Professional Documents
Culture Documents
FW Pipe Specs
FW Pipe Specs
FW Pipe Specs
26160-000-50A10
PIPING MATERIAL FOSTER WHEELER SOUTH AFRICA (PTY) LTD PAGE 1 OF 353
SPECIFICATION ENGINEERING STANDARD REV F3
REVISION F1 F2 F3
Signature Signature Signature
DATE 20/09/10 07/04/11 20/02/12
ORIG. BY G. GEHANI G.G. G. GEHANI G.G. G. GEHANI G.G.
APP. BY H. BOTHMA H.B. H. BOTHMA H.B. H. BOTHMA H.B.
QA REVIEW S. CAHILL S.C.
CONTENTS
REVISION HISTORY
REVISION DESCRIPTION
F3 Additional items included in line classes.
A1 1st Issue.
W:\Project\Sasol\26160\Gen\08Eng\056pipspec\Piping Material
Specification\Rev F3_201202\00 26160-000-50A10 Rev F3.doc DSN: 10217
SASOL SPECIFICATION SP-50-3A
REVISION 7
PREVIOUS REVISIONS
ISSUE
REV No PROPOSED BY REVIEWED BY APPROVED BY DATE
DATE
VALIDATION This Specification is only regarded as controlled in the electronic format on the official Sasol Livelink/Intranet website.
When printed, this document is deemed as uncontrolled and thus for information only. It is the responsibility of the user of a printed copy of
the document to ensure validity before use. When issued on a CD to a registered user, it is a controlled document and users will be notified
and issued with the latest revision. If it is issued for a specific project, it is valid for the duration of the project, unless agreed otherwise.
COPYRIGHT This Specification is protected by copyright and is the sole property of Sasol. The information is proprietary to Sasol and
is for the sole use of the identified project or defined scope of work. Any unauthorised use, disclosure or copying or any other means of
duplication or reproduction, is prohibited.
Copyright © 2007. Sasol. All rights reserved.
Revision 7
July 2007
Page i of iv
Copyright © 2007. Sasol. All rights reserved.
Revision 7
July 2007
REVISION SHEET
REVISION 7
8. Branch Table D removed and Table E renamed to Table D – general revision done on tables
9. Line Class A and N socket weld ranges changed from NPS ½ - NPS 1½ to NPS ½ - NPS 1
10. Spiral wound gaskets are now given as another option in all the Class 150 and 300 line classes
Page ii of iv
Copyright © 2007. Sasol. All rights reserved.
Revision 7
July 2007
TABLE OF CONTENTS
PAGE
2.1 VALVES..................................................................................................................... 8
2.2 PIPE .......................................................................................................................... 11
2.3 FITTINGS................................................................................................................. 12
2.4 FLANGES................................................................................................................. 13
2.5 FLANGE FINISH ..................................................................................................... 14
2.6 LINE REDUCTIONS ............................................................................................... 14
2.7 SEAL WELDING ..................................................................................................... 14
2.8 PIPE BENDS ............................................................................................................ 15
2.9 THREAD COMPOUND........................................................................................... 15
2.10 WELD EXAMINATION.......................................................................................... 16
2.11 BRANCH CONNECTIONS..................................................................................... 16
2.12 BOLTING ................................................................................................................. 17
2.13 GASKETS................................................................................................................. 17
Page iii of iv
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION GENERAL NOTES
PAGE
APPENDICES
APPENDIX A BOLTING
Page iv of iv
Copyright © 2007. Sasol. All rights reserved.
Revision 7
July 2007
1.1.1 This Specification is based on ASME B31.3. Piping systems according to ASME B31.1 are
also covered in the line classes. All line classes conform to the requirements of the
Occupational, Health and Safety Act of the Republic of South Africa (Act 85 of 1993), as
applicable.
1.1.2 Pressure temperature ratings for Class 150 and higher flanged components NPS ½ to NPS 24
are based on ASME B16.5. Pressure-temperature ratings for flanged components larger than
NPS 24 are specified in ASME B16.47.
1.1.3 Unless otherwise specified, all piping component wall thicknesses are based only on design
considerations of internal pressure, temperature, and allowances for corrosion, erosion,
manufacturer’s minus tolerance and any allowance for the depth of threads or grooves. It
does not include any additional thickness that may be required to compensate for such design
considerations as external pressure, thermal loads due to restraints, live loads, hydraulic
shock, or loads and forces from other causes, all of which shall be considered in the design
of piping systems.
1.1.4 Conversion factors for units and measurements shall be in accordance with Specification
SP-90-31.
Page 1 of 21
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION GENERAL NOTES
1.2.1 The item descriptions used in the individual line classes are abbreviated and shall not be used
for purchasing.
1.2.2 Comprehensive purchase descriptions are given in the Piping Material Commodities
Catalogue by item code number.
1.2.3 Additional specific requirements for purchased components are covered in Specifications
SP-50-10 to SP-50-13, SP-50-15 and SP-50-25.
1.2.4 Like components shall have the same item code number whether full size or reducing (full
size tees and reducing tees, full size elbows and reducing elbows, etc.).
Items specified or referenced by manufacturer and figure number illustrates typical required
quality features and are not intended to exclude equal items offered by other manufacturers.
1.4.1 Unless otherwise specified, pressure and temperature refer to design conditions.
Page 2 of 21
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION GENERAL NOTES
1.4.2 Services listed in the individual line classes as corrosive or non-corrosive (oil, vapour, or
gas) hydrocarbons, hydrogen, or mixtures of hydrocarbons and hydrogen are defined as
follows:
c. Non-corrosive hydrocarbon streams are defined as those streams with a corrosion rate
not greater than 1 mm in 10 years.
d. Corrosive hydrocarbon streams are defined as those streams with a corrosion rate
greater than 1 mm in 10 years. Corrosive hydrocarbon streams are defined as a
specific service in the individual line classes.
e. Where specific design limitations (temperature, pressure, velocity, etc.) have been
established, the stream, either corrosive or non-corrosive, and the design limitations,
shall be defined in the individual line class.
1.4.3 The selection of steels exposed to hydrogen service shall be in accordance with Appendix E.
Hydrogen service is defined as any service containing hydrogen in which the hydrogen
partial pressure at the design temperature exceeds 600 kPa (abs) except that when the design
temperature is below 150°C, the hydrogen partial pressure must be higher than
1000 kPa (abs).
1.4.4 Material selection for streams containing caustic soda shall be in accordance with
Appendix D.
Page 3 of 21
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION GENERAL NOTES
a. Sour gas
Gas services containing hydrogen sulphide at a partial pressure greater than 345 Pa
shall be considered as sour gas services.
Low pressure gas systems containing hydrogen sulphide are not considered to be in
sour service if the total pressure of the system is below 450 kPa.
b. Sour water
In water systems the service is defined as sour water when the hydrogen sulphide
content of the water exceeds 10 ppm.
Multiphase systems consisting of oil and gas, or oil, water and gas operating at
450 kPa to 1825 kPa shall be defined as sour if the system contains hydrogen sulphide
at a partial pressure of 69 kPa and higher or if the gas phase contains more than 15%
hydrogen sulphide. At operating pressure above 1825 kPa the system is defined as
sour when the hydrogen sulphide partial pressure exceeds 345 Pa. See Figure AC
Appendix C.
1.4.7 The selection of steels exposed to process streams containing hydrogen sulphide at
temperatures above 200°C shall be in accordance with Appendix F.
1.4.8 Selection of materials for use in hydrofluoric service shall be in accordance with
Appendix G.
1.5.1 Piping components smaller than NPS ½ shall not be used except when required for
connections to equipment.
Page 4 of 21
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION GENERAL NOTES
1.5.2 Piping components NPS 1¼, NPS 2½, NPS 3½, NPS 5 and NPS 7 shall not be used.
1.5.3 Piping for vents, drains, sample connections and level instruments shall be in accordance
with Drawing STDD-5059.
Except where unions or flanges are required or as otherwise specified in the individual line
classes, pipe-to-pipe joints shall be made in accordance with the following:
1.7.1 Machine bolt length shall be measured from the bearing surface of the head to the extreme
point.
1.7.2 Stud bolt length shall be the effective thread length, excluding end points.
1.8.1 Valves, Y-strainers, and special piping items shall be furnished with a metal tag attached,
bearing the applicable item code number.
Page 5 of 21
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION GENERAL NOTES
1.8.2 Tags for locked open valves shall be stamped “THIS VALVE SHALL NOT BE CLOSED
WITHOUT THE WRITTEN PERMISSION OF ” fill in the job title of
the responsible person) and painted green. Tags for locked close valves shall be stamped
“THIS VALVE SHALL NOT BE OPENED WITHOUT THE WRITTEN PERMISSION
OF ” (fill in the job title of the responsible person) and painted red.
1.8.3 Individual lengths of pipe shall be identified with the applicable item code number, in
accordance with the following:
b. Numbers shall be applied with a Pannier Model T55 hand bar and tube printer, or
SASOL approval equal with E-Z set printing wheel and 6,35 mm changeable dies.
The marking ink shall be Pannier 1001 Yellow Industrial ink.
c. Galvanised steel, cast iron, or non-metallic alloy shall normally be exempt from this
requirement.
Colour coding is a means of alerting construction that the material is alloy or otherwise
special. Reference shall be made to the manufacturer's markings to determine the exact type
of material. Colour coding of pipe, fittings and flanges shall be as specified in Appendix H.
1.10.1 When it is necessary to use a piping component which is not specified in the relevant line
class, the component shall be selected from the Piping Material Commodities Catalogue.
1.10.2 If the required component does not appear in the Piping Material Commodities Catalogue, a
new item code number shall be assigned and a full purchase description shall be added to the
Catalogue. These items shall be listed on Data Sheet E479. New items shall not be added to
the catalogue without written approval from SASOL.
Page 6 of 21
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION GENERAL NOTES
1.10.3 All components not specified in the line classes, shall be identified on flow diagrams and
drawings with the applicable item code number.
1.10.4 Unless otherwise specified, filters in oxygen service shall have monel elements with a sieve
designation of 150 µm.
1.11.1 The corrosion allowance is specified in each individual line class in millimetres.
1.11.2 Corrosion allowance different from that listed in the individual line classes shall be indicated
on the flow diagrams and listed on Data Sheet E693.
Buried steel piping shall be externally protected in accordance with Specification SP-50-6.
Fabrication, installation, and testing of piping systems shall be in accordance with the
following:
1.13.2 Cleaning and internal protection of carbon steel piping - Specification SP-50-5.
Page 7 of 21
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION GENERAL NOTES
1.14 STRAINERS
All strainers NPS 2 and larger shall be designed for the actual service conditions.
When in an individual line class it is specified that “...all lines must be calculated for the
individual design conditions...”, wall thickness calculations shall be based on the lowest
strength component in the system.
The following notes serve to amplify the requirements specified in an individual line class.
2.1 VALVES
B. Deleted.
C. Globe valves larger than those specified in the individual line classes are permitted.
However, such valves shall be individually reviewed for possible geared operation
and, if required, the valve shall be identified as a specialty item on flow diagram(s).
Page 8 of 21
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION GENERAL NOTES
D. Manual gear operators, as furnished by the valve manufacturer, shall be provided for
all gate, globe and lubricated or sleeved plug valves, in accordance with the following:
G. For manual operation of all valves, the force required at the hand wheel or wrench
shall not exceed 270 N.
2. At battery limits in utility and cooling water supply and return lines.
3. At battery limits in outgoing product lines when the valves are required to divert
product streams.
All such valves shall be steel valves and shall be indicated on flow diagrams and
drawings.
Page 9 of 21
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION GENERAL NOTES
When valves are required to be insulated, at design temperatures greater than 400°C,
the bonnet bolting shall be specified for the temperature and the valve shall be
identified on the flow diagrams and drawings with the applicable item code number.
See also Appendix A.
J. Flanged valves, Class 600 minimum rating shall be fitted against flanged connections
NPS 1½ and smaller to tanks, vessels and equipment.
L. Check valves may be installed in the vertical (upward flow) or horizontal position
unless limited by the item description in the individual line class. Dual plate type
check valves shall be installed with their shafts in the vertical position in horizontal
lines.
1. Gate valves in steam or water service: locations “A” and “G” and shall have
openings machined for a socket welding connection.
2. Conventional swing check valves in steam or water service: location “G” and
shall have openings machined for a socket welding connection.
Page 10 of 21
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION GENERAL NOTES
N. Socket welded valves having a non-metallic seat, disc, or seal material may require
that the individual seat, disc, or seal (or the part containing the plug or seal) be
removed, in accordance with the manufacturer's recommendations, prior to welding
the valve into the line.
O. Valves with extended bonnet design shall be installed with the stem in the vertical
position. Valves with extended bonnet may be installed with the stem below the
vertical position only when approved by SASOL.
P. Valves with extended bonnet design shall have modified back-seating to allow venting
of the bonnet cavity when the valve is in the open position. Such valves cannot be
repacked under pressure.
Q. Flare line isolation valves shall be installed with their spindles vertically down.
2.2 PIPE
B. When the individual line class requires that pipe wall thicknesses be calculated, the
selected wall thicknesses shall be indicated on the flow diagrams, drawings, and listed
on Data Sheet E693.
C. When an individual line requires a pipe wall thickness greater than that specified in an
individual line class or as indicated on the flow diagram, in order to compensate for
such design considerations as thermal loads due to restraints (See Paragraph 1.1.3 of
these General Notes), the selected wall thickness shall be indicated on the flow
diagram, drawings, and listed on Data Sheet E0693.
Page 11 of 21
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION GENERAL NOTES
D. When welded seam pipe, with a longitudinal weld joint Factor E of less than 1,00 has
been specified in an individual line class as the “MINIMUM THICKNESS
PERMITTED”, the pipe wall thickness shall be calculated:
1. using the longitudinal weld joint factor specified in the line class,
If the cost of the piping resulting from basis 2 is more economical than basis 1 piping,
the higher quality pipe with the lesser nominal wall thickness shall be selected.
2.3 FITTINGS
B. Lap-joint stub ends shall have the same facing as that specified for flanges in the
individual line classes.
C. When the thickness of butt welding fittings is specified as “wall thickness to match
pipe”, fittings of commercially available schedules (weight or thickness) shall be used
even though the wall thickness of such fittings may be slightly greater than the mating
pipe. In such cases, the butt welding ends of fittings shall be taper bored in
accordance with ASME B16.25 when the fitting thickness exceeds the mating pipe
wall thickness by more than 1,5 mm. When taper boring of butt welding fittings
would result in a reduction of the minimum allowable wall thickness, the design shall
be approved by SASOL and the details for connecting the fitting to the mating pipe
shall be shown on the isometric pipe drawing.
D. Unless when specified in the individual line classes, mitres shall not be permitted
without SASOL’s approval. When permitted mitres shall be in accordance with
Drawing STDD-5037.
Page 12 of 21
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION GENERAL NOTES
F. Threaded fittings may be used for open end vent and drain piping downstream of
block valves.
G. Deleted.
H. Butt welding reducing fittings shall have all ends specified to the same schedule
(weight or thickness). The schedule specified shall not be less than that required by
the line class.
I. Where swage nipples or butt welding reducers are specified in an individual line class,
the sizes indicated in the “SIZE” column shall be as follows:
2.4 FLANGES
B. Only weld neck flanges shall be used in NPS 2 and larger lines in hydrogen service.
When slip-on flanges are approved by SASOL for use in hydrogen service, the
enclosed space between the outside diameter of the pipe and the inside bore of the
flange shall be vented by drilling a 3 mm hole through the flange hub.
Page 13 of 21
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION GENERAL NOTES
C. Flanges fabricated from plate are not permitted without prior approval by SASOL.
D. When steel flanges are bolted to flat face flanges conforming to ASME B16.1,
ASME B16.24, MSS-SP-42 or MSS-SP-51, the steel flanges shall be flat face.
A. When a “raised face smooth finish” (RFSF) facing is specified, the gasket contact
surface roughness shall be 1,6 µm Ra to 3,2 µm Ra in accordance with ASME B46.1.
B. The surface finish of raised face (RF) flanges for use with non-asbestos gaskets shall
be 3,2 to 6,3 µm Ra in accordance with ISO 468.
A. When reducing to or from screwed or socket welded construction, use a swage nipple.
C. For large diameter pipes, consideration shall be given to connections into butt welding
caps or heads in place of reducers. Such connections are not permitted without
SASOL’s approval.
A. Seal welding is required for all threaded joints in process lines except instrument
connections, thermometer wells and thermocouple wells and lines in Category D
service.
Page 14 of 21
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION GENERAL NOTES
C. When seal welding is specified for piping open to the atmosphere, only that piping
upstream of the last block valve need to be seal welded.
D. Pressure test vent and drain plugs shall be seal welded after the pressure test has been
completed.
1. Carbon steel and ferritic alloy steel pipe minimum bend radius five times
nominal pipe diameter.
2. Stainless steel, nickel-base alloy and aluminium pipe minimum bend radius
10 times the nominal pipe diameter.
Commodity Number
C. Threaded pipe shall only be allowed for Category D services, except that threaded
connections shall not be allowed in steam services.
Page 15 of 21
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION GENERAL NOTES
The method and extent of examination of piping systems assembled by welding (either shop
or field) shall be in accordance with Data Sheet E651, and as specified in Specifications
SP-90-2 and SP-90-2A.
B. Vent and drain connections to piping headers shall be made in accordance with details
shown on Drawing STDD-5059.
6. Use butt welding tees or welded-in contour inserts (i.e. sweepolets) when a line
is subject to severe pressure and/or temperature cycling and for pulsating
compressor piping.
Page 16 of 21
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION GENERAL NOTES
11. Threaded and socket weld unions and half couplings may be used.
2.12 BOLTING
2.13 GASKETS
Page 17 of 21
Copyright © 2007. Sasol. All rights reserved.
A
26160-000-50A10
PIPING MATERIAL FOSTER WHEELER SOUTH AFRICA (PTY) LTD PAGE 24 OF 353
SPECIFICATION ENGINEERING STANDARD REV F3
3 Branch Tables
Branch connection table for Atmospheric pressure and other low specification
services, i.e. piping line classes AAJ, AAK, AB, KH, KJ, L, LA, CAL.
For Branch Connections refer Branch Reinforcement Table for individual line
classes.
Page 18 of 21
W:\Project\Sasol\26160\Gen\08Eng\056pipspec\Piping Material
Specification\Rev F3_201202\00 26160-000-50A10 Rev F3.doc DSN: 10217
A
26160-000-50A10
PIPING MATERIAL FOSTER WHEELER SOUTH AFRICA (PTY) LTD PAGE 25 OF 353
SPECIFICATION ENGINEERING STANDARD REV F3
Branch connection table for low and medium pressure carbon steel lines, i.e. piping
line classes A, AA, AAA, AAB, AAH, AAM, ABA, AC, AX, AAE, AZT, LF, N, C, CA,
CAH, CBA, CX, R, RA, AAD, AAF, ADM, AND, AEM, CAD, CAF, CDM, CDN, CEM,
F, FC, FCA, S, SA, FEM, FAF, G.
For Branch Connections refer Branch Reinforcement Table for individual line
classes.
Page 19 of 21
W:\Project\Sasol\26160\Gen\08Eng\056pipspec\Piping Material
Specification\Rev F3_201202\00 26160-000-50A10 Rev F3.doc DSN: 10217
A
26160-000-50A10
PIPING MATERIAL FOSTER WHEELER SOUTH AFRICA (PTY) LTD PAGE 26 OF 353
SPECIFICATION ENGINEERING STANDARD REV F3
Branch connection table for stainless steel, alloy steel and high pressure carbon
steel lines, i.e. piping line classes ANB, ARR, ASB, ASJ, LB, CMB, CMX, CRB,
CRC, CRR, CSB, CSJ, CTC, FNMB, FTC, FUC, GSC, HSC, JTB, JTC, VA, VB, VC,
VD, ALA, ANC, AOA, AOB, AG, AWP, AF, CFC, CFD, CG, CGD, CH, CWP, FFC,
FFD, GFD, SF, H, J.
For Branch Connections refer Branch Reinforcement Table for individual line
classes.
Page 20 of 21
W:\Project\Sasol\26160\Gen\08Eng\056pipspec\Piping Material
Specification\Rev F3_201202\00 26160-000-50A10 Rev F3.doc DSN: 10217
A
26160-000-50A10
PIPING MATERIAL FOSTER WHEELER SOUTH AFRICA (PTY) LTD PAGE 27 OF 353
SPECIFICATION ENGINEERING STANDARD REV F3
Branch connection table for galvanised piping, i.e. piping line class LC.
For Branch Connections refer Branch Reinforcement Table for individual line
classes.
Page 21 of 21
W:\Project\Sasol\26160\Gen\08Eng\056pipspec\Piping Material
Specification\Rev F3_201202\00 26160-000-50A10 Rev F3.doc DSN: 10217
FOSTER WHEELER SOUTH AFRICA (PTY) LIMITED
PROJECT TITLE: FT Wax Expansion Project
PROJECT NUMBER: 26160
T: EQUAL TEE
4 RT&R RT&R RT RT RT T
WOL: WELDOLET
HEADER SIZE (NPS)
18 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RT T
20 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RT T
22 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RPD RT T
24 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RPD RPD RT T
28 2+R 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RPD RPD RPD T
56 2+R 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RPD RPD RT T
FOSTER WHEELER SOUTH AFRICA (PTY) LIMITED
PROJECT TITLE: FT Wax Expansion Project
PROJECT NUMBER: 26160
0.75 1 1.5 2 3 4 6 8 10 12 14 16 18 20 22 24
1 RT T
R: REDUCER
T: EQUAL TEE
4 RT&R RT&R RT RT RT T
WOL: WELDOLET
18 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RT T
20 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RT T
22 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RPD RT T
24 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RPD RPD RT T
FOSTER WHEELER SOUTH AFRICA (PTY) LIMITED
PROJECT TITLE: FT Wax Expansion Project
PROJECT NUMBER: 26160
1 RT T
R: REDUCER
T: EQUAL TEE
4 RT&R RT&R RT RT RT T
WOL: WELDOLET
18 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RT T
20 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RT T
22 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RPD RT T
24 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RPD RPD RT T
FOSTER WHEELER SOUTH AFRICA (PTY) LIMITED
PROJECT TITLE: FT Wax Expansion Project
PROJECT NUMBER: 26160
1 RT T
R: REDUCER
T: EQUAL TEE
4 RT&R RT&R RT RT RT T
WOL: WELDOLET
1 RT T
R: REDUCER
T: EQUAL TEE
4 RT&R RT&R RT RT RT T
WOL: WELDOLET
1 RT T
R: REDUCER
T: EQUAL TEE
4 RT&R RT&R RT RT RT T
WOL: WELDOLET
18 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RT T
20 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RT T
22 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RPD RT T
24 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RPD RPD RT T
FOSTER WHEELER SOUTH AFRICA (PTY) LIMITED
PROJECT TITLE: FT Wax Expansion Project
PROJECT NUMBER: 26160
T: EQUAL TEE
4 RT&R RT&R RT RT RT T
WOL: WELDOLET
36 RPD
FOSTER WHEELER SOUTH AFRICA (PTY) LIMITED
PROJECT TITLE: FT Wax Expansion Project
PROJECT NUMBER: 26160
1 RT T
R: REDUCER
T: EQUAL TEE
4 RT&R RT&R RT RT RT T
WOL: WELDOLET
1 RT T
R: REDUCER
T: EQUAL TEE
4 RT&R RT&R RT RT RT T
WOL: WELDOLET
1 T
R: REDUCER
T: EQUAL TEE
4 RT&R RT RT RT T
WOL: WELDOLET
1 RT T
R: REDUCER
T: EQUAL TEE
4 RT&R RT&R RT RT RT T
WOL: WELDOLET
NOT
12 2+R 2+R WOL WOL WOL WOL RT RT T
ALLOWED
1 RT T
R: REDUCER
T: EQUAL TEE
4 RT&R RT&R RT RT RT T
WOL: WELDOLET
18 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RT T
20 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RT T
22 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RPD RT T
24 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RPD RPD RT T
FOSTER WHEELER SOUTH AFRICA (PTY) LIMITED
PROJECT TITLE: FT Wax Expansion Project
PROJECT NUMBER: 26160
1 T
R: REDUCER
T: EQUAL TEE
4 RT&R RT RT RT T
WOL: WELDOLET
12
14
16
18
20
22
24
FOSTER WHEELER SOUTH AFRICA (PTY) LIMITED
PROJECT TITLE: FT Wax Expansion Project
PROJECT NUMBER: 26160
1 RT T
R: REDUCER
T: EQUAL TEE
4 RT&R RT&R RT RT RT T
WOL: WELDOLET
18 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RT T
20 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RT T
22 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RPD RT T
24 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RPD RPD RT T
FOSTER WHEELER SOUTH AFRICA (PTY) LIMITED
PROJECT TITLE: FT Wax Expansion Project
PROJECT NUMBER: 26160
1 RT T
R: REDUCER
T: EQUAL TEE
4 RT&R RT&R RT RT RT T
WOL: WELDOLET
NOT
12 2+R 2+R WOL WOL WOL WOL RT RT T
ALLOWED
14
16
18
20
22
24
FOSTER WHEELER SOUTH AFRICA (PTY) LIMITED
PROJECT TITLE: FT Wax Expansion Project
PROJECT NUMBER: 26160
1 RT T
R: REDUCER
T: EQUAL TEE
4 RT&R RT&R RT RT RT T
WOL: WELDOLET
10
12
14
16
18
20
22
24
FOSTER WHEELER SOUTH AFRICA (PTY) LIMITED
PROJECT TITLE: FT Wax Expansion Project
PROJECT NUMBER: 26160
1 RT T
R: REDUCER
T: EQUAL TEE
4 RT&R RT&R RT RT RT T
WOL: WELDOLET
1 RT T
R: REDUCER
T: EQUAL TEE
4 RT&R RT&R RT RT RT T
WOL: WELDOLET
1 RT T
R: REDUCER
T: EQUAL TEE
4 RT&R RT&R RT RT RT T
WOL: WELDOLET
18 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RT T
20 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RT T
22
24 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RPD RPD RT T
FOSTER WHEELER SOUTH AFRICA (PTY) LIMITED
PROJECT TITLE: FT Wax Expansion Project
PROJECT NUMBER: 26160
1 RT T
R: REDUCER
T: EQUAL TEE
4 RT&R RT&R RT RT RT T
WOL: WELDOLET
1 RT T
R: REDUCER
T: EQUAL TEE
4 RT&R RT&R RT RT RT T
WOL: WELDOLET
1 RT T
R: REDUCER
T: EQUAL TEE
4 RT&R RT&R RT RT RT T
WOL: WELDOLET
1 T
R: REDUCER
T: EQUAL TEE
4 RT&R RT RT RT T
WOL: WELDOLET
1 RT T
R: REDUCER
T: EQUAL TEE
4 RT&R RT&R RT RT RT T
WOL: WELDOLET
1
R: REDUCER
T: EQUAL TEE
4 SO
WOL: WELDOLET
6 SO SO
HEADER SIZE (NPS)
10
12
14
16
18
20
22
24
FOSTER WHEELER SOUTH AFRICA (PTY) LIMITED
PROJECT TITLE: FT Wax Expansion Project
PROJECT NUMBER: 26160
1
R: REDUCER
T: EQUAL TEE
4
WOL: WELDOLET
6 SO
HEADER SIZE (NPS)
10
12
14
16
18
20
22
24
FOSTER WHEELER SOUTH AFRICA (PTY) LIMITED
PROJECT TITLE: FT Wax Expansion Project
PROJECT NUMBER: 26160
1 RT T
R: REDUCER
T: EQUAL TEE
12 HCPL HCPL SO SO SO SO SO RT T
14 HCPL HCPL SO SO SO SO SO SO RT T
16 HCPL HCPL SO SO SO SO SO SO SO RT T
NOT ALLOWED
18 HCPL HCPL SO SO SO SO SO SO SO SO RT T
20 HCPL HCPL SO SO SO SO SO SO SO SO SO RT T
24 HCPL HCPL WOL SO SO SO RPD RPD RPD RPD RPD RPD RPD RT T
FOSTER WHEELER SOUTH AFRICA (PTY) LIMITED
PROJECT TITLE: FT Wax Expansion Project
PROJECT NUMBER: 26160
0.75 RT T
R: REDUCER
T: EQUAL TEE
3 RT&R RT RT RT RT T
WOL: WELDOLET
4 RT&R RT&R RT RT RT RT T
HEADER SIZE (NPS)
10
12
14
16
18
20
22
FOSTER WHEELER SOUTH AFRICA (PTY) LIMITED
PROJECT TITLE: FT Wax Expansion Project
PROJECT NUMBER: 26160
1 RT T
R: REDUCER
T: EQUAL TEE
4 RT&R RT&R RT RT RT T
NOT
10 HCPL HCPL SO SO SO SO RT T
ALLOWED
12
14
16
18
20
22
24
FOSTER WHEELER SOUTH AFRICA (PTY) LIMITED
PROJECT TITLE: FT Wax Expansion Project
PROJECT NUMBER: 26160
T: EQUAL TEE
4 RT&R RT&R RT RT RT T
WOL: WELDOLET
18 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RT T
NOT ALLOWED
20 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RT T
22 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RPD RT T
24 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RPD RPD RT T
26 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RPD RPD RPD RT T
28 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RPD RPD RPD RPD RT T
30 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RPD RPD RPD RPD RPD RT T
FOSTER WHEELER SOUTH AFRICA (PTY) LIMITED
PROJECT TITLE: FT Wax Expansion Project
PROJECT NUMBER: 26160
18 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RT T
20 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RT T
NOT ALLOWED
22 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RPD RT T
24 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RPD RPD RT T
26 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RPD RPD RPD RT T
28 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RPD RPD RPD RPD RT T
30 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RPD RPD RPD RPD RPD RT T
32 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RPD RPD RPD RPD RPD RPD RT T
34 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RPD RPD RPD RPD RPD RPD RPD RT T
36 2+R 2+R WOL WOL WOL WOL RPD RPD RPD RPD RPD RPD RPD RPD RPD RPD RPD RPD RPD RT T
FOSTER WHEELER SOUTH AFRICA (PTY) LIMITED
PROJECT TITLE: FT Wax Expansion Project
PROJECT NUMBER: 26160
1 T
R: REDUCER
T: EQUAL TEE
4 RT&R RT RT RT T
WOL: WELDOLET
1 RT T
R: REDUCER
T: EQUAL TEE
4 RT&R RT&R RT RT RT T
WOL: WELDOLET
APPENDIX A
BOLTING
1 SCOPE
This Appendix lists bolting materials and the criteria for selecting bolting to be used.
2 REQUIREMENTS
2.2 The selection of bolting materials to be used in the different service applications are listed in
Table 2.
2.3 Other types of bolting which might be considered more suitable for a particular application
shall be submitted to SASOL for review and written approval prior to purchase and
installation.
Page 1 of 3
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION APPENDIX A
NOTES:
1. All bolting material used in ASME Pressure Vessel Code application and bolting for
ASME B31.1 construction shall be ASME “SA” specifications. Bolting for ASME
B31.3 applications shall be ASTM “A” specifications.
2. When used in applications where the design temperature is higher than 400°C, bar
shall be made from vacuum-arc remelted steel and stress rupture tests at 650°C shall
be conducted for each heat of steel.
3. Material test reports shall be submitted in which the manufacturer records the results
of the tests conducted. In addition to the test results the documents shall also:
• give the actual impact test results or any other results of the test specifically
required,
• the results of chemical analysis and mechanical tests required by the basic
material specification.
Page 2 of 3
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION APPENDIX A
TEMPERATURE RANGE °C
SERVICE OR ASME
APPLICABLE MATERIAL USED 539 651
B16.5 PRESSURE
CODES IN CONSTRUCTION -250 -85 -45 -29 0 201 401
650 800
RATING
-86 -46 -30 0 200 400 538
(4) (4)
304L, 304 B8 L7 L7 B7 B7
LOW 9 Ni B8 L7 L7 B7 B7
TEMPERATURE
SERVICE 3½ Ni L7 L7 B7 B7
ASME B31.1 Carbon Steel L7 B7 B7
ASME B31.3 API Class 125 Cast Iron CA
620 Class 150 to 2500 Carbon Steel B7 B7 B16
API 650 Class 150 to 2500 Low Alloy Steel B7 B7 B16 8M
ASME I Class 150 to 600 304, 304H B7 B7 SS
ASME VIII
Class 150 to 600 304L, 316L B7 B7 B8(1)
Class 150 to 600 321, 347 B7 B7 8C 8M
Class 150 to 600 316, 316H B7 B7 8M 8M 8M
Class 900 and higher Austenitic Steel B7 SS SS 8M 8M
STRUCTURAL Normal Strength CA
STEEL High Strength CB CB(2)
AISC
SBR Ferritic Steel L7 L7 B7 CD
ANCHOR BOLTS Austenitic Steel B8/
B8 L7 L7 B7 B7 B8/8C 8M 8M
BM
LOW 304L, 304, 9 Ni B8 L7 L7 B7
TEMPERATURE
SERVICE 3½ Ni, Carbon Steel L7 B7
Cast Iron CA
STRUCTURAL GENERAL Carbon Steel B7 B7 B7 B7
MATERIALS
SUCH AS VESSEL Low Alloy B7 B7 B7 B16 8M
INTERNALS, 5 Chrome B7 B7 B5 8M
FURNACE 12 Chrome B6 B6 B6(3)
PARTS, etc.
CORROSION 8C/
304 (5) B7 B7 B8
RESISTANT 8M
316 (5) B7 B7 8M 8M 8M 8M
321, 347 (5) 8C 8C 8C 8C 8C
NOTES:
4. 8M bolting shall be A193 Grade B8M Class 1 with A194 Grade B8MA nuts.
5. B7 bolting shall be used if the bolting is not directly exposed to the corrosive process fluid,
and the temperature is below 400°C.
Page 3 of 3
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION APPENDIX C
APPENDIX C
1 SOUR SERVICE
1.1 When the environment is “sour” as defined in Paragraph 1.4.6 of the General Notes, the
selection of materials shall be limited to those listed as acceptable in NACE
Standard MR-01. The properties, chemistry and heat treatment requirements of MR-01 shall
also be met.
1.2 The limiting H2S concentration to prevent sulphide stress cracking is illustrated in
Figure AC.
2.1 Carbon and low alloy steels in the following heat treated conditions, and provided their
hardness does not exceed HRC 22, will be acceptable:
a. Annealed.
b. Normalized.
g. Cold worked carbon and alloy steels that have an extreme fibre deformation greater
that 5% shall be stress relieved at a minimum temperature of 595°C. The hardness
after heat treatment shall not exceed HRC 22.
Page 1 of 6
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION APPENDIX C
2.2 In addition to Paragraph 2.1 the following limiting chemistry for carbon and low alloy steel
shall also apply:
Wrought and cast 18/8 type austenitic stainless steels are acceptable in the solution annealed
condition to a maximum hardness of HRC 22. Free machining grades and grades with their
properties enhanced by cold work are not acceptable.
AISI 400 series ferritic stainless steels are acceptable in the annealed condition to a
maximum hardness HRC 22. Free machining grades are not permitted.
5.1 12 CHROMIUM
The 12% chromium martensitic stainless steels containing less than 0,15 carbon (410, CA15)
are acceptable for sour service provided their hardness does not exceed HRC 22 and
provided they have been heat treated as follows:
b. Double temper at 620°C minimum. The second tempering temperature shall be lower
than the first.
Page 2 of 6
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION APPENDIX C
Cast and wrought low carbon martensitic grades meeting the chemistry requirements of
ASTM A743 Class CA6NM and ASTM A-182 Class F6NM are acceptable to a maximum
hardness of HRC 22, when in the following heat treated condition:
6.1 Wrought 17Cr-4Ni precipitation hardening stainless steels are acceptable in the hardness
range HRC 29 to 33 when heat treated to one of the procedures in Appendix A of
NACE MR-01.
6.2 Precipitation hardening stainless steels with chemical compositions in accordance with
ASTM A453 Grade 660 or ASTM A638 Grade 660 are acceptable to a maximum hardness
HRC 35 if they are in the solution annealed and aged or double aged condition.
6.3 Precipitation hardening stainless steels with chemical compositions in accordance with UNS
S45000 are acceptable to a maximum hardness of HRC 31 when solution annealed and aged
at 621°C for a minimum of 4 hours.
Duplex (austenitic/ferritic) stainless steels are acceptable provided they are in the solution
annealed condition and their hardness does not exceed HRC 28.
Page 3 of 6
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION APPENDIX C
8 NON-FERROUS MATERIALS
Nickel, cobalt, aluminium or copper based alloys are acceptable within the restrictions
outlined in Section 4 of NACE MR-01. In some circumstances aluminium and copper based
alloys suffer accelerated corrosion in atmospheres that contain hydrogen sulphide.
9 OVERLAYS
Metallic coatings, conversion coatings and plastic coatings are not acceptable for preventing
hydrogen induced or hydrogen assisted cracking of base metals. In cases where weld or
sprayed metal overlays are applied for other reasons, the substrate material must meet all
requirements for sour service. If the substrate metal is heated above the critical temperature
during application of the overlay its hardness must be restored to the required level by post
weld heat treatment.
10 WELDING
10.1 Weldments must comply with the chemistry and hardness requirements for specified base
materials in sour services.
10.2 The welding procedure qualification shall include a Vickers hardness (HV10) traverse across
the weld, HAZ and base metal. No value shall exceed 250 HV10. The average value shall
be 240 HV10 or less.
10.3 The mechanical properties and chemical composition of the weld shall match that of the base
metal. Ferritic base metals welded with austenitic filler are not permitted. Welded joints
between austenitic and ferritic base metals are also prohibited.
Page 4 of 6
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION APPENDIX C
11 BOLTING
Bolting which will be directly exposed to a sour environment shall be selected in accordance
with the requirements of Section 6 of NACE MR-01.
12 CRYOGENIC SERVICES
12.1 The use of low alloy steels containing more than 1% Ni is only permitted when the service
temperature is below minus 25°C.
12.2 Nickel steels for cryogenic service shall be welded with matched filler if the hydrogen
sulphide partial pressure is above 30 Pa. An Inconel type filler is permitted if the hydrogen
sulphide partial pressure is below 30 Pa or if the hydrogen sulphide content of the gas is
below 1 ppm.
13 COMPRESSORS
If the hydrogen sulphide content in the compressed medium is greater than 1 ppm, materials
for shafts, blades, impellers and stationary parts, including the casing and diaphragms must
be selected for sour service. These requirements are not applicable to other parts not in
contact with the compressed medium.
Page 5 of 6
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION APPENDIX C
Page 6 of 6
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION APPENDIX D
APPENDIX D
Page 1 of 1
Copyright © 2007 Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION APPENDIX E
APPENDIX E
HYDROGEN SERVICE CHART
OPERATING LIMITS FOR STEELS IN HYDROGEN SERVICE
Page 1 of 1
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION APPENDIX F
APPENDIX F
1.1 In the selection of steels exposed to hydrocarbon containing hydrogen sulphide, at operating
temperatures above 200°C, the following variables shall be known:
1.1.3 Diluent:NAPHTHA or gas-oil (necessary only for carbon steel and chromium alloy steels
through 9 chrome).
a. NAPHTHA: a fraction of petroleum with a boiling point range and volatility between
that of gasoline and kerosene.
b. Gas-oil: a liquid petroleum distillate with a viscosity and boiling point range
between that of kerosene and lubricating oil.
1.2 Selection of steels shall be in accordance with the hydrogen sulphide service chart.
EXAMPLE "A"
Operating temperature 250°C
Mole % H2S 0,1
Diluent Gas-oil
Material selection Carbon steel
Operating temperature 300°C
Mole % H2S 0,1
Diluent NAPHTHA
Material selection 5 chrome
Page 1 of 3
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION APPENDIX F
1.3 Limitations of steels shown on the hydrogen sulphide service chart are based on a corrosion
rate of 0,1 mm per year.
1.4 When specific steels are required to be used above the limitations shown on the hydrogen
sulphide service chart, the corrosion rate shall be established in accordance with “Computer
Correlations to Estimate Corrosion of Steels by Refinery Streams Containing Hydrogen
Sulphide”, by Couper and Gorman, National Association of Corrosion Engineers, Paper
Number 67.
