Professional Documents
Culture Documents
Specifi Cations: C32 Acert™ Locomotive Engine
Specifi Cations: C32 Acert™ Locomotive Engine
Locomotive Engine
Specifications
Cat® C32 ACERT™ Locomotive Engine Metric Imperial (English)
Configuration V-12, 4-Stroke-Cycle Diesel
Bore 145 mm 5.71 in
Stroke 162 mm 6.38 in
Displacement 32.1 L 1958.9 in3
Aspiration Twin Turbocharged-Aftercooled (TTA)
Compression Ratio 15.0:1
Rotation (from flywheel end) Counterclockwise
LEHR0019-00 Page 1 of 5
C32 ACERT™
Locomotive Engine
Features
Emissions Testing
Designed to meet EU Stage IIIB locomotive Every engine is full-load tested to ensure proper
emission standards engine performance.
On-engine NOx reduction system with
Product Support Offered Through Global Cat
optimized piston, ring, liner, and fuel system
Dealer Network
configuration to reduce NOx while minimizing
More than 2,200 dealer outlets
in-cylinder sooting
- Caterpillar factory-trained dealer technicians
Aftertreatment features diesel oxidation catalyst
service every aspect of your locomotive engine
Engine Design - Caterpillar parts and labor warranty
Proven reliability and durability of engine and - Preventive maintenance agreements available
aftertreatment for repair-before-failure options
Broad operating speed range
S•O•SSM program matches your oil and coolant
High power density
samples against Caterpillar set standards to
PTO drive options provide flexible access to
determine:
auxiliary power for pumps and other needs
- Internal engine component condition
Low Total Cost of Ownership - Presence of unwanted fluids
Optimized fuel consumption - Presence of combustion by-products
Maintenance-free aftertreatment - Site-specific oil change interval
Advanced Digital Engine Management Over 80 Years of Engine Manufacturing
ADEM™ A4 control system providing integrated Experience
ignition, speed governing, protection, and controls, Ownership of these manufacturing processes
including detonation-sensitive variable ignition enables Caterpillar to produce high quality,
timing. ADEM A4 has improved: user interface, dependable products.
display system, shutdown controls, and system - Cast engine blocks, heads, cylinder liners, and
diagnostics. flywheel housings
- Machine critical components
- Assemble complete engine
LEHR0019-00 Page 2 of 5
C32 ACERT™
Locomotive Engine
Standard Equipment
Aftertreatment Exhaust System
Two DOC canisters remote- or engine-mouted Exhaust dry manifold
Rear-facing or forward-facing exhaust
Air Inlet System
Twin side-mounted turbochargers Fuel System
Air-to-air aftercooled Mechanical Electronic Unit Injection (MEUI)
system
Control System
Primary, secondary, and tertiary fuel filter
Automatic altitude compensation
Electronic fuel priming pump — integrated
Power compensation for fuel temperature
with primary fuel filter base
Electronic diagnostics and fault logging
Fuel transfer pump
Engine monitoring and protection system
(speeds, temperature, pressure); Lube System
J1939 Broadcast (diagnostic, engine Oil cooler — RH
status, and control) Oil filler — RH
ADEM A4 electronic control Oil level gauge — RH
Cooling System Power Take-off
Thermostats and housing SAE A, B, C, & E drives available
Jacket water pump, gear driven, Engine power can also be taken from front of the
centrifugal, RH engine on some applications
Optional Equipment
Air inlet adapters Jacket water heater – 120V and 240V
Battery charger – 10 amp Air inlet shutoff valve
Charging alternator – 24V Freon compressor
Flywheel housing – SAE No. 1 and heavy-duty Digital tachometer
SAE No. 0 J1939 messeger display
Oil pan – high capacity Instrument gauge panel – 24V
Starting motor – dual 24V
Engine Dimensions
2
1
(1) Length — 1819 mm (71.6 in) (2) Width — 1527 mm (60 in) (3) Height — 1442 mm (56.7 in)
Performance Data
Twin Turbocharged-Aftercooled — 1800 rpm
LEHR0019-00 Page 4 of 5
C32 ACERT™
Locomotive Engine
(1) Length — 1819 mm (71.6 in) (2) Width — 1528 mm (60.1 in) (3) Height — 1886 mm (74.2 in)
AFTERTREATMENT DIMENSIONS*
Approximate Size and Weight *Dimensions and image are for individual canister.
(1) Length — 1120 mm (44 in) Two canisters are required. They can be shipped
(2) Width — 400 mm (15.7 in) loose for customizable mounting options.
(3) Height — 440 mm (17.3 in)
Each canister features a single diesel oxidation
Weight — 66 kg (145 lb)
catalyst. Two canisters required to meet emission
Aftertreatment Features standards.
Factory-installed engine-mounted
aftertreatment. Forward exhaust only
applications.
Remote installation options provide OEM
flexibility for many applications. Rear or forward
exhaust applications.
©2015 Caterpillar
LEHR0019-00 (9-15) All rights reserved.