Professional Documents
Culture Documents
Chỉnh định rơ le 35kV-MP-KL4 22012019
Chỉnh định rơ le 35kV-MP-KL4 22012019
Chỉnh định rơ le 35kV-MP-KL4 22012019
teax
File creation time: 10-10-2018 09:11:19 AM
Name: 7SD86 outgoing
IEC 61850 name: SIP
Type: 7SD86
Product code: 7SD86-JAAA-AA0-0AAAA0-AW1111-13113A-FBA000-000AC0-CH1BA1-CE0
Short product code (TNS): P1B100124
Project name: 77OP-V-100170_V14
Function group Function Function block Setting name Settings group1 Unit Min - Max Step
General
Rated frequency 50 Hz
Minimum operate time 0 s 0 - 60 0.01
Set. format residu. comp. Kr; Kx
Block monitoring dir. off
Station name 77OP-V-100170
No. permis.state changes 0 0 - 65535 1
Initial test time 1 s 1 - 65535 1
No. of chatter tests 0 -1 - 32767 1
Chatter idle time 1 min 1 - 65535 1
Subsequent test time 2 s 2 - 65535 1
Number settings groups 1
Activat. of settings group settings group 1
Blk setting change false
Reserv.time for com.prot. 120 s 0 - 65535 1
Energy restore interval 10 min 0 - 60 1
Energy restore time none
Energy restore latest value
Energy restore by A.time false
Enable sw.auth. station false
Multiple sw.auth. levels false
Specific sw. authorities false
Fault-display with pickup
CFC chart quality handling automatic
Activate device test mode false
Oper.bin.outp. under test false
Time managem.
Date format DD.MM.YYYY
Time zone offset to UTC 60 min -720 - 840 15
Offset daylight sav. time 60 min 0 - 120 15
Switch daylight sav. time true
Last/Sunday/March/02:0
Start of daylight sav. time 0
Last/Sunday/October/03
End of daylight sav. time :00
Time sync.
Fault indication after 600 s 0 - 3600 1
Time source 1 none
Time source 1 port NotUsed
Time source 1 channel NotUsed
Time source 2 none
Time source 2 port NotUsed
Time source 2 channel NotUsed
Time zone time source 1 local
Time zone time source 2 local
Sync. latency time src.1 0 s 0 - 1 1E-08
Sync. latency time src.2 0 s 0 - 1 1E-08
Power system
General
Phase sequence ABC
Meas.point I-3ph 1
CT 3-phase
CT connection 3-phase + IN
Tracking active
Measuring-point ID 1
Rated primary current 1500 A
Rated secondary current 1A
Current range 100 x IR
Internal CT type CT protection
Neutr.point in dir.of ref.obj yes
Inverted phases none
CT error changeover 1 1 - 10 0.01
CT error A 5.00% 0.50% - 50.00% 0.10%
CT error B 15.00% 0.50% - 50.00% 0.10%
CT 1
Magnitude correction 1 0.01 - 10 0.001
Phase IA
CT 2
Magnitude correction 1 0.01 - 10 0.001
Phase IB
CT 3
Magnitude correction 1 0.01 - 10 0.001
Phase IC
CT 4
Magnitude correction 1 0.01 - 10 0.001
Phase IN
Brk.wire det.
Mode on
Mode of blocking blocking
Delta value for autoblock 1 0.004 - 5 0.001
Supv. balan. I
Mode on
Release threshold 500 A 30 - 35000 1
Unrestricted
Function group Function Function block Setting name Settings group1 Unit Min - Max Step
Threshold min/max 0.5 0.1 - 0.95 0.01
Delay failure indication 5 s 0 - 100 0.01
Supv. ph.seq.I
Mode on
Delay failure indication 5 s 0 - 100 0.01
Supv. sum I
Mode on
Threshold 100 A 30 - 10000 1
Slope factor 0.1 0 - 0.95 0.01
Delay failure indication 5 s 0 - 100 0.01
Supv.ADC sum I
Mode on
Saturat. det.
Mode on
CT saturation threshold 8000 A 1200 - 100000 0
Meas.point V-3ph 1
VT 3-phase
Rated primary voltage 35000 V
Rated secondary voltage 110 V
VT connection 3 ph-to-gnd voltages
Inverted phases none
Tracking active
Measuring-point ID 2
VT 1
Magnitude correction 1 0.01 - 10 0.001
Phase VA
VT 2
Magnitude correction 1 0.01 - 10 0.001
Phase VB
VT 3
Magnitude correction 1 0.01 - 10 0.001
Phase VC
VT 4
Supv. balan. V
Mode on
Release threshold 17500 V 1200 - 680000 10
Threshold min/max 0.75 0.58 - 0.95 0.01
Delay failure indication 5 s 0 - 100 0.01
Supv. ph.seq.V
Mode on
Delay failure indication 5 s 0 - 100 0.01
Supv. sum V
Mode off
Threshold 17500 V 1200 - 680000 10
Delay failure indication 5 s 0 - 100 0.01
VT miniatureCB
Response time 0 s 0 - 0.03 0.01
Meas.point V-1ph 1
General
Rated primary voltage 35000 V
Rated secondary voltage 110 V
Tracking inactive
Measuring-point ID 3
VT 1
Magnitude correction 1 0.01 - 10 0.001
Phase V AB
VT miniatureCB
Response time 0 s 0 - 0.03 0.01
Recording
Fault recording with pickup
Storage always
Maximum record time 5 s 0.2 - 80 0.01
Pre-trigger time 0.5 s 0.05 - 16 0.01
Post-trigger time 0.5 s 0.05 - 16 0.01
Manual record time 0.5 s 0.2 - 80 0.01
Sampling frequency 2 kHz
Sampl. freq. IEC61850 rec. 1 kHz
COMTRADE revision year COMTRADE 1999
Scaling COMTRADE Secondary values
Cal.zero.seq.cur.channel no
Cal.zero seq.volt.channel no
Line 1
General
Rated current 1500 A
Rated voltage 35000 V
Rated apparent power 90930000 VA
Neutral point grounded
C1 per length unit 0.0000000025 F/km 0 - 0.025 1E-09
C0 per length unit 0.0000000025 F/km 0 - 0.025 1E-09
X per length unit 0.21 Ω/km 0.002 - 38 0.0001
Line length 600 m 100 - 1000000 10
Line angle 85 ° 10 - 89 0.01
Kr 1 -0.33 - 11 0.01
Kx 1 -0.33 - 11 0.01
CT saturation detection no
Series compensation no
Series capacit. reactance 0 Ω 0 - 2400 0.001
P, Q sign not reversed
Fault locator
Mode on
Start with going pickup
Load compensation no
Unrestricted
Function group Function Function block Setting name Settings group1 Unit Min - Max Step
Mes.v.fail.det
Mode on
Asym.fail.-DO on netw.flt. no
Asym.fail. - time delay 10 s 0 - 30 0.01
3ph.fail. - phs.curr.release 100 A 30 - 35000 1
3ph.fail. - phs.curr. jump 100 A 30 - 35000 1
3ph.fail. - VA,VB,VC < 20000 V 1200 - 1360000 10
Switch-on 3ph. failure on
SO 3ph.fail. - time delay 3 s 0.01 - 30 0.01
50/51 OC-3ph-A1
General
Emergency mode caused by main prot.
Group indicat.
Definite-T 1
Mode off
Operate & flt.rec. blocked no
1-pole operate allowed no
Dynamic settings no
Method of measurement fundamental comp.
Threshold 1710 A 30 - 35000 1
Dropout ratio 0.95 0.9 - 0.99 0.01
Pickup delay 0 s 0 - 60 0.01
Dropout delay 0 s 0 - 60 0.01
Operate delay 0 s 0 - 100 0.01
Definite-T 2
Mode off
Operate & flt.rec. blocked no
1-pole operate allowed no
Dynamic settings no
Method of measurement fundamental comp.
Threshold 1500 A 30 - 35000 1
Dropout ratio 0.95 0.9 - 0.99 0.01
Pickup delay 0 s 0 - 60 0.01
Dropout delay 0 s 0 - 60 0.01
Operate delay 0.5 s 0 - 100 0.01
50N/51N OC-gnd-A1
General
Emergency mode caused by main prot.
Measured value IN measured
Group indicat.
Definite-T 1
Mode off
Operate & flt.rec. blocked no
Dynamic settings no
Method of measurement fundamental comp.
Threshold 1710 A 10 - 35000 1
Dropout ratio 0.95 0.9 - 0.99 0.01
Dropout delay 0 s 0 - 60 0.01
Operate delay 0.3 s 0 - 60 0.01
Definite-T 2
Mode on
Operate & flt.rec. blocked no
Dynamic settings no
Method of measurement fundamental comp.
Threshold 1500 A 10 - 35000 1
Dropout ratio 0.95 0.9 - 0.99 0.01
Dropout delay 0 s 0 - 60 0.01
Operate delay 0.5 s 0 - 60 0.01
67 Dir.OC-3ph-A1
General
Emergency mode no
Rotation angle of ref. volt. 45 ° -180 - 180 1
Group indicat.
Definite-T 1
Mode on
Operate & flt.rec. blocked no
Directional mode forward
Method of measurement RMS value
at volt.< & mem.empty
Non-directional pickup
Directional comparison no
Release via input signal no
Blk. by meas.-volt. failure yes
Dynamic settings no
Threshold 1710 A 30 - 35000 1
Dropout ratio 0.95 0.9 - 0.99 0.01
Dropout delay 0 s 0 - 60 0.01
Operate delay 0.3 s 0 - 60 0.01
Definite-T 2
Mode on
Operate & flt.rec. blocked no
Directional mode forward
Method of measurement fundamental comp.
at volt.< & mem.empty
Non-directional pickup
Directional comparison no
Release via input signal no
Blk. by meas.-volt. failure yes
Dynamic settings no
Threshold 1500 A 30 - 35000 1
Dropout ratio 0.95 0.9 - 0.99 0.01
Dropout delay 0 s 0 - 60 0.01
Unrestricted
Function group Function Function block Setting name Settings group1 Unit Min - Max Step
Operate delay 0.5 s 0 - 60 0.01
Inverse-T 1
Mode off
Operate & flt.rec. blocked no
Directional mode forward
Method of measurement fundamental comp.