Page 2 of 3
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION APPENDIX F
Page 3 of 3
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION APPENDIX G
APPENDIX G
HYDROFLUORIC ACID GRAPH
Page 1 of 1
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION APPENDIX H
APPENDIX H
COLOUR CODING OF PIPING MATERIAL
GREEN Carbon steel to ASTM A106 and ASTM A672, Class 22 or 32 and
equivalent material specified with supplementary requirements
GREEN/RED Carbon steel material specified to an ASME-SA material
specification with supplementary requirements
WHITE Seamless carbon steel piping to API 5L Grade B or ASTM A53,
Grade B and equivalent material
PINK ERW carbon steel piping to API 5L Grade B or ASTM A53 Grade B
PINK/WHITE EFW carbon steel pipe DSAW API 5L Grade B or ASTM A53
Grade B
YELLOW/RED Low temperature carbon steel materials, e.g. ASTM A333 Grade 6,
A671 Grade CC60 Class 22
ORANGE SABS 719 Grade B carbon steel pipe
BLACK Seamless carbon steel pipe to API 5L Grade A, ASTM A53 Grade A
and A106 Grade A
GREEN/ YELLOW / BLUE 3CR12
YELLOW/ PURPLE Low temperature 3,5% Ni piping materials, e.g. ASTM A333
Grade 3, A671 Grade CF66 Class 22
YELLOW Carbon - ½ Moly material UNS K11522
YELLOW/ GREEN 1¼Cr-½Mo piping materials, e.g. ASTM A335 Grade P11, A691
Grade 1¼Cr Class 22 UNS K11597
YELLOW/ GREEN / YELLOW 2¼Cr-1Mo, ASTM A335 Grade P22 UNS K21590
YELLOW/BLUE 5Cr-½Mo alloy steel pipe to ASTM A335 Grade P5 and A691 Grade
5Cr Class 22 UNS K41545
YELLOW/ BLUE/ YELLOW 9Cr-½Mo A335 Grade P9, A691 Grade 9Cr Class 22, A234
Grade WP9 UNS K81590
YELLOW/ BROWN Austenitic stainless steel Type 304 UNS S30400
Page 1 of 2
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION APPENDIX H
Page 2 of 2
Copyright © 2007. Sasol. All rights reserved.
Specification note numbers - Project No.: 26160
Note Number Note
8 All flanged joints, including valve bonnets, shall be fitted with indicating spray shields.
9 No copper or copper bearing alloy permitted.
23 Materials selected for this line class shall conform to SP-90-18, LT 45.
26 Minimum size for instrument connections is NPS 1/2. Minimum size for process connections is NPS 3/4.
51 All underground pipe and fittings shall be externally coated and wrapped in accordance with SP-50-6.
100 Use for flanged vent, drain and branch connections.
101 Use for valved vent, drain and branch connections.
102 Use only for instrument connections.
103 Use only for fuel gas service (except burner leads).
106 Use for valved branch connections.
107 Use steel valves against storage tank nozzles and at battery limits in supply and return lines.
108 Use for branch connections to flare headers.
110 Use only for plugged pressure test vent and drain connections.
112 Valves shall not be insulated - see general note 2.1(i).
123 Use only at utility stations.
125 Use only as breakout flanges i.e. Pipe flange to pipe flange connections.
126 Use NPS 2 through NPS 4 only for boiler feedwater.
127 Use where flanged valve is required at NPS 1 and NPS 1½ connections to tanks, vessels and equipment.
128 Use only when valves can be adequately supported and when note 101 and/or 127 is not governing.
130 Temperature range -45°c to -30°c.
133 Temperature range 0°c to 400°c.
135 Temperature range -29°c to +175°c.
136 Temperature range 401°c to 538°c.
144 Temperature range 401°c to 455°c.
145 Temperature range 401°c to 427°c.
149 Temperature range 0°c to 60°c. Pressure limited to 1035 kPa.
153 Do not install against raised face flanges. All flanges shall have flat faces.
159 For bonnet gasket and stem packing, see SP-50-10.
160 Valves for -45°c service shall conform to SP-50-10c.
175 Use for vent, drain and instrument connections in isopropyl ether service.
180 Do not use for boiler feedwater.
181 Do not use for ammonia water and isopropyl ether service.
186 Do not use for phenol service.
187 Use only for phenol service.
190 Do not use for isopropyl ether service.
APPENDIX K
COMPONENT LIST (SHORT NAME)
SHORT
ITEM DESCRIPTION
NAME
ACCV ACCESS COVER
ADAP ADAPTOR
ANGV ANGLE VALVE – FLANGED
B--- BALL VALVE 1ST DIGIT B
ND
2 DIGIT
BA-- FULL BORE A
BR-- REDUCED BORE R
BT-- TOP ENTRY T
RD
3 DIGIT
B–F- FIRE SAFE F
B–G- FIRE SAFE REGULAR PATTERN G
B–H- FIRE SAFE SHORT PATTERN H
B–S- LONG PATTERN R
B–S- SHORT PATTERN S
TH
4 DIGIT
B–-B BUTT WELD B
B--F FLANGED F
B--S SOCKET WELD S
B--T THREADED T
BFFF FLANGE - LAP JOINT BACKING
BLFF FLANGE - BLIND - FLAT FACE
BLGR FLANGE - BLIND - GROOVED
BLRF FLANGE - BLIND - RAISED FACE
BLRJ FLANGE - BLIND - RING JOINT
BLSF FLANGE - BLIND - RAISED FACE - SMOOTH FINISH
BLTF FLANGE - BLIND - TONGUE
BLTW FLANGE - BLIND - THERMOWELL BACKING
BLTW BACKING FLANGE - THERMOWELL
BRFF BLEED RING - FLAT FACE
BRFS BRANCH BY FULL COUPLING - SCREWED
Page 1 of 9
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION APPENDIX K
SHORT
ITEM DESCRIPTION
NAME
BRFW BRANCH BY FULL COUPLING - SOCKET WELD
BRHS BRANCH BY HALF COUPLING - SCREWED
BRHW BRANCH BY HALF COUPLING - SOCKET WELD
BRRF BLEED RING - RAISED FACE
BRRJ BLEED RING - RING JOINT
BRSF BLEED RING - RAISED FACE - SMOOTH FINISH
BTFF BUTTERFLY VALVE - FLANGED - FLAT FACE
BTFW BUTTERFLY VALVE - WAFER TYPE
BTFY BUTTERFLY VALVE - ECCENTRIC DISC
BTRF BUTTERFLY VALVE - FLANGED - RAISED FACE
BTSF BUTTERFLY VALVE - FLANGED - RAISED FACE - SMOOTH FINISH
BTVG BUTTERFLY VALVE WITH GEAR - SERIES 700, 704
BTVL BUTTERFLY VALVE WITH HANDLE - SERIES 700
BUSF BUSHING
BUSF FACE BUSHING - MALE TRAP ADAPTER
BUSX BUSHING HEX
CAPP CAP - BUTT WELD
CASC CAP - SCREWED
CASW CAP - SOCKET WELD
CFGR FLANGE - VITAULIC - ADAPTER
CHBT CHECK VALVE - BALL TYPE
CHBW CHECK VALVE - BUTT WELD
CHKV CHECK VALVE - FLANGED - SWING TYPE
CHKW CHECK VALVE - FLANGED - DOUBLE DOOR
CHPT CHECK VALVE - PISTON TYPE
CHSC CHECK VALVE - SCREWED
CHSW CHECK VALVE - SOCKET WELD
CHVA SEWER VALVE - WITH CHECK
CHWS CHECK VALVE - WAFER TYPE - SWING TYPE (SINGLE PLATE - SPLT)
CHWT CHECK VALVE - WAFER TYPE - DOUBLE DOOR (DUAL PLATE - DPLT)
COGR COUPLING - OUTLET
CPDR COUPLING - DRESSER STYLE 38
CPFS FULL COUPLING - SCREWED
Page 2 of 9
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION APPENDIX K
SHORT
ITEM DESCRIPTION
NAME
CPFW FULL COUPLING - SOCKET WELD
CPGR COUPLING – VITAULIC - STANDARD
CPHS HALF COUPLING - SCREWED
CPHW HALF COUPLING - SOCKET WELD
CPRS COUPLING – REDUCING - SCREWED
CPRW COUPLING - REDUCING - SOCKET WELD
CPSR COUPLING – REDUCING WITH STOP
CPSS COUPLING - SOCKET WELD - SCREWED
CPVT COUPLING – VITAULIC STYLE 99
CRED REDUCER - CONCENTRIC - BUTT WELD
CREF REDUCER – CONCENTRIC - FLANGED
CRGR COUPLING - REDUCING - STYLE 750
CROF CROSS - FLANGED
CROS CROSS - BUTT WELD
CRSC CROSS - SCREWED
CRSW CROSS - SOCKET WELD
CTRV CONTROL VALVE - FLANGED
DIAP DIAPHRAGM
DLEX DOUBLE ELL
DLRX DOUBLE ELL - STRAIGHT
E18X RETURN BEND - BUTT WELD ENDS
E5D9 BEND - 5 DIAMETER - 90 DEGREE
E5DR BEND - 5 DIAMETER RETURN - 180 DEGREE
E5R4 ELBOW - 45 DEGREE - 5 RADIUS
E5R9 ELBOW - 90 DEGREE - 5 RADIUS
EC18 RETURN BEND - WITH CLEANOUT
ELF4 ELBOW - 45 DEGREE - FLANGED
ELF9 ELBOW - 90 DEGREE - FLANGED
ELR3 ELBOW - 30 DEGREE - LONG RADIUS - BUTT WELD ENDS
ELR4 ELBOW - 45 DEGREE - LONG RADIUS - BUTT WELD ENDS
ELR6 ELBOW - 60 DEGREE - LONG RADIUS - BUTT WELD ENDS
ELR9 ELBOW - 90 DEGREE - LONG RADIUS - BUTT WELD ENDS
ELRR RETURN BEND - 180 DEGREE - LONG RADIUS - BUTT WELD ENDS
Page 3 of 9
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION APPENDIX K
SHORT
ITEM DESCRIPTION
NAME
ELT4 ELBOW - TANGENT - 45 DEGREE - LONG RADIUS - BUTT WELD ENDS
ELT9 ELBOW – TANGENT - 90 DEGREE - LONG RADIUS - BUTT WELD ENDS
ERED REDUCER - ECCENTRIC - BUTT WELD ENDS
EREF REDUCER – ECCENTRIC - FLANGED
EREX REDUCER – ECCENTRIC
ERF9 REDUCING ELBOW - 90 EDGREE - FLANGED
ESC4 ELBOW - 45 DEGREE - SHORT RADIUS - SCREWED
ESC9 ELBOW - 90 DEGREE - SHORT RADIUS - SCREWED
ESR9 ELBOW - 90 DEGREE - SHORT RADIUS - BUTT WELD ENDS
ESRR RETURN BEND - 180 DEGREE - SHORT RADIUS - BUTT WELD ENDS
ESW4 ELBOW - 45 DEGREE - SOCKET WELD
ESW9 ELBOW - 90 DEGREE - SOCKET WELD
GASK GASKET
GATV GATE VALVE - FLANGED
GLBV GLOBE VALVE - FLANGED
GLBW GLOBE VALVE - BUTT WELD
GLSC GLOBE VALVE - THREADED
GLSS GLOBE VALVE - SOCKET WELD/THREADED
GLSW GLOBE VALVE - SOCKET WELD
GVBW GATE VALVE - BUTT WELD
GVSC GATE VALVE - SCREWED
GVST GATE VALVE - SOCKET WELD/THREADED
GVSW GATE VALVE - SOCKET WELD
JWRF FLANGE - WELD NECK - JACKETED
KNGV KNIFE GATE VALVE - FLANGED
LFLB FLANGE - LAP FACE - TYPE B
LFLG FLANGE - LAP FACE - TYPE G
LFLV FLANGE - LAP FACE - SHORT STUB END
LT18 RETURN BEND - LONG TANGENT - 180 DEGREE
LTBW LATROLET - BUTT WELD
LTSW LATROLET - SOCKET WELD
LTTH LATROLET - THREADED
NEDT NEEDLE VALVE - THREADED
Page 4 of 9
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION APPENDIX K
SHORT
ITEM DESCRIPTION
NAME
NEDV NEEDLE VALVE - FLANGED
NIPL PIPE NIPPLE - VARYING END TYPES
NLET BRANCH NIPPLE - (NIPOLET)
PIPE PIPE
PELP PIPE - POLYETHYLENE LINED
PPLP PIPE - POLYPROPYLENE LINED
PTLP PIPE - TEFLON LINED
P--- PLUG VALVE 1ST DIGIT P
ND
2 DIGIT
PL-- LUBRICATED L
PN-- NON-LUBRICATED N
RD
3 DIGIT
P–F- FIRE SAFE F
P–J- JACKETED J
P–L- LINED L
P–N- LONG PATTERN N
P–R- REGULAR PATTERN R
P–S- SHORT PATTERN S
P–V- VENTURI PATTERN V
TH
4 DIGIT
P–-B BUTT WELD B
P--F FLANGED F
P--S SOCKET WELD S
P--T THREADED T
PLHX PLUG – HEXAGONHEAD - SCREWED
PLRH PLUG - ROUND HEAD - SCREWED
PLSQ PLUG - SQUARE HEAD - SCREWED
RADP REDUCING ADAPTER
REL9 REDUCING ELBOW - 90 DEGREE - BUTT WELD
RES9 REDUCING ELBOW - 90 DEGREE - SCREWED
REX9 REDUCING ELBOW
RFSF FLANGE - RAISED FACE - SMOOTH FINISH
RTEE REDUCING TEE - BUTT WELD
Page 5 of 9
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION APPENDIX K
SHORT
ITEM DESCRIPTION
NAME
RTRD RUNNING TRAP - WITH PLUG
RTRP RUNNING TRAP - WITH CLEANOUT
RTSC REDUCING TEE - SCREWED
RTSW REDUCING TEE - SOCKET WELD
SELT ELBOWLET - SOCKET WELDED
SGNC SWAGE NIPPLE - CONCENTRIC – VARYING END TYPES
SGNE SWAGE NIPPLE - ECCENTRIC - VARYING END TYPES
SLET SOCKOLET
SOFF FLANGE - SLIP ON – FLAT FACE
SORF FLANGE - SLIP ON - RAISED FACE
SORJ FLANGE - SLIP ON - RING JOINT
SOSF FLANGE - SLIP ON - RAISED FACE SMOOTH FINISH
SPFF SPECTACLE BLIND - FLAT FACE
SPRF SPECTACLE BLIND - RAISED FACE
SPRJ SPECTACLE BLIND - RING JOINT
SPRS SPECTACLE BLIND - RAISED FACE - SMOOTH FINISH
SPSF SPRAY SHIELD - FLANGE CONNECTION
SPST SPRAY SHIELD - SCREWED CONNECTION
STEE STRAIGHT TEE - BUTT WELD
STEF STRAIGHT TEE - FLANGED
STRN STRAINER
STSC STRAIGHT TEE - SCREWED
STSW STRAIGHT TEE - SOCKET WELD
STUB LAP JOINT STUB END
SWFF FLANGE - SOCKET WELD - FLAT FACE
SWRF FLANGE - SOCKET WELD - RAISED FACE
SWSF FLANGE - SOCKET WELD - RAISED FACE SMOOTH FINISH
SXSC CROSS TEE - SCREWED
TELT ELBOWLET - THREADED
THFF FLANGE - THREADED - FLAT FACE
THRF FLANGE - THREADED - RAISED FACE
TLET THREADOLET
TRAP TRAP
Page 6 of 9
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION APPENDIX K
SHORT
ITEM DESCRIPTION
NAME
TSSS TEE - SOCKET WELD - SOCKET WELD - THREADED
TSTB TEE - TEST - WITHOUT PLUG
TSTX TEE - TEST - WITH PLUG
TUBE TUBE
UNRX UNION - REDUCING
UNSC UNION - SCREWED
UNSW UNION - SOCKET WELD
WELT ELBOWLET - BUTT WELD
WLET WELDOLET
WNFE FLANGE - WELD NECK - FEMALE END
WNFF FLANGE - WELD NECK - FLAT FACE
WNFR FLANGE - WELD NECK - FEMALE END - TYPE R
WNGR FLANGE - WELD NECK - GROOVED END
WNLB FLANGE - LONG WELD NECK - BALL TYPE JOINT
WNLF FLANGE - LONG WELD NECK - RAISED FACE
WNLJ FLANGE - LONG WELD NECK - LAP JOINT
WNLR FLANGE - LONG WELD NECK - RING JOINT
WNLS FLANGE - LONG WELD NECK - RAISED FACE SMOOTH FINISH
WNME FLANGE - WELD NECK - MALE END
WNMJ FLANGE - WELD NECK - MALE END JOINT
WNMV FLANGE - WELD NECK - MALE END - TYPE V
WNOF WELD NECK ORIFICE FLANGE SET - FLAT FACE
WNOJ WELD NECK ORIFICE FLANGE SET - RING JOINT
WNOR WELD NECK ORIFICE FLANGE SET - RAISED FACE
WNOS WELD NECK ORIFICE FLANGE SET - RAISED FACE SMOOTH FINISH
WNRF FLANGE - WELD NECK - RAISED FACE
WNRJ FLANGE - WELD NECK - RING JOINT FACE
WNSF FLANGE - WELD NECK - RAISED FACE SMOOTH FINISH
WNTF FLANGE - WELD NECK - TONGUE END
YSRV STRAINER - "Y" TYPE - FLANGED
YSWW STRAINER - "Y" TYPE - SOCKET WELD
Page 7 of 9
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION APPENDIX K
GENERAL ABBREVIATIONS
LUBR LUBRICATED
NLUB NON-LUBRICATED
Page 8 of 9
Copyright © 2007. Sasol. All rights reserved.
SP-50-3A
Revision 7
July 2007
PIPING MATERIAL SPECIFICATION APPENDIX K
Page 9 of 9
Copyright © 2007. Sasol. All rights reserved.
Line Class Index
Client: Sasol
Contract No: 26160
Contract Description: FT Wax Expansion Project
Line Rev General Material / Pressure / Corrosion Stress Relief Weld Quality Max Line Class Construction Line class limits Line class service
Class Rating / Facing Temperature Rating Allowance Requirements Inspection Hydrotest (allowable pressure /
Material Group Pressure temperature)
A F3 Carbon Steel / CL150 ASME B16.5 / Group 1.1 1.0 mm Per SP-90-2A Per SP-90-2A See Isometric NPS 1 and smaller - Socket Weld / 0°C : 1960kPa Air (Instrument) : 16°C - 60°C
RF NPS 1½ and larger - Butt Weld
38°C : 1960kPa Air (Process) : 0°C - 400°C
50°C : 1920kPa
100°C : 1770kPa Air (utility) : 0°C - 60°C
150°C : 1580kPa CO2 (Dry) : 0°C - 400°C
200°C : 1380kPa
250°C : 1210kPa Flare Gas : 0°C - 400°C
300°C : 1020kPa Fuel Gas : 0°C - 230°C
325°C : 930kPa
350°C : 840kPa Fuel Oil : 0°C - 200°C
375°C : 740kPa Hydrocarbons : 0°C - 400°C
400°C : 650kPa
Nitrogen : 0°C - 400°C
A1 F3 Carbon Steel / CL150 ASME B16.5 / Group 1.1 1.0 mm Per SP-90-2A Per SP-90-2A See Isometric NPS 1 and smaller - Socket Weld / 0°C : 1960kPa Aboveground Fire : 0°C - 60°C
RF NPS 1½ and larger - Butt Weld Water Distribution
38°C : 1960kPa Foam : 0°C - 60°C
50°C : 1920kPa
60°C : 1890kPa Low Pressure Nitrogen : 0°C - 60°C
90°C : 1800kPa Steam (exhaust) : 0°C - 90°C
AZT Carbon Steel / CL150 ASME B16.5 / Group 1.1 1.0 mm Per SP-90-2A Per SP-90-2A See Isometric NPS 1 and smaller - Socket Weld / 0°C : 1960kPa Note 73: : Velocity limited to 2.5m/s
RF NPS 1½ and larger - Butt Weld
38°C : 1960kPa Phenol (Concentration : 0 Deg C - 80 Deg C
50°C : 1920kPa shall be 70%
80°C : 1830kPa
C F3 Carbon Steel / CL300 ASME B16.5 / Group 1.1 1.0 mm Per SP-90-2A See SP-90-2A See Isometric NPS 1" and smaller - Socket Weld 0°C : 5110kPa Air (Process), Nitrogen : 0°C - 400°C
RF / NPS 1½"and larger - Butt Weld
38°C : 5110kPa Amine, Carbonates : 0°C - 60°C
50°C : 5010kPa (Note 73)
100°C : 4660kPa Hydrocarbons : 0°C - 400°C
150°C : 4510kPa Hydrogen (Note 11) : See Appendix E
200°C : 4380kPa
250°C : 4190kPa Nitrogen (Purge) : 0°C - 230°C
300°C : 3980kPa Note 11 : See Appendix E for Pr-Te
325°C : 3870kPa limits in Hydrogen Ser.
350°C : 3760kPa Note 73 : Velocity limited to 2.5 m/s
375°C : 3640kPa Water (Process), : 0°C - 400°C
400°C : 3470kPa Methanol
LF F3 Carbon Steel / CL150 ASME B16.5 / Group 1.1 2.5 mm Per SP-90-2A Per SP-90-2A See Isometric NPS 1 and smaller - Socket Weld / 0°C : 1600kPa Underground Fire : 0 Deg C - 60 Deg C
FF NPS 1½ and larger - Butt Weld Water Distribution
38°C : 1600kPa
60°C : 1600kPa
N F3 Carbon Steel / CL150 ASME B16.5 / Group 1.1 1.0 mm Per SP-90-2A Per SP-90-2A See Isometric NPS 1" and smaller - Socket Weld 0°C : 1960kPa Boiler Feedwater : 0°C - 400°C
RF / NPS 1½" and larger - Butt Weld
38°C : 1960kPa Condensate : 0°C - 400°C
50°C : 1920kPa
100°C : 1770kPa Steam : 0°C - 400°C
150°C : 1580kPa Tempered Water : 0°C - 400°C
200°C : 1380kPa
250°C : 1210kPa
300°C : 1020kPa
325°C : 930kPa
350°C : 840kPa
375°C : 740kPa
400°C : 650kPa
Pressure: 1960kPa 1960kPa 1920kPa 1770kPa 1580kPa 1380kPa 1210kPa 1020kPa 930kPa 840kPa 740kPa 650kPa
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1541S003 0356234 Pipe PE API-5L-B SMLS 0.5 0.5 XS - - XS 26 - - SSSF
- 1541S003 0356234 Pipe PE API-5L-B SMLS 0.75 0.75 XS - - XS 26 - - SSSF
- 1541S003 0356234 Pipe PE API-5L-B SMLS 1 1 XS - - XS 26 - - SSSF
- 1541S001 0356234 Pipe BE API-5L-B SMLS 1.5 1.5 XS - - XS - - - SSSF
- 1541X001 0356649 Pipe BE API-5L-B ERW 2 2 STD - - STD - - - SSSF
- 1541X001 0356649 Pipe BE API-5L-B ERW 2.5 2.5 STD - - STD - - - SSSF
- 1541X001 0356649 Pipe BE API-5L-B ERW 3 3 STD - - STD - - - SSSF
- 1541X001 0356649 Pipe BE API-5L-B ERW 4 4 STD - - STD - - - SSSF
- 1541X001 0356649 Pipe BE API-5L-B ERW 6 6 STD - - STD - - - SSSF
- 1541X001 0356646 Pipe BE API-5L-B ERW 8 8 Sch 20 - - Sch 20 - - - SSSF
- 1541X001 0356646 Pipe BE API-5L-B ERW 10 10 Sch 20 - - Sch 20 - - - SSSF
- 1541X001 0356646 Pipe BE API-5L-B ERW 12 12 Sch 20 - - Sch 20 - - - SSSF
- 1541X001 0356645 Pipe BE API-5L-B ERW 14 14 Sch 10 - - Sch 10 - - - SSSF
- 1541X001 0356645 Pipe BE API-5L-B ERW 16 16 Sch 10 - - Sch 10 - - - SSSF
- 1541X001 0356645 Pipe BE API-5L-B ERW 18 18 Sch 10 - - Sch 10 - - - SSSF
- 1541X001 0356645 Pipe BE API-5L-B ERW 20 20 Sch 10 - - Sch 10 - - - SSSF
- 1541X001 0356649 Pipe BE API-5L-B ERW 22 22 STD - - STD - - - SSSF
- 1541X001 0356649 Pipe BE API-5L-B ERW 24 24 STD - - STD - - - SSSF
- 1541X001 0356649 Pipe BE API-5L-B ERW 26 26 STD - - STD - - - SSSF
- 1541X001 0356649 Pipe BE API-5L-B ERW 28 28 STD - - STD - - - SSSF
- 1541X001 0356649 Pipe BE API-5L-B ERW 30 30 STD - - STD - - - SSSF
- 1541X00E Pipe PE API-5L-B DSAW 0.375" WALL 56 56 0.375" - - 0.375" - - - SSSF
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
714 1512G00A 0115373 Gate SWE X FTE CL800 A105 WB F6/Stell Trm 0.5 1 - - - - 102 - - SSSF
USE 45° LATROLETS ONLY FOR FLARE CONNECTIONS. Use Full Bore Gate Valves only where indicated on MFD's with notes.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and smaller - Socket Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
USE 45° LATROLETS ONLY FOR FLARE CONNECTIONS. Use Full Bore Gate Valves only where indicated on MFD's with notes.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and smaller - Socket Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
USE 45° LATROLETS ONLY FOR FLARE CONNECTIONS. Use Full Bore Gate Valves only where indicated on MFD's with notes.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and smaller - Socket Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
USE 45° LATROLETS ONLY FOR FLARE CONNECTIONS. Use Full Bore Gate Valves only where indicated on MFD's with notes.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and smaller - Socket Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
USE 45° LATROLETS ONLY FOR FLARE CONNECTIONS. Use Full Bore Gate Valves only where indicated on MFD's with notes.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and smaller - Socket Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
USE 45° LATROLETS ONLY FOR FLARE CONNECTIONS. Use Full Bore Gate Valves only where indicated on MFD's with notes.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and smaller - Socket Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
USE 45° LATROLETS ONLY FOR FLARE CONNECTIONS. Use Full Bore Gate Valves only where indicated on MFD's with notes.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and smaller - Socket Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1511B018 Full Bore, Top Entry, Valves to comply with API-608. Ball-316SS/HC, Seat-316SS/stellite, Body Seal-316SS graphite, Packing-graphite. Firesafe, Blowout Proof Stem. Valve seats and seals shall be rated
for the same pressue-temperature rating as of the shell, to ASME B16.34. Supplier shall provide coating procedure for hard chrome facing to substantiate peeling concerns and Standard body cavity
pressure relief design.
USE 45° LATROLETS ONLY FOR FLARE CONNECTIONS. Use Full Bore Gate Valves only where indicated on MFD's with notes.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and smaller - Socket Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1511B01B Bi-Directional Flow, Full Bore, Top Entry, Valves to comply with API-608. Ball-316SS/HC, Seat-316SS/stellite, Body Seal-316SS graphite, Packing-graphite. Bi-Directional Flow. Rated for shut-off against fu
B16.34 differential pressures in both directions. Tightness Rates:- Allowable leakage rate at full differential pressure rated to ASME/FCI 70-2 Class V. Firesafe, Blowout Proof Stem. Valve seats and seals
shall be rated for the same pressue-temperature rating as of the shell, to ASME B16.34. Supplier shall provide coating procedure for hard chrome facing to substantiate peeling concerns and Standard bod
cavity pressure relief design. Valve in Errosive Service. Design Condition: 1500 kPag @ 170°C.
1511C02A Integral seating surfaces, Inconel-X spring, 316SS hinge pin / stop pin / pin retainers / lug bearings API-594:-Type A, Dual Plate Double Flanged Check Valve
1511D00D Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1511D02X Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1511F00A Category B Lug Type, Body A216-WCB, Seat BUNA-N, Disc CS with 304SS seating, Seating Weld Overlay with min thk of 1.6mm, Shaft- 304SS. Valve shall be supplied with Leverlock Positioning handle
to faciliate for valve to be locked in intermediate positions. Valve shall be rated for shut-off at 1035 kPa @ 60°C. Bolt Holes on Lug Pattern Shall be through drilled. Electrostatic feature. Valve Lever Lock
handle shall be furnished with a lockable device that accepts a purchaser-supplied lock to enable valve to be locked in positions. Supplier shall confirm that mating pipework bore will give adequate disc
swing clearance. (Pipe Schedules: 6"-Std, 8-12-S-20, 14-20-S-10, 24"-Std)
1511F00B Category B Lug Type, Body A216-WCB, Seat BUNA-N, Disc CS with 304SS seating, Seating Weld Overlay with min thk of 1.6mm, Shaft- 304SS. Valve shall be supplied with Leverlock Positioning handle
to faciliate for valve to be locked in intermediate positions. Valve shall be rated for shut-off at 1035 kPa @ 60°C. Bolt Holes on Lug Pattern Shall be through drilled. Electrostatic feature. Valve Lever Lock
handle shall be furnished with a lockable device that accepts a purchaser-supplied lock to enable valve to be locked in positions. Supplier shall confirm that mating pipework bore will give adequate disc
swing clearance. (Pipe Schedules: 6"-Std, 8-12-S-20, 14-20-S-10, 24"-Std)
1511G002 Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1511G003 Flanges >24" to match ASME B16.47, Series B Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler
1511G004 Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1511G00H Full Bore Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1511G03S Flanges >24" to match ASME B16.47, Series B Full Bore. Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with
Graphite filler.
1511P004 Supplier shall specify Lubricant suitable for the service. (Fuel Gas to 170°C). Anti-static feature
USE 45° LATROLETS ONLY FOR FLARE CONNECTIONS. Use Full Bore Gate Valves only where indicated on MFD's with notes.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and smaller - Socket Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1512B00Y Valves to comply with the requirements of BS 5351. Anti blow out stem. Fire safe to BS 6755-2. Floating ball. Valves to be supplied complete with 150mm long plain ended A106-B seamless (Sch 80)
extension pipe pups socket welded to the valves on both ends. Valve design shall be such that all parts can be easily serviced or replaced in-line. Standard body cavity pressure relief design.
1512B016 Full Bore, Top Entry, Valves to comply with API-608. Ball-316SS/HC, Seat-316SS/stellite, Body Seal-316SS graphite, Packing-graphite. Firesafe, Blowout Proof Stem. Valve seats and seals shall be rated
for the same pressue-temperature rating as of the shell, to ASME B16.34. Supplier shall provide coating procedure for hard chrome facing to substantiate peeling concerns and Standard body cavity
pressure relief design. Valve in Errosive Service.
1512B018 Bi-Directional Flow, Full Bore, Top Entry, Valves to comply with API-608. Ball-316SS/HC, Seat-316SS/stellite, Body Seal-316SS graphite, Packing-graphite. Bi-Directional Flow, Rated for shut-off against fu
B16.34 differential pressures in both directions. Tightness Rates: Allowable leakage rate at full differential pressure rated to ASME/FCI 70-2 Class V. Firesafe, Blowout Proof Stem. Valve seats and seals
shall be rated for the same pressure-temperature rating as of the shell, to ASME B16.34. Supplier shall provide coating procedure for hard chrome facing to substantiate peeling concerns and Standard
body cavity pressure relief design. Valve in Errosive Service.
1512D005 Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated. Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512D01J Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated.
1512G00B Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G02C Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G02D Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G02L Graph Packing Full Bore. Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1541X00E PSL 1 Grade. Longitudinal weld seams only. No. of weld seams to be submitted with Bid & confirmed prior to order placement & fabrication. Plates used to be free of welds and/or defects. Refer ISO 3183
Pipe delivered shall be subject to 100% radiography & hydrotested. As the pipe is being used for Fabricaton of RF Pads, these can alternatively be rolled from A516-60 or 70 plate, 2m long & 10mm thick.
The plate ID shall be rolled to suit OD of a 56" pipe. Plate shall be delivered rolled in 2 halfs split along the longitudnal axis, without weld seams or strikes & shall have a material certificate.
1551E00E To be supplied with 75mm straight after bend at both ends.Bend radius to be 5 x NPS. Seamless. The Supplier shall make provision for thinning during bending to meet the minimum wall thickness after
bending. The minimum thickness at the end tangents shall not be less than the pipe thickness.
USE 45° LATROLETS ONLY FOR FLARE CONNECTIONS. Use Full Bore Gate Valves only where indicated on MFD's with notes.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and smaller - Socket Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1551E01E Seamless, To be supplied with 150mm straight after bend at both ends. Bend radius to be 3 x NPS The Supplier shall make provision for thinning during bending to meet the minimum wall thickness after
bending. The minimum thickness at the end tangents shall not be less than the pipe thickness.
1551W006 For use on Welding Caps, elliptical heads and flat surfaces.
1561B016 Shop Drill & Tap to ASME B1.20.1, 1/2" NPT for Pressure Instrument connections. Tapped Centrally. The threads shall be done in a Sasol approved shop facility. Threads shall conform to ASME B1.20.1
specification for thread form, taper, length & dia of thread. Tolerances on taper, lead & angle of thread shall conform to ASME B1.20.1 for NPT threads. All threads shall be N/C Machined. Supplier shall
conform to requirements from SP-50-13 for material certification, PMI, inspection & testing. PMI shall be in accordance with SP-90-23. 100% Thread Inspection shall be conducted by FW Instrument QC
personnel.
1561F00M SP. Blind thickness to comply with ASME B16.48- CL150. Other dimensions shall satisfy installation between BS4504 (EN 1092) PN16 flange.
1561L001 Flange drilling to ANSI B16.5, Flange to be supplied complete with matching backing ring per referenced standard. Nominal Bore shall be 25.4mm and Nominal Wall Thickness 14.3mm.
1561P000 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1561P00E Comptabile to ASME B16.47 Series B flanges Shall be manufactured from a single piece material, I.e. the handle or web shall be integral. The Supplier shall include Drawings with dimension details and
calculations for EC/Sasol approval. The blind shall be designed to the specified Class rating and
to withstand leak (pressure) test conditions as per design code.
USE 45° LATROLETS ONLY FOR FLARE CONNECTIONS. Use Full Bore Gate Valves only where indicated on MFD's with notes.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and smaller - Socket Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1561R008 Comptabile to ASME B16.47 Series B flanges Shall be manufactured from a single piece material, I.e. the handle or web shall be integral. The Supplier shall include Drawings with dimension details and
calculations for EC/Sasol approval. The blind shall be designed to the specified Class rating and
to withstand leak (pressure) test conditions as per design code.
1561W00F Flange to be supplied complete with matching backing ring per referenced standard. For details of Ball Joint Facing refer Sasol STDD-5027, Rev 5.
1561W01D Weld Neck Flange in accordance with BS 4504 (EN 1092), Raised Face Serrated Finish, 3.2-6.3 micro m.
1561W01E Weld Neck Flange in accordance with BS 4504 (EN 1092), Raised Face Serrated Finish, 3.2-6.3 micro m.
1576G002 Pegged 316SS with 98% pure graphite laminated on both sides. Construction: Expanded Graphite of 98% Purity, Laminated on both sides of a 0.1mm thick pegged 316 SS Sheet
1576G01L Teflon Gasket/ Nomex- Full length bolt isolating sleeve/ 2 sets high temp phenolic isolating washer + 2 sets steel washer. Type F- Corrosive Hydrocarbon (Max Temp 200°C)
1576G01X Teflon Gasket/ Nomex- Full length bolt isolating sleeve/ 2 sets high temp phenolic isolating washer + 2 sets steel washer. Type F- Corrosive Hydrocarbon (Max Temp 200°C)
1576G01Z Modified Teflon Gasket (with Glass Microspheres or Silica)/High Temp Full length bolt isolating sleeve/2 sets high temp isolating washer + 2 sets steel washers/Type F- Corrosive Hydrocarbon (Rated for
Max Temp 260ºC)
1592K000 1.6mm diameter wire. 304SS round bar. Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not acceptable unless solution heat treated after repairs.
1592K004 1.6mm diameter wire. 304SS round bar. Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not acceptable unless solution heat treated after repairs.
1592K005 1.6mm diameter wire. 304SS round bar. Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not acceptable unless solution heat treated after repairs.
1598C001 Malleable iron, Male NPT X Male hose Spud, Cadmium Plated Pipe Threads- NPT(Taper). ASME B.1.20.1. Standard: Evertite Code 11307 or approved alternative.
1598C007 Material- Brass Chicago Coupling. Water/Air service. Male NPT x Quick connector end. Consolidated pneumatic class C15120. Pipe Threads- NPT(Taper). ASME B.1.20.1.
USE 45° LATROLETS ONLY FOR FLARE CONNECTIONS. Use Full Bore Gate Valves only where indicated on MFD's with notes.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and smaller - Socket Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1541S003 0356234 Pipe PE API-5L-B SMLS 0.5 0.5 XS - - XS 26 - - SSSF
- 1541S003 0356234 Pipe PE API-5L-B SMLS 0.75 0.75 XS - - XS 26 - - SSSF
- 1541S003 0356234 Pipe PE API-5L-B SMLS 1 1 XS - - XS 26 - - SSSF
- 1541S001 0356234 Pipe BE API-5L-B SMLS 1.5 1.5 XS - - XS - - - SSSF
- 1541X001 0356649 Pipe BE API-5L-B ERW 2 2 STD - - STD - - - SSSF
- 1541X001 0356649 Pipe BE API-5L-B ERW 3 3 STD - - STD - - - SSSF
- 1541X001 0356649 Pipe BE API-5L-B ERW 4 4 STD - - STD - - - SSSF
- 1541X001 Pipe BE API-5L-B ERW 5 5 STD - - STD - - - SSSF
- 1541X001 0356649 Pipe BE API-5L-B ERW 6 6 STD - - STD - - - SSSF
- 1541X001 0356646 Pipe BE API-5L-B ERW 8 8 Sch 20 - - Sch 20 - - - SSSF
- 1541X001 0356646 Pipe BE API-5L-B ERW 10 10 Sch 20 - - Sch 20 - - - SSSF
- 1541X001 0356646 Pipe BE API-5L-B ERW 12 12 Sch 20 - - Sch 20 - - - SSSF
- 1541X001 0356645 Pipe BE API-5L-B ERW 14 14 Sch 10 - - Sch 10 - - - SSSF
- 1541X001 0356645 Pipe BE API-5L-B ERW 16 16 Sch 10 - - Sch 10 - - - SSSF
- 1541X001 0356645 Pipe BE API-5L-B ERW 18 18 Sch 10 - - Sch 10 - - - SSSF
- 1541X001 0356645 Pipe BE API-5L-B ERW 20 20 Sch 10 - - Sch 10 - - - SSSF
- 1541X001 0356649 Pipe BE API-5L-B ERW 22 22 STD - - STD - - - SSSF
- 1541X001 0356649 Pipe BE API-5L-B ERW 24 24 STD - - STD - - - SSSF
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
714 1512G00A 0115373 Gate SWE X FTE CL800 A105 WB F6/Stell Trm 0.5 1 - - - - - - - SSSF
- 1512C00N 0063273 Check lift SWE CL800 A105 WB F6/Stell Trm 0.75 1 - - - - - - - SSSF
- 1512D005 0062543 Globe SWE CL800 A105 WB F6/Stell Trm 0.75 1 - - - - - - - SSSF
- 1512G00B 0061782 Gate SWE CL800 A105 WB F6/Stell Trm 0.75 1 - - - - 101 - - SSSF
- 1512B00Y 1001553 Ball PE CL800 A105 316 Ball PTFE Firesafe (cw extensions) 1 1 - - - - 123 - - SSSF
781 1512G02D 0158303 Gate RF CL600 A105 WB F6/Stell Trm 1 1.5 - - - - 100 127 - SSFF
- 1512C01P 0351200 Check swing BE CL800 A105 BB F6/Stell Trm 1.5 1.5 XS - - XS - - - SSSF
- 1512D01J 0341200 Globe BE CL800 A105 WB F6/Stell Trm 1.5 1.5 XS - - XS - - - SSSF
- 1512G02C 0312600 Gate BE CL800 A105 WB F6/Stell Trm 1.5 1.5 XS - - XS - - - SSSF
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1511D00D Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1511F00A Category B Lug Type, Body A216-WCB, Seat BUNA-N, Disc CS with 304SS seating, Seating Weld Overlay with min thk of 1.6mm, Shaft- 304SS. Valve shall be supplied with Leverlock Positioning handle
to faciliate for valve to be locked in intermediate positions. Valve shall be rated for shut-off at 1035 kPa @ 60°C. Bolt Holes on Lug Pattern Shall be through drilled. Electrostatic feature. Valve Lever Lock
handle shall be furnished with a lockable device that accepts a purchaser-supplied lock to enable valve to be locked in positions. Supplier shall confirm that mating pipework bore will give adequate disc
swing clearance. (Pipe Schedules: 6"-Std, 8-12-S-20, 14-20-S-10, 24"-Std)
1511F00B Category B Lug Type, Body A216-WCB, Seat BUNA-N, Disc CS with 304SS seating, Seating Weld Overlay with min thk of 1.6mm, Shaft- 304SS. Valve shall be supplied with Leverlock Positioning handle
to faciliate for valve to be locked in intermediate positions. Valve shall be rated for shut-off at 1035 kPa @ 60°C. Bolt Holes on Lug Pattern Shall be through drilled. Electrostatic feature. Valve Lever Lock
handle shall be furnished with a lockable device that accepts a purchaser-supplied lock to enable valve to be locked in positions. Supplier shall confirm that mating pipework bore will give adequate disc
swing clearance. (Pipe Schedules: 6"-Std, 8-12-S-20, 14-20-S-10, 24"-Std)
1511G002 Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1511G003 Flanges >24" to match ASME B16.47, Series B Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler
1511G004 Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1511W00F Integral seating surfaces; Inconel-X spring; 316 SS Hinge pin / Stop pin / pin retainers / Lug bearings; Dual Plate Supplier shall confirm that mating pipework bore will give adequate disc swing clearance.
