iron And Steel Housings MRC Bearing Services
The ISO Housing Tolerances listed are shown in the tables on pages 267 to 269.
Radial Bearings
Conditions Examples Tolerance Displacement of Outer Ring
Inner Ring Rotation
Loads of all kinds General bearing applications, railway axleboxes H61) Can be displaced
Light and normal loads (P ≤ 0.12C) with simple General bearing applications H8 Can be displaced
working conditions
Heat conduction through shaft Drying cylinders, large electrical machines with G7 2) Can be displaced
spherical roller bearings
Normal and heavy loads (P > 0.06C). Axial Electrical motors, pumps, crankshaft bearings K7 Cannot usually be displaced
displacement of outer ring unnecessary
Heavy loads on bearings in thin-walled housings, Roller bearing wheel hubs, big end bearings P7 Cannot be displaced
heavy shock loads
Normal and heavy loads (P > 0.06C) Ball bearing wheel hubs, big end bearings, crane N7 Cannot be displaced
travelling wheels
Light and variable loads (P ≤ 0.06C) Conveyor rollers, rope sheaves, belt tension pulleys M7 Cannot be displaced
*Variable external loads, shock loads, and vibratory and unbalanced loads in high-speed machinery cannot be accurately described and are classified as “direction of load indeterminate.’”
**Warning: If a press fit is also being used on the shaft, special consideration should be given to assembly and bearing internal clearance.
1) For large bearings (D > 250 mm) and temperature difference between outer ring and housing >10˚C, use G7.
2) For large bearings (D > 250 mm) and temperature difference between outer ring and housing >10˚C, use F7.
266
ISO Fits for Cast Iron and Steel Housings
Housing Bearing-Seat Diameters (Values in Inches)
Bearing Outside
Diameter F7 G7 H8 H7 H6
Inches Housing Bore Fit Housing Bore Fit Housing Bore Fit Housing Bore Fit Housing Bore Fit
mm in in in in in
Max Min. Min. Max. 0.0001" Min. Max. 0.0001" Min. Max. 0.0001" Min. Max. 0.0001" Min. Max. 0.0001"
16 0.6299 0.6296 0.6305 0.6312 16L 0.6301 0.6308 12L 0.6299 0.6310 14L 0.6299 0.6306 10L 0.6299 0.6303 7L
6L 2L 0 0 0
19 0.7480 0.7476 0.7488 0.7496 0.7483 0.7491 0.7480 0.7493 0.7480 0.7488 0.7480 0.7485
21 0.8268 0.8264 0.8276 0.8284 0.8271 0.8279 0.8268 0.8281 0.8268 0.8276 0.8268 0.8273
22 0.8661 0.8657 0.8669 0.8677 0.8664 0.8672 0.8661 0.8674 0.8661 0.8669 0.8661 0.8666
24 0.9449 0.9445 0.9457 0.9465 20L 0.9452 0.9460 15L 0.9449 0.9462 17L 0.9449 0.9457 12L 0.9449 0.9454 9L
26 1.0236 1.0232 1.0244 1.0252 8L 1.0239 1.0247 3L 1.0236 1.0249 0 1.0236 1.0244 0 1.0236 1.0241 0
28 1.1024 1.1020 1.1032 1.1040 1.1027 1.1035 1.1024 1.1037 1.1024 1.1032 1.1024 1.1029
30 1.1811 1.1807 1.1819 1.1827 1.1814 1.1822 1.1811 1.1824 1.1811 1.1819 1.1811 1.1816
32 1.2598 1.2594 1.2608 1.2618 1.2602 1.2611 1.2598 1.2613 1.2598 1.2608 1.2598 1.2604
35 1.3780 1.3776 1.3790 1.4000 1.3784 1.3793 1.3780 1.3795 1.3780 1.3790 1.3780 1.3786
37 1.4567 1.4563 1.4577 1.4587 24L 1.4571 1.4580 17L 1.4567 1.4582 19L 1.4567 1.4577 14L 1.4567 1.4573 10L
40 1.5748 1.5744 1.5758 1.5768 10L 1.5752 1.5761 4L 1.5748 1.5763 0 1.5748 1.5758 0 1.5748 1.5754 0
42 1.6535 1.6531 1.6545 1.6555 1.6539 1.6548 1.6535 1.6550 1.6535 1.6545 1.6535 1.6541
47 1.8504 1.8500 1.8514 1.8524 1.8508 1.8517 1.8504 1.8519 1.8504 1.8514 1.8504 1.8510
52 2.0472 2.0467 2.0484 2.0496 2.0476 2.0488 2.0472 2.0490 2.0472 2.0484 2.0472 2.0479
55 2.1654 2.1649 2.1666 2.1678 2.1658 2.1670 2.1654 2.1672 2.1654 2.1666 2.1654 2.1661
58 2.2835 2.2830 2.2847 2.2859 2.2839 2.2851 2.2835 2.2853 2.2835 2.2847 2.2835 2.2842
62 2.4409 2.4404 2.4421 2.4433 29L 2.4413 2.4425 21L 2.4409 2.4427 23L 2.4409 2.4421 17L 2.4409 2.4416 12L
65 2.5591 2.5586 2.5603 2.5615 12L 2.5595 2.5607 4L 2.5591 2.5609 0 2.5591 2.5603 0 2.5591 2.5598 0
70 2.7559 2.7554 2.7571 2.7583 2.7563 2.7575 2.7559 2.7577 2.7559 2.7571 2.7559 2.7566
72 2.8346 2.8341 2.8358 2.8370 2.8350 2.8362 2.8346 2.8364 2.8346 2.8358 2.8346 2.8353
78 3.0709 3.0704 3.0721 3.0733 3.0713 3.0725 3.0709 3.0727 3.0709 3.0721 3.0709 3.0716
80 3.1496 3.1491 3.1508 3.1520 3.1500 3.1512 3.1496 3.1514 3.1496 3.1508 3.1496 3.1503
85 3.3465 3.3459 3.3479 3.3493 3.3470 3.3484 3.3465 3.3486 3.3465 3.3479 3.3465 3.3474
90 3.5433 3.5427 3.5447 3.5461 3.5438 3.5452 3.5433 3.5454 3.5433 3.5447 3.5433 3.5442
100 3.9370 3.9364 3.9384 3.9398 34L 3.9375 3.9389 25L 3.9370 3.9391 27L 3.9370 3.9384 20L 3.9370 3.9379 15L
110 4.3307 4.3301 4.3321 4.3335 14L 4.3312 4.3326 5L 4.3307 4.3328 0 4.3307 4.3321 0 4.3307 4.3316 0
115 4.5276 4.5270 4.5290 4.5304 4.5281 4.5295 4.5276 4.5297 4.5276 4.5290 4.5276 4.5285
120 4.7244 4.7238 4.7258 4.7272 4.7249 4.7263 4.7244 4.7265 4.7244 4.7258 4.7244 4.7253
125 4.9213 4.9206 4.9230 4.9246 4.9219 4.9234 4.9213 4.9238 4.9213 4.9229 4.9213 4.9223
130 5.1181 5.1174 5.1198 5.1214 5.1187 5.1202 5.1181 5.1206 5.1181 5.1197 5.1181 5.1191
135 5.3150 5.3143 5.3167 5.3183 40L 5.3156 5.3171 28L 5.3150 5.3175 32L 5.3150 5.3166 23L 5.3150 5.3160 17L
140 5.5118 5.5111 5.5135 5.5151 17L 5.5124 5.5139 6L 5.5118 5.5143 0 5.5118 5.5134 0 5.5118 5.5128 0
145 5.7087 5.7080 5.7104 5.7120 5.7093 5.7108 5.7087 5.7112 5.7087 5.7103 5.7087 5.7097
150 5.9055 5.9048 5.9072 5.9088 5.9061 5.9076 5.9055 5.9080 5.9055 5.9071 5.9055 5.9065
160 6.2992 6.2982 6.3009 6.3025 6.2998 6.3013 6.2992 6.3017 6.2992 6.3008 6.2992 6.3002
170 6.6929 6.6919 6.6946 6.6962 43L 6.6935 6.6950 31L 6.6929 6.6954 35L 6.6929 6.6945 26L 6.6929 6.6939 20L
180 7.0866 7.0856 7.0883 7.0899 17L 7.0872 7.0887 6L 7.0866 7.0891 0 7.0866 7.0882 0 7.0866 7.0876 0
190 7.4803 7.4791 7.4823 7.4841 7.4809 7.4827 7.4803 7.4831 7.4803 7.4821 7.4803 7.4814
200 7.8740 7.8728 7.8760 7.8778 7.8746 7.8764 7.8740 7.8768 7.8740 7.8758 7.8740 7.8751
210 8.2677 8.2665 8.2697 8.2715 8.2683 8.2701 8.2677 8.2705 8.2677 8.2695 8.2677 8.2688
215 8.4646 8.4634 8.4666 8.4684 50L 8.4652 8.4670 36L 8.4646 8.4674 40L 8.4646 8.4664 30L 8.4646 8.4657 23L
225 8.8583 8.8571 8.8603 8.8621 20L 8.8589 8.8607 6L 8.8583 8.8611 0 8.8583 8.8601 0 8.8583 8.8594 0
240 9.4488 9.4476 9.4508 9.4526 9.4494 9.4512 9.4488 9.4516 9.4488 9.4506 9.4488 9.4499
250 9.8425 9.8413 9.8445 9.8463 9.8431 9.8449 9.8425 9.8453 9.8425 9.8443 9.8425 9.8436
260 10.2362 10.2348 10.2384 10.2405 10.2369 10.2389 10.2362 10.2394 10.2362 10.2382 10.2362 10.2375
270 10.6299 10.6285 10.6321 10.6342 10.6306 10.6326 10.6299 10.6331 10.6299 10.6319 10.6299 10.6312
280 11.0236 11.0222 11.0258 11.0279 57L 11.0243 11.0263 41L 11.0236 11.0268 46L 11.0236 11.0256 34L 11.0236 11.0249 27L
300 11.8110 11.8096 11.8132 11.8153 22L 11.8117 11.8137 7L 11.8110 11.8142 0 11.8110 11.8130 0 11.8110 11.8123 0
310 12.2047 12.2033 12.2069 12.2090 12.2054 12.2074 12.2047 12.2079 12.2047 12.2067 12.2047 12.2060
320 12.5984 12.5968 12.6008 12.6031 12.5991 12.6014 12.5984 12.6019 12.5984 12.6006 12.5984 12.5998
340 13.3858 13.3842 13.3882 13.3905 13.3865 13.3888 13.3858 13.3893 13.3858 13.3880 13.3858 13.3872
350 13.7795 13.7779 13.7819 13.7842 63L 13.7802 13.7825 46L 13.7795 13.7830 51L 13.7795 13.7817 38L 13.7795 13.7809 30L
360 14.1732 14.1716 14.1756 14.1779 24L 14.1739 14.1762 7L 14.1732 14.1767 0 14.1732 14.1754 0 14.1732 14.1746 0
380 14.9606 14.9590 14.9630 14.9653 14.9613 14.9636 14.9606 14.9641 14.9606 14.9628 14.9606 14.9620
400 15.7480 15.7464 15.7504 15.7527 15.7487 15.7510 15.7480 15.7515 15.7480 15.7502 15.7480 15.7494
420 16.5354 16.5336 16.5381 16.5406 16.5362 16.5387 16.5354 16.5392 16.5354 16.5379 16.5354 16.5370
440 17.3228 17.3210 17.3255 17.3280 70L 17.3236 17.3261 51L 17.3228 17.3266 56L 17.3228 17.3253 43L 17.3228 17.3244 34L
460 18.1102 18.1084 18.1129 18.1154 27L 18.1110 18.1135 8L 18.1102 18.1140 0 18.1102 18.1127 0 18.1102 18.1118 0
480 18.8976 18.8958 18.9003 18.9028 18.8984 18.9009 18.8976 18.9014 18.8976 18.9001 18.8976 18.8992
500 19.6850 19.6832 19.6877 19.6902 19.6858 19.6883 19.6850 19.6888 19.6850 19.6875 19.6850 19.6866
520 20.4724 20.4704 20.4754 20.4781 20.4733 20.4760 20.4724 20.4767 20.4724 20.4752 20.4724 20.4741
540 21.2598 21.2578 21.2628 21.2655 21.2607 21.2634 21.2598 21.2641 21.2598 21.2626 21.2598 21.2615
560 22.0472 22.0452 22.0502 22.0529 77L 22.0481 22.0508 56L 22.0472 22.0515 63L 22.0472 22.0500 48L 22.0472 22.0489 37L
580 22.8346 22.8326 22.8376 22.8403 30L 22.8355 22.8382 9L 22.8346 22.8389 0 22.8346 22.8374 0 22.8346 22.8363 0
600 23.6220 23.6200 23.6250 23.6277 23.6229 23.6256 23.6220 23.6263 23.6220 23.6248 23.6220 23.6237
620 24.4094 24.4074 24.4124 24.4151 24.4103 24.4130 24.4094 24.4137 24.4094 24.4122 24.4094 24.4111
650 25.5906 25.5876 25.5937 25.5969 25.5915 25.5947 25.5906 25.5955 25.5906 25.5937 25.5906 25.5926
670 26.3780 26.3750 26.3811 26.3843 26.3789 26.3821 26.3780 26.3829 26.3780 26.3811 26.3780 26.3800
680 26.7717 26.7687 26.7748 26.7780 26.7726 26.7758 26.7717 26.7766 26.7717 26.7748 26.7717 26.7737
700 27.5591 27.5561 27.5622 27.5654 93L 27.5600 27.5632 71L 27.5591 27.5640 79L 27.5591 27.5622 61L 27.5591 27.5611 50L
720 28.3465 28.3435 28.3496 28.3528 31L 28.3474 28.3506 9L 28.3465 28.3514 0 28.3465 28.3496 0 28.3465 28.3485 0
750 29.5276 29.5246 29.5307 29.5339 29.5285 29.5317 29.5276 29.5325 29.5276 29.5307 29.5276 29.5296
780 30.7087 30.7057 30.7118 30.7150 30.7096 30.7128 30.7087 30.7136 30.7087 30.7118 30.7087 30.7107
790 31.1024 31.0994 31.1055 31.1087 31.1033 31.1065 31.1024 31.1073 31.1024 31.1055 31.1024 31.1044
820 32.2835 32.2796 32.2869 32.2904 32.2845 32.2881 32.2835 32.2890 32.2835 32.2870 32.2835 32.2857
850 33.4646 33.4607 33.4680 33.4715 33.4656 33.4692 33.4646 33.4701 33.4646 33.4681 33.4646 33.4668
870 34.2520 34.2481 34.2554 34.2589 34.2530 34.2566 34.2520 34.2575 34.2520 34.2555 34.2520 34.2542
920 36.2205 36.2166 36.2239 36.2274 108L 36.2215 36.2251 85L 36.2205 36.2260 94L 36.2205 36.2240 74L 36.2205 36.2227 61L
950 37.4016 37.3977 37.4050 37.4085 34L 37.4026 37.4062 10L 37.4016 37.4071 0 37.4016 37.4051 0 37.4016 37.4038 0
980 38.5827 38.5788 38.5861 38.5896 38.5837 38.5873 38.5827 38.5882 38.5827 38.5862 38.5827 38.5849
1000 39.3701 39.3662 39.3735 39.3770 39.3711 39.3747 39.3701 39.3756 39.3701 39.3736 39.3701 39.3723
1150 45.2756 45.2707 45.2795 45.2836 129L 45.2767 45.2808 101L 45.2756 45.2821 114L 45.2756 45.2797 90L 45.2756 45.2782 75L
1250 49.2126 49.2077 49.2165 49.2206 39L 49.2137 49.2178 11L 49.2126 49.2191 0 49.2126 49.2167 0 49.2126 49.2152 0
1400 55.1181 55.1118 55.1224 55.1274 156L 55.1193 55.1242 124L 55.1181 55.1258 140L 55.1181 55.1230 112L 55.1181 55.1212 94L
1600 62.9921 62.9858 62.9964 63.0014 43L 62.9933 62.9982 12L 62.9921 62.9998 0 62.9921 62.9970 0 62.9921 62.9952 0
1800 70.8661 70.8582 70.8708 70.8767 185L 70.8674 70.8733 151L 70.8661 70.8752 170L 70.8661 70.8720 138L 70.8661 70.8697 115L
2000 78.7402 78.7323 78.7449 78.7508 47L 78.7415 78.7474 13L 78.7402 78.7493 0 78.7402 78.7461 0 78.7402 78.7438 0
2300 90.5512 90.5414 90.5563 90.5632 218L 90.5525 90.5594 180L 90.5512 90.5622 208L 90.5512 90.5581 167L 90.5512 90.5555 141L
2500 98.4252 98.4154 98.4303 98.4372 51L 98.4265 98.4334 13L 98.4252 98.4362 0 98.4252 98.4321 0 98.4252 98.4295 0
Note: T indicates tight fit. L indicates loose fit.
267
ISO Fits for Cast Iron and Steel Housings MRC Bearing Services
Housing Bearing-Seat Diameters (Values in Inches)
Bearing Outside
Diameter J6 J7 K6 K7 M6
Inches Housing Bore Fit Housing Bore Fit Housing Bore Fit Housing Bore Fit Housing Bore Fit
mm in in in in in
Max Min. Min. Max. 0.0001" Min. Max. 0.0001" Min. Max. 0.0001" Min. Max. 0.0001" Min. Max. 0.0001"
16 0.6299 0.6296 0.6297 0.6301 5L 0.6296 0.6303 7L 0.6295 0.6300 4L 0.6294 0.6301 5L 0.6293 0.6297 1L
2T 3T 4T 5T 6T
19 0.7480 0.7476 0.7478 0.7483 0.7476 0.7485 0.7476 0.7481 0.7474 0.7482 0.7473 0.7478
21 0.8268 08264 0.8266 0.8271 0.8264 0.8273 0.8264 0.8269 0.8262 0.8270 0.8261 0.8266
22 0.8661 0.8657 0.8659 0.8664 0.8657 0.8666 0.8657 0.8662 0.8655 0.8663 0.8654 0.8659
24 0.9449 0.9445 0.9447 0.9452 7L 0.9445 0.9454 9L 0.9445 0.9450 5L 0.9443 0.9451 6L 0.9442 0.9447 2L
26 1.0236 1.0232 1.0234 1.0239 2T 1.0232 1.0241 4T 1.0232 1.0237 4T 1.0230 1.0238 6T 1.0229 1.0234 7T
28 1.1024 1.1020 1.1022 1.1027 1.1020 1.1029 1.1020 1.1025 1.1018 1.1026 1.1017 1.1022
30 1.1811 1.1807 1.1809 1.1814 1.1807 1.1816 1.1807 1.1812 1.1805 1.1813 1.1804 1.1809
32 1.2598 1.2594 1.2596 1.2602 1.2594 1.2604 1.2593 1.2599 1.2591 1.2601 1.2590 1.2596
35 1.3780 1.3776 1.3778 1.3784 1.3776 1.3786 1.3775 1.3781 1.3773 1.3783 1.3772 1.3778
37 1.4567 1.4563 1.4565 1.4571 8L 1.4563 1.4573 10L 1.4562 1.4568 5L 1.4560 1.4570 7L 1.4559 1.4565 2L
40 1.5748 1.5744 1.5746 1.5752 2T 1.5744 1.5754 4T 1.5743 1.5749 5T 1.5741 1.5751 7T 1.5740 1.5746 8T
42 1.6535 1.6531 1.6533 1.6539 1.6531 1.6541 1.6530 1.6536 1.6528 1.6538 1.6527 1.6533
47 1.8504 1.8500 1.8502 1.8508 1.8500 1.8510 1.8499 1.8505 1.8497 1.8507 1.8496 1.8502
52 2.0472 2.0467 2.0470 2.0477 2.0467 2.0479 2.0466 2.0474 2.0464 2.0476 2.0463 2.0470
55 2.1654 2.1649 2.1652 2.1659 2.1649 2.1661 2.1648 2.1656 2.1646 2.1658 2.1645 2.1652
58 2.2835 2.2830 2.2833 2.2840 2.2830 2.2842 2.2829 2.2837 2.2827 2.2839 2.2826 2.2833
62 2.4409 2.4404 2.4407 2.4414 2.4404 2.4416 2.4403 2.4411 2.4401 2.4413 2.4400 2.4407
65 2.5591 2.5586 2.2589 2.2596 10L 2.5586 2.5598 12L 2.5585 2.5593 7L 2.5583 2.5595 9L 2.5582 2.5589 3L
70 2.7559 2.7554 2.7557 2.7564 2T 2.7554 2.7566 5T 2.7553 2.7561 6T 2.7551 2.7563 8T 2.7550 2.7557 9T
72 2.8346 2.8341 2.8344 2.8351 2.8341 2.8353 2.8340 2.8348 2.8338 2.8350 2.8337 2.8344
78 3.0709 3.0704 3.0707 3.0714 3.0704 3.0716 3.0703 3.0711 3.0701 3.0713 3.0700 3.0707
80 3.1496 3.1491 3.1494 3.1501 3.1491 3.1503 3.1490 3.1498 3.1488 3.1500 3.1487 3.1494
85 3.3465 3.3459 3.3463 3.3471 3.3460 3.3474 3.3458 3.3467 3.3455 3.3469 3.3454 3.3463
90 3.5433 3.5427 3.5431 3.5439 3.5428 3.5442 3.5426 3.5435 3.5423 3.5437 3.5422 3.5431
100 3.9370 3.9364 3.9368 3.9376 12L 3.9365 3.9379 15L 3.9363 3.9372 8L 3.9360 3.9374 10L 3.9359 3.9368 4L
110 4.3307 4.3301 4.3305 4.3313 2T 4.3302 4.3316 5T 4.3300 4.3309 7T 4.3297 4.3311 10T 4.3296 4.3305 11T
115 4.5276 4.5270 4.5274 4.5282 4.5271 4.5285 4.5269 4.5278 4.5266 4.5280 4.5265 4.5274
120 4.7244 4.7238 4.7242 4.7250 4.7239 4.7253 4.7237 4.7246 4.7234 4.7248 4.7233 4.7242
125 4.9213 4.9206 4.9210 4.9220 4.9207 4.9223 4.9205 4.9215 4.9202 4.9218 4.9200 4.9210
130 5.1181 5.1174 5.1178 5.1188 5.1175 5.1191 5.1173 5.1183 5.1170 5.1186 5.1168 5.1178
135 5.3150 5.3143 5.3147 5.3157 5.3144 5.3160 5.3142 5.3152 5.3139 5.3155 5.3137 5.3147
140 5.5118 5.5111 5.5115 5.5125 14L 5.5112 5.5128 17L 5.5110 5.5120 9L 5.5107 5.5123 12L 5.5105 5.5115 4L
145 5.7087 5.7080 5.7084 5.7094 3T 5.7081 5.7097 6T 5.7079 5.7089 8T 5.7076 5.7092 11T 5.7074 5.7084 13T
150 5.9055 5.9048 5.9052 5.9062 5.9049 5.9065 5.9047 5.9057 5.9044 5.9060 5.9042 5.9052
160 6.2992 6.2982 6.2989 6.2999 6.2986 6.3002 6.2984 6.2994 6.2981 6.2997 6.2979 6.2989
170 6.6929 6.6919 6.6926 6.6936 17L 6.6923 6.6939 20L 6.6921 6.6931 12L 6.6918 6.6934 15L 6.6916 6.6926 7L
180 7.0866 7.0856 7.0863 7.0873 3T 7.0860 7.0876 6T 7.0858 7.0868 8T 7.0855 7.0871 11T 7.0853 7.0863 13T
190 7.4803 7.4791 7.4800 7.4812 7.4797 7.4815 7.4794 7.4805 7.4790 7.4808 7.4788 7.4800
200 7.8740 7.8728 7.8737 7.8749 7.8734 7.8752 7.8731 7.8742 7.8727 7.8745 7.8725 7.8737
210 8.2677 8.2665 8.2674 8.2686 8.2671 8.2689 8.2668 8.2679 8.2664 8.2682 8.2662 8.2674
215 8.4646 8.4634 8.4643 8.4655 21L 8.4640 8.4658 24L 8.4637 8.4648 14L 8.4633 8.4651 17L 8.4631 8.4643 9L
225 8.8583 8.8571 8.8580 8.8592 3T 8.8577 8.8595 6T 8.8574 8.8585 9T 8.8570 8.8588 13T 8.8568 8.8580 15T
240 9.4488 9.4476 9.4485 9.4497 9.4482 9.4500 9.4479 9.4490 9.4475 9.4493 9.4473 9.4485
250 9.8425 9.8413 9.8422 9.8434 9.8419 9.8437 9.8416 9.8427 9.8412 9.8430 9.8410 9.8422
260 10.2362 10.2348 10.2359 10.2372 10.2356 10.2376 10.2351 10.2364 10.2348 10.2368 10.2346 10.2358
270 10.6299 10.6285 10.6296 10.6309 10.6293 10.6313 10.6288 10.6301 10.6285 10.6305 10.6283 10.6295
280 11.0236 11.0222 11.0233 11.0246 24L 11.0230 11.0250 28L 11.0225 11.0238 16L 11.0222 11.0242 20L 11.0220 11.0232 10L
300 11.8110 11.8096 11.8107 11.8120 3T 11.8104 11.8124 6T 11.8099 11.8112 11T 11.8096 11.8116 14T 11.8094 11.8106 16T
310 12.2047 12.2033 12.2044 12.2057 12.2041 12.2061 12.2036 12.2049 12.2033 12.2053 12.2031 12.2043
320 12.5984 12.5968 12.5981 12.5995 12.5977 12.5999 12.5973 12.5987 12.5968 12.5991 12.5966 12.5980
340 13.3858 13.3842 13.3855 13.3869 13.3851 13.3873 13.3847 13.3861 13.3842 13.3865 13.3840 13.3854
350 13.7795 13.7779 13.7792 13.7806 13.7788 13.7810 13.7784 13.7798 13.7779 13.7802 13.7777 13.7791
360 14.1732 14.1716 14.1729 14.1743 27L 14.1725 14.1747 31L 14.1721 14.1735 19L 14.1716 14.1739 23L 14.1714 14.1728 12L
380 14.9606 14.9590 14.9603 14.9617 3T 14.9599 14.9621 7T 14.9595 14.9609 11T 14.9590 14.9613 16T 14.9588 14.9602 18T
400 15.7480 15.7464 15.7477 15.7491 15.7473 15.7495 15.7469 15.7483 15.7464 15.7487 15.7462 15.7476
420 16.5354 16.5336 16.5351 16.5367 16.5346 16.5371 16.5341 16.5357 16.5336 16.5361 16.5334 16.5350
440 17.3228 17.3210 17.3225 17.3241 31L 17.3220 17.3245 35L 17.3215 17.3231 21L 17.3210 17.3235 25L 17.3208 17.3224 14L
460 18.1102 18.1084 18.1099 18.1115 3T 18.1094 18.1119 8T 18.1089 18.1105 13T 18.1084 18.1109 18T 18.1082 18.1098 20T
480 18.8976 18.8958 18.8973 18.8989 18.8968 18.8993 18.8963 18.8979 18.8958 18.8983 18.8956 18.8972
500 19.6850 19.6832 19.6847 19.6863 19.6842 19.6867 19.6837 19.6853 19.6832 19.6857 19.6830 19.6846
520 20.4724 20.4704 20.4721 20.4739 20.4715 20.4743 20.4707 20.4724 20.4696 20.4724 20.4696 20.4714
540 21.2598 21.2578 21.2595 21.2613 21.2589 21.2617 21.2581 21.2598 21.2570 21.2598 21.2570 21.2588
560 22.0472 22.0452 22.0469 22.0487 22.0463 22.0491 22.0455 22.0472 22.0444 22.0472 22.0444 22.0462
580 22.8346 22.8326 22.8343 22.8361 35L 22.8337 22.8365 39L 22.8329 22.8346 20L 22.8318 22.8346 20L 22.8318 22.8336 10L
600 23.6220 23.6200 23.6217 23.6235 3T 23.6211 23.6239 9T 23.6203 23.6220 17T 23.6192 23.6220 28T 23.6192 23.6210 28T
620 24.4094 24.4074 24.4091 24.4109 24.4085 24.4113 24.4077 24.4094 24.4066 24.4094 24.4066 24.4084
650 25.5906 25.5876 25.5902 25.5922 25.5897 25.5928 25.5886 25.5906 25.5875 25.5906 25.5875 25.5894
670 26.3780 26.3750 26.3776 26.3796 26.3771 26.3802 26.3760 26.3780 26.3749 26.3780 26.3749 26.3768
680 26.7717 26.7687 26.7713 26.7733 26.7708 26.7739 26.7697 26.7717 26.7686 26.7717 26.7686 26.7705
700 27.5591 27.5561 27.5587 27.5607 46L 27.5582 27.5613 52L 27.5571 27.5590 30L 27.5560 27.5590 30L 27.5560 27.5579 18L
720 28.3465 28.3435 28.3461 28.3481 4T 28.3456 28.3487 9T 28.3445 28.3465 20T 28.3434 28.3465 31T 28.3434 28.3453 31T
750 29.5276 29.5246 29.5272 29.5292 29.5267 29.5298 29.5256 29.5276 29.5245 29.5276 29.5245 29.5264
780 30.7087 30.7057 30.7083 30.7103 30.7078 30.7109 30.7067 30.7087 30.7056 30.7087 30.7056 30.7075
790 31.1024 31.0994 31.1020 31.1040 31.1015 31.1046 31.1004 31.1024 31.0993 31.1024 31.0993 31.1012
820 32.2835 32.2796 32.2831 32.2853 32.2825 32.2860 32.2813 32.2835 32.2800 32.2835 32.2800 32.2822
850 33.4646 33.4607 33.4642 33.4664 33.4636 33.4671 33.4624 33.4646 33.4611 33.4646 33.4611 33.4633
870 34.2520 34.2481 34.2516 34.2538 34.2510 34.2545 34.2498 34.2520 34.2485 34.2520 34.2485 34.2507
920 36.2205 36.2166 36.2201 36.2223 57L 36.2195 36.2230 64L 36.2183 36.2205 39L 36.2170 36.2205 39L 36.2170 36.2192 26L
950 37.4016 37.3977 37.4012 37.4034 4T 37.4006 37.4041 10T 37.3994 37.4016 22T 37.3981 37.4016 35T 37.3981 37.4003 35T
980 38.5827 38.5788 38.5823 38.5845 38.5817 38.5852 38.5805 38.5827 38.5792 38.5827 38.5792 38.5814
1000 39.3701 39.3662 39.3697 39.3719 39.3691 39.3726 39.3679 39.3701 39.3666 39.3701 39.3666 39.3688
1150 45.2756 45.2707 45.2752 45.2778 71L 45.2745 45.2786 79L 45.2730 45.2756 49L 45.2715 45.2756 49L 45.2714 45.2740 33L
1250 49.2126 49.2077 49.2122 49.2148 4T 49.2115 49.2156 11T 49.2100 49.2126 26T 49.2085 49.2126 41T 49.2084 49.2110 42T
1400 55.1181 55.1118 55.1177 55.1208 90L 55.1169 55.1218 100L 55.1150 55.1181 63L 55.1132 55.1181 63L 55.1131 55.1162 44L
1600 62.9921 62.9858 62.9917 62.9948 4T 62.9909 62.9958 12T 62.9890 62.9921 31T 62.9872 62.9921 49T 62.9871 62.9902 50T
1800 70.8661 70.8582 70.8657 70.8693 111L 70.8648 70.8707 125L 70.8625 70.8661 79L 70.8602 70.8661 79L 70.8602 70.8638 56L
2000 78.7402 78.7323 78.7398 78.7434 4T 78.7389 78.7448 13T 78.7366 78.7402 36T 78.7343 78.7402 59T 78.7343 78.7379 59T
2300 90.5512 90.5414 90.5508 90.5551 137L 90.5499 90.5568 154L 90.5469 90.5512 98L 90.5443 90.5512 98L 90.5442 90.5485 71L
2500 98.4252 98.4154 98.4248 98.4291 4T 98.4239 98.4308 13T 98.4209 98.4252 43T 98.4183 98.4252 69T 98.4182 98.4225 70T
Note: T indicates tight fit. L indicates loose fit.