Non-directional pickup at volt.< & mem.empty
Directional comparison no
Release via input signal no
Blk. by meas.-volt. failure yes
Dynamic settings no
Threshold 1500 A 30 - 35000 1
Type of character. curve IEC normal inverse
Min. time of the curve 0 s 0 - 1 0.01
Reset disk emulation
Time dial 1 0 - 15 0.01
Additional time delay 0 s 0 - 60 0.01
67N GFP gnd.sys.1
General
Polarization with V0 + IY or V2 + I2
Angle forward α 338 ° 0 - 360 1
Angle forward β 122 ° 0 - 360 1
Min. zero-seq. voltage V0 2800.231 V 600 - 136000 10
Dir.reslt=forw.at V0<min no
Min.3I0 f.increas.dir.sens. 30 A 30 - 10000 1
Min. neg.-seq. voltage V2 2800.231 V 600 - 136000 10
Min. neg.-seq. current I2 50 A 30 - 10000 1
Dir.corr.at ser.comp.lines no
Group indicat.
Definite-T 1
Mode off
Operate & flt.rec. blocked no
Directional mode non-directional
Method of measurement 1-cycle filter
Op.mode at 1p dead time blocked
Hold mode 1p dead time 0.04 s 0 - 60 0.001
Dynamic settings no
Stabiliz. w. phase current 10.00% 0.00% - 30.00% 1.00%
Threshold 1710 A 30 - 35000 1
Operate delay 0.3 s 0 - 60 0.001
Definite-T 2
Mode off
Operate & flt.rec. blocked no
Directional mode non-directional
Method of measurement 1-cycle filter
Op.mode at 1p dead time blocked
Hold mode 1p dead time 0.04 s 0 - 60 0.001
Dynamic settings no
Stabiliz. w. phase current 10.00% 0.00% - 30.00% 1.00%
Threshold 1500 A 30 - 35000 1
Operate delay 0.5 s 0 - 60 0.001
87 Line diff. prot.
General
Mode on
Min. current for release 0 A 0 - 35000 1
Supervision Idiff yes: block diff. prot.
I-DIFF
Mode on
Operate & flt.rec. blocked no
Threshold 450 A 100 - 20000 1
Thresh. switch onto fault 450 A 100 - 20000 1
Operate delay 0.04 s 0 - 60 0.01
I-DIFF fast 2
Mode on
Operate & flt.rec. blocked no
Threshold 1500 A 500 - 100000 1
Thresh. switch onto fault 1500 A 500 - 100000 1
49 Th.overl.-A 1
49 Th.overl. 1
Mode on
Operate & flt.rec. blocked no
Threshold current warning 1313 A 30 - 35000 1
Threshold thermal warn. 90.00% 50.00% - 100.00% 1.00%
Dropout threshold operate 90.00% 50.00% - 99.00% 1.00%
Emerg. start T overtravel 15 s 0 - 15000 10
K-factor 1.05 0.1 - 4 0.01
Thermal time constant 900 s 10 - 60000 1
Cooling time constant 3600 s 10 - 60000 1
Imax thermal 2500 A 30 - 10000 1
Imin cooling 500 A 0 - 10000 1
Temperature rise at Irated 70 K 40 - 200 1
Storage of thermal replica no
Behav. at I> Imax therm. current limiting
Default temperature 40 °C -55 - 55 1
Minimal temperature -20 °C -55 - 40 1
27 Undervolt.-3ph 1
General
Current-flow criterion on
Threshold I> 50 A 30 - 10000 1
Group indicat.
Definite-T 1
Unrestricted
Function group Function Function block Setting name Settings group1 Unit Min - Max Step
Mode on
Operate & flt.rec. blocked no
Blk. by meas.-volt. failure yes
Measured value phase-to-phase
Method of measurement fundamental comp.
Pickup mode 1 out of 3
Pickup delay no
Threshold 21000 V 1200 - 700000 10
Dropout ratio 1.05 1.01 - 1.2 0.01
Operate delay 3 s 0 - 60 0.01
Definite-T 2
Mode off
Operate & flt.rec. blocked no
Blk. by meas.-volt. failure yes
Measured value phase-to-phase
Method of measurement fundamental comp.
Pickup mode 1 out of 3
Pickup delay no
Threshold 260000 V 1200 - 700000 10
Dropout ratio 1.05 1.01 - 1.2 0.01
Operate delay 0.5 s 0 - 60 0.01
59 Overvolt.-3ph 1
Group indicat.
Definite-T 1
Mode off
Operate & flt.rec. blocked no
Measured value phase-to-phase
Method of measurement fundamental comp.
Pickup mode 1 out of 3
Threshold 45000 V 1200 - 1360000 10
Dropout ratio 0.95 0.9 - 0.99 0.01
Operate delay 0.5 s 0 - 300 0.01
Definite-T 2
Mode off
Operate & flt.rec. blocked no
Measured value phase-to-phase
Method of measurement fundamental comp.
Pickup mode 1 out of 3
Threshold 525000 V 1200 - 1360000 10
Dropout ratio 0.95 0.9 - 0.99 0.01
Operate delay 0.3 s 0 - 300 0.01
Circuit breaker 1
General
Rated normal current 1500 A
Rated voltage 350000 V
Current thresh. CB open 100 A 30 - 10000 1
Trip logic
Reset of trip command with I<
Circuit break.
Output time 0.1 s 0.02 - 1800 0.01
Indicat. of breaking values always
Manual close
Action time 0.3 s 0.01 - 60 0.01
CB open dropout delay 0 s 0 - 60 0.01
Reset LED Group
Control
Control model SBO w. enh. security
SBO time-out 30 s 0.01 - 1800 0.01
Feedback monitoring time 1 s 0.01 - 1800 0.01
Check switching authority yes
Check if pos. is reached yes
Check double activat. blk. yes
Check blk. by protection yes
Interlocking
CB test
Dead time 0.1 s 0 - 60 0.01
Trip only false
Consider current criterion false
50BF Ad.CBF 1
Mode on
Holding int. start signal yes
Start via binary input no
CB aux.cont. crit. allowed no
with effective criterion
Dropout
Retrip after T1 no
Threshold phase current 225 A 30 - 35000 1
Threshold sensitive 225 A 30 - 35000 1
Delay T1 for 3-pole retrip 0.05 s 0 - 60 0.001
Delay T2 for 3-pole trip 0.13 s 0.05 - 60 0.001
Minimum operate time 0.1 s 0 - 60 0.01
3I0 criterion Plausibility check
I2 criterion Plausibility check
Threshold 3I0 dir. release 225 A 30 - 35000 1
Threshold I2 dir. release 225 A 30 - 35000 1
25 Synchronization
General
Angle adjust. (transform.) 0 ° -179 - 180 0.1
Synchrocheck 1
Mode on
Min. operating limit Vmin 7000 V 1200 - 1360000 10
Max. operat. limit Vmax 36750 V 1200 - 1360000 10
Unrestricted
Function group Function Function block Setting name Settings group1 Unit Min - Max Step
Max.durat. sync.process 30 s 0 - 3600 0.01
Direct close command no
Voltage adjustment 1 0.5 - 2 0.001
Close cmd. at V1< & V2> no
Close cmd. at V1> & V2< no
Close cmd. at V1< & V2< no
V1, V2 without voltage 7000 V 1200 - 680000 10
V1, V2 with voltage 24500 V 1200 - 1360000 10
Supervision time 0.1 s 0 - 60 0.01
Max. voltage diff. V2>V1 24500 V 0 - 680000 10
Max. voltage diff. V2<V1 24500 V 0 - 680000 10
Max. frequency diff. f2>f1 0.1 Hz 0 - 2 0.001
Max. frequency diff. f2<f1 0.1 Hz 0 - 2 0.001
Max. angle diff. α2>α1 10 ° 0 - 90 1
Max. angle diff. α2<α1 10 ° 0 - 90 1
Sychr./Asycr.1
Mode off
Min. operating limit Vmin 360000 V 1200 - 1360000 10
Max. operat. limit Vmax 440000 V 1200 - 1360000 10
Max.durat. sync.process 30 s 0 - 3600 0.01
Direct close command no
Voltage adjustment 1 0.5 - 2 0.001
Close cmd. at V1< & V2> no
Close cmd. at V1> & V2< no
Close cmd. at V1< & V2< no
V1, V2 without voltage 20000 V 1200 - 680000 10
V1, V2 with voltage 320000 V 1200 - 1360000 10
Supervision time 0.1 s 0 - 60 0.01
Async. operating mode on
CB make time 0.06 s 0.01 - 0.6 0.01
Max. voltage diff. V2>V1 20000 V 0 - 680000 10
Max. voltage diff. V2<V1 20000 V 0 - 680000 10
Max. frequency diff. f2>f1 0.1 Hz 0 - 4 0.001
Max. frequency diff. f2<f1 0.1 Hz 0 - 4 0.001
Sync. operating mode on
f-threshold ASYN<->SYN 0.01 Hz 0.01 - 0.2 0.001
Max. voltage diff. V2>V1 20000 V 0 - 680000 10
Max. voltage diff. V2<V1 20000 V 0 - 680000 10
Max. angle diff. α2>α1 10 ° 0 - 90 1
Max. angle diff. α2<α1 10 ° 0 - 90 1
Delay close command 0 s 0 - 60 0.01
Unrestricted
1SW3
50 Hz
0
Kr; Kx
off
77OP-V-100170
0
1
0
1
2
1
settings group 1
false
120
10
none
latest value
x
x
x
x
x
automatic
false
false
x
x
x
x
x
600
SNTP
Port F
x
IRIG-B
Port G
x
UTC
UTC
x
x
ABC
3-phase + IN
active
1
1500
1A
100 x IR
CT protection
yes
none
1
5.00%
15.00%
1
IA
1
IB
1
IC
1
IN
on
blocking
1
on
500
Unrestricted
1SW3
0.5
5
on
5
on
100
0.1
5
on
on
7500
35000
110
3 ph-to-gnd voltages
none
active
2
1
VA
1
VB
1
VC
on
17500
0.75
5
on
5
off
17500
5
35000
110
inactive
3
1
V AB
with pickup
always
5
0.5
0.5
0.5
2 kHz
1 kHz
COMTRADE 1999
Secondary values
no
no
1500
35000
90930000
grounded
0.0000000010
0.0000000010
0.99
600
85
1
1
no
no
0
not reversed
on
with going pickup
no
Unrestricted
1SW3
on
no
10
100
100
6363
on
3
off
no
no
no
fundamental comp.