(Pipe Schedules: 6"-Std, 8-12-S-20, 14-20-S-10, 24"-Std)
1512B00Y Valves to comply with the requirements of BS 5351. Anti blow out stem. Fire safe to BS 6755-2. Floating ball. Valves to be supplied complete with 150mm long plain ended A106-B seamless (Sch 80)
extension pipe pups socket welded to the valves on both ends. Valve design shall be such that all parts can be easily serviced or replaced in-line. Standard body cavity pressure relief design.
1512D005 Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated. Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512D01J Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated.
1512G00B Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G02C Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G02D Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1551W006 For use on Welding Caps, elliptical heads and flat surfaces.
1561B016 Shop Drill & Tap to ASME B1.20.1, 1/2" NPT for Pressure Instrument connections. Tapped Centrally. The threads shall be done in a Sasol approved shop facility. Threads shall conform to ASME B1.20.1
specification for thread form, taper, length & dia of thread. Tolerances on taper, lead & angle of thread shall conform to ASME B1.20.1 for NPT threads. All threads shall be N/C Machined. Supplier shall
conform to requirements from SP-50-13 for material certification, PMI, inspection & testing. PMI shall be in accordance with SP-90-23. 100% Thread Inspection shall be conducted by FW Instrument QC
personnel.
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1561P000 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1561R000 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1561W00F Flange to be supplied complete with matching backing ring per referenced standard. For details of Ball Joint Facing refer Sasol STDD-5027, Rev 5.
1576G008 Nitrile or neoprene bound aramid fibre (cut from sheet). Use only for Hydrant valves and Monitors.
1576G01T Non metallic gasket/0.8mm fibreglass reinforced polyester sleeves/2sets reinforced phenolic + 2sets steel washers Type F - Non Corrosive service. Non metallic Insulating Gasket shall have following
properties: Dielectric strength (ASTM D149)- 21Kv/mm, Compressive strength (ASTM D625)- 340MPa, Max water absorption (ASTM D229)- 0.1%, Min & Max operating temp- (-17 to 93°C), Hardness
Rockwell M (ASTM D785)- 115, Shear strength (ASTM D732)- 150MPa.
1576G01U Non metallic gasket/0.8mm fibreglass reinforced polyester sleeves/2sets reinforced phenolic + 2sets steel washers Type F - Non Corrosive service. Non metallic Insulating Gasket shall have following
properties: Dielectric strength (ASTM D149)- 21Kv/mm, Compressive strength (ASTM D625)- 340MPa, Max water absorption (ASTM D229)- 0.1%, Min & Max operating temp- (-17 to 93°C), Hardness
Rockwell M (ASTM D785)- 115, Shear strength (ASTM D732)- 150MPa.
1576G01W Teflon Gasket/ Nomex- Full length bolt isolating sleeves/ 2 sets high temp phenolic isolating washer + 2 sets steel washer. Type E- Corrosive Hydrocarbon (Max Temp 200°C)
1576G022 THERMICULITE TANGED INSERT CL 150 THERMAL BARRIER, FULL FACE WITH BOLT HOLES, 6mm THICK COMPLETE WITH PHENOLIC FULL LENGTH BOLT SLEEVES, THERMICULITE 2mm
THICK WASHERS AND 2mm THICK STEEL WASHERS. Thermal Barrier to insulate flange sets operating at 230 and 60°C
1576G023 THERMICULITE TANGED INSERT CL 300 THERMAL BARRIER, FULL FACE WITH BOLT HOLES, 6mm THICK COMPLETE WITH PHENOLIC FULL LENGTH SLEEVES, THERMICULITE 2mm THICK
WASHERS AND 2mm THICK STEEL WASHERS. Thermal Barrier to insulate flange sets operating at 230 and 60°C.
1592K000 1.6mm diameter wire. 304SS round bar. Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not acceptable unless solution heat treated after repairs.
1598C007 Material- Brass Chicago Coupling. Water/Air service. Male NPT x Quick connector end. Consolidated pneumatic class C15120. Pipe Threads- NPT(Taper). ASME B.1.20.1.
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Pressure: 1960kPa 1960kPa 1920kPa 1770kPa 1580kPa 1380kPa 1210kPa 1020kPa 930kPa 840kPa 760kPa
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1541S003 0356234 Pipe PE API-5L-B SMLS 0.5 0.5 XS - - XS 310 26 - SSSF
- 1541S003 0356234 Pipe PE API-5L-B SMLS 0.75 0.75 XS - - XS 310 26 - SSSF
- 1541S003 0356234 Pipe PE API-5L-B SMLS 1 1 XS - - XS 310 26 - SSSF
- 1541S001 0356234 Pipe BE API-5L-B SMLS 1.5 1.5 XS - - XS 310 26 - SSSF
- 1541S001 0356234 Pipe BE API-5L-B SMLS 2 2 XS - - XS 310 26 - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 3 3 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 4 4 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 6 6 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 8 8 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 10 10 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 12 12 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 14 14 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 16 16 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 18 18 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 20 20 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 22 22 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 24 24 STD - - STD - - - SSSF
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1512G00B 0061782 Gate SWE CL800 A105 WB F6/Stell Trm 0.5 1 - - - - 101 26 - SSSF
714 1512G00A 0115373 Gate SWE X FTE CL800 A105 WB F6/Stell Trm 0.5 1.5 - - - - 102 - - SSSF
- 1512C00N 0063273 Check lift SWE CL800 A105 WB F6/Stell Trm 0.75 1 - - - - - - - SSSF
- 1512D005 0062543 Globe SWE CL800 A105 WB F6/Stell Trm 0.75 1 - - - - - - - SSSF
- 1512P00A 0113542 Plug SWE CL300 A105 Lubricated 316SS Trm WO 0.75 1 - - - - - - - SSSF
- 1512B015 1001290 Ball PE CL300 A105 316 Ball RPTFE WO (cw extensions) 200 0.75 1.5 - - - - - - - SSSF
781 1512G00D 0158303 Gate RF CL600 A105 WB F6/Stell Trm Graph Pack 1 1.5 - - - - 100 127 - SSFF
- 1512C01P 0351200 Check swing BE CL800 A105 BB F6/Stell Trm 1.5 1.5 XS - - XS - - - SSSF
- 1512D01J 0341200 Globe BE CL800 A105 WB F6/Stell Trm 1.5 1.5 XS - - XS - - - SSSF
- 1512G02C 0312600 Gate BE CL800 A105 WB F6/Stell Trm 1.5 1.5 XS - - XS - - - SSSF
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1511B00H Anti-Blowout stem, Firesafe design to API 607, Valves to comply with API-608
1511C02A Integral seating surfaces, Inconel-X spring, 316SS hinge pin / stop pin / pin retainers / lug bearings API-594:-Type A, Dual Plate Double Flanged Check Valve
1511D00D Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1511G002 Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1511G003 Flanges >24" to match ASME B16.47, Series B Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler
1511G004 Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1511P00H Hyperseal, Short pattern, Valve shall be furnished with Formula No 421 sealant.
1511P00J Hyperseal, Short pattern, Valve shall be furnished with Formula No 421 sealant.
1511P00L Venturi Pattern, Valve shall be furnished with Formula No 421 sealant or equivalent.
1512B015 R-PTFE seats & seals, Anti-Blowout stem, Firesafe, Split Body, Floating Ball. Valves to be supplied with 150mm long plain ended A106-B seamless S-160 extension pipe pups SW to the valves on both
ends. Valve shall be Heat Treated after all welding is completed.
1512D005 Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated. Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512D01J Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated.
1512G00B Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1512G02C Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512P00A Short Pattern, Screwed Gland, Valve shall be furnished with Formula No 421 sealant or equivalent.
1561B016 Shop Drill & Tap to ASME B1.20.1, 1/2" NPT for Pressure Instrument connections. Tapped Centrally. The threads shall be done in a Sasol approved shop facility. Threads shall conform to ASME B1.20.1
specification for thread form, taper, length & dia of thread. Tolerances on taper, lead & angle of thread shall conform to ASME B1.20.1 for NPT threads. All threads shall be N/C Machined. Supplier shall
conform to requirements from SP-50-13 for material certification, PMI, inspection & testing. PMI shall be in accordance with SP-90-23. 100% Thread Inspection shall be conducted by FW Instrument QC
personnel.
1561L001 Flange drilling to ANSI B16.5, Flange to be supplied complete with matching backing ring per referenced standard. Nominal Bore shall be 25.4mm and Nominal Wall Thickness 14.3mm.
1561P000 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1561R000 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1561W00F Flange to be supplied complete with matching backing ring per referenced standard. For details of Ball Joint Facing refer Sasol STDD-5027, Rev 5.
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Pressure: 1960kPa 1960kPa 1920kPa 1770kPa 1580kPa 1380kPa 1210kPa 1020kPa 930kPa 840kPa 740kPa 650kPa
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1541S003 0356234 Pipe PE API-5L-B SMLS 0.5 0.5 XS - - XS - - - SSSF
- 1541S003 0356234 Pipe PE API-5L-B SMLS 0.75 0.75 XS - - XS - - - SSSF
- 1541S003 0356234 Pipe PE API-5L-B SMLS 1 1 XS - - XS - - - SSSF
- 1541S001 0356234 Pipe BE API-5L-B SMLS 1.5 1.5 XS - - XS - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 2 2 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 3 3 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 4 4 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 6 6 STD - - STD - - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 8 8 Sch 20 - - Sch 20 - - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 10 10 Sch 20 - - Sch 20 - - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 12 12 Sch 20 - - Sch 20 - - - SSSF
- 1541S001 0356227 Pipe BE API-5L-B SMLS 14 14 Sch 10 - - Sch 10 - - - SSSF
- 1541S001 0356227 Pipe BE API-5L-B SMLS 16 16 Sch 10 - - Sch 10 - - - SSSF
- 1541S001 0356227 Pipe BE API-5L-B SMLS 18 18 Sch 10 - - Sch 10 - - - SSSF
- 1541S001 0356227 Pipe BE API-5L-B SMLS 20 20 Sch 10 - - Sch 10 - - - SSSF
- 1541S001 0356227 Pipe BE API-5L-B SMLS 22 22 Sch 10 - - Sch 10 - - - SSSF
- 1541S001 0356227 Pipe BE API-5L-B SMLS 24 24 Sch 10 - - Sch 10 - - - SSSF
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1512C00N 0063273 Check lift SWE CL800 A105 WB F6/Stell Trm 0.5 1 - - - - 26 - - SSSF
- 1512D005 0062543 Globe SWE CL800 A105 WB F6/Stell Trm 0.5 1 - - - - 26 - - SSSF
- 1512G00B 0061782 Gate SWE CL800 A105 WB F6/Stell Trm 0.5 1 - - - - 101 191 - SSSF
714 1512G00A 0115373 Gate SWE X FTE CL800 A105 WB F6/Stell Trm 0.5 1.5 - - - - 26 102 181 SSSF
781 1512G00D 0158303 Gate RF CL600 A105 WB F6/Stell Trm Graph Pack 1 1.5 - - - - 100 127 - SSFF
- 1512C01P 0351200 Check swing BE CL800 A105 BB F6/Stell Trm 1.5 1.5 XS - - XS - - - SSSF
- 1512D01J 0341200 Globe BE CL800 A105 WB F6/Stell Trm 1.5 1.5 XS - - XS - - - SSSF
- 1512G02C 0312600 Gate BE CL800 A105 WB F6/Stell Trm 1.5 1.5 XS - - XS 101 - - SSSF
- 1511C020 0163450 Check swing RF CL150 A216-WCB BB F6 Trm 2 4 - - - - - - - SSFF
773 1511G004 0156860 Gate RF CL300 A216-WCB BB F6 Trm 2 4 - - - - 102 - - SSFF
Ammonia Water Service not included. Use Spray Shields for Caustic Service. All Flanged Joints, including Valve Bonnets, shall be fitted with Indicating Spray
Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid Service (Milsheff or equivalent). DO
NOT USE FOR SMALL BORE CAUSTIC SODA SERVICE (½" TO 1½": USE LINE CLASS CAF)
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and smaller - Socket Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Ammonia Water Service not included. Use Spray Shields for Caustic Service. All Flanged Joints, including Valve Bonnets, shall be fitted with Indicating Spray
Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid Service (Milsheff or equivalent). DO
NOT USE FOR SMALL BORE CAUSTIC SODA SERVICE (½" TO 1½": USE LINE CLASS CAF)
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and smaller - Socket Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Ammonia Water Service not included. Use Spray Shields for Caustic Service. All Flanged Joints, including Valve Bonnets, shall be fitted with Indicating Spray
Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid Service (Milsheff or equivalent). DO
NOT USE FOR SMALL BORE CAUSTIC SODA SERVICE (½" TO 1½": USE LINE CLASS CAF)
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and smaller - Socket Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Ammonia Water Service not included. Use Spray Shields for Caustic Service. All Flanged Joints, including Valve Bonnets, shall be fitted with Indicating Spray
Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid Service (Milsheff or equivalent). DO
NOT USE FOR SMALL BORE CAUSTIC SODA SERVICE (½" TO 1½": USE LINE CLASS CAF)
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and smaller - Socket Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Ammonia Water Service not included. Use Spray Shields for Caustic Service. All Flanged Joints, including Valve Bonnets, shall be fitted with Indicating Spray
Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid Service (Milsheff or equivalent). DO
NOT USE FOR SMALL BORE CAUSTIC SODA SERVICE (½" TO 1½": USE LINE CLASS CAF)
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and smaller - Socket Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1511C02A Integral seating surfaces, Inconel-X spring, 316SS hinge pin / stop pin / pin retainers / lug bearings API-594:-Type A, Dual Plate Double Flanged Check Valve
1511D00D Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1511G002 Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1511G003 Flanges >24" to match ASME B16.47, Series B Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler
1511G004 Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1512D005 Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated. Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512D01J Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated.
1512G00B Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G00D Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G02C Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1561B016 Shop Drill & Tap to ASME B1.20.1, 1/2" NPT for Pressure Instrument connections. Tapped Centrally. The threads shall be done in a Sasol approved shop facility. Threads shall conform to ASME B1.20.1
specification for thread form, taper, length & dia of thread. Tolerances on taper, lead & angle of thread shall conform to ASME B1.20.1 for NPT threads. All threads shall be N/C Machined. Supplier shall
conform to requirements from SP-50-13 for material certification, PMI, inspection & testing. PMI shall be in accordance with SP-90-23. 100% Thread Inspection shall be conducted by FW Instrument QC
personnel.
Ammonia Water Service not included. Use Spray Shields for Caustic Service. All Flanged Joints, including Valve Bonnets, shall be fitted with Indicating Spray
Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid Service (Milsheff or equivalent). DO
NOT USE FOR SMALL BORE CAUSTIC SODA SERVICE (½" TO 1½": USE LINE CLASS CAF)
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and smaller - Socket Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1561L001 Flange drilling to ANSI B16.5, Flange to be supplied complete with matching backing ring per referenced standard. Nominal Bore shall be 25.4mm and Nominal Wall Thickness 14.3mm.
1561P000 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1561R000 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1592K000 1.6mm diameter wire. 304SS round bar. Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not acceptable unless solution heat treated after repairs.
1592K004 1.6mm diameter wire. 304SS round bar. Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not acceptable unless solution heat treated after repairs.
Ammonia Water Service not included. Use Spray Shields for Caustic Service. All Flanged Joints, including Valve Bonnets, shall be fitted with Indicating Spray
Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid Service (Milsheff or equivalent). DO
NOT USE FOR SMALL BORE CAUSTIC SODA SERVICE (½" TO 1½": USE LINE CLASS CAF)
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and smaller - Socket Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Pressure: 1960kPa 1960kPa 1920kPa 1770kPa 1580kPa 1380kPa 1210kPa 1020kPa 930kPa 840kPa 740kPa 650kPa
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1541S003 0356234 Pipe PE API-5L-B SMLS 0.5 0.5 XS - - XS - - - SSSF
- 1541S003 0356234 Pipe PE API-5L-B SMLS 0.75 0.75 XS - - XS - - - SSSF
- 1541S003 0356234 Pipe PE API-5L-B SMLS 1 1 XS - - XS - - - SSSF
- 1541S001 0356234 Pipe BE API-5L-B SMLS 1.5 1.5 XS - - XS - - - SSSF
- 1541S001 0356234 Pipe BE API-5L-B SMLS 2 2 XS - - XS - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 3 3 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 4 4 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 6 6 STD - - STD - - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 8 8 Sch 20 - - Sch 20 - - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 10 10 Sch 20 - - Sch 20 - - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 12 12 Sch 20 - - Sch 20 - - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 14 14 Sch 20 - - Sch 20 - - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 16 16 Sch 20 - - Sch 20 - - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 18 18 Sch 20 - - Sch 20 - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 20 20 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 22 22 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 24 24 STD - - STD - - - SSSF
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1512B01C 1001704 Ball Shrt RF CL300 A105 316SS Fl ball RPTFE WO FB 0.5 0.5 - - - - 833 721 - SSFF
- 1512C00L 0063269 Check lift SWE CL800 A105 F6/Stell Trm No Cop 0.5 1 - - - - 159 - - SSSF
- 1512G017 0061807 Gate SWE CL800 A105 WB F6/Stell Trm No Cop 0.5 1 - - - - 159 101 - SSSF
714 1512G016 0115258 Gate SWE X FTE CL800 A105 WB F6/Stell Trm No Cop 0.5 1.5 - - - - 159 102 - SSSF
- 1512D00M 0062524 Globe SWE CL800 A105 WB F6/Stell Trm No Cop 0.75 1 - - - - 159 - - SSSF
781 1512D01T 1001426 Globe RF CL600 A105 WB F6/Stell Trm No Cop 0.75 1.5 - - - - 721 - - SSFF
1190 1511B019 1001427 Ball Shrt RF CL300 A105 316SS Fl ball RPTFE WO FB 200 1 1.5 - - - - 9 - - SSFF
781 1512G00E 0169477 Gate RF CL600 A105 BB F6/Stell Trm No Cop 1 1.5 - - - - 159 100 127 SSFF
- 1512C024 0314510 Check swing BE CL800 A105 F6/Stell Trm No Cop 1.5 1.5 XS - - XS 159 - - SSSF
- 1512D01S 0313010 Globe BE CL800 A105 WB F6/Stell Trm No Cop 1.5 1.5 XS - - XS 159 - - SSSF
Isopropyl Ether service not included. ++ Mandatory PWHT for lines exposed to carbonate solutions, mixtures of carbonates & hydrocarbons when the operating
temperature exceeds 20 deg C.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 3.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Isopropyl Ether service not included. ++ Mandatory PWHT for lines exposed to carbonate solutions, mixtures of carbonates & hydrocarbons when the operating
temperature exceeds 20 deg C.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 3.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Isopropyl Ether service not included. ++ Mandatory PWHT for lines exposed to carbonate solutions, mixtures of carbonates & hydrocarbons when the operating
temperature exceeds 20 deg C.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 3.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Isopropyl Ether service not included. ++ Mandatory PWHT for lines exposed to carbonate solutions, mixtures of carbonates & hydrocarbons when the operating
temperature exceeds 20 deg C.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 3.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Isopropyl Ether service not included. ++ Mandatory PWHT for lines exposed to carbonate solutions, mixtures of carbonates & hydrocarbons when the operating
temperature exceeds 20 deg C.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 3.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Isopropyl Ether service not included. ++ Mandatory PWHT for lines exposed to carbonate solutions, mixtures of carbonates & hydrocarbons when the operating
temperature exceeds 20 deg C.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 3.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1511B017 Valve in carbonate service. Floating Ball, FB,Top Entry, Anti-Blowout stem, firesafe design, Valves to comply with API-608. Valves with repair welds are not acceptable unless PWHT. No copper or copper
bearing alloys permitted. Anti-static design. Standard body cavity pressure relief design.
1511B019 Valve in carbonate service. Floating Ball, FB,Top Entry, Anti-Blowout stem, firesafe design, Valves to comply with API-608 Valve in carbonate service. Valves with repair welds are not acceptable unless
PWHT. No copper or copper bearing alloys permitted. Anti-static design. Standard body cavity pressure relief design.
1511B01C Valves in carbonate service. Floating Ball, FB, Top Entry, Anti-Blowout stem, firesafe design, Valves to comply with API-608. Valves with repair welds are not acceptable unless PWHT. No copper or coppe
bearing alloys permitted. Anti-static design. Standard body cavity pressure relief design.
1511C02B Integral seating surfaces, Inconel-X spring, 316SS hinge pin/stop pin/pin retainer/lug bearing. No copper or copper bearing alloys permitted. API-594:-Type A, Dual Plate Double Flanged Check Valve.
Valves with repair welds are not acceptable unless PWHT.
1511G00A No Copper or copper bearing alloys permitted. Stem Packing- Compressed graphite rings, Bonnet Gasket- SS Reinforced Graphite. For Sour Water/Gas service.
Isopropyl Ether service not included. ++ Mandatory PWHT for lines exposed to carbonate solutions, mixtures of carbonates & hydrocarbons when the operating
temperature exceeds 20 deg C.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 3.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1511G03R No Copper or copper bearing alloys permitted Stem Packing- Compressed graphite rings, Bonnet Gasket- SS Reinforced Graphite. For Sour Water/Gas service.
1512B01C Floating Ball, Full Bore, Top Entry, Anti-Blowout stem, firesafe design, Valves to comply with API-608 Valve seats and seals shall be rated for the same pressue-temperature rating as of the shell, to ASME
B16.34
1551E00E To be supplied with 75mm straight after bend at both ends.Bend radius to be 5 x NPS. Seamless. The Supplier shall make provision for thinning during bending to meet the minimum wall thickness after
bending. The minimum thickness at the end tangents shall not be less than the pipe thickness.
1551E00F To be supplied with 75mm straight after bend at both ends. Bend radius to be 5 X pipe OD (NPS) in inches (e.g. 6" therefore to have a radius of 762mm). Seamless. The Supplier shall make provision for
thinning during bending to meet the minimum wall thickness after bending. The minimum thickness at the end tangents shall not be less than the pipe thickness.
1551E01C Seamless, To be supplied with 150mm straight after bend at both ends. Bend radius to be 5 x NPS The Supplier shall make provision for thinning during bending to meet the minimum wall thickness after
bending. The minimum thickness at the end tangents shall not be less than the pipe thickness.
1551E01D Seamless, To be supplied with 150mm straight after bend at both ends. Bend radius to be 5 x NPS The Supplier shall make provision for thinning during bending to meet the minimum wall thickness after
bending. The minimum thickness at the end tangents shall not be less than the pipe thickness.
Isopropyl Ether service not included. ++ Mandatory PWHT for lines exposed to carbonate solutions, mixtures of carbonates & hydrocarbons when the operating
temperature exceeds 20 deg C.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 3.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1561L001 Flange drilling to ANSI B16.5, Flange to be supplied complete with matching backing ring per referenced standard. Nominal Bore shall be 25.4mm and Nominal Wall Thickness 14.3mm.
1561P000 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1561R000 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1576G002 Pegged 316SS with 98% pure graphite laminated on both sides. Construction: Expanded Graphite of 98% Purity, Laminated on both sides of a 0.1mm thick pegged 316 SS Sheet
1576G01L Teflon Gasket/ Nomex- Full length bolt isolating sleeve/ 2 sets high temp phenolic isolating washer + 2 sets steel washer. Type F- Corrosive Hydrocarbon (Max Temp 200°C)
1592K000 1.6mm diameter wire. 304SS round bar. Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not acceptable unless solution heat treated after repairs.
1598C007 Material- Brass Chicago Coupling. Water/Air service. Male NPT x Quick connector end. Consolidated pneumatic class C15120. Pipe Threads- NPT(Taper). ASME B.1.20.1.
Isopropyl Ether service not included. ++ Mandatory PWHT for lines exposed to carbonate solutions, mixtures of carbonates & hydrocarbons when the operating
temperature exceeds 20 deg C.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 3.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1541S001 0356233 Pipe BE API-5L-B SMLS 0.5 0.5 XS - - XS - - - SSSF
- 1541S001 0356233 Pipe BE API-5L-B SMLS 0.75 0.75 XS - - XS - - - SSSF
- 1541S001 0356234 Pipe BE API-5L-B SMLS 1 1 XS - - XS - - - SSSF
- 1541S001 0356234 Pipe BE API-5L-B SMLS 1.5 1.5 XS - - XS - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 2 2 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 3 3 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 4 4 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 6 6 STD - - STD - - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 8 8 Sch 20 - - Sch 20 - - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 10 10 Sch 20 - - Sch 20 - - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 12 12 Sch 20 - - Sch 20 - - - SSSF
- 1541S001 0356227 Pipe BE API-5L-B SMLS 14 14 Sch 10 - - Sch 10 - - - SSSF
- 1541S001 0356227 Pipe BE API-5L-B SMLS 16 16 Sch 10 - - Sch 10 - - - SSSF
- 1541S001 0356227 Pipe BE API-5L-B SMLS 18 18 Sch 10 - - Sch 10 - - - SSSF
- 1541S001 0356227 Pipe BE API-5L-B SMLS 20 20 Sch 10 - - Sch 10 - - - SSSF
- 1541S001 0356227 Pipe BE API-5L-B SMLS 22 22 Sch 10 - - Sch 10 - - - SSSF
- 1541S001 0356227 Pipe BE API-5L-B SMLS 24 24 Sch 10 - - Sch 10 - - - SSSF
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1512C01V 0164723 Check lift RF CL600 A105 BB 316 Trm Horiz 1 1.5 - - - - - - - SSFF
- 1512D008 0161733 Globe RF CL600 A105 BB 316 Trm 1 1.5 - - - - 106 - - SSFF
- 1512P009 0295896 Plug Shrt RF CL300 A105 Lubricated 316SS Trm WO 1 1.5 - - - - 100 127 - SSFF
- 1511C025 0163650 Check swing RF CL150 A216-WCB BB 316 Trm 2 4 - - - - - - - SSFF
- 1511D02Q 0160661 Globe RF CL150 A216-WCB BB 316 Trm 2 8 - - - - - - - SSFF
- 1511P00H 0296100 Plug Shrt RF CL150 A216-WCB Lubricated 316SS Trm WO 2 8 - - - - 630 - - SSFF
- 1511W000 0280758 Check Wafer RFTBE CL150 A216-WCB 316 Trm SPLT 6 24 - - - - - - - SSFF
- 1511P00J 0296102 Plug Shrt RF CL150 A216-WCB Lubricated 316SS Trm GO 10 12 - - - - 630 - - SSFF
Use Spary Shields for Caustic Service. All Flanged Joints, including Valve Bonnets, shall be fitted with Indicating Spray Shields. Spray Shield material shall be
Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid Service (Milsheff or equivalent)
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and larger - Butt Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Use Spary Shields for Caustic Service. All Flanged Joints, including Valve Bonnets, shall be fitted with Indicating Spray Shields. Spray Shield material shall be
Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid Service (Milsheff or equivalent)
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and larger - Butt Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Use Spary Shields for Caustic Service. All Flanged Joints, including Valve Bonnets, shall be fitted with Indicating Spray Shields. Spray Shield material shall be
Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid Service (Milsheff or equivalent)
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and larger - Butt Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Use Spary Shields for Caustic Service. All Flanged Joints, including Valve Bonnets, shall be fitted with Indicating Spray Shields. Spray Shield material shall be
Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid Service (Milsheff or equivalent)
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and larger - Butt Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1511P00J Hyperseal, Short pattern, Valve shall be furnished with Formula No 421 sealant.
1511W000 Integral seating surfaces; Inconel-X spring; 316 SS Hinge pin / Stop pin / pin retainers / Lug bearings; Single Plate Supplier shall confirm that mating pipework bore will give adequate disc swing clearance.
(Pipe Schedules: 6"-Std, 8-12-S-20, 14-24-S-10)
Use Spary Shields for Caustic Service. All Flanged Joints, including Valve Bonnets, shall be fitted with Indicating Spray Shields. Spray Shield material shall be
Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid Service (Milsheff or equivalent)
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and larger - Butt Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1561B016 Shop Drill & Tap to ASME B1.20.1, 1/2" NPT for Pressure Instrument connections. Tapped Centrally. The threads shall be done in a Sasol approved shop facility. Threads shall conform to ASME B1.20.1
specification for thread form, taper, length & dia of thread. Tolerances on taper, lead & angle of thread shall conform to ASME B1.20.1 for NPT threads. All threads shall be N/C Machined. Supplier shall
conform to requirements from SP-50-13 for material certification, PMI, inspection & testing. PMI shall be in accordance with SP-90-23. 100% Thread Inspection shall be conducted by FW Instrument QC
personnel.
1561L001 Flange drilling to ANSI B16.5, Flange to be supplied complete with matching backing ring per referenced standard. Nominal Bore shall be 25.4mm and Nominal Wall Thickness 14.3mm.
1561P000 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1561R000 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1576G005 Bi-axial expanded PTFE with mineral fillers & silicon oxide filler
1576G006 Bi-axial expanded PTFE with mineral fillers & silicon oxide filler
1592K000 1.6mm diameter wire. 304SS round bar. Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not acceptable unless solution heat treated after repairs.
Use Spary Shields for Caustic Service. All Flanged Joints, including Valve Bonnets, shall be fitted with Indicating Spray Shields. Spray Shield material shall be
Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid Service (Milsheff or equivalent)
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and larger - Butt Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Pressure: 1960kPa 1960kPa 1920kPa 1770kPa 1580kPa 1380kPa 1210kPa 1020kPa 930kPa 840kPa 740kPa 650kPa
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1541S003 0356234 Pipe PE API-5L-B SMLS 0.5 0.5 XS - - XS - - - SSSF
- 1541S003 0356234 Pipe PE API-5L-B SMLS 0.75 0.75 XS - - XS - - - SSSF
- 1541S003 0356234 Pipe PE API-5L-B SMLS 1 1 XS - - XS - - - SSSF
- 1541S001 0356234 Pipe BE API-5L-B SMLS 1.5 1.5 XS - - XS - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 2 2 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 3 3 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 4 4 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 6 6 STD - - STD - - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 8 8 Sch 20 - - Sch 20 - - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 10 10 Sch 20 - - Sch 20 - - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 12 12 Sch 20 - - Sch 20 - - - SSSF
- 1541S001 0356227 Pipe BE API-5L-B SMLS 14 14 Sch 10 - - Sch 10 - - - SSSF
- 1541S001 0356227 Pipe BE API-5L-B SMLS 16 16 Sch 10 - - Sch 10 - - - SSSF
- 1541S001 0356227 Pipe BE API-5L-B SMLS 18 18 Sch 10 - - Sch 10 - - - SSSF
- 1541S001 0356227 Pipe BE API-5L-B SMLS 20 20 Sch 10 - - Sch 10 - - - SSSF
- 1541S001 0356227 Pipe BE API-5L-B SMLS 22 22 Sch 10 - - Sch 10 - - - SSSF
- 1541S001 0356227 Pipe BE API-5L-B SMLS 24 24 Sch 10 - - Sch 10 - - - SSSF
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1512D005 0062543 Globe SWE CL800 A105 WB F6/Stell Trm 0.5 1 - - - - - - - SSSF
- 1512G00B 0061782 Gate SWE CL800 A105 WB F6/Stell Trm 0.5 1 - - - - 101 - - SSSF
714 1512G00A 0115373 Gate SWE X FTE CL800 A105 WB F6/Stell Trm 0.5 1.5 - - - - 102 - - SSSF
- 1512C00N 0063273 Check lift SWE CL800 A105 WB F6/Stell Trm 0.75 1 - - - - - - - SSSF
781 1512G02D 0158303 Gate RF CL600 A105 WB F6/Stell Trm 1 1.5 - - - - 100 127 - SSFF
- 1512C01P 0351200 Check swing BE CL800 A105 BB F6/Stell Trm 1.5 1.5 XS - - XS - - - SSSF
- 1512D01J 0341200 Globe BE CL800 A105 WB F6/Stell Trm 1.5 1.5 XS - - XS - - - SSSF
- 1512G02C 0312600 Gate BE CL800 A105 WB F6/Stell Trm 1.5 1.5 XS - - XS 101 - - SSSF
- 1511C020 0163450 Check swing RF CL150 A216-WCB BB F6 Trm 2 4 - - - - - - - SSFF
- 1511D00D 0160461 Globe RF CL150 A216-WCB BB F6/Stell Trm 2 8 - - - - - - - SSFF
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1511C02A Integral seating surfaces, Inconel-X spring, 316SS hinge pin / stop pin / pin retainers / lug bearings API-594:-Type A, Dual Plate Double Flanged Check Valve
1511D00D Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1511G002 Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1511G003 Flanges >24" to match ASME B16.47, Series B Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler
1512D005 Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated. Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512D01J Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated.
1512G00B Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G02C Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G02D Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1561B016 Shop Drill & Tap to ASME B1.20.1, 1/2" NPT for Pressure Instrument connections. Tapped Centrally. The threads shall be done in a Sasol approved shop facility. Threads shall conform to ASME B1.20.1
specification for thread form, taper, length & dia of thread. Tolerances on taper, lead & angle of thread shall conform to ASME B1.20.1 for NPT threads. All threads shall be N/C Machined. Supplier shall
conform to requirements from SP-50-13 for material certification, PMI, inspection & testing. PMI shall be in accordance with SP-90-23. 100% Thread Inspection shall be conducted by FW Instrument QC
personnel.
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1561P000 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1561R000 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1561W00F Flange to be supplied complete with matching backing ring per referenced standard. For details of Ball Joint Facing refer Sasol STDD-5027, Rev 5.
1592K000 1.6mm diameter wire. 304SS round bar. Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not acceptable unless solution heat treated after repairs.
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Pressure: 1590kPa 1590kPa 1530kPa 1330kPa 1200kPa 1120kPa 1050kPa 1000kPa 930kPa 840kPa 740kPa 650kPa 550kPa
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1543S007 0364086 Pipe PE A312-TP304L SMLS 0.5 0.5 Sch 40S - - Sch 40S 310 - - SSSF
- 1543S007 0364086 Pipe PE A312-TP304L SMLS 0.75 0.75 Sch 40S - - Sch 40S 310 - - SSSF
- 1543S007 0364086 Pipe PE A312-TP304L SMLS 1 1 Sch 40S - - Sch 40S 310 - - SSSF
- 1543S007 0364086 Pipe PE A312-TP304L SMLS 1.125 1.125 Sch 40S - - Sch 40S 310 - - SSSF
- 1543S007 0364086 Pipe PE A312-TP304L SMLS 1.25 1.25 Sch 40S - - Sch 40S 310 - - SSSF
- 1543S004 0364086 Pipe BE A312-TP304L SMLS 1.5 1.5 Sch 40S - - Sch 40S - - - SSSF
- 1543W001 0364151 Pipe BE A312-TP304L EFW 2 2 Sch 10S* - - Sch 10S* 217 - - SSSF F3
- 1543W001 0364151 Pipe BE A312-TP304L EFW 2.5 2.5 Sch 10S* - - Sch 10S* 217 - - SSSF F3
- 1543W001 0364151 Pipe BE A312-TP304L EFW 3 3 Sch 10S* - - Sch 10S* 217 - - SSSF F3
- 1543W001 0364151 Pipe BE A312-TP304L EFW 4 4 Sch 10S* - - Sch 10S* 217 - - SSSF F3
- 1543W001 0364151 Pipe BE A312-TP304L EFW 6 6 Sch 10S* - - Sch 10S* 217 - - SSSF F3
- 1543W001 0364151 Pipe BE A312-TP304L EFW 8 8 Sch 10S* - - Sch 10S* 217 - - SSSF F3
- 1543W001 0364151 Pipe BE A312-TP304L EFW 10 10 Sch 10S* - - Sch 10S* 217 - - SSSF F3
- 1543W001 0364151 Pipe BE A312-TP304L EFW 12 12 Sch 10S* - - Sch 10S* 217 - - SSSF F3
- 1543W003 0364207 Pipe BE A358-304L EFW (Cl 1 or Cl 4) 14 14 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W003 0364207 Pipe BE A358-304L EFW (Cl 1 or Cl 4) 16 16 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W003 0364207 Pipe BE A358-304L EFW (Cl 1 or Cl 4) 18 18 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W003 0364207 Pipe BE A358-304L EFW (Cl 1 or Cl 4) 20 20 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W003 0364207 Pipe BE A358-304L EFW (Cl 1 or Cl 4) 22 22 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W003 0364207 Pipe BE A358-304L EFW (Cl 1 or Cl 4) 24 24 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W003 0364196 Pipe BE A358-304L EFW (Cl 1 or Cl 4) 30 30 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W003 0364196 Pipe BE A358-304L EFW (Cl 1 or Cl 4) 32 32 Sch 10* - - Sch 10* 217 - - SSSF
- 1543W003 0364196 Pipe BE A358-304L EFW (Cl 1 or Cl 4) 34 34 Sch 10* - - Sch 10* 217 - - SSSF
- 1543W003 0364196 Pipe BE A358-304L EFW (Cl 1 or Cl 4) 36 36 Sch 10* - - Sch 10* 217 - - SSSF
- 1543W003 0364213 Pipe BE A358-304L EFW (Cl 1 or Cl 4) 38 38 STD* - - STD* 217 - - SSSF
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1516C00H 0095448 Check lift SWE CL800 A182-F304L 304 Trm Horiz 0.5 1 - - - - - - - SSSF
- 1516D00E 0095468 Globe SWE CL800 A182-F304L WB 304 Trm 0.5 1 - - - - - - - SSSF
* Wall thickness is to be calculated based on individual design conditions. All Flanged Joints, including Valve Bonnets, in FEN service, shall be fitted with
Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Indicating Type for Nitric Acid Service (Milsheff or equivalent). Use
"CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 304L SS CL150 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
* Wall thickness is to be calculated based on individual design conditions. All Flanged Joints, including Valve Bonnets, in FEN service, shall be fitted with
Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Indicating Type for Nitric Acid Service (Milsheff or equivalent). Use
"CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 304L SS CL150 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
* Wall thickness is to be calculated based on individual design conditions. All Flanged Joints, including Valve Bonnets, in FEN service, shall be fitted with
Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Indicating Type for Nitric Acid Service (Milsheff or equivalent). Use
"CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 304L SS CL150 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
* Wall thickness is to be calculated based on individual design conditions. All Flanged Joints, including Valve Bonnets, in FEN service, shall be fitted with
Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Indicating Type for Nitric Acid Service (Milsheff or equivalent). Use
"CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 304L SS CL150 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
* Wall thickness is to be calculated based on individual design conditions. All Flanged Joints, including Valve Bonnets, in FEN service, shall be fitted with
Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Indicating Type for Nitric Acid Service (Milsheff or equivalent). Use
"CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 304L SS CL150 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
* Wall thickness is to be calculated based on individual design conditions. All Flanged Joints, including Valve Bonnets, in FEN service, shall be fitted with
Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Indicating Type for Nitric Acid Service (Milsheff or equivalent). Use
"CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 304L SS CL150 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
1515B00E Valve in carbonate service. Floating Ball, FB,Top Entry, Anti-Blowout stem, firesafe design, Valves to comply with API-608. Valves with repair welds are not acceptable unless solution treated after repairs.
No copper or copper bearing alloys permitted. Anti-static design. Standard body cavity pressure relief design. Valve seats and seals shall be rated for the same pressue-temperature rating as of the shell, t
ASME B16.34
1515B00F Valve in Carbonate service, Floating Ball, Full Bore, Top entry, Anti-blowout stem, Firesafe Valves with repair welds are not acceptable unless solution treated after repairs. No copper or copper bearing
alloys permitted. Anti-static design. Standard body cavity pressure relief design. Valve seats and seals shall be rated for the same pressue-temperature rating as of the shell, to ASME B16.34. Valve to
comply wit API-608.
1515C00Z Integral seating surfaces, Inconel-X750 spring, 316SS hinge pin/stop pin/pin retainers/lug bearings API-594:-Type A, Dual Plate Double Flanged Check Valve
1515D004 Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler. Globe valve Seat design to conform to API 602 paragraph 5.6.3
unless otherwise stated.
