Professional Documents
Culture Documents
Medapoxy Sol 3C: Granitex
Medapoxy Sol 3C: Granitex
MEDAPOXY SOL 3C
Self-leveling epoxy floor coating
The information given in this data sheet is based on our knowledge and our experiment to date. They are given for indication.
It belongs to the customer to ensure that this product suits to the intended usage.
Granitex
Zone industrielle Oued Smar – BP85 Oued Smar – 16270 Alger
Tél : (213) 021 51 66 81 & 82
Fax : (213) 021 51 64 22 & 021 51 65 23
www.granitex.dz - E-mail: granitex@granitex.dz
Data sheets 3 3 0 7
MEDAPOXY SOL 3C
IMPREGNATION
DRYING TIME
On concrete, mortar or tiling surfaces, the primer
MEDA-IMPREGNATION is used to prime 10°C 20°C 30°C
(impregnate) the substrate in order to improve its
characteristics and close the surface porosity to Tack free 10 hr 6 hr 4 hr
avoid the bubbling phenomenon. Accepts light
When MEDA-IMPREGNATION has set for 4 days 2 days 1 day
foot traffic
approximately 6 to 8 hours but no more than 24
hours and is tack free, the MEDAPOXY SOL 3C can Accepts heavy
6 days 5 days 2 days
traffic
be applied. A longer setting will make abrading of
the MEDA-IMPREGNATION necessary for proper Full cure 20 days 17 days 10 days
adhesion.
By hot weather it is necessary to reduce the time of Caution: Full chemical resistance is obtained only
setting of the MEDA-IMPREGNATION. after full cure.
MAINTENANCE
MIXING For maximum life expectancy, routinely sweep and
It is very important to properly mix the three wash floors with conventional cleansers and
components of MEDAPOXY SOL 3C in order to get detergents. All abrasive grit and corrosive spills
a homogeneous mixture and to completely empty should wiped as soon as possible.
the containers in order to ensure the correct mixing
Avoid the use of solvents or thinners based on
ratios.
acetone (MIBK, MEK) and on toluene because they
- Pour the entire contents of component B
can deteriorate the coating aspect.
(hardener) into component A (resin), being
careful not to spill any material. When the surface film of the coating, the gloss or the
- Mix with a Jiffy blade and an electric drill at very color begins to show signs of wear, the dustproofing
low speed for 3 to 5 minutes. quality and resistance of the floor will still remain
- Add progressively component C until getting an intact.
unctuous mortar. Damaged or worn areas of the coating may be
If you do not mix the totality of the package ensure renovated by reapplying MEDAPOXY SOL 3C to
regain original gloss and protection.
you abide to the correct mixing ratio.
PACKAGING AND STORAGE
APPLICATION
Apply using a notched spatula or a spreader. MEDAPOXY SOL 3C is delivered in a 28,5 kg package :
Apply the product at a rate of 1.5 kg / m² Component A: 10 kg
(for a coating thickness of 1 mm). Component B: 3,5 kg
The actual coverage will depend on the texture and Component C : 15 kg
the regularity of the floor. Shelf life is 1 year in unopened containers when
stored in a cool, dry area.
Remove air bubbles carefully using a porcupine roller
to release entrapped air while MEDAPOXY SOL 3C WARNINGS
is wet.
Epoxydic resins can irritate the skin and the mucous
membranes. Consequently, it is advised to put on
rubber gloves.
In case of skin or eye contact, flush with plenty of
water and seek medical attention.
After the application clean tools using an epoxy
thinner (MEDILUPOX) .
The information given in this data sheet is based on our knowledge and our experiment to date. They are given for indication.
It belongs to the customer to ensure that this product suits to the intended usage.
Granitex
Zone industrielle Oued Smar – BP85 Oued Smar – 16270 Alger
Tél : (213) 021 51 66 81 & 82
Fax : (213) 021 51 64 22 & 021 51 65 23
www.granitex.dz - E-mail: granitex@granitex.dz