Professional Documents
Culture Documents
Awash Joint Material Approval Shedule 1
Awash Joint Material Approval Shedule 1
PLC
Location: Bale Robe Branch Contractor : Tilahun Abebe G.C
Material that Material that
must be approved can be
Item No Description by MTT and approved by Remark
Awash Bank MTT only
B. SUPER STRUCTURE
3.02 Flashing with G 28 flat metal sheet with dev. Length of 50cm
3.03 Copping with G 28 flat metal sheet with dev. Length of 50cm
CEILING WORK
Supply and install Acoustic ceiling tiles or equivalent with square edge
4.01 Pelican Econogrid pre-painted white exposed tee grid system including fire
safety punch outs. Main tees suspended by means of 19 x 0.5mm GMS strap (or
2.5 wires) hangers at 1200mm centres and all the neccessary accosories to
complete the work as per the manufacturer details.
Supply and install of Patterned PVC laminated gypsum board ceiling tiles, with
4.02 aluminum foil on back face for water resistance, with prepainted galvanized
ceiling grids and accessories, including cross, main runner, and wall angle,
suspended by expansion bolt and galvanized wire and all the neccessary
accosories to copmlete the workas per the manufacturer details..
Note: wood works include painting, varnishing, polishing, oiling & the like.
Supply and fix fire rated Emergency Stairways door constructed from
Galvanized Steel with 25mm halit fire proof insulated fill, 3mm fire proof
4.03 veneer layer and finished with insturmescent strip seal with fiber mesh pannel
with resistance time 30min.Price includes all assistance works and accessary
needed to complete the work.
D6 Size = 900 x 2100 mm
Supply and fix hand rail for stair case in Ø40mm CHS at the top, 40x 40 x
2.5mm thick vertical member every other two steps fixed to concrete stair and 3
5.04
x 25 x25 x 2.5mm thick horizontal rail member. All works shall be executed
including plate and bolt based on the detailed drawings . Price shall include
paint and all the necessary works needed to complete the work. Colors and all
works there to are subject to the approval of the Engineer.
Supply and fix fully glaized aluminum partition wall including door opening, as
per supplier's specifications and detail drawings and Engineer's approval. The
5.05 aluminum tubular profile frame shall be approved by the Engineer. Price
includes Italian type approved lock, hinges, 5mm thick clear glass and other
hardware and iron mongery. "
Supply and Fix Aluminium Sky light made of Structural frame and heat proof
5.06 double structural glazing with water proof joints. Detail for all electrical
appliances and fixing should follow the manufacturers instruction and as per
the detail drawing. Price includes all the necessary accessories required. "
Supply and Fix Aluminium Luvers made of 2mm thick Aluminium frames as per
5.07 the detail drawing. Unit price shall inlude all accessories and connecting pieces
to complete the work. "
B. Metal Works
Supply and fix in position metal Window, door and partition wall made with
5.08 38x1.5mm LTZ steel profile. Price includes best quality cylindrical lock, kicking Approved by Consultant but
plate, hinges, one coat of anti-rust and two coats of synthetic paint., 4mm clear test report and material
glass and all necessary accessories to complete the workas. All work shall be in specification shall be
accorance with the Architectural detail drawing and approval. attached for all metal works.
A - Doors
D5 size 1800 x 2100 mm
5.09 Supply, assemble & erect steel structure in accordance with structural drawing.
Price includes one coat of anti-rust & two coats of synthetic enamel paint. "
5.09.1 RHS truss "
a) upper & lower chord, diagonal and vertical member "
size 50x50x3mm
size 40x40x3mm
Supply and fix corner protection on exposed RC exposed column edges, made
5.10 specifically for this purpose with metal sheet with mim. thickness of 1.2mm,
centrally bent for corner and the side flanges are perforated as mesh to be
imbedded in cement mortar (1:3) plaster up to a hight of 2 meters and to be
further finished. The sample shall be approved before installation. "
Sundry Item
(Provisional Item)
Supply and fix Vault Room windows and doors. Price shall include all the
5.11 necessary works needed to complete the works
Windodw size 700 * 700mm
Door size 1000 * 2100mm "
Page 1 of 19
Client: Awash Bank Conusltant : MTT Consulting Architects and Engineers
PLC
Location: Bale Robe Branch Contractor : Tilahun Abebe G.C
Material that Material that
must be approved can be
Item No Description by MTT and approved by Remark
Awash Bank MTT only
It can be approved by
consultant but samples,
6.1 Supply and lay polished, chamfered & epoxy treated or equivalent type Marble catalogues and/or
tile.The price shall include Mapei, Cercol, Keracol or equivalent filler and brochures shall be
adhesive presented.