1515G006 Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
* Wall thickness is to be calculated based on individual design conditions. All Flanged Joints, including Valve Bonnets, in FEN service, shall be fitted with
Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Indicating Type for Nitric Acid Service (Milsheff or equivalent). Use
"CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 304L SS CL150 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
1515G00R Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1516B012 Valve in carbonate service. Floating Ball, FB,Top Entry, Anti-Blowout stem, firesafe design, Valves to comply with API-608 Valves with repair welds are not acceptable unless solution treated after repairs.
No copper or copper bearing alloys permitted. Anti-static design. Standard body cavity pressure relief design. Valve seats and seals shall be rated for the same pressue-temperature rating as of the shell, t
ASME B16.34
1516D003 Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1516D00E Stem Packing: Graphite, Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated.
1516G005 Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1543W003 A358 Gr 304L Class 1 or 4. Pipe supplied with plain ends will be technically acceptable.
1553E00Z Seamless, To be supplied with 75mm straight after bend at both ends The Supplier shall make provision for thinning during bending to meet the minimum wall thickness after bending. The minimum
thickness at the end tangents shall not be less than the pipe thickness.
1553G00J Speciality Requirement Alternate Material of 304 / 316 / 316L grades shall not be acceptable.
1563B010 Shop Drill & Tap to ASME B1.20.1, 1/2" NPT for Pressure Instrument connections. Tapped centrally. The threads shall be done in a Sasol approved shop facility. Threads shall conform to ASME B1.20.1
specification for thread form, taper, length & dia of thread. Tolerances on taper, lead & angle of thread shall conform to ASME B1.20.1 for NPT threads. All threads shall be N/C Machined. Supplier shall
conform to requirements from SP-50-13 for material certification, PMI, inspection & testing. PMI shall be in accordance with SP-90-23. 100% Thread Inspection shall be conducted by FW Instrument QC
personnel.
* Wall thickness is to be calculated based on individual design conditions. All Flanged Joints, including Valve Bonnets, in FEN service, shall be fitted with
Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Indicating Type for Nitric Acid Service (Milsheff or equivalent). Use
"CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 304L SS CL150 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
1563L002 Flange drilling to ANSI B16.5, Flange to be supplied complete with matching backing ring per referenced standard. Nominal Bore shall be 25.4mm and Nominal Wall Thickness 14.3mm.
1563P008 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1563R009 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1563W00D Flange to be supplied complete with matching backing ring per referenced standard. For details of Ball Joint Facing refer Sasol STDD-5027, Rev 5.
1573S001 Use "CHESTERTON 785 Parting Lubricant" for Anti-Seize with SS flanges.
1576G002 Pegged 316SS with 98% pure graphite laminated on both sides. Construction: Expanded Graphite of 98% Purity, Laminated on both sides of a 0.1mm thick pegged 316 SS Sheet
1576G01L Teflon Gasket/ Nomex- Full length bolt isolating sleeve/ 2 sets high temp phenolic isolating washer + 2 sets steel washer. Type F- Corrosive Hydrocarbon (Max Temp 200°C)
1576G01W Teflon Gasket/ Nomex- Full length bolt isolating sleeves/ 2 sets high temp phenolic isolating washer + 2 sets steel washer. Type E- Corrosive Hydrocarbon (Max Temp 200°C)
1576G01X Teflon Gasket/ Nomex- Full length bolt isolating sleeve/ 2 sets high temp phenolic isolating washer + 2 sets steel washer. Type F- Corrosive Hydrocarbon (Max Temp 200°C)
1592K000 1.6mm diameter wire. 304SS round bar. Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not acceptable unless solution heat treated after repairs.
1592K005 1.6mm diameter wire. 304SS round bar. Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not acceptable unless solution heat treated after repairs.
1598C007 Material- Brass Chicago Coupling. Water/Air service. Male NPT x Quick connector end. Consolidated pneumatic class C15120. Pipe Threads- NPT(Taper). ASME B.1.20.1.
* Wall thickness is to be calculated based on individual design conditions. All Flanged Joints, including Valve Bonnets, in FEN service, shall be fitted with
Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Indicating Type for Nitric Acid Service (Milsheff or equivalent). Use
"CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 304L SS CL150 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1543S00E 0364086 Pipe PE A312-TP304L SMLS 0.5 0.5 Sch 40S - - Sch 40S 310 - - SSSF
- 1543S00F 0364086 Pipe BE A312-TP304L SMLS 0.75 0.75 Sch 40S - - Sch 40S 310 - - SSSF
- 1543S00F 0364086 Pipe BE A312-TP304L SMLS 1 1 Sch 40S - - Sch 40S 310 - - SSSF
- 1543S00F 0364086 Pipe BE A312-TP304L SMLS 1.5 1.5 Sch 40S - - Sch 40S 310 - - SSSF
- 1543S00F 0364082 Pipe BE A312-TP304L SMLS 2 2 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543S00F 0364086 Pipe BE A312-TP304L SMLS 2.5 2.5 Sch 40S* - - Sch 40S* 217 - - SSSF
- 1543S00F 0364082 Pipe BE A312-TP304L SMLS 3 3 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543S00F 0364082 Pipe BE A312-TP304L SMLS 4 4 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543S00F 0364082 Pipe BE A312-TP304L SMLS 6 6 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543S00F 0364082 Pipe BE A312-TP304L SMLS 8 8 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543S00F 0364082 Pipe BE A312-TP304L SMLS 10 10 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543S00F 0364082 Pipe BE A312-TP304L SMLS 12 12 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W006 0364207 Pipe BE A358-304L EFW (Cl 1 or Cl 4) 14 14 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W006 0364207 Pipe BE A358-304L EFW (Cl 1 or Cl 4) 16 16 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W006 0364207 Pipe BE A358-304L EFW (Cl 1 or Cl 4) 18 18 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W006 0364207 Pipe BE A358-304L EFW (Cl 1 or Cl 4) 20 20 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W006 0364207 Pipe BE A358-304L EFW (Cl 1 or Cl 4) 22 22 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W006 0364207 Pipe BE A358-304L EFW (Cl 1 or Cl 4) 24 24 Sch 10S* - - Sch 10S* 217 - - SSSF
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1516C00W 1001306 Check swing RF CL600 A182-F304L BB 304 Trm 0.5 1.5 - - - - - - - SSFF
- 1516G019 1001312 Gate RF CL600 A182-F304L BB 304 Trm 0.5 1.5 - - - - - - - SSFF
714 1516G01D 1001313 Gate SWE X FTE CL800 A182-F304L WB 304 Trm 0.5 1.5 - - - - 102 - - SSSF
- 1516D010 1001308 Globe RF CL600 A182-F304L BB 304 Trm 0.75 1.5 - - - - - - - SSFF
- 1515C00X 1001298 Check swing RF CL150 A351-CF3 BB 304 Trm 2 4 - - - - - - - SSFF
773 1515G01L 1001559 Gate RF CL300 A351-CF3 BB 304 Trm 2 4 - - - - 102 - - SSFF
- 1515D00Z 1001299 Globe RF CL150 A351-CF3 BB 304 Trm 2 10 - - - - - - - SSFF
- 1515G01G 1001559 Gate RF CL150 A351-CF3 BB 304 Trm 2 10 - - - - - - - SSFF
- 1515W008 1001304 Check Wafer RFTBE CL150 A351-CF3 304 Trm 6 24 - - - - - - - SSFF
* Wall thickness is to be calculated based on individual design conditions. All Flanged Joints, including Valve Bonnets, shall be fitted with Indicating Spray
Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Indicating Type for Nitric Acid Service (Milsheff or equivalent). Use "CHESTERTON
785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 3/4 and larger - Butt Weld 2.0 mm 304L SS CL150 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
* Wall thickness is to be calculated based on individual design conditions. All Flanged Joints, including Valve Bonnets, shall be fitted with Indicating Spray
Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Indicating Type for Nitric Acid Service (Milsheff or equivalent). Use "CHESTERTON
785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 3/4 and larger - Butt Weld 2.0 mm 304L SS CL150 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
* Wall thickness is to be calculated based on individual design conditions. All Flanged Joints, including Valve Bonnets, shall be fitted with Indicating Spray
Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Indicating Type for Nitric Acid Service (Milsheff or equivalent). Use "CHESTERTON
785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 3/4 and larger - Butt Weld 2.0 mm 304L SS CL150 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
* Wall thickness is to be calculated based on individual design conditions. All Flanged Joints, including Valve Bonnets, shall be fitted with Indicating Spray
Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Indicating Type for Nitric Acid Service (Milsheff or equivalent). Use "CHESTERTON
785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 3/4 and larger - Butt Weld 2.0 mm 304L SS CL150 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
1515D00Z Teflon Gasket / Packing for Nitric Acid Service. Valve A351-CF8 would be Technically Acceptable. Valves with repair welds are not acceptable unless Solution Heat Treated after repairs.
1515G01G Teflon Gasket / Packing for Nitric Acid Service. Valve A351-CF8 would be Technically Acceptable. Valves with repair welds are not acceptable unless Solution Heat Treated after repairs.
1515G01H Teflon Gasket / Packing for Nitric Acid Service. Valve A351-CF8 would be Technically Acceptable. Valves with repair welds are not acceptable unless Solution Heat Treated after repairs.
1515G01L Teflon Gasket / Packing for Nitric Acid Service Valve A351-CF8 would be Technically Acceptable. Valves with repair welds are not acceptable unless Solution Heat Treated after repairs.
1515W008 Integral seating surfaces; Inconel-X750 temper no. 1 spring; 316 SS Hinge pin / Stop pin / pin retainers / Lug bearings; Dual Plate. Valve A351-CF8 would be Technically Acceptable. 57% Nitric Acid
Service. Valves with repair welds are not acceptable unless Solution Heat Treated after repairs. Supplier shall confirm that mating pipework bore will give adequate disc swing clearance. (Pipe Schedules:
24"-Std)
1516C00W Teflon Gasket / Packing for Nitric Acid Service. Valve A182-F304 would be Technically Acceptable. Valves with repair welds are not acceptable unless Solution Heat Treated after repairs.
1516D010 Teflon Gasket / Packing for Nitric Acid Service. Valve A182-F304 would be Technically Acceptable. Valves with repair welds are not acceptable unless Solution Heat Treated after repairs.
1516G019 Teflon Gasket / Packing for Nitric Acid Service. Valve A182-F304 would be Technically Acceptable. Valves with repair welds are not acceptable unless Solution Heat Treated after repairs.
1516G01D Teflon Packing for Nitric Acid Service. Alternate Material of 304 / 316 / 316L grades shall not be acceptable. Valves with repair welds are not acceptable unless Solution Heat Treated after repairs.
1543S00E Speciality Requirement Alternate Material of 304 / 316 / 316L grades shall not be acceptable.
1543S00F Speciality Requirement Alternate Material of 304 / 316 / 316L grades shall not be acceptable.
1543W006 Speciality Requirement Alternate Material of 304 / 316 / 316L grades shall not be acceptable.
1553E01C Speciality Requirement Alternate Material of 304 / 316 / 316L grades shall not be acceptable.
* Wall thickness is to be calculated based on individual design conditions. All Flanged Joints, including Valve Bonnets, shall be fitted with Indicating Spray
Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Indicating Type for Nitric Acid Service (Milsheff or equivalent). Use "CHESTERTON
785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 3/4 and larger - Butt Weld 2.0 mm 304L SS CL150 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
1553G00E Speciality Requirement Alternate Material of 304 / 316 / 316L grades shall not be acceptable.
1553G00F Speciality Requirement Alternate Material of 304 / 316 / 316L grades shall not be acceptable.
1553G00G Speciality Requirement Alternate Material of 304 / 316 / 316L grades shall not be acceptable.
1553G00H Speciality Requirement Alternate Material of 304 / 316 / 316L grades shall not be acceptable.
1553G00J Speciality Requirement Alternate Material of 304 / 316 / 316L grades shall not be acceptable.
1553G00K Speciality Requirement Alternate Material of 304 / 316 / 316L grades shall not be acceptable.
1553N00L Speciality Requirement Alternate Material of 304 / 316 / 316L grades shall not be acceptable.
1553N00M Speciality Requirement Alternate Material of 304 / 316 / 316L grades shall not be acceptable.
1553U009 Speciality Requirement Alternate Material of 304 / 316 / 316L grades shall not be acceptable.
1553U00A Speciality Requirement Alternate Material of 304 / 316 / 316L grades shall not be acceptable.
1553U00B Speciality Requirement Alternate Material of 304 / 316 / 316L grades shall not be acceptable.
1553U00C Specialty Requirement Alternate Material of 304 / 316 / 316L grades shall not be acceptable.
1553U00D Speciality Requirement Alternate Material of 304 / 316 / 316L grades shall not be acceptable.
1553U00E Speciality Requirement Alternate Material of 304 / 316 / 316L grades shall not be acceptable.
1553W00A Speciality Requirement Alternate Material of 304 / 316 / 316L grades shall not be acceptable.
1563B00W Speciality Requirement Flange A182-F304 would be Technically Acceptable. 57% Nitric Acid Service.
1563B00X Speciality Requirement Flange A182-F304 would be Technically Acceptable. 57% Nitric Acid Service.
* Wall thickness is to be calculated based on individual design conditions. All Flanged Joints, including Valve Bonnets, shall be fitted with Indicating Spray
Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Indicating Type for Nitric Acid Service (Milsheff or equivalent). Use "CHESTERTON
785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 3/4 and larger - Butt Weld 2.0 mm 304L SS CL150 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
1563C00D Speciality Requirement Alternate Material of 304 / 316 / 316L grades shall not be acceptable.
1563L00A Speciality Requirement. Flange drilling to ANSI B16.5, Flange to be supplied complete with matching backing ring per referenced standard. Alternate Material of 304 / 316 / 316L grades shall not be
acceptable.
1563P008 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1563R009 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1563W00D Flange to be supplied complete with matching backing ring per referenced standard. For details of Ball Joint Facing refer Sasol STDD-5027, Rev 5.
1563W011 Speciality Requirement Alternate Material of 304 / 316 / 316L grades shall not be acceptable.
1563W012 Speciality Requirement Alternate Material of 304 / 316 / 316L grades shall not be acceptable.
1573S006 Use "CHESTERTON 785 Parting Lubricant" or equivalent for Anti-Seize with SS flanges. Use in 57% Nitric Acid Service.
1576G01L Teflon Gasket/ Nomex- Full length bolt isolating sleeve/ 2 sets high temp phenolic isolating washer + 2 sets steel washer. Type F- Corrosive Hydrocarbon (Max Temp 200°C)
1576G01P Nitric Acid service- 57% concentration at 93°C Klinger Hygrade LS or equivalent.
1576G01Q Nitric Acid service, 57% concentration at 93°C Klinger Hygrade LS or equivalent.
* Wall thickness is to be calculated based on individual design conditions. All Flanged Joints, including Valve Bonnets, shall be fitted with Indicating Spray
Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Indicating Type for Nitric Acid Service (Milsheff or equivalent). Use "CHESTERTON
785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 3/4 and larger - Butt Weld 2.0 mm 304L SS CL150 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
1592Y010 Speciality Requirement. 304 SS Screen A182-F304 would be Technically Acceptable. 57% Nitric Acid Service. Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs
are not acceptable unless solution heat treated after repairs.
1598C007 Material- Brass Chicago Coupling. Water/Air service. Male NPT x Quick connector end. Consolidated pneumatic class C15120. Pipe Threads- NPT(Taper). ASME B.1.20.1.
* Wall thickness is to be calculated based on individual design conditions. All Flanged Joints, including Valve Bonnets, shall be fitted with Indicating Spray
Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Indicating Type for Nitric Acid Service (Milsheff or equivalent). Use "CHESTERTON
785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 3/4 and larger - Butt Weld 2.0 mm 304L SS CL150 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
Pressure: 1590kPa 1590kPa 1530kPa 1330kPa 1200kPa 1120kPa 1050kPa 1000kPa 930kPa 840kPa 740kPa 650kPa 550kPa 460kPa
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1543S002 0365120 Pipe PE A312-TP316L SMLS 0.5 0.5 Sch 40S - - Sch 40S 310 - - SSSF
- 1543S002 0365120 Pipe PE A312-TP316L SMLS 0.75 0.75 Sch 40S - - Sch 40S 310 - - SSSF
- 1543S002 0365120 Pipe PE A312-TP316L SMLS 1 1 Sch 40S - - Sch 40S 310 - - SSSF
- 1543S003 0365120 Pipe BE A312-TP316L SMLS 1.5 1.5 Sch 40S - - Sch 40S - - - SSSF
- 1543W000 0365187 Pipe BE A312-TP316L EFW 2 2 Sch 10S* - - Sch 10S* 217 - - SSSF F3
- 1543W000 0365187 Pipe BE A312-TP316L EFW 2.5 2.5 Sch 10S* - - Sch 10S* 217 - - SSSF F3
- 1543W000 0365187 Pipe BE A312-TP316L EFW 3 3 Sch 10S* - - Sch 10S* 217 - - SSSF F3
- 1543W000 0365187 Pipe BE A312-TP316L EFW 4 4 Sch 10S* - - Sch 10S* 217 - - SSSF F3
- 1543W000 0365187 Pipe BE A312-TP316L EFW 6 6 Sch 10S* - - Sch 10S* 217 - - SSSF F3
- 1543W000 0365187 Pipe BE A312-TP316L EFW 8 8 Sch 10S* - - Sch 10S* 217 - - SSSF F3
- 1543W000 0365187 Pipe BE A312-TP316L EFW 10 10 Sch 10S* - - Sch 10S* 217 - - SSSF F3
- 1543W000 0365187 Pipe BE A312-TP316L EFW 12 12 Sch 10S* - - Sch 10S* 217 - - SSSF F3
- 1543W004 0365251 Pipe BE A358-316L EFW 14 14 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W004 0365251 Pipe BE A358-316L EFW 16 16 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W004 0365251 Pipe BE A358-316L EFW 18 18 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W004 0365251 Pipe BE A358-316L EFW 20 20 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W004 0365251 Pipe BE A358-316L EFW 22 22 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W004 0365251 Pipe BE A358-316L EFW 24 24 Sch 10S* - - Sch 10S* 217 - - SSSF
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1516B013 1001714 Ball Shrt RF CL300 A182-F316 316SS Fl ball RPTFE WO FB 0.5 1 - - - - 833 721 - SSFF
- 1516C00J 0099047 Check lift SWE CL800 A182-F316L WB 316 Trm 0.5 1 - - - - 159 - - SSSF
- 1516D00F 0100151 Globe SWE CL800 A182-F316L WB 316 Trm 0.5 1 - - - - 159 - - SSSF
- 1516G00S 0099432 Gate SWE CL800 A182-F316L WB 316 Trm 0.5 1 - - - - 159 101 - SSSF
714 1516G00A 0136186 Gate SWE X FTE CL800 A182-F316L WB 316 Trm 0.5 1.5 - - - - 159 102 - SSSF
781 1516G004 0252950 Gate RF CL600 A182-F316 BB 316 Trm 1 1.5 - - - - 159 100 127 SSFF
- 1516C00X 1001307 Check swing BE CL800 A182-F316L 316 Trm 1.5 1.5 Sch 40S - - Sch 40S - - - SSSF
- 1516D011 1001309 Globe BE CL800 A182-F316L WB 316 Trm 1.5 1.5 Sch 40S - - Sch 40S 159 - - SSSF
- 1516G01E 1001314 Gate BE CL800 A182-F316L WB 316 Trm 1.5 1.5 Sch 40S - - Sch 40S 159 101 - SSSF
* Wall thickness is to be calculated based on individual design conditions. Use Spray Shields for Phenol Service. All Flanged Joints, including Valve Bonnets,
shall be fitted with Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid
Service (Milsheff or equivalent). Use "CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 316L SS CL150 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
* Wall thickness is to be calculated based on individual design conditions. Use Spray Shields for Phenol Service. All Flanged Joints, including Valve Bonnets,
shall be fitted with Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid
Service (Milsheff or equivalent). Use "CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 316L SS CL150 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
* Wall thickness is to be calculated based on individual design conditions. Use Spray Shields for Phenol Service. All Flanged Joints, including Valve Bonnets,
shall be fitted with Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid
Service (Milsheff or equivalent). Use "CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 316L SS CL150 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
* Wall thickness is to be calculated based on individual design conditions. Use Spray Shields for Phenol Service. All Flanged Joints, including Valve Bonnets,
shall be fitted with Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid
Service (Milsheff or equivalent). Use "CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 316L SS CL150 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
1515D003 Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1515G00G Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1515G01B Select GO for Differential Pressure of 275 psig across valve Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1515G01C Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1516B013 Floating Ball, Full Bore, Top Entry, Anti-Blowout stem, firesafe design, Valves to comply with API-608 Valve seats and seals shall be rated for the same pressue-temperature rating as of the shell, to ASME
B16.34
* Wall thickness is to be calculated based on individual design conditions. Use Spray Shields for Phenol Service. All Flanged Joints, including Valve Bonnets,
shall be fitted with Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid
Service (Milsheff or equivalent). Use "CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 316L SS CL150 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
1516D011 Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate. Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated.
1516G004 Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1516G00A Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate.
1516G00S Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate.
1516G01E Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate.
1543W004 A358 Gr 316L Class 1 or 4. Pipe supplied with plain ends will be technically acceptable. All austenitic stainless steel pipe shall be furnished in the solution annealed condition.
1553S00C WP-S
1553S00D WP-S
1553S00E WP-S
1553S00F WP-S
1553S00S WP-S
1553S00T WP-S
1553S00U WP-S
1553S00V WP-S
1563B011 Shop Drill & Tap to ASME B1.20.1, 1/2" NPT for Pressure Instrument connections. The threads shall be done in a Sasol approved shop facility. Threads shall conform to ASME B1.20.1 specification for
thread form, taper, length & dia of thread. Tolerances on taper, lead & angle of thread shall conform to ASME B1.20.1 for NPT threads. All threads shall be N/C Machined. Supplier shall conform to
requirements from SP-50-13 for material certification, PMI, inspection & testing. PMI shall be in accordance with SP-90-23. 100% Thread Inspection shall be conducted by FW Instrument QC personnel.
* Wall thickness is to be calculated based on individual design conditions. Use Spray Shields for Phenol Service. All Flanged Joints, including Valve Bonnets,
shall be fitted with Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid
Service (Milsheff or equivalent). Use "CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 316L SS CL150 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
1563L003 Flange drilling to ANSI B16.5, Flange to be supplied complete with matching backing ring per referenced standard. Nominal Bore shall be 25.4mm and Nominal Wall Thickness 14.3mm.
1563P00A Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1563R00A Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1563S00A In accordance with BS 4504 (EN 1092), RF Serrated Finish, 3.2-6.3 micro m
1563S00B Hub dimensions to comply w/ ASME B16.5, Table 6 Flange Designation is as per ASME B16.5, Table 6.
1563W00C Flange to be supplied complete with matching backing ring per referenced standard. For details of Ball Joint Facing refer Sasol STDD-5027, Rev 5.
1563W015 Weld Neck Flange in accordance with BS 4504 (EN 1092), Raised Face Serrated Finish, 3.2-6.3 micro m.
1563W016 Weld Neck Flange in accordance with BS 4504 (EN 1092), Raised Face Serrated Finish, 3.2-6.3 micro m.
1573S003 Use "CHESTERTON 785 Parting Lubricant" for Anti-Seize with SS flanges.
1576G002 Pegged 316SS with 98% pure graphite laminated on both sides. Construction: Expanded Graphite of 98% Purity, Laminated on both sides of a 0.1mm thick pegged 316 SS Sheet
1576G01L Teflon Gasket/ Nomex- Full length bolt isolating sleeve/ 2 sets high temp phenolic isolating washer + 2 sets steel washer. Type F- Corrosive Hydrocarbon (Max Temp 200°C)
1576G01S Teflon Gasket/ Nomex Full length bolt isolating sleeve/ 2 sets high temp phenolic isolating washer + 2 sets steel washer for Phenol Service. Type F- Phenol Service. (Max Temp 200°C)
1576G01X Teflon Gasket/ Nomex- Full length bolt isolating sleeve/ 2 sets high temp phenolic isolating washer + 2 sets steel washer. Type F- Corrosive Hydrocarbon (Max Temp 200°C)
1576G01Z Modified Teflon Gasket (with Glass Microspheres or Silica)/High Temp Full length bolt isolating sleeve/2 sets high temp isolating washer + 2 sets steel washers/Type F- Corrosive Hydrocarbon (Rated for
Max Temp 260ºC)
1576G027 Pegged 316SS with 98% pure graphite laminated on both sides
* Wall thickness is to be calculated based on individual design conditions. Use Spray Shields for Phenol Service. All Flanged Joints, including Valve Bonnets,
shall be fitted with Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid
Service (Milsheff or equivalent). Use "CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 316L SS CL150 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
1592K004 1.6mm diameter wire. 304SS round bar. Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not acceptable unless solution heat treated after repairs.
1592K005 1.6mm diameter wire. 304SS round bar. Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not acceptable unless solution heat treated after repairs.
* Wall thickness is to be calculated based on individual design conditions. Use Spray Shields for Phenol Service. All Flanged Joints, including Valve Bonnets,
shall be fitted with Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid
Service (Milsheff or equivalent). Use "CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 316L SS CL150 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1543S003 0365120 Pipe BE A312-TP316L SMLS 0.5 0.5 Sch 40S - - Sch 40S - - - SSSF
- 1543S003 0365120 Pipe BE A312-TP316L SMLS 0.75 0.75 Sch 40S - - Sch 40S - - - SSSF
- 1543S003 0365120 Pipe BE A312-TP316L SMLS 1 1 Sch 40S - - Sch 40S - - - SSSF
- 1543S003 0365120 Pipe BE A312-TP316L SMLS 1.25 1.25 Sch 40S - - Sch 40S - - - SSSF
- 1543S003 0365120 Pipe BE A312-TP316L SMLS 1.5 1.5 Sch 40S - - Sch 40S - - - SSSF
- 1543S003 0365118 Pipe BE A312-TP316L SMLS 2 2 Sch 10S* - - Sch 10S* - - - SSSF
- 1543S003 0365120 Pipe BE A312-TP316L SMLS 2.5 2.5 Sch 40S* - - Sch 40S* - - - SSSF
- 1543S003 0365118 Pipe BE A312-TP316L SMLS 3 3 Sch 10S* - - Sch 10S* - - - SSSF
- 1543S003 0365118 Pipe BE A312-TP316L SMLS 3.5 3.5 Sch 10S* - - Sch 10S* - - - SSSF
- 1543S003 0365118 Pipe BE A312-TP316L SMLS 4 4 Sch 10S* - - Sch 10S* - - - SSSF
- 1543S003 0365118 Pipe BE A312-TP316L SMLS 5 5 Sch 10S* - - Sch 10S* - - - SSSF
- 1543S003 0365118 Pipe BE A312-TP316L SMLS 6 6 Sch 10S* - - Sch 10S* - - - SSSF
- 1543S003 0365118 Pipe BE A312-TP316L SMLS 8 8 Sch 10S* - - Sch 10S* - - - SSSF
- 1543S003 0365118 Pipe BE A312-TP316L SMLS 10 10 Sch 10S* - - Sch 10S* - - - SSSF
- 1543S003 0365118 Pipe BE A312-TP316L SMLS 12 12 Sch 10S* - - Sch 10S* - - - SSSF
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
714 1516G00A 0136186 Gate SWE X FTE CL800 A182-F316L WB 316 Trm 0.5 0.5 - - - - 102 159 - SSSF
- 1516B010 1001537 Ball Shrt RF CL300 A182-F316L 316SS Fl ball RPTFE WO FB 0.5 1.5 - - - - - - - SSFF
- 1516G004 0252950 Gate RF CL600 A182-F316 BB 316 Trm 0.75 1 - - - - 195 - - SSFF
- 1516C00Y 1001720 Check swing RF CL600 A182-F316L BB 316/Stel Trm 1 1.5 - - - - - - - SSFF
- 1516D00F 0100151 Globe SWE CL800 A182-F316L WB 316 Trm 1 1.5 - - - - - - - SSSF F3
773 1515B00D 1001539 Ball Shrt RF CL300 A351-CF8M 316SS Fl ball RPTFE WO FB 2 3 - - - - 102 - - SSFF
- 1515D003 0254830 Globe RF CL150 A351-CF8M BB 316 Trm 2 3 - - - - 195 - - SSFF
- 1515G004 0251845 Gate RF CL150 A351-CF8M BB 316/Stel Trm 2 3 - - - - 195 - - SSFF
- 1515B008 1001433 Ball Shrt RF CL150 A351-CF8M 316SS Fl ball RPTFE WO FB 2 4 - - - - - - - SSFF
- 1515C005 0257753 Check swing RF CL150 A351-CF8M BB 316 Trm 2 6 - - - - - - - SSFF
773 1515G009 0252235 Gate RF CL300 A351-CF8M BB 316/Stel Trm 3 3 - - - - 102 - - SSFF
- 1515B009 1001434 Ball Shrt RF CL150 A351-CF8M 316SS Fl ball RPTFE GO FB 6 6 - - - - - - - SSFF
*Wall thickness is to be calculated based on individual design conditions. All Flanged Joints, including Valve Bonnets in services with nitric acid pickling, shall
be fitted with Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Indicating Type for Nitric Acid Service (Milsheff or
equivalent). All welds, including weld repairs if any, around the FFE Re-Circulation Piping loop shall be Solution Annealed. Corrosion probes should be
installed around the FFE Re-Circulation Piping Loop to monitor pitting. When used in services with concerns of chloride carryovers, the use of this line class
shall be limited to maximum 60°C.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 0.75 and larger - Butt Weld 1.5 mm 316L SS CL150 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
S I ti G 23 ASME B16 5 P SP 90 2A
- 1515W001 0290396 Check Wafer RFTBE CL150 A351-CF8M 316 Trm DPLT 8 12 - - - - - - - SSFF
- 1515G01M 1001719 Gate RF CL150 A351-CF8M 316/Stel Trm FB 10 10 - - - - 195 - - SSFF
Fittings
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1553H00Y 0498217 Plug MTE A182-F316L Square Head 0.5 1 - - - - 1048 - - SSFF F3
- 1553E004 0449141 90 deg LR elbow BE A403-WP316L WP-S 0.5 1.5 Sch 40S - - Sch 40S - - - SSSF
- 1553E006 0449145 45 deg LR elbow BE A403-WP316L WP-S 0.75 1.5 Sch 40S - - Sch 40S - - - SSSF
- 1553E008 0449153 Tee BE A403-WP316L WP-S 0.75 1.5 Sch 40S - - Sch 40S - - - SSSF
- 1553E00A 0449154 Cap BE A403-WP316L WP-S 0.75 1.5 Sch 40S - - Sch 40S - - - SSSF F3
133 1553E00P 0740292 90 deg bend BE A312-TP316L 5D 1 1.5 Sch 40S - - Sch 40S 721 - - SSSF F3
- 1553R003 0449155 Reducer Con BE A403-WP316L WP-S 1 1.5 Sch 40S 0.5 1 Sch 40S - - - SSSF
- 1553R005 0449156 Reducer Ecc BE A403-WP316L WP-S 1 1.5 Sch 40S 0.5 1 Sch 40S - - - SSSF
- 1553R007 0449153 Reducing tee BE A403-WP316L WP-S 1 1.5 Sch 40S 0.75 1.25 Sch 40S - - - SSSF
- 1553R003 0449155 Reducer Con BE A403-WP316L WP-S 2 2 Sch 40S 1.25 1.25 Sch 40S - - - SSSF
- 1553R005 0449156 Reducer Ecc BE A403-WP316L WP-S 2 2 Sch 40S 1.25 1.25 Sch 40S - - - SSSF
- 1553R003 0449155 Reducer Con BE A403-WP316L WP-S 2 3 Sch 10S* 0.5 1.5 Sch 40S - - - SSSF
- 1553R005 0449156 Reducer Ecc BE A403-WP316L WP-S 2 3 Sch 10S* 0.5 1.5 Sch 40S - - - SSSF
- 1553R007 0449153 Reducing tee BE A403-WP316L WP-S 2 3 Sch 10S* 0.75 1.5 Sch 40S - - - SSSF
133 1553E00P 0740292 90 deg bend BE A312-TP316L 5D 2 4 Sch 40S - - Sch 40S 721 - - SSSF F3
133 1553E00Q 45 deg bend BE A312-TP316L 5D 2 4 Sch 40S - - Sch 40S 721 - - SSSF F3
- 1553G002 0448862 Cap BE A403-WP316L WP-WX 2 12 Sch 10S* - - Sch 10S* - - - SSSF
- 1553G005 0448858 45 deg LR elbow BE A403-WP316L WP-WX 2 12 Sch 10S* - - Sch 10S* - - - SSSF
- 1553G008 0448852 90 deg LR elbow BE A403-WP316L WP-WX 2 12 Sch 10S* - - Sch 10S* - - - SSSF
- 1553G00B 0448861 Tee BE A403-WP316L WP-WX 2 12 Sch 10S* - - Sch 10S* - - - SSSF
133 1553E00P 0740292 90 deg bend BE A312-TP316L 5D 2.5 2.5 Sch 40S* - - Sch 40S* 721 - - SSSF F3
133 1553E00Q 45 deg bend BE A312-TP316L 5D 2.5 2.5 Sch 40S* - - Sch 40S* 721 - - SSSF F3
- 1553G002 0449148 Cap BE A403-WP316L WP-WX 2.5 2.5 Sch 40S* - - Sch 40S* - - - SSSF
- 1553G005 0449144 45 deg LR elbow BE A403-WP316L WP-WX 2.5 2.5 Sch 40S* - - Sch 40S* - - - SSSF
- 1553G008 0449138 90 deg LR elbow BE A403-WP316L WP-WX 2.5 2.5 Sch 40S* - - Sch 40S* - - - SSSF
- 1553G00B 0449147 Tee BE A403-WP316L WP-WX 2.5 2.5 Sch 40S* - - Sch 40S* - - - SSSF
- 1553R003 0449155 Reducer Con BE A403-WP316L WP-S 2.5 2.5 Sch 40S* 1 1.5 Sch 40S - - - SSSF
- 1553R005 0449156 Reducer Ecc BE A403-WP316L WP-S 2.5 2.5 Sch 40S* 1 1.5 Sch 40S - - - SSSF
- 1553R007 0449153 Reducing tee BE A403-WP316L WP-S 2.5 2.5 Sch 40S* 1 1.5 Sch 40S - - - SSSF
- 1553R003 0449155 Reducer Con BE A403-WP316L WP-S 3 3 Sch 10S* 2.5 2.5 Sch 40S* - - - SSSF F3
- 1553W006 0527244 Latrolet BE A182-F316L 3 3 Sch 40S 1 1 Sch 40S 721 - - SSSF
- 1553R005 0449156 Reducer Ecc BE A403-WP316L WP-S 3 4 Sch 10S* 2.5 2.5 Sch 40S* - - - SSSF F3
- 1553U000 0448863 Reducer Con BE A403-WP316L WP-WX 3 5 Sch 10S* 2 2 Sch 10S* - - - SSSF
- 1553U001 0448864 Reducer Ecc BE A403-WP316L WP-WX 3 5 Sch 10S* 2 2 Sch 10S* - - - SSSF
- 1553U002 0449147 Reducing tee BE A403-WP316L WP-WX 3 6 Sch 10S* 2.5 2.5 Sch 40S* - - - SSSF
- 1553U002 0448861 Reducing tee BE A403-WP316L WP-WX 3 12 Sch 10S* 2 10 Sch 10S* - - - SSSF
- 1553A002 1001721 45-deg Lateral RF CL150 A182-F316L 4 4 Sch 40S - - Sch 40S - - - SSFF F3
- 1553R003 0449155 Reducer Con BE A403-WP316L WP-S 4 4 Sch 10S* 3.5 3.5 Sch 10S* - - - SSSF
- 1553U000 0448863 Reducer Con BE A403-WP316L WP-WX 4 12 Sch 10S* 3 10 Sch 10S* 217 311 - SSSF
- 1553U001 0448864 Reducer Ecc BE A403-WP316L WP-WX 4 12 Sch 10S* 3 10 Sch 10S* 217 311 - SSSF
133 1553E01F 1001456 90 deg bend BE A312-TP316L 5D 6 6 Sch 40S - - Sch 40S 721 - - SSSF
133 1553E01G 45 deg bend BE A312-TP316L 5D 6 6 Sch 40S - - Sch 40S 721 - - SSSF
*Wall thickness is to be calculated based on individual design conditions. All Flanged Joints, including Valve Bonnets in services with nitric acid pickling, shall
be fitted with Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Indicating Type for Nitric Acid Service (Milsheff or
equivalent). All welds, including weld repairs if any, around the FFE Re-Circulation Piping loop shall be Solution Annealed. Corrosion probes should be
installed around the FFE Re-Circulation Piping Loop to monitor pitting. When used in services with concerns of chloride carryovers, the use of this line class
shall be limited to maximum 60°C.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 0.75 and larger - Butt Weld 1.5 mm 316L SS CL150 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
S I ti G 23 ASME B16 5 P SP 90 2A
Weldolets
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1553W002 0510631 Weldolet BE A182-F316L 6 12 Sch 10S* 2 6 Sch 10S* 311 - - SSSF
- 1553W002 0510632 Weldolet BE A182-F316L 8 12 Sch 10S* 2.5 2.5 Sch 40S* 311 - - SSSF
Pipe Flanges
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1563W003 0582996 WN flange RF X BE CL300 A182-F316L 0.5 1.5 - - - Sch 40S - - - SSSF
773 1563B005 0616530 Blind flange RF CL300 A182-F316L 0.5 12 - - - - - - - SSFF
- 1563B004 0616520 Blind flange RF CL150 A182-F316L 0.75 12 - - - - - - - SSFF
211 1563B00A 1001722 Blind flange FF CL150 A182-F316L 1 1 - - - - - - - SSFF
173 1563L003 0597179 LWN flange BJ CL600 A182-F316L CW back ring 1 1 - - - Sch 40S 412 - - SSSF
201 1563L006 0616541 LWN back ring BJ CL600 A182-F316L 1 1 - - - - - - - SSFF F3
201 1563W00C 0597179 WN flange BJ X BE CL600 A182-F316L 1 1 - - - Sch 40S 412 - - SSSF
763 1563W004 0582725 WN flange RF X BE CL150 A182-F316L 1 1.5 - - - Sch 40S 832 721 - SSSF
211 1563W007 0582981 WN flange FF X BE CL150 A182-F316L 1 1.5 - - - Sch 40S 832 721 - SSSF F3
211 1563W007 WN flange FF X BE CL150 A182-F316L 2 4 - - - Sch 10S* 832 721 - SSSF F3
773 1563W003 0582991 WN flange RF X BE CL300 A182-F316L 2 12 - - - Sch 10S* 416 - - SSSF
- 1563W004 0582721 WN flange RF X BE CL150 A182-F316L 2 12 - - - Sch 10S* - - - SSSF
773 1563W003 0582996 WN flange RF X BE CL300 A182-F316L 2.5 2.5 - - - Sch 40S* 416 - - SSSF
- 1563W004 0582725 WN flange RF X BE CL150 A182-F316L 2.5 2.5 - - - Sch 40S* - - - SSSF
211 1563W007 0582981 WN flange FF X BE CL150 A182-F316L 2.5 2.5 - - - Sch 40S* 832 721 - SSSF F3
Orifice Flanges
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1563C002 0640592 WN orif flg 0.5" thd tap RF X BE CL300 A182-F316L 2 12 - - - Sch 10S* - - - SSSF
- 1563C002 0640598 WN orif flg 0.5" thd tap RF X BE CL300 A182-F316L 2.5 2.5 - - - Sch 40S* - - - SSSF
Pipe Nipples
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
710 1553N002 0542161 In-line nipple MTE X PE A312-TP316L SMLS 100mm 0.5 1.5 XS - - XS 102 - - SSSF
491 1553N003 0542159 In-line nipple PE A312-TP316L SMLS 100mm 0.75 1.5 XS - - XS - - - SSSF F3
Gaskets
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
160 1576G01X 1001431 GKT CL300 Isolation Set Ring 1.5mm 0.5 1.5 - - - - - - - SSFF F3
- 1574S01V 1001451 GKT CL300 SpW 316L-W Teflon-F CS-CR 316L-IR 4.5mm 0.5 12 - - - - 409 416 - SSFF
- 1574S01U 1001450 GKT CL150 SpW 316L-W Teflon-F CS-CR 316L-IR 4.5mm 0.75 12 - - - - 409 - - SSFF
- 1576G020 GKT CL150 100% Expanded PTFE Full Face cut from sheet 1.5mm 200 1 3.5 - - - - - - - SSFF F3
160 1576G01L 1001431 GKT CL150 Isolation Set Ring 1.5mm 200 2 6 - - - - - - - SSFF
- 1576G020 1001711 GKT CL150 100% Expanded PTFE Full Face cut from sheet 1.5mm 200 4 4 - - - - - - - SSFF F3
Bolting
Option FWSA Client Item T max Min Bolt Max Bolt - Min Bolt Max Bolt - Item Notes Fab.
