Professional Documents
Culture Documents
Epas Ncii 11 Pre Test
Epas Ncii 11 Pre Test
Department of Education
Region VI – Western Visayas
SCHOOLS DIVISION OF CAPIZ
Banica, Roxas City
Tel. Number: (036) 620-2371-73, Fax: (036) 621-0974
Website: http://depedcapiz.ph
Multiple Choice.
Direction: Choose the correct answer from the given choices. Write the letter only on your answer sheet.
1. An electronics component must perform its function well and must operate safely. What
characteristics of components is this?
A. Suitable C. Unbreakable
B. Tangible D. Vulnerable
2. This is the information processed or stored by the computer; this may be in the form of text
documents, images, video, clips, or software programs.
A. Android C. Java
B. Data D. Movie
4. A ceramic capacitor has a coded value of 103J, what is its average value in picofarad?
A. 1,000 pF C. 100,000 pF
B. 10,000 pF D. 1,000,000 pF
8. What is used to protect your lungs from inhaling smoke and dust in the workplace?
A. Apron C. Gloves
B. Cap D. Mask
9. What PPE can be used to protect the body from splashes of liquid chemicals?
A. Apron C. Gloves
B. Cap D. Mask
10. What is a circuit with loads connected in series with each other?
A. Compound Circuit C. Parallel Circuit
B. Open Circuit D. Series Circuit
11. What part of the circuit closes and opens the flow of current?
A. Conductor C. Controller
B. Consumer D. Source
13. In testing the continuity of the wire, the ohmmeter must be set in _______________ position.
A. Highest range C. Mid-range
B. Lowest range D. Zero ohms
15. Which of the statements is true in testing Light Emitting Diode at forwarding bias?
A. The L.E.D. breaks during testing
B. The L.E.D. emits light during testing
C. The L.E.D. generate heat during testing
D. The L.E.D. rotates during testing
16. In PCB designing, bigger space is required so that a heat sink can be installed, what design factor is
being considered?
A. Accessibility of Component C. PCB Size and Shape
B. High-Temperature Dissipation D. Space for bolt and nuts
17. The removal of an unnecessary portion or layer of conductive material of Copper Clad?
A. Boring C. Etching
B. Drilling D. Soldering
18. In a bridge-type rectifier circuit, there are four terminal joints. Select the one that could give a DC+
output.
A. Anode-Cathode C. Two Anode
B. Infinite D. Two Cathode
19. What is the stage of the power supply that reduces the amount of ripple voltage and smoothens the
pulsating DC output voltage of the rectifier circuit?
A. Bleeder C. Rectifier Circuit
B. Filter Circuit D. Reserve Circuit
20. To enhance the circuit operation and prevent shortages in a circuit, what should be done in
designing?
A. Check the parts to be installed
B. Check the location of every component
C. Check where to put the input and the output
D. Check for any hairline short in the circuit
22. This is an electric machine that changes applied electrical energy into mechanical action.
A. AC plug C. Buzzer
B. Bell D. Motor
23. Choose the possible reason why the electric fan doesn’t rotate even when energized.
A. The guard mark might be loose
B. The fan blade must be broken
C. The inner pipe might be bended
D. The starting capacitor might be defective
24. What part of the washing machine serves as the passageway out of water?
25. What is the low reactance capacitor that is connected in series with the start winding of an electric
fan?
26. What is a small kitchen appliance that is normally used to toast bread?
27. What part of the flat iron is used to select the amount of heat?
28. What type of wire was used to make filament/ heating elements?
29. What part of the flat iron is the cause if, it overheats?
30. This is a test conducted to check the alignment of the center thermostat and the pan.
31. Choose from the list the possible things to check if the flat iron doesn’t heat.
A. Check the capacity of the water tank
B. Check the preheat time of the flat iron
C. Check the steam knob position of the flat iron
D. Check if the Ac plug is properly connected
32. The Rice cooker is not energized due to busted filament, how to repair it?
A. Reconnect the filament C. Replace the pan
B. Replace the filament D. Realign the filament
34. Subject reassembled units to _____________and cleaning before returning to the costumer.
A. Dissembling C. Pre testing
B. Final testing D. Troubleshooting
35. Upon returning the repaired appliance to the owner, what will you do next?
A. Ask for the payment of your work
B. Conduct pretest of the unit
C. Disassemble the unit for inspection
D. Instruct the owner of the unit operation
36. What type of tools should not be used in the vicinity of charging batteries?
37. This is a chemical device used for the generation and storage of electricity.
A. Cell C. Volts
B. Current D. Watts
A. Ammeter C. Ohmmeter
B. Continuity tester D. Voltmeter
A. Jumping B. Napping
C. Tapping D. Zappin