h) For Throated, weathered, champhered & grooved Marble copping
size ( 27 x 3)cm. "
i) For Throated, weathered, champhered & grooved Marble copping
size ( 25 x 3)cm. "
Supply and fix approved quality Polished Porcelain skirting on plastered wall
6.12 by means of Max Fix or equivalent cement adhesive .Price shall include cement
sand mortar (1:3) ratio backing, The skirting shall be champhered top one
edge. Size 10 x 1cm "
6.14 Supply and fix approved quality RAK or Equvalent Ceramic skirting stuck to
wall with cement -sand mortar ratio1:3 on to wall surface for Ceramic floor. "
6.17 Supply and fix approved imported 3mm thick plastic floor tile colour, pattern
and special adhesive glue shall be approved by the engineer.
Supply and fix 10cm high PVC skirting. Price shall include all the necessary
6.18 works needed to complete
the work. "
Supply and fix high quality pressurized laminated board (HPL) partition wall
should be completely moisture proof, highly scratch-and-impact-resistant,
6.19 colorfast, chemical resistant easy to clean and should not require any special
maintenance. Colors and all works are subject to the approval of the
Engineer. "
Supply and fix 100mm thick gypsum board partition wall including door
It can be approved by
opening, as per supplier's specifications and detail drawings and Engineer's
consultant but samples,
6.20 approval. The board has to be high bond strength, water proof and fire catalogues and/or
resistant a minimum of 3 hours.
brochures shall be
" presented.
Supply and fix approved quality 200x300x8mm RAK or Equvalent Ceramic wall
6.21 tiles Price shall include cement sand mortar (1:3) ratio backing, adhesive with
Max Fix or equivalent & grouting with water proof joint filler.The consultant
must approve the size, pattern,color & texture of the tiles.
Supply and fix approved quality 300x60010mm Granite wall tile lay over the
6.22 pre finished plastered surface .work & cost includes Max Fix or equivalent
cement adhesive & water proof joint filler or equivalent. Pattern, colour &
cement adhesive shall be approved by engineer. (for lift wall) "
6.23.1 Supply and lay approved type 45x45x3.8cm colored concrete paving tile laid on
well compacted and levelled 10cm thick red ash with 2% slope to the open ditch
and finally pointed with cement mortar (1:4) around the building
7.0. Painting
8. SANITERY INSTALLATION
All fixtures which differs from that specified below is subject to the Engineer's
approval, based on samples, catalogues and brochures presented by the
Contractor. Unit Price shall include all the necessary fixing brackets or hooks
and all the necessary assistance civil works such as chiseling of walls,floors,
beams and etc…
Supply and fix golden dragon or Equivalent, above counter hand wash basins
made of white glazed vitreious china as per BS3402 Standard. The price
includes REMER/JAQUAR or Equivalent chrome plated cold and hot water tap,
granite base stand with RHS horizontal support as shown in the
drawing,complete with mixing battery plug, chrome plated chain holder, P-
smell trap with connection pipe, fittings, all other necessary fittings etc.
complete in all respects.accessories. Flexible hose to be REMER or Equivalent
to be Vinyle coated and should be capable of resisting pressure of 4 bar. P-
smell trap should be brass chrome plated with 50mm height of water seal and
8.1.1 trap.
