Professional Documents
Culture Documents
LGP32-11P Eax63985401 LG
LGP32-11P Eax63985401 LG
TEST REPORT
IEC/EN 60065
Audio, Video and Similar Electronic Apparatus: Safety Requirements
If this Test Report Form is used by non-IECEE members, the IECEE/IEC logo and the reference to the CB
Scheme procedure shall be removed.
This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and
appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02.
Page 2 of 7 Ref. No. : 10-1330-0817(A2/M1)
(1) Addition of Annex ZB, ZC and Group and national deviation for EN 60065+A11:2008 according to
update of Standard (EN60065:2002+Amd 1:2006 Æ EN60065:2002+Amd 1:2006+Amd 11:2008)
- Note:
The modifications made on the relevant pages are marked with this style.
♦ Factory address:
1. LG Electronics Inc.,
299 GONGDAN-DONG GUMI-SI GYEONGSANGBUK-DO 730-906 KOREA
8. LG Electronics RUS,LLC
Russian Federation
b.9 86km of Minskoe Highway, Rural village Dorokhovskoe, Ruza district Moscow region 143160
9. PT LG Electronics Indonesia
Block GMM2100 Industrial Town, Cikarang Barat, Bekasi Jawa Barat, 17520 Indonesia.
11. LGElectronicsMexicaliS.A.DeC.V
Calle Orbita #36, Parque Industrial, Mexicali II, Mexicali B.C.C.P. 21600 Mexico
General Information
1. Model number covered by the scope of this test report is as follows;
32LK31##, 3 2 L K 3 1 # # - # #, 32LK33##, 3 2 L K 3 3 # # - # #,
1)2) 1)2) 3)4) 1)2) 1)2) 3)4)
32LK45##, 3 2 L K 4 5 # # - # #, 26LK31##, 2 6 L K 3 1 # # - # #,
1)2) 1)2) 3)4) 1)2) 1)2) 3)4)
26LK33##, 26LK33##-##
1)2) 1)2) 3)4)
(The symbols “#” in the model name can be any alphanumeric character or blank ,
not affecting safety.)
2. We tested 32LK310-TA as a basic model for the most severe test conditions.
3. These models are intended to use of internal SMPS power boards as follows;
1) Model no. of SMPS power board: LGP32-11P
- Manufacturer: LG Electronics Inc.
Summary of testing:
- Prepared for Class I apparatus.
- Max. Normal load condition as Max. Bright and Max. Contrast
General remarks:
The test results presented in this report relate only to the object tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory.
”(see Enclosure #)” refers to additional information appended to the report.
”(see appended table)” refers to a table appended to the report.
TEST REPORT
IEC/EN 60065
Audio, Video and Similar Electronic Apparatus: Safety Requirements
If this Test Report Form is used by non-IECEE members, the IECEE/IEC logo and the reference to the CB
Scheme procedure shall be removed.
This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and
appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02.
Page 2 of 7 Ref. No. : 10-1330-0817(A1/M1)
(1) Addition of Annex ZB, ZC and Group and national deviation for EN 60065+A11:2008 according to
update of Standard (EN60065:2002+Amd 1:2006 Æ EN60065:2002+Amd 1:2006+Amd 11:2008)
- Note:
The modifications made on the relevant pages are marked with this style.
♦ Factory address:
1. LG Electronics Inc.,
299 GONGDAN-DONG GUMI-SI GYEONGSANGBUK-DO 730-906 KOREA
8. LG Electronics RUS,LLC
Russian Federation
b.9 86km of Minskoe Highway, Rural village Dorokhovskoe, Ruza district Moscow region 143160
9. PT LG Electronics Indonesia
Block GMM2100 Industrial Town, Cikarang Barat, Bekasi Jawa Barat, 17520 Indonesia.
