Professional Documents
Culture Documents
Huawei WLAN AP Antenna Datasheet
Huawei WLAN AP Antenna Datasheet
www.huawei.com
Antenna Description
WLAN antennas are described as follows:
Polarization
WLAN antennas are classified into single-polarized and dual-polarized antennas by polarization. A single-polarized antenna has
one radio port, and a dual-polarized antenna has two.
Antenna gain
Antenna gain is a key parameter for measuring the coverage capability of an antenna. For the same type of antennas, a higher-
gain antenna supports a higher coverage distance and better effect.
Radiation
WLAN antennas support omnidirectional and directional radiation patterns. Omnidirectional antennas are applicable to indoor
coverage scenarios, and directional antennas to outdoor coverage scenarios. Directional antennas can also be deployed
indoors, such as large convention centers, conference centers, airports, and stations.
Beamwidth
An antenna has horizontal beamwidth and vertical beamwidth, forming a horizontal lobe angle and a vertical lobe angle,
respectively. In most cases, the beamwidth is the angular separation between the points in the main lobe where the radiated
power has fallen by 3 dB (half-power) below that on the center line of the lobe. The beamwidth is also called the half-power
beamwidth.
Installation mode
Antennas can be directly connected to APs or mounted on a wall, ceiling, or pole. The pole mounting mode is the mainstream
mode.
Selection Policy
Overview
Before determining an AP model and antenna, consider the basic principles and port types of APs and antennas.
Basic principles
1 Usage scenario and Indoor scenarios: Use indoor APs and antennas to provide signal coverage.
purpose Outdoor scenarios: Use outdoor APs and antennas with a high Ingress Protection
(IP) grade and certain surge protection capability to provide signal coverage and
bridge backhaul.
Rail transportation scenarios:
− Train-ground communications: Use outdoor APs and antennas with a high IP
grade and certain anti-vibration capability.
− Compartment coverage: Use indoor APs and antennas with certain anti-
2 Local standards and The transmit power and maximum gain of antennas must strictly comply with local
regulations standards and regulations. For the rail transportation scenarios, the performance,
environment adaptability, and anti-vibration capability of the antennas must also
confirm to requirements of the related railway authorities.
3 Coverage/Backhaul area Coverage: Directional antennas are recommended for long and narrow areas while
and distance omnidirectional antennas are recommended for round and square areas.
Backhaul: Directional antennas are usually used. If the backhaul distance is long,
high-gain antennas should be used; if the backhaul target is concentrated, small-
angle antennas should be used.
4 Transmission frequency Coverage: To implement 2.4 GHz and 5 GHz signal coverage, use 2.4 GHz and 5
for radio signals GHz antennas separately in the same area or use dual-band antennas.
Backhaul: The 2.4 GHz antennas are not used for backhaul.
5 Construction cost and An external directional antenna usually has a large size and needs to be connected to
simplicity the AP's radio port through a feeder cable. Compared to a built-in antenna and whip
antenna directly installed on an AP, installing an external directional antenna requires
higher construction costs and may affect indoor decoration. To further simplify cable
layout (especially in coverage scenarios) without compromising signal quality, you are
advised to use built-in or directly install whip antennas on APs.
7 Outdoor dual-band 27013718 4 x Type-N female/dual- 13 dBi & 16 33°/33° & 18°/18°
directional antenna band dBi
Technical Specifications
Technical specifications of the 27011172 omnidirectional antenna
Gain (dBi) 3 4
Connector RP-SMA-J
Weight (g) 12
The coverage distance is a reference value in certain conditions. Plan an appropriate distance value according to planning
experience, local standards, and onsite environments.
There may be differences in the standards of different countries, so the mapping between antennas and APs shall comply with
local standards. For details, refer to network access certification information about devices.
The coverage distance is subject to the following constraints:
The default AP transmit power is 15 dBm.
The default STA type is mobile phone, and no obstacle exists.
2.4 GHz: The uplink and downlink RSSIs are greater than or equal to -70 dBm.
5 GHz: The uplink and downlink RSSIs are greater than or equal to -75 dBm.
For any questions about the parameters above, contact Huawei technical support.
27012545 Indoor 2.4 GHz & 5 GHz Omnidirectional Antenna (H360 V110 G4 &
H360 V110 G5)
The 27012545 omnidirectional antenna is named ANTDG0404D4SR and applicable to indoor scenarios with aesthetic
requirements.