Size :- 570 x 470 x 185 mm
Page 2 of 19
Client: Awash Bank Conusltant : MTT Consulting Architects and Engineers
PLC
Location: Bale Robe Branch Contractor : Tilahun Abebe G.C
Material that Material that
must be approved can be
Item No Description by MTT and approved by Remark
Awash Bank MTT only
Supply and fix olden dragon or Equivalent, white glazed vitreous china as per
BS3402 Standard floor mounting type (European style) P/S trap water closet
with solid white plastic seat and lid, chrome plated brass hinges and rubber
buffers with white vitreous china 3/6 dual flush coupled cistern including
required fittings, accessories etc. complete in all respects. Flexible hose to be
REMER/JAQUAR or Equivalent to be Vinyle coated and should be capable of
8.1.2 resisting pressure of 4 bar. "
Supply and fix PHELEXICARE or Equivalent Vanity type hand wash basin unit
designed to assist disabled people and those with limited reach. The vanity top
8.1.3 is to be designed with the bowl area as close as possible to the user. "
Vanity Top
The Vaity top is to be made from water-resistant granite topping. The front
apron to have a depth of only 100mm to allow for free access for knees. "
Vanity Top size :535 x 700mm
Basin
hand wash basin to be white vitreous china with apron front of 100mmand can
be fitted to the right side of the vanity. "
Basin size :510 x 455mm
Fixing Brackets
Fitted to the underside of the basin with toggle bolts and screwed to the
undeside of the work top
Accessories
Tap has to be provided separetly for cold and hot water, model should be
REMER/JAQUAR or Equivalent chrome plated cold and hot water tap,
Complete with mixing battery plug, chrome plated chain holder, P-smell trap
with connection pipe and with all other hose to be REMER/JAQUAR or
Equivalent, necessary accessories. Flexible hose of Length 60cm to be Vinyle
coated and should be capable of resisting pressure of 4 bar. P-smell trap should
be brass chrome plated with 50mm height of water seal and trap. Colour of the
topping to be decided by the Architect. Granite "
Supply and fix R.A.K. or Equivalent white glazed vitreous china wall mounting
type toilet paper holder with chrome plated fastening screws and other
8.1.4 accessories. "
Supply and fix 6mm thick crystal glass mirrors for hand wash basins with
copper back protection, including chrome plated brass mirror frames with
8.1.5 chrome plated screws and etc... for hand wash basins.
Size :- 600 x 500 mm
Supply and install urinals made of acrylic, unit price shall include all
8.1.6 accessories neccessary for complete installation.
Size: 457x653x659 mm
Supply and fix TEKA or Equivalent, 1.2mm GRADE 304 approved standard
stainless steel kitchen sink of Double bowl complete with chrome plated
REMER/JAQUAR or Equivalent cold and hot water mixing battery (chrome
plated faucet), plastic Bell type smell trap, plug, chain holder, drain pipe,
mixing faucet, etc; and all other accessories.Flexible hose to be
REMER/JAQUAR or Equivalent to be Vinyle coated and should be capable of
8.1.7 resisting pressure of 4 bar.
Size: 1500 x 600 mm
supply and fix super aqua or equivalent water heater including all assstance
8.1.8 fittings and civil works.
capacity : 80 Lit
Supply and fix NAFFCO or equivalent recessed wall mounted fire hydrant hose
reels as per BS EN671-1. Complete with dia. 40 mm and 25 meters necessary
accessories. Cabinet shall be factory made 1.2mm thick pretreated electro
galvanized steel sheet, painted with electrostatic powder coating and oven
backed at min.180 degree cent with easily openable glass door of size shall
beabout 900 x 600 x 250mm /approximate.size/. Price shall include angle
valve,pressure reducer & fire extinguisher 6kg weight ABC Chemical powder in
8.1.9 side cabinet.
Fire hydrant water supply pipes shall be medium gauge galvanized steel and be
fixed to slabs, walls,beams or etc…with metal straps or similar material. Unit
price shall include all assistance civil works and necessary fittings such as T,
instruction and according to where shown on the drawing. All water pipes
shall be tested two times the working pressure or 50 meters head, which ever is
8.1.10 greater at the expense of the contractor.
Dia. 40 mm
Dia. 50 mm
Dia. 65 mm
Supply and fix floor drains made of uPVC circular box of approved quality for
grey water with 4- side openings, complete with P-smell trap, treaded
drain/clean bottom outlet, approved standard plastic or stainless steel cover
8.1.11 and all other necessary fittings and accessories
Size:- Dia. 75/75/75/110 mm
Supply and fix approved quality floor clean outs as where shown on the
8.1.12 drawing. Price shall include all the necessary connecting pieces.
Compatible with Dia. 110 mm
supply and installs complete fountain system including recirculation pumps and
assocated pipe works and fittings in the ground floor as shown in the layout and
section detail design drawing. Price shall include all assicistance civil works
8.1.13 including specified finishing metrials and water proofing works.
supply and install water taps and necessary fittings for prayer zones of the
8.1.14 building as shown in the building design sanitary drawing.