1710
0.95
0
0
0
off
no
no
no
fundamental comp.
1500
0.95
0
0
0.5
off
no
no
fundamental comp.
1710
0.95
0
0.3
on
no
no
fundamental comp.
1500
0.95
0
0.5
no
45
on
no
forward
RMS value
at volt.< & mem.empty
yes
no
yes
no
1710
0.95
0
0.3
on
no
forward
fundamental comp.
at volt.< & mem.empty
yes
no
yes
no
1500
0.95
0
Unrestricted
1SW3
0.5
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
V0 + IY or V2 + I2
338
122
2800.231
no
45
2800.231
50
no
off
no
non-directional
1-cycle filter
blocked
0.04
no
10.00%
1710
0.3
off
no
forward
1-cycle filter
blocked
0.04
no
10.00%
1500
0.5
on
0
yes: block diff. prot.
off
no
450
450
0.04
off
no
1500
1500
on
no
1313
90.00%
90.00%
20
1.05
900
3600
2500
500
70
no
current limiting
40
-20
on
50
Unrestricted
1SW3
on
no
yes
phase-to-phase
fundamental comp.
1 out of 3
no
21000
1.05
3
x
x
x
x
x
x
x
x
x
x
off
no
phase-to-phase
fundamental comp.
1 out of 3
44959
0.95
0.5
x
x
x
x
x
x
x
x
1500
350000
100
with I<
0.1
always
0.3
0
0.1
false
false
on
yes
no
no
with effective criterion
no
285
285
0.05
0.13
0.1
Plausibility check
Plausibility check
285
285
on
7000
36750
Unrestricted
1SW3
30
no
1
yes
yes
yes
7000
24500
0.1
2450
2450
0.1
0.1
10
10
off
36000
44000
30
no
1
no
no
no
2000
32000
0.1
on
0.06
2000
2000
0.1
0.1
on
0.01
2000
2000
10
10
0
Unrestricted
Name of imported TEA-X file: Transformer CFG_7UM85.teax
File creation time: 09-10-2018 10:09:08 AM
Name: 7UM85
IEC 61850 name: H01R01_7UM
Type: 7UM85
Product code: 7UM85-DAAA-AA0-0AAAA0-AH0111-12111B-AAA000-000AC0-CH1BA1-CC1
Short product code (TNS): P1L9791
Project name: 77OP-V-100170_V14
Function group Function Function block Setting name Settings group1 Unit Min - Max Step
General
Rated frequency 50 Hz
Minimum operate time 0 s 0 - 60 0.01
Set. format residu. comp. Kr; Kx
Block monitoring dir. off
Reserv.time for com.prot. 120 s 0 - 65535 1
No. permis.state changes 0 0 - 65535 1
Initial test time 1 s 1 - 65535 1
No. of chatter tests 0 -1 - 32767 1
Chatter idle time 1 min 1 - 65535 1
Subsequent test time 2 s 2 - 65535 1
Number settings groups 1
Activat. of settings group settings group 1
Blk setting change false
Enable sw.auth. station false
Multiple sw.auth. levels false
Specific sw. authorities false
Fault-display with pickup
CFC chart quality handling automatic
Activate device test mode false
Oper.bin.outp. under test false
Device
Alarm handling
Time managem.
Date format DD.MM.YYYY
Time zone offset to UTC 60 min -720 - 840 15
Offset daylight sav. time 60 min 0 - 120 15
Switch daylight sav. time true
Last/Sunday/March/0
Start of daylight sav. time
2:00
Last/Sunday/October/
End of daylight sav. time
03:00
Time sync.
Fault indication after 600 s 0 - 3600 1
Time source 1 none
Time source 1 port NotUsed
Time source 1 channel NotUsed
Time source 2 none
Time source 2 port NotUsed
Time source 2 channel NotUsed
Time zone time source 1 local
Time zone time source 2 local
Sync. latency time src.1 0 s 0 - 1 1E-08
Sync. latency time src.2 0 s 0 - 1 1E-08
Power system
General
Phase sequence ABC
3TA
CT 3-phase
CT connection 3-phase + IN
Tracking active
Measuring-point ID 1
Rated primary current 1500 A
Rated secondary current 5A
Current range 100 x IR
Internal CT type CT protection
Neutr.point in dir.of ref.obj yes
Inverted phases none
CT 1
Magnitude correction 1 0.01 - 10 0.001
Phase IA
CT 2
Magnitude correction 1 0.01 - 10 0.001
Phase IB
CT 3
Magnitude correction 1 0.01 - 10 0.001
Phase IC
CT 4
Magnitude correction 1 0.01 - 10 0.001
Phase IN
Brk.wire det.
Supv. balan. I
Mode off
Release threshold 750 A 45 - 52500 1
Unrestricted
Function group Function Function block Setting name Settings group1 Unit Min - Max Step
Threshold min/max 0.5 0.1 - 0.95 0.01
Delay failure indication 5 s 0 - 100 0.01
Supv. ph.seq.I
Mode off
Delay failure indication 5 s 0 - 100 0.01
Supv. sum I
Mode off
Threshold 150 A 45 - 15000 1
Slope factor 0.1 0 - 0.95 0.01
Delay failure indication 5 s 0 - 100 0.01
Supv.ADC sum I
Mode off
PT1
VT 3-phase
Rated primary voltage 35000 V
Rated secondary voltage 110 V
Matching ratio Vph / VN 1.73
3 ph-to-gnd volt. +
VT connection
VN
Inverted phases none
Tracking active
Measuring-point ID 3
VT 1
Magnitude correction 1 0.01 - 10 0.001
Phase VA
VT 2
Magnitude correction 1 0.01 - 10 0.001
Phase VB
VT 3
Magnitude correction 1 0.01 - 10 0.001
Phase VC
VT 4
Magnitude correction 1 0.01 - 10 0.001
Phase VN
Supv. balan. V
Mode on
Release threshold 17500 V 95 - 59500 1
Threshold min/max 0.75 0.58 - 0.95 0.01
Delay failure indication 5 s 0 - 100 0.01
Supv. ph.seq.V
Mode on
Delay failure indication 5 s 0 - 100 0.01
Supv. sum V
Mode off
Threshold 8749.999 V 95 - 59500 1
Delay failure indication 5 s 0 - 100 0.01
VT miniatureCB
Response time 0 s 0 - 0.03 0.01
7TA
CT 3-phase
CT connection 3-phase + IN
Tracking active
Measuring-point ID 2
Rated primary current 6000 A
Rated secondary current 5A
Current range 100 x IR
Internal CT type CT protection
Neutr.point in dir.of ref.obj yes
Inverted phases none
CT 1
Magnitude correction 1 0.01 - 10 0.001
Phase IA
CT 2
Magnitude correction 1 0.01 - 10 0.001
Phase IB
CT 3
Magnitude correction 1 0.01 - 10 0.001
Phase IC
CT 4
Magnitude correction 1 0.01 - 10 0.001
Phase IN
Brk.wire det.
Supv. balan. I
Mode on
Release threshold 3000 A 180 - 210000 1
Threshold min/max 0.5 0.1 - 0.95 0.01
Delay failure indication 5 s 0 - 100 0.01
Supv. ph.seq.I
Mode on
Delay failure indication 5 s 0 - 100 0.01
Supv. sum I
Mode on
Threshold 600 A 180 - 60000 1
Unrestricted
Function group Function Function block Setting name Settings group1 Unit Min - Max Step
Slope factor 0.1 0 - 0.95 0.01
Delay failure indication 5 s 0 - 100 0.01
Supv.ADC sum I
Mode off
20TA
CT 3-phase
CT connection 3-phase + IN
Tracking active
Measuring-point ID 5
Rated primary current 6000 A
Rated secondary current 5A
Current range 100 x IR
Internal CT type CT protection
Neutr.point in dir.of ref.obj yes
Inverted phases none
CT 1
Magnitude correction 1 0.01 - 10 0.001
Phase IA
CT 2
Magnitude correction 1 0.01 - 10 0.001
Phase IB
CT 3
Magnitude correction 1 0.01 - 10 0.001
Phase IC
CT 4
Magnitude correction 1 0.01 - 10 0.001
Phase IN
Brk.wire det.
Supv. balan. I
Mode on
Release threshold 3000 A 180 - 210000 1
Threshold min/max 0.5 0.1 - 0.95 0.01
Delay failure indication 5 s 0 - 100 0.01
Supv. ph.seq.I
Mode on
Delay failure indication 5 s 0 - 100 0.01
Supv. sum I
Mode on
Threshold 600 A 180 - 60000 1
Slope factor 0.1 0 - 0.95 0.01
Delay failure indication 5 s 0 - 100 0.01
Supv.ADC sum I
Mode on
Recording
Fault recording with pickup
Storage always
Maximum record time 5 s 0.2 - 80 0.01
Pre-trigger time 0.5 s 0.05 - 16 0.01
Post-trigger time 0.5 s 0.05 - 16 0.01
Manual record time 0.5 s 0.2 - 80 0.01
Sampling frequency 2 kHz
Sampl. freq. IEC61850 rec. 1 kHz
Scaling COMTRADE Secondary values
GCB
General
Rated normal current 6000 A
Rated voltage 10500 V
Current thresh. CB open 99 A 45 - 15000 1
Trip logic
Reset of trip command with I<
Circuit break.