Code Req. No. Code Item Description (°C) Diam(") Diam(") Length Length A B C Cat. Rev
*Wall thickness is to be calculated based on individual design conditions. All Flanged Joints, including Valve Bonnets in services with nitric acid pickling, shall
be fitted with Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Indicating Type for Nitric Acid Service (Milsheff or
equivalent). All welds, including weld repairs if any, around the FFE Re-Circulation Piping loop shall be Solution Annealed. Corrosion probes should be
installed around the FFE Re-Circulation Piping Loop to monitor pitting. When used in services with concerns of chloride carryovers, the use of this line class
shall be limited to maximum 60°C.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 0.75 and larger - Butt Weld 1.5 mm 316L SS CL150 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
S I ti G 23 ASME B16 5 P SP 90 2A
- 1572S000 0675648 Bolting - A193-B7 lub w/A194-2H Stud 0.5 2 - 50 950 - - - - SSFF
Strainers
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1592Y016 1001766 Y Str RF CL600 A182-F316L 2mm plt 3mm holes 1 1 - - - - - - - SSFF F3
- 1592K006 1001757 T-Type Str basket screen - CL150 316SS 6 Mesh 2 10 Sch 10S* - - Sch 10S* - - - SSFF
- 1592K007 1001760 T-Type Str basket screen - CL150 316SS 7 Mesh 2 10 Sch 10S* - - Sch 10S* - - - SSFF
- 1592K006 1001758 T-Type Str basket screen - CL150 316SS 6 Mesh 2.5 2.5 Sch 40S* - - Sch 40S* - - - SSFF
- 1592K007 1001759 T-Type Str basket screen - CL150 316SS 7 Mesh 2.5 2.5 Sch 40S* - - Sch 40S* - - - SSFF
Miscellaneous
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1563F00A 0749691 Spectacle blank RFTBE CL300 A240-316 0.75 1.5 - - - - - - - SSFF
- 1598C007 1001452 Hose connection MTE X HE B283 Cl.C37700 1 1 - - - - 953 1063 123 SSFF F3
- 1563D00J 0761144 Drip ring 0.75" PE tap RFTBE CL150 A240-316 2 Tap 2 3 - - - - - - - SSFF
- 1563F002 0749673 Spectacle blank RFTBE CL150 A240-316 2 12 - - - - - - - SSFF
773 1563F00A 0749691 Spectacle blank RFTBE CL300 A240-316 3 3 - - - - - - - SSFF F3
- 1563D00K 0761145 Drip ring 1" BE tap RFTBE CL150 A240-316 2 Tap 4 12 - - - - - - - SSFF
*Wall thickness is to be calculated based on individual design conditions. All Flanged Joints, including Valve Bonnets in services with nitric acid pickling, shall
be fitted with Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Indicating Type for Nitric Acid Service (Milsheff or
equivalent). All welds, including weld repairs if any, around the FFE Re-Circulation Piping loop shall be Solution Annealed. Corrosion probes should be
installed around the FFE Re-Circulation Piping Loop to monitor pitting. When used in services with concerns of chloride carryovers, the use of this line class
shall be limited to maximum 60°C.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 0.75 and larger - Butt Weld 1.5 mm 316L SS CL150 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
S I ti G 23 ASME B16 5 P SP 90 2A
Item specific notes
Note Number Description
102 Use only for instrument connections.
123 Use only at utility stations.
159 For bonnet gasket and stem packing, see SP-50-10.
195 Use only when specified on P&I diagram.
217 Minimum thickness permitted. All lines must be calculated for individual design conditions and thicknesses noted on flow diagrams and drawings. See general note 1.15.
311 Select wall thickness and grade to match pipe.
409 Gaskets shall be in accordance with ASME B16.20, spiral wound metallic gaskets.
412 Use only for thermocouple connections.
416 Use where required against flanged control valves and flanged safety valves.
721 Use only where specified on drawings.
832 Use only to tie into existing lines and equipment.
953 Use for water or air service
1048 Use NPS 1/2" and smaller only for intrument connections
1063 Use for condensate and boiler feedwater only
Item option codes
Option Code Description
133 5D bend
160 Isolation kit
173 LWN
201 BJ
211 FFFE
491 PE
710 MTE x PE
714 SWE x FTE
763 CL150
773 CL300
Abbreviations used for item connections
Abbreviation Description
BE Beveled end(/s)
BJ Ball joint
FF Flat-face flanged end(/s)
FTE Female threaded end(/s)
HE Hose end
MTE Male threaded end(/s)
PE Plain end(/s)
RF Raised-face flanged end (3.2 to 6.3 micron RA)
RFTBE Raised-face thru-bolted end(/s)
SWE Socket welded end(/s)
*Wall thickness is to be calculated based on individual design conditions. All Flanged Joints, including Valve Bonnets in services with nitric acid pickling, shall
be fitted with Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Indicating Type for Nitric Acid Service (Milsheff or
equivalent). All welds, including weld repairs if any, around the FFE Re-Circulation Piping loop shall be Solution Annealed. Corrosion probes should be
installed around the FFE Re-Circulation Piping Loop to monitor pitting. When used in services with concerns of chloride carryovers, the use of this line class
shall be limited to maximum 60°C.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 0.75 and larger - Butt Weld 1.5 mm 316L SS CL150 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
S I ti G 23 ASME B16 5 P SP 90 2A
Fabrication Category
Abbreviation Description
SSFF Shop supplied, field fabricated
SSSF Shop supplied, shop fabricated
1515B009 Floating Ball, Full Bore, Top Entry, Valves to comply with API-608 Blow-Out proof stem. Firesafe design + Anti static feature. Valves with repair welds are not acceptable unless Solution Heat Treated after
repairs. Teflon Packing/Gasket. Standard body cavity pressure relief design.
1515B00D Floating Ball, Full Bore, Top Entry, Valves to comply with API-608 Blow-Out proof stem. Firesafe design + Anti static feature. Valves with repair welds are not acceptable unless Solution Heat Treated after
repairs. Teflon Packing/Gasket. Standard body cavity pressure relief design.
1515D003 Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1515G004 Valves with repair welds are not acceptable unless Solution Heat Treated after repairs. Gasket/Packing: Spiral Wound Gasket 316L-W,Teflon-F, CS-CR, 316L-IR. / Teflon.
1515G01M Full Bore Valves with repair welds are not acceptable unless Solution Heat Treated after repairs. Gasket/Packing: Spiral Wound Gasket 316L-W,Teflon-F, CS-CR, 316L-IR. / Teflon. Valves shall not be
fitted with Screwed Seat Rings.
1515W001 Valve with retainerless design. Integral seating surfaces, Inconel-X-750 temper spring, 316SS hinge pin/stop pin/pin retainer/lug bearings. Supplier shall confirm that mating pipework bore will give adequa
disc swing clearance. (Pipe Schedules: 8-12"-Std). Valves with repair welds are not acceptable unless Solution Heat Treated after repairs.
1516B010 Floating Ball, Full Bore, Top Entry, Valves to comply with API-608 Blow-Out proof stem. Firesafe design + Anti static feature. Valves with repair welds are not acceptable unless Solution Heat Treated after
repairs. Teflon Packing/Gasket. Standard body cavity pressure relief design.
1516C00Y Valves with repair welds are not acceptable unless Solution Heat Treated after repairs. Cover Gasket: Spiral Wound Gasket 316L-W,Teflon-F, CS-CR, 316L-IR.
1516D00F Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate.
1516G004 Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1516G00A Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate.
*Wall thickness is to be calculated based on individual design conditions. All Flanged Joints, including Valve Bonnets in services with nitric acid pickling, shall
be fitted with Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Indicating Type for Nitric Acid Service (Milsheff or
equivalent). All welds, including weld repairs if any, around the FFE Re-Circulation Piping loop shall be Solution Annealed. Corrosion probes should be
installed around the FFE Re-Circulation Piping Loop to monitor pitting. When used in services with concerns of chloride carryovers, the use of this line class
shall be limited to maximum 60°C.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 0.75 and larger - Butt Weld 1.5 mm 316L SS CL150 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
S I ti G 23 ASME B16 5 P SP 90 2A
1553A002 Component Design shall be in compliance with ASME B16.5, Flanged Fittings. Manufacturer shall comply with requirements of Para 6.1 and 6.2 of ASME B16.5 for design of such items and shall supply
SIF's for these items.
1553E00P Seamless, To be supplied with 75mm straight after bend at both ends The Supplier shall make provision for thinning during bending to meet the minimum wall thickness after bending. The minimum
thickness at the end tangents shall not be less than the pipe thickness.
1553E00Q Seamless, To be supplied with 75mm straight after bend at both ends The Supplier shall make provision for thinning during bending to meet the minimum wall thickness after bending. The minimum
thickness at the end tangents shall not be less than the pipe thickness.
1553E01F Seamless, to be supplied with 150mm straight after bend at both ends The Supplier shall make provision for thinning during bending to meet the minimum wall thickness after bending. The minimum
thickness at the end tangents shall not be less than the pipe thickness.
1553E01G Seamless, to be supplied with 150mm straight after bend at both ends The Supplier shall make provision for thinning during bending to meet the minimum wall thickness after bending. The minimum
thickness at the end tangents shall not be less than the pipe thickness.
1563L003 Flange drilling to ANSI B16.5, Flange to be supplied complete with matching backing ring per referenced standard. Nominal Bore shall be 25.4mm and Nominal Wall Thickness 14.3mm.
1563W00C Flange to be supplied complete with matching backing ring per referenced standard. For details of Ball Joint Facing refer Sasol STDD-5027, Rev 5.
1576G01L Teflon Gasket/ Nomex- Full length bolt isolating sleeve/ 2 sets high temp phenolic isolating washer + 2 sets steel washer. Type F- Corrosive Hydrocarbon (Max Temp 200°C)
1576G01X Teflon Gasket/ Nomex- Full length bolt isolating sleeve/ 2 sets high temp phenolic isolating washer + 2 sets steel washer. Type F- Corrosive Hydrocarbon (Max Temp 200°C)
1592K006 1.6mm diameter wire. 316SS round bar Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not acceptable unless solution heat treated after repairs.
1592K007 1.6mm diameter wire. 316SS round bar. Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not acceptable unless solution heat treated after repairs.
1598C007 Material- Brass Chicago Coupling. Water/Air service. Male NPT x Quick connector end. Consolidated pneumatic class C15120. Pipe Threads- NPT(Taper). ASME B.1.20.1.
*Wall thickness is to be calculated based on individual design conditions. All Flanged Joints, including Valve Bonnets in services with nitric acid pickling, shall
be fitted with Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Indicating Type for Nitric Acid Service (Milsheff or
equivalent). All welds, including weld repairs if any, around the FFE Re-Circulation Piping loop shall be Solution Annealed. Corrosion probes should be
installed around the FFE Re-Circulation Piping Loop to monitor pitting. When used in services with concerns of chloride carryovers, the use of this line class
shall be limited to maximum 60°C.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 0.75 and larger - Butt Weld 1.5 mm 316L SS CL150 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
S I ti G 23 ASME B16 5 P SP 90 2A
Foster Wheeler SA (Pty) Ltd Service:
Note 73: : Velocity limited to 2.5m/s
Line Class: AZT Phenol (Concentration shall be 70% : 0 Deg C - 80 Deg C
Client: Sasol maximum)
Contract No: 26160
Contract Description: FT Wax Expansion Project
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1541S002 0356033 Pipe PE A106-B SMLS 0.5 0.5 XS - - XS - - - SSSF
- 1541S002 0356033 Pipe PE A106-B SMLS 0.75 0.75 XS - - XS - - - SSSF
- 1541S002 0356033 Pipe PE A106-B SMLS 1 1 XS - - XS - - - SSSF
- 1541S000 0356033 Pipe BE A106-B SMLS 1.5 1.5 XS - - XS - - - SSSF
- 1541S000 0356030 Pipe BE A106-B SMLS 2 2 STD - - STD - - - SSSF
- 1541S000 0356030 Pipe BE A106-B SMLS 3 3 STD - - STD - - - SSSF
- 1541S000 0356030 Pipe BE A106-B SMLS 4 4 STD - - STD - - - SSSF
- 1541S000 0356030 Pipe BE A106-B SMLS 6 6 STD - - STD - - - SSSF
- 1541S000 0356027 Pipe BE A106-B SMLS 8 8 Sch 20 - - Sch 20 - - - SSSF
- 1541S000 0356027 Pipe BE A106-B SMLS 10 10 Sch 20 - - Sch 20 - - - SSSF
- 1541S000 0356027 Pipe BE A106-B SMLS 12 12 Sch 20 - - Sch 20 - - - SSSF
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
714 1512G00A 0115373 Gate SWE X FTE CL800 A105 WB F6/Stell Trm 0.5 0.75 - - - - 102 - - SSSF
- 1512C00L 0063269 Check lift SWE CL800 A105 F6/Stell Trm No Cop 0.5 1 - - - - - - - SSSF
- 1512G00B 0061782 Gate SWE CL800 A105 WB F6/Stell Trm 0.5 1 - - - - - - - SSSF
- 1512D005 0062543 Globe SWE CL800 A105 WB F6/Stell Trm 0.75 1 - - - - - - - SSSF
- 1511C00R 0315309 Check swing BE CL600 A216-WCB BB F6/Stell Trm 1.5 1.5 XS - - XS - - - SSSF
- 1512D00H 0313912 Globe BE CL600 A105 BB F6/Stell Trm 1.5 1.5 XS - - XS - - - SSSF
- 1512G02C 0312600 Gate BE CL800 A105 WB F6/Stell Trm 1.5 1.5 XS - - XS - - - SSSF
781 1512G02D 0158303 Gate RF CL600 A105 WB F6/Stell Trm 1.5 1.5 - - - - 101 127 - SSFF
- 1511C020 0163450 Check swing RF CL150 A216-WCB BB F6 Trm 2 12 - - - - - - - SSFF
- 1512D00D 0160452 Globe RF CL150 A105 BB F6 Trm 2 12 - - - - - - - SSFF
- 1512G003 0156053 Gate RF CL150 A105 BB F6 Trm 2 12 - - - - - - - SSFF
Fittings
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1551H001 0478833 Cap SWE CL3000 A105 0.5 1 - - - - - - - SSSF
- 1551H002 0478830 90 deg elbow SWE CL3000 A105 0.5 1 - - - - - - - SSSF
All Flanged Joints, including Valve Bonnets, shall be fitted with Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Tie-
On Indicating Type for Caustic/Sulphuric Acid Service (Milsheff or equivalent). Threaded connections are not permitted, except that instrument connections
NPS 3/4 and smaller may be threaded downstream of an isolating valve.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and smaller - Socket Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
All Flanged Joints, including Valve Bonnets, shall be fitted with Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Tie-
On Indicating Type for Caustic/Sulphuric Acid Service (Milsheff or equivalent). Threaded connections are not permitted, except that instrument connections
NPS 3/4 and smaller may be threaded downstream of an isolating valve.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and smaller - Socket Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
All Flanged Joints, including Valve Bonnets, shall be fitted with Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Tie-
On Indicating Type for Caustic/Sulphuric Acid Service (Milsheff or equivalent). Threaded connections are not permitted, except that instrument connections
NPS 3/4 and smaller may be threaded downstream of an isolating valve.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and smaller - Socket Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1512D005 Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated. Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G00B Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G02C Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G02D Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1561L001 Flange drilling to ANSI B16.5, Flange to be supplied complete with matching backing ring per referenced standard. Nominal Bore shall be 25.4mm and Nominal Wall Thickness 14.3mm.
1576G01R Teflon Gasket/ Nomex Full length bolt isolating sleeve/ 2 sets high temp phenolic isolating washer + 2 sets steel washer for Phenol Service. Type F- Phenol Service. (Max Temp 200°C)
1592K000 1.6mm diameter wire. 304SS round bar. Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not acceptable unless solution heat treated after repairs.
All Flanged Joints, including Valve Bonnets, shall be fitted with Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Tie-
On Indicating Type for Caustic/Sulphuric Acid Service (Milsheff or equivalent). Threaded connections are not permitted, except that instrument connections
NPS 3/4 and smaller may be threaded downstream of an isolating valve.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and smaller - Socket Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Pressure: 5110kPa 5110kPa 5010kPa 4660kPa 4510kPa 4380kPa 4190kPa 3980kPa 3870kPa 3760kPa 3640kPa 3470kPa
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1541S003 0356234 Pipe PE API-5L-B SMLS 0.5 0.5 XS - - XS 310 - - SSSF
- 1541S003 0356234 Pipe PE API-5L-B SMLS 0.75 0.75 XS - - XS 310 - - SSSF
- 1541S003 0356234 Pipe PE API-5L-B SMLS 1 1 XS - - XS 310 - - SSSF
- 1541S001 0356234 Pipe BE API-5L-B SMLS 1.5 1.5 XS - - XS - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 2 2 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 3 3 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 4 4 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 6 6 STD - - STD - - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 8 8 Sch 20 - - Sch 20 - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 10 10 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 12 12 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 14 14 STD - - STD - - - SSSF
- 1541X009 0356702 Pipe BE API-5L-B DSAW 16 16 Sch 20* - - Sch 20* 217 - - SSSF F3
- 1541X009 0356702 Pipe BE API-5L-B DSAW 18 18 Sch 20* - - Sch 20* 217 - - SSSF F3
- 1541X009 0356704 Pipe BE API-5L-B DSAW 20 20 STD* - - STD* 217 - - SSSF F3
- 1541X009 0356704 Pipe BE API-5L-B DSAW 22 22 STD* - - STD* 217 - - SSSF F3
- 1541X009 0356704 Pipe BE API-5L-B DSAW 24 24 STD* - - STD* 217 - - SSSF F3
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1512C00N 0063273 Check lift SWE CL800 A105 WB F6/Stell Trm 0.5 1 - - - - - - - SSSF
- 1512D005 0062543 Globe SWE CL800 A105 WB F6/Stell Trm 0.5 1 - - - - - - - SSSF
- 1512G00B 0061782 Gate SWE CL800 A105 WB F6/Stell Trm 0.5 1 - - - - 101 - - SSSF
37 1512B019 1001540 Ball Shrt RF CL300 A105 316 Trm Flowserve 94-300 230 0.5 1.5 - - - - 1022 - - SSFF F3
- 1512B01A 1001541 Ball Shrt RF CL300 A105 316SS MS Flowserve 94-300 350 0.5 1.5 - - - - 1022 - - SSFF
714 1512G00A 0115373 Gate SWE X FTE CL800 A105 WB F6/Stell Trm 0.5 1.5 - - - - 102 - - SSSF
24 1512B016 1001445 Ball Shrt RF CL300 A105 316SS MS Trm FB 1 1 - - - - 833 721 - SSFF F3
521 1512B01B Ball SWE CL800 A105 316SS MS Flowserve 94 Series 350 1 1.5 - - - - 1022 - - SSSF
* Wall thickness is to be calculated based on individual design conditions. Caustic Soda and Tar Service not included.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL300 RF Per SP-90-2A
NPS 1½"and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 See SP-90-2A
* Wall thickness is to be calculated based on individual design conditions. Caustic Soda and Tar Service not included.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL300 RF Per SP-90-2A
NPS 1½"and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 See SP-90-2A
* Wall thickness is to be calculated based on individual design conditions. Caustic Soda and Tar Service not included.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL300 RF Per SP-90-2A
NPS 1½"and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 See SP-90-2A
* Wall thickness is to be calculated based on individual design conditions. Caustic Soda and Tar Service not included.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL300 RF Per SP-90-2A
NPS 1½"and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 See SP-90-2A
* Wall thickness is to be calculated based on individual design conditions. Caustic Soda and Tar Service not included.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL300 RF Per SP-90-2A
NPS 1½"and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 See SP-90-2A
* Wall thickness is to be calculated based on individual design conditions. Caustic Soda and Tar Service not included.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL300 RF Per SP-90-2A
NPS 1½"and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 See SP-90-2A
* Wall thickness is to be calculated based on individual design conditions. Caustic Soda and Tar Service not included.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL300 RF Per SP-90-2A
NPS 1½"and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 See SP-90-2A
1511B01E Valve in Full Vacuum service & used for Vacuum Isolation, shall be bubble tight. Seat-Polyfill (1200kPa @ 230°C), Seals by Supplier. Internals to be rated for tightness class A, endurance class CO1, temp
range: 0 to 230°C. Live Loaded Grafoil Packing. Blow-out proof stem. Packing shall be bi-directional in all cases. Compliance with ISO 15848-1 & 2. Supplier shall certify leakage rates. Fire-safe & Anti-
static Design. Flush Port not required. Helium Leak tested. Installed on steam traced pipes carrying process hydrocarbons.
1511B01H Valve in Full Vacuum service & used for Vacuum Isolation, shall be bubble tight. Seat-Metal (1200kPa@350°C), Seals by Supplier. Internals to be rated for tightness class A, endurance class CO1, temp
range:0 to 350°C. Live Loaded Graphoil Packing. Blow-out proof stem. Packing shall be bi-directional in all cases. Compliance with ISO 15848-1&2. Supplier shall certify leakage rates. Flush Port not
required. Helium Leak tested. Installed on steam traced pipes carrying process hydrocarbons.
1511C02C Integral seating surface, Inconel X-spring, 316SS hinge pin/stop pin/pin retainer/lug bearing API-594:-Type A, Dual Plate Double Flanged Check Valve
1511D002 Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler. Globe valve Seat design to conform to API 602
paragraph 5.6.3 unless otherwise stated.
1511D02W Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1511G004 Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1511G005 Flanges >24" to match ASME B16.47, Series B Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler
1512B016 Full Bore, Top Entry, Valves to comply with API-608. Ball-316SS/HC, Seat-316SS/stellite, Body Seal-316SS graphite, Packing-graphite. Firesafe, Blowout Proof Stem. Valve seats and seals shall be rated
for the same pressue-temperature rating as of the shell, to ASME B16.34. Supplier shall provide coating procedure for hard chrome facing to substantiate peeling concerns and Standard body cavity
pressure relief design. Valve in Errosive Service.
* Wall thickness is to be calculated based on individual design conditions. Caustic Soda and Tar Service not included.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL300 RF Per SP-90-2A
NPS 1½"and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 See SP-90-2A
1512B01A Valve in Full Vacuum service & used for Vacuum Isolation, shall be bubble tight. Seat-Metal (1200kPa @ 350°C), Seals by Supplier. Internals to be rated for tightness class A, endurance class CO1, temp
range: 0 to 350°C. Live Loaded Grafoil Packing. Blow-out proof stem. Packing shall be bi-directional in all cases. Compliance with ISO 15848-1 & 2. Supplier shall certify leakage rates. Flush Port not
required. Helium Leak tested. Installed on steam traced pipes carrying process hydrocarbons.
1512B01B Valve in Full Vacuum service & used for Vacuum Isolation, shall be bubble tight. Seat-Metal (1200kPa @ 350°C), Seals by Supplier. Internals to be rated for tightness class A, endurance class CO1, temp
range: 0 to 350°C. Live Loaded Grafoil Packing. Blow-out proof stem. Packing shall be bi-directional in all cases. Compliance with ISO 15848-1 & 2. Supplier shall certify leakage rates. Flush Port not
required. Helium Leak tested. Installed on steam traced pipes carrying process hydrocarbons.
1512B01D Valve in Full Vacuum service & used for Vacuum Isolation, shall be bubble tight. Seat-Polyfill (1200kPa @ 230°C), Seals by Supplier. Internals to be rated for tightness class A, endurance class CO1, temp
range: 0 to 230°C. Live Loaded Grafoil Packing. Blow-out proof stem. Packing shall be bi-directional in all cases. Compliance with ISO 15848-1 & 2. Supplier shall certify leakage rates. Fire-safe & Anti-
static Design. Flush Port not required. Helium Leak tested. Installed on steam traced pipes carrying process hydrocarbons. Valves to be supplied complete with 150mm long plain ended A106-B seamless
(Sch 80) extension pipe pups socket welded to the valve on both ends.
1512D005 Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated. Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512D01J Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated.
1512G00B Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G00D Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G02C Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1541X009 Pipes with wall thickness > 20mm shall be delivered in PWHT condition for all welds. (Supplier to ensure the same for all weld seams, circumferential/longitudnal). PSL 1 Grade. All welded pipes shall be
finished only with longitudnal weld seams, helical/spiral seams shall not be acceptable.
* Wall thickness is to be calculated based on individual design conditions. Caustic Soda and Tar Service not included.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL300 RF Per SP-90-2A
NPS 1½"and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 See SP-90-2A
1561B016 Shop Drill & Tap to ASME B1.20.1, 1/2" NPT for Pressure Instrument connections. Tapped Centrally. The threads shall be done in a Sasol approved shop facility. Threads shall conform to ASME B1.20.1
specification for thread form, taper, length & dia of thread. Tolerances on taper, lead & angle of thread shall conform to ASME B1.20.1 for NPT threads. All threads shall be N/C Machined. Supplier shall
conform to requirements from SP-50-13 for material certification, PMI, inspection & testing. PMI shall be in accordance with SP-90-23. 100% Thread Inspection shall be conducted by FW Instrument QC
personnel.
1561L000 Flange drilling to ANSI B16.5 Nominal Bore shall be 25.4mm and Nominal Wall Thickness 14.3mm.
1561L001 Flange drilling to ANSI B16.5, Flange to be supplied complete with matching backing ring per referenced standard. Nominal Bore shall be 25.4mm and Nominal Wall Thickness 14.3mm.
1561P003 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1561R001 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1561W00F Flange to be supplied complete with matching backing ring per referenced standard. For details of Ball Joint Facing refer Sasol STDD-5027, Rev 5.
1574C001 0.5mm thick 316SS corrugated metal concentric to the bore with a pitch of 3mm. 0.5mm thick 98% pure graphite. Relative density = 1, laminated both sides of core. 0.5mm thick U-shaped 316SS ring on
outside periphery of gasket.
1592K001 1.6mm diameter wire. 304SS round bar. Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not acceptable unless solution heat treated after repairs.
1592K008 1.6mm diameter wire. 304SS round bar. Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not acceptable unless solution heat treated after repairs.
* Wall thickness is to be calculated based on individual design conditions. Caustic Soda and Tar Service not included.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL300 RF Per SP-90-2A
NPS 1½"and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 See SP-90-2A
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1541S000 0356033 Pipe BE A106-B SMLS 0.5 0.5 XS - - XS - - - SSSF F3
- 1541S000 0356033 Pipe BE A106-B SMLS 0.75 0.75 XS - - XS - - - SSSF F3
- 1541S000 0356033 Pipe BE A106-B SMLS 1 1 XS - - XS - - - SSSF F3
- 1541S000 0356033 Pipe BE A106-B SMLS 1.5 1.5 XS - - XS - - - SSSF F3
- 1541S000 0356097 Pipe BE A106-B SMLS 2 2 XS - - XS - - - SSSF F3
- 1541S000 0356030 Pipe BE A106-B SMLS 3 3 STD - - STD - - - SSSF
- 1541S000 0356030 Pipe BE A106-B SMLS 4 4 STD - - STD - - - SSSF
838 1541S000 0356097 Pipe BE A106-B SMLS 4 4 XS - - XS 1000 959 - SSSF F3
- 1541S000 0356030 Pipe BE A106-B SMLS 6 6 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 8 8 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 10 10 STD - - STD - - - SSSF
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1512G00A 0115373 Gate SWE X FTE CL800 A105 WB F6/Stell Trm 0.5 0.5 - - - - 102 - - SSSF F3
- 1512C022 1001291 Check swing RF CL600 A105 BB Stell Trm Slurry Service 1 1.5 - - - - - - - SSFF
- 1512G02L 1001295 Gate RF CL600 A105 WB F6/Stell Trm FB 1 1.5 - - - - - - - SSFF
- 1511C029 1001277 Check swing RF CL300 A216-WCB BB Stell Trm Slurry Service 2 6 - - - - - - - SSFF
- 1511G00S 0156940 Gate RF CL300 A216-WCB BB F6/Stell Trm 2 6 - - - - - - - SSFF
- 1511P00T 1001548 Plug-Fluoroseal RF CL300 A216-WCB (Catalyst Slurry Srv) 285 2 6 - - - - - - - SSFF
- 1511X002 1001289 Rotating disc RF CL300 A216-WCB Stell Trm Slurry Service 2 6 - - - - - - - SSFF
- 1511D006 0160951 Globe RF CL300 A216-WCB BB Stell Trm 4 4 - - - - 195 - - SSFF
Fittings
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1551H00L 0490662 Plug MTE A105 Square Head 0.5 0.5 - - - - - - - SSFF F3
- 1551E00F 1001453 90 deg bend BE API-5L-B 5D 1 1.5 XS - - XS - - - SSSF
- 1551E002 0374286 Cap BE A234-WPB 1 2 XS - - XS - - - SSSF
- 1551E003 0374285 Tee BE A234-WPB 1 2 XS - - XS - - - SSSF
- 1551E00E 1001317 45 deg bend BE API-5L-B 5D 1 2 XS - - XS - - - SSSF
Provide Flanges for removal and cleaning, on pipes at every 10m and both ends of pipe bends. Gate valves to be used only where indicated on MFD's, not for
inline use. HOLD: Rotating Disc / Fluroseal Plug and Slurry Severe Service Ball Valves.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and larger - Butt Weld 3.0 mm Carbon Steel CL300 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Provide Flanges for removal and cleaning, on pipes at every 10m and both ends of pipe bends. Gate valves to be used only where indicated on MFD's, not for
inline use. HOLD: Rotating Disc / Fluroseal Plug and Slurry Severe Service Ball Valves.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and larger - Butt Weld 3.0 mm Carbon Steel CL300 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Provide Flanges for removal and cleaning, on pipes at every 10m and both ends of pipe bends. Gate valves to be used only where indicated on MFD's, not for
inline use. HOLD: Rotating Disc / Fluroseal Plug and Slurry Severe Service Ball Valves.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and larger - Butt Weld 3.0 mm Carbon Steel CL300 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Provide Flanges for removal and cleaning, on pipes at every 10m and both ends of pipe bends. Gate valves to be used only where indicated on MFD's, not for
inline use. HOLD: Rotating Disc / Fluroseal Plug and Slurry Severe Service Ball Valves.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and larger - Butt Weld 3.0 mm Carbon Steel CL300 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1511G00S Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1511P00T Regular Pattern, 2 way, Full Port, Body Gkt - SpW Graphite filled, 304SS-W, 304SS- IR, CS-CR / Plug material - 316SS / Seat material - Manufacturer to recommend / Seat Trim Number 16 per API / Plug
Valve for Catalyst Slurry Service; Fluoroseal, Non-lubricated type, Vertical Installation / ASME B16.34 & Manufacturing / Firesafe Design to API 607 / Dimensions - ASME B16.10 or Manufacturer's Standa
/ Test & Inspection - API 598 / Design Conditions - 0ºC @ 5110 kPa to 285ºC @ 3800 kPa / Manufacturer to advise on Operator type / Valve to be installed vertically directly beneath High Pressure Un-
loading Hopper. Pr. Relief Design
Provide Flanges for removal and cleaning, on pipes at every 10m and both ends of pipe bends. Gate valves to be used only where indicated on MFD's, not for
inline use. HOLD: Rotating Disc / Fluroseal Plug and Slurry Severe Service Ball Valves.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and larger - Butt Weld 3.0 mm Carbon Steel CL300 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1512G02L Graph Packing Full Bore. Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1551E00E To be supplied with 75mm straight after bend at both ends.Bend radius to be 5 x NPS. Seamless. The Supplier shall make provision for thinning during bending to meet the minimum wall thickness after
bending. The minimum thickness at the end tangents shall not be less than the pipe thickness.
1551E00F To be supplied with 75mm straight after bend at both ends. Bend radius to be 5 X pipe OD (NPS) in inches (e.g. 6" therefore to have a radius of 762mm). Seamless. The Supplier shall make provision for
thinning during bending to meet the minimum wall thickness after bending. The minimum thickness at the end tangents shall not be less than the pipe thickness.
1551E01C Seamless, To be supplied with 150mm straight after bend at both ends. Bend radius to be 5 x NPS The Supplier shall make provision for thinning during bending to meet the minimum wall thickness after
bending. The minimum thickness at the end tangents shall not be less than the pipe thickness.
1551E01D Seamless, To be supplied with 150mm straight after bend at both ends. Bend radius to be 5 x NPS The Supplier shall make provision for thinning during bending to meet the minimum wall thickness after
bending. The minimum thickness at the end tangents shall not be less than the pipe thickness.
1551W006 For use on Welding Caps, elliptical heads and flat surfaces.
1576G026 High Integrity, multi layer laminate- Graphite foil with SS foil reinforcement. No adhesive bonding. Gasket with Inner Ring. Gkt / Inner Ring I.D.: 2" - 60mm, 3" - 90mm. Gkt O.D.: 2" - 111mm, 3" - 149mm.
Gasket Inner Ring shall not infringe upon the flow path or exceed the indicated gasket I.D. in any condition, compressed or un-compressed state.
1592K001 1.6mm diameter wire. 304SS round bar. Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not acceptable unless solution heat treated after repairs.
Provide Flanges for removal and cleaning, on pipes at every 10m and both ends of pipe bends. Gate valves to be used only where indicated on MFD's, not for
inline use. HOLD: Rotating Disc / Fluroseal Plug and Slurry Severe Service Ball Valves.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and larger - Butt Weld 3.0 mm Carbon Steel CL300 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Pressure: 5110kPa 5110kPa 5010kPa 4660kPa 4510kPa 4380kPa 4190kPa 3980kPa 3870kPa 3760kPa 3640kPa 3470kPa
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1541S003 0356238 Pipe PE API-5L-B SMLS 0.5 0.5 Sch 160 - - Sch 160 310 - - SSSF
- 1541S003 0356238 Pipe PE API-5L-B SMLS 0.75 0.75 Sch 160 - - Sch 160 310 - - SSSF
- 1541S003 0356238 Pipe PE API-5L-B SMLS 1 1 Sch 160 - - Sch 160 310 - - SSSF
- 1541S001 0356238 Pipe BE API-5L-B SMLS 1.5 1.5 Sch 160 - - Sch 160 310 - - SSSF
- 1541S001 0356234 Pipe BE API-5L-B SMLS 2 2 XS - - XS - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 3 3 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 4 4 STD - - STD - - - SSSF
838 1541S001 0356234 Pipe BE API-5L-B SMLS 6 6 XS - - XS 959 721 - SSSF F3
- 1541S001 0356231 Pipe BE API-5L-B SMLS 6 6 STD - - STD - - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 8 8 Sch 20* - - Sch 20* 217 - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 10 10 Sch 20* - - Sch 20* 217 - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 12 12 Sch 20* - - Sch 20* 217 - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 14 14 Sch 20* - - Sch 20* 217 - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 16 16 Sch 20* - - Sch 20* 217 - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 18 18 Sch 20* - - Sch 20* 217 - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 20 20 STD* - - STD* 217 - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 22 22 STD* - - STD* 217 - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 24 24 STD* - - STD* 217 - - SSSF
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1512B016 1001445 Ball Shrt RF CL300 A105 316SS MS Trm FB 0.5 1 - - - - 833 721 - SSFF
- 1512C00N 0063273 Check lift SWE CL800 A105 WB F6/Stell Trm 0.5 1 - - - - - - - SSSF
- 1512D005 0062543 Globe SWE CL800 A105 WB F6/Stell Trm 0.5 1 - - - - - - - SSSF
- 1512G00B 0061782 Gate SWE CL800 A105 WB F6/Stell Trm 0.5 1 - - - - - - - SSSF
714 1512G00A 0115373 Gate SWE X FTE CL800 A105 WB F6/Stell Trm 0.5 1.5 - - - - 102 - - SSSF
221 1511D00X 0161610 Globe RF CL600 A216-WCB BB F6 Trm 1 1 - - - - - - - SSFF F3
24 1512G02L 1001295 Gate RF CL600 A105 WB F6/Stell Trm FB 1 1 - - - - 833 721 - SSFF
781 1512G02D 0158303 Gate RF CL600 A105 WB F6/Stell Trm 1 1.5 - - - - 100 127 - SSFF
- 1512C01P 0314520 Check swing BE CL800 A105 BB F6/Stell Trm 1.5 1.5 Sch 160 - - Sch 160 - - - SSSF
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1511C02C Integral seating surface, Inconel X-spring, 316SS hinge pin/stop pin/pin retainer/lug bearing API-594:-Type A, Dual Plate Double Flanged Check Valve
1511D002 Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler. Globe valve Seat design to conform to API 602
paragraph 5.6.3 unless otherwise stated.
1511D00F Flanges >24" to match ASME B16.47, Series B Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler
1511D00X Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated.
1511D02W Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1511G004 Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1511G005 Flanges >24" to match ASME B16.47, Series B Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler
1511G03T Full Bore Valve Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1511X002 2-Way, Slurry service (xx to xxx micron metallic particles suspended in wax / xx% weight percent), Shell / seat test in accordance with ASME B16.34, Horizontal installation, Design Temperature = 285°C.
Double Disc
1512B016 Full Bore, Top Entry, Valves to comply with API-608. Ball-316SS/HC, Seat-316SS/stellite, Body Seal-316SS graphite, Packing-graphite. Firesafe, Blowout Proof Stem. Valve seats and seals shall be rated
for the same pressue-temperature rating as of the shell, to ASME B16.34. Supplier shall provide coating procedure for hard chrome facing to substantiate peeling concerns and Standard body cavity
pressure relief design. Valve in Errosive Service.
1512D005 Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated. Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1512G00B Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G02C Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G02D Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G02L Graph Packing Full Bore. Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1551W006 For use on Welding Caps, elliptical heads and flat surfaces.
1561B016 Shop Drill & Tap to ASME B1.20.1, 1/2" NPT for Pressure Instrument connections. Tapped Centrally. The threads shall be done in a Sasol approved shop facility. Threads shall conform to ASME B1.20.1
specification for thread form, taper, length & dia of thread. Tolerances on taper, lead & angle of thread shall conform to ASME B1.20.1 for NPT threads. All threads shall be N/C Machined. Supplier shall
conform to requirements from SP-50-13 for material certification, PMI, inspection & testing. PMI shall be in accordance with SP-90-23. 100% Thread Inspection shall be conducted by FW Instrument QC
personnel.
1561L001 Flange drilling to ANSI B16.5, Flange to be supplied complete with matching backing ring per referenced standard. Nominal Bore shall be 25.4mm and Nominal Wall Thickness 14.3mm.
1561P001 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral. Blank shall be supplied as a set with Spacer, and vice-versa.
1561P002 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral. Spacer shall be supplied as a set with Blank, and vice-versa.
1561P003 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1561R001 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1561W00F Flange to be supplied complete with matching backing ring per referenced standard. For details of Ball Joint Facing refer Sasol STDD-5027, Rev 5.
1592K008 1.6mm diameter wire. 304SS round bar. Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not acceptable unless solution heat treated after repairs.
