Professional Documents
Culture Documents
Mantainence Manual
Mantainence Manual
[17815; 15.06.2011]
Summary This manual provides detailed instructions for maintaining the OLEO buffer.
Page 1/9
Table of Contents
1 Safety Advice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2 * Preventive Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.2 * Preventive Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 4
3 Buffer Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4 Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.1 Replace Entire Component . . . . . . . . . . . . . . . . . . . . . . . . 8
4.2 Replace Safety Switch . . . . . . . . . . . . . . . . . . . . . . . . . . 8
A1 * Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
OLEO Buffer
K 602848 06
Maintenance
Copyright © 2012 INVENTIO AG 2/9
1 Safety Advice
OLEO Buffer
K 602848 06
Maintenance
Copyright © 2012 INVENTIO AG 3/9
2 * Preventive Maintenance
2.1 Overview
Task List
Interval Description Details
[M = Month] Given In
12 M General check of buffers 1) Section 2.2
12 M Clean buffer 1) Section 2.2
12 M Check oil level 1) Section 2.2
12 M Check height of buffers 1) Section 2.2
12 M Check safety switch 1) Section 2.2
1) These tasks must be completed after a buffer impact.
General Check
No Step
1 Check the buffer and its horizontal support (if available) for any damage.
2 Check that the buffer stands vertically in the hoistway.
Clean
1 Clean the buffer casing.
2 Clean the plunger and oil lightly.
A A
2
B B
1 3
HP
a) b)
Points of Maintenance (buffer type LB shown) [17802; 08.06.2011]
1 Oil filler screw a) Buffer standard version
2 Dipstick b) Buffer pre-filled with oil
3 Safety switch
OLEO Buffer
K 602848 06
Maintenance
Copyright © 2012 INVENTIO AG 4/9
Refill Oil
1 Unscrew the oil filler screw (1) and refill with the quantity of oil needed. The
maximum oil level must not be exceeded. For the oil type, refer to the note below.
2 Check the oil level using the dipstick (2).
Use HLP 68/ISO 6743/4 L-HM68, in accordance with DIN 51524. These are mineral oils
with additives for improvement of anti-corrosion properties, anti-aging and improved
performance under boundary lubrication conditions (anti-seize additives).
Check Buffer
1 Check the HP dimension against the following table when the buffer is fully
Height
extended.
2 If the dimension HP is in accordance with the value in the following table, the
buffer is ready for operation. If not, the unit must be replaced.
HPH
HP
Height of Buffer (Drawing with SEB type) [17801; 08.06.2011]
OLEO Buffer
K 602848 06
Maintenance
Copyright © 2012 INVENTIO AG 5/9
Type HPH [mm] 1) HP [mm] Oil [l]
LB32.002 699 1702 (-5, +5) 20.00
LB35.001 881 2104 (-5, +5) 24.50
LB40.001 1141 2689 (-5, +5) 31.50
LB50.001 1740 4208 (-9, +8) 27.80
LB55.001 2109 5031 (-9, +8) 33.30
LB60.001 2504 6173 (-9, +8) 73.50
1) Minimum value
Check Safety
Switch 1 Check that the safety switch (3) KP operates smoothly and works correctly.
OLEO Buffer
K 602848 06
Maintenance
Copyright © 2012 INVENTIO AG 6/9
3 Buffer Test
Buffer tests must be carried out periodically according to the local regulations.
After the buffer tests have been carried out, check the height HP according to the table
above.
If the top position height is no longer reached, or if leaks are found, the buffer must be
replaced.
OLEO Buffer
K 602848 06
Maintenance
Copyright © 2012 INVENTIO AG 7/9
4 Replacement
Procedure
No Step
1 Remove old buffer and drain oil from buffer.
2 Install new buffer according to the installation procedure.
Related
Document Title
Documents
K 602846 Technical Information and Configuration OLEO Buffer
K 602847 Installation OLEO Buffer
EJ 604722 SAIS Supporting Info Buffer
EJ 41348298 SAIS Information Buffer NA
Procedure
No Step
1 Remove wiring from terminals and remove old safety switch.
2 Install new safety switch at same position.
3 Connect wires to terminal of new safety switch.
4 Check function of new safety switch.
OLEO Buffer
K 602848 06
Maintenance
Copyright © 2012 INVENTIO AG 8/9
A1 * Spare Parts
Spare Parts
Pos. Image Description Stock Quantity ID. No.
Part 1)
1 - Oil DIN51524 - HLP68 Y - 293150
2 Switch for LSB Series,
MLB13.1 ... MLB32.1, SEB Series:
IP67
N 1 59373267
with roller plunger
Impulse, 1 NC / 1 NO
with gland
Switch for LSB Series,
MLB13.1 ... MLB32.1, SEB Series:
IP67
N 1 59373268
with roller plunger
Impulse, 1 NC / 1 NO
with adaptor
Switch for MLB35.3 ... MLB40.3,
LB16.003 ... LB40.001:
IP67
N 1 59373394
with angle roller lever
Impulse, 1 NC / 1 NO
with gland
Switch for MLB35.3 ... MLB40.3,
LB16.003 ... LB40.001:
IP67
N 1 59373395
with angle roller lever
Impulse, 1 NC / 1 NO
with adaptor
Switch for LB50.001 ... LB60.001:
IP67
with plunger N 1 59373392
Impulse, 1 NC / 1 NO
with gland
Switch for LB50.001 ... LB60.001:
IP67
with plunger N 1 59373393
Impulse, 1 NC / 1 NO
with adaptor
Switch EX for SEB Series:
Ex-proof
with roller plunger N 1 207942
Impulse, 1 NC / 1 NO
with cable
Switch EX for LB Series:
Ex-proof
with roller plunger N 1 217290
Impulse, 1 NC / 1 NO
with cable
1) Y = Must be available in given quantity in local stock at all times; O = Optional in local stock
and N = No stocked part.
OLEO Buffer
K 602848 06
Maintenance
Copyright © 2012 INVENTIO AG 9/9