Professional Documents
Culture Documents
TR10-16F Series Manual
TR10-16F Series Manual
TR Multi-Freq Series
Multi-Frequency Tone Remote
1/2013
Dimensions 9” x 4” x 7”
Audio Output to Speaker 2 Watts at 3% THD into 8 ohms, using supplied wall pack
Frequency Response +/- 3dB from 300 to 3000Hz, except at notch frequency. 1000Hz reference.
Audio Compression Less than 3dB increase in output with 30dB increase in input beyond threshold.
Threshold is adjustable from -20dBm to +10dBm.
2
TR10-16F REMOTE CONTROL CONSOLE
GENERAL DESCRIPTION
This manual covers the TR10-4F, TR10-8F, TR10-12F, and TR10-16F series remotes. All models will be
referenced as TR10-16F from here on.
The TR10-16F series multi-frequency tone remote allows users to reliably control up to sixteen channels on a
conventional or trunked two way base station or repeater via twisted pair wiring.
Receive audio is transferred to the handset earpiece when taken off hook.
Parallel Status Indication allows the remote to update when a channel change function is performed from another
remote on the system. The TR10-16F activates the Parallel Transmit Indication (PTI) by lighting the TX LED when
parallel remotes key and can also be configured to mute the speaker by enabling the crossmute function to prevent
audio feedback when remotes are in close proximity.
Standard features include volume control, individual frequency selection switches with indicators, front panel PTT
switch, LED transmit indicator, monitor function with LED indicator, intercom function with LED indicator, receive
and transmit audio compression, 2175Hz receive notch filter, PTI indication, and crossmute.
The TR10-16F is available in many optional configurations. Some of the available options include: (-DM) Desk mic
replaces the handset, (-GN) Gooseneck mic replaces the handset, (-FS) Foot switch to activate PTT, (-4F) four
channel frequency control, (-8F) eight channel frequency control, (-12F) twelve channel frequency control, (-16F)
sixteen channel frequency control, (-4W) four wire operation, (-FD) full duplex operation.
3
TR10-16F REMOTE CONTROL CONSOLE
TR SERIES
F1 F2 F3 F4
F5 F6 F7 F8
INTERCOM
VOLUME TX MONITOR
Front panel
Figure 1 shows a view of the front panel of the TR10-16F series. The front panel features intercom and monitor
functions, Tx function, and volume control for speaker audio. All functions and features include indicators except
the volume control.
INTERCOM Button: When pressed and held, provides intercom capability to other parallel remotes without keying
the radio. A yellow LED will light as long as the intercom button is pressed.
MONITOR Button: Sends the monitor tone burst placing the radio into monitor mode to disable coded squelch
(CTCSS/CDCSS) so the line may be monitored before transmitting. A yellow LED lights as long as the monitor
button is pressed.
TX Button: When pressed and held, allows the user to key the radio and transmit. A red TX LED lights as long as
the button is pressed. The TX LED also lights when any PTT occurs from the TR10-16F and will also light as a
parallel transmit indication (PTI) that parallel remotes are currently transmitting.
Volume Control: Adjusts the level of the audio heard over speaker.
4
TR10-16F REMOTE CONTROL CONSOLE
INSTALLATION
The TR10-16F series tone remote will operate with any remote system using the EIA standard tone control format.
Power
The remote is powered from 120V 60Hz AC using the supplied wall pack transformer. In most cases, when the
supplied wall pack is used, a standard grounded outlet is acceptable. An ideal ground point would consist of a ½
inch copper rod driven six feet into the earth with at least a #16 AWG copper wire connecting it to the GND terminal
of the remote, taking the shortest path possible.
Phone lines
The TR10-16F is designed to work with a high quality voice grade circuit such as leased lines or in-house twisted
pair wiring. Circuits and wiring must have no dial tone, talk battery, or signaling. DC continuity is not required.
Connections are made to the remote, via the supplied 6 foot modular cord. The TR10-16F comes standard two
wire operation. Four wire and full duplex operation are optional. Options must be installed for four wire (-4W) or full
duplex (-FD) to be operational. Table 2 contains jumper configuration for 2 wire, 4 wire, and full duplex.
