This document provides information about a Delock 10/100 Mb/s Fast Ethernet Media Converter, including:
1. An overview of the media converter's functionality in extending a copper Ethernet network over fiber optic cable up to 20km.
2. Descriptions of the LED indicators on the front panel for monitoring the status of power, port links and data transmission.
3. Instructions for installing the media converter by connecting fiber and copper network cables to the appropriate ports and power supply.
4. Technical specifications for the media converter including standards compliance, connectors, operating mode, power requirements and environmental tolerances.
This document provides information about a Delock 10/100 Mb/s Fast Ethernet Media Converter, including:
1. An overview of the media converter's functionality in extending a copper Ethernet network over fiber optic cable up to 20km.
2. Descriptions of the LED indicators on the front panel for monitoring the status of power, port links and data transmission.
3. Instructions for installing the media converter by connecting fiber and copper network cables to the appropriate ports and power supply.
4. Technical specifications for the media converter including standards compliance, connectors, operating mode, power requirements and environmental tolerances.
This document provides information about a Delock 10/100 Mb/s Fast Ethernet Media Converter, including:
1. An overview of the media converter's functionality in extending a copper Ethernet network over fiber optic cable up to 20km.
2. Descriptions of the LED indicators on the front panel for monitoring the status of power, port links and data transmission.
3. Instructions for installing the media converter by connecting fiber and copper network cables to the appropriate ports and power supply.
4. Technical specifications for the media converter including standards compliance, connectors, operating mode, power requirements and environmental tolerances.
The Delock 10/100 Mb/s Fast Ethernet Media Converter LED indicator lamps serve as device monitoring and The DIP switch can be used to configure the TP and fiber series is designed to extend a copper based Fast Ethernet troubleshooting display. The following is the explanation interfaces. Top position is OFF, low position is ON. The network via fiber cable to a maximum distance up to 20 km. for each LED indicator lamp. default configuration is all DIP switches set to OFF. The 10/100 Mb/s Fast Ethernet Media Converter series is fully compliant with IEEE802.3, IEEE802.3U, 10/100Base-TX, and 100Base-FX standards. The installation and operation procedures are simple and straightforward. Operation status can be locally monitored through a set of diagnostic LEDs located in the front panel. Fig. 1: Front panel for dual fiber media converter Fig. 2: Back panel for dual fiber media converter
2. Package content LED Status Description No. Function Description
• Media Converter On Power supply is normal ON: Link fault passthrough PWR 1 LFP • AC-DC Power Supply Off Check power supply OFF: LFP disabled • User Manual On TP Port Link speed is 100 Mb/s ON: Pure converter mode 100M 2 Direct Wire Off TP Port Link speed is 10 Mb/s OFF: Store and Forward Switch 3. Installation On TP Link connected ON: Fast Forward disabled TP 3 Fast FWD • Fiber interface Blink Data transmission OFF: Fast Forward enabled Link/Act Connect a fiber cable from the media converter to the fiber Off TP Link fail ON: Force TP speed 4 TP_ Force network. The fiber connections must be matched - transmit On Fiber Port Link connected OFF: 10/100M Autonegotiation socket to receive socket, the TX, RX fiber cable must be FP Blink Data transmission ON: IEEE802.3x disabled paired at both ends. Link/Act 5 IEEE 802.3x Off Fiber Port Link fail OFF: IEEE802.3x enabled • TP interface On TP Port works in full duplex mode ON: 10M FDX/ Connect a TP cable from the 10/100BASE-T network to 6 Speed_Mode COL Off TP Port works in half duplex mode OFF: 100M the RJ-45 port on the media converter. ON: TP Port half duplex On Fiber Port signal detected • Power SD 7 Duplex_Mode Off Fiber Port signal not detected OFF: TP Port full duplex Connect the power adapter to the media converter and ON: Fiber Port half duplex check that the Power LED lights up. The TP-LINK/ACT 8 FX-Full OFF: Fiber Port full duplex and FP-LINK/ACT LEDs will light up when all the cable connections are correctly installed. 6. Technical Specifications Safety Instructions: Function Description 1. This product is suitable for indoor application only. Standard IEEE802.3 10Base-T standard 2. Put on the dust cover of fiber interface when not used. Protocol IEEE 802.3u 100Base-TX/FX standard 3. It is forbidden to stare at the TX fiber-transfer end with one RJ-45 connector naked eyes. Connector one SC duplex fiber connector Declaration of conformity TP cable Cat.3 UTP cable or better Products with a CE symbol fulfill the EMC directive (2004/108/EC), Operation which were released by the EU-commission. full duplex mode or half duplex mode mode The declaration of conformity can be downloaded here: http://www.delock.de/service/conformity Power supply +5 V DC 1 A WEEE-notice Environmental The WEEE (Waste Electrical and Electronic Equipment) directive, 0 °C ~ 55 °C temperature which became effective as European law on February 13th 2003, Relative resulted in an all out change in the disposal of disused electro 10/100 Mb/s Fast Ethernet 5 % ~ 80 %, non-condensing humidity devices. The primarily purpose of this directive is the avoidance of Dimensions ca. 26 mm x 70 mm x 95 mm electrical waste (WEEE) and at the same time the support of Media Converter recycling and other forms of recycling in order to reduce waste. 7. Ordering Information The WEEE-logo on the device and the package indicates that the User Manual Delock No 86215 86216 device should not be disposed in the normal household garbage. You are responsible for taking the disused electrical and SC Singlemode SC Multimode electronical devices to a respective collecting point. A separated Media Converter Media Converter collection and reasonable recycling of your electrical waste helps 9/125,10/125 µm 50/125,62.5/125 µm Fiber handling the natural resources more economical. Furthermore single-mode multi-mode recycling of electrical waste is a contribution to keep the Ptx dBm -15 ~ -8 -22 ~ -12 environment and thus also the health of men. Further information about disposal of electrical and electronical waste, recycling and SEN dBm ≤ -38 ≤ -30 the collection points are available in local organizations, waste management enterprises, in specialized trade and the producer of Overload ≥0 ≥ -3 the device. Product-No: 86215 / 86216 dBm Rev.1 www.delock.com Distance ≤ 20 km ≤ 2 km