11. LGElectronicsMexicaliS.A.DeC.V
Calle Orbita #36, Parque Industrial, Mexicali II, Mexicali B.C.C.P. 21600 Mexico
General Information
1. Model number covered by the scope of this test report is as follows;
32LK31##, 3 2 L K 3 1 # # - # #, 32LK33##, 3 2 L K 3 3 # # - # #,
1)2) 1)2) 3)4) 1)2) 1)2) 3)4)
32LK45##, 3 2 L K 4 5 # # - # #, 26LK31##, 2 6 L K 3 1 # # - # #,
1)2) 1)2) 3)4) 1)2) 1)2) 3)4)
(The symbols “#” in the model name can be any alphanumeric character or blank ,
not affecting safety.)
2. We tested 32LK310-TA as a basic model for the most severe test conditions.
3. These models are intended to use of internal SMPS power boards as follows;
1) Model no. of SMPS power board: LGP32-11P
- Manufacturer: LG Electronics Inc.
Summary of testing:
- Prepared for Class I apparatus.
- Max. Normal load condition as Max. Bright and Max. Contrast
General remarks:
The test results presented in this report relate only to the object tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory.
”(see Enclosure #)” refers to additional information appended to the report.
”(see appended table)” refers to a table appended to the report.
IEC SYSTEM FOR MUTUAL RECOGNITION OF TEST CERTIFICATES SYSTEM CEI D'ACCEPTATION MUTUELLE DE CERTIFICATS D'ESSAIS
FOR ELECTRICAL EQUIPMENT (IECEE) CB SCHEME DES EQUIPEMENTS ELECTRIQUES (IECEE) METHODE OC
Rating and principal characteristics AC 100-240 V~, 50/60 Hz, 1.2 A, 120 W, Class I for 32 inch
Valeurs nominales et caractéristiques principales AC 100-240 V~, 50/60 Hz, 1.0 A, 100 W, Class I for 26 inch
Model / Type Ref. 32LK310-TA and variants [see the page 4 of 10-1330-0817(M1)
Ref. De type
Additional information (if neccessary may also be reported on page 2) Original issued : 2010-12-10
Les informations complémentaires (si nécessaire, peuvent être indiqué sur la Certificate KR-4559 is replaced by this version due to addition of annex ZB, ZC
2ème page) and group and national deviation.[see the page 2of 10-1330-0817(M1)]
A sample of Product was tested and found to be in conformity with IEC 60065(ed.7);am1
Un échantillon de ce produit a été essayé et été considéré conforme à la CEI Comments:
+ EN 60065:2002 + Amd 1:2006 + Amd 11:2008
As show in the Test Report Ref. No. which forms part of this certificate 10-1330-0817(M1)
Comme indiqué dans le Rapport d'essais numéro de référence qui constitue
partie de ce certificat
This CB Test Certificate is issued by the National Certification Body: Ce Certificat d'essai OC est établi par l'Organisme National de Certification
IEC SYSTEM FOR MUTUAL RECOGNITION OF TEST CERTIFICATES SYSTEM CEI D'ACCEPTATION MUTUELLE DE CERTIFICATS D'ESSAIS
FOR ELECTRICAL EQUIPMENT (IECEE) CB SCHEME DES EQUIPEMENTS ELECTRIQUES (IECEE) METHODE OC
Additional factory
This CB Test Certificate is issued by the National Certification Body: Ce Certificat d'essai OC est établi par l'Organisme National de Certification
TEST REPORT
IEC/EN 60065
Audio, Video and Similar Electronic Apparatus: Safety Requirements
If this Test Report Form is used by non-IECEE members, the IECEE/IEC logo and the reference to the CB
Scheme procedure shall be removed.
This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and
appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02.
Page 2 of 10 Ref. No. : 10-1330-0817(M1)
(1) Addition of Annex ZB, ZC and Group and national deviation for EN 60065+A11:2008 according to
update of Standard (EN60065:2002+Amd 1:2006 Æ EN60065:2002+Amd 1:2006+Amd 11:2008)
- Note:
The modifications made on the relevant pages are marked with this style.