268
ISO Fits for Cast Iron and Steel Housings
Housing Bearing-Seat Diameters (Values in Inches)
Bearing M7 N6 N7 P6 P7
Outside
Diameter Housing Bore Fit Housing Bore Fit Housing Bore Fit Housing Bore Fit Housing Bore Fit
in in in in in
mm Min. Max. 0.0001" Min. Max. 0.0001" Min. Max. 0.0001" Min. Max. 0.0001" Min. Max. 0.0001"
16 0.6292 0.6299 3L 0.6291 0.6295 1T 0.6290 0.6297 1L 0.6289 0.6293 3T 0.6288 0.6295 1T
7T 8T 9T 10T 11T
19 0.7472 0.7480 0.7471 0.7476 0.7469 0.7477 0.7468 0.7473 0.7466 0.7474
21 0.8260 0.8268 0.8259 0.8264 0.8257 0.8265 0.8256 0.8261 0.8254 0.8262
22 0.8653 0.8661 0.8652 0.8657 0.8650 0.8658 0.8649 0.8654 0.8647 0.8655
24 0.9441 0.9449 4L 0.9440 0.9445 0 0.9438 0.9446 1L 0.9437 0.9442 3T 0.9435 0.9443 2T
26 1.0228 1.0236 8T 1.0227 1.0232 9T 1.0225 1.0233 11T 1.0224 1.0229 12T 1.0232 1.0230 14T
28 1.1016 1.1024 1.1015 1.1020 1.1013 1.1021 1.1012 1.1017 1.1010 1.1018
30 1.1803 1.1811 1.1802 1.1807 1.1800 1.1808 1.1799 1.1804 1.1797 1.1805
32 1.2588 1.2598 1.2587 1.2593 1.2585 1.2595 1.2583 1.2590 1.2581 1.2591
35 1.3770 1.3780 4L 1.3769 1.3775 1.3767 1.3777 1.3765 1.3772 1.3763 1.3773
37 1.4557 1.4567 10T 1.4556 1.4562 1T 1.4554 1.4564 1L 1.4552 1.4559 4T 1.4550 1.4560 3T
40 1.5738 1.5748 1.5737 1.5743 11T 1.5735 1.5745 13T 1.5733 1.5740 15T 1.5731 1.5741 17T
42 1.6525 1.6535 1.6524 1.6530 1.6522 1.6532 1.6520 1.6527 1.6518 1.6528
47 1.8494 1.8504 1.8493 1.8499 1.8491 1.8501 1.8489 1.8496 1.8487 1.8497
52 2.0460 2.0472 2.0459 2.0466 2.0457 2.0468 2.0454 2.0462 2.0452 2.0464
55 2.1642 2.1654 2.1641 2.1648 2.1639 2.1650 2.1636 2.1644 2.1634 2.1646
58 2.2823 2.2835 2.2822 2.2829 2.2820 2.2831 2.2817 2.2825 2.2815 2.2827
62 2.4397 2.4409 5L 2.4396 2.4403 2.4394 2.4405 2.4391 2.4399 2.4389 2.4401
65 2.5579 2.5591 12T 2.5578 2.5585 1T 2.5576 2.5587 1L 2.5573 2.5581 5T 2.5571 2.5583 3T
70 2.7547 2.7559 2.7546 2.7553 13T 2.7544 2.7555 15T 2.7541 2.7549 18T 2.7539 2.7551 20T
72 2.8334 2.8346 2.8333 2.8340 2.8331 2.8342 2.8328 2.8336 2.8326 2.8338
78 3.0697 3.0709 3.0696 3.0703 3.0694 3.0705 3.0691 3.0699 3.0689 3.0701
80 3.1484 3.1496 3.1483 3.1490 3.1481 3.1492 3.1478 3.1486 3.1476 3.1488
85 3.3451 3.3465 3.3450 3.3459 3.3447 3.3461 3.3445 3.3453 3.3442 3.3456
90 3.5419 3.5433 3.5418 3.5427 3.5415 3.5429 3.5413 3.5421 3.5410 3.5424
100 3.9356 3.9370 6L 3.9355 3.9364 0 3.9352 3.9366 2L 3.9350 3.9358 6T 3.9347 3.9361 3T
110 4.3293 4.3307 14T 4.3292 4.3301 15T 4.3289 4.3303 18T 4.3287 4.3295 20T 4.3284 4.3298 23T
115 4.5262 4.5276 4.5261 4.5270 4.5258 4.5272 4.5256 4.5264 4.5253 4.5267
120 4.7230 4.7244 4.7229 4.7238 4.7226 4.7240 4.7224 4.7232 4.7221 4.7235
125 4.9197 4.9213 4.9195 4.9205 4.9193 4.9208 4.9189 4.9199 4.9186 4.9202
130 5.1165 5.1181 5.1163 5.1173 5.1161 5.1176 5.1157 5.1167 5.1154 5.1170
135 5.3134 5.3150 7L 5.3132 5.3142 1T 5.3130 5.3145 2L 5.3126 5.3136 7T 5.3123 5.3139 4T
140 5.5102 5.5118 16T 5.5100 5.5110 18T 5.5098 5.5113 20T 5.5094 5.5104 24T 5.5091 5.5107 27T
145 5.7071 5.7087 5.7069 5.7079 5.7067 5.7082 5.7063 5.7073 5.7060 5.7076
150 5.9039 5.9055 5.9037 5.9047 5.9035 5.9050 5.9031 5.9041 5.9028 5.9044
160 6.2976 6.2992 10L 6.2974 6.2984 6.2972 6.2987 6.2968 6.2978 6.2965 6.2981
170 6.6913 6.6929 16T 6.6911 6.6921 2L 6.6909 6.6924 5L 6.6905 6.6915 4T 6.6902 6.6918 1T
180 7.0850 7.0866 7.0848 7.0858 18T 7.0846 7.0861 20T 7.0842 7.0852 24T 7.0839 7.0855 27T
190 7.4785 7.4803 7.4783 7.4794 7.4779 7.4797 7.4775 7.4787 7.4772 7.4790
200 7.8722 7.8740 7.8720 7.8731 7.8716 7.8734 7.8712 7.8724 7.8709 7.8727
210 8.2659 8.2677 8.2657 8.2668 8.2653 8.2671 8.2649 8.2661 8.2646 8.2664
215 8.4628 8.4646 12L 8.4626 8.4637 3L 8.4622 8.4640 6L 8.4618 8.4630 4T 8.4615 8.4633 1T
225 8.8565 8.8583 18T 8.8563 8.8574 20T 8.8559 8.8577 24T 8.8555 8.8567 28T 8.8552 8.8570 31T
240 9.4470 9.4488 9.4468 9.4479 9.4464 9.4482 9.4460 9.4472 9.4457 9.4475
250 9.8407 9.8425 9.8405 9.8416 9.8401 9.8419 9.8397 9.8409 9.8394 9.8412
260 10.2342 10.2362 10.2340 10.2352 10.2336 10.2356 10.2331 10.2343 10.2327 10.2348
270 10.6279 10.6299 10.6277 10.6289 10.6273 10.6293 10.6268 10.6280 10.6264 10.6285
280 11.0216 11.0236 14L 11.0214 11.0226 4L 11.0210 11.0230 8L 11.0205 11.0217 5T 11.0201 11.0222 0
300 11.8090 11.8110 20T 11.8088 11.8100 22T 11.8084 11.8104 26T 11.8079 11.8091 31T 11.8075 11.8096 35T
310 12.2027 12.2047 12.2025 12.2037 12.2021 12.2041 12.2016 12.2028 12.2012 12.2033
320 12.5962 12.5984 12.5960 12.5974 12.5955 12.5978 12.5950 12.5964 12.5945 12.5968
340 12.3836 12.3858 13.3834 13.3848 13.3829 13.3852 13.3824 13.3838 13.3819 13.3842
350 13.7773 13.7795 16L 13.7771 13.7785 6L 13.7766 13.7789 10L 13.7761 13.7775 4T 13.7756 13.7779 0
360 14.1710 14.1732 22T 14.1708 14.1722 24T 14.1703 14.1726 29T 14.1698 14.1712 34T 14.1693 14.1716 39T
380 14.9584 14.9606 14.9582 14.9596 14.9577 14.9600 14.9572 14.9586 14.9567 14.9590
400 15.7458 15.7480 15.7456 15.7470 15.7451 15.7474 15.7446 15.7460 15.7441 15.7464
420 16.5329 16.5354 16.5328 16.5343 16.5323 16.5347 16.5317 16.5332 16.5311 16.5336
440 17.3203 17.3228 18L 17.3202 17.3217 7L 17.3197 17.3221 11L 17.3191 17.3206 4T 17.3185 17.3210 0
460 18.1077 18.1102 25T 18.1076 18.1091 26T 18.1071 18.1095 31T 18.1065 18.1080 37T 18.1059 18.1084 43T
480 18.8951 18.8976 18.8950 18.8965 18.8945 18.8969 18.8939 18.8954 18.8933 18.8958
500 19.6825 19.6850 19.6824 19.6839 19.6819 19.6843 19.6813 19.6828 19.6807 19.6832
520 20.4686 20.4714 20.4689 20.4707 20.4679 20.4707 20.4676 20.4693 20.4666 20.4693
540 21.2560 21.2588 21.2563 21.2581 21.2553 21.2581 21.2550 21.2567 21.2540 21.2567
560 22.0434 22.0462 10L 22.0437 22.0455 3L 22.0427 22.0455 3L 22.0424 22.0441 11T 22.0414 22.0441 11T
580 22.8308 22.8336 38T 22.8311 22.8329 35T 22.8301 22.8329 45T 22.8298 22.8315 48T 22.8288 22.8315 58T
600 23.6182 23.6210 23.6185 23.6203 23.6175 23.6203 23.6172 23.6189 23.6162 23.6189
620 24.4056 24.4084 24.4059 24.4077 24.4049 24.4077 24.4046 24.4063 24.4036 24.4063
650 25.5863 25.5894 25.5867 25.5886 25.5855 25.5886 25.5852 25.5871 25.5840 25.5871
670 26.3737 26.3768 26.3741 26.3760 26.3729 26.3760 26.3726 26.3745 26.3714 26.3745
680 26.7674 26.7705 26.7678 26.7697 26.7666 26.7697 26.7663 26.7682 26.7651 26.7682
700 27.5548 27.5579 18L 27.5552 27.5571 10L 27.5540 27.5571 10L 27.5537 27.5556 5T 27.5525 27.5556 5T
720 28.3422 28.3453 43T 28.3426 28.3445 39T 28.3414 28.3445 51T 28.3411 28.3430 54T 28.3399 28.3430 66T
750 29.5233 29.5264 29.5237 29.5256 29.5225 29.5256 29.5222 29.5241 29.5210 29.5241
780 30.7044 30.7075 30.7048 30.7067 30.7036 30.7067 30.7033 30.7052 30.7021 30.7052
790 31.0981 31.1012 31.0985 31.1004 31.0973 31.1004 31.0970 31.0989 31.0958 31.0989
820 32.2786 32.2822 32.2791 32.2813 31.2778 32.2813 32.2774 32.2796 32.2760 32.2796
850 33.4597 33.4633 26L 33.4602 33.4624 33.4589 33.4624 33.4585 33.4607 33.4571 33.4607
870 34.2471 34.2507 49T 34.2476 34.2498 17L 34.2463 34.2498 17L 34.2459 34.2481 0 34.2445 34.2481 0
920 36.2156 36.2192 36.2161 36.2183 44T 36.2148 36.2183 57T 36.2144 36.2166 61T 36.2130 36.2166 75T
950 37.3967 37.4003 37.3972 37.3994 37.3959 37.3994 37.3955 37.3977 37.3941 37.3977
980 38.5778 38.5814 38.5783 38.5805 38.5770 38.5805 38.5766 38.5788 38.5752 38.5788
1000 39.3652 39.3688 39.3657 39.3679 39.3644 39.3679 39.3640 39.3662 39.3626 39.3662
1150 45.2699 45.2740 33L 45.2704 45.2730 23L 45.2689 45.2730 23L 45.2683 45.2709 2L 45.2667 45.2709 2L
1250 49.2069 49.2110 57T 49.2074 49.2100 52T 49.2059 49.2100 67T 49.2053 49.2079 73T 40.2037 49.2079 89T
1400 55.1113 55.1162 44L 55.1120 55.1150 32L 55.1101 55.1150 32L 55.1095 55.1126 8L 55.1077 55.1126 8L
1600 62.9853 62.9902 68T 62.9860 62.9890 61T 62.9841 62.9890 80T 62.9835 62.9866 86T 62.9817 62.9866 104T
1800 70.8579 70.8638 56L 70.8589 70.8625 43L 70.8566 70.8625 43L 70.8558 70.8594 12L 70.8535 70.8594 12L
2000 78.7320 78.7379 82T 78.7330 78.7366 72T 78.7307 78.7366 95T 78.7299 78.7335 103T 78.7276 78.7335 126T
2300 90.5416 90.5485 71L 90.5425 90.5469 55L 90.5400 90.5469 55L 90.5392 90.5435 21L 90.5366 90.5435 21L
2500 98.4156 98.4225 96T 98.4165 98.4209 87T 98.4140 98.4209 112T 98.4132 98.4175 120T 98.4106 98.4175 146T
Note: T indicates tight fit. L indicates loose fit.
269
Internal Radial Clearance Tolerances for
Single-Row Ball Bearings MRC Bearing Services
Bearing Series
ABMA
Metric C2 C0 C3 C4
Bore Inch Sizes
Sizes 30, 100K, MRC
Over Including R, 200, 300, TI ST LO XL
mm in mm in XLS 400, 1900 in (µm) in (µm) in (µm) in (µm)
2.5 — 10 — — 34-39 0-3 0-8 1-5 3-13 3-9 8-23 6-12* 15-30*
2.5 .0984 10 .3937 R2-R6 00 0-3 0-8 1-5 3-13 3-9 8-23 6-12* 15-30*
10 .3937 18 .7087 R8-R10 01-03 0-3.5 0-9 1-7 3-18 4-10 10-25 7-13 18-33
18 .7087 24 .9449 R12-R14 04 0-4 0-10 2-8 5-20 5-11 13-28 8-14 20-36
24 .9449 30 1.1811 R16-R18 05-06 0-4.5 0-11 2-8 5-20 5-11 13-28 9-16 23-41
30 1.1811 40 1.5748 R20 07-08 0-4.5 0-11 2-8 5-20 6-13 15-33 11-18 28-46
— 1.1811 — 1.5748 1³|₈–1¹|₂ — 0-4.5 0-11 2-8 5-20 6-13 15-33 11-18 28-46
40 1.5748 50 1.9665 1⁵|₈–1⁷|₈ 09-10 0-4.5 0-11 2-9 5-23 7-14 18-36 12-20 30-51
50 1.9685 65 2.5591 2–2¹|₂ 11-13 0-6 0-15 3-11 8-28 9-17 23-43 15-24 38-61
65 2.5591 80 3.1496 2⁵|₈–3¹|₈ 14-16 0-6 0-15 4-12 10-30 10-20 25-51 18-28 45-71
80 3.1496 100 3.9370 3¹|₄–3⁷|₈ 17-20 0-7 0-18 5-14 13-36 12-23 30-58 21-33 53-64
100 3.9370 120 4.7244 4–4⁵|₈ 21-24 0-8 0-20 6-16 15-41 14-26 36-66 24-38 61-97
120 4.7244 140 5.5118 4³|₄–5¹|₂ 26-28 0-9 0-23 7-19 18-48 16-32 41-81 28-45 71-114
140 5.5118 160 6.2992 5³|₈–6¹|₄ 30-32 0-9 0-23 7-21 18-53 18-36 46-91 32-51 81-130
160 6.2992 180 7.0866 6¹|₂–7 34-36 0-10 0-25 8-24 20-61 21-40 53-102 36-58 91-147
180 7.0866 200 7.8740 7¹|₄–7 ³|₄ 38-40 0-12 0-30 10-28 25-71 25-46 64-117 42-64 107-163
200 7.8740 220 8.6614 8–8¹|₂ 42-44 0-12 0-30 12-30 30-76 29-50 74-127 47-69 119-175
220 8.6614 240 9.4488 8³|₄–9 46-48 1-13 3-33 15-33 38-84 35-56 89-142 55-77 140-196
240 9.4485 260 10.2362 9¹|₂–10 50-52 2-14 5-36 18-36 45-91 42-63 107-160 64-86 163-218
260 10.2352 280 11.0236 10¹|₂–11 56 2-14 5-36 21-39 53-99 49-70 124-178 74-96 188-244
280 11.0236 300 11.8110 11¹|₂ 60 3-15 8-38 25-43 64-109 57-78 145-198 85-107 216-272
300 11.8110 320 12.5984 12 64 4-16 10-41 29-47 74-119 67-88 107-223 98-120 249-304
320 12.5984 340 13.3858 — — 4-16 10-41 33-51 84-130 78-99 198-251 113-135 287-343
340 13.3858 360 14.1732 — — 5-17 13-43 38-56 96-142 91-112 231-284 129-151 327-384
360 14.1732 380 14.9606 — — 6-18 15-46 43-61 109-155 106-127 269-323 149-171 378-434
380 14.9606 400 15.7480 — — 7-19 18-48 48-66 122-168 126-147 320-373 169-191 429-485
400 15.7480 420 16.5354 — — 7-19 18-48 54-72 137-183 148-169 376-429 193-215 490-546
420 16.5354 440 17.3223 — — 8-20 20-51 60-78 152-198 173-194 439-493 220-242 559-615
440 17.3223 460 18.1102 — — 9-21 23-53 67-85 170-216 202-223 513-566 251-273 638-693
460 18.1106 480 18.8976 — — 10-22 25-56 74-92 188-234 234-255 594-648 285-307 724-780
480 18.8976 500 19.6850 — — 12-24 30-61 82-100 208-254 269-290 683-737 326-348 828-884
*Not ABMA Value
270
Definition of Dynamic and
Static Radial Load Ratings
The size of a bearing to be used for an application is The basic dynamic radial load ratings of MRC
initially selected on the basis of its load carrying Bearings have been determined in accordance with
capacity in relation to the loads to be carried and the the latest ISO and ABMA standards and are based on
requirements regarding life and reliability. Numerical the material and manufacturing techniques used for
values of basic load ratings are used in calculations MRC standard production. They apply to radial loads
to express load carrying capacity. The basic dynamic acting on radial and angular contact bearings which
load rating C and the basic static load rating Co are are constant in magnitude and direction. For single
quoted in the bearing tables. All values expressed are row angular contact bearings, the radial load rating
radial ratings. refers to the radial component of that load which
causes a purely radial displacement of the bearing
Dynamic Radial Load Rating rings in relation to each other.
The basic dynamic load rating C is used for Static Radial Load Rating
calculations involving the selection of bearings which
rotate under load. It expresses the bearing radial The basic static radial load rating Co is used when
load which will give a basic rating life of one million bearings rotate at very slow speeds, are subjected
revolutions. The actual calculated life depends on the to very slow oscillations, or stationary under load.
magnitude of the imposed load. The imposed load It also must be considered when heavy shock loads
produces rolling element and raceway deformation of short duration act on a rotating bearing.
as illustrated in figure 1, resulting in tensile (t) and
compressive (c) stresses as each rolling element The basic static radial load rating is defined in
passes through the loaded zone. As these stress accordance with ISO and ABMA standards as the
cycles are repeated, as determined by the number static radial load which corresponds to a calculated
of revolutions of calculated life, sub-surface metal contact stress at the center of the most heavily loaded
fatigue cracks occur which eventually propagate to rolling element/raceway contact of 609000 PSI for
the raceway surface causing metal flaking, or spalling, all radial and angular contact ball bearings. For this
at which time the bearing has achieved its useful life. contact stress, a total permanent deformation of
rolling element and raceway occurs which is
approximately 0.0001 of the rolling element diameter
as shown in figure 2.
Figure 1 Figure 2
271
MRC Bearing Services
Definition of Bearing Life When bearings are stationary, rotate or oscillate very
slowly or subjected to heavy shock loads, the basic
The life of a rolling bearing is defined as the number static load rating (Co) must not be exceeded. As
of revolutions or the number of hours at a given speed specified in ABMA and ISO standards, the static load
which the bearing is capable of enduring before the rating is that load which produces a total permanent
first sign of fatigue failure occurs on one of its rings deformation of the rolling element or raceway which is
or rolling elements. approximately 0.0001 of the rolling element diameter.
Deformation greater than this amount may result in
The fatigue failure usually takes the form of surface noisy operation and premature failure.
Reliability % Lma a1
90 L10 1
95 L5 0.62
96 L4 0.53
97 L3 0.44
98 L2 0.33
99 L1 0.21
272
Speed Factors for Dynamic Load Ratings
The speed factors shown in the table below are used For speed factors at speeds not shown, use the
to convert the basic dynamic radial load rating (C) to following formula:
speeds other than 33 1 ⁄3 RPM, by multiplying C by
the speed factor. The values of C are listed in the
bearing dimension tables.
Speed Factor = 3.218 ( 1n )¹|₃
where n = operating RPM
Example:
Find dynamic radial load rating of 309S bearing at
2000 RPM
Basic dynamic radial loading rating (C) =11900 Lbs.
Speed factor at 2000 RPM = .255
Rating at 2000 RPM =11900 × .255 = 3035
RPM Factor RPM Factor RPM Factor RPM Factor RPM Factor RPM Factor RPM Factor
35 .9838 420 .4297 870 .3371 1 640 .2729 2 600 .2340 6 100 .1761 16 000 .1277
40 .9409 430 .4263 880 .3358 1 660 .2718 2 650 .2325 6 200 .1752 17 000 .1252
45 .9047 440 .4231 890 .3345 1 680 .2707 2 700 .2311 6 300 .1742 18 000 .1228
50 .8735 450 .4199 900 .3333 1 700 .2696 2 750 .2297 6 400 .1733 19 000 .1206
55 .8462 460 .4169 910 .3321 1 720 .2686 2 800 .2283 6 500 .1724 20 000 .1186
60 .8220 470 .4139 920 .3309 1 740 .2675 2 850 .2270 6 600 .1716 21 000 .1166
65 .8004 480 .4110 930 .3297 1 760 .2665 2 900 .2257 6 700 .1707 22 000 .1148
70 .7808 490 .4082 940 .3285 1 780 .2655 2 950 .2244 6 800 .1699 23 000 .1132
75 .7631 500 .4054 950 .3273 1 800 .2645 3 000 .2231 6 900 .1690 24 000 .1116
80 .7468 510 .4028 960 .3262 1 820 .2636 3 050 .2219 7 000 .1682 25 000 .1101
85 .7319 520 .4002 970 .3251 1 840 .2626 3 100 .2207 7 100 .1674 26 000 .1086
90 .7181 530 .3976 980 .3240 1 860 .2617 3 150 .2195 7 200 .1667 27 000 .1073
95 .7053 540 .3952 990 .3229 1 880 .2607 3 200 .2184 7 300 .1659 28 000 .1060
100 .6933 550 .3928 1 000 .3218 1 900 .2598 3 250 .2172 7 400 .1651 29 000 .1047
110 .6716 560 .3904 1 020 .3197 1 920 .2589 3 300 .2161 7 500 .1644 30 000 .1036
120 .6524 570 .3881 1 040 .3176 1 940 .2580 3 350 .2151 7 600 .1637 31 000 .1024
130 .6352 580 .3859 1 060 .3156 1 960 .2571 3 400 .2140 7 700 .1630 32 000 .1014
140 .6197 590 .3837 1 080 .3136 1 980 .2563 3 450 .2130 7 800 .1623 33 000 .1003
150 .6057 600 .3815 1 100 .3117 2 000 .2554 3 500 .2119 7 900 .1616 34 000 .0993
160 .5928 610 .3794 1 120 .3098 2 020 .2546 3 550 .2109 8 000 .1609 35 000 .0984
170 .5809 620 .3774 1 140 .3080 2 040 .2537 3 600 .2100 8 100 .1602 40 000 .0941
180 .5699 630 .3754 1 160 .3063 2 060 .2529 3 700 .2081 8 200 .1596 45 000 .0905
190 .5598 640 .3734 1 180 .3045 2 080 .2521 3 800 .2062 8 300 .1589 50 000 .0873
200 .5503 650 .3715 1 200 .3028 2 100 .2513 3 900 .2044 8 400 .1583 55 000 .0846
210 .5414 660 .3696 1 220 .3012 2 120 .2505 4 000 .2027 8 500 .1577 60 000 .0822
220 .5331 670 .3678 1 240 .2995 2 140 .2497 4 100 .2011 8 600 .1571 70 000 .0781
230 .5252 680 .3659 1 260 .2979 2 160 .2489 4 200 .1995 8 700 .1565 80 000 .0747
240 .5178 690 .3642 1 280 .2964 2 180 .2482 4 300 .1979 8 800 .1559 90 000 .0718
250 .5108 700 .3624 1 300 .2949 2 200 .2474 4 400 .1964 8 900 .1552 100 000 .0693
260 .5042 710 .3607 1 320 .2934 2 220 .2467 4 500 .1949 9 000 .1547
270 .4979 720 .3590 1 340 .2919 2 240 .2459 4 600 .1935 9 100 .1541
280 .4919 730 .3574 1 360 .2905 2 260 .2452 4 700 .1921 9 200 .1536
290 .4862 740 .3558 1 380 .2890 2 280 .2445 4 800 .1908 9 300 .1530
300 .4807 750 .3542 1 400 .2877 2 300 .2438 4 900 .1895 9 400 .1525
310 .4755 760 .3526 1 420 .2863 2 320 .2431 5 000 .1882 9 500 .1519
320 .4705 770 .3511 1 440 .2850 2 340 .2424 5 100 .1870 9 600 .1514
330 .4657 780 .3496 1 460 .2837 2 360 .2417 5 200 .1857 9 700 .1509
340 .4611 790 .3481 1 480 .2824 2 380 .2410 5 300 .1846 9 800 .1504
350 .4566 800 .3466 1 500 .2811 2 400 .2404 5 400 .1834 9 900 .1499
360 .4524 810 .3452 1 520 .2799 2 420 .2397 5 500 .1823 10 000 .1494
370 .4482 820 .3438 1 540 .2787 2 440 .2390 5 600 .1812 11 000 .1447
380 .4443 830 .3424 1 560 .2775 2 460 .2384 5 700 .1801 12 000 .1406
390 .4405 840 .3411 1 580 .2763 2 480 .2377 5 800 .1791 13 000 .1369
400 .4367 850 .3397 1 600 .2751 2 500 .2371 5 900 .1781 14 000 .1335
410 .4332 860 .3384 1 620 .2740 2 550 .2355 6 000 .1771 15 000 .1305
273
Speed Rating MRC Bearing Services
There is a limit to the speed at which rolling bearings the operational clearance in the bearing is reduced
can be operated. Generally it is the operating because of increased inner ring temperature, the final
temperature which can be permitted, with respect to consequence would be bearing seizure. Any increase
the lubricant being used or to the material of the in speed above the speed rating generally means that
bearing components, that sets the limit. The speed at the temperature difference between inner and outer
which this bearing temperature is reached depends on ring is greater than normal. Usually, therefore, an
the frictional heat generated in the bearing (including internal clearance greater than Normal (C3) is
any externally applied heat) and the amount of heat required, and it may be necessary to look more
which can be transported away from the bearing. closely at the temperature distribution in the bearing.
Bearing type and size, internal design, load,
lubrication and cooling conditions as well as cage The speed limit as defined by the speed rating is the
design, accuracy and internal clearance all play a part first limit to be reached with almost all bearing types.
in determining the permissible speed. Above this limit, other criteria have a stronger
influence, depending on bearing type. These criteria
Speed ratings include the form stability or strength of the cage,
Speed ratings for grease and oil lubrication are quoted lubrication of cage guiding surfaces, centrifugal and
in the bearing tables. The speed rating for a given gyratory forces acting on the rolling elements and
bearing represents the speed at which, under normal other speed-limiting factors.
loading conditions there is a balance between the
heat which can be removed from the bearing via the Another limit is set with grease lubrication by the
shaft and housing and sometimes via the lubricant grease used. The base oil viscosity and thickener
and the heat generated in the bearing by friction at determine the shear strength of the lubricant, which in
acceptable temperature interval above ambient. turn determines the permissible operating speed for
the particular bearing.
The speed ratings apply to bearings where the inner
ring rotates. Some reduction may be necessary where For high speed bearing arrangements, all
bearings are to operate with rotating outer ring. More components, particularly those which rotate, must
detailed information will be supplied on request. have a higher accuracy than normal to take account
of the vibrating behaviour. Special cage designs may
When heavier loads are applied to the bearing, the also be required and it is therefore advisable to
friction in the bearing will be increased so that the contact MRC Bearing Services.
bearing cannot be operated at such high speeds
as the speed rating would indicate unless higher For satisfactory bearing operation, especially at high
temperatures can be permitted. However, the speeds, a minimum load must be applied.
influence of heavier loads on the permissible speed
is generally only of importance for large bearings The speed ratings listed in the tables may be modified
(≥100mm). due to grade and cage variants. The multiplying
factors shown in the footnotes are based on historical
Speeds above the speed rating application and experience.
It is possible to operate bearings at speeds above the
speed ratings given in the bearing tables if the bearing
friction can be reduced by lubrication considerations
or when heat can be removed from the bearing by
circulating oil lubrication with cooling of the oil, by
cooling ribs on the housing or by directed cold air
streams. Any increase in speed above the speed
rating without taking any of these precautions would
only cause the temperature to rise excessively. An
increase of bearing temperature means that lubricant
viscosity is reduced and lubricant film formation is
made more difficult, thus leading to higher friction and
further temperature increases. If, at the same time,
274
275
276
Materials and Limitations
to the pure rotational are superimposed, particularly under lubricant starvation conditions permit continued
when conditions of high acceleration prevail. Suitable operation of the bearing for a time reducing the risk of
steps must be taken (e.g. oil lubrication) to ensure that seizure and secondary damage.
there is a sufficient supply of lubricant to the guiding
surfaces of the cage and to the inside of the bearing. When using bearings with polyamide cages the
permissible operating temperatures for the material and
Rolling bearing cages are mechanically stressed by its resistance to the lubricant used must be observed.
frictional, strain and inertia forces. They may also be At operating temperatures up to the values given in the
subjected to the chemical action of certain lubricants, adjacent table for the various oils and greases which
lubricant additives or products of their aging, organic are used as bearing lubricants, cage properties are
solvents, coolants (halogenated hydrocarbons, unaffected. If the permissible temperature is exceeded,
ammonia) etc. Thus the design and choice of material the cage material will age, this process being accelerated
are of paramount importance for the performance of the the longer the cage is exposed to the excessive
cage as well as for the operational reliability of the temperature. Brief periods at up to 70˚F (21˚C) above the
bearing as a whole. recommended maximum temperatures can be tolerated
provided they are interspersed with longer periods at
Standard Cages operating temperatures below the recommended values,
As rolling bearings have been developed various cage and provided the maximum operating temperature for
types and designs for the different bearing types and the lubricant is not exceeded. When operating
sizes have emerged; the cages differ as to form, temperatures are constantly above 250˚F (121˚C)
material, manufacturing methods, cost of production and bearings fitted with metallic cages are recommended.
operational limits. Molded polyamide cages are also unsuitable for
operating temperatures below -40˚F (-40˚C) as they lose
In the text preceding each section, information is their elasticity.
provided regarding the standard cages with which the
bearings are fitted and also the possible alternatives. The organic solvents normally used to clean rolling
The standard cage is always well proven in service and bearings such as white mineral spirits or trichloroethane
is the design considered most suitable for the majority of do not affect cage properties, nor do dilute alkaline
applications. With reference to the viability of production, cleaners (e.g. soda) if they are at room temperature and
the costs and the different application areas of the the period during which they are in contact is short. The
bearings, the standard cage for the larger bearings may chlorofluorocarbons or ammonia used in refrigeration do
be different from that for the smaller bearings in one and not attack polyamide. In vacuum, polyamide cages
the same series. If a bearing with a non-standard cage is become brittle because they become dehydrated.
required it is always advisable to check availability before
ordering. Permissible operating temperatures for cages of glass fibre reinforced
polyamide 6.6 with various bearing lubricants
Molded Polyamide Cages Lubricant Permissible
operating
For some bearing types, e.g. double row deep groove temperature1)
ball bearings, and angular contact ball bearings, the ˚C ˚F
small and medium-sized bearings are available with Mineral oils
molded cages of heat stabilized, glass fiber reinforced Oils without EP additives e.g. machine oils, hydraulic oils 120 248
EP oils e.g. industrial and automotive gearbox oils 110 230
polyamide 6.6. Heat stabilized, unfilled polyamide cages EP oils e.g. rear axle and differential gear oils (automotive),
are available for a limited number of sizes. This material hypoid gear oils 100 212
is characterized by a favorable combination of strength Synthetic oils
and elasticity. The good sliding properties of polyamide Polyglycols, poly-a-olefins 120 248
Diesters, silicones 110 230
on lubricated steel surfaces and the smoothness of the Phosphate esters 80 176
cage surfaces in contact with the rolling elements mean Greases
that little friction is generated by the cage so that heat Lithium base,2) polyurea, bentonite, calcium complex 120 248
generation and wear in the bearing are at a minimum. 1)
Measured on the outside surface of the outer ring.