Tx/Rx Tx Rx
J3 J3
Two wire utilizes the center red/green pair for Tx and Rx. Four wire and full duplex utilize the red/green pair for Rx
and the yellow/black pair for Tx.
Parallel Operation
Parallel remotes on the same line are an integral part of the remote control system which allows more users and
also allows future expansion of the system. Connecting multiple remotes requires line impedance settings to be
configured for optimal performance of the system.
Line Impedance
When several remote control units are connected in parallel on one line, the total system impedance will decrease
to a point where operation is degraded. This occurs when 3 or more remotes are connected in parallel. Up to ten
remotes may be connected in parallel on the same phone line. The maximum loss between any remote and
termination panel must not exceed 20dB.
To compensate for this effect, the TR10-16F remote provides dip switch selectable 600 ohm or 5000 ohm line
impedance settings. Line impedance settings are configured via the dip switch located on the bottom of the unit
(Table 1 – S1-1). In parallel remote installations using the same phone line, dip switch 1 should be in the OFF
position (5000 ohms) in all remotes except the last one in the chain. The last remote on the line should have dip
switch 1 in the ON position (600 ohms)
Crossmute
The crossmute feature allows the remote to mute the speaker during PTT from a parallel remote to prevent audio
feedback. Crossmute is ideal when multiple remotes are installed in close proximity that audio feedback occurs on
parallel remote speakers. No additional wires between remotes are needed to activate the crossmute feature. The
crossmute feature works by decoding the PTT control tones when parallel remotes key and mutes the speaker
cutting off the audio path to feedback through. Intercom has no effect and will be heard on parallel remotes.
The crossmute feature is enabled when shipped from the factory. Configuring the crossmute feature is dip switch
selectable with dip switch 6 located on the bottom of the unit (Table 1 - S1-6). “On” disables crossmute, “Off”
5
TR10-16F REMOTE CONTROL CONSOLE
enables crossmute. Note: speaker becomes active all the time regardless of the handset in the off hook position
when crossmute is disabled.
Level Settings
Typical level settings require only a small flathead screwdriver for adjustments and a standard phillips head
screwdriver to remove the screws securing the top half of the housing to access most of the adjustments. Some
adjustments can be accessed from the bottom of the remote.
The following adjustments assume the termination panel has been properly installed and the phone line meets
above requirements.
Microphone Sensitivity
R75 controls the microphone audio level into the transmit compression circuits and therefore acts as a sensitivity
control. The potentiometer has been factory set to provide adequate compression for normal voice audio with a
relatively quiet background noise level. Adjustment is located on the bottom baseboard and is also accessible from
the bottom of the remote.
Earpiece Adjust
R96 controls the Rx audio into the earpiece. The potentiometer has been factory set to provide a comfortable
earpiece level for most environments. Adjustment is located on the bottom baseboard and is also accessible from
the bottom of the remote.
While applying an RF signal modulated with 1000Hz tone at 60% system deviation to the base station receiver,
adjust the termination panel line output for 0dBm to the phone line. Adjust all remotes used as follows:
Note: Adjustments and measurements are located and taken on the base board.
Tx Line Output
This level is preset at the factory for 0dBm out to the phone line and may not require readjustment at installation. If
needed, the procedure used is as follows:
Note: Adjustments are located on the baseboard of the TR10-16F and measurements are taken at the
termination panel which may require two people to perform the procedure.
a. With the handset off-hook, if applicable, press the intercom button (the handset PTT can be used but
audio may be passed over the air) and adjust the Tx audio pot (R63) while saying and holding the word
“Five” into the handset until 0dBm is measured across the phone line at the termination panel.
b. Turn “on” dip switch 7 (located on bottom of unit) and key the remote to lock up the 1950Hz function
tone. Adjust R80 tone level until the 1950Hz function tone measures 0dBm across the phone line at
the termination panel.
c. Return dip switch 7 to the “off” position.