Output time 0.1 s 0.02 - 1800 0.01
Indicat. of breaking values always
Manual close
Action time 0.3 s 0.01 - 60 0.01
CB open dropout delay 0 s 0 - 60 0.01
Reset LED Group
Control
Control model SBO w. enh. security
SBO time-out 30 s 0.01 - 1800 0.01
Feedback monitoring time 1 s 0.01 - 1800 0.01
Check switching authority yes
Check if pos. is reached yes
Check double activat. blk. yes
Check blk. by protection yes
Interlocking
CB test
Dead time 0.1 s 0 - 60 0.01
Trip only false
Consider current criterion false
74TC sup.1BI 1
Mode on
Unrestricted
Function group Function Function block Setting name Settings group1 Unit Min - Max Step
Alarm delay 300 s 1 - 600 0.01
50BF CB fail.1
Mode on
Holding int. start signal yes
Start via binary input no
Holding ext. start signal no
w. 'CB pos. closed
CB aux.cont. crit. allowed
3p.'
with effective
Dropout
criterion
Retrip after T1 start T2 after T1
Threshold phase current 2500 A 45 - 52500 1
Threshold sensitive 2500 A 45 - 52500 1
Delay T1 for 3-pole retrip 0.05 s 0 - 60 0.001
Delay T2 for 3-pole trip 0.13 s 0.05 - 60 0.001
Minimum operate time 0.1 s 0 - 60 0.01
3I0 criterion Plausibility check
I2 criterion Plausibility check
Threshold 3I0 dir. release 225 A 45 - 52500 1
Threshold I2 dir. release 225 A 45 - 52500 1
Monit. time for BI ">Start" 15 s 0.05 - 60 0.01
Transformer diff. 1
87T diff. prot. 1
General
CT mismatch side 1 M3ph 1 1.95134473
CT mismatch side 2 M3ph 1 2.453119
CT mismatch side 2 M3ph 2 2.453119
Reference side is Side 2
MU-ID Side 1 Mp3ph 1 1
MU-ID Side 2 Mp3ph 1 2
MU-ID Side 2 Mp3ph 2 5
I-DIFF
Mode on
Operate & flt.rec. blocked no
Operate delay 0 s 0 - 60 0.01
Threshold 0.2 I/IrObj 0.05 - 2 0.01
Slope 1 0.3 0 - 0.8 0.01
Intersection 1 Irest 0.67 I/IrObj 0 - 5 0.01
Slope 2 0.7 0.25 - 0.95 0.01
Intersection 2 Irest 2.5 I/IrObj 1 - 20 0.01
Starting detection no
Thresh. startup detection 0.1 I/IrObj 0.1 - 2 0.1
Factor increasing char. 2 1 - 5 0.1
Max. perm. Start. time 5 s 0.1 - 180 0.1
Factor increasing char. DC 2.3 1 - 5 0.1
Blocking with 2. harmonic yes
2nd harmonic content 15.00% 10.00% - 45.00% 1.00%
Crossblock. time 2nd har. 0.1 s 0 - 200 0.01
Blocking with CWA no
Blocking with 3rd harm. no
3rd harmonics content 30.00% 10.00% - 80.00% 1.00%
Crossblock. time 3rd har. 0 s 0 - 200 0.01
Blocking with 5th harm. no
5th harmonics content 30.00% 10.00% - 80.00% 1.00%
Crossblock. time 5th har. 0 s 0 - 200 0.01
Limit Idiff 3., 5. harmonics 1.5 I/IrObj 0.5 - 20 0.1
Threshold add-on stabiliz. 2 I/IrObj 1 - 20 0.01
Time of add-on stabiliz. 0.3 s 0 - 5 0.01
Crossblk. time add-on st. 0.3 s 0 - 2 0.01
I-DIFF fast
Mode on
Threshold 5.5 I/IrObj 0.5 - 35 0.1
Operate delay 0 s 0 - 60 0.01
Operate & flt.rec. blocked no
Group indicat.
Transformer side 1
General
Rated apparent power 75000000 VA
Rated voltage 35000 V
Rated current 1237.2154404487 A
Neutral point grounded
Winding configuration Y (Wye)
Vector group numeral 0
Side number Side 1
MI3ph1 usesMeasP with ID 1
CT mismatch M I-3ph 1 1.95134473
Transformer side 2
General
Rated apparent power 75000000 VA
Rated voltage 10500 V
Rated current 4124.05146816232 A
Neutral point grounded
Winding configuration D (Delta)
Vector group numeral 11
Unrestricted
Function group Function Function block Setting name Settings group1 Unit Min - Max Step
Side number Side 2
MI3ph1 usesMeasP with ID 2
MI3ph2 usesMeasP with ID 5
CT mismatch M I-3ph 1 2.453119
CT mismatch M I-3ph 2 2.453119
Unrestricted
Name of imported TEA-X file: Transformer CFG_7SJ85.teax
File creation time: 09-10-2018 10:10:50 AM
Name: 7SJ85
IEC 61850 name: H01R01_7SJ
Type: 7SJ85
Product code: 7SJ85-DAAA-AA0-0AAAA0-AF0111-12111B-AAA000-000AC0-CB1BA1-CF0
Short product code (TNS): P1J288495
Project name: 77OP-V-100170_V14
Function group Function Function block Setting name Settings group1 Unit Min - Max Step
General
Rated frequency 50 Hz
Minimum operate time 0 s 0 - 60 0.01
Set. format residu. comp. Kr; Kx
Block monitoring dir. off
Reserv.time for com.prot. 120 s 0 - 65535 1
No. permis.state changes 0 0 - 65535 1
Initial test time 1 s 1 - 65535 1
No. of chatter tests 0 -1 - 32767 1
Chatter idle time 1 min 1 - 65535 1
Subsequent test time 2 s 2 - 65535 1
Number settings groups 1
Activat. of settings group settings group 1
Blk setting change false
Energy restore interval 10 min 0 - 60 1
Energy restore time none
Energy restore latest value
Energy restore by A.time false
Enable sw.auth. station false
Multiple sw.auth. levels false
Specific sw. authorities false
Fault-display with pickup
CFC chart quality handling automatic
Activate device test mode false
Oper.bin.outp. under test false
Time managem.
Date format DD.MM.YYYY
Time zone offset to UTC 60 min -720 - 840 15
Offset daylight sav. time 60 min 0 - 120 15
Switch daylight sav. time true
Last/Sunday/March/0
Start of daylight sav. time 2:00
Last/Sunday/October/
End of daylight sav. time 03:00
Time sync.
Fault indication after 600 s 0 - 3600 1
Time source 1 none
Time source 1 port NotUsed
Time source 1 channel NotUsed
Time source 2 none
Time source 2 port NotUsed
Time source 2 channel NotUsed
Time zone time source 1 local
Time zone time source 2 local
Sync. latency time src.1 0 s 0 - 1 1E-08
Sync. latency time src.2 0 s 0 - 1 1E-08
Power system
General
Phase sequence ABC
4TA
CT 3-phase
CT connection 3-phase + IN
Tracking active
Measuring-point ID 1
Rated primary current 6000 A
Rated secondary current 5A
Current range 100 x IR
Internal CT type CT protection
Neutr.point in dir.of ref.obj yes
Inverted phases none
CT 1
Magnitude correction 1 0.01 - 10 0.001
Phase IA
CT 2
Magnitude correction 1 0.01 - 10 0.001
Phase IB
CT 3
Magnitude correction 1 0.01 - 10 0.001
Phase IC
CT 4
Magnitude correction 1 0.01 - 10 0.001
Phase IN
Brk.wire det.
Mode off
Supv. balan. I
Mode off
Release threshold 3000 A 180 - 210000 1
Threshold min/max 0.5 0.1 - 0.95 0.01
Delay failure indication 5 s 0 - 100 0.01
Supv. ph.seq.I
Mode off
Delay failure indication 5 s 0 - 100 0.01
Supv. sum I
Mode off
Threshold 600 A 180 - 60000 1
Slope factor 0.1 0 - 0.95 0.01
Delay failure indication 5 s 0 - 100 0.01
Supv.ADC sum I
Mode off
PT1
VT 3-phase
Unrestricted
Function group Function Function block Setting name Settings group1 Unit Min - Max Step
Rated primary voltage 35000 V
Rated secondary voltage 110 V
Matching ratio Vph / VN 1.73
3 ph-to-gnd volt. +
VT connection VN
Inverted phases none
Tracking active
Measuring-point ID 2
VT 1
Magnitude correction 1 0.01 - 10 0.001
Phase VA
VT 2
Magnitude correction 1 0.01 - 10 0.001
Phase VB
VT 3
Magnitude correction 1 0.01 - 10 0.001
Phase VC
VT 4
Magnitude correction 1 0.01 - 10 0.001
Phase VN
Supv. balan. V
Mode off
Release threshold 17500 V 95 - 59500 1
Threshold min/max 0.75 0.58 - 0.95 0.01
Delay failure indication 5 s 0 - 100 0.01
Supv. ph.seq.V
Mode off
Delay failure indication 5 s 0 - 100 0.01
Supv. sum V
Mode off
Threshold 8750 V 95 - 59500 1
Delay failure indication 5 s 0 - 100 0.01
VT miniatureCB
Response time 0 s 0 - 0.03 0.01
Recording
Fault recording with pickup
Storage always
Maximum record time 5 s 0.2 - 80 0.01
Pre-trigger time 0.5 s 0.05 - 16 0.01
Post-trigger time 0.5 s 0.05 - 16 0.01
Manual record time 0.5 s 0.2 - 80 0.01
Sampling frequency 2 kHz
Sampl. freq. IEC61850 rec. 1 kHz
Scaling COMTRADE Secondary values
VI 3ph 1
General
Rated current 1500 A
Rated voltage 35000 V
Rated apparent power 75000000 VA
Power-sys. neutral point grounded
P, Q sign not reversed
50/51 OC-3ph-B1
Group indicat.
Definite-T 1
Mode off
Operate & flt.rec. blocked no
Method of measurement fundamental comp.
Threshold 1706 A 180 - 210000 1
Operate delay 0 s 0 - 60 0.01
Inverse-T 1
Mode on
Operate & flt.rec. blocked no
Method of measurement fundamental comp.
Threshold 1500 A 180 - 210000 1
Type of character. curve IEC normal inverse
Reset instantaneous
Time dial 0.5 0.05 - 15 0.01
50N/51N OC-gnd-B1
Group indicat.
Definite-T 1
Mode off
Operate & flt.rec. blocked no
Method of measurement fundamental comp.
Threshold 1706 A 60 - 210000 1
Operate delay 0 s 0 - 60 0.01
Inverse-T 1
Mode off
Operate & flt.rec. blocked no
Method of measurement fundamental comp.
Threshold 1500 A 60 - 210000 1
IEC normal inverse
Type of character. curve
Reset instantaneous
Time dial 0.5 0.05 - 15 0.01
Energy
General
Energy
67 Dir.OC-3ph-B1
General
Rotation angle of ref. volt. 45 ° -180 - 180 1
Group indicat.
Definite-T 1
Mode on
Operate & flt.rec. blocked no
Directional mode forward
Method of measurement fundamental comp.
Blk. by meas.-volt. failure yes
Threshold 1706 A 180 - 210000 1
Operate delay 0.5 s 0 - 60 0.01
Unrestricted
Function group Function Function block Setting name Settings group1 Unit Min - Max Step
Inverse-T 1
Mode off
Operate & flt.rec. blocked no
Directional mode forward
Method of measurement fundamental comp.