The low density of the material means that the inertia 2)For sodium and calcium base greases and other bearing greases with a maximum oper-
ating temperature below 120˚C, the maximum temperature for the polyamide cage is the
of the cage is small. All these factors plus inherently same as the maximum temperature for the grease, otherwise the permissible operating
superior dynamic balance result in smoother and quieter temperature is 120˚C.
running bearings.
Steel Cages
The injection molding process used to produce the
cages allows functionally suitable designs to be made. Pressed cages of steel sheet are standard for many
The excellent running properties of polyamide cages deep groove ball bearings. These cages have relatively
278
Materials and Limitations
high strength and weigh little. To reduce friction and wear machined from cast or wrought material.Brass cages
they may be hardened and surface treated. High should not be used at temperatures in excess of 450˚F
strength, machined steel cages, often silver plated are (232˚C). They are unaffected by most of the commonly
also available for critical and extra heavy duty used bearing lubricants, including synthetic oils and
applications. greases, and can be cleaned using normal organic
solvents. The use of alkaline cleaning agents is not
Machined Bronze recommended. Ammonia (e.g. in refrigeration) causes
embrittlement in brass so that brass cages are
Machined bronze cages are used for heavy duty
unsuitable and other alternatives should be considered.
applications and larger size bearings. Machined bronze
cages can be used at operating temperatures up to Phenolic (Bakelite) Cages
450˚F (232˚C). They are not affected by the mineral or
synthetic oil based lubricants normally used for rolling Phenolic cages are used primarily for angular contact
bearings nor by the organic solvents used to clean ball bearings. These cages are composed of machined,
bearings. They are very resistant to corrosive attack. cotton fabric impregnated with phenolic resin. The light
weight construction of the phenolic cage makes it ideal
Brass Cages for high speed applicatons. Phenolic cages should not be
Pressed brass cages are used for some small and used in temperatures in excess of 225˚F (107˚C).
medium-sized bearings, but most brass cages are
279
Materials and Limitations MRC Bearing Services
SAE 52100 Vacuum processed high carbon chromium steel. 250˚F (121˚C) Max.
(AISI E-52100)
Special heat teatment increases maximum temperatures and improves Special Heat Treatment up to
Race Way dimensional stability.1) 400˚F (204˚C) Max.1)
Rings
440C martensitic stainless steel1) Moderate corrosive environments 300˚F (148˚C) Max.
and
Special Heat Treatment up to
Balls 800˚F (426˚C) Max.1)
M50 tool steel1) High temperature service, improved life at elevated temperatures 600˚F (315˚C) Max.
Nitrile Rubber Standard MRC seal material, identified by black color -70˚F to 250˚F
-56˚C to 121˚C
Seals Fluorocarbon seals (Viton®)1) Better temperature and chemical resistance, identified by grey or brown -40˚F to 400˚F
color -40˚C to 204˚C
PTFE Seals (Teflon®)1) Superior chemical and heat resistance, identified by tan color and -450˚F to 550˚F
‘‘woven’’ appearance -267˚C to 288˚C
1010 Low Carbon Steel Standard MRC shield material 450˚F (232˚C) Max.
Shields
302 Stainless Pressed Steel 1)
Corrosive environments 450˚F (232˚C) Max.
1010 Pressed Steel Standard MRC pressed cage material 450˚F (232˚C) Max.
Machined Phenolic (Bakelite) Composition made from a cotton fabric impregnated with phenolic resin; 225˚F (110˚C) Max.
two piece riveted or one piece machined design
Molded Polyamide Heat stabilized 6.6 polyamide. Identifiable by natural (cream color); 250˚F (121˚C) Max.
Ball Cages2) ball guided design
Molded Reinforced Polyamide Heat stabilized 6.6 polyamide reinforced with glass fiber; ball guided 250˚F (121˚C) Max.
design identifiable by dark grey color
(Separator)
302 Pressed Stainless Steel Corrosive environments; ball guided two piece riveted design 450˚F (232˚C) Max.
Pressed Brass Stamped one piece ball guided or two piece ball guided riveted design 450˚F (232˚C) Max.
4340 Machined Steel One piece land or ball guided design 575˚F (302˚C) Max.
Machined Bronze One piece land or ball guided design 450˚F (232˚C) Max.
1)
Contact MRC for availability
2)
Contact MRC for ball cages available for specific sizes.
280
Lubrication
281
Lubrication of Anti-Friction Bearings MRC Bearing Services
282
Lubrication of Anti-Friction Bearings
Friction Torque 3. Being a solid when not under shear, grease forms
an effective collar at bearing edges to help seal
The friction torque in an anti-friction bearing consists against dirt and water.
essentially of two components. One of these is a
function of the bearing design and the load imposed 4. With grease lubrication, leakage is minimized
on the bearing. The other is a function of the lubricant where contamination of products must be avoided.
type, the quantity, and the speed of the bearing. 5. During start-up periods, the bearing is instantly
It has been found that the friction torque in a bearing lubricated whereas with pressure or splash oil
is lowest with a quantity of the correct viscosity oil just systems, there can be a time interval during which
sufficient to form a film over the contacting surfaces. the bearing may operate before oil flow reaches the
The friction will increase with greater quantity and/or bearing.
high viscosity of the oil. With more oil than just Disadvantages
enough to make a film, the friction torque will also
increase with the speed. 1. Extreme loads at low speed or moderate loads at
Function of The Lubricant
high speed may create sufficient heat in the
bearing to make grease lubrication unsatisfactory.
1. To lubricate sliding contact between the cage and 2. Oil may flush debris out of the bearing. Grease will
other parts of the bearing. not.
2. To provide a film of oil between rolling contact 3. The correct amount of lubricant is not easily
surfaces (elastohydrodynamic lubrication). controlled as with oil.
3. To lubricate the sliding contact between the rolls Oil Characteristics
and guiding elements in roller bearings.
The ability of any oil to meet the requirements of
4. In some cases, to carry away the heat developed in specific operating conditions depends upon certain
the bearing. physical and chemical properties.
5. To protect the highly finished surfaces from Viscosity
corrosion.
The single most important property of oil is viscosity. It
6. To provide a sealing barrier against foreign matter.
Oil Versus Grease
is the relative resistance to flow. A high viscosity oil
will flow less readily than a thinner, low viscosity oil.
The ideal lubricant for rolling element bearings is oil. Lubrication Viscosity
Grease, formed by combining oil with soap or non- There are a number of instruments used for
soap thickeners, is simply a means of effecting determining the viscosity of oil. In the United States
greater utilization of the oil. In a grease, the thickener the instruments that are usually used are the
acts fundamentally as a carrier and not as a lubricant. Viscosimeter or the Viscometer. The Saybolt Universal
Greases are now used for lubricating by far the larger Viscosimeter measures the time in seconds required
number of rolling bearings. The extensive use of for 60cc of oil to drain through a standard hole at
grease has been dictated by the possibilities of some fixed temperature. When this unit is used the
simpler housing designs, less maintenance, less viscosities are quoted in terms of Saybolt Universal
difficulty with leakage, and better sealing against dirt. Seconds (SUS).
On the other hand, there are limitations which do not When the Kinematic Viscometer is used to measure
permit the use of grease. Where a lubricant must oil viscosity, the time required for a fixed amount of oil
dissipate heat rapidly, grease should not be used. In to flow through a calibrated capillary is used as an
many cases, associated machine elements that are oil intermediate value for calculating viscosity. The unit of
lubricated dictate the use of oil for anti-friction kinematic viscosity is the stoke or the centistoke (cSt).
bearings. Listed below are some of the advantages The common temperatures for reporting viscosity are
and disadvantages of grease lubrication. 104˚F and 212˚F (40˚C and 100˚C).
Advantages Generally, for ball bearings and cylindrical roller
1. Simpler housing designs are possible; piping is bearings, it is a good rule to select an oil which will
greatly reduced or eliminated. have a viscosity of at least 70 SUS (15 cSt) at
operating temperature.
2. Maintenance is greatly reduced since oil levels do
not have to be maintained.
283
Lubrication of Anti-Friction Bearings MRC Bearing Services
284
Lubrication of Anti-Friction Bearings
Oil may be supplied to anti-friction bearings in a higher operating temperature than ball bearings or
number of ways. These include bath oiling, oil mist cylindrical roller bearings under comparable operating
from an external supply, wick feed, drip feed, conditions.
circulating system, oil jet, and splash or spray from a
Example:
slinger or nearby machine parts.
A bearing having a bore diameter of 45 mm and an
One of the simplest methods of oil lubrication is to
outside diameter of 85 mm is required to operate at a
provide a bath of oil through which the rolling element
speed of 2000 rpm. The pitch diameter dm = 0.5
will pass during a portion of each revolution. Where
(d + D) = 0.5 (45 + 85) = 65 mm. As shown in Figure
cooling is required in high speed and heavily loaded
1, the intersection of dm = 65 mm with the oblique line
bearings, oil jets and circulating systems should be
representing 2000 rpm yields a minimum viscosity
considered. If necessary, the oil can be passed
required of 13 mm 2 /s. Now let us assume that the
through a heat exchanger before returning to the
operating temperature is 80˚C (176˚F). In Figure 2,
bearing.
the intersection between temperature 80˚C and
Selection of Oil required viscosity 13 mm 2 /s is between the oblique
lines for VG46 and VG68. Therefore, a lubricant with
The most important property of lubricating oil is the
the viscosity grade of at least VG46 should be used,
viscosity. Figures 1 and 2 should be used to assure
i.e. a lubricant of at least 46 mm 2 /s viscosity at the
that the viscosity is adequate in an application. Figure
standard reference temperature of 40˚C.
1 yields the minimum required viscosity as a function
of bearing size and rotational speed. When determining the operating temperature, it should
be kept in mind that the temperature of the oil is
The viscosity of a lubricating oil, however, varies with
usually 3˚ to 11˚C (5˚ to 20˚F) higher than that of the
temperature. It decreases with increasing
bearing housing. For example, assuming that the
temperature. Therefore, the viscosity at the operating
temperature of the bearing housing is 77˚C (170˚F),
temperature must be used, rather than the viscosity
the temperature of the oil will usually be 80˚ to 88˚C
grade (VG) which is based on the viscosity at the
(176˚ to 190˚F).
internationally standardized reference temperature of
40˚C (104˚F). Figure 2 can be used to determine the If a lubricant with higher than required viscosity is
actual viscosity at the operating temperature, which, selected, an improvement in bearing performance
however, varies with bearing design. For instance (life) can be expected.
tapered and spherical roller bearings usually have a
285
Lubrication of Anti-Friction Bearings MRC Bearing Services
1150 48
1075 46
8A 1000 250
925 44
850 42
775 40
700 38
8 680
625 36
550 34
500 140 32
150 Brt.
450 7 460 30
400 28
cSt @100°C
cSt @ 40°C
365 26
315 24
6 320
280 22
240 20
205 50 90 18
5 220
175 16
140 40 4 150 14
650 N
115 12
85W
500 N 30 3 100
85 10
60 300 N 2 68 80W 8
20
40 200 N 1 46 6
10W 32 75W
20 4
100 N 5W
22
10 2
288
Lubrication of Anti-Friction Bearings
This separation increases with higher storage operating at cold temperatures, an oil that has a
temperatures as the viscosity of the oil phase is sufficiently low pour point to remain fluid at the low
lowered. Oil separation, unless excessive, is not reason temperature and the proper viscosity for the operating
for rejection of a rolling bearing grease. Five percent is temperature should be chosen. If the oil is subjected to
typically permitted. Usually the separated oil can be low temperature start-up but operates at higher
easily stirred back into the grease body. temperatures, a high viscosity index is desirable.
The standard test method for determining oil separation Usually the most important consideration in selecting a
from grease during storage is ASTM D-1742. This is a grease for low temperature operation is start-up torque.
simple test where the sample is placed on a sieve Some greases may function satisfactorily during
strainer in a pressure cell with inlet air pressure operation but require excessive torque for start-up.
maintained at 0.25 PSI. The test is conducted at 77˚F Starting torque is not a function of the consistency or
(25˚C) and after 24 hours the separated oil that has the channeling properties of a grease. It appears to be
collected on the bottom of the cell is weighed and a function of the individual properties of the grease and
expressed as a percentage by weight of the original is difficult to measure. Experience alone will show
sample. This test is only intended to measure the whether one grease is better than another in this
tendency of a grease to separate oil during storage. It respect. Greases formulated with synthetic oils are
is not intended to predict the stability of grease under available which provide very low starting and running
dynamic service conditions. torque at temperatures as low as –100˚F (–73˚C).
Generally, a correctly selected grease provides lower
Channeling
torque than an oil.
Channeling is a term referring to the tendency of a
High Temperature
grease to separate and form a channel after the
passage of the balls and cage around the ball race. In oil lubricated bearing applications where ambient
Some greases channel very little and flow back rapidly temperatures are high, such as in ovens, some means
to fill the voids left by the rotating elements to cause of cooling is usually necessary to avoid excessive
higher torque and higher operating temperatures from bearing temperatures and premature lubricant failure.
the shear stresses within the lubricant. Poor channeling Some of the commonly used methods for decreasing
characteristics can make some greases unsatisfactory the oil temperature are cooling coils, water jackets, oil
for high speed operation when a channeling type cooling tanks, cooling discs, and fans.
grease will provide minimum torque and heat rise.
The rate of oxidation of lubricating fluids increases
Channeling type greases are usually of NLGI No. 3
rapidly with temperature rise. As mentioned earlier, the
or No. 4 consistency.
rate of oxidation doubles for each 18˚F (10˚C)
Special Properties temperature rise above 140˚F (60˚C). Above 250˚F
(121˚C), petroleum oils tend to oxidize rapidly and
There are many special grease formulations to meet
sometimes it becomes necessary to use special
a variety of unusual requirements. Special properties,
petroleum oils or synthetic oils to increase the service
which have been listed below, are often required in
life of the lubricant.
a grease. These special requirements may include:
1. Extra tackiness or adhesiveness to resist leakage Where the only heat is that generated by the bearing,
or throw-out. temperature rise can usually be held to a reasonable
level by the use of a suitable lubricant in proper
2. Proper structure for sealing to exclude contaminates.
quantity.
3. Resistance to the action of certain chemicals.
The high temperature limit for greases, i.e. the
4. Resistance to the action of solvents. maximum temperature at which a grease will provide a
5. Electrical conductivity. reasonable life in a non-relubricable bearing, is largely
6. Resistance to the effects of nuclear radiation. a function of the oxidation stability of the fluid and the
7. Resistance to the effects of high vacuum. thickener. The oxidation process is greatly accelerated
with increasing temperature. Another factor is
8. Non-toxic for use where there may be contact evaporation of the fluid phase. Also, greases thin out at
with food. high temperatures. If the grease consistency becomes
9. High oil bleed rates ≥ 2.5% for machined land too soft at operating temperatures there may be
guided cages leakage from the bearing.
Operating Conditions High Speeds
Low Temperature Small size anti-friction bearings are often successfully
grease lubricated at high speeds. Larger sizes usually
Oils and greases tend to thicken and resist flow as
require oil to remove heat as well as to lubricate.
temperatures are decreased. For oil lubricated bearings
289
Lubrication of Anti-Friction Bearings MRC Bearing Services
Where extensive cooling is required in high speed and Slow moving bearings can be packed full of a
heavily loaded bearings operating with high frictional cohesive, water resistant grease formulated with a
heat, oil jets and circulating systems should be very heavy oil to afford maximum protection against
considered. For small and medium size bearings large amounts of water.Where wet conditions are so
rotating at high speeds, an oil circulating system, drip severe that satisfactory protection cannot be provided
feed or oil mist is satisfactory. by a lubricant, it is sometimes necessary to use
bearings fabricated of special corrosion resistant
With other influences being equal, increasingly lower
alloys or bearings with corrosion resistant coatings.
viscosities are needed with increasing speeds. The
quantity of oil needed for successful operation Fretting
becomes greater with increasing temperature, load,
Anti-friction bearings are sometimes damaged by a
speed, and bearing size.
wear effect that is variously called fretting corrosion,
Extreme Pressures fretting, friction oxidation and false brinneling. This
effect evidences itself by the formation of rust-like
Various extreme pressure agents are compounded
wear debris and the formation of wear spots.
into some greases and oils. These include additives
such as sulfur, phosphorus, and chlorine compounds, Fretting can occur in bearings subjected to vibration,
graphite, and molybdenum disulfide. However, such vibratory loads, or oscillation of small amplitudes. It is
additives are generally not required in anti-friction sometimes seen in the bearings of idle machinery that
bearing lubricants and should be avoided unless their has been subjected to the vibrations of nearby
use is dictated by other associated equipment such as machines. The wear spots can be recognized as
gears. depressions or indentations in the races at the points
where they have been in contact with the balls or rolls.
For most applications, higher viscosity oils are
If allowed to progress, the wear in these contact areas
required to prevent metal to metal contact if pressures
will become so extensive as to prevent functioning of
are higher than normal or if shock loading occurs. In
the bearings.
cases where heavily loaded bearings operate at high
speeds, the selection of oil viscosity must be a Fretting can be eliminated or minimized by the
compromise between a heavy oil which is desirable selection of a lubricant which has good feed ability.
for heavy loading and a light oil which is desirable for Low viscosity oils minimize fretting to a greater extent
high speeds. than oils of higher viscosities.
Wet Conditions With grease lubrication in applications where fretting is
a problem, it is good general practice to use a soft
Whenever possible, an anti-friction bearing should be
grease such as an NLGI 0 or 1 grade or a harder
protected from water and moisture to avoid corrosion.
grease which tends to soften considerably upon
Even slight corrosion on the internal surfaces may
working.
initiate bearing failure.
Dust and Dirt
Ball and roller bearings are, however, often used
successfully where moisture is present. The presence A high percentage of ball and roller bearing troubles
of moisture will affect the choice of a grease with the can be attributed to foreign matter entering the
selection depending upon the quantity of moisture bearing after mounting. Because anti-friction bearings
present. are highly sensitive to dust and dirt, elaborate
protective devices are necessary in some
Water soluble sodium base greases will form a non-
applications.
corrosive emulsion when mixed with a limited quantity
of water. However, agitation is necessary to form this Oil lubricated bearings are generally protected from
emulsion. If water should enter an idle bearing, the foreign particle contamination by the use of oil filters
bearing may become corroded. There is a limit to the and the properly designed seals required in oil
amount of water which a water soluble grease can lubricated systems.
absorb and still protect the bearing surfaces.
Grease in sealed and shielded bearings can provide
A water resistant grease, such as a lithium base an effective barrier against dust and dirt. Where the
grease that contains an effective rust inhibitor should bearings operate in dusty or dirty atmosphere the
be used where large amounts of water are present. grease should be chosen with its sealing properties in
The term ‘‘water resistant grease’’ is actually a mind. Such a product should have good resistance to
misnomer since no grease will totally resist large structural break-down on working. Usually, the stiff
amounts of water for extended periods. consistency of an NLGI Grade 3 grease will provide a
good sealing barrier.
290
Lubrication of Anti-Friction Bearings
Relubrication interval
2.5 5
20
2 4
The following table gives the operating temperature
hours of operation
40
1.5 3
ranges for the types of grease normally used for 2.5
60
10 3
rolling bearing lubrication. The values are based on 2
80
100
120
7.5 1.5
extensive testing and are valid for commonly available
160
200
greases having a mineral oil base and no EP (extreme 5 10 3
240
4.5 9
280
pressure) additives. 4 8
360
3.5 7
420
3 6
600
2.5 5
Operating Temperature Ranges for Mineral Oil- 2 4
Based Greases 1.5 3
10 2 2
Grease Type Recommended Operating Temperature Range 7.5 1.5
(thickener) ˚C ˚F
50 10 2
Lithium base –30 to 110 –22 to 230 10 2 3 4 5 6 7 8 9 10 3 2 3 4 5 6 7 8 9 10 4 2
Lithium complex –20 140 –4 284
Sodium base –30 80 –22 176 n r/ min
Sodium complex –20 140 –4 284
Calcium base –10 60 14 140 Scale a: radial and angular contact ball bearings
Calcium complex –20 130 –4 266 Scale b: cylindrical roller bearings, needle roller bearings
Barium complex –20 130 –4 266
Aluminum complex –30 110 –22 230 Diagram 11
Diagram
Inorganic thickeners –30 130 –22 266
(bentonite, silica gel, etc.) Relubrication Interval—Grease
Polyurea –30 140 –22 284
The period during which a grease lubricated bearing
will function satisfactorily without relubrication is
Greases based on synthetic oils; e.g., ester oils,
dependent on the bearing type, size, speed, operating
synthetic hydrocarbons or silicone oils, may be used
temperature and the grease used. The relubrication
at temperatures above and below the operating
intervals (hours of operation) obtained from Diagram 1
temperature range of mineral oil-based greases. If
are valid for bearings in stationary machines where
grease-lubricated bearings are to operate at such
loading conditions are normal. The diagram is based
temperatures, MRC Bearings Applications
on the use of an age-resistant, average quality grease
Engineering should be contacted for advice.
and is valid for bearing temperatures of + 70˚C
measured on the outer ring. The intervals should be
halved for every 15˚C increase above + 70˚C, but the
maximum permissible operating temperature for the
grease should obviously not be exceeded. It should
be noted, however, that relubrication intervals may
vary significantly even where apparently similar
greases are used. For small bearings, particularly
deep groove ball bearings, the relubrication interval is
often longer than the life of the bearing application.
Relubrication is not, therefore, normally required. In
such cases, ball bearings fitted with shields or seals
and which are ‘‘lubricated-for-life’’ may be used.
291
Lubrication of Anti-Friction Bearings MRC Bearing Services
292
Lubrication of Anti-Friction Bearings
Cleaning Mounted Used Bearings preservative from the bearing surfaces when the
bearing will be lubricated with either a petroleum base
For cleaning bearings without removing them from
oil or grease.
their mounted assembly, hot, light oil at 180˚F (82˚C)
may be flushed through the housing while the shaft or It is possible that either synthetic oil or greases
spindle is slowly rotated. In cases of badly oxidized compounded with synthetic oils, will not be compatible
grease and oil, hot water emulsions can be used in with a petroleum base preservative. It is
place of flushing oil. The solution should be drained recommended that the preservative be removed from
thoroughly and the housing flushed with hot, light oil. the bearing surfaces before lubricating with either of
The shaft should be rotated slowly throughout these these products. Synthetic hydrocarbons are an
operations. exception. It is also possible that greases
compounded with a polyurea thickener may cause
In some cases where deposits are extremely difficult
excessive grease softening due to incompatibility with
to remove, an intermediate flushing with a mixture of
a petroleum base preservative.
alcohol and light petroleum solvent after the emulsion
treatment may be helpful. The flushing oil should be Synthetic oils and greases compounded with synthetic
drained completely and oil passages checked to make oils are classified as special condition lubricants. They
sure they are not clogged before adding new are usually not the best choice for operating
lubricant. conditions that fall within the capability of petroleum
base lubricants. They are expensive and lack some of
If the bearing is lubricated with grease, new grease
the desirable lubricating qualities of petroleum base
may be forced through the bearing to purge the old
lubricants. Synthetic hydrocarbon may be an
grease and contaminates. This may be done,
exception.
however, only if contamination is not severe and vent
openings are provided in the housing for exhausting Because machined phenolic or metal separators
the old grease. After purging with grease, the bearings occupy a considerable amount of the space between
should be operated for about ten minutes before the the bore of the outer ring and the OD of the inner ring
vent plugs are replaced to avoid serious over-heating in a bearing, special care must be exercised when
of the bearing due to churning of excess grease. introducing grease into these bearings to ensure that
it is uniformly distributed in the bearing. Operation of
Cleaning Sealed or Shielded Used Bearings
the bearing will eventually uniformly distribute the
Bearings which have non-removable double shields or grease, but it is possible to initiate a heating-type
seals cannot be cleaned. These bearings are normally failure or to cause damage to the active surfaces in
inspected and reused or rejected on the basis of the bearing before this occurs. This precaution is
smoothness and looseness. especially important when there is a close running
clearance between the separator and one of the rings.
Bearings having one seal or one shield may be
One method of introducing grease between the rings
cleaned satisfactorily by the methods outlined here.
and the separator is to use a plastic bag. If grease is
Bearings having two shields that are held in place by
sealed in a plastic bag and a small opening is cut
snap rings can be cleaned and regreased by carefully
across one of the corners, the bag can be inserted
removing the shields and reinstalling them.
between the separator and either ring. Grease can
Bearings having two removable rubber seals can be then be forced into the bearing by squeezing it from
cleaned and regreased if care is exercised in the bag.
removing and reinstalling the seals. The best
In applications where either water or air is used to
procedure for removing the seal is to insert a thin,
dissipate heat from the bearing cavity, care must be
knife-like blade between the O.D. of the seal and the
exercised not to create a significant temperature
seal groove in the outer ring, then slowly work around
differential between the bearing inner ring and outer
the periphery of the seal, working the seal from the
ring. Some cooling methods, i.e. water jacketed
groove. It is important to work around the periphery
housings, very efficiently dissipate heat from the
rather than exert too much pressure at one point
housing and outer ring of the bearing, but have little
which may damage the seal. Usually the seal can be
effect on the shaft and bearing inner ring. Under these
removed without damage.
conditions, internal clearance in the bearing is
Things You Should Know About Lubrication removed as the result of thermal expansion of the
inner ring and thermal contraction of the outer ring.
MRC bearings that have seals or shields are generally The loss of internal clearance can result in premature
lubricated for the life of the bearing. Bearings that do bearing failures due to a significant increase in ball
not have seals or shields are protected from corrosion and race stresses, and also due to excessive heat
by coating the bearing with a preservative. The generation. One way to avoid this problem is to
preservative is compatible with petroleum base oils circulate and cool the oil.
and lubricants. It is not necessary to remove the
293
Lubrication of Anti-Friction Bearings MRC Bearing Services
Figure 1
A simple oil bath method is satisfactory for low and Forced Feed Circulation
moderate speeds. The static oil level should not This type of system uses a circulating pump and is
exceed the center line of the lowermost ball or roller. particularly suitable for low to moderate speed, heavily
A greater amount of oil can cause churning which loaded applications where the oil has a major function
results in abnormally high operating temperatures. as a coolant in addition to lubrication. If necessary,
Systems of this type generally employ sight gages to the oil can be passed through a heat exchanger
facilitate inspection of the oil level. before returning to the bearing. Entry and exit of the
Figure 1 shows a constant level arrangement for oil should be on opposite sides of the bearing. An
maintaining the correct oil level. adequate drainage system must be provided to
prevent an excess accumulation of oil. Oil filters and
magnetic drain plugs should be used to minimize
contamination.
294
Lubrication of Anti-Friction Bearings
Figure 7
295
Lubrication of Anti-Friction Bearings MRC Bearing Services
Figure 10
Regreaseable Mounting
Recommended for moderate speeds and loads.
Where prelubricated sealed bearings are not suitable
for some reason, consideration must be given to use
of an open type bearing with provision for
relubrication. The grease plug at the bottom should be
removed while the grease is being inserted through
the fitting at the top. The direction of flow tends to
remove the old grease.