Technical Specifications
Technical specifications of the 27012545 omnidirectional antenna
Gain (dBi) 4 5
Connector 4 x RP-SMA-J
The coverage distance is a reference value in certain conditions. Plan an appropriate distance value according to planning
experience, local standards, and onsite environments.
There may be differences in the standards of different countries, so the mapping between antennas and APs shall comply with
local standards. For details, refer to network access certification information about devices.
The coverage distance is subject to the following constraints:
The default AP transmit power is 15 dBm.
The default STA type is mobile phone, and no obstacle exists.
2.4 GHz: The uplink and downlink RSSIs are greater than or equal to -70 dBm.
5 GHz: The uplink and downlink RSSIs are greater than or equal to -75 dBm.
For any questions about the parameters above, contact Huawei technical support.
Technical Specifications
Technical specifications of the 27010215 omnidirectional antenna
Item Value
Gain (dBi) 11
Connector N-female
The coverage distance is a reference value in certain conditions. Plan an appropriate distance value according to planning
experience, local standards, and onsite environments.
There may be differences in the standards of different countries, so the mapping between antennas and APs shall comply with
local standards. For details, refer to network access certification information about devices.
The coverage distance is subject to the following constraints:
The default AP transmit power is 15 dBm.
The default STA type is mobile phone, and no obstacle exists.
2.4 GHz: The uplink and downlink RSSIs are greater than or equal to -70 dBm.
For any questions about the parameters above, contact Huawei technical support.
Antenna Appearance
Appearance of the 27013721 omnidirectional antenna
Technical Specifications
Technical specifications of the 27013721 omnidirectional antenna
Gain (dBi) 4 7
Connector N-male
Weight (g) 90
Technical Specifications
Technical specifications of the 27011668 antenna
Gain (dBi) 4 7
Connector N-male
The coverage distance is a reference value in certain conditions. Plan an appropriate distance value according to planning
experience, local standards, and onsite environments.
There may be differences in the standards of different countries, so the mapping between antennas and APs shall comply with
local standards. For details, refer to network access certification information about devices.
The coverage distance is subject to the following constraints:
The default AP transmit power is 15 dBm.
The default STA type is mobile phone, and no obstacle exists.
2.4 GHz: The uplink and downlink RSSIs are greater than or equal to -70 dBm.
For any questions about the parameters above, contact Huawei technical support.
Antenna Appearance
Appearance of the 27013571 antenna
Technical Specifications
Technical specifications of the 27013571 directional antenna
Item Value
Gain (dBi) 18
Connector 2 x N-female
The coverage distance is a reference value in certain conditions. Plan an appropriate distance value according to planning
experience, local standards, and onsite environments.
There may be differences in the standards of different countries, so the mapping between antennas and APs shall comply with
local standards. For details, refer to network access certification information about devices.
The coverage distance is subject to the following constraints:
The default AP transmit power is 15 dBm.
The default STA type is mobile phone, and no obstacle exists.
2.4 GHz: The uplink and downlink RSSIs are greater than or equal to -70 dBm.
For any questions about the parameters above, contact Huawei technical support.
Antenna Appearance
Appearance of the 27010812 directional antenna
Technical Specifications
The following table lists technical specifications of the 27010812 directional antenna.
Item Value
Gain (dBi) 12
Connector 2 x N-female
The coverage distance is a reference value in certain conditions. Plan an appropriate distance value according to planning
experience, local standards, and onsite environments.
There may be differences in the standards of different countries, so the mapping between antennas and APs shall comply with
local standards. For details, refer to network access certification information about devices.
The coverage distance is subject to the following constraints:
The default AP transmit power is 15 dBm.
27010904 Outdoor 2.4 GHz Dual-Polarized Directional Antenna (H30 V30 G14)
The 27010904 antenna is an outdoor 2.4 GHz directional antenna. To obtain better performance and wider coverage, the
antenna should be installed at high positions away from metal obstacles, for example, building tops, mountaintops, and tower
tops. Its transmit end should not be blocked by obstacles.
Antenna Appearance
The following figure shows the appearance of the 27010902 directional antenna.
Technical Specifications
The following table lists technical specifications of the 27010219 directional antenna.
Item Value
Gain (dBi) 14
Connector 2 x N-female
The coverage distance is a reference value in certain conditions. Plan an appropriate distance value according to planning
experience, local standards, and onsite environments.
There may be differences in the standards of different countries, so the mapping between antennas and APs shall comply with
local standards. For details, refer to network access certification information about devices.
The coverage distance is subject to the following constraints:
The default AP transmit power is 15 dBm.