♦ Factory address:
1. LG Electronics Inc.,
299 GONGDAN-DONG GUMI-SI GYEONGSANGBUK-DO 730-906 KOREA
8. LG Electronics RUS,LLC
Russian Federation
b.9 86km of Minskoe Highway, Rural village Dorokhovskoe, Ruza district Moscow region 143160
9. PT LG Electronics Indonesia
Block GMM2100 Industrial Town, Cikarang Barat, Bekasi Jawa Barat, 17520 Indonesia.
11. LGElectronicsMexicaliS.A.DeC.V
Calle Orbita #36, Parque Industrial, Mexicali II, Mexicali B.C.C.P. 21600 Mexico
General Information
1. Model number covered by the scope of this test report is as follows;
32LK31##, 3 2 L K 3 1 # # - # #, 32LK33##, 3 2 L K 3 3 # # - # #,
1)2) 1)2) 3)4) 1)2) 1)2) 3)4)
32LK45##, 3 2 L K 4 5 # # - # #, 26LK31##, 2 6 L K 3 1 # # - # #,
1)2) 1)2) 3)4) 1)2) 1)2) 3)4)
(The symbols “#” in the model name can be any alphanumeric character or blank ,
not affecting safety.)
2. We tested 32LK310-TA as a basic model for the most severe test conditions.
3. These models are intended to use of internal SMPS power boards as follows;
1) Model no. of SMPS power board: LGP32-11P
- Manufacturer: LG Electronics Inc.
Summary of testing:
- Prepared for Class I apparatus.
- Max. Normal load condition as Max. Bright and Max. Contrast
General remarks:
The test results presented in this report relate only to the object tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory.
”(see Enclosure #)” refers to additional information appended to the report.
”(see appended table)” refers to a table appended to the report.
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
IEC SYSTEM FOR MUTUAL RECOGNITION OF TEST CERTIFICATES SYSTEM CEI D'ACCEPTATION MUTUELLE DE CERTIFICATS D'ESSAIS
FOR ELECTRICAL EQUIPMENT (IECEE) CB SCHEME DES EQUIPEMENTS ELECTRIQUES (IECEE) METHODE OC
Rating and principal characteristics AC 100-240 V~, 50/60 Hz, 1.2 A, 120 W, Class I for 32 inch
Valeurs nominales et caractéristiques principales AC 100-240 V~, 50/60 Hz, 1.0 A, 100 W, Class I for 26 inch
Model / Type Ref. 32LK310-TA and variants [see the page 4 of 10-1330-0817]
Ref. De type
A sample of Product was tested and found to be in conformity with IEC 60065(ed.7);am1
Un échantillon de ce produit a été essayé et été considéré conforme à la CEI Comments:
+ EN 60065:2002 + Amd 1:2006
As show in the Test Report Ref. No. which forms part of this certificate 10-1330-0817
Comme indiqué dans le Rapport d'essais numéro de référence qui constitue
partie de ce certificat
This CB Test Certificate is issued by the National Certification Body: Ce Certificat d'essai OC est établi par l'Organisme National de Certification
IEC SYSTEM FOR MUTUAL RECOGNITION OF TEST CERTIFICATES SYSTEM CEI D'ACCEPTATION MUTUELLE DE CERTIFICATS D'ESSAIS
FOR ELECTRICAL EQUIPMENT (IECEE) CB SCHEME DES EQUIPEMENTS ELECTRIQUES (IECEE) METHODE OC
Additional factory
This CB Test Certificate is issued by the National Certification Body: Ce Certificat d'essai OC est établi par l'Organisme National de Certification
TEST REPORT
IEC/EN 60065
Audio, Video and Similar Electronic Apparatus: Safety Requirements
If this Test Report Form is used by non-IECEE members, the IECEE/IEC logo and the reference to the CB
Scheme procedure shall be removed.
This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and
appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02.