Figure 9
296
Lubrication of Anti-Friction Bearings
Figure 12
Figure 11
297
298
Bearing Vibration Data
299
MRC Ball Bearing Vibration Data
Data Based on a Speed of 1 RPM MRC Bearing Services
Values in Cycles per Minute
Inner Rotation Outer Rotation Inner or Outer Ring Rotation Inner Rotation Outer Rotation
Bearing Suffix Cage Speed Cage Speed Inner Ring Outer Ring Rolling Element Rolling Element
Size Frequency Frequency Frequency Frequency Frequency Frequency
(RPM) (RPM)
Inner Rotation Outer Rotation Inner or Outer Ring Rotation Inner Rotation Outer Rotation
Bearing Suffix Cage Speed Cage Speed Inner Ring Outer Ring Rolling Element Rolling Element
Size Frequency Frequency Frequency Frequency Frequency Frequency
(RPM) (RPM)
Inner Rotation Outer Rotation Inner or Outer Ring Rotation Inner Rotation Outer Rotation
Bearing Suffix Cage Speed Cage Speed Inner Ring Outer Ring Rolling Element Rolling Element
Size Frequency Frequency Frequency Frequency Frequency Frequency
(RPM) (RPM)
Inner Rotation Outer Rotation Inner or Outer Ring Rotation Inner Rotation Outer Rotation
Bearing Suffix Cage Speed Cage Speed Inner Ring Outer Ring Rolling Element Rolling Element
Size Frequency Frequency Frequency Frequency Frequency Frequency
(RPM) (RPM)
Inner Rotation Outer Rotation Inner or Outer Ring Rotation Inner Rotation Outer Rotation
Bearing Suffix Cage Speed Cage Speed Inner Ring Outer Ring Rolling Element Rolling Element
Size Frequency Frequency Frequency Frequency Frequency Frequency
(RPM) (RPM)
Inner Rotation Outer Rotation Inner or Outer Ring Rotation Inner Rotation Outer Rotation
Bearing Suffix Cage Speed Cage Speed Inner Ring Outer Ring Rolling Element Rolling Element
Size Frequency Frequency Frequency Frequency Frequency Frequency
(RPM) (RPM)
Inner Rotation Outer Rotation Inner or Outer Ring Rotation Inner Rotation Outer Rotation
Bearing Suffix Cage Speed Cage Speed Inner Ring Outer Ring Rolling Element Rolling Element
Size Frequency Frequency Frequency Frequency Frequency Frequency
(RPM) (RPM)
306
MRC Ball Bearing Vibration Data
Data Based on a Speed of 1 RPM
Values in Cycles per Minute
Inner Rotation Outer Rotation Inner or Outer Ring Rotation Inner Rotation Outer Rotation
Bearing Suffix Cage Speed Cage Speed Inner Ring Outer Ring Rolling Element Rolling Element
Size Frequency Frequency Frequency Frequency Frequency Frequency
(RPM) (RPM)
Inner Rotation Outer Rotation Inner or Outer Ring Rotation Inner Rotation Outer Rotation
Bearing Suffix Cage Speed Cage Speed Inner Ring Outer Ring Rolling Element Rolling Element
Size Frequency Frequency Frequency Frequency Frequency Frequency
(RPM) (RPM)
Inner Rotation Outer Rotation Inner or Outer Ring Rotation Inner Rotation Outer Rotation
Bearing Suffix Cage Speed Cage Speed Inner Ring Outer Ring Rolling Element Rolling Element
Size Frequency Frequency Frequency Frequency Frequency Frequency
(RPM) (RPM)
Inner Rotation Outer Rotation Inner or Outer Ring Rotation Inner Rotation Outer Rotation
Bearing Suffix Cage Speed Cage Speed Inner Ring Outer Ring Rolling Element Rolling Element
Size Frequency Frequency Frequency Frequency Frequency Frequency
(RPM) (RPM)
Inner Rotation Outer Rotation Inner or Outer Ring Rotation Inner Rotation Outer Rotation
Bearing Suffix Cage Speed Cage Speed Inner Ring Outer Ring Rolling Element Rolling Element
Size Frequency Frequency Frequency Frequency Frequency Frequency
(RPM) (RPM)
Inner Rotation Outer Rotation Inner or Outer Ring Rotation Inner Rotation Outer Rotation
Bearing Suffix Cage Speed Cage Speed Inner Ring Outer Ring Rolling Element Rolling Element
Size Frequency Frequency Frequency Frequency Frequency Frequency
(RPM) (RPM)
Inner Rotation Outer Rotation Inner or Outer Ring Rotation Inner Rotation Outer Rotation
Bearing Suffix Cage Speed Cage Speed Inner Ring Outer Ring Rolling Element Rolling Element
Size Frequency Frequency Frequency Frequency Frequency Frequency
(RPM) (RPM)
Inner Rotation Outer Rotation Inner or Outer Ring Rotation Inner Rotation Outer Rotation
Bearing Suffix Cage Speed Cage Speed Inner Ring Outer Ring Rolling Element Rolling Element
Size Frequency Frequency Frequency Frequency Frequency Frequency
(RPM) (RPM)
Inner Rotation Outer Rotation Inner or Outer Ring Rotation Inner Rotation Outer Rotation
Bearing Suffix Cage Speed Cage Speed Inner Ring Outer Ring Rolling Element Rolling Element
Size Frequency Frequency Frequency Frequency Frequency Frequency
(RPM) (RPM)
Inner Rotation Outer Rotation Inner or Outer Ring Rotation Inner Rotation Outer Rotation
Bearing Suffix Cage Speed Cage Speed Inner Ring Outer Ring Rolling Element Rolling Element
Size Frequency Frequency Frequency Frequency Frequency Frequency
(RPM) (RPM)
Inner Rotation Outer Rotation Inner or Outer Ring Rotation Inner Rotation Outer Rotation
Bearing Suffix Cage Speed Cage Speed Inner Ring Outer Ring Rolling Element Rolling Element
Size Frequency Frequency Frequency Frequency Frequency Frequency
(RPM) (RPM)
Inner Rotation Outer Rotation Inner or Outer Ring Rotation Inner Rotation Outer Rotation
Bearing Suffix Cage Speed Cage Speed Inner Ring Outer Ring Rolling Element Rolling Element
Size Frequency Frequency Frequency Frequency Frequency Frequency
(RPM) (RPM)
Inner Rotation Outer Rotation Inner or Outer Ring Rotation Inner Rotation Outer Rotation
Bearing Suffix Cage Speed Cage Speed Inner Ring Outer Ring Rolling Element Rolling Element
Size Frequency Frequency Frequency Frequency Frequency Frequency
(RPM) (RPM)
319
320
Snap-Ring, Groove and Housing Dimensions
1900 .041 .035 1.05 .90 .041 .031 1.05 .80 .819 .807 20.8 20.5 .008 .20 .984 25.0 .026 .65 .076 1.93 .094 2.5 1.016 25.8
1901 .041 .035 1.05 .90 .041 .031 1.05 .80 .898 .888 22.8 22.5 .008 .20 1.06 27.0 .026 .65 .076 1.93 .094 2.5 1.094 27.8
1902 .051 .045 1.30 1.15 .047 .037 1.20 .95 1.051 1.039 26.7 26.4 .010 .25 1.20 30.6 .031 .80 .078 1.98 .125 3.0 1.234 31.3
101K .068 .062 1.73 1.57 .047 .037 1.20 .95 1.050 1.040 26.7 26.4 .016 .40 1.20 30.6 .031 .80 .078 1.98 .125 3.0 1.234 31.3
1903 .051 .045 1.30 1.15 .047 .037 1.20 .95 1.130 1.118 28.7 28.4 .010 .25 1.28 32.5 .031 .80 .078 1.98 .125 3.0 1.312 33.3
200 .081 .075 2.06 1.90 .065 .053 1.65 1.35 1.109 1.099 28.2 27.9 .016 .40 1.36 34.5 .042 1.07 .125 3.18 .125 3.0 1.391 35.3
102K 201 .081 .075 2.06 1.90 .065 .053 1.65 1.35 1.187 1.177 30.2 29.0 .016 .40 1.44 36.5 .042 1.07 .125 3.18 .125 3.0 1.469 37.3
103K 202 300 .081 .075 2.06 1.90 .065 .053 1.65 1.35 1.306 1.296 33.2 32.9 .016 .40 1.55 39.3 .042 1.07 .125 3.18 .125 3.0 1.578 40.0
1904 .067 .061 1.70 1.55 .047 .037 1.20 .95 1.406 1.394 35.7 35.4 .010 .25 1.56 39.7 .031 .80 .078 1.98 .125 3.0 1.594 40.5
301 .081 .075 2.06 1.90 .065 .053 1.65 1.35 1.369 1.359 34.8 34.5 .016 .40 1.61 40.9 .042 1.07 .125 3.18 .125 3.0 1.641 41.7
203 .081 .075 2.06 1.90 .065 .053 1.65 1.35 1.500 1.490 38.1 37.9 .016 .40 1.75 44.5 .042 1.07 .125 3.18 .125 3.0 1.781 45.2
1905 .067 .061 1.70 1.55 .047 .037 1.20 .95 1.602 1.590 40.7 40.4 .010 .25 1.75 44.5 .031 .80 .078 1.98 .125 3.0 1.781 45.2
104K 302 .081 .075 2.06 1.90 .065 .053 1.65 1.35 1.565 1.555 39.8 38.5 .016 .40 1.81 46.0 .042 1.07 .125 3.18 .125 3.0 1.844 46.8
1906 .067 .061 1.70 1.55 .047 .037 1.20 .95 1.799 1.787 45.7 45.4 .010 .25 1.95 49.6 .031 .80 .078 1.98 .125 3.0 1.984 50.4
105K .081 .075 2.06 1.90 .065 .053 1.65 1.35 1.756 1.746 44.6 44.4 .016 .40 2.06 52.4 .042 1.07 .156 3.96 .125 3.0 2.094 53.2
204 303 .097 .091 2.46 2.31 .065 .053 1.65 1.35 1.756 1.746 44.6 44.4 .016 .40 2.06 52.4 .042 1.07 .156 3.96 .125 3.0 2.094 53.2
205 304 .097 .091 2.46 2.31 .065 .053 1.65 1.35 1.958 1.948 49.7 49.5 .016 .40 2.27 57.6 .042 1.07 .156 3.96 .188 5.0 2.297 58.3
1907 .067 .061 1.70 1.55 .047 .037 1.20 .95 2.114 2.102 53.7 53.4 .010 .25 2.28 57.9 .031 .80 .078 1.98 .188 5.0 2.312 58.7
106K .082 .074 2.08 1.88 .065 .053 1.65 1.35 2.071 2.061 52.8 52.4 .016 .40 2.38 60.3 .042 1.07 .156 3.96 .188 5.0 2.406 61.1
1908 .067 .061 1.70 1.55 .047 .037 1.20 .95 2.390 2.374 60.7 60.3 .010 .25 2.56 65.1 .031 .80 .078 1.98 .188 5.0 2.594 65.9
107K .082 .074 2.08 1.88 .087 .075 2.20 1.90 2.347 2.327 59.6 59.1 .024 .60 2.66 67.5 .065 1.65 .156 3.96 .188 5.0 2.688 68.3
206 305 .129 .121 3.28 3.07 .087 .075 2.20 1.90 2.347 2.327 59.6 59.1 .024 .60 2.66 67.5 .065 1.65 .156 3.96 .188 5.0 2.688 68.3
1909 .067 .061 1.70 1.55 .047 .037 1.20 .95 2.626 2.610 66.7 66.3 .010 .25 2.80 71.0 .031 .80 .078 1.98 .188 5.0 2.828 71.8
108K .098 .090 2.49 2.20 .087 .075 2.20 1.90 2.552 2.532 64.8 61.3 .024 .60 2.92 74.2 .065 1.65 .156 3.96 .188 5.0 2.984 75.8
1910 .067 .061 1.70 1.55 .047 .037 1.20 .95 2.783 2.769 70.7 70.3 .010 .25 2.95 75.0 .031 .80 .078 1.98 .188 5.0 2.984 75.8
207 306 .129 .121 3.28 3.07 .087 .075 2.20 1.90 2.709 2.689 68.8 68.3 .024 .60 3.08 78.2 .065 1.65 .188 4.78 .188 5.0 3.141 79.8
109K .098 .090 2.49 2.20 .087 .075 2.20 1.90 2.828 2.808 71.8 71.3 .024 .60 3.20 81.4 .065 1.65 .188 4.78 .188 5.0 3.266 83.0
1911 .083 .075 2.11 1.9 .063 .051 1.60 1.30 3.067 3.051 77.9 77.5 .016 .40 3.31 84.1 .042 1.07 .125 3.18 .188 5.0 3.375 85.7
110K .098 .090 2.49 2.20 .087 .075 2.20 1.90 3.024 3.004 76.8 76.3 .024 .60 3.40 86.5 .065 1.65 .188 4.78 .188 5.0 3.469 88.1
208 307 .129 .121 3.28 3.07 .087 .075 2.20 1.90 3.024 3.004 76.8 76.3 .024 .60 3.40 86.5 .065 1.65 .188 4.78 .188 5.0 3.469 88.1
1912 .083 .075 2.1 1.9 .063 .051 1.60 1.30 3.264 3.248 82.9 82.5 .016 .40 3.52 89.3 .042 1.07 .125 3.18 .188 5.0 3.578 90.9
209 .129 .121 3.28 3.07 .087 .075 2.20 1.90 3.221 3.201 81.8 81.3 .024 .60 3.59 91.3 .065 1.65 .188 4.78 .188 5.0 3.656 92.9
1913 .083 .075 2.1 1.9 .063 .051 1.60 1.30 3.461 3.445 87.9 87.5 .016 .40 3.70 94.1 .042 1.07 .125 3.18 .188 5.0 3.766 95.7
111K .113 .105 2.87 2.67 .118 .106 3.00 2.70 3.417 3.397 86.8 86.3 .024 .60 3.80 96.4 .095 2.41 .188 4.78 .188 5.0 3.859 98.0
210 308 .129 .121 3.28 3.07 .118 .106 3.00 2.70 3.417 3.397 86.8 86.3 .024 .60 3.80 96.4 .095 2.41 .188 4.78 .188 5.0 3.859 98.0
112K .113 .105 2.87 2.67 .118 .106 3.00 2.70 3.615 3.595 91.8 91.3 .024 .60 3.98 101.2 .095 2.41 .188 4.78 .188 5.0 4.047 102.9
1914 .098 .090 2.5 2.3 .063 .051 1.60 1.30 3.854 3.838 97.9 97.5 .016 .40 4.11 104.4 .042 1.07 .125 3.18 .188 5.0 4.172 106.0
113K .113 .105 2.87 2.67 .118 .106 3.00 2.70 3.811 3.791 96.8 96.3 .024 .60 4.19 106.4 .095 2.41 .188 4.78 .188 5.0 4.250 108.0
211 309 .129 .121 3.28 3.07 .118 .106 3.00 2.70 3.811 3.791 96.8 96.3 .024 .60 4.19 106.4 .095 2.41 .188 4.78 .188 5.0 4.250 108.0
321
Snap-Ring, Groove and Housing Dimensions MRC Bearing Services
1915 .098 .090 2.50 2.30 .063 .051 1.60 1.30 4.039 4.019 102.6 102.1 .016 .40 4.36 110.7 .042 1.07 .156 3.96 .188 5.0 4.422 112.3
1916 .098 .090 2.50 2.30 .063 .051 1.60 1.30 4.236 4.216 107.6 107.1 .016 .40 4.55 115.5 .042 1.07 .156 3.96 .188 5.0 4.609 117.1
114K .113 .105 2.87 2.67 .118 .106 3.00 2.70 4.205 4.185 106.8 106.3 .024 .60 4.58 116.3 .095 2.41 .188 4.78 .188 5.0 4.641 117.9
212 310 .129 .121 3.28 3.07 .118 .106 3.00 2.70 4.205 4.185 106.8 106.3 .024 .60 4.58 116.3 .095 2.41 .188 4.78 .188 5.0 4.641 117.9
115K .113 .105 2.87 2.67 .118 .106 3.00 2.70 4.402 4.382 111.9 111.3 .024 .60 4.78 121.4 .095 2.41 .188 4.78 .188 5.0 4.844 123.0
1917 .130 .122 3.30 3.10 .063 .051 1.60 1.30 4.630 4.610 117.6 117.1 .016 .40 4.94 125.4 .042 1.07 .156 3.96 .281 7.0 5.000 127.0
213 311 .160 .152 4.06 3.86 .134 .122 3.40 3.10 4.536 4.516 115.2 114.7 .024 .60 5.09 129.4 .109 2.77 .281 7.14 .281 7.0 5.156 131.0
1918 .130 .122 3.30 3.10 .063 .051 1.60 1.30 4.827 4.807 122.6 122.1 .016 .40 5.14 130.6 .042 1.07 .156 3.96 .281 7.0 5.203 132.2
116K .113 .105 2.87 2.67 .134 .122 3.40 3.10 4.733 4.713 120.2 119.7 .024 .60 5.30 134.5 .109 2.77 .281 7.14 .281 7.0 5.359 136.1
214 .160 .152 4.06 3.86 .134 .122 3.40 3.10 4.733 4.713 120.2 119.7 .024 .60 5.30 134.5 .109 2.77 .281 7.14 .281 7.0 5.359 136.1
1919 .130 .122 3.30 3.10 .063 .051 1.60 1.30 5.024 5.004 127.6 127.1 .016 .40 5.33 135.3 .042 1.07 .156 3.96 .281 7.0 5.391 136.9
117K .113 .105 2.87 2.67 .134 .122 3.40 3.10 4.930 4.910 125.2 124.7 .024 .60 5.50 139.7 .109 2.77 .281 7.14 .281 7.0 5.562 141.3
215 312 .160 .152 4.06 3.86 .134 .122 3.40 3.10 4.930 4.910 125.2 124.7 .024 .60 5.50 139.7 .109 2.77 .281 7.14 .281 7.0 5.562 141.3
1920 .130 .122 3.30 3.10 .087 .075 2.20 1.90 5.417 5.397 137.6 137.1 .024 .60 5.73 145.7 .065 1.65 .156 3.96 .281 7.0 5.797 147.2
118K .146 .136 3.71 3.45 .134 .122 3.40 3.10 5.324 5.304 135.2 134.7 .024 .60 5.89 149.6 .109 2.77 .281 7.14 .281 7.0 5.953 151.2
216 313 .193 .183 4.90 4.65 .134 .122 3.40 3.10 5.324 5.304 135.2 134.7 .024 .60 5.89 149.6 .109 2.77 .281 7.14 .281 7.0 5.953 151.2
1921 .130 .122 3.30 3.10 .087 .075 2.20 1.90 5.614 5.594 142.6 142.1 .024 .60 5.92 150.4 .065 1.65 .156 3.96 .281 7.0 5.984 152.0
119K .146 .136 3.71 3.45 .134 .122 3.40 3.10 5.521 5.501 140.2 139.7 .024 .60 6.08 154.4 .109 2.77 .281 7.14 .281 7.0 6.141 156.0
1922 .130 .122 3.30 3.10 .087 .075 2.20 1.90 5.811 5.791 147.6 147.1 .024 .60 6.13 155.6 .065 1.65 .156 3.96 .281 7.0 6.188 157.2
120K .146 .136 3.71 3.45 .134 .122 3.40 3.10 5.718 5.698 145.2 144.7 .024 .60 6.28 159.5 .109 2.77 .281 7.14 .281 7.0 6.344 161.1
217 314 .193 .183 4.90 4.65 .134 .122 3.40 3.10 5.718 5.698 145.2 144.7 .024 .60 6.28 159.5 .109 2.77 .281 7.14 .281 7.0 6.344 161.1
121K .146 .136 3.71 3.45 .134 .122 3.40 3.10 6.111 6.091 155.2 154.7 .024 .60 6.67 169.5 .109 2.77 .281 7.14 .281 7.0 6.734 171.0
218 315 .193 .183 4.90 4.65 .134 .122 3.40 3.10 6.111 6.091 155.2 154.7 .024 .60 6.67 169.5 .109 2.77 .281 7.14 .281 7.0 6.734 171.0
1924 .146 .138 3.70 3.50 .087 .075 2.20 1.90 6.370 6.350 161.8 161.3 .024 .60 6.75 171.5 .065 1.65 .188 4.78 .281 7.0 6.812 173.0
122K .146 .136 3.70 3.45 .150 .138 3.80 3.50 6.443 6.423 163.7 163.1 .024 .60 7.19 182.6 .120 3.05 .375 9.53 .375 10.0 7.250 184.2
219 316 .224 .214 5.69 5.44 .150 .138 3.80 3.50 6.443 6.423 163.7 163.1 .024 .60 7.19 182.6 .120 3.05 .375 9.53 .375 10.0 7.250 184.2
1926 .146 .138 3.70 3.50 .087 .075 2.20 1.90 6.961 6.941 176.8 176.3 .024 .60 7.34 186.5 .065 1.65 .188 4.78 .375 10.0 7.406 188.0
124K .146 .136 3.70 3.45 .150 .138 3.80 3.50 6.837 6.817 173.7 173.2 .024 .60 7.59 192.9 .120 3.05 .375 9.53 .375 10.0 7.656 194.5
220 317 .224 .214 5.69 5.44 .150 .138 3.80 3.50 6.837 6.817 173.7 173.2 .024 .60 7.59 192.9 .120 3.05 .375 9.53 .375 10.0 7.656 194.5
1928 .146 .138 3.70 3.50 .087 .075 2.20 1.90 7.354 7.334 186.8 186.3 .024 .60 7.73 196.5 .065 1.65 .188 4.78 .375 10.0 7.797 198.0
221 318 .224 .214 5.69 5.44 .150 .138 3.80 3.50 7.230 7.210 183.6 183.1 .024 .60 7.98 202.8 .120 3.05 .375 9.53 .375 10.0 8.047 204.4
126K 222 319 .224 .214 5.69 5.44 .150 .138 3.80 3.50 7.624 7.604 193.7 193.1 .024 .60 8.38 212.7 .120 3.05 .375 9.53 .375 10.0 8.438 214.3
128K .224 .214 5.69 5.44 .150 .138 3.80 3.50 8.018 7.998 203.7 203.2 .024 .60 8.77 222.7 .120 3.05 .375 9.53 .375 10.0 8.828 224.2
224 320 .224 .214 5.69 5.44 .150 .138 3.80 3.50 8.215 8.195 208.7 208.2 .024 .60 8.97 227.8 .120 3.05 .375 9.53 .375 10.0 9.031 229.4
130K 321 .224 .214 5.69 5.44 .150 .138 3.80 3.50 8.608 8.588 218.6 218.1 .024 .60 9.36 237.7 .120 3.05 .375 9.53 .375 10.0 9.422 239.3
226 .224 .214 5.69 5.44 .150 .138 3.80 3.50 8.805 8.785 223.7 223.1 .024 .60 9.56 242.9 .120 3.05 .375 9.53 .375 10.0 9.625 244.5
132K 322 .224 .214 5.69 5.44 .150 .138 3.80 3.50 9.199 9.179 233.7 233.2 .024 .60 9.95 252.8 .120 3.05 .375 9.53 .375 10.0 10.02 254.4
228 .224 .214 5.69 5.44 .150 .138 3.80 3.50 9.589 9.569 243.6 243.1 .024 .60 10.3 262.7 .120 3.05 .375 9.53 .375 10.0 10.41 264.3
230 .224 .214 5.69 5.44 .150 .138 3.80 3.50 10.38 10.36 263.6 263.0 .024 .60 11.1 282.6 .120 3.05 .375 9.53 .375 10.0 11.20 284.6
322
Snap-Ring, Groove and Housing Dimensions
203 .147 .139 3.73 3.53 .065 .053 1.65 1.35 1.500 1.490 38.1 37.9 .016 .40 1.75 44.5 .042 1.07 .125 3.18 .125 3.0 1.781 45.2
204 .187 .179 4.75 4.55 .065 .053 1.65 1.35 1.756 1.746 44.6 44.4 .016 .40 2.06 52.4 .042 1.07 .156 3.96 .125 3.0 2.094 53.2
205 304 .187 .179 4.75 4.55 .065 .053 1.65 1.35 1.958 1.948 49.7 49.5 .016 .40 2.27 57.6 .042 1.07 .156 3.96 .188 5.0 2.297 58.3
206 305 .181 .173 4.60 4.40 .087 .075 2.20 1.90 2.347 2.327 59.6 59.1 .024 .60 2.66 67.5 .065 1.65 .156 3.96 .188 5.0 2.688 68.3
207 306 .181 .173 4.60 4.40 .087 .075 2.20 1.90 2.709 2.689 68.8 68.3 .024 .60 3.08 78.2 .065 1.65 .188 4.78 .188 5.0 3.141 79.8
208 307 .181 .173 4.60 4.40 .087 .075 2.20 1.90 3.024 3.004 76.8 76.3 .024 .60 3.40 86.5 .065 1.65 .188 4.78 .188 5.0 3.469 88.1
209 .181 .173 4.60 4.40 .087 .075 2.20 1.90 3.221 3.201 81.8 81.3 .024 .60 3.59 91.3 .065 1.65 .188 4.78 .188 5.0 3.656 92.9
210 308 .179 .171 4.55 4.35 .118 .106 3.00 2.70 3.417 3.397 86.8 86.3 .024 .60 3.80 96.4 .095 2.41 .188 4.78 .188 5.0 3.859 98.0
211 309 .179 .171 4.55 4.35 .118 .106 3.00 2.70 3.811 3.791 96.8 96.3 .024 .60 4.19 106.4 .095 2.41 .188 4.78 .188 5.0 4.250 108.0
212 310 .179 .171 4.55 4.35 .118 .106 3.00 2.70 4.205 4.185 106.8 106.3 .024 .60 4.58 116.3 .095 2.41 .188 4.78 .188 5.0 4.641 117.9
213 311 .291 .283 7.39 7.19 .134 .122 3.40 3.10 4.536 4.516 115.2 114.7 .024 .60 5.09 129.4 .109 2.77 .281 7.14 .281 7.0 5.156 131.0
214 .291 .283 7.39 7.19 .134 .122 3.40 3.10 4.733 4.713 120.2 119.7 .024 .60 5.30 134.5 .109 2.77 .281 7.14 .281 7.0 5.359 136.1
215 312 .291 .283 7.39 7.19 .134 .122 3.40 3.10 4.930 4.910 125.2 124.7 .024 .60 5.50 139.7 .109 2.77 .281 7.14 .281 7.0 5.562 141.3
313 .315 .307 8.00 7.80 .134 .122 3.40 3.10 5.324 5.304 135.2 134.7 .024 .60 5.89 149.6 .109 2.77 .281 7.14 .281 7.0 5.953 151.2
314 .315 .307 8.00 7.80 .134 .122 3.40 3.10 5.718 5.698 145.2 144.7 .024 .60 6.28 159.5 .109 2.77 .281 7.14 .281 7.0 6.344 161.1
315 .315 .307 8.00 7.80 .134 .122 3.40 3.10 6.111 6.091 155.2 154.7 .024 .60 6.67 169.5 .109 2.77 .281 7.14 .281 7.0 6.784 171.0
323
Snap Ring Dimensions MRC Bearing Services
4 105 204 303 1.8504 1.756 1.741–.030 2.053 .042 .156 ¹|₈ ± ¹|₃₂
5 205 304 2.0472 1.958 1.943–.030 2.255 .042 .156 ¹|₈ ± ¹|₃₂
5a 106 2.1654 2.071 2.056–.030 2.368 .042 .156 ¹|₈ ± ¹|₃₂
6 107 206 305 403 2.4409 2.347 2.322–.030 2.634 .065 .156 ¹|₈ ± ¹|₃₂
6b 108 2.6772 2.616 2.591–.030 2.922 .065 .156 ¹|₈ ± ¹|₃₂
7 207 306 404 2.8346 2.709 2.684–.030 3.060 .065 .188 ¹|₈ ± ¹|₃₂
10 111 210 308 406 3.5433 3.417 3.392–.046 3.768 .095 .188 ⁵|₃₂ ± ³|₆₄
10a 112 3.7402 3.615 3.590–.046 3.966 .095 .188 ⁵|₃₂ ± ³|₆₄
11 113 211 309 407 3.9370 3.811 3.786–.046 4.162 .095 .188 ⁵|₃₂ ± ³|₆₄
12 114 212 310 408 4.3307 4.205 4.180–.062 4.556 .095 .188 ³|₁₆ ± ¹|₁₆
12a 115 4.5276 4.402 4.377–.062 4.753 .095 .188 ³|₁₆ ± ¹|₁₆
13 213 311 409 4.7244 4.536 4.506–.062 5.068 .109 .281 ³|₁₆ ± ¹|₁₆
14 116 214 4.9213 4.733 4.703–.062 5.265 .109 .281 ³|₁₆ ± ¹|₁₆
15 117 215 312 410 5.1181 4.930 4.900–.062 5.462 .109 .281 ³|₁₆ ± ¹|₁₆
16 118 216 313 411 5.5118 5.324 5.294–.093 5.856 .109 .281 ⁹|₃₂ ± ¹|₁₆
16a 119 5.7087 5.521 5.491–.093 6.053 .109 .281 ⁹|₃₂ ± ¹|₁₆
17 120 217 314 412 5.9055 5.718 5.688–.093 6.250 .109 .281 ⁹|₃₂ ± ¹|₁₆
18 121 218 315 413 6.2992 6.111 6.081–.093 6.643 .109 .281 ⁹|₃₂ ± ¹|₁₆
19 122 219 316 6.6929 6.443 6.413–.125 7.163 .120 .375 ³|₈ ± ¹|₁₆
20 124 220 317 414 7.0866 6.837 6.807–.125 7.557 .120 .375 ³|₈ ± ¹|₁₆
21 221 318 415 7.4803 7.230 7.200–.125 7.950 .120 .375 ³|₈ ± ¹|₁₆
22 126 222 319 416 7.8740 7.624 7.594–.125 8.344 .120 .375 ³|₈ ± ¹|₁₆
23 128 417 8.2677 8.018 7.987–.125 8.737 .120 .375 ³|₈ ± ¹|₁₆
24 224 320 8.4646 8.215 8.184–.125 8.934 .120 .375 ³|₈ ± ¹|₁₆
25 130 321 418 8.8583 8.608 8.578–.156 9.328 .120 .375 ¹⁵|₃₂ ± ³|₃₂
26 226 9.0551 8.805 8.775–.156 9.525 .120 .375 ¹⁵|₃₂ ± ³|₃₂
27 132 322 9.4488 9.199 9.168–.156 9.918 .120 .375 ¹⁵|₃₂ ± ³|₃₂
1) Snap-ring need not conform to cross section shown but all 4 corners must clear .016 max. fillet (snap rings 0 thru 5a) or
.024 (snap rings 6 thru 27).
2) Gap dimension and tolerance apply when snap ring bore ‘‘B’’ is nominal diameter shown (max. bore).
324
Bearing Accessories
Locknuts, Lockwashers and Lockplates
Locknuts and lockwashers are commonly used as
effective means for holding bearing inner rings axially
on the shaft. They are also frequently used to secure
gears, belt pulleys and other machine components.
The locknuts are accurately made to insure that the
abutment face will be square with the shaft axis, thus
avoiding distortion of the shaft during tightening.
The lockwashers are made from selected high quality
steel, heat treated, and they must pass a final
inspection that requires their finish to be smooth and
free from burrs.
The lockplate is a steel stamping that engages the
slot of the sleeve and is secured to the end face of
larger nuts by two screws. This unit is used in place of
lockwashers.
Wherever bearings must be held in permanent or
correct position, use locknuts, lockwashers and
lockplates.
Removable Sleeves and Removal Nuts
Removable sleeves have a taper on the outside
diameter corresponding to the taper in the bore of the
bearings. These sleeves are used for applications
where bearings must be removed occasionally for the
inspection of machine parts and at the same time will
be positively located on the shaft with the equivalent
of a press fit. A removal nut is used to remove the
sleeve from the bearing. In assembling, the sleeve is
locked on a threaded shaft by means of locknuts,
lockwashers and lockplates.
Adapters
The adapter is used to hold and locate a tapered bore
bearing on a cylindrical seat. It permits relatively wide
tolerances for the shaft diameter and makes it
unnecessary to heat the bearing or use a press when
mounting in order to obtain an interference fit of the
inner race on the shaft. Adapters are manufactured
with the same precise techniques and care used in
the manufacture of bearings.
325
Locknuts & Lockwashers for Ball Bearings
ABMA Standards MRC Bearing Services
Locknut Lockwasher
Lock Nominal Outside Thickness Face Diameter Lock Thickness
Nut Bearing Diameter L E Washer T
No. Bore Dia. D1 No.
+.13 +.005 Min. Max. Min. Max.