The default STA type is mobile phone, and no obstacle exists.
2.4 GHz: The uplink and downlink RSSIs are greater than or equal to -70 dBm.
For any questions about the parameters above, contact Huawei technical support.
Antenna Appearance
Appearance of the 27010664 antenna
Technical Specifications
Technical specifications of the 27010664 directional antenna
Item Value
Gain (dBi) 18
Connector 4 x N-female
Weight (kg) 11
The coverage distance is a reference value in certain conditions. Plan an appropriate distance value according to planning
experience, local standards, and onsite environments.
There may be differences in the standards of different countries, so the mapping between antennas and APs shall comply with
local standards. For details, refer to network access certification information about devices.
The coverage distance is subject to the following constraints:
The default AP transmit power is 15 dBm.
The default STA type is mobile phone, and no obstacle exists.
2.4 GHz: The uplink and downlink RSSIs are greater than or equal to -70 dBm.
For any questions about the parameters above, contact Huawei technical support.
In bridging scenarios, installation positions should not exceed wireless bridge transmission distances.
Technical Specifications
Technical specifications of the 27010906 directional antenna
Item Value
Gain (dBi) 14
Connector 2 x N-female
The coverage distance is a reference value in certain conditions. Plan an appropriate distance value according to planning
experience, local standards, and onsite environments.
There may be differences in the standards of different countries, so the mapping between antennas and APs shall comply with
local standards. For details, refer to network access certification information about devices.
The coverage distance is subject to the following constraints:
The default AP transmit power is 15 dBm.
The default STA type is mobile phone, and no obstacle exists.
2.4 GHz: The uplink and downlink RSSIs are greater than or equal to -70 dBm.
For any questions about the parameters above, contact Huawei technical support.
In bridging scenarios, installation positions should not exceed wireless bridge transmission distances.
Antenna Appearance
Appearance of the 27010889 directional antenna
Technical Specifications
Technical specifications of the 27010889 directional antenna
Item Value
Connector 2 x N-female
The coverage distance is a reference value in certain conditions. Plan an appropriate distance value according to planning
experience, local standards, and onsite environments.
There may be differences in the standards of different countries, so the mapping between antennas and APs shall comply with
local standards. For details, refer to network access certification information about devices.
The coverage distance is subject to the following constraints:
The default AP transmit power is 15 dBm.
The default STA type is mobile phone, and no obstacle exists.
2.4 GHz: The uplink and downlink RSSIs are greater than or equal to -70 dBm.
For any questions about the parameters above, contact Huawei technical support.
In bridging scenarios, installation positions should not exceed wireless bridge transmission distances.
Technical Specifications
Technical specifications of the 27010890 directional antenna
Item Value
Gain (dBi) 19
Connector 2 x N-female
The coverage distance is a reference value in certain conditions. Plan an appropriate distance value according to planning
experience, local standards, and onsite environments.
There may be differences in the standards of different countries, so the mapping between antennas and APs shall comply with
local standards. For details, refer to network access certification information about devices.
The coverage distance is subject to the following constraints:
The default AP transmit power is 15 dBm.
The default STA type is mobile phone, and no obstacle exists.
2.4 GHz: The uplink and downlink RSSIs are greater than or equal to -70 dBm.
Antenna Appearance
Appearance of the 27013413 antenna
Item Value
Connector 2 x N-female
The coverage distance is a reference value in certain conditions. Plan an appropriate distance value according to planning
experience, local standards, and onsite environments.
There may be differences in the standards of different countries, so the mapping between antennas and APs shall comply with
local standards. For details, refer to network access certification information about devices.
The coverage distance is subject to the following constraints:
The default AP transmit power is 15 dBm.
The default STA type is mobile phone, and no obstacle exists.
5 GHz: The uplink and downlink RSSIs are greater than or equal to -75 dBm.
For any questions about the parameters above, contact Huawei technical support.
Antenna Appearance
Appearance of the 27013921 antenna
Technical Specifications
Technical specifications of the 27013921 directional antenna
Item Value
Connector N-female x 2
The coverage distance is a reference value in certain conditions. Plan an appropriate distance value according to planning
experience, local standards, and onsite environments.
There may be differences in the standards of different countries, so the mapping between antennas and APs shall comply with
local standards. For details, refer to network access certification information about devices.
The coverage distance is subject to the following constraints:
The default AP transmit power is 15 dBm.
The default STA type is mobile phone, and no obstacle exists.