Rx Notch Filter
The Rx 2175Hz notch filter is tuned at the factory and should not be readjusted. In the event that the notch filter
needs to be adjusted, the procedure follows:
6
TR10-16F REMOTE CONTROL CONSOLE
a. Apply 0dBm, 2.2Vpp, 2175Hz signal on the red and green phone line input.
b. Using a dual channel scope in the X-Y mode, connect one probe to U2 pin 14 and the other probe to U3
pin 8.
c. Adjust R39 until the lissajous pattern closes to a flat line. Remove probes.
d. With the scope in the single channel mode, connect probe to U3 pin 14. Adjust R38 to obtain a minimum
signal level. Readjust R39 slightly to further reduce the signal level. Recheck R38 then R39 for the
smallest minimum signal level achievable.
a. Apply 0dBm, 2.2Vpp, 2175Hz signal on the red and green phone line input.
b. Using a test clip, jumper U10 pin 7 to left side of R6.
c. Using a dual channel scope in the X-Y mode, connect one probe to U1 pin 14 and the other probe to U8
pin 8.
d. Adjust R52 until the lissajous pattern closes to a flat line. Remove probes.
e. With the scope in the single channel mode, connect probe to U8 pin 7. Adjust R52 to obtain a minimum
signal level. Adjust R54 to further reduce the signal level. Recheck R52 then R54 for the smallest
minimum signal level achievable.
OPERATION
The operation of the TR10-16F is designed, with the end user in mind, without the complexity of multi-
programmable buttons and over populated LCD displays. Individual buttons and indicators are used to provide
straight forward operation.
When power is applied to the unit, the F1 frequency is selected with indicator lit and is now ready for use.
Selecting a Frequency
Pressing one of the F1 – F16 buttons will select the frequency and will send the corresponding function tone out the
phone line and will light a green LED next to the frequency button pressed. The last selected frequency will be the
active frequency until a different frequency button is pressed.
Transmitting/Initiating Calls
Select the frequency to transmit on. Press and hold the front panel TX button, handset PTT button, or deskmic
PTT button to activate and speak into the corresponding mic. When a PTT occurs from the handset, front panel, or
deskmic the other mics are inactive to eliminate background noise during the transmission.
Use of the handset is recommended in noisy environments or when private conversation is desired.
Use of the front panel internal mic should only be used in low noise environments. The panel mic is not design to
be used regularly and is intended for quick, short responses.
Note: when the handset is off hook, transmit audio is passed through the handset mic no matter which PTT is
activated.
Intercom
Press and hold the front panel INTERCOM button and speak into the front panel mic when on hook. Speak into the
handset mic when off hook. Intercom audio will only be heard on parallel remotes and will not activate the radio’s
PTT or transmit audio over the radio.
Receiving Calls
Rx audio will be heard over the speaker while on hook and transferred to the earpiece when the handset is lifted off
hook. Parallel transmit audio from other remotes are heard on the unit unless the crossmute feature has been
enabled and activated.
7
TR10-16F REMOTE CONTROL CONSOLE
8
TR10-16F REMOTE CONTROL CONSOLE
AUDIO CONTROLS
The TR10-16F series remotes have a number of potentiometers. Following are tables indicating the pot
designation, control, and location. Audio controls are provided below for quick reference. Note that some controls
can or will effect other settings.
9
TR10-16F REMOTE CONTROL CONSOLE
WARRANTY
CPI Communications warrants each product manufactured by it to be free from defective material and workmanship
and agrees to remedy any such defects or to furnish a new part in exchange for any part of any unit of its
manufacturer which under normal installation use or service disclosed such defects, provided the unit is delivered
by the customer to our authorized service center intact, with all transportation charges pre paid within two years
from the date shipment to original purchaser. Exceptions are semiconductors which carry only the manufacture’s
standard warranty and lamp indicators and fuses which are warranted to be operational when shipped from the
factory. No credit will be given for unauthorized repair. This warranty does not extend to any of our products which
have been subjected to misuse, neglect, accident, incorrect wiring not our own, improper installation, or to use in
violation of instructions furnished by us nor extended to units which have been repaired or altered outside of our
factory or authorized service center, nor to cases where the serial number thereof has been removed, defaced, or
changed, nor to accessories used therewith not of our own manufacture, not to furnish or appearance items.