Blk. by meas.-volt. failure yes
Threshold 1200.000072 A 180 - 210000 1
Type of character. curve IEC normal inverse
Reset instantaneous
Time dial 0.3 0.05 - 15 0.01
59 Overvolt.-3ph 1
Group indicat.
Definite-T 1
Mode on
Operate & flt.rec. blocked no
Measured value phase-to-phase
Method of measurement fundamental comp.
Pickup mode 1 out of 3
Threshold 45500 V 95 - 108182 1
Dropout ratio 0.95 0.9 - 0.99 0.01
Operate delay 0.5 s 0 - 300 0.01
49
Definite-T 1
Mode on
Operate & flt.rec. blocked no
1-pole operate allowed no
Dynamic settings no
Method of measurement fundamental comp.
Threshold 1313 A 180 - 210000 1
Dropout ratio 0.95 0.9 - 0.99 0.01
Pickup delay 0 s 0 - 60 0.01
Dropout delay 0 s 0 - 60 0.01
Operate delay 15 s 0 - 60 0.01
67N Dir.OC-gnd-A1
General
Measured value IN measured
Min. voltage V0 or V2 2100 V 48 - 7000 1
Rotation angle of ref. volt. -45 ° -180 - 180 1
Forward section +/- 88 ° 0 - 90 1
Polarization with negative sequence
Group indicat.
Definite-T 1
Mode on
Operate & flt.rec. blocked no
Directional mode forward
Method of measurement fundamental comp.
Directional comparison no
Release via input signal no
Blk. by meas.-volt. failure yes
Dynamic settings no
Threshold 1706 A 60 - 210000 1
Dropout ratio 0.95 0.9 - 0.99 0.01
Dropout delay 0 s 0 - 60 0.01
Operate delay 0.5 s 0 - 60 0.01
Definite-T 2
Mode on
Operate & flt.rec. blocked no
Directional mode forward
Method of measurement fundamental comp.
Directional comparison no
Release via input signal no
Blk. by meas.-volt. failure yes
Dynamic settings no
Threshold 1500 A 180 - 210000 1
Dropout ratio 0.95 0.9 - 0.99 0.01
Dropout delay 0 s 0 - 60 0.01
Operate delay 0.8 s 0 - 60 0.01
Inverse-T 1
Mode off
Operate & flt.rec. blocked no
Directional mode forward
Method of measurement fundamental comp.
Directional comparison no
Release via input signal no
Blk. by meas.-volt. failure yes
Dynamic settings no
Threshold 1200 A 180 - 210000 1
Type of character. curve IEC normal inverse
Unrestricted
Function group Function Function block Setting name Settings group1 Unit Min - Max Step
Min. time of the curve 0 s 0 - 1 0.01
Reset disk emulation
Time dial 1 0 - 15 0.01
Additional time delay 0 s 0 - 60 0.01
51V OC-3ph V-dep.1
Group indicat.
V-dependent 1
Mode on
Operate & flt.rec. blocked no
Method of measurement fundamental comp.
Threshold 1422 A 180 - 210000 1
IEC normal inverse
Type of character. curve
Reset disk emulation
Time dial 1 0.05 - 15 0.01
V-seal-in 1
Mode on
Operate & flt.rec. blocked no
Threshold 1422 A 180 - 210000 1
Operate delay 3 s 0 - 60 0.01
Blk. by meas.-volt. failure yes
State of V-seal-in off
V-seal-in threshold 21000 V 95 - 61250 1
Duration of V-seal-in time 4 s 0.1 - 60 0.01
Disconnector 1
Control
SBO w. enh. security
Control model
SBO time-out 30 s 0.01 - 1800 0.01
Feedback monitoring time 10 s 0.01 - 1800 0.01
Check switching authority yes
Check if pos. is reached yes
Check double activat. blk. yes
Interlocking
Disconnector
Maximum output time 10 s 0.02 - 1800 0.01
Seal-in time 0 s 0 - 60 0.01
Switching-device type disconnector
Disconnector 2
Control
SBO w. enh. security
Control model
SBO time-out 30 s 0.01 - 1800 0.01
Feedback monitoring time 10 s 0.01 - 1800 0.01
Check switching authority yes
Check if pos. is reached yes
Check double activat. blk. yes
Interlocking
Disconnector
Maximum output time 10 s 0.02 - 1800 0.01
Seal-in time 0 s 0 - 60 0.01
Switching-device type disconnector
Disconnector 3
Control
SBO w. enh. security
Control model
SBO time-out 30 s 0.01 - 1800 0.01
Feedback monitoring time 10 s 0.01 - 1800 0.01
Check switching authority yes
Check if pos. is reached yes
Check double activat. blk. yes
Interlocking
Disconnector
Maximum output time 10 s 0.02 - 1800 0.01
Seal-in time 0 s 0 - 60 0.01
Switching-device type disconnector
GCB 35kV断路器
General
Rated normal current 1500 A
Rated voltage 35000 V
Current thresh. CB open 2500 A 180 - 60000 1
Trip logic
Reset of trip command with I<
Circuit break.
Output time 0.1 s 0.02 - 1800 0.01
Indicat. of breaking values always
Manual close
Action time 0.3 s 0.01 - 60 0.01
CB open dropout delay 0 s 0 - 60 0.01
Reset LED Group
Control
SBO w. enh. security
Control model
SBO time-out 30 s 0.01 - 1800 0.01
Feedback monitoring time 1 s 0.01 - 1800 0.01
Check switching authority yes
Check if pos. is reached yes
Check double activat. blk. yes
Check blk. by protection yes
Interlocking
CB test
Dead time 0.1 s 0 - 60 0.01
Trip only false
Consider current criterion false
Unrestricted
MBA #1
50 Hz
0.15
Kr; Kx
off
120
0
1
0
1
2
1
settings group 1
false
10
none
latest value
x
x
x
x
x
automatic
true
true
x
x
x
x
x
600
SNTP
port E
x
IRIG-B
port G
x
UTC
UTC
x
x
ABC
3-phase + IN
active
1
6000
5A
100 x IR
CT protection
no
none
1
IA
1
IB
1
IC
1
IN
off
off
3000
0.5
5
off
5
off
600
0.1
5
off
Unrestricted
MBA #1
35000
110
1.73
3 ph-to-gnd volt. +
VN
none
active
2
1
VA
1
VB
1
VC
1
VN
off
17500
0.75
5
off
5
off
8750
5
with pickup
always
5
0.5
0.5
0.5
2 kHz
1 kHz
Secondary values
1500
35000
90930000
grounded
not reversed
off
no
fundamental comp.
1706
0
on
no
fundamental comp.
1500
IEC normal inverse
instantaneous
0.5
off
no
fundamental comp.
1706
0
off
no
fundamental comp.
1500
IEC normal inverse
instantaneous
0.5
45
on
no
forward
fundamental comp.
yes
1706
0.5
Unrestricted
MBA #1
x
x
x
x
x
x
x
x
x
on
no
phase-to-phase
fundamental comp.
1 out of 3
45500
0.95
0.5
on
no
no
no
fundamental comp.
1313
0.95
0
0
15
IN measured
2100
-45
88
negative sequence
on
no
forward
fundamental comp.
no
no
yes
no
1706
0.95
0
0.5
on
no
forward
fundamental comp.
no
no
yes
no
1500
0.95
0
0.8
x
x
x
x
x
x
x
x
x
x
Unrestricted
MBA #1
x
x
x
x
on
no
fundamental comp.
1422
IEC normal inverse
instantaneous
1
on
no
1422
3
yes
off
12091
4
SBO w. enh.
security
30
10
x
x
x
10
0
x
SBO w. enh.
security
30
10
x
x
x
10
0
x
SBO w. enh.
security
30
10
x
x
x
10
0
x
1500
35000
2500
with I<
0.1
always
0.3
0
SBO w. enh.
security
30
1
x
x
x
x
0.1
false
false
Unrestricted
TEA-X file name: Siprotec_F511-7UM85.teax
File creation time: 16-06-2019 09:29:35 PM
Device name: F511-7UM85
IEC 61850 name: K01R01_F511
Device type: 7UM85
Product code: 7UM85-DAAA-AA0-0AAAA0-AP0111-12111B-AAA000-000AC0-CH2BA1-CK1
Short product code (TNS): P1L85393
Project name: 77OP-V-100170_V14
Editable cells
Function group Function Function block Settings category Setting name Settings group1 Unit Min - Max Step
General
Device Rated frequency 50 Hz
Minimum operate time 0.15 s 0 - 60 0.01
Set. format residu. comp. Kr; Kx
Block monitoring dir. off
Station name 77OP-V-100170
Chatter blocking No. permis.state changes 0 0 - 65535 1
Initial test time 1 s 1 - 65535 1
No. of chatter tests 0 -1 - 32767 1
Chatter idle time 1 min 1 - 65535 1
Subsequent test time 2 s 2 - 65535 1
Number settings groups 1
Activat. of settings group settings group 1
Blk setting change false
Reserv.time for com.prot. 120 s 0 - 65535 1
Control Enable sw.auth. station false
Multiple sw.auth. levels false
Specific sw. authorities false
Spontan.indic. Fault-display with pickup
CFC CFC chart quality handling automatic
Test support Activate device test mode false
Oper.bin.outp. under test false
Time managem.
General Date format DD.MM.YYYY
Time zone and daylight saving time Time zone offset to UTC 60 min -720 - 840 15
Offset daylight sav. time 60 min 0 - 120 15
Switch daylight sav. time true
Last/Sunday/March/
Start of daylight sav. time
02:00
Last/Sunday/October
End of daylight sav. time
/03:00
Time sync.
