Professional Documents
Culture Documents
Bamboo Joints and Joinery Techniques
Bamboo Joints and Joinery Techniques
Bamboo Joints and Joinery Techniques
Do not use green, fresh cut bamboo. Bamboo has to be completely dry before using it in construction
(preferable air dried). During the drying process the bamboo diameter shrinks, so when bamboo is used in
joinery this will result in lose and weak joints after a few weeks.
Do not use bamboo when it is less then 3 years of age. Only use mature bamboo of 4-6 years.
Do not use bamboo infected by insects (powder beetle for example). Bamboo has to be properly cured with
a boron mix immediately after harvesting.
Do not use bamboo that has flourished. Rest assured bamboo only flourishes once in a lifetime (60-120
years).
Do not use bamboo poles with profound vertical cracks.
Use appropriate cuts and joints when building with bamboo.
Use bamboo with the right diameter and wall thickness for your project.
Do not use conventional wood nails in bamboo joinery, they will cause the bamboo to split. Instead use
nylon, steel or vegetal cord of the appropriate diameter.
When using bamboo as a column make sure that the lower part connecting with the surface ends with a
node. If not the bamboo will splinter when struck (for example to position the column).
When connecting bamboo poles with bolts, make sure to bolt them together in between 2 nodes, otherwise
the bamboo may crush. More about utilizing the nodes below...
In construction, using bamboo nodes is very important. Bamboo columns or beams need to have a node at both
ends (or as close as possible towards the ends), if not the pressure of a structure on the joint may crush the bamboo.
Often it isn't possible to find bamboo of the required length with both end nodes in place. When this occurs you
should insert a wooden cylinder of the appropriate diameter or a fitting piece of bamboo with a node.
Bamboo Cuts
These are the most common cuts to use when making bamboo joints:
one ear / two ear / beveled / flute mouth / fish mouth
As you can see in the illustration below, making basic cuts in bamboo doesn't require expensive or heavy power tools,
just a few traditional hand tools will work fine.
Bamboo Joinery Techniques
Making good and aesthetically pleasing bamboo joints is rather complicated because bamboo is hollow, tapered, has
nodes at varying distances, and it is not perfectly circular. It is important to keep all these constraints in mind when
designing a bamboo joint.
Although traditions, local practices and publications give some information on bamboo joinery, this information is far
from complete as essential data is missing in most cases. Many traditional joinery techniques suffer from weakness or
deformation, where the strength of the bamboo culm itself is lost.
Before bamboo gets widely adopted in modern architecture (and becomes affordable for all to use), the problem with
bamboo joints and universal joining systems has to be solved. After all, timber, steel, and more recently prefabricated
concrete, only became proper building materials for the same reasons. How many cumbersome solutions for joints
have one seen, before these materials became a standard in construction?
Only if the problem with bamboo joinery can be satisfactorily addressed, and simplified, we can expect to see much
more bamboo in Western buildings, bridges and furniture.
Below you'll find some examples and illustrations of traditional bamboo joinery techniques.
Joining horizontal with vertical elements
1. Joint with one or two ears. Is used to join bamboo rafters, logs or lumber.
4. Flap joint. Is used when there is no lashing wire available. The flap can be secured with bamboo strips.
5. Fish mouth joint.
Use of dowels and anchors in bamboo joinery
1. Joining bamboo with dowels and lashing. The peg should be placed in the column parallel to the rafter.
1. Beams formed by 4 or 6 members. The top row is separated from the bottom with bamboo or wood slats so that
the upper bamboos do not slide over the lower.
2. Central double rafter. It has a wide range of applications in the construction of bridges and structures for rural
facilities.
3. Lateral double rafter. Each of the rafters is secured independently at the side support and each other. It is often used
in the construction of bridges and structures for rural facilities.
4. Lateral double rafters. Is often used as a central support for bridge structures or sheds.
1. Top splicing.
2. Bevel splicing.
3. Ray splicing
7. Telescope splicing.