This warranty is in lieu of all other warranties expressed or implied and no person is authorized to assume for us
any other liability in connection with sale of our products. CPI Communications shall never be liable for
consequential or indirect damages.
10
900-TRBB-200 Board View
U8 C 45 C 46
C P I C O MMUNIC AT IO NS ,INC . C 1994 R 50 R 55 C 47
C 29
R 24
U1 R 51 R 56
C1 Q1 C2
C 30
Q4
R 25
R 52
D7
R 57
C 18
C 19 R 58
R1 R 97 D9
C4
R 53 R 59
C3 R 26
TB1
C 20
R2 D8
R 27
R 54
R 60
R3 R 28
R4 R 29 C 31 F1
R 61
R5 D4
C 21 T1 D10 D11
R6 D3 R 62 C 49
C 22
U15
C 48
C 50
R7 R 30 U9
R 31
J U4
Q6
J U2
J U3
R8 U2
C 51 R 98 R 122
R 32
J U1
Q2 R 123
C5
C6 R 33 R 99
T2 R 124
C 52
R 100
C 23
R 81 R 125
D1 R 101
R 82 Q7
NO
NC
Q5
C 24
W
S1 Y1
C 53
R 83
U16
D2
R 84 R 112
C8 C 35
C7 R 34 U17
C 32 C 33 R 85 R 102
R9 R 35 V1
R 10 C 34 C 64 R 86 R 103
R 36
C9 R 87 R 104
R 37
R 11
L1 U10 D12
C 65
V2
C 62
C 61
C 63
L2 R 88 U12
V3
C 43
R 12 L3
C 44
R 13 C 67
J3
R N1
R 14
J U5
R 105
C 66
L4 V4
C 10 U3 R 63 R 76
C 37
J2
C 25
R 15
C 11 J U7
C 54
J1 U 11
C 36
R 16 R 89
J U8
R 106
C 55
R 17 R 38 C 39
C 38 R 90 R 107
R 18 R 64 R 77
C 12 R 39 J U9
R 78
R 40 R 108
R 19 R 65 C 56 R 113
U4 R 79 S2 R 128
R 41 R 127 R 66
C 40
R 67 C 58 Q8 R 114
C 13
R 42 U6 R 68 C 57 Q9
R 69 U7
R 91 U13 U14
C 15
C 14
C 26 R 70 R 115
C 41
R 20 R 71 R 92 R 116 J4
R 21 R 72 R 93 R 117
R 73 R 94 R 118
C 27
R 23 C 42
R 22 R 74 D13
C 59
C 16 R 126 R 95 R 119
R 47 R 120
C 28 R 49
R 43 R 109
J U6
R 121
D5 C 60
R 75 R 96
R 44 R 80 R 110 R 111
R 45 D6
Q 10 Q 11
Q3 C 17
U5 R 46
T R S E R IE S 700-T R B B -200 REV C S /N
Component Layout 700-TRML-200
1 2 3 4 5 6 7 8
R99 U10D
12
+
14 VB
47K 13
-
Q4 VCC R98 C49 LF347 C48 C52
F1 D8 MJE520 47K 2.2uF .1uF 100uF
VCC
1 AMP
D10 D9 R97 +5
TB1 1K C46 R116 U14B
A 1 220uF 5 A
+
D11 7 Q10
2 10K 6 2N2222
-
R119 R115
3 1K 10K LF347 Q11 +10
D7 U14A 2N2222
C47 C45 1N4746 2 - C57
1000uF 220uF R118 1 Q8 100uF R121 R111
3 + 2N2907
2
15 16 +10 SOLDER JUMPER
SID OUT +5
17 18
LATI 8 U9B
19 20
SID IN AUX R62 U10B
21 22 6 4066
SPEAKER LO -
23 24 7 11 10 RX AUDIO
25 26 5
27K +
CON26A
LF347
VB
12
CONTROL 1
SW1
1 16 C43 R86 C44