Time source Fault indication after 600 s 0 - 3600 1
Time source 1 SNTP
Time source 1 port port E
Time source 1 channel Ch1
Time source 2 IRIG-B
Time source 2 port port G
Time source 2 channel NotUsed
Time zone time source 1 UTC
Time zone time source 2 UTC
Sync. latency time src.1 0.00 µs 0 - 1000000 0.01
Sync. latency time src.2 0.00 µs 0 - 1000000 0.01
Localization
Unit system SI
Power system
General
Phase sequence ABC
12TA
CT 3-phase
3-phase + IN-
General CT connection
separate
Tracking active
Measuring-point ID 1
CT phases Rated primary current 6000.0 A
Rated secondary current 5A
Current range 100 x IR
Internal CT type CT protection
Neutr.point in dir.of ref.obj yes
Inverted phases none
CT IN Rated primary current 6000.0 A
Rated secondary current 5A
Current range 100 x IR
Internal CT type CT protection
CT 1
Magnitude correction 1.000 0.01 - 10 0.001
Phase IA
Function group Function Function block Settings category Setting name Settings group1 Unit Min - Max Step
CT 2
Magnitude correction 1.000 0.01 - 10 0.001
Phase IB
CT 3
Magnitude correction 1.000 0.01 - 10 0.001
Phase IC
CT 4
Magnitude correction 1.000 0.01 - 10 0.001
Phase IN
Supv. balan. I
Mode off
Release threshold 3000 A 180 - 210000 1
Threshold min/max 0.50 0.1 - 0.95 0.01
Delay failure indication 5.00 s 0 - 100 0.01
Supv. ph.seq.I
Mode off
Delay failure indication 5.00 s 0 - 100 0.01
Supv. sum I
Mode off
Threshold 600 A 180 - 60000 1
Slope factor 0.10 0 - 0.95 0.01
Delay failure indication 5.00 s 0 - 100 0.01
14TA
General
Rated primary current 40.0 A
Rated secondary current 5A
Current range 1.6 x IR
Internal CT type CT measurement
Term. 1,3,5,7 in dir. of obj. yes
Tracking inactive
Measuring-point ID 2
CT 1
Magnitude correction 1.000 0.01 - 10 0.001
Phase Ix
U4
VT 3-phase
Rated primary voltage 10.500 kV
Rated secondary voltage 110 V
Matching ratio Vph / VN 1.73
3 ph-to-gnd volt. +
VT connection
VN
Inverted phases none
Tracking active
Measuring-point ID 3
VT 1
Magnitude correction 1.000 0.01 - 10 0.001
Phase VA
VT 2
Magnitude correction 1.000 0.01 - 10 0.001
Phase VB
VT 3
Magnitude correction 1.000 0.01 - 10 0.001
Phase VC
VT 4
Magnitude correction 1.000 0.01 - 10 0.001
Phase VN
Supv. balan. V
Mode on
Release threshold 5.250 kV 0.029 - 17.85 0.001
Threshold min/max 0.75 0.58 - 0.95 0.01
Delay failure indication 5.00 s 0 - 100 0.01
Supv. ph.seq.V
Mode on
Delay failure indication 5.00 s 0 - 100 0.01
Supv. sum V
Mode on
Threshold 2.625 kV 0.029 - 17.85 0.001
Delay failure indication 5.00 s 0 - 100 0.01
VT miniatureCB
Response time 0.00 s 0 - 0.03 0.01
UE
General
Rated primary voltage 10.500 kV
Rated secondary voltage 110 V
Tracking inactive
Measuring-point ID 6
VT 1
Function group Function Function block Settings category Setting name Settings group1 Unit Min - Max Step
Magnitude correction 1.000 0.01 - 10 0.001
Phase Vx
VT miniatureCB
Response time 0.00 s 0 - 0.03 0.01
u0
General
Rated primary voltage 10.500 kV
Rated secondary voltage 110 V
Tracking inactive
Measuring-point ID 4
VT 1
Magnitude correction 1.000 0.01 - 10 0.001
Phase Vx
VT miniatureCB
Response time 0.00 s 0 - 0.03 0.01
Recording
Fault recorder
Control
Fault recording with pickup
Storage always
Maximum record time 5.00 s 0.2 - 80 0.01
Pre-trigger time 0.50 s 0.05 - 16 0.01
Post-trigger time 0.50 s 0.05 - 16 0.01
Manual record time 0.50 s 0.2 - 80 0.01
Sampling frequency 2 kHz
Sampl. freq. IEC61850 rec. 1 kHz
COMTRADE revision year COMTRADE 1999
Scaling COMTRADE Secondary values
Cal.zero.seq.cur.channel no
Cal.zero seq.volt.channel no
Security
DIGSI access
MMS access
Module Port E read/write
Web access
Security Logging
Sec. Ev. Logg.
General Security log cap. warn. 80 % 0 - 100 5
Syslog server A Enable logging false
Syslog server B Enable logging false
Access control
Login attempts
Max. login attempts 5 5 - 12 1
Time lapse 5 min 1 - 30 1
Blocked duration 30 min 30 - 360 1
User cache
User cache size 60 0 - 100 1
Analog units
MT fast 1
MT in 1
TD input-signal type Voltage input
Unit V
Measuring window 10 ms
Range active false
Conversion factor 1.00
MT in 2
TD input-signal type Voltage input
Unit V
Measuring window 10 ms
Range active false
Conversion factor 1.00
MT in 3
TD input-signal type Voltage input
Unit V
Measuring window 10 ms
Range active false
Conversion factor 1.00
MT in 4
TD input-signal type Voltage input
Function group Function Function block Settings category Setting name Settings group1 Unit Min - Max Step
Unit V
Measuring window 10 ms
Range active false
Conversion factor 1.00
Generator stator
General
General
Rated values Rated apparent power 75.00 MVA
Rated voltage 10.50 kV
Rated current 4124 A
SGF3Har. conf. V SGF connected to neutr. transf.
Further settings
Measurements P, Q sign not reversed
Add.Meas.Value
Synchronous reactance 208.6 % 30 - 300 0.1
27 Undervolt.-3ph 1
General
Current-flow criterion on
Threshold I> 180.0000108 A 180 - 60000 1
Definite-T 1
Mode off
Operate & flt.rec. blocked no
Blk. by meas.-volt. failure yes
Measured value phase-to-phase
Method of measurement fundamental comp.
Pickup mode 1 out of 3
Pickup delay no
Threshold 8.400 kV 0.029 - 18.375 0.001
Dropout ratio 1.05 1.01 - 1.2 0.01
Operate delay 3.00 s 0 - 60 0.01
59 Overvolt.-3ph 1
Definite-T 1
Mode on
Operate & flt.rec. blocked no
Measured value phase-to-phase
Method of measurement fundamental comp.
Pickup mode 1 out of 3
Threshold 13.650 kV 0.029 - 32.455 0.001
Dropout ratio 0.95 0.9 - 0.99 0.01
Operate delay 0.50 s 0 - 300 0.01
40 Underexc. prot. 1
General
Threshold V1 min 1.650 kV 0.029 - 19.091 0.001
Blk. by meas.-volt. failure yes
Characteristic
Mode on
Operate & flt.rec. blocked no
1/xd characteristic 1 0.53 0.1 - 5 0.01
Angle characteristic 1 75.8 ° 50 - 120 1
Operate delay char. 1 3.00 s 0 - 60 0.01
1/xd characteristic 2 0.43 0.1 - 5 0.01
Angle characteristic 2 84.3 ° 50 - 120 1
Operate delay char. 2 3.00 s 0 - 60 0.01
1/xd characteristic 3 0.96 0.1 - 5 0.01
Angle characteristic 3 100 ° 50 - 120 1
Operate delay char. 3 0.30 s 0 - 60 0.01
46 I2 1
General
Reference value rated current
Current limitation Imax no
Release current 180.0000108 A 180 - 60000 0
Definite-T 1
Mode on
Operate & flt.rec. blocked no
Threshold 0.1 5.00% - 999.90% 0.10%
Dropout ratio 0.95 0.4 - 0.99 0.01
Dropout delay 0.00 s 0 - 60 0.01
Operate delay 1.50 s 0 - 60 0.01
50/51 OC-3ph-B1
Definite-T 1
Mode off
Operate & flt.rec. blocked no
Method of measurement fundamental comp.
Threshold 1200.000072 A 180 - 210000 1
Operate delay 0.30 s 0 - 100 0.01
Inverse-T 1
Function group Function Function block Settings category Setting name Settings group1 Unit Min - Max Step
Mode off
Operate & flt.rec. blocked no
Method of measurement fundamental comp.
Threshold 1200.000072 A 180 - 210000 1
Type of character. curve IEC normal inverse
Reset instantaneous
Time dial 0.30 0.05 - 15 0.01
49
49
General Mode off
Operate & flt.rec. blocked no
Curve based on preload 100 % 0 - 100 1
Threshold current warning 2448.00014688 A 180 - 210000 1
Threshold thermal warn. 90.00% 50.00% - 100.00% 1.00%
Dropout threshold operate 90.00% 50.00% - 99.00% 1.00%
Emerg. start T overtravel 300 s 0 - 15000 10
Imin cooling 4800.00028800001 A 0 - 60000 1
Cool-down factor Tau 7.0 0.5 - 20 0.1
Storage of thermal replica yes
Imax thermal 6114.664 A 180 - 60000 1
Behav. at I> Imax therm. current limiting
10;30;1.2;10;1.3;20;
1.4;30;1.5;40;1.6;50;
1.7;60;1.8;70;1.9;80;
1.1;90;1.11;100;1.12
;110;1.13;120;1.14;1
30;1.15;140;1.16;150
Operate curve Operate char. curve ;1.17;160;1.18;170;1
.19;180;1.2;190;1.21
;200;1.1;600;1.1;600
;1.1;600;1.1;600;1.1;
600;1.1;600;1.1;600;
1.1;600;1.1;600;1.1;
600;
24 Overexcitation 1
Definite-T 1
Mode off
Operate & flt.rec. blocked no
Threshold 1.40 1 - 1.4 0.01
Operate delay 1.00 s 0 - 60 0.01
Therm.charact.
Therm.charact. Mode on
Operate & flt.rec. blocked no
Threshold 1.10 1 - 1.2 0.01
Warning delay 2.00 s 0 - 60 0.01
Cooling time therm.replica 3600 s 0 - 100000 1
8;30;1.05;20000;1.1;
6000;1.15;240;1.2;60
;1.25;30;1.3;19;1.35;
13;1.4;10;1.45;10;1.
5;10;1.55;10;1.6;10;
1.65;10;1.7;10;1.75;
Operate curve Operate char. curve
10;1.8;10;1.85;10;1.
9;10;1.95;10;2;10;2.