5 GHz: The uplink and downlink RSSIs are greater than or equal to -75 dBm.
For any questions about the parameters above, contact Huawei technical support.
Technical Specifications
Technical specifications of the 27013955 directional antenna
Item Value
Gain (dBi) 16
Connector 4 x N-female
The coverage distance is a reference value in certain conditions. Plan an appropriate distance value according to planning
experience, local standards, and onsite environments.
There may be differences in the standards of different countries, so the mapping between antennas and APs shall comply with
local standards. For details, refer to network access certification information about devices.
The coverage distance is subject to the following constraints:
The default AP transmit power is 15 dBm.
The default STA type is mobile phone, and no obstacle exists.
5 GHz: The uplink and downlink RSSIs are greater than or equal to -75 dBm.
For any questions about the parameters above, contact Huawei technical support.
Antenna Appearance
Appearance of the 27013956 antenna
Technical Specifications
Technical specifications of the 27013956 directional antenna
Item Value
Gain (dBi) 16
Connector 4 x N-female
The coverage distance is a reference value in certain conditions. Plan an appropriate distance value according to planning
experience, local standards, and onsite environments.
There may be differences in the standards of different countries, so the mapping between antennas and APs shall comply with
local standards. For details, refer to network access certification information about devices.
The coverage distance is subject to the following constraints:
The default AP transmit power is 15 dBm.
The default STA type is mobile phone, and no obstacle exists.
5 GHz: The uplink and downlink RSSIs are greater than or equal to -75 dBm.
For any questions about the parameters above, contact Huawei technical support.
Antenna Appearance
Appearance of the 27013718 antenna
Technical Specifications
Technical specifications of the 27013718 antenna
Gain (dBi) 13 16
Connector 4 x N-female
The coverage distance is a reference value in certain conditions. Plan an appropriate distance value according to planning
experience, local standards, and onsite environments.
There may be differences in the standards of different countries, so the mapping between antennas and APs shall comply with
local standards. For details, refer to network access certification information about devices.
The coverage distance is subject to the following constraints:
The default AP transmit power is 15 dBm.
The default STA type is mobile phone, and no obstacle exists.
2.4 GHz: The uplink and downlink RSSIs are greater than or equal to -70 dBm.
5 GHz: The uplink and downlink RSSIs are greater than or equal to -75 dBm.
For any questions about the parameters above, contact Huawei technical support.
27013719 Outdoor 2.4 GHz & 5 GHz Dual-Polarized Directional Antenna (H33
V33 G13 & H30 V30 G13)
The 27013719 directional antenna is named ANTDG1313D4NR and mainly applicable to outdoor road, wireless backhaul, and
high-density stadium scenarios.
Antenna Appearance
Appearance of the 27013719 antenna
Gain (dBi) 13 13
Connector 4 x N-female
The coverage distance is a reference value in certain conditions. Plan an appropriate distance value according to planning
experience, local standards, and onsite environments.
There may be differences in the standards of different countries, so the mapping between antennas and APs shall comply with
local standards. For details, refer to network access certification information about devices.
The coverage distance is subject to the following constraints:
The default AP transmit power is 15 dBm.
The default STA type is mobile phone, and no obstacle exists.
2.4 GHz: The uplink and downlink RSSIs are greater than or equal to -70 dBm.
5 GHz: The uplink and downlink RSSIs are greater than or equal to -75 dBm.
For any questions about the parameters above, contact Huawei technical support.
27013720 Outdoor 2.4 GHz & 5 GHz Dual-Polarized Directional Antenna (H70
V70 G8 & H70 V70 G8)
The 27013720 directional antenna is named ANTDG0808D4NR and applicable to outdoor wide-coverage scenarios.
Technical Specifications
Technical specifications of the 27013720 antenna
Gain (dBi) 8 8
Connector 4 x N-female
The coverage distance is a reference value in certain conditions. Plan an appropriate distance value according to planning
experience, local standards, and onsite environments.
There may be differences in the standards of different countries, so the mapping between antennas and APs shall comply with
local standards. For details, refer to network access certification information about devices.
The coverage distance is subject to the following constraints:
The default AP transmit power is 15 dBm.
The default STA type is mobile phone, and no obstacle exists.
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or
part of the products, services and features described in this document may not be within the purchase scope or the usage
scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are
provided "AS IS" without warranties, guarantees or representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the preparation of this
document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not
constitute a warranty of any kind, express or implied.
Address: Huawei Industrial Base Bantian, Longgang Shenzhen 518129 People's Republic of China
Website: www.huawei.com