INSTALL JU1 ENCODER INPUT
C32 & JU3 FOR
HALF DUPLEX 180pF 27K .1uF
4.7uF 100V (1 PAIR)
L4 U11A
RED U10C R85
JU1 4066 R88 - 9 CONTROL TONES
150uH 1 2 8
C V4 + 10 VB 62K C
C67 ERZ-C05DK330 1 T1 8
SOLDER JUMPER 620
.01 LF347
R61 R61 INSTALLED
620 FOR -FD OR -4W R63
13
4 5 R87 250K POT R84
V2
ERZ-C05DK330 CONTROL 3 3 1 TX AUDIO
C65 600:600 JU3
L2 .01 C33 620 18K
J3 GREEN
2
2
SOLDER JUMPER
1 150uH MOD OUT
4.7uF 100V
4
3 JU2
6 4.7uF 100V SOLDER JUMPER R76
1
5 L3 C34 BALANCE
BLACK INSTALL FOR ADJUST VCC VDD
MOD JACK FULL DUPLEX R81 2
150uH VB (2PAIR) 25K POT
BOTTOM V3
ENTRY C66 ERZ-C05DK330 1 T2 8 10K
.01 R82
U10A
3
- 2 GND VSS VEE
D
V1 4 5 1 1K D
ERZ-C05DK330 600:600 + 3 R83 APC DA1561
C64
L1 .01 C35 LF347 CPI COMMUNICATIONS, INC.
YELLOW 150K 1(972)437-5320 1(800)869-9128
Title
150uH 4.7uF 100V C51 |LINK TR SERIES TONE REMOTES
2.2uF |SHEET2.SCH
|SHEET3.SCH Size Document Number Rev
|SHEET4.SCH B C
VB
Date: Friday, January 03, 1997 Sheet 1 of 4
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
R112
+10 +7.5
100K X 9
39K +10
RN1C R100 R101
1
VCC VDD GND VSS VEE +10 +5
U16
C53
T L 7757 100K 100K
R107 .1uF 1 2
RST +V
MONITOR SWITCH
GND
U15B
10
4
A 6 A
120K -
C55 7 CONTROL 1
.01uF 5
28
3
+
2
U17
+5 L M 324
VDD
MCLR
22 U15A
RC4 12 2
S1 -
SHOWN OFF-HOOK 23 RB2 1
+5 CONTROL 2
RC5 13 3 +
24 RB3
HOOK SWITCH
RC6 14 L M 324
25 RB4
RC7 10
R108
18 RB0
PTT
RC0 11 U15D
19 RB1 13
120K -
C56 RC1 14 CONTROL 3
.01uF 20
RC2 6
SW7 12 +
CLKOUT
R123 1 U14D
RTCC 13
F2 LED Q6 4
OSC
+10
-
4 14
VSS 12
1K +
1
2N2907 R122
2 +10 LF347
27
26
Y1
JU7 47K
5
SOLDER JUMPER 4.0MHZ
C61
R125 JU9 20pF R95 3 4
F1 LED Q7 +10 U12
SOLDER JUMPER
1
R113
120K C62 U11C
1K 10K R91
12
VCC
VSS
2N2907 R124 2 4066 17.4K
+5 SCK
C54 R106 U13C
C 20pF 3 6 9 - C
JU8 SID VOUT 8 10 11
47K
4 .033uF 10K 10
VDD
+
CLK
R128 LATI
4.7K U11B
SOLDER JUMPER LF347
M L 2 035 VB 4066
F1/F2 SWITCH
7
R93
R104 C63
+10
240.0K
10K R103 D12 10pF +5
SCK 8 9
Q5 2N2907 10K 1N4148
SID OUT
PTT LED
R102
LATI
SW8 R94
VB
U13D
1K AUX PTT LED SID IN R92 - 13 7.32K
14
U13A + 12
- 2 R109 3.3K
CONTROL 4 1 LF347
D + 3 +7.5
D
3
100K
LF347 R80
U13B R110 10K POT CPI COMMUNICATIONS, INC.
