Professional Documents
Culture Documents
Lift - 1 Lift - 8: Default PIN: 123
Lift - 1 Lift - 8: Default PIN: 123
Lift - 1 Lift - 2
Control Cabinet
Lift - 3
Control Cabinet
Lift - 4
Control Cabinet
Lift - 5
Control Cabinet
Lift - 6
Control Cabinet
Lift - 7
Control Cabinet Lift - 8
Control Cabinet Control Cabinet
DATA
DATA
DATA
DATA
Cable Entry
+V
+V
+V
+V
SHLD
SHLD
SHLD
SHLD
SIG
SIG
SIG
SIG
0V
0V
0V
0V
SHLD
SIG
0V
+V
Cabinet
Earth
SHLD
SHLD
SHLD
SHLD
DATA
DATA
DATA
DATA
SIG
SIG
SIG
SIG
0V
0V
0V
0V
+V
+V
+V
+V
Note: Power can be connected
directly to LX/M Board or one
Download the Complete Manual from the following address: of the connected CD-LX/TE boards
TECHNOLOGIES
www.designcom.com.au http://designcom.com.au/clientFiles/LX8ProductDoc.zip
LX-8 intercom system Rev: 1.0.0923.4 Date: 2-05-09
Installation wiring diagram Sheet 1 of 2 Drawing Number: 0923LX8
END
TOP
i END
VOL +
ON / OFF
Press and HOLD for 3 seconds (4 beeps) TOP
VOL +
CAR
VOL -
CAR
VOL -
PIT
(2 beeps)
PIT
emFONE
Lift number 1 or 2 Lift position 2 = CAR
emFONE
DATA
SIG
SIG
ON / OFF
Press and HOLD for 3 seconds (3 beeps)
0V
0V
+V
+V
END Press and HOLD for 3 seconds (3 beeps)
1 = TOP
SHLD
SHLD
3 = PIT Lift position
4 = SPARE
Lift Car-1 Lift Car-1
Relay-2 Relay-2
Call Answered Call Answered
Relay-1 +
Microphone is polarized Relay-1 +
Microphone is polarized
Alarm Acknowledged External Speaker Alarm Acknowledged External Speaker
emFONE R emFONE R
www.emfone.com
PIT www.emfone.com
ON / OFF
ALARM
1
4
2
5
3
6
External Microphone
CD-LX/SK ON / OFF
ALARM
1
4
2
5
3
6
External Microphone
i 7 8 9 i 7 8 9
* 0 # * 0 #
CAR CAR
END START END START
www.designcom.com.au www.designcom.com.au
CD-LX/SK TOP
CAR
VOL +
VOL -
TOP
CAR
VOL +
VOL -
PIT
PIT
10Kohm 10Kohm
The Second PIT
SHLD
SHLD
DATA
DATA
SPR
SPR
Button Button
SIG
SIG
0V
0V
+V
+V
ALARM
Sense Sense
unit should be wired
ALARM
emFONE
Resistor emFONE Resistor
DATA
DATA
SIG
0V
+V
+V
first PIT.
SHLD
and DO NOT run cables 10Kohm 4. Minimum distance between the microphone and speaker
Button
Telephone Line
in the same ducts as the Sense
Resistor
should be 120mm.
Cable Entry Lift installation.
5. Install a 10K ohm resistor across the Alarm button.
3. Do not install the unit CD-LX/SLX Alarm Button 1
next to a fan or high noise Dry Contacts
www.emfone.com
Telephone
Line system unless all cabling
is completed and 1. The COP manufacturer MUST ensure that the mounting studs and the speaker
checked. and microphone grills are correctly engineered. If the microphone hole does not
match the module then the unit may not operate at an acceptable level. There must
1-pair shielded cable 1-pair shielded cable CD-LX/SL
also be NO air gap between the unit and the panel that is being installed.
for DATA & +Voltage for SIGNAL & GROUND
to meet Ip54 rating. 1. Remove the keyboard and the 1. Follow the same instructions
electronics from the main case. as per the PIT station.
To Machine 2. Cut and drill the conduit entry point on 2. Locate an appropriate
Room bottom of the case, or cut the cable entry location for the unit. Ideal
from the back of the case if the cables are suggestion will be as per the
Cable entry coming from the wall. “X” markings on the diagram
from the wall below.
3. Use 3 screws to mount the main case to
the appropriate location in the PIT
Trailer
4. Use small diameter cable between the Cable
circuit board and the terminating point.
Make sure the cables in the terminating X (1) Inspection
Control Unit
point are twisted together and fit screw
caps.
X (2)
Cut and drill
conduit entry emFONE