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1541S003 0356234 Pipe PE API-5L-B SMLS 0.5 0.5 XS - - XS 310 - - SSSF
- 1541S003 0356234 Pipe PE API-5L-B SMLS 0.75 0.75 XS - - XS 310 - - SSSF
- 1541S001 0356234 Pipe BE API-5L-B SMLS 1 1 XS - - XS - - - SSSF
- 1541S001 0356234 Pipe BE API-5L-B SMLS 1.5 1.5 XS - - XS - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 2 2 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 3 3 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 4 4 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 6 6 STD - - STD - - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 8 8 Sch 20 - - Sch 20 - - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 10 10 Sch 20* - - Sch 20* 217 - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 12 12 Sch 20* - - Sch 20* 217 - - SSSF
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1512C01V 0164723 Check lift RF CL600 A105 BB 316 Trm Horiz 1 1.5 - - - - - - - SSFF
- 1512D008 0161733 Globe RF CL600 A105 BB 316 Trm 1 1.5 - - - - 128 - - SSFF
- 1512P009 0295896 Plug Shrt RF CL300 A105 Lubricated 316SS Trm WO 1 1.5 - - - - 100 - - SSFF
- 1511C00F 0164020 Check swing RF CL300 A216-WCB 316 Trm 2 4 - - - - - - - SSFF
- 1511D00C 0161030 Globe RF CL300 A216-WCB BB 316 Trm 2 6 - - - - - - - SSFF
- 1511P00M 0295896 Plug Shrt RF CL300 A216-WCB Lubricated 316SS Trm WO 6 8 - - - - 630 - - SSFF
- 1511W006 0280916 Check Wafer RFTBE CL300 A216-WCB 316 Trm DPLT 6 12 - - - - - - - SSFF
- 1511P00N 0295898 Plug Shrt RF CL300 A216-WCB Lubricated 316SS Trm GO 10 12 - - - - 630 - - SSFF
Fittings
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1551E000 0374276 90 deg LR elbow BE A234-WPB 1 1.5 XS - - XS - - - SSSF
- 1551E001 0374282 45 deg LR elbow BE A234-WPB 1 1.5 XS - - XS - - - SSSF
- 1551E002 0374286 Cap BE A234-WPB 1 1.5 XS - - XS - - - SSSF
- 1551E003 0374285 Tee BE A234-WPB 1 1.5 XS - - XS - - - SSSF
- 1551R000 0374287 Reducer Con BE A234-WPB 1 1.5 XS 0.5 0.75 XS - - - SSSF
Use Spary Shields for Caustic Service. All Flanged Joints, including Valve Bonnets, shall be fitted with Indicating Spray Shields. Spray Shield material shall be
Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid Service (Milsheff or equivalent). Temperature-Pressure range: See
Appendix D, Zone B.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 AND LARGER - BUTT WELD 1.0 mm Carbon Steel CL300 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Use Spary Shields for Caustic Service. All Flanged Joints, including Valve Bonnets, shall be fitted with Indicating Spray Shields. Spray Shield material shall be
Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid Service (Milsheff or equivalent). Temperature-Pressure range: See
Appendix D, Zone B.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 AND LARGER - BUTT WELD 1.0 mm Carbon Steel CL300 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Use Spary Shields for Caustic Service. All Flanged Joints, including Valve Bonnets, shall be fitted with Indicating Spray Shields. Spray Shield material shall be
Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid Service (Milsheff or equivalent). Temperature-Pressure range: See
Appendix D, Zone B.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 AND LARGER - BUTT WELD 1.0 mm Carbon Steel CL300 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1511W006 Dual Plate; Inconel X-750 no 1 temper spring Supplier shall confirm that mating pipework bore will give adequate disc swing clearance. (Pipe Schedules: 6"-Std, 8-S-20, 10-12"-Std)
Use Spary Shields for Caustic Service. All Flanged Joints, including Valve Bonnets, shall be fitted with Indicating Spray Shields. Spray Shield material shall be
Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid Service (Milsheff or equivalent). Temperature-Pressure range: See
Appendix D, Zone B.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 AND LARGER - BUTT WELD 1.0 mm Carbon Steel CL300 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1561L001 Flange drilling to ANSI B16.5, Flange to be supplied complete with matching backing ring per referenced standard. Nominal Bore shall be 25.4mm and Nominal Wall Thickness 14.3mm.
1561P003 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1561R001 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1592K001 1.6mm diameter wire. 304SS round bar. Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not acceptable unless solution heat treated after repairs.
Use Spary Shields for Caustic Service. All Flanged Joints, including Valve Bonnets, shall be fitted with Indicating Spray Shields. Spray Shield material shall be
Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid Service (Milsheff or equivalent). Temperature-Pressure range: See
Appendix D, Zone B.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 AND LARGER - BUTT WELD 1.0 mm Carbon Steel CL300 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1541S004 0358507 Pipe PE A333-6 SMLS 0.5 0.5 XS - - XS 310 - - SSSF
- 1541S004 0358507 Pipe PE A333-6 SMLS 0.75 0.75 XS - - XS 310 - - SSSF
- 1541S004 0358507 Pipe PE A333-6 SMLS 1 1 XS - - XS 310 - - SSSF
- 1541S005 0358507 Pipe BE A333-6 SMLS 1.5 1.5 XS - - XS - - - SSSF
- 1541S005 0358504 Pipe BE A333-6 SMLS 2 2 STD - - STD - - - SSSF
- 1541S005 0358504 Pipe BE A333-6 SMLS 3 3 STD - - STD - - - SSSF
- 1541S005 0358504 Pipe BE A333-6 SMLS 4 4 STD - - STD - - - SSSF
- 1541S005 0358504 Pipe BE A333-6 SMLS 6 6 STD - - STD - - - SSSF
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1512G018 0119163 Gate SWE X FTE CL800 A350-LF2 WB 304 Trm 0.5 0.5 - - - - 102 - - SSSF
- 1511C02J 0351241 Check swing BE CL800 A350-LF2 BB 304 Trm 1 1 - - - - 9 23 160 SSSF
- 1512G02M 0312641 Gate BE CL800 A350-LF2 WB 304 Trm 1 1 XS - - XS 160 23 - SSSF
- 1511D034 0190785 Globe RF CL600 A350-LF2 BB 304 Trm 1 1.5 - - - - 9 23 160 SSFF
221 1512E003 0179665 Gate RF CL600 A350-LF2 BB 304 Trm 1 1.5 - - - - 100 160 23 SSFF
- 1511C01P 0194042 Check swing RF CL300 A352-LCB BB 304 Trm 1.5 4 - - - - 9 23 160 SSFF
- 1511D024 0191152 Globe RF CL300 A352-LCB BB 304 Trm 2 6 - - - - 9 23 160 SSFF
- 1511G02K 0188233 Gate RF CL300 A352-LCB BB 304 Trm 2 6 - - - - 9 23 160 SSFF
Fittings
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1551H008 0478957 90 deg elbow SWE CL3000 A350-LF2 0.5 1 - - - - - - - SSSF
- 1551H009 0478958 45 deg elbow SWE CL3000 A350-LF2 0.5 1 - - - - - - - SSSF
- 1551H00B 0478959 Tee SWE CL3000 A350-LF2 0.5 1 - - - - - - - SSSF
- 1551H016 0478960 Cap SWE CL3000 A350-LF2 0.5 1 - - - - - - - SSSF
- 1551H01L 0491304 Plug MTE A350-LF2 Square Head 0.5 1 - - - - - - - SSFF
- 1551R003 0392611 Reducer Con BE A420-WPL6 1 1 XS 0.75 0.75 XS - - - SSSF
- 1551R004 0392612 Reducer Ecc BE A420-WPL6 1 1 XS 0.75 0.75 XS - - - SSSF
- 1551R005 0392609 Reducing tee BE A420-WPL6 1 1 XS 0.75 0.75 XS - - - SSSF
No Copper or Copper bearing alloy permitted. Materials from this Line Class shall conform to SP-90-18, LT 45. Mandatory PWHT requirement, per SP-90-02A.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Norm. Carbon Steel CL300 RF Per SP-90-2A
NPS 1½"and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.3 ASME B16.5 See SP-90-2A
No Copper or Copper bearing alloy permitted. Materials from this Line Class shall conform to SP-90-18, LT 45. Mandatory PWHT requirement, per SP-90-02A.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Norm. Carbon Steel CL300 RF Per SP-90-2A
NPS 1½"and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.3 ASME B16.5 See SP-90-2A
No Copper or Copper bearing alloy permitted. Materials from this Line Class shall conform to SP-90-18, LT 45. Mandatory PWHT requirement, per SP-90-02A.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Norm. Carbon Steel CL300 RF Per SP-90-2A
NPS 1½"and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.3 ASME B16.5 See SP-90-2A
1511C02J Normalized. No Copper permitted, Valve in -45°C Ammonia Service. Valves with repair welds are not acceptable. SPWND Bonnet Gasket with PTFE filler. Valves for -45°C service shall conform to SP-50-
10C.
No Copper or Copper bearing alloy permitted. Materials from this Line Class shall conform to SP-90-18, LT 45. Mandatory PWHT requirement, per SP-90-02A.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Norm. Carbon Steel CL300 RF Per SP-90-2A
NPS 1½"and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.3 ASME B16.5 See SP-90-2A
1511D034 Normalised and Tempered. Extended Bonnet. No Copper permitted, -45ºC Service. Valves with repair welds are not acceptable without prior approval and unless Post Weld Heat Treated after repairs.
Valves for -45º service shall conform to SP-50-10C. Bonnet gasket SPWND with PTFE filler. Manufacturer shall certify the stem leakage rate. Stem packing shall be pure virgin PTFE, free of organic
material.
1511G02K Normalised and Tempered. Extended Bonnet. No Copper permitted, -45°C Ammonia Service. Valves with repair welds are not acceptable without prior approval and unless Post Weld Heat Treated after
repairs. Valves for -45°C service shall conform to SP-50-10C. SPWND Bonnet Gasket with PTFE filler. Manufacturer shall certify the maximum stem leakage rate. Stem packing shall be pure virgin PTFE,
free of organic material.
1512E003 Extended Body. No Copper or Copper Bearing Alloys. Valve in -45°C service Normalized. Valve in -45°C Ammonia Service. Valves with repair welds are not acceptable. SPWND Bonnet Gasket with PTFE
filler. Valves for -45°C service shall conform to SP-50-10C. Manufacturer shall certify the maximum stem leakage rate. Stem packing shall be pure virgin PTFE, free of organic material.
1512G018 Normalized or Normalized & Tempered. No Copper permitted, Valve in -45°C Ammonia Service. Extended Bonnet. Valves with repair welds are not acceptable. SPWND Bonnet Gasket with PTFE filler.
Valves for -45°C service shall conform to SP-50-10C. Stem Packing- Compressed PTFE rings
1512G02M Extended Body. Valve in -45°C Ammonia Service. No Copper Permitted. Normalized or Normalized & Tempered. Valves with repair welds are not acceptable. Valves for -45°C service shall conform to SP-
50-10C. Stem Packing- Compressed PTFE Rings. Manufacturer shall certify the maximum stem leakage rate.
No Copper or Copper bearing alloy permitted. Materials from this Line Class shall conform to SP-90-18, LT 45. Mandatory PWHT requirement, per SP-90-02A.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Norm. Carbon Steel CL300 RF Per SP-90-2A
NPS 1½"and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.3 ASME B16.5 See SP-90-2A
1561B01B Shorp Dripp & Tap to ASME B1.20.1, 1/2" NPT for Pressure Instrument connections. Normalized. -45°C Ammonia Service. No repair welding shall be acceptable. Tapped Centrally. The threads shall be
done in a Sasol approved shop facility. Threads shall conform to ASME B1.20.1 specification for thread form, taper, length & dia of thread. Tolerances on taper, lead & angle of thread shall conform to
ASME B1.20.1 for NPT threads. All threads shall be N/C Machined. Supplier shall conform to requirements from SP-50-13 for material certification, PMI, inspection & testing. PMI shall be in accordance wi
SP-90-23. 100% Thread Inspection shall be conducted by FW Instrument QC personnel.
1574S00H PTFE filler shall be Pure Virgin PTFE, completely free of organic material.
No Copper or Copper bearing alloy permitted. Materials from this Line Class shall conform to SP-90-18, LT 45. Mandatory PWHT requirement, per SP-90-02A.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Norm. Carbon Steel CL300 RF Per SP-90-2A
NPS 1½"and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.3 ASME B16.5 See SP-90-2A
Pressure: 4140kPa 4140kPa 4000kPa 3480kPa 3140kPa 2920kPa 2750kPa 2610kPa 2550kPa 2510kPa 2480kPa 2430kPa 2390kPa
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1543S007 0364086 Pipe PE A312-TP304L SMLS 0.5 0.5 Sch 40S - - Sch 40S 310 - - SSSF
- 1543S007 0364086 Pipe PE A312-TP304L SMLS 0.75 0.75 Sch 40S - - Sch 40S 310 - - SSSF
- 1543S007 0364086 Pipe PE A312-TP304L SMLS 1 1 Sch 40S - - Sch 40S 310 - - SSSF
- 1543S004 0364086 Pipe BE A312-TP304L SMLS 1.5 1.5 Sch 40S - - Sch 40S - - - SSSF
- 1543S004 0364082 Pipe BE A312-TP304L SMLS 2 2 Sch 10S - - Sch 10S - - - SSSF
- 1543S004 0364082 Pipe BE A312-TP304L SMLS 3 3 Sch 10S - - Sch 10S - - - SSSF
- 1543S004 0364082 Pipe BE A312-TP304L SMLS 4 4 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543S004 0364082 Pipe BE A312-TP304L SMLS 6 6 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543S004 0364082 Pipe BE A312-TP304L SMLS 8 8 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543S004 0364082 Pipe BE A312-TP304L SMLS 10 10 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543S004 0364082 Pipe BE A312-TP304L SMLS 12 12 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W003 0364207 Pipe BE A358-304L EFW (Cl 1 or Cl 4) 14 14 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W003 0364207 Pipe BE A358-304L EFW (Cl 1 or Cl 4) 16 16 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W003 0364207 Pipe BE A358-304L EFW (Cl 1 or Cl 4) 18 18 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W003 0364207 Pipe BE A358-304L EFW (Cl 1 or Cl 4) 20 20 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W003 0364207 Pipe BE A358-304L EFW (Cl 1 or Cl 4) 22 22 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W003 0364207 Pipe BE A358-304L EFW (Cl 1 or Cl 4) 24 24 Sch 10S* - - Sch 10S* 217 - - SSSF
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1516C00H 0095448 Check lift SWE CL800 A182-F304L 304 Trm Horiz 0.5 1 - - - - - - - SSSF
- 1516D00E 0095468 Globe SWE CL800 A182-F304L WB 304 Trm 0.5 1 - - - - - - - SSSF
- 1516G00R 0095409 Gate SWE CL800 A182-F304L WB 304 Trm 0.5 1 - - - - 101 - - SSSF
714 1514G006 0133969 Gate SWE X FTE CL800 A182-F304L WB 304 Trm 0.5 1.5 - - - - 102 - - SSSF
781 1516G005 0243593 Gate RF CL600 A182-F304 BB 304 Trm 0.75 1.5 - - - - 100 127 - SSFF
- 1516C00T 1001305 Check swing BE CL800 A182-F304L BB 304 Trm 1.5 1.5 Sch 40S - - Sch 40S - - - SSSF
- 1516D00X 0341245 Globe BE CL800 A182-F304L WB 304 Trm 1.5 1.5 Sch 40S - - Sch 40S - - - SSSF
- 1516G016 1001310 Gate BE CL800 A182-F304L WB 304 Trm 1.5 1.5 Sch 40S - - Sch 40S 101 - - SSSF
- 1515C00A 0248866 Check swing RF CL300 A351-CF8 BB 316 Trm 2 4 - - - - - - - SSFF
- 1515D007 0245882 Globe RF CL300 A351-CF8 BB 316 Trm 2 6 - - - - - - - SSFF
* Wall thickness is to be calculated based on individual design conditions. Use "CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with
SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 304L SS CL300 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
* Wall thickness is to be calculated based on individual design conditions. Use "CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with
SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 304L SS CL300 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
* Wall thickness is to be calculated based on individual design conditions. Use "CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with
SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 304L SS CL300 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
* Wall thickness is to be calculated based on individual design conditions. Use "CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with
SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 304L SS CL300 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
1515C011 Integral seating surface, Inconel-X750 spring, 316SS hinge pin/stop pin/pin retainer/lug bearing
1515D007 Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1515G00B Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1515G00E Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1516D00E Stem Packing: Graphite, Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated.
1516G005 Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1543W003 A358 Gr 304L Class 1 or 4. Pipe supplied with plain ends will be technically acceptable.
1563B010 Shop Drill & Tap to ASME B1.20.1, 1/2" NPT for Pressure Instrument connections. Tapped centrally. The threads shall be done in a Sasol approved shop facility. Threads shall conform to ASME B1.20.1
specification for thread form, taper, length & dia of thread. Tolerances on taper, lead & angle of thread shall conform to ASME B1.20.1 for NPT threads. All threads shall be N/C Machined. Supplier shall
conform to requirements from SP-50-13 for material certification, PMI, inspection & testing. PMI shall be in accordance with SP-90-23. 100% Thread Inspection shall be conducted by FW Instrument QC
personnel.
* Wall thickness is to be calculated based on individual design conditions. Use "CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with
SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 304L SS CL300 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
1563P002 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1563R002 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1563W00D Flange to be supplied complete with matching backing ring per referenced standard. For details of Ball Joint Facing refer Sasol STDD-5027, Rev 5.
1573S001 Use "CHESTERTON 785 Parting Lubricant" for Anti-Seize with SS flanges.
1576G01X Teflon Gasket/ Nomex- Full length bolt isolating sleeve/ 2 sets high temp phenolic isolating washer + 2 sets steel washer. Type F- Corrosive Hydrocarbon (Max Temp 200°C)
1592K001 1.6mm diameter wire. 304SS round bar. Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not acceptable unless solution heat treated after repairs.
* Wall thickness is to be calculated based on individual design conditions. Use "CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with
SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 304L SS CL300 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
Pressure: 4140kPa 4140kPa 4000kPa 3480kPa 3140kPa 2920kPa 2750kPa 2610kPa 2550kPa 2510kPa 2480kPa 2430kPa 2390kPa 2340kPa
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1543S002 0365120 Pipe PE A312-TP316L SMLS 0.5 0.5 Sch 40S - - Sch 40S 310 - - SSSF
- 1543S002 0365120 Pipe PE A312-TP316L SMLS 0.75 0.75 Sch 40S - - Sch 40S 310 - - SSSF
- 1543S002 0365120 Pipe PE A312-TP316L SMLS 1 1 Sch 40S - - Sch 40S 310 - - SSSF
- 1543S003 0365120 Pipe BE A312-TP316L SMLS 1.5 1.5 Sch 40S - - Sch 40S - - - SSSF
- 1543S003 0365118 Pipe BE A312-TP316L SMLS 2 2 Sch 10S - - Sch 10S - - - SSSF
869 1543S003 0365120 Pipe BE A312-TP316L SMLS 2 2 Sch 40S - - Sch 40S 998 - - SSSF F3
- 1543S003 0365118 Pipe BE A312-TP316L SMLS 2.5 2.5 Sch 10S - - Sch 10S - - - SSSF
- 1543S003 0365118 Pipe BE A312-TP316L SMLS 3 3 Sch 10S - - Sch 10S - - - SSSF
869 1543S003 0365120 Pipe BE A312-TP316L SMLS 3 3 Sch 40S - - Sch 40S 998 - - SSSF F3
- 1543S003 0365118 Pipe BE A312-TP316L SMLS 4 4 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543S003 0365118 Pipe BE A312-TP316L SMLS 6 6 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543S003 0365118 Pipe BE A312-TP316L SMLS 8 8 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543S003 0365118 Pipe BE A312-TP316L SMLS 10 10 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543S003 0365118 Pipe BE A312-TP316L SMLS 12 12 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W004 0365251 Pipe BE A358-316L EFW 14 14 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W004 0365251 Pipe BE A358-316L EFW 16 16 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W004 0365251 Pipe BE A358-316L EFW 18 18 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W004 0365251 Pipe BE A358-316L EFW 20 20 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W004 0365251 Pipe BE A358-316L EFW 22 22 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W004 0365251 Pipe BE A358-316L EFW 24 24 Sch 10S* - - Sch 10S* 217 - - SSSF
- 1543W004 1001316 Pipe BE A358-316L EFW 26 26 Sch 20* - - Sch 20* 217 - - SSSF
- 1543W004 1001316 Pipe BE A358-316L EFW 28 28 Sch 20* - - Sch 20* 217 - - SSSF
- 1543W004 1001316 Pipe BE A358-316L EFW 30 30 Sch 20* - - Sch 20* 217 - - SSSF
- 1543W004 1001316 Pipe BE A358-316L EFW 32 32 Sch 20* - - Sch 20* 217 - - SSSF
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1516C00J 0099047 Check lift SWE CL800 A182-F316L WB 316 Trm 0.5 1 - - - - 159 - - SSSF
- 1516D00F 0100151 Globe SWE CL800 A182-F316L WB 316 Trm 0.5 1 - - - - 159 - - SSSF
- 1516G00S 0099432 Gate SWE CL800 A182-F316L WB 316 Trm 0.5 1 - - - - 159 101 - SSSF
* Wall thickness is to be calculated based on individual design conditions. Use Spray Shields for Phenol Service. All Flanged Joints, including Valve Bonnets,
shall be fitted with Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid
Service (Milsheff or equivalent). Use "CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 316L SS CL300 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
* Wall thickness is to be calculated based on individual design conditions. Use Spray Shields for Phenol Service. All Flanged Joints, including Valve Bonnets,
shall be fitted with Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid
Service (Milsheff or equivalent). Use "CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 316L SS CL300 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
* Wall thickness is to be calculated based on individual design conditions. Use Spray Shields for Phenol Service. All Flanged Joints, including Valve Bonnets,
shall be fitted with Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid
Service (Milsheff or equivalent). Use "CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 316L SS CL300 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
* Wall thickness is to be calculated based on individual design conditions. Use Spray Shields for Phenol Service. All Flanged Joints, including Valve Bonnets,
shall be fitted with Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid
Service (Milsheff or equivalent). Use "CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 316L SS CL300 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
* Wall thickness is to be calculated based on individual design conditions. Use Spray Shields for Phenol Service. All Flanged Joints, including Valve Bonnets,
shall be fitted with Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid
Service (Milsheff or equivalent). Use "CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 316L SS CL300 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
* Wall thickness is to be calculated based on individual design conditions. Use Spray Shields for Phenol Service. All Flanged Joints, including Valve Bonnets,
shall be fitted with Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid
Service (Milsheff or equivalent). Use "CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 316L SS CL300 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
* Wall thickness is to be calculated based on individual design conditions. Use Spray Shields for Phenol Service. All Flanged Joints, including Valve Bonnets,
shall be fitted with Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid
Service (Milsheff or equivalent). Use "CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 316L SS CL300 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
1515B00D Floating Ball, Full Bore, Top Entry, Valves to comply with API-608 Blow-Out proof stem. Firesafe design + Anti static feature. Valves with repair welds are not acceptable unless Solution Heat Treated after
repairs. Teflon Packing/Gasket. Standard body cavity pressure relief design.
1515C012 Integral seating surface, Inconel-X spring, 316SS hinge pin/stop pin/pin retainer/lug bearing API-594:-Type A, Dual Plate Double Flanged Check Valve
1515D002 Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler. Globe valve Seat design to conform to API 602 paragraph 5.6.3
unless otherwise stated.
1515G00G Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1515G01A Enclosed Bevel Gear Operator with Pinion Shat parallel to the flow. Valve mfg to select operator & handwheel size based on valve size and differential pressure of 720 Psig across valve in closed position
Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
* Wall thickness is to be calculated based on individual design conditions. Use Spray Shields for Phenol Service. All Flanged Joints, including Valve Bonnets,
shall be fitted with Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid
Service (Milsheff or equivalent). Use "CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 316L SS CL300 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
1516B011 Anti-Blowout stem, Firesafe design to API 607, Valves to comply with API-608 Used in Phenol Service. Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket-
SPWND with SS-W with Graphite filler.
1516C008 Horizontal Piston Type. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1516D006 Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler. Globe valve Seat design to conform to API 602 paragraph 5.6.3
unless otherwise stated.
1516D00F Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate.
1516D011 Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate. Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated.
1516G004 Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1516G00A Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate.
1516G00S Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate.
1516G01E Stem Packing- Graphite, Manufacturer shall certify maximum stem leakage rate.
1543W004 A358 Gr 316L Class 1 or 4. Pipe supplied with plain ends will be technically acceptable. All austenitic stainless steel pipe shall be furnished in the solution annealed condition.
1553E00P Seamless, To be supplied with 75mm straight after bend at both ends The Supplier shall make provision for thinning during bending to meet the minimum wall thickness after bending. The minimum
thickness at the end tangents shall not be less than the pipe thickness.
1553S00C WP-S
1553S00D WP-S
1553S00E WP-S
1553S00F WP-S
* Wall thickness is to be calculated based on individual design conditions. Use Spray Shields for Phenol Service. All Flanged Joints, including Valve Bonnets,
shall be fitted with Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid
Service (Milsheff or equivalent). Use "CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 316L SS CL300 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
1553S00T WP-S
1553S00U WP-S
1553S00V WP-S
1563B011 Shop Drill & Tap to ASME B1.20.1, 1/2" NPT for Pressure Instrument connections. The threads shall be done in a Sasol approved shop facility. Threads shall conform to ASME B1.20.1 specification for
thread form, taper, length & dia of thread. Tolerances on taper, lead & angle of thread shall conform to ASME B1.20.1 for NPT threads. All threads shall be N/C Machined. Supplier shall conform to
requirements from SP-50-13 for material certification, PMI, inspection & testing. PMI shall be in accordance with SP-90-23. 100% Thread Inspection shall be conducted by FW Instrument QC personnel.
1563L003 Flange drilling to ANSI B16.5, Flange to be supplied complete with matching backing ring per referenced standard. Nominal Bore shall be 25.4mm and Nominal Wall Thickness 14.3mm.
1563P00B Shall be manufactured from a single piece material, I.e. the handle or web shall be integral. NPS >=26", shall be compatible with ASME B16.47 Series B, the Supplier shall include Drawings with dimensio
details and calculations for EC/Sasol approval. The blind shall be designed to the specified Class rating and
to withstand leak (pressure) test conditions as per design code.
1563R00B Shall be manufactured from a single piece material, I.e. the handle or web shall be integral. NPS >=26", shall be compatible with ASME B16.47 Series B, the Supplier shall include Drawings with dimensio
details and calculations for EC/Sasol approval. The blind shall be designed to the specified Class rating and
to withstand leak (pressure) test conditions as per design code.
1563W00C Flange to be supplied complete with matching backing ring per referenced standard. For details of Ball Joint Facing refer Sasol STDD-5027, Rev 5.
1563W016 Weld Neck Flange in accordance with BS 4504 (EN 1092), Raised Face Serrated Finish, 3.2-6.3 micro m.
1573S003 Use "CHESTERTON 785 Parting Lubricant" for Anti-Seize with SS flanges.
1576G01R Teflon Gasket/ Nomex Full length bolt isolating sleeve/ 2 sets high temp phenolic isolating washer + 2 sets steel washer for Phenol Service. Type F- Phenol Service. (Max Temp 200°C)
1576G01X Teflon Gasket/ Nomex- Full length bolt isolating sleeve/ 2 sets high temp phenolic isolating washer + 2 sets steel washer. Type F- Corrosive Hydrocarbon (Max Temp 200°C)
* Wall thickness is to be calculated based on individual design conditions. Use Spray Shields for Phenol Service. All Flanged Joints, including Valve Bonnets,
shall be fitted with Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid
Service (Milsheff or equivalent). Use "CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 316L SS CL300 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
1592K001 1.6mm diameter wire. 304SS round bar. Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not acceptable unless solution heat treated after repairs.
* Wall thickness is to be calculated based on individual design conditions. Use Spray Shields for Phenol Service. All Flanged Joints, including Valve Bonnets,
shall be fitted with Indicating Spray Shields. Spray Shield material shall be Vinyl Coated Woven Glass Fabric- Tie-On Indicating Type for Caustic/Sulphuric Acid
Service (Milsheff or equivalent). Use "CHESTERTON 785 Parting Lubricant" for Anti-Seize when using SS bolts with SS flanges.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 316L SS CL300 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
Pressure: 5110kPa 5110kPa 5010kPa 4660kPa 4510kPa 4380kPa 4190kPa 3980kPa 3870kPa 3760kPa 3640kPa 3470kPa
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1541S000 0356033 Pipe BE A106-B SMLS 0.5 0.5 XS - - XS 310 - - SSSF
- 1541S000 0356033 Pipe BE A106-B SMLS 0.75 0.75 XS - - XS 310 - - SSSF
- 1541S000 0356033 Pipe BE A106-B SMLS 1 1 XS - - XS 310 - - SSSF
- 1541S000 0356033 Pipe BE A106-B SMLS 1.5 1.5 XS - - XS 310 - - SSSF
- 1541S000 0356030 Pipe BE A106-B SMLS 2 2 STD - - STD - - - SSSF
- 1541S000 0356030 Pipe BE A106-B SMLS 3 3 STD - - STD - - - SSSF
- 1541S000 0356030 Pipe BE A106-B SMLS 4 4 STD - - STD - - - SSSF
- 1541S000 0356030 Pipe BE A106-B SMLS 6 6 STD - - STD - - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 8 8 Sch 20 - - Sch 20 - - - SSSF
- 1541S001 0356229 Pipe BE API-5L-B SMLS 10 10 Sch 30 - - Sch 30 - - - SSSF
- 1541S001 0356229 Pipe BE API-5L-B SMLS 12 12 Sch 30 - - Sch 30 - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 14 14 STD - - STD - - - SSSF
- 1541S001 0356230 Pipe BE API-5L-B SMLS 16 16 Sch 40 - - Sch 40 - - - SSSF
- 1541S001 0356234 Pipe BE API-5L-B SMLS 18 18 XS - - XS - - - SSSF
- 1541S001 0356234 Pipe BE API-5L-B SMLS 20 20 XS - - XS - - - SSSF
- 1541S001 0356234 Pipe BE API-5L-B SMLS 24 24 XS* - - XS* - - - SSSF
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
714 1512G00A 0115373 Gate SWE X FTE CL800 A105 WB F6/Stell Trm 0.5 1.5 - - - - 632 - - SSSF
- 1512D01R 1001293 Globe RJ CL600 A105 WB F6/Stell Trm 0.75 1.5 - - - - - - - SSFF
- 1512G02J 1001294 Gate RJ CL600 A105 WB F6/Stell Trm 0.75 1.5 - - - - - - - SSFF
- 1512C023 1001292 Check swing RJ CL600 A105 BB F6/Stell Trm 1 1.5 - - - - - - - SSFF
- 1511C027 1001276 Check swing RJ CL300 A216-WCB BB F6 Trm 2 4 - - - - - - - SSFF
- 1511D02Y 1001280 Globe RJ CL300 A216-WCB BB F6 Trm 2 6 - - - - - - - SSFF
- 1511G03K 1001285 Gate RJ CL300 A216-WCB BB F6 Trm 2 6 - - - - - - - SSFF
- 1511C02K 1001551 Check Dbl Flgd RJ CL300 A216-WCB F6 Trm DPLT 6 24 - - - - - - - SSFF
- 1511D030 1001280 Globe RJ CL300 A216-WCB BB F6 Trm GO 8 10 - - - - - - - SSFF
- 1511G03L 1001287 Gate RJ CL300 A216-WCB BB F6 Trm GO 8 24 - - - - - - - SSFF
1511D02Y Precision Stuffing Box (1.6-3.2um) Live Loaded. Die formed top and bottom bull rings with pure braided graphite packing. SS 316/316L Belleville springs and RF SPWND bonnet gasket. Globe valve Seat
design to conform to API 602 paragraph 5.6.3 unless otherwise stated.
1511D030 Precision Stuffing box (1,6-3,2um) Live loaded. Die formed top and bottom bull rings with pure braided graphite packing. SS 316/316L Belleville springs and RF SPWND bonnet gasket.
1511G03K Precision Stuffing Box (1.6-3.2um) Live Loaded. Die formed top and bottom bull rings with pure braided graphite packing. SS 316/316L Belleville springs and RF SPWND bonnet gasket.
1511G03L Precision Stuffing Box (1.6-3.2um) Live Loaded. Die formed top and bottom bull rings with pure braided graphite packing. SS 316/316L Belleville springs and RF SPWND bonnet gasket.
1512D01R Bellows Sealed with Precision Stuffing Box (1.6-3.2um). 316L Forged Bellow. Die formed top and bottom bull rings with pure braided graphite packing. Vendor shall confirm the Total life cycles for the
bellows. Valve design shall ensure No Torsion of Bellows. Welded bellows shall not be acceptable. Valves in Hot Oil Service. (Max design Temp=400°C)
1512G02J Bellows Sealed with Precision Stuffing Box (1.6-3.2um). 316L Forged Bellow. Die Formed top and bottom bull rings with pure braided graphite packing. Vendor shall confirm the Total life cycles for the
bellows. Valve design shall ensure No Torsion of Bellows. Welded bellows shall not be acceptable. Valves in Hot Oil Service. (Max design Temp=400°C)
1561B017 Shop Drill & Tap to ASME B1.20.1, 1/2" NPT for Pressure Instrument connections. Tapped Centrally. The threads shall be done in a Sasol approved shop facility. Threads shall conform to ASME B1.20.1
specification for thread form, taper, length & dia of thread. Tolerances on taper, lead & angle of thread shall conform to ASME B1.20.1 for NPT threads. All threads shall be N/C Machined. Supplier shall
conform to requirements from SP-50-13 for material certification, PMI, inspection & testing. PMI shall be in accordance with SP-90-23. 100% Thread Inspection shall be conducted by FW Instrument QC
personnel.
1561C00N Refer to FWSA Detail Drawing No.26160-8232-030-54-0001 for arrangement of 3 taps. Orientation of taps suitable for both Gases and/or Liquids in the Vertical Flow Direction only.
1561D01C See Sasol STDD-BR6 for manufacturing details and STDD-BR3 for dimensional details.
1561D01D See Sasol STDD-BR7 for manufacturing details and STDD-BR3 for dimensional details.
1561L001 Flange drilling to ANSI B16.5, Flange to be supplied complete with matching backing ring per referenced standard. Nominal Bore shall be 25.4mm and Nominal Wall Thickness 14.3mm.
1561P00C Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1561R006 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1592K00A 1.6mm diameter wire. 304SS round bar. For fabrication refer FW dwg: 26160-8232-000-54-0007 Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not
acceptable unless solution heat treated after repairs.
1592K00B 1.6mm diameter wire. 304SS round bar. For fabrication refer FW dwg: 26160-8232-000-54-0007 Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not
acceptable unless solution heat treated after repairs.
Pressure: 10210kPa 10210kPa 10020kPa 9320kPa 9020kPa 8760kPa 8390kPa 7960kPa 7740kPa 7510kPa 7270kPa 6940kPa
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1541S002 0356033 Pipe PE A106-B SMLS 0.5 0.5 XS - - XS 310 - - SSSF
- 1541S002 0356033 Pipe PE A106-B SMLS 0.75 0.75 XS - - XS 310 - - SSSF
- 1541S002 0356033 Pipe PE A106-B SMLS 1 1 XS - - XS 310 - - SSSF
- 1541S000 0356033 Pipe BE A106-B SMLS 1.5 1.5 XS - - XS - - - SSSF
- 1541S000 0356030 Pipe BE A106-B SMLS 2 2 STD - - STD - - - SSSF
- 1541S000 0356030 Pipe BE A106-B SMLS 3 3 STD - - STD - - - SSSF
- 1541S000 0356030 Pipe BE A106-B SMLS 4 4 STD - - STD - - - SSSF
- 1541S000 0356030 Pipe BE A106-B SMLS 6 6 STD* - - STD* 217 - - SSSF
- 1541S000 0356027 Pipe BE A106-B SMLS 8 8 Sch 20* - - Sch 20* 217 - - SSSF
- 1541S000 0356027 Pipe BE A106-B SMLS 10 10 Sch 20* - - Sch 20* 217 - - SSSF
- 1541S000 0356027 Pipe BE A106-B SMLS 12 12 Sch 20* - - Sch 20* 217 - - SSSF
- 1541S000 0356027 Pipe BE A106-B SMLS 14 14 Sch 20* - - Sch 20* 217 - - SSSF
- 1541S000 0356027 Pipe BE A106-B SMLS 16 16 Sch 20* - - Sch 20* 217 - - SSSF
- 1541S000 0356030 Pipe BE A106-B SMLS 18 18 STD* - - STD* 217 - - SSSF
- 1541S000 0356030 Pipe BE A106-B SMLS 20 20 STD* - - STD* 217 - - SSSF
- 1541S000 0356033 Pipe BE A106-B SMLS 24 24 XS* - - XS* 217 - - SSSF
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1512C00N 0063273 Check lift SWE CL800 A105 WB F6/Stell Trm 0.5 1 - - - - - - - SSSF
- 1512D005 0062543 Globe SWE CL800 A105 WB F6/Stell Trm 0.5 1 - - - - - - - SSSF
- 1512G00B 0061782 Gate SWE CL800 A105 WB F6/Stell Trm 0.5 1 - - - - - - - SSSF
714 1512G00A 0115373 Gate SWE X FTE CL800 A105 WB F6/Stell Trm 0.5 1.5 - - - - 102 - - SSSF
221 1512D01K 0161610 Globe RF CL600 A105 WB F6/Stell Trm 1 1 - - - - 100 - - SSFF
221 1512G00D 0158303 Gate RF CL600 A105 WB F6/Stell Trm Graph Pack 1 1.5 - - - - 127 - - SSFF
- 1512C01P 0351200 Check swing BE CL800 A105 BB F6/Stell Trm 1.5 1.5 XS - - XS - - - SSSF
- 1512D01J 0341200 Globe BE CL800 A105 WB F6/Stell Trm 1.5 1.5 XS - - XS - - - SSSF
- 1512G02C 0312600 Gate BE CL800 A105 WB F6/Stell Trm 1.5 1.5 XS - - XS - - - SSSF
- 1511C000 0164562 Check swing RF CL600 A216-WCB F6 Trm 2 4 - - - - - - - SSFF
- 1511D00X 0161621 Globe RF CL600 A216-WCB BB F6 Trm 2 4 - - - - - - - SSFF
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1511D00X Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated.
1512D005 Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated. Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512D01J Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated.
1512D01K Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated. Stem Packing: Compressed Graphite Rings
1512G00B Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G00D Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G02C Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1561B018 Shop Drill & Tap to ASME B1.20.1, 1/2" NPT for Pressure Instrument connections. Tapped Centrally. The threads shall be done in a Sasol approved shop facility. Threads shall conform to ASME B1.20.1
specification for thread form, taper, length & dia of thread. Tolerances on taper, lead & angle of thread shall conform to ASME B1.20.1 for NPT threads. All threads shall be N/C Machined. Supplier shall
conform to requirements from SP-50-13 for material certification, PMI, inspection & testing. PMI shall be in accordance with SP-90-23. 100% Thread Inspection shall be conducted by FW Instrument QC
personnel.
1561L001 Flange drilling to ANSI B16.5, Flange to be supplied complete with matching backing ring per referenced standard. Nominal Bore shall be 25.4mm and Nominal Wall Thickness 14.3mm.
1561P001 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral. Blank shall be supplied as a set with Spacer, and vice-versa.
1561P002 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral. Spacer shall be supplied as a set with Blank, and vice-versa.
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Pressure: 10210kPa 10210kPa 10020kPa 9320kPa 9020kPa 8760kPa 8390kPa 7960kPa 7740kPa 7510kPa 7270kPa 6940kPa
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1541S002 0356033 Pipe PE A106-B SMLS 0.5 0.5 XS - - XS 310 - - SSSF
- 1541S002 0356033 Pipe PE A106-B SMLS 0.75 0.75 XS - - XS 310 - - SSSF
- 1541S002 0356033 Pipe PE A106-B SMLS 1 1 XS - - XS 310 - - SSSF
- 1541S000 0356033 Pipe BE A106-B SMLS 1.5 1.5 XS - - XS 310 - - SSSF
- 1541S000 0356030 Pipe BE A106-B SMLS 2 2 STD - - STD - - - SSSF
- 1541S000 0356030 Pipe BE A106-B SMLS 3 3 STD - - STD - - - SSSF
- 1541S000 0356030 Pipe BE A106-B SMLS 4 4 STD - - STD - - - SSSF
- 1541S000 0356030 Pipe BE A106-B SMLS 6 6 STD* - - STD* 217 - - SSSF
- 1541S000 0356027 Pipe BE A106-B SMLS 8 8 Sch 20* - - Sch 20* 217 - - SSSF
- 1541S000 0356027 Pipe BE A106-B SMLS 10 10 Sch 20* - - Sch 20* 217 - - SSSF
- 1541S000 0356027 Pipe BE A106-B SMLS 12 12 Sch 20* - - Sch 20* 217 - - SSSF
- 1541S000 0356027 Pipe BE A106-B SMLS 14 14 Sch 20* - - Sch 20* 217 - - SSSF
- 1541S000 0356027 Pipe BE A106-B SMLS 16 16 Sch 20* - - Sch 20* 217 - - SSSF
- 1541S000 0356030 Pipe BE A106-B SMLS 18 18 STD* - - STD* 217 - - SSSF
- 1541S000 0356030 Pipe BE A106-B SMLS 20 20 STD* - - STD* 217 - - SSSF
- 1541S000 0356033 Pipe BE A106-B SMLS 24 24 XS* - - XS* 217 - - SSSF
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1512G00B 0061782 Gate SWE CL800 A105 WB F6/Stell Trm 0.5 1 - - - - - - - SSSF
714 1512G00A 0115373 Gate SWE X FTE CL800 A105 WB F6/Stell Trm 0.5 1.5 - - - - 102 - - SSSF
- 1512C00N 0063273 Check lift SWE CL800 A105 WB F6/Stell Trm 1 1 - - - - - - - SSSF
- 1512D005 0062543 Globe SWE CL800 A105 WB F6/Stell Trm 1 1 - - - - - - - SSSF
781 1512D01N 1001293 Globe RJ CL600 A105 WB F6/Stell Trm 1 1.5 - - - - 100 721 - SSFF F3
781 1512G02E 0158341 Gate RJ CL600 A105 WB F6/Stell Trm 1 1.5 - - - - 127 - - SSFF
- 1512C01P 0351200 Check swing BE CL800 A105 BB F6/Stell Trm 1.5 1.5 XS - - XS - - - SSSF
- 1512D01J 0341200 Globe BE CL800 A105 WB F6/Stell Trm 1.5 1.5 XS - - XS - - - SSSF
- 1512G02C 0312600 Gate BE CL800 A105 WB F6/Stell Trm 1.5 1.5 XS - - XS - - - SSSF
231 1511G03U 1001748 Gate RJ CL600 A216-WCB BB F6/Stell Trm 2 3 - - - - 102 - - SSFF
- 1511C00R 0315302 Check swing BE CL600 A216-WCB BB F6/Stell Trm 2 4 STD - - STD - - - SSSF
For Pressure - Temperature limits in Hydrogen service, see Appendix E. *Wall thickness is to be calculated based on individual design conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL600 RJ Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
For Pressure - Temperature limits in Hydrogen service, see Appendix E. *Wall thickness is to be calculated based on individual design conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL600 RJ Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
For Pressure - Temperature limits in Hydrogen service, see Appendix E. *Wall thickness is to be calculated based on individual design conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL600 RJ Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
For Pressure - Temperature limits in Hydrogen service, see Appendix E. *Wall thickness is to be calculated based on individual design conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL600 RJ Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
For Pressure - Temperature limits in Hydrogen service, see Appendix E. *Wall thickness is to be calculated based on individual design conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL600 RJ Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1511C02F Integral seating surface, Inconel-X750 temper no. 1 spring; 316SS Hinge pin / Stop pin / pin retainers / Lug bearings API-594:-Type A, Dual Plate Double Flanged Check Valve
1511D00K Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated. Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1511G011 Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1511G012 Valves in Hydrocarbons, hydrocarbons with hydrogen, hydrogen or steam service. (Pr-temp limits for steel in hydrogen service in accordance with Nelson Curves). Stem Packing- Compressed Graphite
Rings, Manufacturer shall certify maximum stem leakage rate.
