Professional Documents
Culture Documents
Absco Space Saver Shed MODEL: 30152SECOK: 3.00mW X 1.52mD X 1.80mH, 2.08mH
Absco Space Saver Shed MODEL: 30152SECOK: 3.00mW X 1.52mD X 1.80mH, 2.08mH
MODEL: 30152SECOK
3.00mW x 1.52mD x 1.80mH, 2.08mH
SLAB
RETE
CONC
16 m
20
mm 3100m
For construction in non-cyclonic areas When laying concrete slab, ensure there
Wind rating: N2 as per AS4055-2012. is a rebated edge 25mm deep around
If you require a higher wind rating please contact the perimeter. This will help water egress
us: admin@absco.com.au or 1800 029 701 from the base of the shed.
MANU FA CT URED
Download the Absco
Sheds Assembly App
IN A US TR ALIA
GENERAL INSTRUCTIONS
• Before commencing any assembly, read through these instructions in detail to gain a thorough
understanding of assembly methods and associated details.
• Unpack the carton and carefully identify and check off all the parts against the parts described
and illustrated on "COMPONENTS PACKING LIST" pages.
SITE PREPARATION
• The site for the shed must be level. An uneven surface may result in misalignment of parts.
• The shed shall be erected on top of a reinforced concrete slab and anchored down appropriately
illustrated on “FINAL CONSTRUCTION” page.
TOOLS REQUIRED
metal & masonry
10mm drill bits
3mm drill bit
SAFETY NOTES
• Some parts may have sharp edges. It is advisable to wear gloves when handling these items and
safety glasses if drilling holes. Sensible shoes are highly recommended.
• Do not erect your shed in windy conditions.
• Ensure that the shed is securely anchored to a solid foundation immediately after construction is
completed.
• It is highly recommended to erect the shed with two or more people.
RECOMMENDED
STEEL SHEET
2 2045 X 773mm 262 1 STEEL SHEET
1915mm X 773mm 260L
STEEL SHEET
2 2045 X 773mm 263 1 STEEL SHEET
1915mm X 773mm 260R
1 STEEL SHEET
2045mm X 773mm 261L 4 STEEL SHEET
1610mm X 773mm 43S
1 STEEL SHEET
2045mm X 773mm 261R 2 STEEL SHEET
1785mm X 711mm 34A
1 STEEL SHEET
1725mm X 773mm A 1 STEEL SHEET
1725mm X 773mm B
2 61D 4 58C
C
D 58
61
CHANNEL CHANNEL
L = 1530mm L = 773mm
1 79A 2 58A
A
58
A
79
2 CHANNEL
81
E
81E 2 Part No. Here
89A
L = 1513mm JAMB L= 1785mm
1 58B 1 89C
B Part No. Here
58
CHANNEL
L = 1725mm JAMB L= 1725mm
1 55AL 1 55AR
AL AR
55 55
CHANNEL CHANNEL
L = 1496.5mm L = 1496.5mm
>> >>
IN IN
JO JO
1 55CL 1 55CR
CL CR
55 55
CHANNEL CHANNEL
L = 1496.5mm L = 1496.5mm
>> >>
IN IN
JO JO
1 55BL 1 55BR
BL BR
55 55
CHANNEL CHANNEL
L = 1496.5mm L = 1496.5mm
>> >>
IN IN
JO JO
1 81BL 1 81BR
BL BR
81 81
CHANNEL CHANNEL
L = 1496.5mm L = 1496.5mm
> > >>
IN IN
JO JO
2 81AL 2 81AR
AL AR
81 81
CHANNEL CHANNEL
L = 1496.5mm L = 1496.5mm
DOOR
6 2
J
12A
CS
CSJ STRAP
CHANNEL JOINER L: 165mm
L = 200mm
1 DRILL 1 FAST038
To assemble each panel, the perimeter channels are secured to the top and bottom of each panel.
Gently tap the channel over the SNAPTiTE lugs on the sheet, working along the sheet.
Each perimeter channel must finish flush with the edges of the sheets. Simply tap the channel along
the sheets until each end is neatly flush. If you need to remove channels from the panels, slide it off
from the side.
FASTENING SYMBOLS
= = = = =
CSJ
=
JOIN>> SJ
JOIN>> <<JOIN JOIN>> J
Step 1. Step 2.
Position the channels and the Join the first channel to the CSJ Push down one side of the CSJ
CSJ joiner so the centre of by inserting the centre of the until you hear a ‘click’.
the CSJ is in line with the end CSJ, on an angle, to the end of
of each channel to be joiner the channel where the JOIN>>
together. text is marked.
...