–.38 –.015
mm in mm in mm in mm in mm in mm in mm in
N00 10 .3937 19.0 ³|₄ 5.31 .209 5.81 .229 15.4 .605 15.9 .625 W00 1.07 .042
N01 12 .4724 22.2 ⁷|₈ 7.70 .303 8.20 .323 17.8 .699 18.3 .719 W01 1.07 .042
N02 15 .5906 25.4 1 7.70 .303 8.20 .323 20.1 .793 20.7 .813 W02 1.07 .042
N03 17 .6693 28.6 1¹|₈ 8.48 .334 8.99 .354 23.3 .918 23.8 .938 W03 1.07 .042
N04 20 .7874 34.9 1³|₈ 9.27 .365 9.78 .385 28.1 1.105 28.6 1.125 W04 1.07 .042
N05 25 .9843 39.7 1⁹|₁₆ 10.1 .396 10.6 .416 32.0 1.261 32.5 1.281 W05 1.27 .050
N06 30 1.1811 44.4 1³|₄ 10.1 .396 10.6 .416 37.6 1.480 38.1 1.500 W06 1.27 .050
N07 35 1.3780 52.4 2¹|₁₆ 10.9 .428 11.4 .448 45.5 1.793 46.1 1.813 W07 1.27 .050
N08 40 1.5748 57.2 2¹|₄ 10.9 .428 11.4 .448 50.3 1.980 50.8 2.000 W08 1.47 .058
N09 45 1.7717 64.3 2¹⁷|₃₂ 10.9 .428 11.4 .448 57.4 2.261 57.9 2.281 W09 1.47 .058
N10 50 1.9685 68.3 2¹¹|₁₆ 12.4 .490 13.0 .510 61.4 2.418 61.9 2.438 W10 1.47 .058
N11 55 2.1654 75.4 2³¹|₃₂ 12.4 .490 13.0 .510 67.0 2.636 67.5 2.656 W11 1.60 .063
N12 60 2.3622 80.2 3⁵|₃₂ 13.2 .521 13.7 .541 71.7 2.824 72.2 2.844 W12 1.60 .063
N13 65 2.5591 85.7 3³|₈ 14.0 .553 14.6 .573 77.3 3.043 77.8 3.063 W13 1.60 .063
N14 70 2.7559 92.1 3⁵|₈ 14.0 .553 14.6 .573 83.4 3.283 84.2 3.313 W14 1.60 .063
AN15 75 2.9528 98.4 3⁷|₈ 14.8 .584 15.3 .604 89.7 3.533 90.5 3.563 W15 1.83 .072
AN16 80 3.1496 105.6 4⁵|₃₂ 14.8 .584 15.3 .604 96.9 3.814 97.6 3.844 W16 1.83 .072
AN17 85 3.3465 111.9 4¹³|₃₂ 15.6 .615 16.1 .635 101.6 4.001 102.4 4.031 W17 1.83 .072
AN18 90 3.5433 118.3 4²¹|₃₂ 17.2 .678 17.7 .698 108.0 4.251 108.7 4.281 W18 2.39 .094
AN19 95 3.7402 125.4 4¹⁵|₁₆ 18.0 .709 18.5 .729 115.1 4.533 115.9 4.563 W19 2.39 .094
AN20 100 3.9370 131.8 5³|₁₆ 18.7 .735 19.3 .760 121.5 4.783 122.3 4.813 W20 2.39 .094
AN21 105 4.1339 138.1 5⁷|₁₆ 18.7 .735 19.3 .760 126.2 4.970 127.0 5.000 W21 2.39 .094
AN22 110 4.3307 145.3 5²³|₃₂ 19.5 .766 20.1 .791 133.4 5.251 134.1 5.281 W22 3.18 .125
AN24 120 4.7244 155.6 6¹|₈ 20.3 .798 20.9 .823 143.7 5.658 144.5 5.688 W24 3.18 .125
AN26 130 5.1181 171.4 6³|₄ 21.8 .860 22.5 .885 156.4 6.158 157.2 6.188 W26 3.18 .125
AN28 140 5.5118 180.2 7³|₃₂ 23.4 .923 24.1 .948 165.1 6.501 165.9 6.531 W28 3.18 .125
AN30 150 5.9055 195.3 7¹¹|₁₆ 24.2 .954 24.9 .979 178.6 7.033 179.4 7.063 W30 3.96 .156
AN32 160 6.2992 204.8 8¹|₁₆ 25.8 1.016 26.4 1.041 187.9 7.398 188.9 7.438 W32 3.96 .156
AN34 170 6.6929 219.9 8²¹|₃₂ 26.6 1.048 27.3 1.073 203.0 7.991 204.0 8.031 W34 3.96 .156
AN36 180 7.0866 230.2 9¹|₁₆ 27.4 1.079 28.0 1.104 211.7 8.335 212.7 8.375 W36 3.96 .156
AN38 190 7.4803 240.5 9¹⁵|₃₂ 28.2 1.110 28.8 1.135 222.0 8.741 223.0 8.781 W38 3.96 .156
AN40 200 7.8740 250.0 9²⁷|₃₂ 29.8 1.173 30.4 1.198 231.5 9.116 232.6 9.156 W40 3.96 .156
N44 220 8.6614 279.4 11 31.2 1.230 32.0 1.260 249.0 9.803 250.0 9.843 W44 3.96 .156
326
Shaft Dimensions for Lock Nuts
Threads—American (National) Standard Form, Fine Pitch Class 3 Fit
N00 32 9.93 .391 9.794 .3856 9.416 .3707 9.350 .3681 7.1 ⁹|₃₂ 1.6 ¹|₁₆ 2.4 ³|₃₂ 3.2 ¹|₈
N01 32 11.91 .469 11.775 .4636 11.397 .4487 11.331 .4461 9.5 ³|₈ 1.6 ¹|₁₆ 2.4 ³|₃₂ 3.2 ¹|₈
N02 32 14.88 .586 14.747 .5806 14.369 .5657 14.293 .5627 9.5 ³|₈ 2.0 ⁵|₆₄ 2.4 ³|₃₂ 3.2 ¹|₈
N03 32 16.87 .664 16.728 .6586 16.350 .6437 16.274 .6407 10.3 ¹³|₃₂ 2.0 ⁵|₆₄ 2.4 ³|₃₂ 3.2 ¹|₈
N04 32 19.84 .781 19.700 .7756 19.322 .7607 19.235 .7573 11.1 ⁷|₁₆ 2.0 ⁵|₆₄ 2.4 ³|₃₂ 4.8 ³|₁₆
N05 32 24.61 .969 24.475 .9636 24.097 .9487 24.011 .9453 11.9 ¹⁵|₃₂ 2.4 ³|₃₂ 3.2 ¹|₈ 4.8 ³|₁₆
N06 18 29.79 1.173 29.586 1.1643 28.877 1.1369 28.776 1.1329 11.9 ¹⁵|₃₂ 2.4 ³|₃₂ 3.2 ¹|₈ 4.8 ³|₁₆
N07 18 34.95 1.376 34.742 1.3678 34.034 1.3399 33.932 1.3359 12.7 ¹|₂ 2.4 ³|₃₂ 3.2 ¹|₈ 4.8 ³|₁₆
N08 18 39.70 1.563 39.492 1.5548 38.783 1.5269 38.669 1.5224 13.5 ¹⁷|₃₂ 2.4 ³|₃₂ 3.2 ¹|₈ 7.9 ⁵|₁₆
N09 18 44.88 1.767 44.674 1.7588 43.965 1.7309 43.851 1.7264 13.5 ¹⁷|₃₂ 2.4 ³|₃₂ 4.0 ⁵|₃₂ 7.9 ⁵|₁₆
N10 18 49.96 1.967 49.754 1.9588 49.045 1.9309 48.931 1.9264 15.1 ¹⁹|₃₂ 2.4 ³|₃₂ 4.0 ⁵|₃₂ 7.9 ⁵|₁₆
N11 18 54.79 2.157 54.580 2.1488 53.871 2.1209 53.741 2.1158 15.1 ¹⁹|₃₂ 3.2 ¹|₈ 4.0 ⁵|₃₂ 7.9 ⁵|₁₆
N12 18 59.94 2.360 59.736 2.3518 59.027 2.3239 58.898 2.3188 15.9 ⁵|₈ 3.2 ¹|₈ 4.0 ⁵|₃₂ 7.9 ⁵|₁₆
N13 18 64.72 2.548 64.511 2.5398 63.802 2.5119 63.673 2.5068 16.7 ²¹|₃₂ 3.2 ¹|₈ 4.0 ⁵|₃₂ 7.9 ⁵|₁₆
N14 18 69.88 2.751 69.667 2.7428 68.959 2.7149 68.829 2.7098 16.7 ²¹|₃₂ 3.2 ¹|₈ 6.4 ¹|₄ 7.9 ⁵|₁₆
AN15 12 74.50 2.933 74.214 2.9218 73.124 2.8789 72.987 2.8735 17.5 ¹¹|₁₆ 3.2 ¹|₈ 6.4 ¹|₄ 7.9 ⁵|₁₆
AN16 12 79.68 3.137 79.395 3.1258 78.306 3.0829 78.156 3.0770 17.5 ¹¹|₁₆ 3.2 ¹|₈ 6.4 ¹|₄ 9.5 ³|₈
AN17 12 84.84 3.340 84.552 3.3288 83.462 3.2859 83.274 3.2785 18.3 ²³|₃₂ 3.2 ¹|₈ 6.4 ¹|₄ 9.5 ³|₈
AN18 12 89.59 3.527 89.301 3.5153 88.212 3.4729 88.024 3.4655 20.6 ¹³|₁₆ 4.0 ⁵|₃₂ 6.4 ¹|₄ 9.5 ³|₈
AN19 12 94.74 3.730 94.458 3.7188 93.368 3.6759 93.180 3.6685 21.4 ²⁷|₃₂ 4.0 ⁵|₃₂ 6.4 ¹|₄ 9.5 ³|₈
AN20 12 99.52 3.918 99.233 3.9068 98.143 3.8639 97.955 3.8565 22.2 ⁷|₈ 4.0 ⁵|₃₂ 7.9 ⁵|₁₆ 9.5 ³|₈
AN21 12 104.70 4.122 104.415 4.1108 103.325 4.0679 103.114 4.0596 22.2 ⁷|₈ 4.0 ⁵|₃₂ 7.9 ⁵|₁₆ 9.5 ³|₈
AN22 12 109.86 4.325 109.571 4.3138 108.481 4.2709 108.270 4.2626 23.0 ²⁹|₃₂ 4.8 ³|₁₆ 7.9 ⁵|₁₆ 9.5 ³|₈
AN24 12 119.79 4.716 119.502 4.7048 118.412 4.6619 118.202 4.6536 23.8 ¹⁵|₁₆ 4.8 ³|₁₆ 7.9 ⁵|₁₆ 9.5 ³|₈
AN26 12 129.69 5.106 129.408 5.0948 128.319 5.0519 128.108 5.0436 25.4 1 4.8 ³|₁₆ 7.9 ⁵|₁₆ 12.7 ¹|₂
AN28 12 139.62 5.497 139.340 5.4858 138.250 5.4429 138.039 5.4346 27.0 1¹|₁₆ 4.8 ³|₁₆ 7.9 ⁵|₁₆ 15.9 ⁵|₈
AN30 12 149.56 5.888 149.271 5.8768 148.181 5.8339 147.971 5.8256 28.6 1¹|₈ 5.6 ⁷|₃₂ 9.5 ³|₈ 15.9 ⁵|₈
AN32 8 159.61 6.284 159.228 6.2638 157.551 6.2028 157.320 6.1937 30.2 1³|₁₆ 6.0 ¹⁵|₆₄ 9.5 ³|₈ 15.9 ⁵|₈
AN34 8 169.14 6.659 168.753 6.6438 167.076 6.5778 166.845 6.5687 31.0 1⁷|₃₂ 6.0 ¹⁵|₆₄ 9.5 ³|₈ 19.1 ³|₄
AN36 8 179.48 7.066 179.091 7.0508 177.414 6.9848 177.183 6.9757 31.8 1¹|₄ 6.0 ¹⁵|₆₄ 9.5 ³|₈ 19.1 ³|₄
AN38 8 189.79 7.472 189.403 7.4568 187.727 7.3908 187.496 7.3817 32.5 1⁹|₃₂ 6.0 ¹⁵|₆₄ 9.5 ³|₈ 19.1 ³|₄
AN40 8 199.31 7.847 198.928 7.8318 197.252 7.7658 196.962 7.7544 34.1 1¹¹|₃₂ 6.0 ¹⁵|₆₄ 9.5 ³|₈ 22.2 ⁷|₈
N44 8 219.15 8.628 218.766 8.6128 217.089 8.5468 216.782 8.5347 34.9 1³|₈ 9.5 ³|₈ 4.8 ³|₁₆ 27.0 1¹|₁₆
*Z = Minimum bearing width – .016 ± .010 in
– .406 ± .254mm
327
Locknut Torque MRC Bearing Services
328
Installation Procedures
For the precision ball and roller bearings supplied by Bearings which have become contaminated
MRC Bearings, skill and cleanliness while handling, because of improper handling (damaged package,
mounting and dismounting are necessary to ensure etc.) must be carefully washed and dried before
satisfactory bearing performance. As precision mounting.
components, rolling bearings must be handled with
Bearings which are supplied ready-greased and
appropriate care during transportation, storage,
which have seals, shields or polymerized lubricant
mounting and dismounting. For example, it is well
must never be washed before mounting.
known that minute dents, and small amounts of
contact surface corrosion and contaminants will Bearing Mounting
seriously shorten bearing endurance.
The method (mechanical, hydraulic or thermal) used
Such damages can be caused by improper handling. to mount a bearing depends on the type and size of
the bearing and complexity of the application
Bearing Storage and Transportation
assembly.
Before packaging, MRC precision bearings are treated
In all cases, it is extremely important that neither the
with a high-grade preservative and they should be
bearing, nor any of its components (rings, cage or
stored in the original, unbroken package. The relative
rolling elements), receive any impact loading (hammer
humidity in the storage room should not exceed
blows, etc.) as this would damage the bearing and
60%. When transporting bearings into and out of the
could dislodge components. Also, under no
storage room, care must be exercised not to drop the
circumstances must pressure be applied to one ring in
bearings nor apply heavy or even moderate impact
order to mount the other ring.
loading of any kind to prevent damage to, or
dislodging of, any of the bearing components. Also With non-separable bearings, the ring which is to have
care must be exercised to assure the package the tighter fit is generally mounted first. The seating
remains unbroken to prevent contaminants from being surface should be lightly oiled before mounting.
introduced into the bearings. Pressure may be uniformly applied against a sleeve
abutting the bearing ring face; the use of a mounting
Preparations for Bearing Mounting
dolly instead of a sleeve, as shown in Figure 1,
Mounting should be carried out in a dry, dust free permits a mounting force to be applied centrally.
room away from metal-working or other machines
producing swarf and dust and operating with
contaminating agents. Before mounting the bearings,
all the necessary parts, tools and equipment should
be at hand. It is also important that any drawings or
instructions be studied to determine the correct order
in which the various components are to be mounted.
All components of the bearing arrangement (housings,
shafts, etc.) must be carefully cleaned and any burrs
removed; unmachined internal surfaces of cast
housings must be free of core grit. The dimensional
and form accuracy of all components in contact with Figure 1
the bearings must be checked. The bearings will only
If a non-separable bearing is to be pressed onto the
perform satisfactorily if the prescribed tolerances of
shaft and into the housing simultaneously, the tool set
the mounting structures are adhered to. The bearings
shown by Figure 2, in which a mounting ring is
should be left in their original packages until
inserted between the dolly and the bearing to
immediately before mounting.
simultaneously abut the side faces of the inner and
There is usually no need to remove preservative outer rings, may be used. For the mounting forces to
protecting the bearings. If, however, the bearings are be applied equally to both rings, the abutment
to be grease-lubricated and used at very high or very surfaces of the mounting ring must lie in the same
low temperatures, or when the grease has been plane.
determined to be incompatible with the preservative, it
is necessary to wash the bearings in a suitable, non-
contaminated fluid and carefully dry the bearings prior
to mounting. This is to prevent any detrimental effect
on the lubricating properties of the grease.
Figure 2
329
Installation Procedures MRC Bearing Services
330
Installation Procedures
Since there is a definite relationship between radial The claws of the puller should be placed against the
and axial internal clearance of angular contact ball side face of the ring to be removed or an adjacent
bearings, it is sufficient to specify a single value, component; e.g., a labyrinth ring, etc. Dismounting is
generally the axial internal clearance. This specified made easier if, when designing the bearing
value is then obtained, starting from a condition of arrangement, slots are provided in the shaft and
zero clearance, by loosening or tightening a nut on housing shoulders to accommodate the claws of the
the shaft or a threaded ring in the housing bore, or by puller. Outer rings can be removed more easily from
inserting calibrated shims between one of the bearing their housings if tapped holes are provided in the
rings and its abutment. The actual methods used to shoulders to take withdrawal screws (Figure 6).
adjust the clearance and measure the set clearance
are determined by whether a few or many bearings
are to be mounted.
Dismounting of Bearings
If bearings are to be reused after removal from the
application, the force used to dismount them must
never be applied through the rolling elements. With
separable bearings, the ring with the rolling element
and cage assembly can be removed independently of
the other ring. With non-separable bearings, the ring
having the looser fit should be removed from its
seating first. To dismount a bearing ring having an
interference fit, the tools and accessories described in Figure 6
the following may be used depending on bearing type
and size.
Bearing Ring Puller
Small bearings may be removed from their seatings
by using a puller as illustrated in Figure 5.
Figure 5
331
Installation Procedures MRC Bearing Services
332
Installation Procedures
333
Installation Procedures MRC Bearing Services
334
Installation Procedures
335
Shaft and Housing Shoulder Diameters MRC Bearing Services
Shoulder Diameters for Millimeter
and Inch-size MRC Ball Bearings The tables on these pages show minimum shaft
shoulder diameters and maximum housing shoulder
diameters as established by the MRC Technical
Services Department. However, the user may wish to
modify these diameters to meet specific requirements
such as assembly or disassembly problems or
extremely heavy thrust loads. Please consult the
MRC Technical Services Department for specific
recommendations concerning your requirements.
34 5.51 .22 14.2 .56 132 172.0 6.77 238.0 9.37 148K 254.0 10.00 346.0 13.62
35 6.61 .26 17.0 .67 134 182.0 7.17 253.0 9.96 152K 278.0 10.95 382.0 15.04
36 7.61 .30 17.0 .67 136 192.0 7.56 266.0 10.55 156K 298.0 11.73 402.0 15.83
37 8.61 .34 20.0 .79 138 202.0 7.95 288.0 11.34 160K 318.0 12.52 442.0 17.40
38 9.71 .38 20.0 .79 140 212.0 8.35 308.0 12.13 164K 338.0 13.31 462.0 18.19
39 11.4 .45 23.4 .92 142 222.0 8.74 326.0 12.84
200 12.7 .50 24.9 .98
R2 4.6 .179 8.3 .33 144 234.0 9.21 336.0 13.23 201 14.7 .58 26.9 1.06
R2A 4.6 .179 11.8 .47 146 244.0 9.61 356.0 14.02 202 17.5 .69 30.0 1.18
R3 6.2 .24 11.8 .47 148 254.0 10.00 372.0 14.65
203 19.6 .77 34.0 1.34
R4 7.9 .31 14.4 .57 150 266.0 10.47 392.0 15.43 204 23.9 .94 40.9 1.61
R4A 8.2 .32 17.2 .68 152 278.0 10.95 412.0 16.22 205 29.0 1.14 46.0 1.81
R6 11.5 .45 20.3 .80 156 298.0 11.73 442.0 17.40
206 34.0 1.34 56.1 2.21
R8 15.9 .63 26.0 1.03 164 338.0 13.31 482.0 18.98 207 38.9 1.53 65.0 2.56
R10 19.1 .75 31.8 1.25 100K 11.9 .47 24.1 .95 208 43.9 1.73 72.9 2.87
R12 22.2 .88 38.1 1.50 101K 14.0 .55 25.9 1.02
102K 17.0 .67 30.0 1.18 209 49.3 1.94 78.0 3.07
R14 25.4 1.00 44.5 1.75 210 54.1 2.13 83.1 3.27
R16 28.6 1.13 47.6 1.88 103K 19.1 .75 33.0 1.30 211 61.2 2.41 93.5 3.68
R18 31.8 1.25 50.8 2.00 104K 22.6 .89 37.1 1.46
105K 27.4 1.08 41.9 1.65 212 67.8 2.67 101.0 3.98
R20 34.9 1.38 54.0 2.13 213 72.6 2.86 111.0 4.37
R22 38.1 1.50 60.3 2.38 106K 34.0 1.34 49.0 1.93 214 77.7 3.06 116.0 4.57
R24 41.3 1.63 63.5 2.50 107K 38.9 1.53 56.1 2.21
108K 43.9 1.73 62.0 2.44 215 82.6 3.25 121.0 4.76
102 17.0 .67 30.0 1.18 216 90.2 3.55 130.0 5.12
103 19.1 .75 35.1 1.38 109K 49.3 1.94 69.0 2.72 217 95.3 3.75 140.0 5.51
104 22.6 .89 37.1 1.46 110K 54.1 2.13 73.9 2.91
111K 59.2 2.33 83.1 3.27 218 100.0 3.94 150.0 5.91
105 27.4 1.08 46.7 1.84 219 107.0 4.21 158.0 6.22
106 34.0 1.34 56.1 2.21 112K 64.3 2.53 88.1 3.47 220 112.0 4.41 168.0 6.61
107 38.9 1.53 64.0 2.52 113K 69.1 2.72 92.9 3.66
114K 73.9 2.91 103.0 4.06 221 117.0 4.61 178.0 7.01
108 43.9 1.73 73.9 2.91 222 122.0 4.80 188.0 7.40
109 49.3 1.94 79.0 3.11 115K 79.0 3.11 108.0 4.25 224 132.0 5.20 203.0 7.99
110 54.1 2.13 83.1 3.27 116K 84.1 3.31 118.0 4.65
117K 88.9 3.50 123.0 4.84 226 144.0 5.67 216.0 8.50
111 59.2 2.33 92.9 3.66 228 154.0 6.05 236.0 9.29
112 64.3 2.53 98.0 3.86 118K 97.5 3.84 131.0 5.16 230 164.0 6.46 256.0 10.08
113 69.1 2.72 108.0 4.25 119K 102.0 4.05 136.0 5.35
120K 107.0 4.23 141.0 5.55 232 174.0 6.85 276.0 10.87
114 73.9 2.91 113.0 4.45 234 188.0 7.40 292.0 11.50
115 79.0 3.11 123.0 4.84 121K 115.0 4.53 150.0 5.91 236 198.0 7.80 302.0 11.89
116 84.1 3.31 128.0 5.05 122K 120.0 4.72 160.0 6.30
124K 130.0 5.12 170.0 6.69 238 208.0 8.19 322.0 12.68
117 88.9 3.50 136.0 5.35 240 218.0 8.58 342.0 13.47
118 97.5 3.84 141.0 5.55 126K 140.0 5.51 190.0 7.48 242 232.0 9.13 359.0 14.13
119 102.0 4.05 150.0 5.91 128K 150.0 5.91 200.0 7.87
130K 162.0 6.38 213.0 8.39 244 238.0 9.37 382.0 15.04
120 107.0 4.23 150.0 5.91 246 254.0 10.00 397.0 15.63
122 120.0 4.72 165.0 6.49 132K 172.0 6.77 228.0 8.98 248 258.0 10.16 422.0 16.61
124 130.0 5.12 180.0 7.09 134K 182.0 7.17 248.0 9.76
136K 192.0 7.56 266.0 10.55 250 277.0 10.92 434.0 17.07
126 140.0 5.51 195.0 7.68 252 282.0 11.10 458.0 18.03
128 150.0 5.91 208.0 8.19 138K 202.0 7.95 278.0 10.95 256 302.0 11.89 478.0 18.82
130 162.0 6.38 223.0 8.78 140K 212.0 8.35 298.0 11.73
144K 234.0 9.21 326.0 12.84 260 322.0 12.68 518.0 20.39
264 342.0 13.47 558.0 21.97
336
Shaft and Housing Shoulder Diameters
Shoulder Diameters for Millimeter
and Inch-size MRC Ball Bearings
300 12.7 .50 30 1.18 418 108.0 4.25 207.0 8.15 1900 11.2 .44 20.8 .82
301 16.0 .63 31 1.22 419 109.0 4.30 231.0 9.10 1901 13.2 .52 22.9 .90
302 19.1 .75 36.1 1.42 420 121.0 4.75 245.0 9.64 1902 16.3 .64 26.9 1.06
303 21.1 .83 40.9 1.61 421 130.0 5.10 267.0 10.52 1903 18.0 .71 29.0 1.14
304 23.9 .94 45.0 1.77 422 138.0 5.42 294.0 11.57 1904 21.6 .85 35.3 1.39
305 29.0 1.14 55.1 2.17 1905 26.7 1.05 39.9 1.57
1800 12.0 .47 17.0 .67
306 34.0 1.34 65.0 2.56 1801 14.0 .55 19.0 .75 1906 31.8 1.25 45.5 1.79
307 42.9 1.69 71.1 2.80 1802 17.0 .67 22.0 .87 1907 37.1 1.46 52.8 2.08
308 49.0 1.93 81.0 3.19 1908 42.7 1.68 59.4 2.34
1803 19.0 .75 24.0 .95
309 54.1 2.13 90.9 3.58 1804 22.0 .87 30.0 1.18 1909 47.8 1.88 65.3 2.57
310 59.9 2.36 100.0 3.94 1805 27.0 1.06 35.0 1.38 1910 52.3 2.06 69.6 2.74
311 65.0 2.56 110.0 4.33 1911 58.2 2.29 76.7 3.02
1806 32.0 1.26 40.0 1.58
312 72.1 2.84 118.0 4.65 1807 37.0 1.46 45.0 1.77 1912 63.2 2.49 81.8 3.22
313 77.0 3.03 128.0 5.04 1808 42.0 1.65 50.0 1.97 1913 68.1 2.68 86.9 3.42
314 82.0 3.23 138.0 5.43 1914 73.9 2.91 96.0 3.78
1809 47.0 1.85 56.0 2.21
315 87.1 3.43 148.0 5.83 1810 52.0 2.05 63.0 2.48 1915 78.5 3.09 101.0 3.99
316 91.9 3.62 158.0 6.22 1811 57.0 2.24 70.0 2.76 1916 83.8 3.30 106.0 4.18
317 99.1 3.90 166.0 6.54 1917 89.4 3.52 116.0 4.56
1812 62.0 2.44 76.0 2.99
318 104.0 4.09 176.0 6.93 1813 69.0 2.72 81.0 3.19 1918 94.2 3.71 121.0 4.75
319 109.0 4.29 186.0 7.32 1814 74.0 2.91 86.0 3.39 1919 99.8 3.93 125.0 4.93
320 114.0 4.49 201.0 7.91 1920 105.0 4.13 135.0 5.33
1815 79.0 3.11 91.0 3.58
321 119.0 4.69 211.0 8.31 1816 84.0 3.31 96.0 3.78 1921 110.0 4.33 140.0 5.51
322 124.0 4.88 226.0 8.90 1817 90.0 3.54 105.0 4.13 1922 115.0 4.52 145.0 5.70
324 134.0 5.28 246.0 9.69 1924 125.0 4.93 160.0 6.28
1818 95.0 3.74 110.0 4.33
326 148.0 5.83 262.0 10.32 1819 100.0 3.94 115.0 4.53 1926 136.0 5.36 174.0 6.85
328 158.0 6.22 282.0 11.10 1820 105.0 4.13 120.0 4.72 1928 146.0 5.76 184.0 7.24
330 168.0 6.61 302.0 11.89 1930 158.0 6.21 202.0 7.97
1821 110.0 4.33 125.0 4.92
332 178.0 7.01 322.0 12.68 1822 115.0 4.53 135.0 5.32 1932 168.0 6.62 212.0 8.33
334 188.0 7.40 342.0 13.47 1824 125.0 4.92 145.0 5.71 1934 178.0 7.01 222.0 8.74
336 198.0 7.80 362.0 14.25 1936 189.0 7.44 241.0 9.50
1826 136.5 5.37 158.5 6.24
338 212.0 8.35 378.0 14.88 1828 146.5 5.77 168.5 6.63 1938 199.0 7.83 251.0 9.89
340 222.0 8.74 398.0 15.67 1830 156.5 6.16 183.5 7.22 1940 210.0 8.27 269.0 10.61
342 240.0 9.43 412.0 16.21 1944 231.0 9.09 289.0 11.38
1832 166.5 6.56 193.5 7.62
344 242.0 9.53 438.0 17.24 1834 176.5 6.95 208.5 8.21 1948 251.0 9.88 309.0 12.17
348 262.0 10.32 478.0 18.82 1836 186.5 7.34 218.5 8.61 1952 271.0 10.67 349.0 13.74
352 288.0 11.34 512.0 20.16 1956 291.0 11.46 369.0 14.53
1838 198.0 7.80 232.0 9.13
356 308.0 12.13 552.0 21.73 1840 208.0 8.19 242.0 9.53 1960 313.0 12.32 407.0 16.02
403 24.1 .95 55.1 2.17 1844 228.0 8.98 262.0 10.32 1964 333.0 13.11 427.0 16.81
404 26.9 1.06 65.0 2.56 1968 353.0 13.90 447.0 17.60
405 34.0 1.34 71.1 2.80 1848 249.0 9.81 291.0 11.46
1852 269.0 10.59 311.0 12.24 1972 373.0 14.69 467.0 18.39
406 39.1 1.54 81.0 3.19 1856 289.0 11.38 341.0 13.43 1976 396.0 15.59 504.0 19.84
407 43.9 1.73 90.9 3.58 1980 416.0 16.38 524.0 20.63
408 50.0 1.97 100.0 3.94 1860 311.0 12.24 369.0 14.53
1864 331.0 13.03 389.0 15.32 1984 436.0 17.17 544.0 21.42
409 55.1 2.17 110.0 4.33 1868 351.0 13.82 409.0 16.10 1988 456.0 17.95 584.0 22.99
410 62.0 2.44 118.0 4.65 1992 476.0 18.74 604.0 23.78
411 67.1 2.64 128.0 5.04 1872 371.0 14.61 429.0 16.89
1876 391.0 15.39 469.0 18.47 XLS1³|₈ 39.7 1.56 60.3 2.38
412 72.1 2.84 138.0 5.43 1880 411.0 16.18 489.0 19.25 XLS1¹|₂ 49.2 1.69 63.5 2.50
413 77.0 3.03 148.0 5.83 XLS1⁵|₈ 46.0 1.81 68.3 2.69
414 84.1 3.31 166.0 6.54 1884 431.0 16.97 509.0 20.04
1888 451.0 17.76 529.0 20.83 XLS1³|₄ 49.2 1.94 71.4 2.81
415 88.9 3.50 176.0 6.93 1892 473.0 18.62 567.0 22.32 XLS1⁷|₈ 52.4 2.06 76.2 3.00
416 94.0 3.70 186.0 7.32 XLS2 55.6 2.19 79.4 3.13
417 103.0 4.06 192.0 7.56 1896 493.0 19.41 587.0 23.11 XLS2¹|₈ 60.3 2.38 81.0 3.19
337
Shaft and Housing Shoulder Diameters MRC Bearing Services
Shoulder Diameters for Millimeter
and Inch-size MRC Ball Bearings
S H S H S H
MRC MRC MRC
Bearing Min. Max. Bearing Min. Max. Bearing Min. Max.
Number mm in mm in Number mm in mm in Number mm in mm in
XLS2¹|₄ 63.5 2.50 84.1 3.31 108 10.0 .39 20.0 .79 1409 54.0 2.13 111.0 4.37
XLS2³|₈ 66.7 2.63 88.9 3.50 129 13.0 .51 22.0 .87 1410 61.0 2.40 119.0 4.69
XLS2¹|₂ 69.9 2.75 92.1 3.63 1411 66.0 2.60 129.0 5.08
1200E 14.0 .55 26.0 1.02
XLS2⁵|₈ 73.0 2.88 98.4 3.88 1201E 16.0 .63 28.0 1.10 1412 71.0 2.80 139.0 5.47
XLS2³|₄ 76.2 3.00 98.4 3.88 1202E 19.0 .75 31.0 1.22 2200E 14.0 .55 26.0 1.02
XLS2⁷|₈ 81.0 3.19 106.0 4.19 2201E 16.0 .63 28.0 1.10
1203E 21.0 .83 36.0 1.42 2202E 19.0 .75 31.0 1.22
XLS3 84.1 3.31 106.0 4.19 1204E 25.0 .98 42.0 1.65
XLS3¹|₈ 87.3 3.44 113.0 4.44 1205E 30.0 1.18 47.0 1.85 2203E 21.0 .83 36.0 1.41
XLS3¹|₄ 90.5 3.56 113.0 4.44 2204E 25.0 .98 42.0 1.65
1206E 35.0 1.38 57.0 2.24 2205E 30.0 1.18 47.0 1.85
XLS3³|₈ 93.7 3.69 119.0 4.69 1207E 41.5 1.63 65.5 2.58
XLS3¹|₂ 96.8 3.81 119.0 4.69 1208E 46.5 1.83 73.5 2.89 2206E 35.0 1.38 57.0 2.24
XLS3⁵|₈ 100.0 3.94 122.0 4.81 2207E 41.5 1.63 65.5 2.58
1209E 51.5 2.03 78.5 3.09 2208E 46.5 1.83 73.5 2.89
XLS3³|₄ 103.0 4.06 122.0 4.81 1210E 56.5 2.22 83.5 3.29
XLS3⁷|₈ 106.0 4.19 135.0 5.31 1211E 63.0 2.48 95.0 3.74 2209E 51.5 2.03 78.5 3.09
XLS4 110.0 4.31 135.0 5.31 2210E 56.5 2.22 83.5 3.29
1212E 68.0 2.68 102.0 4.02 2211E 63.0 2.48 92.0 3.62
XLS4¹|₈ 113.0 4.44 144.0 5.69 1213E 73.0 2.87 112.0 4.41
XLS4¹|₄ 116.0 4.56 144.0 5.69 1214 78.0 3.07 117.0 4.61 2212E 68.0 2.68 102.0 4.02
XLS4³|₈ 119.0 4.69 151.0 5.94 2213E 73.0 2.87 112.0 4.41
1215 83.0 3.27 122.0 4.80 2214 78.0 3.07 117.0 4.61
XLS4¹|₂ 122.0 4.81 151.0 5.94 1216 89.0 3.51 131.0 5.16
XLS4⁵|₈ 125.0 4.94 157.0 6.19 1217 94.0 3.70 141.0 5.55 2215 83.0 3.27 122.0 4.81
XLS4³|₄ 129.0 5.06 157.0 6.19 2216E 89.0 3.50 131.0 5.16
1218 99.0 3.90 151.0 5.95 2217 94.0 3.70 141.0 5.55
XLS4⁷|₈ 132.0 5.19 170.0 6.69 1219 106.0 4.17 159.0 6.26
XLS5 135.0 5.31 170.0 6.69 1220 111.0 4.37 169.0 6.65 2218 99.0 3.90 151.0 5.95
XLS5¹|₈ 140.0 5.50 175.0 6.88 2219 106.0 4.17 159.0 6.26
1221 116.0 4.57 178.0 7.05 2220 111.0 4.37 169.0 6.65
XLS5¹|₄ 143.0 5.63 175.0 6.88 1222 121.0 4.76 189.0 7.44
XLS5³|₈ 146.0 5.75 181.0 7.13 1224 131.0 5.16 204.0 8.03 2221 116.0 4.57 179.0 7.05
XLS5¹|₂ 149.0 5.88 181.0 7.13 1226 143.0 5.63 217.0 8.54 2222 121.0 4.76 189.0 7.44
XLS5⁵|₈ 152.0 6.00 187.0 7.38 1301E 17.0 .67 32.0 1.26 2301 17.0 .67 32.0 1.26
XLS5³|₄ 156.0 6.13 187.0 7.38 1302E 20.0 .79 37.0 1.46 2302 20.0 .79 37.0 1.46
XLS5⁷|₈ 159.0 6.25 194.0 7.63 1303E 22.0 .87 42.0 1.65 2303 22.0 .87 42.0 1.65
XLS6 162.0 6.38 194.0 7.63 1304E 26.5 1.04 45.5 1.79 2304 26.5 1.04 45.5 1.79
XLS6¹|₄ 168.0 6.63 206.0 8.13 1305E 31.5 1.24 55.5 2.19 2305 31.5 1.24 55.5 2.19
XLS6¹|₂ 175.0 6.88 213.0 8.38 1306E 36.5 1.44 65.5 2.58 2306 36.5 1.44 65.5 2.58
XLS6³|₄ 184.0 7.25 216.0 8.50 1307E 43.0 1.69 72.0 2.84 2307E 43.0 1.69 72.0 2.84
XLS7 191.0 7.50 229.0 9.00 1308E 48.0 1.89 82.0 3.23 2308E 48.0 1.89 82.0 3.23
XLS7¹|₄ 197.0 7.75 235.0 9.25 1309E 53.0 2.09 92.0 3.62 2309E 53.0 2.09 92.0 3.62
XLS7¹|₂ 203.0 8.00 241.0 9.50 1310E 59.0 2.32 101.0 3.98 2310 59.0 2.32 101.0 3.98
XLS7³|₄ 210.0 8.25 254.0 10.00 1311E 64.0 2.52 111.0 4.37 2311 64.0 2.52 111.0 4.37
XLS8 216.0 8.50 260.0 10.25 1312E 71.0 2.80 119.0 4.69 2312 71.0 2.80 119.0 4.69
XLS8¹|₄ 222.0 8.75 267.0 10.50 1313E 76.0 2.99 129.0 5.08 2313 76.0 2.99 129.0 5.08
XLS8¹|₂ 229.0 9.00 279.0 11.00 1314 81.0 3.19 139.0 5.47 2314 81.0 3.19 139.0 5.47
XLS8³|₄ 235.0 9.25 286.0 11.25 1315 86.0 3.39 149.0 5.87 2315 86.0 3.39 149.0 5.87
XLS9 241.0 9.50 292.0 11.50 1316 91.0 3.58 159.0 6.26 2316 91.0 3.58 159.0 6.26
XLS9¹|₂ 257.0 10.13 308.0 12.13 1317 98.0 3.86 167.0 6.58 2317 98.0 3.86 167.0 6.58
XLS10 270.0 10.63 321.0 12.63 1318 103.0 4.06 177.0 6.97 2318 103.0 4.06 177.0 6.97
XLS10¹|₂ 283.0 11.13 340.0 13.38 1319 108.0 4.25 187.0 7.36 2319 108.0 4.25 187.0 7.36
XLS11 295.0 11.63 352.0 13.88 1320 113.0 4.45 202.0 7.95 2320 113.0 4.45 202.0 7.95
XLS11¹|₂ 308.0 12.13 371.0 14.63 1322 123.0 4.84 227.0 8.94 2322 123.0 4.84 227.0 8.94
XLS12 321.0 12.63 391.0 15.38 1406 38.0 1.50 82.0 3.23 11204E — — 42.0 1.65
1407 43.0 1.69 92.0 3.62 11205E — — 47.0 1.85
135 7.0 .28 17.0 .67 1408 49.0 1.93 101.0 3.98 11206E — — 57.0 2.24
126 8.0 .32 17.0 .67
127 9.0 .35 20.0 .79
338
Shaft and Housing Shoulder Diameters
Shoulder Diameters for Millimeter
and Inch-size MRC Ball Bearings
11210E — — 83.5 3.29 1207EK 47.0 1.85 38.0 1.50 65.5 2.58 2308EK 53.0 2.09 45.0 1.77 82.0 3.23
11212E — — 102.5 4.02 1208EK 53.0 2.09 43.0 1.69 73.5 2.89 2309EK 60.0 2.36 50.0 1.97 92.0 3.62
1209EK 57.0 2.24 48.0 1.89 78.5 3.09 2310K 65.0 2.56 56.0 2.21 101.0 3.98
11305E — — 55.5 2.19 1210EK 62.0 2.44 53.0 2.09 83.5 3.29 2311K 72.0 2.84 61.0 2.40 111.0 4.37
11306E — — 65.5 2.58 1211EK 70.0 2.76 60.0 2.36 95.0 3.74 2312K 76.0 2.99 66.0 2.60 119.0 4.69
11307E — — 72.0 2.84 1212EK 78.0 3.07 64.0 2.52 102.0 4.02 2313K 85.0 3.35 72.0 2.84 129.0 5.08
11308E — — 82.0 3.23 1213K 85.0 3.35 70.0 2.76 112.0 4.41 2315K 97.0 3.82 82.0 3.23 149.0 5.87
11310E — — 101.0 3.98 1215K 93.0 3.66 80.0 3.15 122.0 4.81 2316K 104.0 4.09 88.0 3.47 159.0 6.26
1216K 101.0 3.98 85.0 3.35 131.0 5.16 2317K 111.0 4.37 94.0 3.70 167.0 6.58
Ball Screw Supports 1217K 107.0 4.21 90.0 3.54 141.0 5.55 2318K 115.0 4.53 100.0 3.94 177.0 6.97
1218K 112.0 4.41 95.0 3.74 151.0 5.95 2319K 121.0 4.76 105.0 4.13 187.0 7.36
J078DF 27.3 1.07 41.7 1.64 1219K 120.0 4.72 100.0 3.94 159.0 6.26 2320K 130.0 5.12 110.0 4.33 202.0 7.95
J093DF 33.3 1.31 55.3 2.18
J098DF 36.3 1.43 55.3 2.18 1220K 127.0 5.00 106.0 4.17 169.0 6.65 2322K 145.0 5.71 121.0 4.76 227.0 8.94
1221K 134.0 5.28 111.0 4.37 179.0 7.05
J150DF 47.1 1.86 63.0 2.48 1222K 140.0 5.51 116.0 4.57 189.0 7.44
J175DF 52.0 2.05 67.9 2.67
J225DF 65.2 2.57 81.2 3.20 1224K 150.0 5.91 127.0 5.00 204.0 8.03
J300DF 85.6 3.37 102.0 4.00 1304EK 33.0 1.30 23.0 .91 45.5 1.79
J400DF 112.0 4.41 135.0 5.30 1305EK 37.0 1.46 28.0 1.10 55.5 2.19
1306EK 44.0 1.73 33.0 1.30 65.5 2.58
339
Approximate Weights
of MRC Ball Bearings MRC Bearing Services
The weights shown below are approximate for shipping purposes. For exact weights consult our Technical
Services Department.