Page 3 of 19
Client: Awash Bank Conusltant : MTT Consulting Architects and Engineers
PLC
Location: Bale Robe Branch Contractor : Tilahun Abebe G.C
Material that Material that
must be approved can be
Item No Description by MTT and approved by Remark
Awash Bank MTT only
Page 4 of 19
Client: Awash Bank Conusltant : MTT Consulting Architects and Engineers
PLC
Location: Bale Robe Branch Contractor : Tilahun Abebe G.C
Material that Material that
must be approved can be
Item No Description by MTT and approved by Remark
Awash Bank MTT only
It can be approved by
Supply and install Polypropylene Random Co-polymer resins (PP Type 3 raw consultant but samples,
material) PPR PN-20 to internal cold water distribution system as shown on the catalogues and/or
drawing. Complete with all the necessary fittings and accessories. All diameters brochures shall be
8.2.1 specified here are internal (Nominal) diameters. presented.
Dia. 20 mm
Dia. 25 mm
Dia. 32 mm
Dia. 40 mm
Dia. 50 mm
Supply and fix 15mm dia chrome plated brass quarter turn angle valves with
chrome plated copper connecting pipe, union nut and chrome plated brass wall
flanges, and accessories complete in all respects. The Angle valve should be
capable resisting of PN-10 before hand wash basins, water closets and other
8.2.2 fixtures. "
Supply and fix PPR service valves of approved standard, capable of resisting
PN-10 on internal branch and pipe inlet to toilet, kitchen, bath room,etc; of the
following size and as where shown on the drawing. The gate valves should be
compatible with PPR pipe on internal and external branch pipes, at inlet points
8.2.3 to the building, "
Dia. 25 mm
Dia. 32 mm
Dia. 50 mm
All domestic waste, vent and storm water pipe linesshall be comply to BS 459,
BS 4660, BS 5481, DIN 8062 as appropriate, using double ring seals and
gaskets complying with BS 2394 uPVC, PN-6 pipesand shall be provided with a
minimum slope asstated in the drawing. Pipes and necessary fittings shall be
standard quality and be free from damage during storage, construction and etc.
Unit price shall include all the necessary assistance civil works, suchas
excavation cartaway, fixing or hanging to walls,beams or slabs. etc., necessary
fittings such asbends, Y, etc. Storm water uPVC, PN-6 pipes shall resist the
external temperature and the quality shallmeet the purpose.
Flushing and testing of waste water system.Flushing has to be done to clean the
pipe line fromdebris and silts. All waste water Pipe shall betested by water
pressure of 1.5 meters head for minimum of Two Hours.
Providing, laying and jointing of internal uPVC PN-6 waste pipes with all
uPVC pipe fittings including jointing with solvent cement joints and testing of
joints etc. according to where shown on the drawings. Complete with all the
necessary fittings. Provide cleaning detail for all waste water riser pipes as per
8.3.1 the detail drawing.
Dia. 50 mm, Outer diameter
Dia. 75 mm, Outer diameter
Dia. 125 mm, Outer diameter
Dia. 160 mm, Outer diameter
8.3.2 Vent caps made of uPVC, PN-6 complete with all accessories. "
Dia. 75 mm
Dia. 110mm, for septic tank
8.5 Pumps
8.5.1 Domestic Pumps(cold water)
Supply, fix ,test and commission groundfoss or Equivalent approved quality
Electric driven booster centrifugal domestic water pump with Cast iron
impeller, as per the manufacturer's instruction, technical specification and
drawing shown. Price shall include:
20 cm thick double reinforced with dia. 12/100 mm reinforced concrete seat "
Bronze gate valve on suction pipe, Diam. 65 mm "
Dual plate WAFER type cast iron non - return valve "
Diam. 50mm of Approved standard rated to PN-20, with bolts, nuts, 3mm thick
gasket and matching flanges. "
Water level indicator for low and high water level in the water storage for
pumps including float type probes, wiring cable, conduit and making
connection to pump panel complete in all respects and making system
functional, cutting and making good. "
Dry running protection with cable, conduit and fixing arrangement Sensor with
panel manual and automatic change-over and sequancer suitable for the two
pumps. supply, fix, test and commission dial type pressure gauage with
isolation cork and chrome plated copper pipe. Calibration to be 0 - 10 Bar. "
Water hammer Arrestor ( Air Vessel) of 64liter capacity made of mild steel, two
coats of red enameled paint over primer outside and two coats of Epoxy coating
inside, and test pressure of 10 Bar. "
Two Pumps: ( Duty and Stand-by) "
Capacity : Discharge = 3.5 liters/second "
Total head = 35 meters "
Estimated power = 2.2 Kw "
Efficiency >70% "
NPSH >1.5m "
"
- Control Panel (IP 55) to IEE Regulations incorporating the following:
Page 5 of 19
Client: Awash Bank Conusltant : MTT Consulting Architects and Engineers
PLC
Location: Bale Robe Branch Contractor : Tilahun Abebe G.C
Material that Material that
must be approved can be
Item No Description by MTT and approved by Remark
Awash Bank MTT only
Indicators for - Power on, Pump tripped, High pressure, Low pressure, Low
water Hand (off), Lack of water and Auto selector switch for each pump
including all the necessary accessories.