20mm 15mm
Finished Spliced
Channel
AL
81
m m = 1x 55A
93
29
AL
55 = 1x 55C
AR
81 CL
55 = 1x 55B
2x 81AR
2x 81AL
AR BL
55 55 = 1x 81B
1x 55AR
1x 55AL
CR BL
55 81
1x 55CR
1x 55CL
BR
55
1x 55BR
1x 55BL
BR
81
1x 81BR
1x 81BL
81A
43S
43S
43S
OVERVIEW OF ROOF COMPONENTS
81A
43S
88J
22A
B
81E
55A
A
61D
34A
260L
261L
89A
79A
91A
91A
90A
89A
55C
262
OVERVIEW OF WALL COMPONENTS
34A
263
61D
260R
263
261R
262
55B
81E
81B
262
263
263
262
55B
E
APT iT
SN
81B
E
APT iT
SN
261R
261L
260L
61D
AP TE
SN T i
81E
E
A P T iT
SN
61D E
APT iT
SN
E
APT iT
SN
81E
43S
43S
43S
43S
81A
88J
D
E
APT iT
SN
81A
D E
APT iT
SN
88J
89A
FRONT PANEL ASSEMBLY
89A
34A
34A
E
APT iT
SN
55A
APT iT
E 90A
SN
E
APT iT
79A SN
55C
E
APT iT
SN
SNAPT iTE
58B
D
B
D
12A D
A
D
SNAPT iTE
58C
58A
SNAPT iTE
89C
Vertical door channels are
installed in the opposite
58C
orientation compared to the
horizontal door channels.
91A
91A
The two holes required to connect the padbolt hasp for each door have not been pre-punched, to
allow for proper alignment, position each hasp centrally over the padbolt shaft and drill 3mm holes and
secure with screws.
Absco Industries Assembly Instruction Manual Model: 30152SECOK 18/11/18 1.4 16
ABSCO SPACE SAVER SHED
MODEL: 30152SECOK
3.00mW x 1.52mD x 1.80mH, 2.08mH
PANEL CONSTRUCTION
NOTE: Take care to ensure that all wall panels are not upside down. The top channels of each panel
are pre-punched for attaching roof sheeting. The base channels are not pre-punched.
D D
250
600
600
600
600
250
FINAL CONSTRUCTION
250
250
ANCHORING OF SHED
Location of 15
concrete anchors
250
250
D
250
360
360
360
360
250
D
D D
D
D
D
D
D
D D
6-12 Activity St, Acacia Ridge QLD 4110 AU: 1800 029 701 admin@absco.com.au
PO Box 119, Acacia Ridge QLD 4110 N Z: 0800 466 444 www.abscosheds.com.au
6-12 Activity St, Acacia Ridge QLD 4110 AU: 1800 029 701 admin@absco.com.au
PO Box 119, Acacia Ridge QLD 4110 N Z: 0800 466 444 www.abscosheds.com.au
• We are pleased to advise we warrant that the steel coating will not rust, crack, flake peel or blister for 20
years from date of purchase, when installed within Australia.
• This warranty does not apply to surface deterioration of panels caused by ‘Swarf” (Tiny particles of
steel debris left from cutting, grinding or drilling operations) that has not been removed after building
construction, or as a result of contact with damp soil, chemicals, fertilisers or other corrosive substances.
• This warranty covers any Absco product used for normal domestic use and installed in accordance with the
installation instructions.
• The warranty does NOT cover Damage caused by storms, wind, rain snow or poor foundations.
• This warranty does NOT cover ABSCO products installed in severe coastal, industrial or other highly
corrosive environments. The warranty does not cover fasteners (screws, nuts, bolts, rivets, hasps or sliding
padbolts).
• The warranty is limited to replacement and delivery of components and does not include any labour or
installation costs. The benefits given by the warranty are in addition to your other rights and remedies
under a law in relation to the goods or services to which the warranty relates.
• The warranty applies to the exclusion of all other representations, guarantees or warranties express or
implied, our goods come with guarantees that cannot be excluded under the Australian consumer law and
is not transferable. You are entitled to a replacement or refund for a major failure and for compensation
for any other foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if
the goods fail to be of an acceptable quality and the failure does not amount to a major failure. For further
information go to http://www.consumerlaw.gov.au
• Please retain a proof of purchase (sales docket or invoice) or register your warranty within 30 days of
purchase here: www.absco.com.au/register_warranty.php
• In the unlikely event a warranty claim is made, it must be supported by photographic evidence and details
of the defect, including component part numbers, together with proof of purchase documentation (or
on-line registration of purchase) and forwarded to the address below. Upon receipt of the warranty claim,
the Customer Service Manager will contact you within three business days to advise you of the assessment
outcome of the claim, which may include your expenses incurred in making the claim.
THE CUSTOMER SERVICE MANAGER, ABSCO INDUSTRIES, PO BOX 119 ACACIA RIDGE QLD AUSTRALIA 4110