Professional Documents
Culture Documents
(1988) Effect of Reheating On Low Temperature Toughness of Type 308L Austenitic Stainless Steel Weld Metal
(1988) Effect of Reheating On Low Temperature Toughness of Type 308L Austenitic Stainless Steel Weld Metal
低 温 じん 性 に 及 ぼ す 再 熱 の 影 響
オ ー ステ ナ イ トス テ ン レ ス鋼 溶 接 金 属 の低 温 じん 姓(第5報)
恩沢 忠 男,高 崎 明 人,関口 優
76
溶 接 学 会論 文 集 第6巻(1988)第2号273
An auther's previous paper had reported on the effect of heat-treating on the low temperature tough-
In this paper, the same study on Type 308L weld metal was carried out whose the heat-treating con-
dition was at temperature from 923 to 1523K for time from 2s to 24h.
In heat-treating the weld metal with ƒÂ ferrite above 2%, the absorbed energy decreased with increasing
the amount of prior a ferrite and particulary in the case of heat-treated temperature of 923K, degradation
of absorbed energy was remarkable. This tendency was opposite to the result of Type 316L weld metal.
This aws suggested that the addition of Mo was shifted Time-Temperature-Sensitization curve of the weld
In the other hand, the absorbed energy of fully austenitic weld metal was constant independent of
In the Type 316L weld metal reported previously, the absorbed energy tended to rise slightly by
heat-treating for time up to 120s. In this Type 308L weld metal, however, such a tendency was not
observed. This was considered to be attributed to somewhat good coherency of ƒÂ/ƒÁ intreface as com-
pared to the case of Type 316L weld metal, in particular, in case of eutectic ƒÂ ferrite weld metal.
The decomposition of ƒÂ ferrite in this Type 308L was somewhat slower than that in the Type 316L.
Key Words: Austenitic Stainless Steel, Weld Metal, Low Temperature Toughness, Heat Treatment,
Delta Ferrite
77
274研 究論 文 恩 沢 他:308Lオ ー ス テ ナ イ トス テ ン レ ン鋼 溶 接 金 属 の 低 温 じん性 に 及ぼ す 再 熱 の影 響
Fig. 1 Relation between absorbed energy and delta ferrite content before PWHT for various heat
treating times
Fig. 2 Relation between absorbed energy and heat treating time for various weld metals
78
溶 接 学 会論 文 集 第6巻(1988)第2号275
オ ー ス テ ナ イ ト組 織 の 場 斜(a),吸 収 エ ネル ギ ー は 熱処 理 とが 明 らか で あ る.
温 度 及 び 時 間 に 関 係 な くほ ぼ 一 定 で70J程 度 で あ る. 初 晶 δ フェ ライ ト組 織 の 場 合 の 吸収 エ ネ ル ギ ー と 熱
これ らのSEM破 面 は 全 て 完 全 デ ィンプ ル を 示 して お 処 理 時 間の 関 係 をFig.2(c)及 び(d)に示 す.熱 処 理 温 度 が
り,熱 処 理 時 間86-4ks(24h)ま で の再 熱 に よ る じん 性 1123Kで は(C)及び(d)共に,熱 処 理 時 間が 増 加 して も吸
の 低 下 は み られ な い. 収 エ ネ ル ギ ー は ほ とん ど変 化 しな い.こ れ らの 破 面 は 企
一 方,共 晶 δ フ ェ ラ イ ト溶 接 金属(b)の 吸 収 エ ネ ル て 完 全 デ ィ ンプ ルを 示 して いた 。 しか し,熱 処 理 温 度 が
ギ ーは 熱 処 理 温度 が 異 な って も顕 著 な変 化 は 認 め られ な 923Kで は,吸 収 エ ネ ル ギ-は 熱 処 理 時 間 が2∼120sま
い.ま た,両 熱 処 理 温度 と も熱 処 理時 間600sま でで は で は ほ とん ど変 化 しない が,そ れ 以 上 熱 処 理 時 間 が 増 加
吸 収 エ ネル ギ ーは ほ とん ど 一定 で,溶 接 の ま ま材 の そ れ す る と大 き く低 下 す る 傾 向 を示 して い る.こ の 場 合 の
と同 じ値 を 示 して い る.し か し,そ れ 以上 熱 処 理 時 間 が SEM破 面 をFig.4に 示 す.熱 処 理 時 間 が120sま で は
は セ ル ラ ーデ ン ドラ イ ト境 界部 に 沿 って 破 壊 して い る こ
79
278研 究論文 恩 沢 他:308Lオー ステ ナ イト ステ ン レス鋼 溶 接 金 属 の 低 温 じん 性 に及ぼ す 再 熱 の 影 響
80
溶 接 学会 論 文 集 第6巻(1988)第2号277
δ フ ェ ラ イ ト量 の異 な る1パ ス の3081.サ ブマ ー ジ Aging Behavior of Types 308 and 308 CRE Stainless Steel
Welds Weld. J., 63-8(1984), 246s-253s
ア ー ク溶 接 金 属 を923Kか ら1523Kの 温 度 で2sか ら
81