1511G03U Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512D005 Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated. Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512D01J Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated.
1512D01N Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated.
1512G00B Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G02C Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G02E Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1561B019 Shop Drill & Tap to ASME B1.20.1, 1/2" NPT for Pressure Instrument connections. The threads shall be done in a Sasol approved shop facility. Threads shall conform to ASME B1.20.1 specification for
thread form, taper, length & dia of thread. Tolerances on taper, lead & angle of thread shall conform to ASME B1.20.1 for NPT threads. All threads shall be N/C Machined. Supplier shall conform to
requirements from SP-50-13 for material certification, PMI, inspection & testing. PMI shall be in accordance with SP-90-23. 100% Thread Inspection shall be conducted by FW Instrument QC personnel.
For Pressure - Temperature limits in Hydrogen service, see Appendix E. *Wall thickness is to be calculated based on individual design conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL600 RJ Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1561P00B Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1561R005 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1561W00F Flange to be supplied complete with matching backing ring per referenced standard. For details of Ball Joint Facing refer Sasol STDD-5027, Rev 5.
1592K00C 1.6mm diameter wire. 304SS round bar. For fabrication refer FW dwg: 26160-8232-000-54-0007 Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not
acceptable unless solution heat treated after repairs.
For Pressure - Temperature limits in Hydrogen service, see Appendix E. *Wall thickness is to be calculated based on individual design conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL600 RJ Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Pressure: 15320kPa 15320kPa 15040kPa 13980kPa 13520kPa 13140kPa 12580kPa 11950kPa 11610kPa 11270kPa 10910kPa 10420kPa
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1541S002 0356033 Pipe PE A106-B SMLS 0.5 0.5 XS - - XS 310 - - SSSF
- 1541S002 0356033 Pipe PE A106-B SMLS 0.75 0.75 XS - - XS 310 - - SSSF
- 1541S002 0356033 Pipe PE A106-B SMLS 1 1 XS - - XS 310 - - SSSF
- 1541S000 0356033 Pipe BE A106-B SMLS 1.5 1.5 XS - - XS - - - SSSF
- 1541S000 0356097 Pipe BE A106-B SMLS 2 2 XS - - XS - - - SSSF
- 1541S000 0356097 Pipe BE A106-B SMLS 3 3 XS - - XS - - - SSSF
- 1541S000 0356097 Pipe BE A106-B SMLS 4 4 XS - - XS - - - SSSF
- 1541S000 0356097 Pipe BE A106-B SMLS 6 6 XS* - - XS* 217 - - SSSF
- 1541S000 0356097 Pipe BE A106-B SMLS 8 8 XS* - - XS* 217 - - SSSF
- 1541S000 0356097 Pipe BE A106-B SMLS 10 10 XS* - - XS* 217 - - SSSF
- 1541S000 0356097 Pipe BE A106-B SMLS 12 12 XS* - - XS* 217 - - SSSF
- 1541S000 0356097 Pipe BE A106-B SMLS 14 14 XS* - - XS* 217 - - SSSF
- 1541S000 0356098 Pipe BE A106-B SMLS 16 16 Sch 60* - - Sch 60* 217 - - SSSF
- 1541S000 0356098 Pipe BE A106-B SMLS 18 18 Sch 60* - - Sch 60* 217 - - SSSF
- 1541S000 0356098 Pipe BE A106-B SMLS 20 20 Sch 60* - - Sch 60* 217 - - SSSF
- 1541S000 0356098 Pipe BE A106-B SMLS 22 22 Sch 60* - - Sch 60* 217 - - SSSF
- 1541S000 0356098 Pipe BE A106-B SMLS 24 24 Sch 60* - - Sch 60* 217 - - SSSF
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
521 1512D01L 0062694 Globe SWE CL1500 A105 WB F6/Stell Trm 0.5 1.5 - - - - 102 - - SSSF
- 1512T000 0063494 Check Y-lift SWE CL1500 A105 WB F6/Stell Trm 1 1 - - - - - - - SSSF
- 1512D01M 0162451 Globe Y RJ CL1500 A105 Pr Seal Bon F6/Stell Trm 1 1.5 - - - - 127 100 - SSFF
- 1512T001 0316450 Check Y-lift BE CL1500 A105 WB F6/Stell Trm 1.5 1.5 XS - - XS - - - SSSF
- 1511C02G 0218466 Check Dbl Flgd RJ CL1500 A216-WCB Stell Trm DPLT 2 2 - - - - - - - SSFF
- 1511D02T 0314211 Globe BE CL1500 A216-WCB F6/Stell Trm 2 2 XS - - XS - - - SSSF
- 1511G03C 0312782 Gate BE CL1500 A216-WCB F6/Stell Trm 2 3 XS - - XS - - - SSSF
- 1511D02U 0314002 Globe BE CL900 A216-WCB F6/Stell Trm 3 3 XS - - XS - - - SSSF
- 1511C02H 1000357 Check Dbl Flgd RJ CL900 A216-WCB Stell Trm DPLT 3 24 - - - - - - - SSFF
- 1511D02V 0314004 Globe BE CL900 A216-WCB F6/Stell Trm GO 4 4 XS - - XS - - - SSSF
For Pressure - Temperature limits in Hydrogen service, see Appendix E.*Wall thickness is to be calculated based on individual design conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL900 RJ Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
For Pressure - Temperature limits in Hydrogen service, see Appendix E.*Wall thickness is to be calculated based on individual design conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL900 RJ Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
For Pressure - Temperature limits in Hydrogen service, see Appendix E.*Wall thickness is to be calculated based on individual design conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL900 RJ Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
For Pressure - Temperature limits in Hydrogen service, see Appendix E.*Wall thickness is to be calculated based on individual design conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL900 RJ Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1511C02H Integral seating surface with stellite overlay on body only, Inconel X-750 temper no 1 spring, 316SS hinge pin/stop pin/pin retainer/lug bearing API-594:-Type A, Dual Plate Double Flanged Check Valve
1511D02T with Pressure Seal Bonnet Stem Packing- Compressed Graphite Rings
For Pressure - Temperature limits in Hydrogen service, see Appendix E.*Wall thickness is to be calculated based on individual design conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL900 RJ Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1511D02V with Pressure Seal Bonnet Stem Packing- Compressed Graphite Rings
1561L00B Flange drilling to ANSI B16.5, Flange to be supplied complete with matching backing ring per referenced standard. Nominal Bore shall be 25.4mm and Nominal Wall Thickness 14.3mm.
1561P004 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1561P006 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
For Pressure - Temperature limits in Hydrogen service, see Appendix E.*Wall thickness is to be calculated based on individual design conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL900 RJ Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Pressure: 15510kPa 15510kPa 15510kPa 15440kPa 14920kPa 14390kPa 13900kPa 12860kPa 12400kPa 12070kPa 10980kPa 10140kPa 7720kPa 6865kPa
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1542S000 0359482 Pipe PE A335-P11 SMLS 1 1 Sch 160 - - Sch 160 - - - SSSF
- 1542W000 0359482 Pipe BE A335-P11 SMLS 1.5 1.5 Sch 160 - - Sch 160 - - - SSSF
- 1542W000 0359468 Pipe BE A335-P11 SMLS 2 2 XS* - - XS* 217 - - SSSF
- 1542W000 0359468 Pipe BE A335-P11 SMLS 3 3 XS* - - XS* 217 - - SSSF
- 1542W000 0359468 Pipe BE A335-P11 SMLS 4 4 XS* - - XS* 217 - - SSSF
- 1542W000 0359468 Pipe BE A335-P11 SMLS 6 6 XS* - - XS* 217 - - SSSF
- 1542W000 0359467 Pipe BE A335-P11 SMLS 8 8 Sch 60* - - Sch 60* 217 - - SSSF
- 1542W000 0359468 Pipe BE A335-P11 SMLS 10 10 XS* - - XS* 217 - - SSSF
- 1542W000 0359467 Pipe BE A335-P11 SMLS 12 12 Sch 60* - - Sch 60* 217 - - SSSF
- 1542W000 0359467 Pipe BE A335-P11 SMLS 14 14 Sch 60* - - Sch 60* 217 - - SSSF
- 1542W000 0359467 Pipe BE A335-P11 SMLS 16 16 Sch 60* - - Sch 60* 217 - - SSSF
- 1542W000 0359467 Pipe BE A335-P11 SMLS 18 18 Sch 60* - - Sch 60* 217 - - SSSF
- 1542W000 0359467 Pipe BE A335-P11 SMLS 20 20 Sch 60* - - Sch 60* 217 - - SSSF
- 1542W000 0359467 Pipe BE A335-P11 SMLS 22 22 Sch 60* - - Sch 60* 217 - - SSSF
- 1542W000 0359467 Pipe BE A335-P11 SMLS 24 24 Sch 60* - - Sch 60* 217 - - SSSF
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
521 1514D008 0083387 Globe SWE CL1500 A182-F11 Cl.2 WB F6/Stell Trm 1 1 - - - - 102 112 - SSSF
231 1514D009 0220361 Globe Y RJ CL1500 A182-F11 Cl.2 PSB F6/Stell Trm 1 1.5 - - - - 127 112 100 SSFF
- 1513D009 0341622 Globe BE CL1500 A217-WC6 PSB F6/Stell Trm 2 2 XS* - - XS* 112 402 217 SSSF
- 1513G011 0340176 Gate BE CL1500 A217-WC6 PSB F6/Stell Trm 2 2 XS* - - XS* 112 402 217 SSSF
- 1513D00G 1001297 Globe BE CL900 A217-WC6 PSB F6/Stell Trm 3 3 XS* - - XS* 112 402 217 SSSF
- 1513G012 0340023 Gate BE CL900 A217-WC6 PSB F6/Stell Trm 3 3 XS* - - XS* 112 402 - SSSF
- 1513D00H 0341274 Globe BE CL900 A217-WC6 PSB F6/Stell Trm GO 4 4 XS* - - XS* 112 402 217 SSSF
- 1513G013 0340022 Gate BE CL900 A217-WC6 PSB F6/Stell Trm GO 4 10 XS* - - XS* 112 402 217 SSSF
- 1513G013 0340006 Gate BE CL900 A217-WC6 PSB F6/Stell Trm GO 8 24 Sch 60* - - Sch 60* 112 402 217 SSSF
Fittings
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
For Pressure - Temperature limits in Hydrogen service, see Appendix E. Valves shall not be insulated - see general note 2.1(i). *Wall thickness is to be
calculated based on individual design conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 3.0 mm 1¼Cr - ½Mo CL900 RJ Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.9 ASME B16.5 Per SP-90-2A
For Pressure - Temperature limits in Hydrogen service, see Appendix E. Valves shall not be insulated - see general note 2.1(i). *Wall thickness is to be
calculated based on individual design conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 3.0 mm 1¼Cr - ½Mo CL900 RJ Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.9 ASME B16.5 Per SP-90-2A
For Pressure - Temperature limits in Hydrogen service, see Appendix E. Valves shall not be insulated - see general note 2.1(i). *Wall thickness is to be
calculated based on individual design conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 3.0 mm 1¼Cr - ½Mo CL900 RJ Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.9 ASME B16.5 Per SP-90-2A
For Pressure - Temperature limits in Hydrogen service, see Appendix E. Valves shall not be insulated - see general note 2.1(i). *Wall thickness is to be
calculated based on individual design conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 3.0 mm 1¼Cr - ½Mo CL900 RJ Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.9 ASME B16.5 Per SP-90-2A
1552H00Y Class 1
1552H012 Class 1
1562L000 Flange drilling to ANSI B16.5. Flange to be supplied complete with matching backing ring per referenced standard. NOMINAL BORE SHALL BE 25,4 MM AND NOMINAL WALL THICKNESS 14,3 MM
For Pressure - Temperature limits in Hydrogen service, see Appendix E. Valves shall not be insulated - see general note 2.1(i). *Wall thickness is to be
calculated based on individual design conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 3.0 mm 1¼Cr - ½Mo CL900 RJ Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.9 ASME B16.5 Per SP-90-2A
Pressure: 20680kPa 20680kPa 20010kPa 17390kPa 15700kPa 14580kPa 13730kPa 13030kPa 12740kPa 12540kPa 12380kPa 12150kPa 11930kPa 11710kPa
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1543S002 0365130 Pipe PE A312-TP316L SMLS 0.5 0.5 Sch 160 - - Sch 160 - - - SSSF
- 1543S002 0365130 Pipe PE A312-TP316L SMLS 0.75 0.75 Sch 160 - - Sch 160 - - - SSSF
- 1543S002 0365130 Pipe PE A312-TP316L SMLS 1 1 Sch 160 - - Sch 160 - - - SSSF
- 1543S003 0365130 Pipe BE A312-TP316L SMLS 1.5 1.5 Sch 160 - - Sch 160 310 - - SSSF
- 1543S003 0365136 Pipe BE A312-TP316L SMLS 2 2 Sch 80S* - - Sch 80S* 217 - - SSSF
- 1543S003 0365136 Pipe BE A312-TP316L SMLS 3 3 Sch 80S* - - Sch 80S* 217 - - SSSF
- 1543S003 0365136 Pipe BE A312-TP316L SMLS 4 4 Sch 80S* - - Sch 80S* 217 - - SSSF
- 1543S003 0365136 Pipe BE A312-TP316L SMLS 6 6 Sch 80S* - - Sch 80S* 217 - - SSSF
- 1543S003 0365136 Pipe BE A312-TP316L SMLS 8 8 Sch 80S* - - Sch 80S* 217 - - SSSF
- 1543W004 0365263 Pipe BE A358-316L EFW 10 10 Sch 80* - - Sch 80* 217 - - SSSF
- 1543W004 0365263 Pipe BE A358-316L EFW 12 12 Sch 80* - - Sch 80* 217 - - SSSF
- 1543W004 0365263 Pipe BE A358-316L EFW 14 14 Sch 80* - - Sch 80* 217 - - SSSF
- 1543W004 0365263 Pipe BE A358-316L EFW 16 16 Sch 80* - - Sch 80* 217 - - SSSF
- 1543W004 0365263 Pipe BE A358-316L EFW 18 18 Sch 80* - - Sch 80* 217 - - SSSF
- 1543W004 0365263 Pipe BE A358-316L EFW 20 20 Sch 80* - - Sch 80* 217 - - SSSF
- 1543W004 0365263 Pipe BE A358-316L EFW 22 22 Sch 80* - - Sch 80* 217 - - SSSF
- 1543W004 0365263 Pipe BE A358-316L EFW 24 24 Sch 80* - - Sch 80* 217 - - SSSF
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
521 1516D00V 0099043 Globe SWE CL1500 A182-F316L WB 316L Trm 0.75 1 - - - - 310 112 102 SSSF
- 1516G018 1001311 Gate BE CL1500 A182-F316L WB 316L Trm 1 1 Sch 160 - - Sch 160 101 112 - SSSF
- 1516T000 0099057 Check Y-lift SWE CL1500 A182-F316L WB 316L Trm 1 1 - - - - 112 - - SSSF
231 1516D00W 0256652 Globe Y RJ CL1500 A182-F316 Pr Seal Bon 316 Trm 1 1.5 - - - - 127 112 - SSFF
- 1516D00Z 0350910 Globe BE CL1500 A182-F316L WB 316L Trm 1.5 1.5 Sch 160 - - Sch 160 112 - - SSSF
- 1516T001 1001315 Check Y-lift BE CL1500 A182-F316L WB 316L Trm 1.5 1.5 Sch 160 - - Sch 160 112 - - SSSF
- 1515D00X 0350940 Globe BE CL1500 A351-CF3M Pr Seal Bon 316L Trm 2 3 Sch 80S* - - Sch 80S* 402 112 - SSSF
- 1515G01D 0349431 Gate BE CL1500 A351-CF3M Pr Seal Bon 316L Trm 2 3 Sch 80S* - - Sch 80S* 402 112 - SSSF
- 1515C013 Check Dbl Flgd RJ CL1500 A351-CF8M 316 Trm DPLT 2 24 - - - - 112 - - SSFF
- 1515D00Y 0350980 Globe BE CL1500 A351-CF3M Pr Seal Bon 316L Trm GO 4 6 Sch 80S* - - Sch 80S* 402 112 - SSSF
*Wall thickness is to be calculated based on individual design conditions. Valves shall not be insulated - see general note 2.1(i).
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 316L SS CL1500 RJ Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
*Wall thickness is to be calculated based on individual design conditions. Valves shall not be insulated - see general note 2.1(i).
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 316L SS CL1500 RJ Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
*Wall thickness is to be calculated based on individual design conditions. Valves shall not be insulated - see general note 2.1(i).
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 316L SS CL1500 RJ Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
1543W004 A358 Gr 316L Class 1 or 4. Pipe supplied with plain ends will be technically acceptable. All austenitic stainless steel pipe shall be furnished in the solution annealed condition.
1563L009 Flange drilling to ANSI B16.5, Flange to be supplied complete with matching backing ring per referenced standard. Nominal Bore shall be 25.4mm and Nominal Wall Thickness 14.3mm.
1573S003 Use "CHESTERTON 785 Parting Lubricant" for Anti-Seize with SS flanges.
*Wall thickness is to be calculated based on individual design conditions. Valves shall not be insulated - see general note 2.1(i).
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm 316L SS CL1500 RJ Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
Pressure: Atm kPa Atm kPa Atm kPa Atm kPa Atm kPa
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1541X001 0356649 Pipe BE API-5L-B ERW 2 2 STD - - STD - - - SSSF
- 1541X001 0356649 Pipe BE API-5L-B ERW 3 3 STD - - STD - - - SSSF
- 1541X001 0356649 Pipe BE API-5L-B ERW 4 4 STD - - STD - - - SSSF
- 1541X001 0356649 Pipe BE API-5L-B ERW 6 6 STD - - STD - - - SSSF
- 1541X004 0356806 Pipe BE SABS 719 ERW Straight Seam 8 8 Sch 20 - - Sch 20 - - - SSSF
- 1541X004 0356806 Pipe BE SABS 719 ERW Straight Seam 10 10 Sch 20 - - Sch 20 - - - SSSF
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1511G002 0156061 Gate RF CL150 A216-WCB BB F6 Trm 4 6 - - - - - - - SSFF F3
Fittings
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1551E000 0374114 90 deg LR elbow BE A234-WPB 2 6 STD - - STD - - - SSSF
- 1551E001 0374120 45 deg LR elbow BE A234-WPB 2 6 STD - - STD - - - SSSF
- 1551R000 0374125 Reducer Con BE A234-WPB 3 6 STD 2 4 STD - - - SSSF
- 1551E000 0373952 90 deg LR elbow BE A234-WPB 8 10 Sch 20 - - Sch 20 - - - SSSF
- 1551E001 0373958 45 deg LR elbow BE A234-WPB 8 10 Sch 20 - - Sch 20 - - - SSSF
- 1551R000 0374125 Reducer Con BE A234-WPB 8 10 Sch 20 4 6 STD - - - SSSF
- 1551R000 0373963 Reducer Con BE A234-WPB 10 10 Sch 20 8 8 Sch 20 - - - SSSF
Pipe Flanges
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1561B000 0615476 Blind flange RF CL150 A105 4 10 - - - - - - - SSFF
- 1561S000 0597469 SO flange RF X PE CL150 A105 4 10 - - - - - - - SSSF
Gaskets
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
All underground pipe and fittings shall be externally coated and wrapped in accordance with SP-50-6.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 2 and larger - Butt Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
All underground pipe and fittings shall be externally coated and wrapped in accordance with SP-50-6.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 2 and larger - Butt Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
All underground pipe and fittings shall be externally coated and wrapped in accordance with SP-50-6.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 2 and larger - Butt Weld 1.0 mm Carbon Steel CL150 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1543W001 0364151 Pipe BE A312-TP304L EFW 4 4 Sch 10S - - Sch 10S - - - SSSF
- 1543W001 0364151 Pipe BE A312-TP304L EFW 6 6 Sch 10S - - Sch 10S - - - SSSF
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1513B000 Ball Shrt RF CL150 A351-CF8 304SS ball R-PTFE Firesafe FB 4 4 - - - - - - - SSFF
Fittings
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1553G00A 0438645 Tee BE A403-WP304L WP-WX 4 4 Sch 10S - - Sch 10S - - - SSSF
- 1553G004 0438642 45 deg LR elbow BE A403-WP304L WP-WX 4 6 Sch 10S - - Sch 10S - - - SSSF
- 1553G007 0438636 90 deg LR elbow BE A403-WP304L WP-WX 4 6 Sch 10S - - Sch 10S - - - SSSF
- 1553U003 0438647 Reducer Con BE A403-WP304L WP-WX 6 6 Sch 10S 4 4 Sch 10S - - - SSSF
- 1553U005 0438645 Reducing tee BE A403-WP304L WP-WX 6 6 Sch 10S 4 4 Sch 10S 212 - - SSSF
Pipe Flanges
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
221 1563B00M Blind flange RF CL150 A182-F304 4 4 - - - - - - - SSFF
221 1563W005 0576903 WN flange RF X BE CL150 A182-F304L 4 4 - - - Sch 10S - - - SSSF
- 1563B00T 0616267 Blind flange FF CL150 A182-F304 4 6 - - - - - - - SSFF
- 1563S007 0598346 SO flange FF X PE CL150 A182-F304L 4 6 - - - - - - - SSSF
Gaskets
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1574S00T 0672123 GKT CL150 SpW 304-W graph-F CS-CR 304-IR 4.5mm 4 4 - - - - - - - SSFF
- 1576G00T 0665102 GKT CL150 Graph full face 2mm 4 6 - - - - - - - SSFF
All Underground Pipe and Fittings shall be Externally Coated & Wrapped in accordance with SP-50-6.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 4" and larger - Butt Weld 1.0 mm 304L SS CL150 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
All Underground Pipe and Fittings shall be Externally Coated & Wrapped in accordance with SP-50-6.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 4" and larger - Butt Weld 1.0 mm 304L SS CL150 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
1576G00T Expanded graphite, reinforced with synthetic fibre, silicate filler and a nitrile rubber binder.
All Underground Pipe and Fittings shall be Externally Coated & Wrapped in accordance with SP-50-6.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 4" and larger - Butt Weld 1.0 mm 304L SS CL150 RF Per SP-90-2A
Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 2.3 ASME B16.5 Per SP-90-2A
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1541S003 0356234 Pipe PE API-5L-B SMLS 0.5 0.5 XS - - XS 310 - - SSSF
- 1541S003 0356234 Pipe PE API-5L-B SMLS 0.75 0.75 XS - - XS 310 - - SSSF
- 1541S003 0356234 Pipe PE API-5L-B SMLS 1 1 XS - - XS 310 - - SSSF
- 1541S003 0356234 Pipe PE API-5L-B SMLS 1.5 1.5 XS - - XS 310 - - SSSF
- 1541X001 0356649 Pipe BE API-5L-B ERW 2 2 STD - - STD - - - SSSF
- 1541X001 0356649 Pipe BE API-5L-B ERW 3 3 STD - - STD - - - SSSF
- 1541X001 0356649 Pipe BE API-5L-B ERW 4 4 STD - - STD - - - SSSF
- 1541X001 0356649 Pipe BE API-5L-B ERW 6 6 STD - - STD - - - SSSF
- 1541X004 0356806 Pipe BE SABS 719 ERW Straight Seam 8 8 Sch 20* - - Sch 20* 217 - - SSSF F3
- 1541X004 0356806 Pipe BE SABS 719 ERW Straight Seam 10 10 Sch 20* - - Sch 20* 217 - - SSSF F3
- 1541X004 0356806 Pipe BE SABS 719 ERW Straight Seam 12 12 Sch 20* - - Sch 20* 217 - - SSSF F3
- 1541X004 0356806 Pipe BE SABS 719 ERW Straight Seam 14 14 Sch 20* - - Sch 20* 217 - - SSSF F3
- 1541X004 0356806 Pipe BE SABS 719 ERW Straight Seam 16 16 Sch 20* - - Sch 20* 217 - - SSSF F3
- 1541X004 0356806 Pipe BE SABS 719 ERW Straight Seam 18 18 Sch 20* - - Sch 20* 217 - - SSSF F3
- 1541X004 0356807 Pipe BE SABS 719 ERW Straight Seam 20 20 STD* - - STD* 217 - - SSSF F3
- 1541X004 0356807 Pipe BE SABS 719 ERW Straight Seam 22 22 STD* - - STD* 217 - - SSSF F3
- 1541X004 0356807 Pipe BE SABS 719 ERW Straight Seam 24 24 STD* - - STD* 217 - - SSSF F3
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1512C00N 0063273 Check lift SWE CL800 A105 WB F6/Stell Trm 0.5 1.5 - - - - 9 - - SSSF
- 1512D005 0062543 Globe SWE CL800 A105 WB F6/Stell Trm 0.5 1.5 - - - - 9 - - SSSF
714 1512G00A 0115373 Gate SWE X FTE CL800 A105 WB F6/Stell Trm 0.5 1.5 - - - - 9 102 - SSSF
- 1512G00B 0061782 Gate SWE CL800 A105 WB F6/Stell Trm 0.5 1.5 - - - - 9 - - SSSF
541 1518C003 0002670 Check swing FTE CL300 A47-32510 BSP No Cop 0.5 1.5 - - - - 9 123 - SSFF
781 1512G00D 0158303 Gate RF CL600 A105 WB F6/Stell Trm Graph Pack 1 1.5 - - - - 9 101 127 SSFF
211 1518G001 0153434 Gate FF CL125 A126-B All Iron Trm 2 2 - - - - 9 153 - SSFF
- 1518C004 0153792 Check swing FF CL125 A126-B All Iron Trm No Cop 2 6 - - - - 9 153 - SSFF
- 1511G00C 0156070 Gate RF CL150 A216-WCB BB F6 Trm No Cop 2 10 - - - - 9 107 - SSFF
1) Use only for tie-ins or minor modifications to existing lines. 2) Confirm wall thickness of existing lines that are being tied into. *Wall thickness is to be
calculated based on individual design conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1½ and smaller - Socket Weld 1.0 mm Carbon Steel CL150 RF None
NPS 2 and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Cast Iron ASME B16.1 CLASS B Per SP-90-2A
1) Use only for tie-ins or minor modifications to existing lines. 2) Confirm wall thickness of existing lines that are being tied into. *Wall thickness is to be
calculated based on individual design conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1½ and smaller - Socket Weld 1.0 mm Carbon Steel CL150 RF None
NPS 2 and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Cast Iron ASME B16.1 CLASS B Per SP-90-2A
NPS 2 and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Cast Iron ASME B16.1 CLASS B Per SP-90-2A
1) Use only for tie-ins or minor modifications to existing lines. 2) Confirm wall thickness of existing lines that are being tied into. *Wall thickness is to be
calculated based on individual design conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1½ and smaller - Socket Weld 1.0 mm Carbon Steel CL150 RF None
NPS 2 and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Cast Iron ASME B16.1 CLASS B Per SP-90-2A
1) Use only for tie-ins or minor modifications to existing lines. 2) Confirm wall thickness of existing lines that are being tied into. *Wall thickness is to be
calculated based on individual design conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1½ and smaller - Socket Weld 1.0 mm Carbon Steel CL150 RF None
NPS 2 and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Cast Iron ASME B16.1 CLASS B Per SP-90-2A
1511G01G No copper allowed Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1512D005 Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated. Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G00B Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G00D Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1518C004 No copper or copper bearing alloys permitted. Reference - Crane # 373-1/2 or approved equivalent.
1518D002 No Copper
1518F004 TYPE I SEAT - BUNA-N SHAFT - 304 STAINLESS STEEL STANDARDS, 2 FLANGE, NO COPPER Short body flanged Butterfly Valve conforming to AWWA C504. Flange drillings to conform to ASME
B16.5 CL150. Supplier shall confirm that mating pipework bore will give adequate disc swing clearance.
1518F005 TYPE I SEAT - BUNA-N SHAFT - 304 STAINLESS STEEL STANDARDS, 2 FLANGE, NO COPPER Short body flanged Butterfly valve conforming to AWWA C504. Flange drillings to conform to ASME
B16.5 CL150. Supplier shall confirm that mating pipework bore will give adequate disc swing clearance.
1518G001 Generally in accordance with API-600. No copper or copper bearing alloys permitted.
1) Use only for tie-ins or minor modifications to existing lines. 2) Confirm wall thickness of existing lines that are being tied into. *Wall thickness is to be
calculated based on individual design conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1½ and smaller - Socket Weld 1.0 mm Carbon Steel CL150 RF None
NPS 2 and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Cast Iron ASME B16.1 CLASS B Per SP-90-2A
1561L001 Flange drilling to ANSI B16.5, Flange to be supplied complete with matching backing ring per referenced standard. Nominal Bore shall be 25.4mm and Nominal Wall Thickness 14.3mm.
1561P000 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1561R000 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1576G00T Expanded graphite, reinforced with synthetic fibre, silicate filler and a nitrile rubber binder.
1) Use only for tie-ins or minor modifications to existing lines. 2) Confirm wall thickness of existing lines that are being tied into. *Wall thickness is to be
calculated based on individual design conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1½ and smaller - Socket Weld 1.0 mm Carbon Steel CL150 RF None
NPS 2 and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Cast Iron ASME B16.1 CLASS B Per SP-90-2A
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1541H000 0358400 Pipe MTE SABS 62 Galvanised ERW 0.5 0.5 Med - - Med 202 - - SSFF
- 1541H000 0358400 Pipe MTE SABS 62 Galvanised ERW 0.75 0.75 Med - - Med 202 - - SSFF
- 1541H000 0358400 Pipe MTE SABS 62 Galvanised ERW 1 1 Med - - Med 202 - - SSFF
- 1541H000 0358400 Pipe MTE SABS 62 Galvanised ERW 1.5 1.5 Med - - Med 202 - - SSFF
- 1541H000 0358400 Pipe MTE SABS 62 Galvanised ERW 2 2 Med - - Med 202 - - SSFF
- 1541H000 0358400 Pipe MTE SABS 62 Galvanised ERW 2.5 2.5 Med - - Med 202 - - SSFF
- 1541H000 0358400 Pipe MTE SABS 62 Galvanised ERW 3 3 Med - - Med 202 - - SSFF
- 1541H000 0358400 Pipe MTE SABS 62 Galvanised ERW 4 4 Med - - Med 202 - - SSFF
- 1541H000 0358400 Pipe MTE SABS 62 Galvanised ERW 6 6 Med - - Med 202 - - SSFF
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1517G000 0000514 Gate FTE CL150 B62 Bronze Trm BSP 0.5 2 - - - - - - - SSFF
- 1517C000 0000776 Check swing FTE CL150 B61 Bronze Trm BSP 0.5 3 - - - - - - - SSFF
- 1517D000 0000633 Globe FTE CL150 B62 Bronze Trm BSP 0.5 3 - - - - - - - SSFF
- 1518G001 Gate FF CL125 A126-B All Iron Trm 3 3 - - - - - - - SSFF F3
- 1518F004 0307102 Bfly LP FF CL150 A126-B Cast Aust Iron Disc Buna N Flgd 3 6 - - - - 153 630 - SSFF
- 1518C004 0153792 Check swing FF CL125 A126-B All Iron Trm No Cop 4 6 - - - - 153 - - SSFF
- 1518D002 0153612 Globe FF CL125 A126-B All Iron Trm No Cop 4 6 - - - - 153 - - SSFF
Fittings
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1557H000 0488671 90 deg elbow FTE Malleable CI Galv SANS 14 0.5 4 - - - - 51 - - SSFF
- 1557H001 0488673 45 deg elbow FTE Malleable CI Galv SANS 14 0.5 4 - - - - 51 - - SSFF
- 1557H003 0488676 Cap FTE Malleable CI Galvanised SANS 14 0.5 4 - - - - 51 - - SSFF
- 1557H002 0488675 Tee FTE Malleable CI Galv SANS 14 0.5 6 - - - - 51 - - SSFF
- 1557H004 0488677 Coupling FTE Malleable CI Galv SANS 14 0.5 6 - - - - 51 - - SSFF
- 1557H005 0488696 Plug MTE Malleable CI Galv Square Head SANS 14 0.5 6 - - - - 51 - - SSFF
541 1557H006 0488703 Union FTE Malleable CI Galv SANS 14 0.5 6 - - - - 51 - - SSFF
- 1557F000 0488675 Reducing tee FTE Malleable CI Galv SANS 14 0.75 6 - 0.5 4 - 51 - - SSFF
NPS 8" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Cast Iron ASME B16.1 1000 kPa Screwed Conns: NDE Per SP-90-2A
NPS 8" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Cast Iron ASME B16.1 1000 kPa Screwed Conns: NDE Per SP-90-2A
1517G000 ISRS-SB, Ends shall be internally taper threaded to BS 21. Reference: Crane #431 or approved equivalent.
NPS 8" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Cast Iron ASME B16.1 1000 kPa Screwed Conns: NDE Per SP-90-2A
1518D002 No Copper
1518F004 TYPE I SEAT - BUNA-N SHAFT - 304 STAINLESS STEEL STANDARDS, 2 FLANGE, NO COPPER Short body flanged Butterfly Valve conforming to AWWA C504. Flange drillings to conform to ASME
B16.5 CL150. Supplier shall confirm that mating pipework bore will give adequate disc swing clearance.
1518G001 Generally in accordance with API-600. No copper or copper bearing alloys permitted.
1541H000 Pipe to be supplied threaded to SANS 1109 both ends cw one galvanised SANS 14 / ISO 49 full coupling
1576G00S Expanded graphite, reinforced with synthetic fibre, silicate filler and a nitrile rubber binder.
1576G00T Expanded graphite, reinforced with synthetic fibre, silicate filler and a nitrile rubber binder.
1576G01C Expanded graphite, reinforced with synthetic fibre, silicate filler and a nitrile rubber binder.
1576G01X Teflon Gasket/ Nomex- Full length bolt isolating sleeve/ 2 sets high temp phenolic isolating washer + 2 sets steel washer. Type F- Corrosive Hydrocarbon (Max Temp 200°C)
1598C007 Material- Brass Chicago Coupling. Water/Air service. Male NPT x Quick connector end. Consolidated pneumatic class C15120. Pipe Threads- NPT(Taper). ASME B.1.20.1.
NPS 8" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Cast Iron ASME B16.1 1000 kPa Screwed Conns: NDE Per SP-90-2A
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1541S003 0356234 Pipe PE API-5L-B SMLS 0.5 0.5 XS - - XS 26 - - SSSF
- 1541S003 0356234 Pipe PE API-5L-B SMLS 0.75 0.75 XS - - XS 26 - - SSSF
- 1541S003 0356234 Pipe PE API-5L-B SMLS 1 1 XS - - XS 26 - - SSSF
- 1541S003 0356234 Pipe PE API-5L-B SMLS 1.5 1.5 XS - - XS 26 - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 2 2 STD - - STD 202 - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 2.5 2.5 STD - - STD 202 - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 3 3 STD - - STD 202 - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 4 4 STD - - STD 202 - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 6 6 STD - - STD 202 - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 8 8 Sch 20 - - Sch 20 202 - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 10 10 Sch 20 - - Sch 20 202 - - SSSF
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1512C01Z 0063255 Check lift SWE CL800 A105 BB F6 Trm 0.5 1 - - - - - - - SSSF
- 1512D005 0062543 Globe SWE CL800 A105 WB F6/Stell Trm 0.5 1 - - - - - - - SSSF
714 1512G00A 0115373 Gate SWE X FTE CL800 A105 WB F6/Stell Trm 0.5 1 - - - - 102 - - SSSF
521 1512G00B 0061782 Gate SWE CL800 A105 WB F6/Stell Trm 1 1 - - - - 101 - - SSSF
221 1512G00D 0158303 Gate RF CL600 A105 WB F6/Stell Trm Graph Pack 1 1.5 - - - - - - - SSFF
- 1511C00R 0315309 Check swing BE CL600 A216-WCB BB F6/Stell Trm 1.5 1.5 XS - - XS - - - SSSF
- 1512D01J 0341200 Globe BE CL800 A105 WB F6/Stell Trm 1.5 1.5 XS - - XS - - - SSSF
401 1512G02C 0312600 Gate BE CL800 A105 WB F6/Stell Trm 1.5 1.5 XS - - XS - - - SSSF
- 1511B00G 0300990 Ball Shrt RF CL150 A216-WCB 316 Ball PTFE Firesafe 2 4 - - - - - - - SSFF
- 1511D00D 0160461 Globe RF CL150 A216-WCB BB F6/Stell Trm 2 8 - - - - - - - SSFF
- 1511C020 0163450 Check swing RF CL150 A216-WCB BB F6 Trm 2 10 - - - - - - - SSFF
- 1511G002 0156061 Gate RF CL150 A216-WCB BB F6 Trm 2 10 - - - - - - - SSFF
- 1511B00G 1001437 Ball Shrt RF CL150 A216-WCB 316 Ball PTFE Firesafe 2.5 2.5 - - - - - - - SSFF
- 1511B00H 0300984 Ball Shrt RF CL150 A216-WCB 316 Ball PTFE Firesafe GO 6 6 - - - - - - - SSFF F3
All underground pipe and fittings shall be externally coated and wrapped in accordance with SP-50-6. All underground valves shall be installed in valve boxes.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and smaller - Socket Weld 2.5 mm Carbon Steel CL150 FF Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
All underground pipe and fittings shall be externally coated and wrapped in accordance with SP-50-6. All underground valves shall be installed in valve boxes.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and smaller - Socket Weld 2.5 mm Carbon Steel CL150 FF Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
All underground pipe and fittings shall be externally coated and wrapped in accordance with SP-50-6. All underground valves shall be installed in valve boxes.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and smaller - Socket Weld 2.5 mm Carbon Steel CL150 FF Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
All underground pipe and fittings shall be externally coated and wrapped in accordance with SP-50-6. All underground valves shall be installed in valve boxes.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and smaller - Socket Weld 2.5 mm Carbon Steel CL150 FF Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1511B00H Anti-Blowout stem, Firesafe design to API 607, Valves to comply with API-608
1511C00R NPS >=2" to 4" Valves in Hydrocarbons, hydrocarbons with hydrogen, hydrogen or steam service. (Pr-temp limits for steel in hydrogen service in accordance with Nelson Curves). NPS >= 6" Valves in
Steam Service.
1511D00D Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1511G002 Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1512D005 Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated. Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512D01J Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated.
1512G00B Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G00D Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G02C Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1576G008 Nitrile or neoprene bound aramid fibre (cut from sheet). Use only for Hydrant valves and Monitors.
All underground pipe and fittings shall be externally coated and wrapped in accordance with SP-50-6. All underground valves shall be installed in valve boxes.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and smaller - Socket Weld 2.5 mm Carbon Steel CL150 FF Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1576G01T Non metallic gasket/0.8mm fibreglass reinforced polyester sleeves/2sets reinforced phenolic + 2sets steel washers Type F - Non Corrosive service. Non metallic Insulating Gasket shall have following
properties: Dielectric strength (ASTM D149)- 21Kv/mm, Compressive strength (ASTM D625)- 340MPa, Max water absorption (ASTM D229)- 0.1%, Min & Max operating temp- (-17 to 93°C), Hardness
Rockwell M (ASTM D785)- 115, Shear strength (ASTM D732)- 150MPa.