Page 2 of 48 Ref. No. : 10-1330-0817
♦ Factory address:
1. LG Electronics Inc.,
299 GONGDAN-DONG GUMI-SI GYEONGSANGBUK-DO 730-906 KOREA
8. LG Electronics RUS,LLC
Russian Federation
b.9 86km of Minskoe Highway, Rural village Dorokhovskoe, Ruza district Moscow region 143160
9. PT LG Electronics Indonesia
Block GMM2100 Industrial Town, Cikarang Barat, Bekasi Jawa Barat, 17520 Indonesia.
11. LGElectronicsMexicaliS.A.DeC.V
Calle Orbita #36, Parque Industrial, Mexicali II, Mexicali B.C.C.P. 21600 Mexico
General Information
1. Model number covered by the scope of this test report is as follows;
32LK31##, 3 2 L K 3 1 # # - # #, 32LK33##, 3 2 L K 3 3 # # - # #,
1)2) 1)2) 3)4) 1)2) 1)2) 3)4)
32LK45##, 3 2 L K 4 5 # # - # #, 26LK31##, 2 6 L K 3 1 # # - # #,
1)2) 1)2) 3)4) 1)2) 1)2) 3)4)
(The symbols “#” in the model name can be any alphanumeric character or blank ,
not affecting safety.)
2. We tested 32LK310-TA as a basic model for the most severe test conditions.
3. These models are intended to use of internal SMPS power boards as follows;
1) Model no. of SMPS power board: LGP32-11P
- Manufacturer: LG Electronics Inc.
Summary of testing:
- Prepared for Class I apparatus.
- Max. Normal load condition as Max. Bright and Max. Contrast
General remarks:
The test results presented in this report relate only to the object tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory.
”(see Enclosure #)” refers to additional information appended to the report.
”(see appended table)” refers to a table appended to the report.
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
3 GENERAL REQUIREMENTS
Safety class of the apparatus ................................. : Class I P
5 MARKING
Comprehensible and easily discernible On rear side of the enclosure P
Permanent durability against water and petroleum Tested with water and P
spirit petroleum spirit
5.1 Identification, maker, model ................................... : P
,
a), b)
32LK310-TA and variants : see
page 4
c) Class II symbol if applicable This equipment is Class I N
d), e) Rated supply voltage and symbol .......................... : AC 100-240 V~ P
f) Frequency if safety dependant 50/60 Hz P
g), h), i) Rated current or power consumption .................... : 1.2 A, 120 W or 1.0 A, 100 W P
5.2 a) Earth terminal Marked IEC 60417-5019 P
symbol(mains inlet with earth
terminal) :
b) Hazardous live terminals No hazardous live terminals N
c) Supply output terminals (other than mains) No supply output terminals N
5.3 Use of triangle with exclamation mark Marked on the circuit diagram P
5.4 Instructions for use By English P
5.4.1 Mains powered equipment not exposed to dripping Caution wording is written on P
or splashing. Warning concerning objects filled instruction
a)
with liquid, etc.