Cold water pipes shall be High Density Polyethylene (HDPE), PN-10 pipes, and
be laid in trench as shown in the sanitary site drawing. Provide 100mm thick
sand bedding material rammed and tamped and 150mm thick approved material
to cover the pipe all as per the typical trench section and detail.necessary
fittings such as T, bends etc. according to where shown on the drawing. All
water pipes shall be tested two times the working pressure or 160 meters head,
which ever is greater at the expense of the contractor.
dia 20 mm "
dia 32 mm "
dia 50 mm "
dia 63 mm "
dia 75 mm "
Construct septic tank out of reinforced concrete as per the detail drawing. This is not material that
Price shall include excavation, cart away and all civil works as shown on the needs our approval,it can
8.6.2 detailed drawing . continue as usual.
Capacity 80m3
Supply and install ECOGUSS or equivalent parking drain floor gullys out of
enameled cast iron on basement car parking as shown in the design drawing.
8.7.6 Size 300x300mm "
Providing, laying and jointing of internal uPVC PN-4 subsurface drainge pipes
with all uPVC pipe fittings including jointing with solvent cement joints and
testing of joints etc. according to where shown on the drawings. Complete with
all the necessary fittings. Provide cleaning detail for all waste water riser pipes
8.7.8 as per the detail drawing. "
Dia. 75 mm, Outer diameter "
Dia. 110 mm, Outer diameter "
Page 6 of 19
Client: Awash Bank Conusltant : MTT Consulting Architects and Engineers
PLC
Location: Bale Robe Branch Contractor : Tilahun Abebe G.C
Material that Material that
must be approved can be
Item No Description by MTT and approved by Remark
Awash Bank MTT only
9. ELECTRICAL INSTALLATION
9.01.1 complete with bus bar system of 300A/3Ph+N+E and 25% reserve space. "
Flush mounted Distribution board SDB-4F with lockable door,Steel
enclosure,Earthing lead, connectors, labled and all necessary accessories
consisting of :(all circuit breakers are to be of type Legrand , ABB or approved
equivalent) "
1 pc ACB of 63A/3ph "
1 pcs ACB of 50A/3ph "
13 pcs ACB of 16A/1ph "
15 pcs ACB of 10A 1ph "
3 pcs contactors of 10A/1ph, 220V for LCP "
9.01.2 complete with bus bar system of 80A/3Ph+N+E and 25% reserve space. "
Ditto as 1.02 above but for SDB-3F,SDB-2F,SDB-1F and consisting of : "
1 pc ACB of 50A/3ph "
15 pcs ACB of 16A/1ph "
16 pcs ACB of 10A 1ph "
5pcs contactors of 10A/1ph, 220V for LCP "
9.01.3 complete with bus bar system of 63A/3Ph+N+E and 25% reserve space. "
Ditto as 1.02 above but for SDB-GF and consisting of : "
1 pc ACB of 63A 3ph "
4 pcs ACB of 25A/1ph "
10 pcs ACB of 16A/1ph "
16 pcs ACB of 10A 1ph "
9.01.4 complete with bus bar system of 50A/3Ph+N+E and 25% reserve space. "
Ditto as 1.02 above but for SDB-base and consisting of : "
1 pc ACB of 32A 3ph "
4 pcs ACB of 25A/1ph "
4 pcs ACB of 16A/1ph "
11 pcs ACB of 10A 1ph "
9.01.5 complete with bus bar system of 50A/3Ph+N+E and 25% reserve space. "
Page 7 of 19
Client: Awash Bank Conusltant : MTT Consulting Architects and Engineers
PLC
Location: Bale Robe Branch Contractor : Tilahun Abebe G.C
Material that Material that
must be approved can be
Item No Description by MTT and approved by Remark
Awash Bank MTT only
9.09 TV points
TV points fed through RG6 Coaxial 75ohm TV cable in rigid conduit of
minimum diameter 19mm of 25mm as shown on the drawing including junction
9.09.1 boxes with cover and all necessary accessories "
Supply,install connect & test TV system with all necessary accessaries complete
9.09.3 with Multichannel amplifier, Spliter,tap, Dishs and local radio ,Antenna etc. "
