Professional Documents
Culture Documents
304E Mini Hydraulic Excavator TTN00001-UP (MACHINE) (SEBP5979 - 17) - Operating Technique
304E Mini Hydraulic Excavator TTN00001-UP (MACHINE) (SEBP5979 - 17) - Operating Technique
Previous Screen
Welcome: j210hre
Product: MINI HYD EXCAVATOR
Model: 304E MINI HYD EXCAVATOR TTN
Configuration: 304E Mini Hydraulic Excavator TTN00001-UP (MACHINE)
i06529669
Know the maximum height and the maximum reach of your machine.
Serious injury or death by electrocution can occur if the machine or the
work tools are not kept a safe distance from electrical power lines. Keep
a distance of at least 3000 mm (118 inch) plus an additional 10 mm
(0.4 inch) for each 1000 volts over 50000 volts.
Local codes
State codes
NOTICE
When swinging into a ditch, do not use the ditch to stop the swinging
motion. Inspect the machine for damage if the boom is swung into a
bank or an object.
Whenever the tracks of the machine raise off the ground while digging,
lower the machine back to the ground smoothly. DO NOT DROP OR
CATCH IT WITH THE HYDRAULICS. Damage to the machine can
result.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpa… 1/5
4/1/2019 304E Mini Hydraulic Excavator TTN00001-UP (MACHINE)(SEBP5979 - 17) - Documentation
Know the location of any buried cables. Mark the locations clearly before you dig.
Consult your Caterpillar dealer for special bucket tips that are available for use in severe applications.
Move the machine whenever the position for digging is not efficient. The machine can be moved forward or
backward during the operating cycle.
When you operate the machine in close places, utilize the bucket or other work tools to perform the
following functions:
Operating efficiency can be increased by using more than one machine control to perform a task.
Position the truck so that material can be loaded from the rear of the truck or from the side of the truck. Load
the truck evenly so that the rear axles are not overloaded.
An oversize bucket or a bucket that is equipped with blade type side cutters should not be used in rocky
material. These types of buckets slow down the cycle. Damage to the bucket and to other machine
components could result.
Restricted Operation
Illustration 1 g00818695
Soil compaction
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpa… 2/5
4/1/2019 304E Mini Hydraulic Excavator TTN00001-UP (MACHINE)(SEBP5979 - 17) - Documentation
Ground breaking
Demolition
Do not swing the machine while the bucket tips are in the soil.
These operations will damage the boom, the stick, and the bucket and the operations will reduce the life of
the equipment.
Illustration 2 g00818699
Do not use the dropping force of the bucket as a hammer. This will bring excessive force on the rear of the
machine. Possible damage to the machine could result.
Illustration 3 g00818702
If the cylinder is operated at the end of the stroke during operations, excessive force will occur on the stopper
on the inside of the cylinder. This will reduce the life of the cylinder and structures. To avoid this problem,
always leave a small margin of play when the cylinder is operated.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpa… 3/5
4/1/2019 304E Mini Hydraulic Excavator TTN00001-UP (MACHINE)(SEBP5979 - 17) - Documentation
Illustration 4 g00818707
While the bucket is in the ground, do not use the travel force for any excavation. This operation will cause
excessive force on the rear of the machine.
Illustration 5 g00818711
Do not use the dropping force of the rear of the machine for excavation. This operation will damage the
machine.
Operating Precaution
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpa… 4/5
4/1/2019 304E Mini Hydraulic Excavator TTN00001-UP (MACHINE)(SEBP5979 - 17) - Documentation
Illustration 6 g00818715
When deep holes are dug, do not lower the boom so that the bottom side of the boom touches the ground.
When deep holes are dug, do not allow the boom to interfere with the tracks.
Copyright 1993 - 2019 Caterpillar Inc. Mon Apr 01 2019 11:33:48 GMT+0700 (Indochina Time)
All Rights Reserved.
j210hre
Private Network For SIS Licensees.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpa… 5/5