b) Hazardous live terminals, instructions for wiring No hazardous live terminals N
c) Instructions for replacing lithium battery No lithium battery N
Instructions for modem if fitted No modem N
d) Class I earth connection warning In user’s manual P
e) Instructions for multimedia system connection No such a connection N
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
f) Special stability warning for fixed installation The apparatus is tested to the N
stability requirements of 19.1-3
g) Warning: battery exposure to heat No battery N
h) Warning: protective film on CRT face No CRT N
5.4.2 Disconnect device: plug/coupler or all-pole mains Disconnect device : P
switch location, accessibility and markings Plug/coupler of power supply
cord,
Caution wording is written on
instruction
Instructions for permanently connected equipment This apparatus is not for N
permanently connection
6 HAZARDOUS RADIATION
6.1 Ionizing radiation < 36 pA/kg (0,5 mR/h) No ionizing unit N
6.1 European Council Directive 96/29/Euratom of 13 No ionizing unit N
May 1996 10cm from outer surface of apparatus
EN 60065
<1µSv/h (0,1mR/h)
6.2 Laser radiation, emission limits to IEC 60825-1 .... : No laser unit N
Emission limits under fault conditions .................... : N
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
8.15 No risk of damage to the insulation of internal No hazard : Wires are dressed P
wiring due to hot parts or sharp edges (2N force) away from hot parts or sharp
edges
8.16 Only special supply equipment can be used Not powered by special supply N
8.17 Insulated winding wire without additional N
interleaved insulation
8.18 Endurance test as required by 8.17 N
8.19 Disconnection from the mains P
8.19.1 Disconnect device Type : Mains Plug/coupler P
used
All-pole switch or circuit breaker with >3mm No all-pole switch or circuit N
contact separation breaker
8.19.2 Mains switch ON indication No mains switch N
8.20 Switch not fitted in the mains cord No switch N
8.21 Bridging components comply with clause 14 No bridging N
8.22 Test of non-separable thin sheet material N
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
10 INSULATION REQUIREMENTS
10.1 Insulation resistance (MΩ) at least 2 MΩ min. after > 100 MΩ P
surge test for basic and 4 MΩ min. for reinforced
insulation ................................................................. :
10.2 Humidity treatment 48 h or 120 h ........................... : 120 h, 40 °C, 93 % P
10.3 Insulation resistance and dielectric strength (see appended table) P
between mains terminals
Insulation resistance and dielectric strength across (see appended table) P
BASIC or SUPPLEMENTARY insulation (Class 1)
Insulation resistance across REINFORCED (see appended table) P
insulation (Class II)
11 FAULT CONDITIONS
11.1 No shock hazard under fault condition P
11.2 Heating under fault condition P
No hazard from softening solder P
No flaming more than 10s (see appended table 11.2) P
Soldered terminations not used as protective (see appended table 11.2) P
mechanism
11.2.1 Measurement of temperature rises (see appended table 11.2) P
11.2.2 Temperature rise of accessible parts (see appended table 11.2) P
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
11.2.3 Temperature rise of parts, other than windings, (see appended table 11.2) P
providing electrical insulation
Temperature rise of printed circuit boards (PCB) Not exceeding the limits of N
exceeding the limits of table 3 by max. 100 K for table 3
max. 5 min
a) Temperature rise of printed circuit boards (PCB) N
to 20.1.3, exceeding the limits of table 3 by not
more than 100 K for an area not greater than 2 cm²
b) Temperature rise of printed circuit boards (PCB) N
to 20.1.3 up to 300 K for an area not greater than
2 cm² for a maximum of 5 min
Meets all the special conditions if conductors on N
printed circuit boards are interrupted
Class I protective earthing maintained The continuity of any protective P
Earthing maintained.
11.2.4 Temperature rise of parts acting as a support or P
mechanical barrier
11.2.5 Temperature rise of windings (see appended table 11.2) P
11.2.6 Temperature rise of parts not subject to the limits (see appended table 11.2) P
of 11.2.1 to 11.2.5
12 MECHANICAL STRENGTH
12.1.1 Bump test where mass >7 kg Mass : 9.6 kg, P
No damaged, No hazard
12.1.2 Vibration test (portable, metal, musical amps) Tested : No damaged, No P
hazard
12.1.3 Impact hammer test 0.5 J tested : No damaged, No P
hazard, Withstand 4,240 Vp
Steel ball test (for non-ventilated solid areas) 2 J tested : No damaged, No P
hazard, Withstand 4,240 Vp
12.1.4 Drop test for portable apparatus where mass = 7 Not portable N