05;10;2.1;10;2.15;10
;2.2;10;2.25;10;2.3;1
0;2.35;10;2.4;10;2.4
5;10;2.5;10;
81 Overfreq.-B 1
General
Minimum voltage 6.825 kV 0.286 - 18.375 0.001
Dropout differential 0.02 Hz 0.02 - 2 0.01
Stage 1
Mode on
Operate & flt.rec. blocked no
Threshold 51.50 Hz 40 - 70 0.01
Operate delay 10.00 s 0 - 600 0.01
Stage 2
Mode off
Operate & flt.rec. blocked no
Threshold 64.80 Hz 40 - 70 0.01
Operate delay 5.00 s 0 - 600 0.01
81 Underfreq.-B 1
General
Minimum voltage 6.825 kV 0.286 - 18.375 0.001
Dropout differential 0.02 Hz 0.02 - 2 0.01
Stage 1
Function group Function Function block Settings category Setting name Settings group1 Unit Min - Max Step
Mode on
Operate & flt.rec. blocked no
Threshold 49.80 Hz 40 - 70 0.01
Operate delay 10.00 s 0 - 600 0.01
Stage 2
Mode off
Operate & flt.rec. blocked no
Threshold 57.00 Hz 40 - 70 0.01
Operate delay 10.00 s 0 - 600 0.01
Stage 3
Mode off
Operate & flt.rec. blocked no
Threshold 56.40 Hz 40 - 70 0.01
Operate delay 10.00 s 0 - 600 0.01
78 Out-of-step 1
General
I1<threshold blocks zone 20 % 10 - 400 1
I2>threshold blocks zone 20 % 5 - 500 1
Zone 1
Mode on
Operate & flt.rec. blocked no
Zone limit R 1.990 Ω 0.001 - 10.5 0.001
Zone limit X top 1.940 Ω -10.5 - 10.5 0.001
Zone limit X bottom 4.950 Ω -10.5 - 10.5 0.001
Rotation angle 90.0 ° 60 - 90 0.1
Count at exit
Number of power swings 1 1 - 20 1
Re-entry time 20.00 s 0 - 60 0.01
Signal time 0.05 s 0 - 60 0.01
51V OC-3ph V-dep.1
V-dependent 1
Mode on
Operate & flt.rec. blocked no
Method of measurement fundamental comp.
Threshold 6420.00038520002 A 180 - 210000 1
Type of character. curve IEC normal inverse
Reset disk emulation
Time dial 1.00 0.05 - 15 0.01
V-seal-in 1
Mode off
Operate & flt.rec. blocked no
Threshold 6420.00038520002 A 180 - 210000 1
Operate delay 3.00 s 0 - 60 0.01
Blk. by meas.-volt. failure yes
State of V-seal-in off
V-seal-in threshold 6.300 kV 0.029 - 18.375 0.001
Duration of V-seal-in time 4.00 s 0.1 - 60 0.01
32R Revers.pow. 1
General
Angle correction 0.00 ° -10 - 10 0.01
Minimum voltage V1 0.525 kV 0.029 - 6.3 0.001
Stage 1
Mode on
Operate & flt.rec. blocked no
Threshold -0.01 -30.00% - -0.30% 0.01%
Dropout ratio 0.60 0.4 - 0.99 0.01
Dropout delay 0.00 s 0 - 60 0.01
Operate delay 10.00 s 0 - 60 0.01
Operate delay stop valve 1.00 s 0 - 60 0.01
Stage 2
Mode off
Operate & flt.rec. blocked no
Threshold -0.01 -30.00% - -0.30% 0.01%
Dropout ratio 0.60 0.4 - 0.99 0.01
Dropout delay 0.00 s 0 - 60 0.01
Operate delay 10.00 s 0 - 60 0.01
Operate delay stop valve 1.00 s 0 - 60 0.01
67 Dir.OC-3ph-B1
General
Rotation angle of ref. volt. 45 ° -180 - 180 1
Definite-T 1
Mode on
Operate & flt.rec. blocked no
Directional mode forward
Method of measurement fundamental comp.
Blk. by meas.-volt. failure yes
Function group Function Function block Settings category Setting name Settings group1 Unit Min - Max Step
Threshold 4948.717 A 180 - 210000 1
Operate delay 0.30 s 0 - 60 0.01
Definite-T 2
Mode off
Operate & flt.rec. blocked no
Directional mode forward
Method of measurement fundamental comp.
Blk. by meas.-volt. failure yes
Threshold 6598.289 A 180 - 210000 1
Operate delay 0.10 s 0 - 60 0.01
Inverse-T 1
Mode on
Operate & flt.rec. blocked no
Directional mode forward
Method of measurement fundamental comp.
Blk. by meas.-volt. failure yes
Threshold 4948.717 A 180 - 210000 1
Type of character. curve IEC normal inverse
Reset disk emulation
Time dial 1.00 0.05 - 15 0.01
SGF 90% MP-1ph 1
General
Dropout delay 1.00 s 0 - 60 0.01
Core balance CT- current 1 2.000 A 0.04 - 64 0.001
Core balance CT- current 2 40.000 A 0.04 - 64 0.001
CT angle error at I1 0.0 ° 0 - 5 0.1
CT angle error at I2 0.0 ° 0 - 5 0.1
V0> 1
Mode on
Operate & flt.rec. blocked no
Method of measurement fundamental comp.
Threshold 3.15 kV 1.2 - 800 0.01
Dropout ratio 0.95 0.9 - 0.99 0.01
Pickup delay 0.00 s 0 - 60 0.01
Operate delay 0.30 s 0 - 60 0.01
3I0> φ(VI) 1
Mode on
Operate & flt.rec. blocked no
Directional mode forward
Rotation angle of ref. volt. 45 ° -180 - 180 1
Forward section +/- 88 ° 0 - 90 1
Min. V0> for dir. determ. 4.00 kV 1.2 - 800 0.01
3I0> threshold value 2.000 A 0.04 - 64 0.001
Dir. determination delay 0.10 s 0 - 60 0.01
Operate delay 0.50 s 0 - 60 0.01
27/59TH 3rd Harm. 1
General
Threshold P min 0.4 0.00% - 100.00% 0.10%
Threshold V1 min 4.850 kV 0.029 - 19.091 0.001
Corr. factor for V03H> 0.000 kV 0 - 4.2 0.001
Dropout delay 1.00 s 0 - 60 0.01
V0 3. Harm> 1
Mode on
Operate & flt.rec. blocked no
Threshold 0.668 kV 0.029 - 10.5 0.001
Dropout delay 0.00 s 0 - 60 0.01
Operate delay 0.50 s 0 - 60 0.01
GCB
General
Ref. for %-values Rated normal current 6000.00 A
Rated voltage 10.50 kV
Breaker settings Current thresh. CB open 180.0000108 A 180 - 60000 1
Trip logic
Reset of trip command with I<
Circuit break.
Output time 0.10 s 0.02 - 1800 0.01
Indicat. of breaking values always
Manual close
Action time 0.30 s 0.01 - 60 0.01
CB open dropout delay 0.00 s 0 - 60 0.01
Control
Chatter blocking
Control
Spontan.indic.
CFC
Test support
Time managem.
General
Time zone and daylight saving time
Time sync.
Time source
Localization
Power system
General
S1 Side I3
CT 3-phase
General
CT phases
CT IN
CT 1
CT 2
CT 3
CT 4
Supv. balan. I
Supv. ph.seq.I
Supv. sum I
U3ph
VT 3-phase
VT 1
VT 2
VT 3
Supv. balan. V
Supv. ph.seq.V
Supv. sum V
VT miniatureCB
S2 Side I3
CT 3-phase
General
CT phases
CT IN
CT 1
CT 2
CT 3
CT 4
Supv. balan. I
Supv. ph.seq.I
Supv. sum I
Recording
Fault recorder
Control
Security
DIGSI access
MMS access
Web access
Security Logging
Sec. Ev. Logg.
General
Syslog server A
Syslog server B
Access control
Login attempts
User cache
Circuit breaker 1
General
Ref. for %-values
Breaker settings
Trip logic
Circuit break.
Manual close
Control
CB test
74TC sup.2BI 1
50BF Ad.CBF 1
Circuit breaker 2
General
Ref. for %-values
Breaker settings
Trip logic
Circuit break.
Manual close
Control
CB test
Operate curve
Starting detection
DC offset detection
Ext. fault detection
I-DIFF fast
Motor side 1
Mes.v.fail.det
General
General
Further settings
Side data
Measurements
67N Dir.OC-gnd-B1
General
Definite-T 1
67 Dir.OC-3ph-B1
General
Definite-T 1
50/51 OC-3ph-B1
Definite-T 1
50N/51N OC-gnd-B1
Definite-T 1
49 Th.overl.-A 1
49 Th.overl. 1
27 Undervolt.-3ph 1
General
Definite-T 1
Definite-T 2
59 Overvolt.-3ph 1
Definite-T 1
Definite-T 2
Motor side 2
General
General
Further settings
Side data
Measurements
11B-AAA000-000AC0-CB1BA1-CA1
Editable cells
Setting name Settings group1 Unit Min - Max Step 1KL4
Rated frequency 50 Hz 50
Minimum operate time 0.15 s 0 - 60 0.01 0.15
Set. format residu. comp. Kr; Kx Kr; Kx
Block monitoring dir. off off
Station name 77OP-V-100170 77OP-V-100170
Unit system SI x
Mode on on
Release threshold 1000 A 60 - 70000 1 1000
Threshold min/max 0.50 0.1 - 0.95 0.01 0.50
Delay failure indication 5.00 s 0 - 100 0.01 5.00
Mode on on
Delay failure indication 5.00 s 0 - 100 0.01 5.00
Mode on on
Release threshold 5.000 kV 0.027 - 17 0.001 5.000
Threshold min/max 0.75 0.58 - 0.95 0.01 0.75
Delay failure indication 5.00 s 0 - 100 0.01 5.00
Mode on on
Delay failure indication 5.00 s 0 - 100 0.01 5.00
Mode on on
Alarm delay 2.00 s 1 - 30 0.01 2.00
Mode on on
Holding int. start signal yes yes
Start via binary input no no
CB aux.cont. crit. allowed no no
with effective with effective
Dropout criterion criterion
Retrip after T1 no no
Threshold phase current 1000 A 60 - 70000 1 1000
Threshold sensitive 500 A 60 - 70000 1 500
Delay T1 for 3-pole retrip 0.050 s 0 - 60 0.001 0.050
Delay T2 for 3-pole trip 0.130 s 0.05 - 60 0.001 0.130
Minimum operate time 0.10 s 0 - 60 0.01 0.10
Mode on on
Operate & flt.rec. blocked no no
Operate delay 0.00 s 0 - 60 0.01 0.00
Threshold 0.20 I/IrObj 0.05 - 2 0.01 0.20
Slope 1 0.30 0 - 0.8 0.01 0.30
Intersection 1 Irest 0.67 I/IrObj 0 - 5 0.01 0.67
Slope 2 0.70 0.25 - 0.95 0.01 0.70
Intersection 2 Irest 2.50 I/IrObj 1 - 20 0.01 2.50
Starting detection yes yes
Thresh. startup detection 0.1 I/IrObj 0.1 - 2 0.1 0.1
Factor increasing char. 2.0 1 - 5 0.1 2.0
Max. perm. Start. time 5.0 s 0.1 - 180 0.1 5.0
Factor increasing char. DC 2.3 1 - 5 0.1 2.3
Threshold add-on stabiliz. 2.00 I/IrObj 1 - 20 0.01 2.00
Time of add-on stabiliz. 0.30 s 0 - 5 0.01 0.30
Crossblk. time add-on st. 0.30 s 0 - 2 0.01 0.30
Mode on x
Asym.fail.-DO on netw.flt. yes x
Asym.fail. - time delay 10.00 s 0 - 30 0.01 x
3ph.fail. - phs.curr.release 149.9956 A 60 - 70000 1 x
3ph.fail. - phs.curr. jump 149.9956 A 60 - 70000 1 x
3ph.fail. - VA,VB,VC < 0.525 kV 0.027 - 30.909 0.001 x
Switch-on 3ph. failure on x
SO 3ph.fail. - time delay 3.00 s 0.01 - 30 0.01 x
Mode on on
Operate & flt.rec. blocked no no
Directional mode forward forward
fundamental fundamental
Method of measurement comp. comp.