Basic Wt. Basic Wt. Basic Wt. Basic Wt. Basic Wt. Basic Wt.
Brg. in Brg. in Brg. in Brg. in Brg. in Brg. in
No. Lbs. No. Lbs. No. Lbs. No. Lbs. No. Lbs. No. Lbs.
R-2 Series Excello Bearings XO-90 2.40 209 .97 417 18. 5320 32.
Small Inch Size XO-20 .16 XO-115 6.00 210 1.1 418 23. 5321 37.
R-2 .003 XO-30 .26 XO-135 1.06 211 1.4 419 32. 5322 45.
R-2-A .007 XO-54 .53 XO-155 5.00 212 1.8 420 38.
R-3 .005 XO-55 .53 XO-165 12.00 213 2.4 421 49. 5400 Series
R-4 .010 XO-57 .66 214 2.6 422 62. 5403 1.1
R-4A .018 XO-67 .84 30 Series 215 2.8 5404 1.7
R-61) .022 Extra Small Size 216 3.4 1900-S, R 5405 2.1
R-81) .042 34 .02 217 4.3 1900 .02 5406 2.8
R-101) .069 35 .02 218 5.2 1901 .03 5407 3.6
R-123) .105 36 .02 219 6.4 1902 .04 5408 5.0
R-142) .169 37 .03 220 7.6 1903 .04 5409 6.6
R-162) .180 38 .03 221 9.0 1904 .09 5410 8.5
R-182) .200 39 .05 222 10.6 1905 .10 5411 10.
R-202) .212 224 13.5 1906 .12 5412 12.
226 15.5 1907 .18 5413 15.
R-242) .331 100-KS, -KR 228 19.
100 .04 1908 .27 5414 21.
XLS Series 230 25. 1909 .31 5415 23.
101 .05 232 30.
1³|₈ .44 102 .07 1910 .32 5416 26.
234 38. 1911 .44 5417 30.
1¹|₂ .47 103 .09 236 39.
104 .16 1912 .47 5418 40.
1⁵|₈ .53 238 47. 1913 .50 5419 65.
105 .19 240 56.
1³|₄ .57 106 .28 1914 .82 5420 75.
242 66. 1915 .86
1⁷|₈ .70 107 .37 244 79.
2 .73 108 .45 1916 .91 Self-Aligning
246 85. 1917 1.3
2¹|₈ .78 109 .58 248 106. 100, 1200 Series
110 .62 1918 1.4 135 .020
2¹|₄ .81 250 123. 1919 1.5
111 .91 252 141. 126 .020
2³|₈ .99 112 .98 1920 1.9 127 .031
256 148. 1921 2.0
2¹|₂ 1.0 113 1.0 260 185. 108 .031
114 1.4 1922 2.1 129 .049
2⁵|₈ 1.2 264 226. 1924 2.8
2³|₄ 1.1 115 1.5 1200 .075
116 2.0 1926 3.7 1201 .088
2⁷|₈ 1.5 117 2.1
300-S, -M, -R 1928 4.0 1202 .11
3 1.4 118 2.8 300 .13 1930 6.0 1203 .16
3¹|₈ 1.7 119 2.9 301 .14 1932 6.4 1204 .26
120 3.0 302 .19 1934 6.7 1205 .31
3¹|₄ 1.6 303 .26 1936 9.9
3³|₈ 1.8 121 3.8 1206 .49
122 4.7 304 .33 1938 10.4 1207 .71
3¹|₂ 1.7 124 5.0 305 .51 1940 14.6 1208 .93
3⁵|₈ 1.9 126 7.6 306 .78 1209 1.05
3³|₄ 1.8 128 8.1 307 1.0 5200 Series 1210 1.15
130 9.8 308 1.5 5200 .11 1211 1.55
3⁷|₈ 2.5 309 2.0 5201 .13
4 2.4 132 12.2 1212 2.00
134 16.3 310 2.6 5202 .15 1213 2.55
4¹|₈ 2.9 136 21. 311 3.2 5203 .23 1214 2.75
4¹|₄ 2.7 138 22. 312 4.0 5204 .36 1215 3.00
140 29. 313 5.0 5205 .54 1216 3.65
4³|₈ 3.0 314 6.0
144 38. 5206 .76 1217 4.50
4¹|₂ 2.9 315 7.4 5207 1.2
148 40. 1218 5.50
4⁵|₈ 3.2 152 60. 316 8.8 5208 1.6 1219 6.85
4³|₄ 3.0 156 64. 317 10.4 5209 1.7 1220 8.15
160 90. 318 12.1 5210 1.8 1221 9.60
4⁷|₈ 4.4 319 14.
5 4.2 164 95. 5211 2.5 1222 11.5
320 17. 5212 3.3 1224 15.0
5¹|₈ 4.6 321 20. 5213 4.3
5¹|₄ 4.3 120-R Series 322 23.
1226 18.5
120 4.8 5214 4.7
5³|₈ 4.7 324 32. 5215 5.5
122 6.0 326 38. 1300 Series
5¹|₂ 4.5 124 7.5 5216 6.6 1301 .15
328 47. 5217 8.2
5⁵|₈ 4.9 126 9.3 330 56. 1302 .21
128 11.3 5218 10.3 1303 .29
5³|₄ 4.7 332 66. 5219 11.6
130 13.5 334 78. 1304 .35
5⁷|₈ 5.1 132 16.0 5220 14.1 1305 .57
6 4.9 336 91. 5221 17.
134 18.8 338 105. 1306 .86
6¹|₄ 6.5 136 22.0 5222 20. 1307 1.10
340 118.
6¹|₂ 6.7 138 26.8 342 146. 1308 1.60
6³|₄ 6.9 140 32.5 5300 Series 1309 2.10
344 155. 5300 .21
7 9.0 142 39.0 348 198. 1310 2.65
144 41.0 5301 .23 1311 3.55
7¹|₄ 9.2 352 247. 5302 .29
146 48.5 356 302. 1312 4.30
7¹|₂ 9.5 148 56.5 5303 .43 1313 5.40
7³|₄ 12.0 150 61.4 5304 .52 1314 6.60
8 12.3 152 75.0
400-S, -M, 5305 .86 1315 7.85
156 91.0 403 .57 5306 1.3 1316 9.25
8¹|₄ 13.6 404 .93
164 113.0 5307 1.9 1317 11.00
8¹|₂ 15.6 405 1.2 5308 2.5 1318 13.0
8³|₄ 16.0 406 1.7 5309 3.3
9 16.4
200-S, -M, -R 407 2.2
1319 15.0
200 .07 5310 4.4 1320 18.5
9¹|₂ 20.5 408 2.9 5311 5.8 1322 26.5
201 .08 409 3.7
10 21.3 202 .11 5312 7.3
410 4.5 5313 9.3
10¹|₂ 26.1 203 .15 411 5.5 1400 Series
11 27.1 204 .24 5314 11.3 1406 2.20
412 6.7 5315 14.2
11¹|₂ 32.6 205 .31 413 8.1 1407 2.85
206 .50 5316 16. 1408 3.75
12 38.9 414 12. 5317 19.
207 .69 415 14. 1409 4.75
XO Series 208 .88 5318 22. 1410 5.85
416 16. 5319 26.
1)
Add 25% for shielded or sealed type.
2)
Add 33% for shielded or sealed type.
3) Add 40% for shielded or sealed type.
340
Approximate Weights
of MRC Ball Bearings
The weights shown below are approximate for shipping purposes. For exact weights consult our Technical
Engineering Department.
Basic Wt. Basic Wt. Basic Wt. Basic Wt. Basic Wt. Basic Wt.
Brg. in Brg. in Brg. in Brg. in Brg. in Brg. in
No. Lbs. No. Lbs. No. Lbs. No. Lbs. No. Lbs. No. Lbs.
1411 7.15 7117 2.1 7300, -P, -PJ 9200-U, UP Cartridge Type -SFFC, - 1814 .31
1412 8.70 7118 2.8 7300 .13 9202 .11 SZZC 1815 .33
7119 2.9 7301 .14 9203 .15 38 .04 1816 .40
2200 Series 7120 3.0 7302 .19 9204 .24 200 .10 1817 .60
2200 .10 7121 3.8 7303 .26 9205 .31 201 .13 1818 .62
2201 .12 7122 4.7 7304 .33 9206 .50 202 .16 1819 .66
2202 .13 7124 5.0 7305 .51 9207 .69 203 .22 1820 .68
2203 .19 7126 7.6 7306 .78 9208 .88 204 .35 1821 .71
2204 .31 7128 8.1 7307 1.0 9209 .97 205 .43 1822 1.3
2205 .35 7130 9.8 7308 1.5 9210 1.1 206 .56 1824 1.5
2206 .57 7132 12.2 7309 2.0 9211 1.4 207 .94 1826 2.1
2207 .88 7134 16.3 7310 2.6 9212 1.8 208 1.2 1828 2.2
2208 1.10 7136 21. 7311 3.2 9213 2.4 209 1.3 1830 3.1
2209 1.20 7138 22. 7312 4.0 9214 2.6 210 1.4 1832 3.2
2210 1.30 7140 29. 7313 5.0 9215 2.8 211 2.2 1834 4.2
2211 1.80 7144 38. 7314 6.0 9216 3.4 213 3.4 1836 4.4
2212 2.45 7148 40. 7315 7.4 9217 4.3 214 3.7 1838 5.8
2213 3.20 7152 60. 7316 8.8 9218 5.2 216 5.2 1840 6.0
2214 3.30 7156 64. 7317 10.4 9219 6.4 219 9.6 1844 6.6
2215 3.55 7160 90. 7318 12.1 9220 7.6 304 .47 1848 9.9
2216 4.40 7164 95. 7319 14. 9221 9.0 305 .72 1852 10.5
2217 5.50 7320 17. 9222 10.6 306 1.1 1856 16.5
2218 7.50 7120 Series 7321 20. 307 1.5 1860 23.0
2219 9.05 7120 4.8 7322 23. 9300-U, UP 308 2.0 1864 24.5
2220 11.0 7122 6.0 7324 32. 309 3.0 1868 25.5
9302 .19 1872 26.5
2221 13.5 7124 7.5 7326 38. 9303 .26 310 4.0
2222 15.5 7126 9.3 7328 47. 311 5.0 1876 44.0
9304 .33 1880 45.0
7128 11.3 7330 56. 9305 .51 312 6.0
2300 Series 7130 13.5 7332 66. 313 8.0 1884 47.5
9306 .78 1888 49.5
2301 .21 7132 16.0 7334 78. 9307 1.0 314 9.6
2302 .24 7134 18.8 7336 91. 315 12.2 1892 77.0
9308 1.5 1896 80.5
2303 .35 7136 22.0 7338 105. 9309 2.0 316 13.4
2304 .46 7138 26.8 7340 118. 9310 2.6 317 15.0
2305 .75 7140 32.5 7342 146. 9311 3.2 318 18.0 Ball Screw Supports
2306 1.10 7142 39.0 7344 155. 9312 4.0 320 22.5 J078DF .54
2307 1.50 7144 41.0 7348 198. 9313 5.0 J093DF .98
2308 2.05 7146 48.5 7352 247. 9314 6.0 100S Series J098DF .96
2309 2.75 7148 56.5 7356 302. 9315 7.4 102 .05 J150DF 1.1
2310 3.65 7150 61.4 9316 8.8 103 .08 J175DF 1.1
2311 4.65 7152 75.0 7400, P, PJ 9317 10.4 104 .12 J225DF 1.4
2312 5.75 7156 91.0 7403 .57 9318 12.1 105 .16 J300DF 1.9
2313 7.15 7164 113.0 7404 .93 9319 14. 106 .24 J400DF 4.5
2314 8.60 7405 1.2 9320 17. 107 .30 J078DFDT 1.1
2315 10.5 7200, -P, -PJ 7406 1.7 9321 20. 108 .39 J093DFDT 2.0
2316 13.5 7200 .07 7407 2.2 9322 23. 109 .45 J098DFDT 1.9
2317 15.5 7201 .08 7408 2.9 110 .48 J150DFDT 2.2
2318 18.5 7202 .11 7409 3.7 Adapter Type 111 .67 J175DFDT 2.3
2319 21.5 7203 .15 7410 4.5 J225DFDT 2.9
SX Series 112 .72
J300DFDT 3.8
2320 27.5 7204 .24 7411 5.5 205 .30 113 .89
2322 38.5 7205 .31 7412 6.7 114 1.1 J400DFDT 8.9
206 .47
7206 .50 7413 8.1 207 .69 115 1.4
11200 Series 7207 .69 7414 12. 116 1.6 Felt Seal Replacement
209 .88
11204 .40 7208 .88 7415 14. 210 .97 117 1.9 8008 .04
11205 .49 7209 .97 7416 16. 211 1.3 118 2.3 8013 .09
11206 .77 7210 1.1 7417 18. 213 2.4 119 2.7 8014 .12
11207 1.20 7211 1.4 7418 23. 215 2.8 8016 .10
11208 1.60 7212 1.8 7419 32. 216 3.1 100M Series 8026 .23
11209 1.70 7213 2.4 7420 38. 217 3.7 110M .57 8038 .04
11210 1.85 7214 2.6 7421 49. 218 4.8 113M 1.1 8500 .08
11212 3.30 7215 2.8 7422 62. 220 7.1 117M 2.3 8501 .10
7216 3.4 221 8.1 120M 4.2 8502 .11
11300 Series 7217 4.3 9100-UK 222 9.7 120MF 4.2 8503 .15
11305 .90 7218 5.2 9100 .04 305 .48 124M 6.7 8504 .23
11306 1.35 7219 6.4 9101 .05 306 .77 124MF 6.7 8505 .29
11307 1.80 7220 7.6 9102 .07 307 .97 126M 8.4 8506 .49
11308 2.45 7221 9.0 9103 .09 309 1.8 126MF 8.4 8507 .69
11310 3.75 7222 10.6 9104 .16 310 2.3 128M 10.1 8508 1.0
7224 13.5 9105 .19 311 2.9 128MF 10.1 8605 .51
7226 15.5 9106 .28 WC87008 .04
7100-KR 7228 19.
313 4.6 132M 14.2
WC87016 1.0
7100 .04 9107 .37 315 6.7 132MF 14.2
7230 25. 9108 .45 317 9.3 WC87500 .08
7101 .05 7232 30. WC87501 .10
7102 .07 9109 .58 318 10.9 1800S Series
7234 38. 9110 .62 320 15.6 WC87502 .11
7103 .09 7236 39. 1800 .012 WC87503 .15
7104 .16 9111 .91 321 18. 1801 .014
7238 47. 9112 .98 322 21. WC87504 .23
7105 .19 7240 56. 1802 .016 87007 .04
7106 .28 9113 1.0 1803 .018
7242 66. 9114 1.4 87008 .04
7107 .37 7244 79. Conveyor Roll 1804 .04 87013 .09
9115 1.5
7108 .45 7246 85. 9116 2.0 CONV- 1805 .05 87014 .12
7109 .58 7248 106. CONV-3-J .43 1806 .06 87016 .10
7110 .62 9117 2.1 1807 .07
7250 123. 9118 2.8 CONV-3-SF .37 87026 .23
7111 .91 7252 141. CONV-3-Y-2 .27 1808 .08 87036 .02
7112 .98 9119 2.9 1809 .09
7256 148. 9120 3.0 CONV-4-E-2 .91 87037 .04
7113 1.0 7260 185. CONV-4-J .33 1810 .11 87038 .04
7114 1.4 9121 3.8 1811 .18
7264 226. 9122 4.7 CONV-4-SF .55 87500 .08
7115 1.5 CONV-4-SZZ-2 .22 1812 .24 87501 .10
7116 2.0 CONV-504-3 .31 1813 .29 87502 .11
341
Millimeter—Inch Equivalents
(One inch = 25.4 millimeters) MRC Bearing Services
mm in mm in mm in mm in
1 0.0394 ¹|₃₂ + 56 2.2047 2⁷|₃₂ – 111 4.3701 4³|₈ – 166 6.5354 6¹⁷|₃₂ +
2 0.0787 ³|₃₂ – 57 2.2441 2¹|₄ – 112 4.4094 4¹³|₃₂ + 167 6.5748 6⁹|₁₆ +
3 0.1181 ¹|₈ – 58 2.2835 2⁹|₃₂ + 113 4.4488 4⁷|₁₆ + 168 6.6142 6⁵|₈ –
4 0.1575 ⁵|₃₂ + 59 2.3228 2⁵|₁₆ + 114 4.4882 4¹|₂ – 169 6.6535 6²¹|₃₂ –
5 0.1969 ³|₁₆ + 60 2.3622 2³|₈ – 115 4.5276 4¹⁷|₃₂ – 170 6.6929 6¹¹|₁₆ +
6 0.2362 ¹|₄ – 61 2.4016 2¹³|₃₂ – 116 4.5669 4⁹|₁₆ + 171 6.7323 6²³|₃₂ +
7 0.2756 ⁹|₃₂ – 62 2.4409 2⁷|₁₆ + 117 4.6063 4¹⁹|₃₂ + 172 6.7717 6²⁵|₃₂ –
8 0.3150 ⁵|₁₆ + 63 2.4803 2¹⁵|₃₂ + 118 4.6457 4²¹|₃₂ – 173 6.8110 6¹³|₁₆ –
9 0.3543 ¹¹|₃₂ + 64 2.5197 2¹⁷|₃₂ – 119 4.6850 4¹¹|₁₆ – 174 6.8504 6²⁷|₃₂ +
10 0.3937 ¹³|₃₂ – 65 2.5591 2⁹|₁₆ – 120 4.7244 4²³|₃₂ + 175 6.8898 6⁷|₈ +
11 0.4331 ⁷|₁₆ – 66 2.5984 2¹⁹|₃₂ + 121 4.7638 4³|₄ + 176 6.9291 6¹⁵|₁₆ –
12 0.4724 ¹⁵|₃₂ + 67 2.6378 2⁵|₈ + 122 4.8031 4¹³|₁₆ – 177 6.9685 6³¹|₃₂ –
13 0.5118 ¹|₂ + 68 2.6772 2¹¹|₁₆ – 123 4.8425 4²⁷|₃₂ – 178 7.0079 7 +
14 0.5512 ⁹|₁₆ – 69 2.7165 2²³|₃₂ – 124 4.8819 4⁷|₈ + 179 7.0472 7¹|₁₆ –
15 0.5906 ¹⁹|₃₂ – 70 2.7559 2³|₄ + 125 4.9213 4²⁹|₃₂ + 180 7.0866 7³|₃₂ –
16 0.6299 ⁵|₈ + 71 2.7953 2²⁵|₃₂ + 126 4.9606 4³¹|₃₂ – 181 7.1260 7¹|₈ +
17 0.6693 ²¹|₃₂ + 72 2.8346 2²⁷|₃₂ – 127 5.0000 5 182 7.1654 7⁵|₃₂ +
18 0.7087 ²³|₃₂ – 73 2.8740 2⁷|₈ – 128 5.0394 5¹|₃₂ + 183 7.2047 7⁷|₃₂ –
19 0.7480 ³|₄ – 74 2.9134 2²⁹|₃₂ + 129 5.0787 5³|₃₂ – 184 7.2441 7¹|₄ –
20 0.7874 ²⁵|₃₂ + 75 2.9528 2¹⁵|₁₆ + 130 5.1181 5¹|₈ – 185 7.2835 7⁹|₃₂ +
21 0.8268 ¹³|₁₆ + 76 2.9921 3 – 131 5.1575 5⁵|₃₂ + 186 7.3228 7⁵|₁₆ +
22 0.8661 ⁷|₈ – 77 3.0315 3¹|₃₂ + 132 5.1969 5³|₁₆ + 187 7.3622 7³|₈ –
23 0.9055 ²⁹|₃₂ – 78 3.0709 3¹|₁₆ + 133 5.2362 5¹|₄ – 188 7.4016 7¹³|₃₂ –
24 0.9449 ¹⁵|₁₆ + 79 3.1102 3¹|₈ – 134 5.2756 5⁹|₃₂ – 189 7.4409 7⁷|₁₆ +
25 0.9843 ³¹|₃₂ + 80 3.1496 3⁵|₃₂ – 135 5.3150 5⁵|₁₆ + 190 7.4803 7¹⁵|₃₂ +
26 1.0236 1¹|₃₂ – 81 3.1890 3³|₁₆ + 136 5.3543 5¹¹|₃₂ + 191 7.5197 7¹⁷|₃₂ –
27 1.0630 1¹|₁₆ + 82 3.2283 3⁷|₃₂ + 137 5.3937 5¹³|₃₂ – 192 7.5591 7⁹|₁₆ –
28 1.1024 1³|₃₂ + 83 3.2677 3⁹|₃₂ – 138 5.4331 5⁷|₁₆ – 193 7.5984 7¹⁹|₃₂ +
29 1.1417 1⁵|₃₂ – 84 3.3071 3⁵|₁₆ – 139 5.4724 5¹⁵|₃₂ + 194 7.6378 7⁵|₈ +
30 1.1811 1³|₁₆ – 85 3.3465 3¹¹|₃₂ + 140 5.5118 5¹|₂ + 195 7.6772 7¹¹|₁₆ –
31 1.2205 1⁷|₃₂ + 86 3.3858 3³|₈ + 141 5.5512 5⁹|₁₆ – 196 7.7165 7²³|₃₂ –
32 1.2598 1¹|₄ + 87 3.4252 3⁷|₁₆ – 142 5.5906 5¹⁹|₃₂ – 197 7.7559 7³|₄ +
33 1.2992 1⁵|₁₆ – 88 3.4646 3¹⁵|₃₂ – 143 5.6299 5⁵|₈ + 198 7.7953 7²⁵|₃₂ +
34 1.3386 1¹¹|₃₂ – 89 3.5039 3¹|₂ + 144 5.6693 5²¹|₃₂ + 199 7.8346 7²⁷|₃₂ –
35 1.3780 1³|₈ + 90 3.5433 3¹⁷|₃₂ + 145 5.7087 5²³|₃₂ – 200 7.8740 7⁷|₈ –
36 1.4173 1¹³|₃₂ + 91 3.5827 3¹⁹|₃₂ – 146 5.7480 5³|₄ – 201 7.9134 7²⁹|₃₂ +
37 1.4567 1¹⁵|₃₂ – 92 3.6220 3⁵|₈ – 147 5.7874 5²⁵|₃₂ + 202 7.9528 7¹⁵|₁₆ +
38 1.4961 1¹|₂ – 93 3.6614 3²¹|₃₂ + 148 5.8268 5¹³|₁₆ + 203 7.9921 8 –
39 1.5354 1¹⁷|₃₂ + 94 3.7008 3¹¹|₁₆ + 149 5.8661 5⁷|₈ – 204 8.0315 8¹|₃₂ +
40 1.5748 1⁹|₁₆ + 95 3.7402 3³|₄ – 150 5.9055 5²⁹|₃₂ – 205 8.0709 8¹|₁₆ +
41 1.6142 1⁵|₈ – 96 3.7795 3²⁵|₃₂ – 151 5.9449 5¹⁵|₁₆ + 206 8.1102 8¹|₈ –
42 1.6535 1²¹|₃₂ – 97 3.8189 3¹³|₁₆ + 152 5.9843 5³¹|₃₂ + 207 8.1496 8⁵|₃₂ –
43 1.6929 1¹¹|₁₆ + 98 3.8583 3²⁷|₃₂ + 153 6.0236 6¹|₃₂ – 208 8.1890 8³|₁₆ +
44 1.7323 1²³|₃₂ + 99 3.8976 3²⁹|₃₂ – 154 6.0630 6¹|₁₆ + 209 8.2283 8⁷|₃₂ +
45 1.7717 1²⁵|₃₂ – 100 3.9370 3¹⁵|₁₆ – 155 6.1024 6³|₃₂ + 210 8.2677 8⁹|₃₂ –
46 1.8110 1¹³|₁₆ – 101 3.9764 3³¹|₃₂ + 156 6.1417 6⁵|₃₂ – 211 8.3071 8⁵|₁₆ –
47 1.8504 1²⁷|₃₂ + 102 4.0157 4¹|₃₂ – 157 6.1811 6³|₁₆ – 212 8.3465 8¹¹|₃₂ +
48 1.8898 1⁷|₈ + 103 4.0551 4¹|₁₆ – 158 6.2205 6⁷|₃₂ + 213 8.3858 8³|₈ +
49 1.9291 1¹⁵|₁₆ – 104 4.0945 4³|₃₂ + 159 6.2598 6¹|₄ + 214 8.4252 8⁷|₁₆ –
50 1.9685 1³¹|₃₂ – 105 4.1339 4¹|₈ + 160 6.2992 6⁵|₁₆ – 215 8.4646 8¹⁵|₃₂ –
51 2.0079 2 + 106 4.1732 4³|₁₆ – 161 6.3386 6¹¹|₃₂ – 216 8.5039 8¹|₂ +
52 2.0472 2¹|₁₆ – 107 4.2126 4⁷|₃₂ – 162 6.3780 6³|₈ + 217 8.5433 8¹⁷|₃₂ +
53 2.0866 2³|₃₂ – 108 4.2520 4¹|₄ + 163 6.4173 6¹³|₃₂ + 218 8.5827 8¹⁹|₃₂ –
54 2.1260 2¹|₈ + 109 4.2913 4⁹|₃₂ + 164 6.4567 6¹⁵|₃₂ – 219 8.6220 8⁵|₈ –
55 2.1654 2⁵|₃₂ + 110 4.3307 4¹¹|₃₂ – 165 6.4961 6¹|₂ – 220 8.6614 8²¹|₃₂ +
342
Millimeter—Inch Equivalents
(One inch = 25.4 millimeters)
Note: The + or – sign indicates that the decimal equiva-
lent is larger or smaller than the fractional equivalent.