kg
12.1.5 Thermoplastic enclosures stress relief test Tested, 70 ºC, 7 h P
12.2 Fixing of knobs, push buttons, keys and levers None N
12.3 Remote controls with hazardous live parts No remote control with live N
12.4 Drawers (pull test 50 N, 10 s) No drawers N
12.5 Antenna coaxial sockets providing isolation Not exist N
12.6 Telescoping or rod antennas construction Not exist N
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
14 COMPONENTS
14.1 Resistors P
a) Resistors between hazardous live parts and No such components N
accessible metal parts
b) Resistors, other than between hazardous live Evaluated in certified power N
parts and accessible parts supply board(LGP32-11P)
(see appended table 14)
b) Resistors separately approved .......................... : R100 P
Evaluated in certified power
supply board(LGP32-11P)
14.2 Capacitors and RC units P
Capacitors separately approved Evaluated in certified power P
supply board(LGP32-11P)
14.2.1 Y capacitors tested to IEC 60384-14, 2nd edition .. : Evaluated in certified power P
supply board(LGP32-11P)
14.2.2 X capacitors tested to IEC 60384-14, 2nd edition .. : Evaluated in certified power P
supply board(LGP32-11P)
14.2.3 Capacitors operating at mains frequency but not Not exist N
connected to the mains: tests for X2 ..................... :
14.2.5 a) Capacitors with volume exceeding 1750 mm³, Evaluated in certified power P
where short-circuit current exceeds 0,2 A: supply board(LGP32-11P)
compliance with IEC60384-1, 4.38 category B or
better ....................................................................... :
b) Capacitors with volume exceeding 1750 mm³, Evaluated in certified power P
mounted closer to a potential ignition source than supply board(LGP32-11P)
table 5 permits: compliance with IEC 60 384-1,
4.38 category B or better ........................................ :
Shielded by a barrier per Table 21 or metal ........... : N
14.3 Inductors and windings P
Comply with IEC 61558-1, IEC 61558-2 N
(as relevant) and clause 20.1.4
14.3.1 Transformers and inductors marked with Evaluated in certified power P
manufacturer’s name and type .............................. : supply board(LGP32-11P)
Transformers and inductors separately approved . : No N
14.3.2 General P
Insulation material complies with clause 20.1.4 Isolating transformer P
14.3.3 Constructional requirements (complete appended P
tables or include manufacturers constructional
insulation descriptions)
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
15 TERMINALS
15.1.1 Mains plug, appliance inlet, interconnection (see appended table 14) P
couplers and mains socket-outlet meet the
appropriate standard
Overloading of plugs or appliance inlets prevented N
if the apparatus has mains socket outlets
Overloading of internal wiring prevented if the N
apparatus has mains socket outlets
15.1.2 Connectors for antenna, earth, audio, video or data: P
No risk of insertion in mains socket-outlets P
No risk of insertion into audio or video: outlets No live terminals and symbol N
marked with the symbol of 5.2
15.1.3 Output terminals of a.c. adaptors or similar devices Not exist N
not compatible with household mains socket-
outlets
15.2 Provision for protective earthing P
Accessible conductive parts of Class I equipment Complied P
reliably connected to earth terminal, within
equipment
Protective earth conductors correctly coloured Green / Yellow wire used P
Equipment with non-detachable mains cord Detachable mains cord used N
provided with separate protective earth terminal
near mains input
Earthing connection of parts removable by hand. N
Protective earth terminal resistant to corrosion P
Earth resistance test: < 0,1 Ω at 25 A ................... : < 0.009 Ω P
15.3 Terminals for external flexible cords and for No such terminals N
permanent connection to the mains supply
15.3.1 Adequate terminals for connection of permanent No permanent wiring N
wiring
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
20 RESISTANCE TO FIRE
20.1 Electrical components and mechanical parts P
a) Exemption for components contained in an P
enclosure of material V-0 to IEC 60695-11-10 with
openings not exceeding 1 mm in width
b) Exemption for small components as defined in N
20.1 mounted on a board of flammability category
of V-1 to IEC 60695-11-10
20.1.1 Electrical components meet the requirements of P
Clause 14 or 20.1.4
20.1.2 Insulation of internal wiring working at voltages Electrical components comply P
> 4 kV or leaving an internal fire enclosure, not with flammability requirements
contributing to the spread of fire in clause 14.