Blk. by meas.-volt. failure yes yes
Threshold 60.0000036 A 60 - 70000 1 60.0000036
Operate delay 0.80 s 0 - 60 0.01 0.80
Mode on on
Operate & flt.rec. blocked no no
Directional mode forward forward
fundamental fundamental
Method of measurement comp. comp.
Blk. by meas.-volt. failure yes yes
Threshold 2000.00012 A 60 - 70000 1 6000
Operate delay 0.80 s 0 - 60 0.01 0.80
Mode on on
Operate & flt.rec. blocked no no
fundamental fundamental
Method of measurement comp. comp.
Threshold 2000.00012 A 60 - 70000 1 6000
Operate delay 0.80 s 0 - 100 0.01 0.80
Mode on on
Operate & flt.rec. blocked no no
Threshold current warning 1640.0000984 A 60 - 70000 1 1640.0000984
Threshold thermal warn. 90.00% 50.00% - 100.00% 1.00% 90.00%
Dropout threshold operate 90.00% 50.00% - 99.00% 1.00% 90.00%
Emerg. start T overtravel 300 s 0 - 15000 10 300
K-factor 1.10 0.1 - 4 0.01 1.10
Thermal time constant 907 s 10 - 60000 1 907
Cooling time constant 6300 s 10 - 60000 1 6300
Imax thermal 3000.00018 A 60 - 20000 1 3000.00018
Imin cooling 750.000045 A 0 - 20000 1 750.000045
Temperature rise at Irated 70 K 40 - 200 1 70
Storage of thermal replica no no
Behav. at I> Imax therm. current limiting current limiting
Default temperature 40 °C -55 - 55 1 40
Minimal temperature -20 °C -55 - 40 1 -20
Current-flow criterion on x
Threshold I> 74.9978 A 60 - 20000 1 x
Mode on x
Operate & flt.rec. blocked no x
Blk. by meas.-volt. failure yes x
Measured value phase-to-phase x
fundamental
comp.
x
Method of measurement
Pickup mode 1 out of 3 x
Pickup delay no x
Threshold 5.000 kV 0.027 - 17.5 0.001 x
Dropout ratio 1.05 1.01 - 1.2 0.01 x
Operate delay 10.00 s 0 - 60 0.01 x
Mode off x
Operate & flt.rec. blocked no x
Blk. by meas.-volt. failure yes x
Measured value phase-to-phase x
fundamental
comp.
x
Method of measurement
Pickup mode 1 out of 3 x
Pickup delay no x
Threshold 6.825 kV 0.027 - 17.5 0.001 x
Dropout ratio 1.05 1.01 - 1.2 0.01 x
Operate delay 0.50 s 0 - 60 0.01 x
Mode on x
Operate & flt.rec. blocked no x
Measured value phase-to-phase x
fundamental
comp.
x
Method of measurement
Pickup mode 1 out of 3 x
Threshold 13.000 kV 0.027 - 30.909 0.001 x
Dropout ratio 0.95 0.9 - 0.99 0.01 x
Operate delay 2.00 s 0 - 300 0.01 x
Mode off x
Operate & flt.rec. blocked no x
Measured value phase-to-phase x
fundamental
comp.
x
Method of measurement
Pickup mode 1 out of 3 x
Threshold 13.650 kV 0.027 - 30.909 0.001 x
Dropout ratio 0.95 0.9 - 0.99 0.01 x
Operate delay 0.50 s 0 - 300 0.01 x
50 50 50
0.15 0.15 0.15
Kr; Kx Kr; Kx Kr; Kx
off off off
77OP-V-100170 77OP-V-100170 77OP-V-100170
0 0 0
1 1 1
0 0 0
1 1 1
2 2 2
1 1 1
settings group 1 settings group 1 settings group 1
false false false
120 120 120
x x x
x x x
x x x
x x x
automatic automatic automatic
false false false
false false false
x x x
x x x
x x x
x x x
x x x
x x x
x x x
on on on
1000 1000 1000
0.50 0.50 0.50
5.00 5.00 5.00
on on on
5.00 5.00 5.00
on on on
5.000 5.000 5.000
0.75 0.75 0.75
5.00 5.00 5.00
on on on
5.00 5.00 5.00
0 0 0
no no no
no no no
80 80 80
false false false
false false false
5 5 5
5 5 5
30 30 30
60 60 60
on on on
2.00 2.00 2.00
on on on
yes yes yes
no no no
no no no
with effective with effective with effective
criterion criterion criterion
no no no
1000 1000 1000
500 500 500
0.050 0.050 0.050
0.130 0.130 0.130
0.10 0.10 0.10
on on on
no no no
0.00 0.00 0.00
0.20 0.20 0.20
0.30 0.30 0.30
0.67 0.67 0.67
0.70 0.70 0.70
2.50 2.50 2.50
yes yes yes
0.1 0.1 0.1
2.0 2.0 2.0
5.0 5.0 5.0
2.3 2.3 2.3
2.00 2.00 2.00
0.30 0.30 0.30
0.30 0.30 0.30
x on on
x yes yes
x 10.00 10.00
x 148 148
x 148 148
x 5.775 5.775
x on on
x 3.00 3.00
on on on
no no no
forward forward forward
fundamental fundamental fundamental
comp. comp. comp.
yes yes yes
60.0000036 60.0000036 60.0000036
0.80 0.80 0.80
45 45 45
on on on
no no no
forward forward forward
fundamental fundamental fundamental
comp. comp. comp.
yes yes yes
6000 2000.00012 2000.00012
0.80 0.80 0.80
on on on
no no no
fundamental fundamental fundamental
comp. comp. comp.
6000 5400 2000.00012
0.80 0.80 0.80
on on on
no no no
1640.0000984 1640.0000984 1640.0000984
90.00% 90.00% 90.00%
90.00% 90.00% 90.00%
300 300 300
1.10 1.10 1.10
907 907 907
6300 6300 6300
3000.00018 3000.00018 3000.00018
750.000045 750.000045 750.000045
70 70 70
no no no
current limiting current limiting current limiting
40 40 40
-20 -20 -20
x on on
x 74.9978 74.9978
x on on
x no no
x yes yes
x phase-to-phase phase-to-phase
fundamental fundamental
x comp. comp.
x 1 out of 3 1 out of 3
x no no
x 5.000 5.000
x 1.05 1.05
x 10.00 10.00
x off off
x no no
x yes yes
x phase-to-phase phase-to-phase
fundamental fundamental
x comp. comp.
x 1 out of 3 1 out of 3
x no no
x 6.825 6.825
x 1.05 1.05
x 0.50 0.50
x on on
x no no
x phase-to-phase phase-to-phase
fundamental fundamental
x comp. comp.
x 1 out of 3 1 out of 3
x 13.000 13.000
x 0.95 0.95
x 2.00 2.00
x off off
x no no
x phase-to-phase phase-to-phase
fundamental fundamental
x comp. comp.
x 1 out of 3 1 out of 3
x 13.650 13.650
x 0.95 0.95
x 0.50 0.50
Thermal Overload
General
4201 Thermal overload protection ON
Therm Over Load
4202 K-Factor 1.05 0.1 - 4
4203 Time Constant 100 min 1 - 999.9
4204 Thermal Alarm Stage 90 % 50 - 100
4205 Current Overload Alarm Setpoint 4.375 A 0.1 - 4
4207A Kt-FACTOR when motor stops 1 1 - 10
4208A Emergency time 15 sec 10 - 15000
Measurement Supervision
General
8101 Measurement Supervision ON
5301 Fuse Fail Monitor OFF [23]
5310 Block protection by FFM YES [25]
MeasSupervision
8102 Voltage Threshold for Balance Monitoring 50 V 10 - 100
8103 Balance Factor for Voltage Monitor 0.75 0.58 - 0.9
8104 Current Balance Monitor 0.5 A 0.1 - 1
8105 Balance Factor for Current Monitor 0.5 0.1 - 0.9
8110A T Balance Factor for Voltage Monitor 5 sec 0 - 100
8111A T Current Balance Monitor 5 sec 0 - 100
Fuse Fail Mon.
5302 Zero Sequence Voltage 30 V 10 - 100
5303 Residual Current 0.1 A 0.1 - 1
5308A Delta Current Threshold (3phase) 0.1 A 0.05 - 1
Breaker Failure
General
7001 Breaker Failure Protection ON
Breaker Failure
7004 Check Breaker contacts ON
7005 TRIP-Timer 0.25 sec 0.06 - 60
7006 Pick-up threshold I> 1.7 A 0.05 - 20
Energy
Measurement
8315 Meter resolution Standard [12990]