mm in mm in mm in mm in
221 8.7008 8¹¹|₁₆ + 276 10.8661 10⁷|₈ – 331 13.0315 13¹|₃₂ + 386 15.1969 15³|₁₆ +
222 8.7402 8³|₄ – 277 10.9055 10²⁹|₃₂ – 332 13.0709 13¹|₁₆ + 387 15.2362 15¹|₄ –
223 8.7795 8²⁵|₃₂ – 278 10.9449 10¹⁵|₁₆ + 333 13.1102 13¹|₈ – 388 15.2756 15⁹|₃₂ –
224 8.8189 8¹³|₁₆ + 279 10.9843 10³¹|₃₂ + 334 13.1496 13⁵|₃₂ – 389 15.3150 15⁵|₁₆ +
225 8.8583 8²⁷|₃₂ + 280 11.0236 11¹|₃₂ – 335 13.1890 13³|₁₆ + 390 15.3543 15¹¹|₃₂ +
226 8.8976 8²⁹|₃₂ – 281 11.0630 11¹|₁₆ + 336 13.2283 13⁷|₃₂ + 391 15.3937 15¹³|₃₂ –
227 8.9370 8¹⁵|₁₆ – 282 11.1024 11³|₃₂ + 337 13.2677 13⁹|₃₂ – 392 15.4331 15⁷|₁₆ –
228 8.9764 8³¹|₃₂ + 283 11.1417 11⁵|₃₂ – 338 13.3071 13⁵|₁₆ – 393 15.4724 15¹⁵|₃₂ +
229 9.0157 9¹|₃₂ – 284 11.1811 11³|₁₆ – 339 13.3465 13¹¹|₃₂ + 394 15.5118 15¹|₂ +
230 9.0551 9¹|₁₆ – 285 11.2205 11⁷|₃₂ + 340 13.3858 13³|₈ + 395 15.5512 15⁹|₁₆ –
231 9.0945 9³|₃₂ + 286 11.2598 11¹|₄ + 341 13.4252 13⁷|₁₆ – 396 15.5906 15¹⁹|₃₂ –
232 9.1339 9¹|₈ + 287 11.2992 11⁵|₁₆ – 342 13.4646 13¹⁵|₃₂ – 397 15.6299 15⁵|₈ +
233 9.1732 9³|₁₆ – 288 11.3386 11¹¹|₃₂ – 343 13.5039 13¹|₂ + 398 15.6693 15²¹|₃₂ +
234 9.2126 9⁷|₃₂ – 289 11.3780 11³|₈ + 344 13.5433 13¹⁷|₃₂ + 399 15.7087 15²³|₃₂ –
235 9.2520 9¹|₄ + 290 11.4173 11¹³|₃₂ + 345 13.5827 13¹⁹|₃₂ – 400 15.7480 15³|₄ –
236 9.2913 9⁹|₃₂ + 291 11.4567 11¹⁵|₃₂ – 346 13.6220 13⁵|₈ – 401 15.7874 15²⁵|₃₂ +
237 9.3307 9¹¹|₃₂ – 292 11.4961 11¹|₂ – 347 13.6614 13²¹|₃₂ + 402 15.8268 15¹³|₁₆ +
238 9.3701 9³|₈ – 293 11.5354 11¹⁷|₃₂ + 348 13.7008 13¹¹|₁₆ + 403 15.8661 15⁷|₈ –
239 9.4094 9¹³|₃₂ + 294 11.5748 11⁹|₁₆ + 349 13.7402 13³|₄ – 404 15.9055 15²⁹|₃₂ –
240 9.4488 9⁷|₁₆ + 295 11.6142 11⁵|₈ – 350 13.7795 13²⁵|₃₂ – 405 15.9449 15¹⁵|₁₆ +
241 9.4882 9¹|₂ – 296 11.6535 11²¹|₃₂ – 351 13.8189 13¹³|₁₆ + 406 15.9843 15³¹|₃₂ +
242 9.5276 9¹⁷|₃₂ – 297 11.6929 11¹¹|₁₆ + 352 13.8583 13²⁷|₃₂ + 407 16.0236 16¹|₃₂ –
243 9.5669 9⁹|₁₆ + 298 11.7323 11²³|₃₂ + 353 13.8976 13²⁹|₃₂ – 408 16.0630 16¹|₁₆ +
244 9.6063 9¹⁹|₃₂ + 299 11.7717 11²⁵|₃₂ – 354 13.9370 13¹⁵|₁₆ – 409 16.1024 16³|₃₂ +
245 9.6457 9²¹|₃₂ – 300 11.8110 11¹³|₁₆ – 355 13.9764 13³¹|₃₂ + 410 16.1417 16⁵|₃₂ –
246 9.6850 9¹¹|₁₆ – 301 11.8504 11²⁷|₃₂ + 356 14.0157 14¹|₃₂ – 411 16.1811 16³|₁₆ –
247 9.7244 9²³|₃₂ + 302 11.8898 11⁷|₈ + 357 14.0551 14¹|₁₆ – 412 16.2205 16⁷|₃₂ +
248 9.7638 9³|₄ + 303 11.9291 11¹⁵|₁₆ – 358 14.0945 14³|₃₂ + 413 16.2598 16¹|₄ +
249 9.8031 9¹³|₁₆ – 304 11.9685 11³¹|₃₂ – 359 14.1339 14¹|₈ + 414 16.2992 16⁵|₁₆ –
250 9.8425 9²⁷|₃₂ – 305 12.0079 12 + 360 14.1732 14³|₁₆ – 415 16.3386 16¹¹|₃₂ –
251 9.8819 9⁷|₈ + 306 12.0472 12¹|₁₆ – 361 14.2126 14⁷|₃₂ – 416 16.3780 16³|₈ +
252 9.9213 9²⁹|₃₂ + 307 12.0866 12³|₃₂ – 362 14.2520 14¹|₄ + 417 16.4173 16¹³|₃₂ +
253 9.9606 9³¹|₃₂ – 308 12.1260 12¹|₈ + 363 14.2913 14⁹|₃₂ + 418 16.4567 16¹⁵|₃₂ –
254 10.0000 10 309 12.1654 12⁵|₃₂ + 364 14.3307 14¹¹|₃₂ – 419 16.4961 16¹|₂ –
255 10.0394 10¹|₃₂ + 310 12.2047 12⁷|₃₂ – 365 14.3701 14³|₈ – 420 16.5354 16¹⁷|₃₂ +
256 10.0787 10³|₃₂ – 311 12.2441 12¹|₄ – 366 14.4094 14¹³|₃₂ + 421 16.5748 16⁹|₁₆ +
257 10.1181 10¹|₈ – 312 12.2835 12⁹|₃₂ + 367 14.4488 14⁷|₁₆ + 422 16.6142 16⁵|₈ –
258 10.1575 10⁵|₃₂ + 313 12.3228 12⁵|₁₆ + 368 14.4882 14¹|₂ – 423 16.6535 16²¹|₃₂ –
259 10.1969 10³|₁₆ + 314 12.3622 12³|₈ – 369 14.5276 14¹⁷|₃₂ – 424 16.6929 16¹¹|₁₆ +
260 10.2362 10¹|₄ – 315 12.4016 12¹³|₃₂ – 370 14.5669 14⁹|₁₆ + 425 16.7323 16²³|₃₂ +
261 10.2756 10⁹|₃₂ – 316 12.4409 12⁷|₁₆ + 371 14.6063 14¹⁹|₃₂ + 426 16.7717 16²⁵|₃₂ –
262 10.3150 10⁵|₁₆ + 317 12.4803 12¹⁵|₃₂ + 372 14.6457 14²¹|₃₂ – 427 16.8110 16¹³|₁₆ –
263 10.3543 10¹¹|₃₂ + 318 12.5197 12¹⁷|₃₂ – 373 14.6850 14¹¹|₁₆ – 428 16.8504 16²⁷|₃₂ +
264 10.3937 10¹³|₃₂ – 319 12.5591 12⁹|₁₆ – 374 14.7244 14²³|₃₂ + 429 16.8898 16⁷|₈ +
265 10.4331 10⁷|₁₆ – 320 12.5984 12¹⁹|₃₂ + 375 14.7638 14³|₄ + 430 16.9291 16¹⁵|₁₆ –
266 10.4724 10¹⁵|₃₂ + 321 12.6378 12⁵|₈ + 376 14.8031 14¹³|₁₆ – 431 16.9685 16³¹|₃₂ –
267 10.5118 10¹|₂ + 322 12.6772 12¹¹|₁₆ – 377 14.8425 14²⁷|₃₂ – 432 17.0079 17 +
268 10.5512 10⁹|₁₆ – 323 12.7165 12²³|₃₂ – 378 14.8819 14⁷|₈ + 433 17.0472 17¹|₁₆ –
269 10.5906 10¹⁹|₃₂ – 324 12.7559 12³|₄ + 379 14.9213 14²⁹|₃₂ + 434 17.0866 17³|₃₂ –
270 10.6299 10⁵|₈ + 325 12.7953 12²⁵|₃₂ + 380 14.9606 14³¹|₃₂ – 435 17.1260 17¹|₈ +
271 10.6693 10²¹|₃₂ + 326 12.8346 12²⁷|₃₂ – 381 15.0000 15 436 17.1654 17⁵|₃₂ +
272 10.7087 10²³|₃₂ – 327 12.8740 12⁷|₈ – 382 15.0394 15¹|₃₂ + 437 17.2047 17⁷|₃₂ –
273 10.7480 10³|₄ – 328 12.9134 12²⁹|₃₂ + 384 15.0787 15³|₃₂ – 438 17.2441 17¹|₄ –
274 10.7874 10²⁵|₃₂ + 329 12.9528 12¹⁵|₁₆ + 384 15.1181 15¹|₈ – 439 17.2835 17⁹|₃₂ +
275 10.8268 10¹³|₁₆ + 330 12.9921 13 – 385 15.1575 15⁵|₃₂ + 440 17.3228 17⁵|₁₆ +
343
Decimal Equivalents of
Fractions of an Inch
344
Metric Conversion Factors
British thermal unit (Btu/hour) 0.2930711 Watt (W) Foot per minute (fpm) 0.3048 Meter per minute
(m/min)
Celsius temperature (tC) 1.8tc + 32 = tF Fahrenheit
temperature (tF) Foot per minute (fpm) 0.00508 Meter per second (m/s)
Celsius temperature (tC) tC+273.15 = tK Kelvin temperature (tK) Foot per second (fps) 30.48 Centimeter per second
(cm/s)
Centimeter (cm) 0.03280840 Foot (ft)
Foot per second (fps) 18.288 Meter per minute
Centimeter (cm) 0.3937 Inch (in.) (m/min)
Centimeter (cm) 0.01 Meter (m) Foot per second (fps) 0.3048 Meter per second (m/s)
Centimeter (cm) 10 Millimeter (mm) Foot per second per second 0.3048 Meter per second per
second (m/s 2)
Centimeter per minute (cm/min) 0.3937008 Inch per minute (ipm)
Foot-pound-force (ft-lbf) 1.3558:8 Joule (J)
Centimeter per second (cm/s) 1.968504 Foot per minute (fpm)
Foot-poundal 0.04214011 Joule (J)
Centimeter per second (cm/s) 0.03280840 Foot per second (fps)
Foot-pound per hour (ft-lb/hr) 0.0003766161 Watt (W)
Cubic centimeter (cm3) 0.061023 Cubic Inch (in3)
Foot-pound per minute (ft-lb/min) 0.02259697 Watt (W)
Cubic foot (ft3) 0.02832 Cubic meter (m3)
Gallon, U.S. liquid (gal) 0.003785412 Cubic meter (m3)
Cubic foot (ft3) 28.31685 Liter (l)
Gallon, U.S. liquid (gal) 3.785412 Liter (l)
Cubic foot per minute (ft3/min) 0.004719474 Cubic meter per
second (m3/s) Gallon per minute, U.S. 3.785412 Liter per minute
liquid (gpm) (1/min)
Cubic foot per minute (ft3/min) 28.31685 Liter per minute (l/min)
Gallon per minute, U.S. 0.06309020 Liter per second
Cubic inch (in )
3
16.38706 Cubic centimeter (cm3)
liquid (gpm) (l/s)
Cubic inch (in3) 0.00001638706 Cubic meter (m3)
Gallon per minute, U.S. 0.003785412 Cubic meter per
Cubic inch (in )
3
16.387.06 Cubic millimeter (mm3) liquid (gpm) minute (m3/min)
Cubic meter (m3) 61,023.76 Cubic inch (in3) Gallon per minute, U.S. 0.00006309020 Cubic meter per
liquid (gpm) second (m3⁄s)
Cubic meter (m ) 3
35.3147 Cubic foot (ft )
3
Gram (g) 0.03527397 Ounce, (Av) (oz)
Cubic meter (m3) 264.1720 Gallon, U.S. liquid (gal)
Gram (g) 0.03215074 Ounce, (troy) (oz)
Cubic meter (m3) 1000.0 Liter (l)
Gram per cubic centimeter (g/cm3) 0.3612730 Pound per cubic
Cubic meter per minute (m3/min) 264.1720 Gallon per minute, inch (lb./in3)
U.S. liquid (gpm)
Horsepower (hp) 0.7456999 Kilowatt (kW)
Cubic meter per second (m3/s) 2118.880 Cubic foot per minute
(ft3/min) Horsepower (hp) 745.6999 Watt (W)
Cubic meter per second (m3/s) 15,850.32 Gallon per minute Horsepower, Metric (hp) 735.499 Watt (W)
U.S. liquid (gpm)
Inch (in.) 2.540 Centimeter (cm)
Cubic millimeter (mm3) 0.00006102376 Cubic inch (in3)
Inch (in.) 0.0254 Meter (m)
Dyne 0.00001 Newton (N)
Inch (in.) 25.4 Millimeter (mm)
Dyne-centimeter 0.0000001 Newton-meter (N-m)
Inch of mercury, 32˚F 3386.39 Newton per square
Fahrenheit temperature (tF) (TF–32)/1.8 = TC (tC) meter (N/m 2)
Fahrenheit temperature (tF) (tF+459.67)/1.8 = tK Kelvin temperature (tK) Inch per minute (Ipm) 2.54 Centimeter per
minute (cm/min)
Foot (ft) 30.48 Centimeter (cm)
Inch per minute (Ipm) 0.0254 Meter per minute
Foot (ft) 0.3048 Meter (m) (m/min)
Foot per hour (fph) 0.3048 Meter per hour (m/hr) Inch per minute (Ipm) 25.4 Millimeter per minute
(mm/min)
Foot per hour (fph) 0.00508 Meter per minute
(m/min) Joule (J) 0.0009478170 British thermal
unit (Btu)
Foot per hour (fph) 0.00008466667 Meter per second
(m/s) Joule (J) 0.7375621 Foot-pound-force (ft-lbf)
Foot per minute (fpm) 0.508 Centimeter per second Joule (J) 23.73036 Foot-Poundal
(cm/s)
Joule (J) 0.0002777778 Watt-hour (W-h)
345
Metric Conversion Factors MRC Bearing Services
Kelvin temperature (tK) 1.8tK – 459.67 = tF Fahrenheit tempera- Meter per hour (m/hr) 3.280840 Foot per hour (fph)
ture (tF)
Meter per hour (m/hr) 0.5468067 Foot per minute (fpm)
Kilogram (kg) 0.0009842064 ton (long)
Meter per minute (m/min) 3.280840 Foot per minute (fpm)
Kilogram (kg) 0.001 ton (metric)
Meter per minute (m/min) 0.05468067 Foot per second (fps)
Kilogram (kg) 0.001102311 Ton (short)
Meter per minute (m/min) 39.37008 Inch per minute (Ipm)
kilogram (kg) 35.27397 Ounce, (Av) (oz)
Meter per second (m/s) 11,811.02 Foot per hour (fph)
Kilogram (kg) 32.15074 Ounce, (Troy) (oz)
Meter per second (m/s) 196.8504 Foot per minute (fpm)
Kilogram (kg) 2.20462 Pound, (Av) (lb)
Meter per second (m/s) 3.280840 Foot per second (fps)
Kilogram-force (kgf) 9.80665 Newton (N)
or kilopound Microinch 0.0254 Micrometer or Micron
Kilogram-force per square meter 0.001422 Pound per square inch Newton (N) 0.1019716 Kilogram-force or kilo
(kgf/m2) (psi) pound (kgf)
Kilowatt (kW) 1.341022 Horsepower (hp) Newton (N) 3.596942 Ounce-force (ozf)
Kilonewton per square meter 0.1450377 Pound per square Newton (N) 0.2248089 Pound-force (lbf)
kN/m2) inch (psi)
Newton-meter (N-m) 10,000,000 Dyne-centimeter
Liter (l) 0.03531466 Cubic foot (ft3)
Newton-meter (N-m) 0.1019716 Kilogram-force-meter
Liter (l) 0.001 Cubic meter (m3) (kgf-m)
Liter (l) 0.2641720 Gallon, U.S. liquid (gal) Newton-meter (N-m) 141.6119 Ounce-force-inch
(ozf-in.)
Liter per minute (lpm) 0.03531466 Cubic foot per minute
(ft3/min) Newton-meter (N-m) 0.73756 Pound-force-foot (lbf-ft)
Liter per minute (lpm) 0.2641720 Gallon per minute, U.S. Newton-millimeter (N-mm) 0.1416119 Ounce-force-inch
liquid (gpm) (ozf-in.)
Liter per second (lps) 15.85032 Gallon per minute, U.S. Newton per meter (N/m) 0.06852178 Pound-force per foot
liquid (gpm) (lbf/ft)
Megapascal (MPa) 145.0377 Pound per square inch Newton per meter (N/m) 0.005710148 Pound-force per inch
(psi) (lbf/in.)
Meter (m) 39.37008 Inch (in.) Newton per square centimeter 1.450377 Pound per square
(N/cm2) inch (psi)
Meter (m) 3.280840 Foot (ft)
346
Metric Conversion Factors
Poundal 0.1382550 Newton (N) Square inch (in.2) 645.16 Square millimeter (mm2)
Pound-foot per second 0.1382550 Kilogram-meter per Square meter (m2) 1550.003 Square inch (in.2)
(lb-ft/s) second (kg-m/s)
Square millimeter (mm ) 2
0.0001076387 Square foot (ft2)
Pound-force (lbf) 4.448222 Newton (N)
Square millimeter (mm2) 0.001550003 Square inch (in.2)
Pound-inch per second 0.01152125 Kilogram-meter per
(lb-in./s) second (kg-m/s) Ton (metric) 1000 Kilogram (kg)
Pound per cubic inch 27.67990 Gram per cubic Ton (long) 1016.047 Kilogram (kg)
(lb/in.2) centimeter (g/cm3)
Ton (short) 907.1847 Kilogram (kg)
Pound per cubic foot 16.01846 Kilogram per cubic
Torr (mm Hg) 133.322 Pascal (Pa)
(lb/ft3) meter (kg/m3)
Watt (W) 3.412141 British thermal unit
Pound per foot (lb/ft) 14.59390 Newton per meter (N/m)
(Btu/hour)
Pound per inch (lb/in.) 175.1268 Newton per meter (N/m)
Watt (W) 2655.224 Foot-pound per hour
Pound per square foot 4.882429 Kilogram per square (ft-lb/hour)
(lb/ft2) meter (kg/m 2 )
Watt (W) 44.25372 Foot-pound per min.
Pound per square foot 47.88026 Newton per square (ft-lb/min)
(lb/ft2) meter (N/m2)
Watt (W) 0.001341022 Horsepower (hp)
Pound per square foot (lb/ft2) 47.88026 Pascal (Pa)
Watt (W) 0.001359621 Horsepower (metric)
Pound per square inch (psi) 0.063 Atmosphere (hp)
Pound per square inch (psi) 2.036 Inch of Mercury Watt-hour (W-h) 3600. Joule (J)
Yard (yd) 0.9144 Meter (m)
347
Trigonometric Solutions MRC Bearing Services
Solutions of Triangles
Right–angled Triangles
Sides and Angles Known Formulas for Sides and Angles to be Found
Sides a and c c = √ a2 – c2 c
sin C = a B= 90˚ – C
Oblique–angled Triangles
Sides and Angles Known Formulas for Sides and Angles to be Found
a × sin B a × sin C
Side a; angles A, B C= 180˚ – (A + B) b = ———— c = ————
sin A sin A
a × sin C a × sin C
Sides a, b; angle C tan A = ————–––– c = ———— B= 180˚ – (A + C)
b – a × cos C sin A
b × sin A a × sin C
Sides a, b; angle A sin B = ———— C= 180˚ – (A + B) c = ————
a sin A
b2 + c2 – a2 b × sin A
Sides a, b, c cos A = ————–– sin B = ———— C= 180˚ – (A + B)
2 bc a
348
Trigonometric Solutions
A = s2
A = 1 d2
√A
2
√A
s = 0.707d =
d = 1.414s = 1.414
Square
A = a√ d 2 – a 2 = b√ d 2 – b 2
A = ab
d = √ a2 + b 2
a = √ d2 – b2 = A ÷ b
b = √ d2 – a2 = A ÷ a
Rectangle
A = ab
a=A÷b
b=A÷a
Parallelogram
A = bc
a = √ b2 + c2
2
b = √ a2 – c2
c = √ a2 – b2
Right-angled Triangle
bh b
A = –– = –
2 2 √ ( a2 + b2 – c2
c2 – ––––––––––
2b )
2
If S = 1 (a + b + c), then
A = √S (S – a) (S – b) (S – c)
2
Acute-angled triangle
bh b
A = –– = –
2 2 √ ( c2 – a2 – b2
a2 – ––––––––––
2b )
2
If S = 1 (a + b + c), then
A = √S (S – a) (S – b) (S – c)
2
Obtuse-angled triangle
349
Trigonometric Solutions MRC Bearing Services
(a + b) h
A = ––––––––
2
Trapezoid
(H + h) a + bh + cH
A = –––––––––––––––––––
2
A trapezium can also be divided into two
triangles as indicated by the dotted line. The
area of each of the triangles is computed, and
the results added to find the area of the
trapezium.
Trapezium
√
n = number of sides.
α = 360˚ ÷ n β =180˚ – a
√ √
nsr n s s2
A= = ––– = –– R 2 – ––
2 2 4
s = 2 √R 2 – r 2
s2 s2
R= r 2 + –– , r= R 2 + –– ,
4 4
Regular Polygon
C = circumference.
A = πr 2 = 3.1416 r 2 = 0.7854 d 2
r × α × 3.1416= 0.01745 r α = 2
l = –––––––––––– A
–––
180 r
1 rl
A = – = 0.008727 αr 2
2
57.296 l 57.296 l
2 A = –––––––
a = ––––––– r = –––
Circular Sector r l α
c= 2 √ h(2 r – h) A = 1 – [r l – c (r – h)]
2
c2 + 4 h2
r= –––––––– l = 0.01745 rαa
8h
h = r – – √ 4 r 2 – c2
1 57.296 l
α = –––––––
2 r
Circular Segment
350
Trigonometric Solutions
A = π (R 2 – r 2) = 3.1416 (R 2 – r 2)
= 3.1416 (R + r) (R – r )
= 0.7854 (D 2– d 2) = 0.7854 (D + d ) (D – d )
Circular Ring
a = angle, in°s.
απ
A = ––– (R 2 – r 2) = 0.00873 α (R 2 – r 2)
360
απ
= –––––– (D 2 – d 2) = 0.00218 α (D 2 – d 2)
4 × 360
Circular Ring Sector
πr 2
A = r 2 – –– = 0.215 r 2
4
= 0.1075 c 2
Spandrel or Fillet
P= perimeter or circumference.
A= πab = 3.1416 ab.
√ 2 (a + b ) – (a––––––
A closer approximation is:
– b) 2
P = 3.1416 2 2
2.2
Ellipse
A = area BCD.
xy ab x y
(
A= –– – –– hyp. log – + –
2 2 a b )
Hyperbola
2
A= – xy
3
Parabola
351
Trigonometric Solutions MRC Bearing Services
Volumes of Solids
V = volume
s = 3 √V
V = s3
Cube
V= abc
V V V
a = –– b = –– c = ––
bc ac ab
Square Prism
Prism
1
V = – h × area of base.
3
If the base is a regular polygon with n sides,
√
and s= length of side, r= radius of inscribed
circle, and R= radius of circumscribed circle, then:
nsrh nsh s2
V= –––– = ––– R2 – ––
6 6 4
Pyramid
V= – (A1+A2+ √ A1 × A2 )
h
3
Frustrum of Pyramid
352
Trigonometric Solutions
Volumes of Solids
V = volume
Portion of Cylinder
V= ( 2 3
)
– a ± b × area ABC –––––
3
h
r±b
h
S = (ad ± b × length of arc ABC ) –––––
r±b
Use + when base area is larger, and – when
base area is less than one-half the base circle.
Portion of Cylinder
V = 3.1416 h (R 2 – r 2) = 0.7854 h (D 2 – d 2)
= 3.1416 ht (2 R – t) = 3.1416 ht (D – t)
= 3.1416 ht (2 r + t) = 3.1416 ht (d + t)
= 3.1416 ht (R + r) = 1.5708 ht (D + d)
Hollow Cylinder
s= √r 2 + h 2 =
√ d2
–– + h 2
4
Cone
Frustrum of Cone
A = area of surface.
4 pr 3 pd 3
V = –––– = ––– = 4.1888 r 3 = 0.5236 d 3
3 6
A = 4 pr 2 = p d 2 = 12.5664 r 2 = 3.1416 d 2
√
3
3V 3
r= ––– = 0.6204 √ V
4p
Sphere
353
Trigonometric Solutions MRC Bearing Services
Volumes of Solids
V = volume
Spherical Sector
V = 0.5236 h ––– (
3 c12 3 c22
4
+ ––– + h 2
4 )
A = 2 p r h = 6.2832 r h
√ ( c–––––––––––––
)
c22 2
2–c –4h
1
2 2 2
r= ––– +
4 8h
Spherical Zone
Spherical Wedge
4p
V = ––– (R 3 – r 3 ) = 4.1888 (R 3 – r 3 )
3
p
= –– (D 3 – d 3 ) = 0.5236 (D 3 – d 3 )
6
Hollow Sphere
A = area of surface.
V = 2p 2 R r 2 = 19.739 R r 2
p2
= –– Dd 2 = 2.4674 Dd 2
4
A = 4 p 2 R r = 39.478 R r
= p 2 D d = 9.8696 D d
Torus
354
Load Computations
Fig. 1
355
Load Computations MRC Bearing Services
Bearing Loads The reactions at the bearings act in a direction
opposite to the direction of the load. (See Fig. 3.) The
Radial and Thrust Loads straddle mounting is the most commonly used in
supporting shafts.
The overhung mounting produces an entirely
dissimilar result. In this, the load is applied at a point
outside of the two bearings. The effect of this is to
produce on the nearest bearing a load greater than
the original radial load. The load on the opposite end
bearing is generally relatively small. The load on the
bearing nearest to the point of application acts in the
same direction as that of the applied load. The load at
the other bearing acts in the opposite direction to that
of the applied load. (See Fig. 4.)
Thrust Loads
A Thrust or End Thrust load is one that acts in the
same direction as the axis of the shaft. Its effect is to
Fig. 2 push the entire circle of balls against the race
shoulder. The thrust may act from left to right or from
Radial Loads right to left, or it may alternate. In the majority of
A radial load is one applied at right angles to the axis cases, however, the thrust acts in one direction only.
of the shaft. This load passes from the shaft to the Horizontal mountings always require provision for
inner ring through the balls to the outer ring and thrust in both directions, although generally the thrust
thence to the housing. In some cases this condition in one direction may be only a ‘‘locating’’ or nominal
may be reversed, i. e., the radial load passing from a thrust. The ideal mounting for a ball bearing is where
revolving housing through the bearing to a stationary one bearing takes thrust in both directions. The
shaft. A radial load is sustained by not more than one- ‘‘opposed’’ method of mounting allows one bearing to
half of the balls in the bearing. take thrust in one direction, and the other bearing to
A radial load may be due to a single force, such as take thrust in the opposite direction.
weights of shaft and other revolving parts. More often, Combined Radial and Thrust Loads
however, the radial load is due to two or more One bearing of the pair sustains both radial and thrust
components such as tangential forces, separating loads. The resultant load is indicated by the diagonal
forces, overturning moments, etc. which are combined line, which also shows the direction in which the shaft
into one load acting in a single direction at right would move if not restrained by the bearing.
angles to the axis of the shaft and the axis of the
bearing.
Radial loads are supported by a pair of bearings
which are mounted in one of two different manners:
(1) Straddle; (2) Overhung. (See following page.)
In the straddle mounting, the radial load is divided in
inverse proportion to the distance from the point of
application of the load to the center of the bearing.
356
Load Computations
Bearing Loads
Straddle and Overhung Mountings
Fig. 3 Fig. 4
Straddle Mounting Overhung Mounting
L×a L×d
Radial load on Brg. I ––––– Radial load on Brg. III –––––
c e
L×b L×f
Radial load on Brg. II ––––– Radial load on Brg. IV –––––
c e
Example
Fig. 5 Fig. 6
357
Load Computations MRC Bearing Services
Fig. 8 Fig. 9
Straddle Mounting Overhung Mounting
358
Load Computations
Where loads are due both to driver and driven gears, Example: Horsepower (H) = 35
plot end view and determine resultant load graphically r.p.m. (R) of driver =1200
as shown below. Number of teeth in gears 18, 36, 72
Diametral pitch (p) of gears = 6
Proceed as follows:
Tooth pressure angle =17¹|₂˚
(1) Draw gears in correct position, preferably to full
or half scale.
Torque (Q) = 63000 × 35 =1840 in. lbs.
––––––––––
(2) Indicate direction of rotation with arrows. 1200
(3) Draw tangent (same direction as arrows).
Pitch dia. of driver = 18
–– = 3˝
(4) Complete triangle making hypotenuse (tooth load) 6
intersect driven gear. Tooth pressure angle = A =17¹|₂˚ cos17¹|₂ = .954
(5) Combine two forces as indicated in Fig. 11 2Q
Tooth Load = ––––––– × 1840 =1290 pounds
= 2–––––––
(6) Compute reactions on the bearings. D cos A 3 × .954
(See page 357)
Fig. 10
Fig. 11
Load on V 2170 × 4.8/10 =1040 lbs. at 600 r.p.m.
Load on VI 2170 – 1040 =1130 lbs. at 600 r.p.m.
359
Load Computations MRC Bearing Services
Radial Loads Due to Spur Gears
Idler and Intermediate Shafts Solution by Formulas
H = Horsepower Q = Torque
R = r.p.m. of driver D = Pitch dia. of driver
Z = 30˚ 35 + 30 = 32¹|₂˚
K = ––––––– cos 32¹|₂˚ = .843
2
Resultant tooth load = 252000 × 35 × .843 = 2170 lbs.
–––––––––––––––––
1200 × 3 × .954
Radial load on V 2170 × 4.8/10 = 1040 lbs. at 600 r.p.m.
Radial loads on VI 2170 – 1040 = 1130 lbs. at 600 r.p.m.
Radial loads on I, II, III and IV—see page 358.
360
Load Computations
Radial Loads Due to Spur Gears
Idler and Intermediate Shafts Solution by Formulas
Case 1: Where centers of driver, idler and driven shafts lie on one line. Direction of
rotation of gears is immaterial.
Fig. 12 Fig. 13
Fig. 14
Fig. 15
361
Load Computations MRC Bearing Services
362
Load Computations
Combination
Element
1 2 3 4 5 6
Single 4Q 2Q 2Q 4Q 2Q 4Q
––– –––––– ––– ––– –––––– –––
Planet s (s + p) s g (s + p) g
Resultant
Radial
Two 2Q Q 2Q 2Q Q 2Q
Load ––– –––––– ––– ––– –––––– –––
Planets s (s + p) s g (s + p) g
(L) on
III & IV
Three 4Q 2Q 4Q 4Q 2Q 4Q
––– –––––––– ––– ––– –––––––– –––
Planets 3s 3 (s + p) 3s 3g 3 (s + p) 3g
(g + s) g
Sun Gear R R × –––––– R R × –– 0 0
s s
Planet about s g g s g s g s
R × –––––– × –– R × –– R × –– R × –– R × –– R × –––––– × ––
own center (g + s) p p p p p (g + s) p
r.p.m.*
s g
Cage R × –––––– R 0 0 R R × ––––––
(g + s) (g + s)
Internal s (g + s)
0 0 R × –– R R × –––––– R
Gear g g
*In computing r.p.m. it may be more convenient to use number of teeth of gears, that is: s = number of teeth of sun gear; p = number of teeth of planet gear; g = number of
teeth of internal gear.
363
Load Computations MRC Bearing Services
V-Belt 1.5
Flat Belt
Single Ply 2.0
Double Ply 2.5
Triple Ply, Small Pulley Diameter 3.0
Rope
Pulley Groove Included Angle 45˚ 2.0
Pulley Groove Included Angle 45˚–60˚ 2.5
Chain 1.25
364
Load Computations
Fig. 20
365
Load Computations MRC Bearing Services
Thrust Loads
Aircraft, Motor Boats, Twist Drills
Thrust Due to Propellers
Aircraft propeller thrust in level flight (1) Brake horsepower of engine ‘‘H’’ 320 H
–––––
(2) Level flight air speed of aircraft in miles per hour ‘‘N’’ N
(Propeller efficiency assumed 85%)
Aircraft propeller thrust in level flight (1) Brake horsepower of engine ‘‘H’’ 375 H E
–––––––
(2) Level flight air speed of aircraft in miles per hour ‘‘N’’ N
(3) Propeller efficiency ‘‘E’’
Aircraft propeller thrust in climb (1) Brake horsepower of engine ‘‘H’’ 250 H
–––––
(2) Air speed of aircraft in climb in miles per hour ‘‘n’’ n
(3) r.p.m. of engine ‘‘R’’ at approx.
.9 ‘‘R’’ r.p.m.
(This formula does not apply to variable pitch propellers,
where full power and r.p.m.
are maintained in climb.)
Motor Boat propeller thrust (1) Brake horsepower of engine ‘‘H’’ 375 H E
–––––––
(2) Propeller efficiency (.60 to .70) ‘‘E’’ M
(3) Miles per hour of boat ‘‘M’’
(1) Brake horsepower of engine ‘‘H’’ 33000 H E
–––––––––
(2) Propeller efficiency (.60 to .70) ’‘E’’ rF
(3) r.p.m. of propeller
(4) Pitch of propeller in feet ‘‘F’’
366
Load Computations
Thrust load on front wheel bearings due to side skid (1) Weight on front axle .3 J W
Radial load on rear wheel bearings (1) Weight on rear axle .64 K W
Thrust load on rear wheel bearings due to side skid (1) Weight on rear axle .3 K W
367
Load Computations MRC Bearing Services
Mounting
Bending Stress
SB at x 10.2 L a x
SB = ––––––––– 10.2 L d x
SB = –––––––––
D3 c D3 e
SB at y 10.2 L b y
SB = ––––––––– 10.2 L (d – y)
SB = –––––––––––
D3 c B3
Torsional
Stress 321,000 H or –––––
SQ = ––––––––– 5.1 Q
SQ R D3 D3
Shaft
Deflection
3.40 L a x (c 2 – x 2 – a 2) 3.40 L d x (e2 – x2)
M at x M = –––––––––––––––––––– M = ––––––––––––––––
c E D4 e E D4
√
1 2B
Supports Calculate Y1 = a – + –––
MM 3 3a
6.80 L a2 b2 6.80 L d2 f
Deflection M = –––––––––– M = –––––––––
at c E D4 E B4
Load
M at L
368
Load Computations
Thrust Loads
(Note: Mean Pitch Diameter taken on pitch line ¹|₃ face length from pitch diameter, is
approximately at the center of the contact area of the gears.)