1576G01U Non metallic gasket/0.8mm fibreglass reinforced polyester sleeves/2sets reinforced phenolic + 2sets steel washers Type F - Non Corrosive service. Non metallic Insulating Gasket shall have following
properties: Dielectric strength (ASTM D149)- 21Kv/mm, Compressive strength (ASTM D625)- 340MPa, Max water absorption (ASTM D229)- 0.1%, Min & Max operating temp- (-17 to 93°C), Hardness
Rockwell M (ASTM D785)- 115, Shear strength (ASTM D732)- 150MPa.
1592K000 1.6mm diameter wire. 304SS round bar. Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not acceptable unless solution heat treated after repairs.
All underground pipe and fittings shall be externally coated and wrapped in accordance with SP-50-6. All underground valves shall be installed in valve boxes.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1 and smaller - Socket Weld 2.5 mm Carbon Steel CL150 FF Per SP-90-2A
NPS 1½ and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Pressure: 1960kPa 1960kPa 1920kPa 1770kPa 1580kPa 1380kPa 1210kPa 1020kPa 930kPa 840kPa 740kPa 650kPa
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1541S003 0356234 Pipe PE API-5L-B SMLS 0.5 0.5 XS - - XS 310 - - SSSF
- 1541S003 0356234 Pipe PE API-5L-B SMLS 0.75 0.75 XS - - XS 310 - - SSSF
- 1541S003 0356234 Pipe PE API-5L-B SMLS 1 1 XS - - XS 310 - - SSSF
- 1541S003 0356234 Pipe PE API-5L-B SMLS 1.25 1.25 XS - - XS 310 - - SSSF
- 1541S001 0356234 Pipe BE API-5L-B SMLS 1.5 1.5 XS - - XS - - - SSSF
- 1541X001 0356649 Pipe BE API-5L-B ERW 2 2 STD - - STD - - - SSSF
- 1541X001 0356649 Pipe BE API-5L-B ERW 2.5 2.5 STD - - STD - - - SSSF
- 1541X001 0356649 Pipe BE API-5L-B ERW 3 3 STD - - STD - - - SSSF
- 1541X001 0356649 Pipe BE API-5L-B ERW 4 4 STD - - STD - - - SSSF
- 1541X001 0356649 Pipe BE API-5L-B ERW 6 6 STD - - STD - - - SSSF
857 1541X001 0356650 Pipe BE API-5L-B ERW 8 8 Sch 60 - - Sch 60 1000 959 - SSSF F3
- 1541X001 0356646 Pipe BE API-5L-B ERW 8 8 Sch 20 - - Sch 20 - - - SSSF
- 1541X001 0356646 Pipe BE API-5L-B ERW 10 10 Sch 20 - - Sch 20 - - - SSSF
869 1541X001 0356649 Pipe BE API-5L-B ERW 10 10 STD - - STD - - - SSSF F3
- 1541X001 0356646 Pipe BE API-5L-B ERW 12 12 Sch 20 - - Sch 20 - - - SSSF
- 1541X001 0356645 Pipe BE API-5L-B ERW 14 14 Sch 10 - - Sch 10 - - - SSSF
- 1541X001 0356645 Pipe BE API-5L-B ERW 16 16 Sch 10 - - Sch 10 - - - SSSF
- 1541X001 0356645 Pipe BE API-5L-B ERW 18 18 Sch 10 - - Sch 10 - - - SSSF
- 1541X001 0356645 Pipe BE API-5L-B ERW 20 20 Sch 10 - - Sch 10 - - - SSSF
- 1541X001 0356649 Pipe BE API-5L-B ERW 22 22 STD - - STD - - - SSSF
- 1541X001 0356649 Pipe BE API-5L-B ERW 24 24 STD - - STD - - - SSSF
- 1541X009 0356700 Pipe BE API-5L-B DSAW 26 26 Sch 10* - - Sch 10* - - - SSSF F3
- 1541X009 0356700 Pipe BE API-5L-B DSAW 28 28 Sch 10* - - Sch 10* - - - SSSF F3
- 1541X009 0356700 Pipe BE API-5L-B DSAW 30 30 Sch 10* - - Sch 10* - - - SSSF F3
- 1541X009 0356704 Pipe BE API-5L-B DSAW 40 40 STD - - STD - - - SSSF F3
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1512B01C 1001704 Ball Shrt RF CL300 A105 316SS Fl ball RPTFE WO FB 0.5 0.5 - - - - 833 721 - SSFF
- 1512C00N 0063273 Check lift SWE CL800 A105 WB F6/Stell Trm 0.5 1 - - - - - - - SSSF
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1511D00D Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1511F00A Category B Lug Type, Body A216-WCB, Seat BUNA-N, Disc CS with 304SS seating, Seating Weld Overlay with min thk of 1.6mm, Shaft- 304SS. Valve shall be supplied with Leverlock Positioning handle
to faciliate for valve to be locked in intermediate positions. Valve shall be rated for shut-off at 1035 kPa @ 60°C. Bolt Holes on Lug Pattern Shall be through drilled. Electrostatic feature. Valve Lever Lock
handle shall be furnished with a lockable device that accepts a purchaser-supplied lock to enable valve to be locked in positions. Supplier shall confirm that mating pipework bore will give adequate disc
swing clearance. (Pipe Schedules: 6"-Std, 8-12-S-20, 14-20-S-10, 24"-Std)
1511G002 Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1511G003 Flanges >24" to match ASME B16.47, Series B Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1511G00H Full Bore Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1511W000 Integral seating surfaces; Inconel-X spring; 316 SS Hinge pin / Stop pin / pin retainers / Lug bearings; Single Plate Supplier shall confirm that mating pipework bore will give adequate disc swing clearance.
(Pipe Schedules: 6"-Std, 8-12-S-20, 14-24-S-10)
1512B01C Floating Ball, Full Bore, Top Entry, Anti-Blowout stem, firesafe design, Valves to comply with API-608 Valve seats and seals shall be rated for the same pressue-temperature rating as of the shell, to ASME
B16.34
1512D005 Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated. Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512D01J Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated.
1512D01K Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated. Stem Packing: Compressed Graphite Rings
1512G00B Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G02C Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G02D Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1541X009 Pipes with wall thickness > 20mm shall be delivered in PWHT condition for all welds. (Supplier to ensure the same for all weld seams, circumferential/longitudnal). PSL 1 Grade. All welded pipes shall be
finished only with longitudnal weld seams, helical/spiral seams shall not be acceptable.
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1551W006 For use on Welding Caps, elliptical heads and flat surfaces.
1561B016 Shop Drill & Tap to ASME B1.20.1, 1/2" NPT for Pressure Instrument connections. Tapped Centrally. The threads shall be done in a Sasol approved shop facility. Threads shall conform to ASME B1.20.1
specification for thread form, taper, length & dia of thread. Tolerances on taper, lead & angle of thread shall conform to ASME B1.20.1 for NPT threads. All threads shall be N/C Machined. Supplier shall
conform to requirements from SP-50-13 for material certification, PMI, inspection & testing. PMI shall be in accordance with SP-90-23. 100% Thread Inspection shall be conducted by FW Instrument QC
personnel.
1561L001 Flange drilling to ANSI B16.5, Flange to be supplied complete with matching backing ring per referenced standard. Nominal Bore shall be 25.4mm and Nominal Wall Thickness 14.3mm.
1561P000 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1561P00E Comptabile to ASME B16.47 Series B flanges Shall be manufactured from a single piece material, I.e. the handle or web shall be integral. The Supplier shall include Drawings with dimension details and
calculations for EC/Sasol approval. The blind shall be designed to the specified Class rating and
to withstand leak (pressure) test conditions as per design code.
1561R000 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1561R008 Comptabile to ASME B16.47 Series B flanges Shall be manufactured from a single piece material, I.e. the handle or web shall be integral. The Supplier shall include Drawings with dimension details and
calculations for EC/Sasol approval. The blind shall be designed to the specified Class rating and
to withstand leak (pressure) test conditions as per design code.
1561W00F Flange to be supplied complete with matching backing ring per referenced standard. For details of Ball Joint Facing refer Sasol STDD-5027, Rev 5.
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1576G01L Teflon Gasket/ Nomex- Full length bolt isolating sleeve/ 2 sets high temp phenolic isolating washer + 2 sets steel washer. Type F- Corrosive Hydrocarbon (Max Temp 200°C)
1576G01X Teflon Gasket/ Nomex- Full length bolt isolating sleeve/ 2 sets high temp phenolic isolating washer + 2 sets steel washer. Type F- Corrosive Hydrocarbon (Max Temp 200°C)
1579D004 Flanged Spirax Sarco TD42S2LC or equivalent, Integral SS Y-type strainer with strainer cap. Install in horizontal plane. Traps shall be supplied with Insulating Cover. Traps shall have face to face dimensio
of 210mm. Flanges used for welding to SW connections shall be WNRF. The Supplier shall perform all NDE's and traps to be delivered tested with certified inspection reports. Welding and Inspection
requirements shall be in accordance with Sasol Line Class R.
1579D005 Flanged Spirax Sarco TD42S2 or equivalent, Integral SS Y-type strainer with strainer cap. Install in horizontal plane Traps shall be supplied with Insulating Cover. Traps shall have face to face dimension o
230mm. Flanges used for welding to SW connections shall be WNRF. The Supplier shall perform all NDE's and traps to be delivered tested with certified inspection reports. Welding and Inspection
requirements shall be in accordance with Sasol Line Class R.
1579T001 Model SMC32Y by Spirax Sarco (For Steam Tracing Condensate Return) Trap shall have an SS-Integral Strainer. Trap shall be installed on a horizontal line with strainers positioned in a Horizontal plane.
Traps shall have a face-to-face dimension of 210mm. Flanges used for welding to SW connections shall be WNRF. The supplier shall perform all NDE's and traps delivered tested with certified inspection
reports. Welding and Inspection requirements shall be in accordance with Sasol Line Class R.
1592K000 1.6mm diameter wire. 304SS round bar. Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not acceptable unless solution heat treated after repairs.
1592K004 1.6mm diameter wire. 304SS round bar. Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not acceptable unless solution heat treated after repairs.
1592K005 1.6mm diameter wire. 304SS round bar. Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not acceptable unless solution heat treated after repairs.
1598C005 Female spud with ground joint, Cadmium Plated steel Pipe Threads- NPT(Taper). ASME B.1.20.1.
1598C007 Material- Brass Chicago Coupling. Water/Air service. Male NPT x Quick connector end. Consolidated pneumatic class C15120. Pipe Threads- NPT(Taper). ASME B.1.20.1.
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Pressure: 5110kPa 5110kPa 5010kPa 4660kPa 4510kPa 4380kPa 4190kPa 3980kPa 3870kPa 3760kPa 3640kPa 3470kPa
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1541S003 0356234 Pipe PE API-5L-B SMLS 0.5 0.5 XS - - XS 310 - - SSSF
- 1541S003 0356234 Pipe PE API-5L-B SMLS 0.75 0.75 XS - - XS 310 - - SSSF
- 1541S003 0356234 Pipe PE API-5L-B SMLS 1 1 XS - - XS 310 - - SSSF
- 1541S001 0356234 Pipe BE API-5L-B SMLS 1.5 1.5 XS - - XS - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 2 2 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 2.5 2.5 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 3 3 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 4 4 STD - - STD - - - SSSF
- 1541S001 0356231 Pipe BE API-5L-B SMLS 6 6 STD - - STD - - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 8 8 Sch 20 - - Sch 20 - - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 10 10 Sch 20* - - Sch 20* 217 - - SSSF
838 1541S001 0356233 Pipe BE API-5L-B SMLS 10 10 Sch 80 - - Sch 80 - - - SSSF F3
- 1541S001 0356233 Pipe BE API-5L-B SMLS 10 10 Sch 80 - - Sch 80 217 - - SSSF
- 1541S001 0356228 Pipe BE API-5L-B SMLS 12 12 Sch 20* - - Sch 20* 217 - - SSSF
- 1541S001 0356227 Pipe BE API-5L-B SMLS 14 14 Sch 10* - - Sch 10* 217 - - SSSF
- 1541S001 0356227 Pipe BE API-5L-B SMLS 16 16 Sch 10* - - Sch 10* 217 - - SSSF
- 1541S001 0356227 Pipe BE API-5L-B SMLS 18 18 Sch 10* - - Sch 10* 217 - - SSSF
- 1541S001 0356227 Pipe BE API-5L-B SMLS 20 20 Sch 10* - - Sch 10* 217 - - SSSF
- 1541S001 0356227 Pipe BE API-5L-B SMLS 22 22 Sch 10* - - Sch 10* 217 - - SSSF
- 1541S001 0356227 Pipe BE API-5L-B SMLS 24 24 Sch 10* - - Sch 10* 217 - - SSSF
- 1541X009 0356700 Pipe BE API-5L-B DSAW 26 26 Sch 10* - - Sch 10* 217 - - SSSF F3
- 1541X009 0356700 Pipe BE API-5L-B DSAW 28 28 Sch 10* - - Sch 10* 217 - - SSSF F3
- 1541X009 0356700 Pipe BE API-5L-B DSAW 30 30 Sch 10* - - Sch 10* 217 - - SSSF F3
- 1541X009 0356700 Pipe BE API-5L-B DSAW 32 32 Sch 10* - - Sch 10* 217 - - SSSF F3
- 1541X009 0356700 Pipe BE API-5L-B DSAW 34 34 Sch 10* - - Sch 10* 217 - - SSSF F3
- 1541X009 0356700 Pipe BE API-5L-B DSAW 36 36 Sch 10* - - Sch 10* 217 - - SSSF F3
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1512C00N 0063273 Check lift SWE CL800 A105 WB F6/Stell Trm 0.5 1 - - - - - - - SSSF
Sasol to approve G&H tapping requirement for large bore gate valves as per SP-50-3A. * Wall thickness is to be calculated based on individual design
conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL300 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Sasol to approve G&H tapping requirement for large bore gate valves as per SP-50-3A. * Wall thickness is to be calculated based on individual design
conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL300 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Sasol to approve G&H tapping requirement for large bore gate valves as per SP-50-3A. * Wall thickness is to be calculated based on individual design
conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL300 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Sasol to approve G&H tapping requirement for large bore gate valves as per SP-50-3A. * Wall thickness is to be calculated based on individual design
conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL300 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Sasol to approve G&H tapping requirement for large bore gate valves as per SP-50-3A. * Wall thickness is to be calculated based on individual design
conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL300 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Sasol to approve G&H tapping requirement for large bore gate valves as per SP-50-3A. * Wall thickness is to be calculated based on individual design
conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL300 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Sasol to approve G&H tapping requirement for large bore gate valves as per SP-50-3A. * Wall thickness is to be calculated based on individual design
conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL300 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1511D00E Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1511D00F Flanges >24" to match ASME B16.47, Series B Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler
1511G00S Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
1511G00T Flanges >24" to match ASME B16.47, Series B G&H Tappings (HOLD FOR CONFIRMATION). Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet
Gasket- SPWND with SS-W with Graphite filler.
1511G00V Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated.
1511G03Z Full Bore Full Bore Valve for Hot Tap. Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Bonnet Gasket- SPWND with SS-W with Graphite filler.
Sasol to approve G&H tapping requirement for large bore gate valves as per SP-50-3A. * Wall thickness is to be calculated based on individual design
conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL300 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1512B016 Full Bore, Top Entry, Valves to comply with API-608. Ball-316SS/HC, Seat-316SS/stellite, Body Seal-316SS graphite, Packing-graphite. Firesafe, Blowout Proof Stem. Valve seats and seals shall be rated
for the same pressue-temperature rating as of the shell, to ASME B16.34. Supplier shall provide coating procedure for hard chrome facing to substantiate peeling concerns and Standard body cavity
pressure relief design. Valve in Errosive Service.
1512D005 Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated. Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512D01J Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated.
1512D01K Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated. Stem Packing: Compressed Graphite Rings
1512G00B Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G00D Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G00S Welded Bonnet. Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G02C Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1541X009 Pipes with wall thickness > 20mm shall be delivered in PWHT condition for all welds. (Supplier to ensure the same for all weld seams, circumferential/longitudnal). PSL 1 Grade. All welded pipes shall be
finished only with longitudnal weld seams, helical/spiral seams shall not be acceptable.
1551W006 For use on Welding Caps, elliptical heads and flat surfaces.
Sasol to approve G&H tapping requirement for large bore gate valves as per SP-50-3A. * Wall thickness is to be calculated based on individual design
conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL300 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1561C00M Refer to FWSA Detail Drawing No.26160-8232-030-54-0001 for arrangement of 3 taps. Orientation of taps suitable for both Gases and/or Liquids in the Vertical Flow Direction only.
1561L001 Flange drilling to ANSI B16.5, Flange to be supplied complete with matching backing ring per referenced standard. Nominal Bore shall be 25.4mm and Nominal Wall Thickness 14.3mm.
1561P003 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1561P00D Comptabile to ASME B16.47 Series B flanges Shall be manufactured from a single piece material, I.e. the handle or web shall be integral. The Supplier shall include Drawings with dimension details and
calculations for EC/Sasol approval. The blind shall be designed to the specified Class rating and
to withstand leak (pressure) test conditions as per design code.
1561R001 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral.
1561R007 Comptabile to ASME B16.47 Series B flanges Shall be manufactured from a single piece material, I.e. the handle or web shall be integral. The Supplier shall include Drawings with dimension details and
calculations for EC/Sasol approval. The blind shall be designed to the specified Class rating and
to withstand leak (pressure) test conditions as per design code.
1561W00F Flange to be supplied complete with matching backing ring per referenced standard. For details of Ball Joint Facing refer Sasol STDD-5027, Rev 5.
1576G01X Teflon Gasket/ Nomex- Full length bolt isolating sleeve/ 2 sets high temp phenolic isolating washer + 2 sets steel washer. Type F- Corrosive Hydrocarbon (Max Temp 200°C)
1576G01Z Modified Teflon Gasket (with Glass Microspheres or Silica)/High Temp Full length bolt isolating sleeve/2 sets high temp isolating washer + 2 sets steel washers/Type F- Corrosive Hydrocarbon (Rated for
Max Temp 260ºC)
1579D004 Flanged Spirax Sarco TD42S2LC or equivalent, Integral SS Y-type strainer with strainer cap. Install in horizontal plane. Traps shall be supplied with Insulating Cover. Traps shall have face to face dimensio
of 210mm. Flanges used for welding to SW connections shall be WNRF. The Supplier shall perform all NDE's and traps to be delivered tested with certified inspection reports. Welding and Inspection
requirements shall be in accordance with Sasol Line Class R.
Sasol to approve G&H tapping requirement for large bore gate valves as per SP-50-3A. * Wall thickness is to be calculated based on individual design
conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL300 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1579T001 Model SMC32Y by Spirax Sarco (For Steam Tracing Condensate Return) Trap shall have an SS-Integral Strainer. Trap shall be installed on a horizontal line with strainers positioned in a Horizontal plane.
Traps shall have a face-to-face dimension of 210mm. Flanges used for welding to SW connections shall be WNRF. The supplier shall perform all NDE's and traps delivered tested with certified inspection
reports. Welding and Inspection requirements shall be in accordance with Sasol Line Class R.
1592K001 1.6mm diameter wire. 304SS round bar. Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not acceptable unless solution heat treated after repairs.
1592K008 1.6mm diameter wire. 304SS round bar. Austenitic stainless steel shall be furnished in the solution annealed condition. Weld repairs are not acceptable unless solution heat treated after repairs.
Sasol to approve G&H tapping requirement for large bore gate valves as per SP-50-3A. * Wall thickness is to be calculated based on individual design
conditions.
Construction: Corrosion Allowance: Material: Flange Rating: Stress Relief:
NPS 1" and smaller - Socket Weld 1.0 mm Carbon Steel CL300 RF Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Pressure: 10210kPa 10210kPa 10020kPa 9320kPa 9020kPa 8760kPa 8390kPa 7960kPa 7740kPa 7510kPa 7270kPa 6940kPa 5750kPa 5660kPa
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1541S002 0356033 Pipe PE A106-B SMLS 0.5 0.5 XS - - XS 310 - - SSSF
- 1541S002 0356033 Pipe PE A106-B SMLS 0.75 0.75 XS - - XS 310 - - SSSF
- 1541S002 0356033 Pipe PE A106-B SMLS 1 1 XS - - XS 310 - - SSSF
- 1541S000 0356033 Pipe BE A106-B SMLS 1.5 1.5 XS - - XS - - - SSSF
- 1541S000 0356097 Pipe BE A106-B SMLS 2 2 XS - - XS - - - SSSF
- 1541S000 0356097 Pipe BE A106-B SMLS 3 3 XS - - XS - - - SSSF
- 1541S000 0356097 Pipe BE A106-B SMLS 4 4 XS - - XS - - - SSSF
- 1541S000 0356097 Pipe BE A106-B SMLS 6 6 XS - - XS - - - SSSF
- 1541S000 0356098 Pipe BE A106-B SMLS 8 8 Sch 60* - - Sch 60* 217 - - SSSF
- 1541S000 0356097 Pipe BE A106-B SMLS 10 10 XS* - - XS* 217 - - SSSF
- 1541S000 0356098 Pipe BE A106-B SMLS 12 12 Sch 60* - - Sch 60* 217 - - SSSF
- 1541S000 0356098 Pipe BE A106-B SMLS 14 14 Sch 60* - - Sch 60* 217 - - SSSF
- 1541S000 0356098 Pipe BE A106-B SMLS 16 16 Sch 60* - - Sch 60* 217 - - SSSF
- 1541S000 0356098 Pipe BE A106-B SMLS 18 18 Sch 60* - - Sch 60* 217 - - SSSF
- 1541S000 0356098 Pipe BE A106-B SMLS 20 20 Sch 60* - - Sch 60* 217 - - SSSF
- 1541S000 0356098 Pipe BE A106-B SMLS 22 22 Sch 60* - - Sch 60* 217 - - SSSF
- 1541S000 0356098 Pipe BE A106-B SMLS 24 24 Sch 60* - - Sch 60* 217 - - SSSF
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
714 1512G00A 0115373 Gate SWE X FTE CL800 A105 WB F6/Stell Trm 0.5 1 - - - - 102 310 - SSSF
- 1512C00N 0063273 Check lift SWE CL800 A105 WB F6/Stell Trm 1 1 - - - - - - - SSSF
- 1512D005 0062543 Globe SWE CL800 A105 WB F6/Stell Trm 1 1 - - - - - - - SSSF
- 1512G00B 0061782 Gate SWE CL800 A105 WB F6/Stell Trm 1 1 - - - - - - - SSSF
221 1512D01K 0161610 Globe RF CL600 A105 WB F6/Stell Trm 1 1.5 - - - - 100 - - SSFF
221 1512G02D 0158303 Gate RF CL600 A105 WB F6/Stell Trm 1 1.5 - - - - 127 - - SSFF
- 1512C01P 0351200 Check swing BE CL800 A105 BB F6/Stell Trm 1.5 1.5 XS - - XS - - - SSSF
- 1512D01J 0341200 Globe BE CL800 A105 WB F6/Stell Trm 1.5 1.5 XS - - XS - - - SSSF
- 1512G02C 0312600 Gate BE CL800 A105 WB F6/Stell Trm 1.5 1.5 XS - - XS - - - SSSF
221 1511D00H 0161610 Globe RF CL600 A216-WCB BB F6/Stell Trm 2 4 - - - - 1063 - - SSFF
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1511D00H Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1511D00J Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1511D00L Valves in Steam Service. Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1511D02R Valves in Steam Service. Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless
otherwise stated.
1511G00Z Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1511G010 Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1511G012 Valves in Hydrocarbons, hydrocarbons with hydrogen, hydrogen or steam service. (Pr-temp limits for steel in hydrogen service in accordance with Nelson Curves). Stem Packing- Compressed Graphite
Rings, Manufacturer shall certify maximum stem leakage rate.
1511G03B Valves in Steam Service. Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1511W00A Integral seating surfaces; Inconel-X spring; 316 SS Hinge pin / Stop pin / pin retainers / Lug bearings; Dual Plate Supplier shall confirm that mating pipework bore will give adequate disc swing clearance.
(Pipe Schedules: 2-6"-XS, 8-24"-S60)
1512D005 Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated. Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512D01J Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate. Globe valve Seat design to conform to API 602 paragraph 5.6.3 unless otherwise stated.
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
1512G00B Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G02C Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1512G02D Stem Packing- Compressed Graphite Rings, Manufacturer shall certify maximum stem leakage rate.
1551W006 For use on Welding Caps, elliptical heads and flat surfaces.
1561B018 Shop Drill & Tap to ASME B1.20.1, 1/2" NPT for Pressure Instrument connections. Tapped Centrally. The threads shall be done in a Sasol approved shop facility. Threads shall conform to ASME B1.20.1
specification for thread form, taper, length & dia of thread. Tolerances on taper, lead & angle of thread shall conform to ASME B1.20.1 for NPT threads. All threads shall be N/C Machined. Supplier shall
conform to requirements from SP-50-13 for material certification, PMI, inspection & testing. PMI shall be in accordance with SP-90-23. 100% Thread Inspection shall be conducted by FW Instrument QC
personnel.
1561L001 Flange drilling to ANSI B16.5, Flange to be supplied complete with matching backing ring per referenced standard. Nominal Bore shall be 25.4mm and Nominal Wall Thickness 14.3mm.
1561P001 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral. Blank shall be supplied as a set with Spacer, and vice-versa.
1561P002 Shall be manufactured from a single piece material, I.e. the handle or web shall be integral. Spacer shall be supplied as a set with Blank, and vice-versa.
1561W00F Flange to be supplied complete with matching backing ring per referenced standard. For details of Ball Joint Facing refer Sasol STDD-5027, Rev 5.
1579D006 Flanged Spirax Sarco TD62M or equivalent, Integral SS Y-type strainer with strainer cap. Install in horizontal plane. Application: HP Superheated Steam @ 427°C. Traps shall be supplied with Insulating
Cover. Traps shall have face to face dimension of 210mm. Flanges used for welding to SW connections shall be WNRF. The Supplier shall perform all NDE's and traps to be delivered tested with certified
inspection reports. Welding and Inspection requirements shall be in accordance with Sasol Line Class S.
NPS 1½" and larger - Butt Weld Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.1 ASME B16.5 Per SP-90-2A
Pressure: 10340kPa 10340kPa 10300kPa 9950kPa 9590kPa 9270kPa 8570kPa 8260kPa 8040kPa 7760kPa 7330kPa 6770kPa 6340kPa 6007kPa
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1542S000 0359468 Pipe PE A335-P11 SMLS 0.5 0.5 XS - - XS 310 - - SSSF
- 1542S000 0359468 Pipe PE A335-P11 SMLS 0.75 0.75 XS - - XS 310 - - SSSF
- 1542W000 0359468 Pipe BE A335-P11 SMLS 1 1 XS - - XS - - - SSSF
- 1542W000 0359468 Pipe BE A335-P11 SMLS 1.5 1.5 XS - - XS - - - SSSF
- 1542W000 0359479 Pipe BE A335-P11 SMLS 2 2 STD* - - STD* 217 - - SSSF
- 1542W000 0359479 Pipe BE A335-P11 SMLS 3 3 STD* - - STD* 217 - - SSSF
- 1542W000 0359479 Pipe BE A335-P11 SMLS 4 4 STD* - - STD* 217 - - SSSF
- 1542W000 0359479 Pipe BE A335-P11 SMLS 6 6 STD* - - STD* 217 - - SSSF
- 1542W000 0359479 Pipe BE A335-P11 SMLS 8 8 STD* - - STD* 217 - - SSSF
- 1542W000 0359479 Pipe BE A335-P11 SMLS 10 10 STD* - - STD* 217 - - SSSF
- 1542W000 0359479 Pipe BE A335-P11 SMLS 12 12 STD* - - STD* 217 - - SSSF
- 1542W000 0359479 Pipe BE A335-P11 SMLS 14 14 STD* - - STD* 217 - - SSSF
Valves
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
714 1514G00G 0126711 Gate SWE X FTE CL800 A182-F11 Cl.2 WB F6/Stell Trm 0.5 1.5 - - - - 102 310 - SSSF
221 1516D00Y 0219554 Globe RF CL600 A182-F11 Cl.2 F6/Stell Trm 1 1 - - - - 100 - - SSFF
- 1514C00B 0342682 Check swing BE CL600 A182-F11 Cl.2 WB F6/Stell Trm 1 1.5 XS - - XS - - - SSSF
- 1514D00A 0341237 Globe BE CL600 A182-F11 Cl.2 WB F6/Stell Trm 1 1.5 XS - - XS - - - SSSF
- 1514G00H 0339953 Gate BE CL600 A182-F11 Cl.2 WB F6/Stell Trm 1 1.5 XS - - XS - - - SSSF
221 1514G00J 0216628 Gate RF CL600 A182-F11 Cl.2 BB F6/Stell Trm 1 1.5 - - - - 127 - - SSFF
- 1513D00B 0341233 Globe BE CL600 A217-WC6 BB F6/Stell Trm 2 4 STD* - - STD* 402 - - SSSF
221 1513D00E 0219554 Globe RF CL600 A217-WC6 BB F6/Stell Trm 2 4 - - - - - - - SSFF
221 1513G015 0216656 Gate RF CL600 A217-WC6 BB F6/Stell Trm 2 4 - - - - - - - SSFF
- 1513G016 0339951 Gate BE CL600 A217-WC6 BB F6/Stell Trm 2 4 STD* - - STD* 402 - - SSSF
221 1513C009 0222389 Check swing RF CL600 A217-WC6 BB F6/Stell Trm 2 14 - - - - - - - SSFF
- 1513C00A 0342564 Check swing BE CL600 A217-WC6 BB F6/Stell Trm 2 14 STD* - - STD* - - - SSSF
- 1513D00C 0341234 Globe BE CL600 A217-WC6 BB F6/Stell Trm GO 6 12 STD* - - STD* 402 - - SSSF
221 1513D00F 0341235 Globe RF CL600 A217-WC6 BB F6/Stell Trm GO 6 12 - - - - - - - SSFF
- 1513G017 0339936 Gate BE CL600 A217-WC6 BB F6/Stell Trm GO 6 14 STD* - - STD* 402 - - SSSF
Instrument Connections - Screwed Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.9 ASME B16.5 Per SP-90-2A
Instrument Connections - Screwed Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.9 ASME B16.5 Per SP-90-2A
Instrument Connections - Screwed Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.9 ASME B16.5 Per SP-90-2A
Instrument Connections - Screwed Line class min Test P: Material Group: Press / Temp Rating: Weld quality inspection:
See Isometric Group 1.9 ASME B16.5 Per SP-90-2A
Pipe
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1541S002 0356033 Pipe PE A106-B SMLS 0.5 0.5 XS - - XS - - - SSSF
- 1541S002 0356033 Pipe PE A106-B SMLS 0.75 0.75 XS - - XS - - - SSSF
- 1541S002 0356033 Pipe PE A106-B SMLS 1 1 XS - - XS - - - SSSF
Fittings
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1551H001 0478833 Cap SWE CL3000 A105 0.5 1 - - - - - - - SSSF
- 1551H002 0478830 90 deg elbow SWE CL3000 A105 0.5 1 - - - - 417 - - SSSF
- 1551H003 0478831 45 deg elbow SWE CL3000 A105 0.5 1 - - - - 417 - - SSSF
- 1551H005 0478832 Tee SWE CL3000 A105 0.5 1 - - - - - - - SSSF
- 1551F000 0478832 Reducing tee SWE CL3000 A105 0.75 1 - 0.5 0.75 - - - - SSSF
Pipe Flanges
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
763 1561N000 0601738 SW flange RF X SWE CL150 A105 0.5 1 - - - XS 125 - - SSSF
- 1561N001 0601824 SW flange RF X SWE CL300 A105 0.5 1 - - - XS - - - SSSF
Gaskets
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- 1574S00Q 0672151 GKT CL300 SpW 304-W graph-F CS-CR 304-IR 4.5mm 0.5 1 - - - - 409 - - SSFF
- 1574S00T 0672123 GKT CL150 SpW 304-W graph-F CS-CR 304-IR 4.5mm 0.5 1 - - - - 409 - - SSFF
Bolting
Option FWSA Client Item T max Min Bolt Max Bolt - Min Bolt Max Bolt - Item Notes Fab.
Code Req. No. Code Item Description (°C) Diam(") Diam(") Length Length A B C Cat. Rev
- 1572S000 0675648 Bolting - A193-B7 lub w/A194-2H Stud 0.5 1 - 50 500 - - - - SSFF
Tube
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
0686264 Tube A269-316SS SMLS, Fully Annealed 0.25 0.25 0.035” - - - 1 - - SSFF
0686264 Tube A269-316SS SMLS, Fully Annealed 0.375 0.375 0.035” - - - 1 - - SSFF
0686424 Tube A269-316SS SMLS, Fully Annealed 0.375 0.5 0.049” - - - - - - SSFF
Fittings
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
1553K003 0693324 Male Tube Connector 316SS T x MPT 0.5 0.5 - - - - - - - SSFF
0693325 Female Tube Connector 316SS T x FPT 0.5 0.5 - - - - - - - SSFF
1553K001 Butt Weld Connectors 316SS T x BE 0.5 0.5 0.5 0.5 SSSF
1553K000 Butt Weld Connectors 316SS T x BE 0.5 0.5 - 0.375(T) 0.375(T) -
0693335 Union 316SS Tube x Tube 0.375 0.5 - - - - - - - SSFF
0693336 Reducing Union 316SS Tube x Tube 0.5 0.5 - 0.25 0.375 - - - - SSFF
1553K005 0693329 Tee 316SS Tube x Tube x Tube 0.5 0.5 - - - - - - - SSFF
1516B014 Ball FB Tube Ends 316SS 316 Trim RPTFE seat 0.5 0.5 - - - - - - - SSFF
1516N005 Needle Valve Regulating Typ Tube Ends 316SS 316 Trm PFA Pkg 0.5 0.5 - - - - - - - SSFF
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
Water Soluble (T-3 by THERMON® or equivalent) 320 - - - - 2/3 - -
Pre-Insulated Tubing
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- Pre-Insulated Tubing A269-316SS SMLS Fully Annealed (SL- 220 0.5 0.5 0.049” - - - - - - SSFF
4F149-ATP by THERMON® or equivalent)
For Stainless Steel Steam Tracing only. All tubing and tube fittings shall comply with Sasol Purchase Specification SP-50-15 / SP-50-15I
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- Isolated Tracer Tubing A269-316SS SMLS Fully Annealed (DLS- 220 0.375 0.375 0.049” - - - - - - SSFF
IT-3F49 by THERMON® or equivalent), Sizing and type selection
per Supplier calculations.
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item NotesFab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- Galvanized steel channels 1.2mm Thk, 1200mm LG. 204 - - - - - - 3 - - SSFF
- 1,6mm Dia. Soft Iron Galvanized Tie-Wire. (Temporary for holding - - - - - - 3 - - SSFF
tracer in place prior to installation of channel)
- 15mm x 0,4mm Thk. 304SS Banding (c/w wing type clips). For - - - - - - 3 - - SSFF
securing channel to process pipe.
Miscellaneous – Accessories for Pre-Insulated (Tracer Feed and Tracer Return) and Isolated Tracer Tubing
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- Self-Vulcanising Silicon Rubber Tape & RTV Sealant for
terminations of Pre-Insulated Tubing (Thermotube™ type SL by 220 - - - - - - - - - SSFF
THERMON® or equivalent)
- Self-Vulcanising seal kits for sealing of termination points of
Isolated Tracer Tubing & fixing tape for banding of tubing to 250 - - - - - - - - - SSFF
process pipe (Isolated Tracer type DLS by THERMON®)
Option FWSA Client Item T max Main Size Main Size Main Size Reduced Reduced Reduced Item Notes Fab.
Code Req. No. Code Item Description (°C) Min Max Sch Size Min Size Max Size Sch A B C Cat. Rev
- Mechanical Tube Bender for pre-insulated tubing - - - - - - 3 - - SSFF
- Cable Clamps for securing pre-insulated tubing in cable racks. - - - - - - 3 - - SSFF
- Crimping and Banding tools. - - - - - - 3 - - SSFF
For Stainless Steel Steam Tracing only. All tubing and tube fittings shall comply with Sasol Purchase Specification SP-50-15 / SP-50-15I
Fabrication Category
Abbreviation Description
SSFF Shop supplied, field fabricated
Construction Details
See General Notes, SP-70-03- Section 4)
Thread Compound.......................................(4)
Tubing Bends.............................................. (5)
Pre-Insulated Tubing…………………………Use Manufacturers Standard for bending, end sealing and tube joints. Run from Tracing Manifolds to Tracer and vice-versa.
Isolated Tracer Tubing……………………….Use Manufacturers Standard for bending, end sealing, tube joints and wrapping of tracer on pipes. Run from Steam Tracing Manifolds to Condensate Return Manifolds.
For Stainless Steel Steam Tracing only. All tubing and tube fittings shall comply with Sasol Purchase Specification SP-50-15 / SP-50-15I
SP-90-02A, Rev 1: Requirements For Metallic Fabricated Piping Per Line Class.
The Addendum is for identifying Heat Treatment & NDE Requirements for all New
Line Classes created for Fischer Tropsch Wax Expansion Project.
List of New Line Class created for Fischer Tropsch Wax Expansion Project:
1. A1
2. ANB1
3. ASB1
4. C1
5. CVA
6. YS
W:\Project\Sasol\26160\Gen\08Eng\056pipspec\Piping Material
Specification\WIP_201104\00 26160-000-50A10 Rev F2 (WIP).doc DSN: 10217
FOSTER WHEELER SOUTH AFRICA (PTY) LIMITED
PROJECT TITLE: FT Wax Expansion Project
PROJECT NUMBER: 26160
14. ADDENDUM TO SP-90-02A, REV 1: REQUIREMENTS FOR METALLIC FABRICATED PIPING PER LINE CLASS.
PRE-QUALIFICATION
MATERIAL DESCRIPTION AND SERVICE HEAT TREATMENT
NON-DESTRUCTIVE EXAMINATION REQUIREMENTS (EXTENT AND CONTROLLING NOTES) (GENERAL NOTES: 2, 5, 8 and 9 and UT NOT 81)
IMPACT TEST
LINE CLASS
PRE-HEAT
BUTT & FILLET
NON-PRESS
PWHT
ATTACH
MATERIAL / NON-PRESSURE
SERVICE PRESSURE/T ATTACHMENT AND P- VISUAL RT MT PT BHN
EMP NUMBER
NOTE NOTE SHOP FIELD SHOP FIELD SHOP FIELD SHOP FIELD SHOP FIELD
A1 A/G Fire Water Distribution CS (P-1) CS x x 11 21 100% 100% 0% 0% 41, 42 42 72
Foam CLASS 150 (P-1) 7 7
Low Pressure Nitrogen 0 TO 90°C
Steam (Exhaust)
Water (Cooling)
Water (Utility)
Water (General Factory)
Water (Utility- Clarified ash water)
Nitric Acid 304L SS 304L SS 16 - 100% 100% 10% 20% 53 53
57% Max Concentration (P-8) (P-8) 7 7 31 31
ANB1 CLASS 150
0 TO 93°C
ASME B16.5
ASB1 Impregnated Slurry (0 TO 100°C) 316L SS 316L SS 16 - 100% 100% 5% 10% 51, 52 52
See Note Nitric Acid (Pickling Only, Max Concentration 45%, 0 TO 60°C) (P-8) (P-8) 7 7 31 31
Potassium Nitrate (0 TO 120°C) CLASS 150
Sodium Nitrate (0 TO 120°C) 0 TO 120°C
Note: All Welds including Weld Repairs if any, around the Falling Film Evaporator Piping Loop shall be Solution Annealed. The Inspection Philosophy and NDT techniques shall be as recommended by the Process Licensor. The Heat treatment and NDE requirements listed herein do not apply to the Falling Film Evaporator Piping Loop.
C1 Catalyst Slurry CS (P-1) CS x x 11 21 100% 100% 10% 10% 41, 42, 44 42, 44 71, 72 71
CLASS 300 (P-1) 7 7 6, 31 6, 31
0 TO 285°C
CVA Hot Oil CS (P-1) CS x x 11 21 100% 100% 10% 10% 41, 42, 44 42, 44 71, 72 71
CLASS 300 (P-1) 7 7 31 31
0 TO 400°C
YS SS Steam Tracing (Tubing) 316 SS 316 SS
See Note Tubing (P-8) Compression Tube Fittings
0 TO 320°C
Note: The Temperature limits shown are based on the temperature of the tracing steam or the product line, whichever is greater.