- 6 2 1(972)437-5320 1(800)869-9128
U14C CONTROL TONES 7 TONE LEVEL Title
10 + 5 47K TR SERIES
+
CONTROL 5 8
9 LF347 Size Document Number Rev
1
- +7.5
VB B C
LF347 VB
Date: Friday, January 03, 1997 Sheet 2 of 4
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
C8
470pF
REMOVE FOR INCREASED RX AUDIO
PANEL/BOOM MIC GAIN R10
R34
R33
JU6 R47 100K
100K
R37 C9 C7 R9 U2B 1.2K
560K 6 - R35 U2C
SOLDER JUMPER
7 9 - C24 C22 C23 U2D
10K .47uF .1uF 10K 5 + 8 12
+
C42 10K 10 + 14 COMPRESSOR OUT
LF347 .033uF .033uF .033uF 13
-
VB LF347
A A
47pF VB R32 LF347
1K R30
6.8K R31
220K
4
R74
CONTROL 5 U9C
4066
1M CONTROL 3 5 R36 C5 VB VB
6
1K 1uF
C41 R70 VB U7B U2A D1
PANEL/BOOM MIC 5 R126 R7 3
+ +
7 9 8 1
.01uF 3.9K 6 2 1N4148
3
- -
18K Q2 1K
U6D 2N2222
R69 LF347 LF347 R8 D2
10K 4066 1.8M C6 1N4148
SW3 R75 1uF
SW2
1
3 14
MIC LEVEL
R40 R68 R66 R49
DESK MIC BIAS VB 2 15 2 VB
3.9K 100 68K 1K
C36 R64
R67 SW4 4 13
5K POT
R18
3
100uF 5.1K FD PATH
68K VB
U6A 10.0K
C40 R65 VB U7A
HANDSET/DESK MIC HI 3 R127 4066
+
1 1 2
2
.1uF 27K 2 C25 R13
-
18K 3 1
LF347
2.2nF 6.81K
CONTROL 2 R39
13
R11 R12 C10 1K POT R16
B CONTROL 4 C11 44.2K B
.01uF 1%
3
10K 10.0K .01uF 1% U3C R19
6
R38 U3B R15 - 9
U3D 1K POT U3A R14 - 6 8
NOTE: U6 IS REMOVED TX AUDIO 9 8 14
- 13 2
1
- 2 7
+ 5 7.32K
+ 10 44.2K
1
4066 VB
VB VB
INSTALL FOR R17
FULL DUPLEX
(2 PAIRS)
10.0K
1
U9A C39
SOLDER JUMPER
4066 BEEP INPUT
CONTROL 1 13
JU4 .1uF
VCC
VB
R78 R72
2
R43 10K
2.7 R96
3
U6B 18K
R79 EARPIECE
R77 ADJUST 4066 R71 U7C
10K 2 11 10 9 - R73 C38
C28 10K 8 EARPIECE
220uF 100K 10 +
U5 U7D 25K POT 100 22uF
13 LF347 C37
14
1
-
L M 3 80 14 VB .1uF
12
2 VB 12 +
C + C
SPEAKER HI 8 AUX INPUT 2
6 LF347 CONTROL 4
-
C16
.01uF C14
1
7
.1uF VB
R44
2.7
SW6
C17 R20 R42 6 11 +5
4.7uF 100K 100K J1
VOL HI
1
2
U6C AUX PTT LED
3
AUX INPUT 2
4066 4
C15 R23 VOL HI
VCC 4 3 5
VOL WPR BEEP INPUT
6
COMPRESSOR OUT
C27 7
.01uF 100K VCC
.1uF R21 8
R41 22K R22 9
2.7 10
10
5
CON10
R45 D6
2N2907 CONTROL 5
C12
220uF Q3 10K 1N4148
U4
R46
14
L M 3 80
C26 2 VOL LO
+
SPEAKER LO 8 10K
6
-
220uF NP
5
D5
1
7
D 1N4148 R90 D
220 SW5
C13
4.7uF
12
VB VCC VDD
CPI COMMUNICATIONS, INC.