2QX
THRUST = ––––– V = Mean Pitch Diameter of Bevel Drive Gear in inches
v
(taken on pitch line ¹|₃ face length from pitch dia.)
X = See below
A = Tooth Pressure Angle
Q = Engine Torque in inch-pounds
u = Pitch Angle of Driving Gear
G = Gear Ratio
No. of teeth in driving gear
Tan u = –––––––––––––––––––––––
No. of teeth in driven gear
v = Mean Pitch Diameter of Bevel Driving Gear in
inches (taken on pitch line ¹|₃ face length from pitch dia.)
Value of X
Driving Gear: X = TAN A SIN u
Driven Gear: X = TAN A COS u
369
Load Computations MRC Bearing Services
Fig. 23 Fig. 24
Overhung Driving Gear Straddle Driving Gear
P Tp Tg v/2 V/2
1580 110 490 1.17 5.18
Brg. IIa 1580 – 830 = 750 490 – 260 = 230 110 × 1.17/2.85 = 50
√ 750 2 + (230 – 50)2 = 770 pounds radial load at 1200 r.p.m.
370
Product Index
Numerical Order
Series
Designation Product Page
100 . . . . . . . . . . . . . .Self-Aligning Ball Bearing with Cylindrical Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
100KR . . . . . . . . . . .Single-Row 15° Angular Contact Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107
100KRD . . . . . . . . . .Single-Row 15° Angular Contact Duplex Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108
100KS . . . . . . . . . . .Single-Row Deep Groove Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
100KSF . . . . . . . . . .Single-Row Deep Groove Ball Bearing With One Shield . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
100KSFF . . . . . . . . .Single-Row Deep Groove Ball Bearing With Two Shields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
100KSFFG . . . . . . . .Single-Row Deep Groove Ball Bearing With Two Shields And Snap Ring . . . . . . . . . . . . . . . . . . . . . . . . . .47
100KSFG . . . . . . . . .Single-Row Deep Groove Ball Bearing With One Shield And Snap Ring . . . . . . . . . . . . . . . . . . . . . . . . . . .47
100KSFZ . . . . . . . . .Single-Row Deep Groove Ball Bearing With One Shield And One Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
100KSG . . . . . . . . . .Single-Row Deep Groove Ball Bearing With Snap Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
100KSZ . . . . . . . . . .Single-Row Deep Groove Ball Bearing With One Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
100KSZZ . . . . . . . . .Single-Row Deep Groove Ball Bearing With Two Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
100KSZZG . . . . . . .Single-Row Deep Groove Ball Bearing With Two Seals And Snap Ring . . . . . . . . . . . . . . . . . . . . . . . . . . .47
100M . . . . . . . . . . . .Single-Row Maximum Capacity Filling Notch Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
100MF . . . . . . . . . . .Single-Row Maximum Capacity Filling Notch Ball Bearing With One Shield . . . . . . . . . . . . . . . . . . . . . . . .58
100R . . . . . . . . . . . .Single-Row 15° Angular Contact Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106
100RD . . . . . . . . . . .Single-Row 15° Angular Contact Duplex Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106
100S . . . . . . . . . . . . .Single-Row Deep Groove Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
11200E . . . . . . . . . .Self-Aligning Ball Bearing With Extended Inner Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
11300E . . . . . . . . . .Self-Aligning Ball Bearing With Extended Inner Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
1200 . . . . . . . . . . . . .Self-Aligning Ball Bearing With Cylindrical Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
1200E . . . . . . . . . . .Self-Aligning Ball Bearing With Cylindrical Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
1200EK . . . . . . . . . .Self-Aligning Ball Bearing With Tapered Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
1200K . . . . . . . . . . .Self-Aligning Ball Bearing With Tapered Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
1300 . . . . . . . . . . . . .Self-Aligning Ball Bearing With Cylindrical Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
1300E . . . . . . . . . . .Self-Aligning Ball Bearing With Cylindrical Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
1300EK . . . . . . . . . .Self-Aligning Ball Bearing With Tapered Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
1300K . . . . . . . . . . .Self-Aligning Ball Bearing With Tapered Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
1400 . . . . . . . . . . . . .Self-Aligning Ball Bearing With Cylindrical Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
1800S . . . . . . . . . . .Single-Row Deep Groove Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
1800SFP . . . . . . . . .Single-Row Deep Groove Ball Bearing With One Shield . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
1800SFFP . . . . . . . .Single-Row Deep Groove Ball Bearing With Two Shields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
1800SZ . . . . . . . . . .Single-Row Deep Groove Ball Bearing With One Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
1800SZZ . . . . . . . . .Single-Row Deep Groove Ball Bearing With Two Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
1900R . . . . . . . . . . .Single-Row 15° Angular Contact Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104
1900RD . . . . . . . . . .Single-Row 15° Angular Contact Duplex Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105
1900S . . . . . . . . . . .Single-Row Deep Groove Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
1900SFP . . . . . . . . .Single-Row Deep Groove Ball Bearing With One Shield . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
1900SFFP . . . . . . . .Single-Row Deep Groove Ball Bearing With Two Shields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
1900SZ . . . . . . . . . .Single-Row Deep Groove Ball Bearing With One Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
1900SZZ . . . . . . . . .Single-Row Deep Groove Ball Bearing With Two Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
200M . . . . . . . . . . . .Single-Row Maximum Capacity Filling Notch Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
200MF . . . . . . . . . . .Single-Row Maximum Capacity Filling Notch Ball Bearing With One Shield . . . . . . . . . . . . . . . . . . . . . . . .59
200MFF . . . . . . . . .Single-Row Maximum Capacity Filling Notch Ball Bearing With Two Shields . . . . . . . . . . . . . . . . . . . . . . . .59
200MFFG . . . . . . . .Single-Row Maximum Capacity Filling Notch Ball Bearing With Two Shields And Snap Ring . . . . . . . . . .59
200MFG . . . . . . . . .Single-Row Maximum Capacity Filling Notch Ball Bearing With One Shield And Snap Ring . . . . . . . . . . .59
200MG . . . . . . . . . . .Single-Row Maximum Capacity Filling Notch Ball Bearing With Snap Ring . . . . . . . . . . . . . . . . . . . . . . . . .59
200R . . . . . . . . . . . .Single-Row 15° Angular Contact Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109
200RD . . . . . . . . . . .Single-Row 15° Angular Contact Duplex Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110
200S . . . . . . . . . . . . .Single-Row Deep Groove Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
200SF . . . . . . . . . . .Single-Row Deep Groove Ball Bearing With One Shield . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
371
Product Index
Numerical Order M R C Bearing Services
Series
Designation Product Page
200SFF . . . . . . . . . .Single-Row Deep Groove Ball Bearing With Two Shields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
200SFFC . . . . . . . .Single-Row Deep Groove Cartridge Ball Bearing With Two Shields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
200SFFG . . . . . . . . .Single-Row Deep Groove Ball Bearing With Two Shields And Snap Ring . . . . . . . . . . . . . . . . . . . . . . . . . .48
200S-HYB#1 . . . . . .Single Row Hybrid Deep Groove Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
200SFF-HYB#1 . . .Single Row Hybrid Deep Groove Ball Bearing with Two Shields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
200SZZ-HYB#1 . . . .Single Row Hybrid Deep Groove Ball Bearing with Two Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
200SFFX . . . . . . . . .Single-Row Deep Groove Ball Bearing With Two Shields And Tapered bore . . . . . . . . . . . . . . . . . . . . . . .204
200SFZ . . . . . . . . . .Single-Row Deep Groove Ball Bearing With One Shield And One Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
200SG . . . . . . . . . . .Single-Row Deep Groove Ball Bearing With Snap Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
200SZ . . . . . . . . . . .Single-Row Deep Groove Ball Bearing With One Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
200SZZ . . . . . . . . . .Single-Row Deep Groove Ball Bearing With Two Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
200SZZC . . . . . . . .Single-Row Deep Groove Cartridge Ball Bearing With Two Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
200SZZG . . . . . . . . .Single-Row Deep Groove Ball Bearing With Two Seals And Snap Ring . . . . . . . . . . . . . . . . . . . . . . . . . . .48
200SZZX . . . . . . . . .Single-Row Deep Groove Ball Bearing With Two Seals And Tapered Bore . . . . . . . . . . . . . . . . . . . . . . . .204
2200 . . . . . . . . . . . . .Self-Aligning Ball Bearing With Cylindrical Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
2200E . . . . . . . . . . .Self-Aligning Ball Bearing With Cylindrical Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
2200EK . . . . . . . . . .Self-Aligning Ball Bearing With Tapered Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
2200K . . . . . . . . . . .Self-Aligning Ball Bearing With Tapered Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
22002RS1 . . . . . . . .Self-Aligning Ball Bearing With Cylindrical Bore And Two Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
22002RS1K . . . . . .Self-Aligning Ball Bearing With Tapered Bore And Two Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
2200E2RS1 . . . . . .Self-Aligning Ball Bearing With Cylindrical Bore And Two Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
2200E2RS1K . . . . . .Self-Aligning Ball Bearing With Tapered Bore and Two Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
2300 . . . . . . . . . . . . .Self-Aligning Ball Bearing With Cylindrical Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
2300E . . . . . . . . . . .Self-Aligning Ball Bearing With Cylindrical Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
2300EK . . . . . . . . . .Self-Aligning Ball Bearing With Tapered Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
2300E2RS1 . . . . . .Self-Aligning Ball Bearing With Cylindrical Bore And Two Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
2300K . . . . . . . . . . .Self-Aligning Ball Bearing With Tapered Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
30 . . . . . . . . . . . . . . .Single-Row Deep Groove Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
30F . . . . . . . . . . . . . .Single-Row Deep Groove Ball Bearing With One Shield . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
30FF . . . . . . . . . . . . .Single-Row Deep Groove Ball Bearing With Two Shields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
30Z . . . . . . . . . . . . . .Single-Row Deep Groove Ball Bearing With One Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
30ZZ . . . . . . . . . . . . .Single-Row Deep Groove Ball Bearing With Two Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
300M . . . . . . . . . . . .Single-Row Maximum Capacity Filling Notch Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
300MF . . . . . . . . . . .Single-Row Maximum Capacity Filling Notch Ball Bearing With One Shield . . . . . . . . . . . . . . . . . . . . . . . .60
300MFF . . . . . . . . .Single-Row Maximum Capacity Filling Notch Ball Bearing With Two Shields . . . . . . . . . . . . . . . . . . . . . . . .60
300MFFG . . . . . . . .Single-Row Maximum Capacity Filling Notch Ball Bearing With Two Shields And Snap Ring . . . . . . . . . .60
300MFG . . . . . . . . .Single-Row Maximum Capacity Filling Notch Ball Bearing With One Shield And Snap Ring . . . . . . . . . . .60
300MG . . . . . . . . . . .Single-Row maximum Capacity Filling Notch Ball Bearing With Snap Ring . . . . . . . . . . . . . . . . . . . . . . . . .60
300R . . . . . . . . . . . .Single-Row 15° Angular Contact Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111
300RD . . . . . . . . . . .Single-Row 15° Angular Contact Duplex Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
300RDM . . . . . . . . .Single-Row Dynamometer Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .207
300S . . . . . . . . . . . . .Single-Row Deep Groove Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
300SF . . . . . . . . . . .Single-Row Deep Groove Ball Bearing With One Shield . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
300SFF . . . . . . . . . .Single-Row Deep Groove Ball Bearing With Two Shields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
300SFFC . . . . . . . .Single-Row Deep Groove Cartridge Ball Bearing With Two Shields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
300SFFG . . . . . . . . .Single-Row Deep Groove Ball Bearing With Two Shields And Snap Ring . . . . . . . . . . . . . . . . . . . . . . . . . .49
300SFG . . . . . . . . .Single-Row Deep Groove Ball Bearing With One Shield And Snap Ring . . . . . . . . . . . . . . . . . . . . . . . . . . .49
300SFZ . . . . . . . . . .Single-Row Deep Groove Ball Bearing With One Shield And One Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
300SG . . . . . . . . . . .Single-Row Deep Groove Ball Bearing With Snap Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
300S-HYB#1 . . . . . .Single Row Hybrid Deep Groove Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
300SFF-HYB#1 . . . .Single Row Hybrid Deep Groove Ball Bearing with Two Shields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
300SZZ-HYB#1 . . . .Single Row Hybrid Deep Groove Ball Bearing with Two Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
372
Product Index
Numerical Order
Series
Designation Product Page
300SWI . . . . . . . . . .Single-Row Deep Groove Ball Bearing With Wide Inner Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .231
300SZ . . . . . . . . . . .Single-Row Deep Groove Ball Bearing With One Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
300SZZ . . . . . . . . . .Single-Row Deep Groove Ball Bearing With Two Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
300SZZC . . . . . . . .Single-Row Deep Groove Cartridge Ball Bearing With Two Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
300SZZG . . . . . . . . .Single-Row Deep Groove Ball Bearing With Two Seals And Snap Ring . . . . . . . . . . . . . . . . . . . . . . . . . . .49
300WI . . . . . . . . . . . .Single-Row Maximum Capacity Filling Notch Ball Bearing With Wide Inner Ring . . . . . . . . . . . . . . . . . . .231
400M . . . . . . . . . . . .Single-Row Maximum Capacity Filling Notch Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
400MF . . . . . . . . . . .Single-Row Maximum Capacity Filling Notch Ball Bearing With One Shield . . . . . . . . . . . . . . . . . . . . . . . .61
400MFF . . . . . . . . .Single-Row Maximum Capacity Filling Notch Ball Bearing With Two Shields . . . . . . . . . . . . . . . . . . . . . . . .61
400MG . . . . . . . . . . .Single-Row Maximum Capacity Filling Notch Ball Bearing With Snap Ring . . . . . . . . . . . . . . . . . . . . . . . . .61
400R . . . . . . . . . . . .Single-Row 15° Angular Contact Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113
400RD . . . . . . . . . . .Single-Row 15° Angular Contact Duplex Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113
400S . . . . . . . . . . . . .Single-Row Deep Groove Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
400SF . . . . . . . . . . .Single-Row Deep Groove Ball Bearing With One Shield . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
400SFF . . . . . . . . . .Single-Row Deep Groove Ball Bearing With Two Shields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
487500 . . . . . . . . . . .Single-Row Felt Seal Replacement With One Shield, One Seal And Snap Ring . . . . . . . . . . . . . . . . . . . .225
488000 . . . . . . . . . . .Single-Row Felt Seal Replacement With Two Seals And Snap Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . .225
488500 . . . . . . . . . . .Single-Row Felt Seal Replacement With Two Seals And Snap Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . .225
5200C . . . . . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
5200CF . . . . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With One Shield . . . . . . . . . . . . . . . . . . . . . .93
5200CFF . . . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With Two Shields . . . . . . . . . . . . . . . . . . . . .93
5200CFFG . . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With Two Shields And Snap Ring . . . . . . . .93
5200CFG . . . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With One Shield And Snap Ring . . . . . . . . .93
5200CFZ . . . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With One Shield And One Seal . . . . . . . . . .93
5200CFZG . . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With One Shield,
One Seal And Snap Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
5200CG . . . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With Snap Ring . . . . . . . . . . . . . . . . . . . . . . .93
5200CZ . . . . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With One Seal . . . . . . . . . . . . . . . . . . . . . . . .93
5200CZG . . . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With One Seal And Snap Ring . . . . . . . . . .93
5200CZZ . . . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With Two Seals . . . . . . . . . . . . . . . . . . . . . . .93
5200CZZG . . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With Two Seals And Snap Ring . . . . . . . . . .93
5200C1 . . . . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing, Extra Width . . . . . . . . . . . . . . . . . . . . . . . . . .93
5200M . . . . . . . . . . .Double-Row Angular Contact Filling Notch Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
5200MF . . . . . . . . . .Double-Row Angular Contact Filling Notch Ball Bearing With One Shield . . . . . . . . . . . . . . . . . . . . . . . . . .96
5200MFF . . . . . . . .Double-Row Angular Contact Filling Notch Ball Bearing With Two Shields . . . . . . . . . . . . . . . . . . . . . . . . .96
5200MFFG . . . . . . .Double-Row Angular Contact Filling Notch Ball Bearing With Two Shields And Snap Ring . . . . . . . . . . . .96
5200MFG . . . . . . . .Double-Row Angular Contact Filling Notch Ball Bearing With One Shield And Snap Ring . . . . . . . . . . . . .96
5200MFZ . . . . . . . .Double-Row Angular Contact Filling Notch Ball Bearing With One Shield And One Seal . . . . . . . . . . . . . .96
5200MFZG . . . . . . .Double-Row Angular Contact Filling Notch Ball Bearing With One Shield, One Seal And Snap Ring . . . .96
5200MG . . . . . . . . . .Double-Row Angular Contact Filling Notch Ball Bearing With Snap Ring . . . . . . . . . . . . . . . . . . . . . . . . . . .96
5200MZ . . . . . . . . . .Double-Row Angular Contact Filling Notch Ball Bearing With One Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
5200MZG . . . . . . . .Double-Row Angular Contact Filling Notch Ball Bearing With One Seal And Snap Ring . . . . . . . . . . . . . . .96
5200MZZ . . . . . . . .Double-Row Angular Contact Filling Notch Ball Bearing With Two Seals . . . . . . . . . . . . . . . . . . . . . . . . . . .96
5200MZZG . . . . . . .Double-Row Angular Contact Filling Notch Ball Bearing With Two Seals And Snap Ring . . . . . . . . . . . . . .96
5200M1 . . . . . . . . . .Double-Row Angular Contact Filling Notch Ball Bearing, Extra Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
5200SB . . . . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
5200SBKF . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With One Shield . . . . . . . . . . . . . . . . . . . . . .93
5200SBKFF . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With Two Shields . . . . . . . . . . . . . . . . . . . . .93
5200SBKFFG . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With Two Seals And Snap Ring . . . . . . . . . .93
5200SBKFG . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With One Shield And Snap Ring . . . . . . . . .93
5200SBKG . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With Snap Ring . . . . . . . . . . . . . . . . . . . . . . .93
5200SBKZ . . . . . . .Double-Row Angular Contact Non-Filling Notch Contact Ball Bearing With One Seal . . . . . . . . . . . . . . . . .93
373
Product Index
Numerical Order M R C Bearing Services
Series
Designation Product Page
5200SBKZZ . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With Two Seals . . . . . . . . . . . . . . . . . . . . . . .93
5300C . . . . . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
5300CF . . . . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With One Shield . . . . . . . . . . . . . . . . . . . . . .94
5300CFF . . . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With Two Shields . . . . . . . . . . . . . . . . . . . . .94
5300CFFG . . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With Two Shields And Snap Ring . . . . . . . .94
5300CFG . . . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With One Shield And Snap Ring . . . . . . . . .94
5300CFZ . . . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With One Shield And One Seal . . . . . . . . . .94
5300CFZG . . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With One Shield,
One Seal And Snap Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
5300CG . . . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With Snap Ring . . . . . . . . . . . . . . . . . . . . . . .94
5300CZ . . . . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With One Seal . . . . . . . . . . . . . . . . . . . . . . . .94
5300CZG . . . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With One Seal And Snap Ring . . . . . . . . . .94
5300CZZ . . . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With Two Seals . . . . . . . . . . . . . . . . . . . . . . .94
5300CZZG . . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With Two Seals And Snap Ring . . . . . . . . . .94
5300C1 . . . . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing, Extra Width . . . . . . . . . . . . . . . . . . . . . . . . . .94
5300M . . . . . . . . . . .Double-Row Angular Contact Filling Notch Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97
5300MF . . . . . . . . . .Double-Row Angular Contact Filling Notch Ball Bearing With One Shield . . . . . . . . . . . . . . . . . . . . . . . . . .97
5300MFF . . . . . . . .Double-Row Angular Contact Filling Notch Ball Bearing With Two Shields . . . . . . . . . . . . . . . . . . . . . . . . .97
5300MFFG . . . . . . .Double-Row Angular Contact Filling Notch Ball Bearing With Two Shields And Snap Ring . . . . . . . . . . . .97
5300MFG . . . . . . . .Double-Row Angular Contact Filling Notch Ball Bearing With One Shield And Snap Ring . . . . . . . . . . . . .97
5300MFZ . . . . . . . .Double-Row Angular Contact Filling Notch Ball Bearing With One Shield And One Seal . . . . . . . . . . . . . .97
5300MFZG . . . . . . .Double-Row Angular Contact Filling Notch Ball Bearing With One Shield, One Seal and Snap Ring . . . .97
5300MZ . . . . . . . . . .Double-Row Angular Contact Filling Notch Ball Bearing With One Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . .97
5300MZZ . . . . . . . .Double-Row Angular Contact Filling Notch Ball Bearing With Two Seals . . . . . . . . . . . . . . . . . . . . . . . . . . .97
5300MZZG . . . . . . .Double-Row Angular Contact Filling Notch Ball Bearing With Two Seals And Snap Ring . . . . . . . . . . . . . .97
5300M1 . . . . . . . . . .Double-Row Angular Contact Filling Notch Ball Bearing, Extra Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97
5300SB . . . . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
5300SBKF . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With One Shield . . . . . . . . . . . . . . . . . . . . . .94
5300SBKFF . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With Two Shields . . . . . . . . . . . . . . . . . . . . .94
5300SBKFFG . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With Two Shields And Snap Ring . . . . . . . .94
5300SBKFG . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With One Shield And Snap Ring . . . . . . . . .94
5300SBKG . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With Snap Ring . . . . . . . . . . . . . . . . . . . . . . .94
5300SBKZ . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With One Seal . . . . . . . . . . . . . . . . . . . . . . . .94
5300SBKZZ . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing With Two Seals . . . . . . . . . . . . . . . . . . . . . . .94
5400C . . . . . . . . . . .Double-Row Angular Contact Non-Filling Notch Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
7100 . . . . . . . . . . . . .Single-Row 29° Angular Contact Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122
7100D . . . . . . . . . . .Single-Row 29° Angular Contact Duplex Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122
7100KR . . . . . . . . . .Single-Row 29° Angular Contact Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123
7100KRD . . . . . . . . .Single-Row 29° Angular Contact Duplex Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124
7200 . . . . . . . . . . . . .Single-Row 29° Angular Contact Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125
7200D . . . . . . . . . . .Single-Row 29° Angular Contact Duplex Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126
7200P . . . . . . . . . . .Single-Row 40° Angular Contact Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .136
7200PD . . . . . . . . . .Single-Row 40° Angular Contact Duplex Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137
7200PJ . . . . . . . . . . .Single-Row 40° Angular Contact Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148
7200PJD . . . . . . . . .Single-Row 40° Angular Contact Duplex Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148
7300 . . . . . . . . . . . . .Single-Row 29° Angular Contact Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127
7300D . . . . . . . . . . .Single-Row 29° Angular Contact Duplex Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128
7300P . . . . . . . . . . .Single-Row 40° Angular Contact Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .138
7300PD . . . . . . . . . .Single-Row 40° Angular Contact Duplex Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .139
7300PJ . . . . . . . . . . .Single-Row 40° Angular Contact Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .149
7300PJD . . . . . . . . .Single-Row 40° Angular Contact Duplex Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .149
7400 . . . . . . . . . . . . .Single-Row 29° Angular Contact Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129
374
Product Index
Numerical Order
Series
Designation Product Page
7400D . . . . . . . . . . .Single-Row 29° Angular Contact Duplex Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129
7400P . . . . . . . . . . .Single-Row 40° Angular Contact Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140
7400PD . . . . . . . . . .Single-Row 40° Angular Contact Duplex Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140
7400PJ . . . . . . . . . . .Single-Row 40° Angular Contact Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150
7400PJD . . . . . . . . .Single-Row 40° Angular Contact Duplex Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150
8000 . . . . . . . . . . . . .Single-Row Felt Seal Replacement With One Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .224
8200 . . . . . . . . . . . . .PumPac Duplex Pair Of Angular Contact Ball Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .159
8200AAB . . . . . . . . .PumPac Triplex Set Of Angular Contact Ball Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .161
8200BB . . . . . . . . . .PumPac Diamond Duplex Pair Of Angular Contact Ball Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .160
8300 . . . . . . . . . . . . .PumPac Duplex Pair Of Angular Contact Ball Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .159
8300AAB . . . . . . . . .PumPac Triplex Set Of Angular Contact Ball Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .161
8300BB . . . . . . . . . .PumPac Diamond Duplex Pair Of Angular Contact Ball Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .160
8500 . . . . . . . . . . . . .Single-Row Felt Seal Replacement With One Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .224
8600 . . . . . . . . . . . . .Single-Row Felt Seal Replacement With One Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .224
87000 . . . . . . . . . . . .Single-Row Felt Seal Replacement With One Shield And One Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .224
87500 . . . . . . . . . . . .Single-Row Felt Seal Replacement With One Shield And One Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .224
88000 . . . . . . . . . . . .Single-Row Felt Seal Replacement With Two Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .225
88500 . . . . . . . . . . . .Single-Row Felt Seal Replacement With Two Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .225
9100UK . . . . . . . . . .Single-Row 29° Split Inner Ring Angular Contact Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .168
9200U . . . . . . . . . . .Single-Row 29° Split Inner Ring Angular Contact Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .168
9200UP . . . . . . . . . .Single-Row 40° Split Inner Ring Angular Contact Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .171
9300U . . . . . . . . . . .Single-Row 29° Split Inner Ring Angular Contact Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .169
9300UP . . . . . . . . . .Single-Row 40° Split Inner Ring Angular Contact Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .171
97000U . . . . . . . . . .Matched Set Of 9000UDT And 7000DT 29° Angular Contact Ball Bearings . . . . . . . . . . . . . . . . . . . . . . .178
97000UP . . . . . . . . .Matched Set Of 9000UPDT And 7000 PDT 40° Angular Contact Ball Bearings . . . . . . . . . . . . . . . . . . . .180
375
Product Index
Numerical Order M R C Bearing Services
Series
Designation Product Page
R2-R24 . . . . . . . . . . .Single-Row Deep Groove Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
R2A-R4A . . . . . . . . .Single-Row Deep Groove Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
R2AF-R4AF . . . . . .Single-Row Deep Groove Ball Bearing With One Shield . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
R2AFF-R4AFF . . . .Single-Row Deep Groove Ball Bearing With Two Shields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
R2AZ-R4AZ . . . . . .Single-Row Deep Groove Ball Bearing With One Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
R2AZZ-R4AZZ . . . .Single-Row Deep Groove Ball Bearing With Two Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
R2F-R24F . . . . . . . .Single-Row Deep Groove Ball Bearing With One Shield . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
R2FF-R24FF . . . . .Single-Row Deep Groove Ball Bearing With Two Shields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
R2Z-R20Z . . . . . . . .Single-Row Deep Groove Ball Bearing With One Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
R2ZZ-R20ZZ . . . . .Single-Row Deep Groove Ball Bearing With Two Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
SNW . . . . . . . . . . . . .Adapter Sleeve For Tapered Bore Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .204
W00 . . . . . . . . . . . . .Lockwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .326
WC87000 . . . . . . . . .Single-Row Felt Seal Replacement With One Shield And One Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .224
WC87500 . . . . . . . . .Single-Row Felt Seal Replacement With One Shield And One Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .224
XLS . . . . . . . . . . . . .Single-Row 15° Angular Contact Ball Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114
X0 . . . . . . . . . . . . . . .Ex-Cell-O Spindle Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .199
376
377
378
379
380
381
382
383
384
BEARING
INTRODUCTION ENGINEERING DATA MARATHON SERIES MADE-TO-ORDER
SPECIFICATION TABLES
HDi Series
Heavy Duty Cast Iron
XDs Series
Extreme Duty Cast Stainless
MRC Bearing Services
385
MRC Bearing Services
A Composite Housing
with Integrated Performance Features
• A polyurethane-filled housing base enables the unit to
meet flush with its mounting surface. Flush surface-to-
surface mounting eliminates gaps — potential areas for
contaminants to collect.
• 300 Series stainless steel bolt hole inserts provide
added strength to each housing foot and prevent
corrosion.
• Marathon Series units are available in the following
housing designs to meet the needs of most food and
beverage processing applications:
– pillow blocks
– two- or four-bolt flange
The Marathon Series’ composite housing resists citric
acids, cooking fats and most chemicals used in food and – tapped base
beverage processing. It is constructed of a thermoplastic – three-bolt bracket flange
composite material that can be up to 61% lighter than cast – narrow and wide slot take-up
iron housings. Its spherical bore accommodates the insert
– low backing height pillow block
bearing’s spherical outer surface, enabling the unit to
fully compensate for initial bearing seating misalignment. – low profile two- and three-bolt flange
– four-bolt piloted flange
Plus, the housing is loaded with design and
performance advantages: – hanger
Polyurethane-filled
base. No gaps where
contaminants can
collect.
Insert bearing is
prelubricated with
USDA approved
grease.
304 stainless
steel double Polyamide Cage.
contact seal
and flinger. Light gray
polyamide composite
housing resists
corrosion.
Stainless steel
bolt hole inserts.
386
HDi ZMaRC® Coated Cast Iron Units with
ZMaRC coated Insert Bearings
The heavy duty cast iron housings, protected with • Open spaces on bases and backs of ZMaRC-coated
MRC’s proven ZMaRC coating, eliminate the flaking housings are filled with polyurethane, eliminating areas
problems associated with nickel-plated products. The where moisture and product can collect, resulting in a
housings are matched with our ZMaRC-plated, lubed-for- more sanitary housing design.
life, quality insert bearings. • All HDi units are factory lubed-for-life with USDA
The HDi series provides a number of cost-saving and approved H1 grease.
performance benefits. As with all Marathon products, • Two-part sealing for maximum protection
MRC’s patented two-part stainless steel seals allow the
units to operate in heavy washdown environments without Like all Marathon bearing units, Marathon HDi units
regreasing. And since there is no need for relubrication, contain an AISI 304 stainless steel inner seal and outer
continuous grease purge is never a problem. seal. These components work in tandem to form an
extremely effective sealing system. (See page 5 for more
Advantages of the HDi Series:
details.)
• Complete ZMaRC coating on all housing surfaces for
The added strength and durability of the Marathon
long-term corrosion resistance.
HDi housings make them particularly well suited for
• ZMaRC coating will not flake off. applications in red meat, pork and poultry processing
facilities where both housing strength and corrosion
• Housings and bearings are resistant to the majority of
resistance are a concern.
common washdown solutions.
The HDi Series is available in the following
• HDi units require no relubrication, even in a washdown
housing designs:
environment—saving time and money—while
providing a cleaner-running unit. – pillow blocks
– two- or four-bolt flange
– tapped base
387
MRC Bearing Services
388
BEARING
INTRODUCTION ENGINEERING DATA MARATHON SERIES MADE-TO-ORDER
SPECIFICATION TABLES
Made-To-Order
Solutions from MRC
Order publication #M200-111
MRC Bearing Services
MRC’s MTO group has the technical expertise and wide bearing
industry experience to help identify and source the hard-to-find,
discontinued or special products you need. With manufacturing and
rework/modification capabilities covering virtually all ball bearing
designs and size ranges, MTO can satisfy your special or custom Heat treatment
needs often in lot sizes as small as one! In addition, our flexible rework
capabilities allow MTO to meet your tight time frame restrictions.
MRC Engineering
• Applications engineering reviews all MTO requests for application
suitability and assignment of proper engineering specifications.
• Application engineering has extensive experience in bearing
lubrication (low and high temperature, food grade, solid oil),
materials (standard bearing steel, stainless steels, M50 steel, and
ceramics), and all ball bearing designs in order to specify the most
appropriate bearing solution to meet your needs. Lubrication
MRC Commitment
• All MTO reworked and modified products are done according to
MRC’s rigid standards and practices and are therefore sold with the
same original manufacturer’s warranty as our standard product.
Design flexibility
389
MRC Bearing Services
Capabilities
Bearing Designs
MTO Product offers a broad range of single and double row ball bearing
designs, including:
• Inch Dimension – R, XLS, LS, MS Series
• Thin Section – 1800 and 1900 Series
• Single Row Deep Groove – S Type
• Single Row Max Type – M Type
• Single Row 15° Angular Contact – R type
• Single Row Angular Contact – 7000, 7000P and 7000PJ Series
• Single Row Angular Contact Split Ring – 9000 and 9000P Series
• PumPac® 8000 Series
Cage designs • Double Row Angular Contact – 5000 Series
• Self-aligning Ball Bearings
• Hybrid (Ceramic) Ball Bearings
• Precision Grades to ABEC 7 +
• Custom Designed Product
390
MRC Bearing Services
Headquarters
1510 Gehman Road
Kulpsville, PA 19443
USA
Engineering Handbook