20.1.3 Material of printed circuit boards on which the P
available power exceeds 15 W at a voltage
between 50 V and 400 V (peak) a.c. or d.c. meets
V-1 or better to IEC60707, unless used in a fire
enclosure
Material of printed circuit boards on which the PCB : V-0 used P
available power exceeds 15 W at a voltage >400 V
(see appended table 14)
(peak) a.c. or d.c. meets V-0 to IEC 60707
20.1.4 Components and parts not covered by 20.1.1, PCB : V-0 used P
20.1.2 and 20.1.3 (other than fire enclosures)
(see appended table 14)
mounted nearer to a potential ignition source than
the distances in Table 21 comply with the relevant
flammability category in Table 21
Components and parts as above but shielded from N
a potential ignition source, with the barrier area in
accordance with Table 21 and fig. 13
Apparatus with voltages > 4 kV under normal N
conditions, and distances to enclosure exceed
those specified by Table 21, HB40 min enclosure
20.2 Fire enclosure N
20.2.1 Potential ignition sources with open circuit voltage < 4 kV N
> 4 kV (peak) a.c. or d.c. contained in a fire
enclosure to V-1
20.2.2 Internal fire enclosures with openings not N
exceeding 1 mm in width and with openings for
wires completely filled
20.2.3 Requirements of 20.2.1 and 20.2.2 met by an N
internal fire enclosure
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
AC DC
U1: 0.870 Vpk Arms U1: V mA
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
IC101 pin 1 IC102 pin 3 360 179 2.0 7.5 2.5 7.5
IC101 pin 2 IC102 pin 3 356 178 2.0 7.5 2.5 7.5
IC501 pin 1 IC502 pin 3 352 174 2.0 7.5 2.5 7.5
IC501 pin 2 IC502 pin 3 348 173 2.0 7.5 2.5 7.5
IC502 pin 1 IC503 pin 3 332 162 2.0 7.5 2.5 7.5
IC502 pin 2 IC503 pin 3 332 162 2.0 7.5 2.5 7.5
T101, pin 2 T101, pin 7 410 244 4.2 9.5 5.2 12.5
T101, pin 5 T101, pin 7 330 185 4.2 9.5 5.2 12.5
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
T501, pin 1 T501, pin 8 440 317 4.4 8.0 7.2 8.0
T501, pin 3 T501, pin 8 560 343 4.4 8.0 7.2 8.0
T501, pin 6 T501, pin 8 460 181 4.4 8.0 7.2 8.0
T501, pin 7 T501, pin 8 360 176 4.4 8.0 7.2 8.0
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
Object / part No. manufacturer / Type / model technical data standard mark(s) of
trademark conformity1)
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
Object / part No. manufacturer / Type / model technical data standard mark(s) of
trademark conformity1)
* : According to the manufacturer’s declaration, the unit will be supplied with a power
attachment cord plug and appliance connector which meet the national requirements
and which have been approved to relevant national and international standards.
LCD Panel AU Optronics T260XWYY 26 inch IEC 60065: TUV
Corporation (Y=0-9, A-Z or 2001+A1
blank)
T315HWYY 32 inch IEC 60065: TUV
(Y=0-9, A-Z or 2001+A1
blank)
T315XWYY 32 inch IEC 60065: TUV
(Y=0-9, A-Z or 2001+A1
blank)
IPS VVX32H109G00 32 inch IEC 60065 TUV
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
IEC/EN 60065
Clause Requirement – Test Result - Remark Verdict
4.3.13 Apparatus fitted with voltage selector switch must No voltage selector N
be tested as follows:
Connect apparatus to 230 V ac mains with voltage
selector switch to settings not suitable for
operation at 230 V ac.
7.1, 11.2 Permissible temperature rises of 10 K less than Meets tropical limits P
those specified in Table 2 are required.
Misc. Apparatus enclosure which is shaped and Not shaped like toy. P
decorated so that it is likely to be treated as a toy
by children, shall not be accepted for certification
and registration.