1(972)437-5320 1(800)869-9128
Title
CONTROL 1 TR SERIES
C4
470pF
A A
R4
R28
R25
100K
100K
R6 C1 C3 R3 U1B 1.2K
FD PATH 6 - R5 U1C
7 9 - C20 C19 C18 U1D
10K .47uF .1uF 10K 5 + 8 12
+
10K 10 + 14
LF347 .033uF .033uF .033uF 13
-
VB LF347
VB R29 LF347
1K R27
6.8K R26
220K
R2
1K C21
U1A D3 1uF VB VB
R24 3
+
1
B
2 1N4148 B
-
Q1 1K R1 D4
2N2222 LF347 1.8M C2 1N4148
1uF
VB
R53
10.0K
2
C31 R50
3 1
2.2nF 6.81K
R52
R59 R56 C30 1K POT R58
C29 44.2K
.01uF 1%
3
10K 10.0K .01uF 1% U8C R51
U11D U8D R57 - 9
C U8B R54 U8A R55 - 13 8 C
4066 - 6 2 - 2 14 + 10 44.2K
8 9 7 1K POT 1 12
TX AUDIO + 7.32K
+ 5 + 3 10.0K LF347
LF347 VB
LF347 LF347
1
VB
6
VB VB
CONTROL 2
R60
10.0K
VCC VDD
+5
J1
J2
2 1
DESK MIC BIAS
1 2
HANDSET/DESK MIC HI AUX PTT LED
4 3
PTT AUX INPUT 2
3 4 GND VSS VEE
EARPIECE VOL HI
D 6 5 D
BEEP INPUT
5 6
MONITOR SWITCH COMPRESSOR OUT
7
MODJACK 6
VCC 8 CPI COMMUNICATIONS, INC.
9 1(972)437-5320 1(800)869-9128
BOTTOM VIEW 10 Title
CON10 TR SERIES
ROW 4
U1 PIC16F747
VDD VDD ROW 3
F1 15 2 AN0 GUARD TONE
RC0 AN0 ROW 2
F2 16 3 R48 R52
RC1 AN1 AN1 FUNCTION TONE
ROW 1
F3 17 4 100K 100K
RC2 AN2 AN2 HOLD TONE
R69 4.7K
F4 SCK LED Q11
D 18 RC3/SCL RC6/CK 25 D
F5 23 26 SID OUT
RC4/SDA RC7/DT COLUMN 1 COLUMN 2 COLUMN 3 COLUMN 4 PN2222A
F6 24 5
RC5 RA3 AN3 PTT, MON, INT, PRIV, SEL ALL - SW
+5V
F7 CS F4 R33 470
8 RE0 RA4 6
OSC2
S5 S6 S7 S8
COLUMN 4 R30 3.3K ROW 1
36 RB3 RB4 37
14
A A
7 6 F4 L1 150uH
VCC
WP SCL
F5 VDD +10V CPI COMMUNICATIONS INC.
1 A0 SDA 5
R62 R55 2 Title
4.7K 4.7K 3
A1
A2 VSS 4 R49 470 C5 C6 C7 TR-16F FRONT PANEL
10uF .1uF 10uF Size Document Number Rev
CS +5V +5V U2 24LC04B/P +5V
+5V +5V 700-TRML-200 B
Date: Thursday, October 09, 2008 Sheet 1 of 3
5 4 3 2 1
5 4 3 2 1
X1 D29 R47
WM54BT LINE 1 ACTIVITY
J1 +5V
VOL HI VOL WPR FRONT PANEL MIC
VOL LO 1 2 PANEL/BOOM MIC LINE 1 1K
SPEAKER HI 3 4 PTT LED
JP1 MONITOR SWITCH 5 6 PTT
PTT INTERCOM SWITCH 7 8 CS
5 LINE 1 ACTIVITY 9 10 SELECTED AUDIO IN
D D
4 ENCODER INPUT 11 12 D24 R27
3 13 14 VCC
SCK LINE 2 ACTIVITY
2 15 16 +10V +5V
SID OUT
1 LINE 2 ACTIVITY 17 18 OFF HOOK DISABLE +5V
SID IN 19 20 HOOK IN FOR NO OFF LINE 2 1K
ENCODER SPEAKER LO 21 22 LINE 3 ACTIVITY JU2
23 24 HOOK
LINE 4 ACTIVITY MONITOR
25 26
JU3 JU4 CON26A +5V D12 R17
LINE 3 ACTIVITY
+5V
+9V VCC
ENCODER POWER LINE 3 1K
VDD HK TR
3
Q3 R7 R5 2 Q2
INTERCOM 2N7000 10K 10K
TO-92 1 P0111DA
2 TO-92
R4 10K
D35
1
D22 R21 R53 NOT USED PRIVACY LED
PTT +5V D4 D16
1N4148 1N4148
22.1K 4.22K D7
1N4148 1N4148
PTT LED R10 F14 F15 +5V
MONITOR SWITCH
VDD
A D11 A
1K
PTT LED PTT
MONITOR LED MONITOR
CPI COMMUNICATIONS INC.
