40 Troubleshooting
Troubleshooting by failure code (Display of code)
Failure code [DHU2KX] Out of Range of Acc. Oil Press. S. (F) moo sonuax.
008204)
Aatontavel | Falure.cods |, _,,,, [outof Range of Acsumulator OT Pressure Sensor F)
Lot DHU2KK allure "|(Retarder hoist controller system)
Daiailof [= Voltage of signal circuit of Font accumulator pressure sensor drops Below 0.3 Vor
failure increases above 4.7 V.
Action of Ts None in particular.
controtler_|* None in particul
Problem on |,
machine _|* None
> Signal fom pressure sensor can be checked with monitoring function, (Coder 36500
Related (MPa) oF 35506 (V))
information |+ T-adapteris not prepared for connector 825.
‘+ Method of reproducing failure code: Tum starting switch to ON position.
No. Cause Procedure, measuring location, orleria and remarks
4, Turn star
2. Insert T-adapters to connector 122.
3, Tum sta
ring switch to OFF position
ring switch to ON position.
Jopen circuit in wiring hamess
2 |(wire breakage or defective
contact of connector)
1 [Detective sensor power suppiy| + if power supply voltage is unusual, perform checks on causes 204
circuit If no failure is found, sensor power supply system is defective.
Power
supply Between J22 (female) (1) and (4) 461054
voltage v
1, Tum starting switch to OFF position,
2. Disconnect connectors BRC1 and 825, and connect T-adapters to
fomale sides of BRC1 and BRC2.
Resis-
tance
[Between BRC2 (female) (86) and B25 (female)
2)
+ If power supply voltage in check on cause 1
is normal, this check is not required Max. 1.0.
Between BRC1 (female) (4) and B25 (female)
a)
[+ If power supply voltage in check on cause 1
is normal, this check is not required Max. 1.0
Between BRC2 (female) (1) and B25 (female)
(3)
Max. 1.0
Ground faut in wiring hamess
41. Tum starting switch to OFF position,
2. Disconnect connectors BRC2 and 825, and connect T-adapters to
3 female side of BRC2.
(contact with ground circu) | Rosie. [Between BRCZ female) (and ground in 7M
tance [Between BRC2 female) (36) and ground [Min 1M
7, Tum starting swith to OFF positon
Hot short circuit in wiing | 2° Disconnect eonnector B25,
4 |namese 3 inser T-adapters into connector BRC2
(contactwith 24 V circuit) | 4. Tum staring switch to ON postion,
Vollage Between BRG2 (36)and ground Wax 7V
7, Tum starting switch to OFF positon,
2: Insert adapters to connector J22.
5 [etectve ont accumulator i | 3: Tur starting switch to ON position
pressure sensor Sensor
‘output [Between J22 (2) and (4) ostea7
voltage
00-300 40-46540 Troublesho:
‘Troubleshooting by failure code (Display of code)
Ne. Cause Procedure, measuring localion, crteria and remarks:
Ino Talure is found by above checks, retarder holst controller may Be
defective. (Since this is an internal defect, troubleshooting cannot be
performed.)
% Reference
4. [Detective retarder hoist 1. Tum starting switch to OFF position,
controller 2. Insert T-adapters to connectors BRC1 and BRC2.
3._Tum starting switch to ON position.
[Between BRC2 (1) and BRC1 (4) 40054
Voltage sar
[Between BRC2 (36) and BRC1 (4) «
Circuit diagram related to accumulator oil pressure sensor
faterder hoist contro! ier
act (0R626-248
Avatoe GHD )¢ DO 2
07
C2 (DRC26-408 conc 6-708)
se \¢ \4
nem Jy \¢
icc snnen | \a
40-466 Hma0o-smo