9.09.4 TV Splitter connection box of 150x100x70mm with cover.
CCTV SYSTEM
IP based Closed circuit television equipment, supplied, installed,connected,
tested and commissioned including CAT6A UTP cables,complete all as
specified (or equivalent).Factory test report,2 years guarantee factory faults
9.10 "
CCTV POINTS
IP CCTV points in thermoplastic conduit of minimum diameter 21mm fed by
CAT6A UTP cable as shown on drawings, including junction boxes with covers,
9.10.1 "
IP CCTV 5MP 360 deg. digital PTZ/Bi directional Audio ,Digital wide dynamic
range Motion detection Audio detection M12 & RJ-45 connector. Type
9.10.2 SAMSUNG SNF-8010VM or approved equivallent. "
Approved type 32" LCD high resolution color monitor,desplay 16/9
9.10.3 .maximum resolution:1680x1050 "
Purpose made control consol for four 32"monitors, multiplexer,controller and
9.10.4 keyboard "
9.10.5 Approved type alarming switcher 220Vac/ 50Hz "
Fully programmable keyboard controller with touch screen LCD as specified
9.10.6 or approved equivalent. "
CCTV Management Software licence for 30cameras, documentation, instruction
9.10.7 of owner's staff, power supplies/transformers. "
CCTV IP Network video recorder NVR 4/16 cameras, Pentaplex: simultaneous
live, record, playback,extraction and remote access Video compression format:
H264 , Number of frames recorded: Up to 25 frames per second for 16 cameras
in D1 resolution Memory: 2 x 2 TB internal hard disks, i.e. a total of 4TB and
built-in DVD writer: and 19" rack mountable with all necessary acessories to
make the system complete.
9.10.8 "
CCTV system with above mentioned equipments including system
connectors,line and head end video amplifiers, digital control system , cabinet
of heavy duty and free standing for all electronic equipments with complete
analysis made on cable losses (both signal and power) & signal level in dB at
out camera and monitor units ,with latest technology of each equipments, shop
drawing with complete analysis and all the necessary accessories to be
submitted prior to purchase and installtion. see the drawing for the lay out
9.10.9 "
Page 8 of 19
Client: Awash Bank Conusltant : MTT Consulting Architects and Engineers
PLC
Location: Bale Robe Branch Contractor : Tilahun Abebe G.C
Material that Material that
must be approved can be
Item No Description by MTT and approved by Remark
Awash Bank MTT only
Cabling
-As per IEC 331,IEC 332-1,IEC 332-3,IEC 1034,IEC 754-1
-With copper conductor
-Fire resistant and flame retardant
-Colour coded and suitable for addressable system
-Consisting of all the necessary accessories
Smoke / heat detector ,Manual call points , short circuit isolators , alarm and
visual indicating points fed through fire resistant cable of 2-core 2.5sq.mm
9.11.1 inside PVC conduit of 20mm diameter including all necessary accessories. "
Fire Alarm control panel with an integrated operating unit that can process
9.11.2 signals from devices of up to 150 addresses. "
9.11.3 Detector base with loop contact "
9.11.4 Manual call point "
9.11.5 Sounder "
9.11.6 Heat detector "
9.11.7 smoke detector "
CABLE TRAY
-All cable tray shall run neatly and fixed incontact with the horizontal and
vertical corner of the wall with the necessary drops and riser.
-The cable tray must consisting of accessories like clamp kit,coupling plate
,cable mounting bracket , grounding cable drop out plate ,elbows and T-joints
for horizontal,bracket,mounting box support, suspension bracketend cap,cable
retainer,hinge connector for vertical change in direction,wall and pendent
bracket for wall support ,box for cable junctions for all the necessary acessories
500mmx250mmx3000mm for PA/FA/CCTV/data cables
PVCpipes "
9.14.1 dia 110mm "
9.14.2 dia 50mm "
9.15.3 1x70mm2 bare copper down conductor run in PVC conduit of diam 32mm "
Earthing rod of 16x2400mm to be driven in earthing pit of
9.15.4 400x400x500mm(resistance R < 5 ohm) "
9.15.5 Lightening Event counter to be mounted at 1.8mt above NGL "
Page 9 of 19
Client: Awash Bank Conusltant : MTT Consulting Architects and Engineers
PLC
Location: Bale Robe Branch Contractor : Tilahun Abebe G.C
Material that Material that
must be approved can be
Item No Description by MTT and approved by Remark
Awash Bank MTT only
Supply, fix, test & Commission Twin toilet extraction fans according to where
shown on respective drawing, complete with control facility, isolator switch
flexible connection on suction end, concrete pad with vibration isolator and all
required mechanical works for complete installation. Fans shall be of the twin
type with the option for alternate operation of one duty and one stand by. Fan
shall be rated for project spacifications.