Title
D23 TR-16F FRONT PANEL
Size Document Number Rev
+5V 700-TRML-200 B
Date: Wednesday, October 29, 2008 Sheet 2 of 3
5 4 3 2 1
5 4 3 2 1
SELECTED_AUDIO_VOLUME VB
WHT VOL HI
1uF
1
+5V
R76
THIS PART IS GRN VOL WPR
11
2
D 1K D
LOCATED - 2
OFF-BOARD. R79 C9
1
+10V 10K POT VB + 3 SELECTED AUDIO IN
VIO VOL LO MCP6004 I/P
3
Q8 100K
U4A .01uF
4
PN2907A
R68 LS1 +10V
470 R75
THIS PART IS SPEAKER 2.7K
R74
VB LOCATED Q12
1
OFF-BOARD. 3 27K
2
C11 ORG BLK C10
C12 R91 R82 PN4393
.1uF 10uF SPEAKER HI SPEAKER LO
470 100K 1uF Tant
C C
VB VB
+5V +5V +5V
FUNCTION TONE R65
AN1
2.2K
C18 180pF
R73 R84 HOLD TONE R66 R83 R81
AN2 AN0 VB
10K R85 100K 2.2K GUARD TONE 1.5nF 5% COG .1" LS
2.2K 48.7K 2.32K
U3D C19
13 - 470pF
C15 MCP6004 I/P R80
14
R89
VB 12 +
+ 5
MCP6004 I/P VB - 9 7
8 - 6
+ 10 U4B 48.7K
B 1.5nF 5% COG .1" LS MCP6004 I/P 48.7K B
R71
R90
U4C VB
5.23K
3
C20 5.23K
1
9 - 2 1.5nF 5% COG .1" LS 1K MULTITURN POT
8
10 + BI TECHNOLOGIES R87 2
MCP6004 I/P 67YR1K
VB C21 BI TECHNOLOGIES
1
R88
67YR1K
1.5nF 5% COG .1" LS +5V R86
R57 13 -
3
14
5.23K
11
12 +
C1 48.7K MCP6004 I/P
U3A - 2 VB 5.23K
R72 U3B R58 U4D
- 6 1
7 R59
+ 3
+ 5 MCP6004 I/P
A
48.7K 48.7K 20.0K A
MCP6004 I/P
4
VB
+10V
CPI COMMUNICATIONS INC.
R61 R60 Title
VB TR-16F FRONT PANEL
200.0K 2.32K Size Document Number Rev
700-TRML-200 B
Date: Wednesday, October 29, 2008 Sheet 3 of 3
5 4 3 2 1
900-TRBB-100 PARTS LIST 2 wire board only
1 700-TRBB-200 PCB
Full Duplex option parts list for TR10-16F-FD
3 242-0001-102 1K R2,24,29
4 242-0001-103 10K R3,5,6,59
2 242-0001-104 100K R4,28
1 242-0001-122 1.2K R25
1 242-0001-185 1.8 MEG R1
1 242-0001-224 220K R26
1 242-0001-621 620 OHM R61
1 242-0001-682 6.8K R27
45
1 256-0001-040 40 PIN IC SOCKET U1
1 700-TRML-200 PCB
46
Misc parts
47