Professional Documents
Culture Documents
Cylinder Liner Projection - Inspect: Testing and Adjusting
Cylinder Liner Projection - Inspect: Testing and Adjusting
1 из 5
Shutdown
Previous Screen
i02162317
Note: The following procedure does not require the use of an H bar to hold the liners while the liner
projection measurements are taken.
The 8T-0455 Liner Projection Tool Group can be used to check the liner projection. Refer to Special
Instruction, SMHS7727, "Use of 8T-0455 Cylinder Liner Projection Indicator Group" for more
information on the use of the tool.
Illustration 1 g01096458
(1) Bolt
(2) Washer
(3) Washer
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/si... 28.11.2007
C-15 Truck Engine 6NZ00001-UP(SEBP3032 - 65) - Document Structure Стр. 2 из 5
(6) Block
Table 1
Needed Components
Item Part Number Description Quantity For One Cylinder Quantity For Six Cylinders
Note: The 7K-1977 Washer is made of a cotton fabric that is impregnated with resin. The washers
will not damage the sealing surface of the cylinder block. These washers are a disposable item. You
may wish to order more washers than the amount that is indicated.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/si... 28.11.2007
C-15 Truck Engine 6NZ00001-UP(SEBP3032 - 65) - Document Structure Стр. 3 из 5
Illustration 2 g
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/si... 28.11.2007
C-15 Truck Engine 6NZ00001-UP(SEBP3032 - 65) - Document Structure Стр. 4 из 5
2. Install the washers. Install all bolts or the six bolts around the liner.
3. Use the 8T-0455 Liner Projection Tool Group to measure the liner projection at "A", "B", "C"
and "D".
5. Add the four readings for each cylinder. Divide the sum by four in order to find the average.
Table 2
Specifications
Note: If the liner projection changes around the liner, turn the liner to a new position within the bore.
If the liner projection is not within specifications, move the liner to a different bore. Inspect the top
face of the cylinder block.
The 138-9381 Spacer Plate should be installed, if all of the liner projection measurements are below
the specifications. The 138-9381 Spacer Plate should also be installed if the liner projection
measurements are low within a range. This spacer plate is 0.076 mm (0.003 inch) thinner than the
regular spacer plate. This spacer plate will increase the liner projection. Use this spacer plate in order
to compensate for low liner projections that are less than 0.076 mm (0.003 inch). Use this spacer
plate if the inspection of the top deck reveals no measurable damage directly under the liner flanges
but the average liner projection is less than 0.076 mm (0.003 inch).
Do not exceed the maximum liner projection of 0.152 mm (0.006 inch). The excessive liner
projection will contribute to cracking of the liner flange.
When the liner projection is correct, put a temporary mark on the liner and the spacer plate. Set the
liners aside.
Note: Refer to Disassembly and Assembly, "Cylinder Liner - Install" for the correct final installation
procedure for the cylinder liners.
Copyright 1993 - 2007 Caterpillar Inc. Wed Nov 28 19:35:49 UTC+0300 2007
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/si... 28.11.2007
C-15 Truck Engine 6NZ00001-UP(SEBP3032 - 65) - Document Structure Стр. 5 из 5
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/si... 28.11.2007