A) TW-D 1
i) Fan Capacity
Type = DYNAIR or equivalent
Capacity: 1100 lit/sec.
Esp= 350pa
B) TW-D 2
1. Fan Capacity
Type = DYNAIR or equivalent
Capacity = 750 lit/sec
Esp = 300pa
10.1.1.2 Wall Mounted Extracting Fans "
1. Fan Capacity
Type = DYNAIR or equivalent
Capacity = 200 m/h
2. Esp = 25-40 pa
10.1.1.3 Air Exhuast Inlets & Accessories "
All exhuast air grills and door grills (doouble frame) shall be approved quality
and located to ensure the correct air distribution with out stagnant regions or
draughts occuring in the room that they are serving.
iii) Supply, fix, test and commission exhaust air louver.The frame and blades
from high quality extruded aluminium profile.
Type = Air master or Equivalent
Size: 300x300mm
b) I-EF/2
i) Fan Capacity
Type = DYNAIR or equivalent
Capacity: 384Liter/second
External static head ... 150Pa
ii) Supply, fix, test and commission exhaust air louver.The frame and blades
from high quality extruded aluminium profile.
Type = Air master or Equivalent
Size: 400X400mm
10.2.2 EXHAUST AIR GRILLs /Ceiling mounted/
Supply, install, test and comission exhaust air grilles with uninsulated factory
made plenum box. The frame shall be made from high quality extruded
aluminium profile and standard (30mm) flange width.
i - Capacity =100 &130liter/sec / Eg-1
Size: 200x150mmxmm
Type: air master or equivalent
Model: ARG-HA
Page 10 of 19
Client: Awash Bank Conusltant : MTT Consulting Architects and Engineers
PLC
Location: Bale Robe Branch Contractor : Tilahun Abebe G.C
Material that Material that
must be approved can be
Item No Description by MTT and approved by Remark
Awash Bank MTT only
Supply, fix, test and commission volume control dampers.The frame shall be
constructed from galvanized steel sheet and coated with aluminium spray.Price
shall include all the necessary accessories and connecting pieces.
For duct Size: 200x200 mmxmm/ VD
10.3 MEETING HALL AIR CONDITIONING
10.3.1 FOUR WAY CEILING DIFFUSERS
All supply and return air ceiling diffusers shall be approved quality and
located to ensure the correct air distribution pattern without stagnant regions
or draughts occuring in the room that they are serving. Price shall include
sealing gaskets,all necessary accessories and connecting pieces for the proper
functioning of the systems.
. Units and components shall work with ecological refrigerant such as R-410A. "
. Compressores shall be with built-in silencers and mounted on vibration
isolators. "
. With electirical control system "
. With access panels. "
. With indoor unit conneciton ports. "
Price shall also include all the necessary accessories. "
10.5.1 a)Tri-split outdoor unit "
Supply, install & commissions Tri split air conditioning equipment consisting "
of scroll compressor, condensing unit and Evaporating unit complete "
with all accessories including pelton pad "
Cooling capacity - 12.8 kw "
Brand:GREE or equivalent "
10.5.2 b)Indoor units "
Supply, fix, test and commission cassette type indoor unit. "
/ceiling mountd/ completed with: "
. Washable filters. "
. Control system "
. Manual on-off switch with thermostat "
. Remote control unit "
. Thermostatic expansion valves "
. Condensate drain pipe "
. With all required accessories to make the system complete "
a ) CFCU-1 "
Type: GREE or equivalent "
Cooling capacity =3.6kw "
b)CFCU-2 "
Type: GREE or equivalent "
Cooling capacity =5.6kw "
10.5.3 BU Module Manifold "
Page 11 of 19
Client: Awash Bank Conusltant : MTT Consulting Architects and Engineers
PLC
Location: Bale Robe Branch Contractor : Tilahun Abebe G.C
Material that Material that
must be approved can be
Item No Description by MTT and approved by Remark
Awash Bank MTT only
supply, tesr and install insulated copper pipes for split air conditioner/ liquid & "
suction pipes/ as where shown on the drawing, including fittings "
branches,jointing hangers,brackets,support and all the necessary "
accessories. "
price shall include factory made insulation (minimum 20 mm) "
with all accessories "
Dia. 6.35 mm "
Dia. 9.52 mm "
Dia. 12.7 mm "
Dia 15.9 mm "
10.7.3 CONDENSATE PIPES for Split air conditioner "
Supply and install uPVC condensate drain pipe with trap as appropriate as
where shown on the drawing, complete with all necessary accessories & 25mm
insulation.
Dia. 25mm
Dia. 20mm
Page 12 of 19
Project :-B+G+4 Awash Bank Branch Building Project at Bale Robe
Contractor : Tilahun Abebe G.C
Consutant : MTT Consulting Architects & Engineers P.L.C
client :AWASH INTERNATIONAL BANK S.C
Item
Description
1) Toilets
1.1 Volume Dampers
Supply, fix, test and commission volume control dampers.The frame shall be constructed
1.1.1 from galvanized steel sheet and coated with aluminium spray.Price shall include all the
necessary accessories and connecting pieces.
Size
125x100mm/VD
Supply,install,test and commission IN-LINE exhaust air fan according to where shown on
2.1 respective drawings, to be mounted on slab complete with electrical control facility, flexible
connecton on suction and delivery ends, isolater switch, support with vibration isolator and
all required mechanical works for complete installation. Fan shall be rated for project
spacific. Price shall include all works required to install, test and commission the system.
a) I-EFC/1
i) Fan Capacity
Type = DYNAIR or equivalent
Capacity:400Liter/second
External static head ... 300Pa
ii) Supply, fix, test and commission exhaust air louver.The frame and blades from high
quality extruded aluminium profile.
Type = Air master or Equivalent
Size: 550X350mm
b) I-SFC/1
i) Fan Capacity
Type = DYNAIR or equivalent
Capacity: 360Liter/second
External static head ... 250Pa
ii) Supply, fix, test and commission SUPPLY air louver.The frame and blades from high
quality extruded aluminium profile.
Type = Air master or Equivalent
Size: 550X350mm
2.2 EXHAUST AIR GRILLs /Ceiling mounted/
Supply, install, test and comission exhaust air grilles. The frame shall be made from high
quality extruded aluminium profile and standard (30mm) flange width.
i - Capacity =200&400liter/sec / Egp-1
Size: 300X300mmxmm
Type: air master or equivalent
Model: ARG-HA
Colour: As per the Architect's preference
Supply, install, test and comission SUPPLY air grilles . The frame shall be made from high
quality extruded aluminium profile and standard (30mm) flange width.
i i - Capacity 250&360liter/sec / Egp-1
Size: 650X300mmxmm
Type: air master or equivalent
Model: ARG-HA
Colour: As per the Architect's preference
2.3 Exhaust air duct
a) counting extract air duct
Size: 300X275mmxmm
225X225mm
2.4 Volume Dampers
Supply, fix, test and commission volume control dampers.The frame shall be constructed
from galvanized steel sheet and coated with aluminium spray.Price shall include all the
necessary accessories and connecting pieces.
225X225mmxmm/ VD
3)Kitchen
3.1 Kitchen Exhuast Air Fan and Accessories
Supply, fix, test & Commission Twin toilet extraction fans according to where shown on
respective drawing, complete with control facility, isolator switch flexible connection on
suction end, concrete pad with vibration isolator and all required mechanical works for
3.1.1 complete installation. Fans shall be of the twin type with the option for alternate operation of
one duty and one stand by. Fan shall be rated for project spacifications.
A) Kitchen Fan
i) Fan Capacity
Type = DYNAIR or equivalent
Capacity: 1205 lit/sec.
Esp= 450pa
3.2 Kitchen Hood
Supply and install stainless steel Island canopv equipped with vapour proof lighting grease
3.2.1 filter as shown on the drawingy
Canopy size = 1300mm x 750mm x 500mm
i) Supply, fix, test and commission Supply air louver.The frame and blades from high
quality extruded aluminium profile.
Type = Air master or Equivalent
Size: 1500x600mm
3.2.2 Ventilation Ducts
Supply and install 1.2mm thick galvanized duct for kitchen ventilation as shown on the in
the drawing complete with all fixing accessories
Size
600x300mm
Material that must
Material that can be
be approved by
approved by MTT Remark
MTT and Awash
only
Bank