Professional Documents
Culture Documents
C2 Cable Datasheet 0318
C2 Cable Datasheet 0318
C2 Cable Datasheet 0318
Applications
PROCESS WEIGHING
• Batching/Blending
• Filling/Dispensing
• Level-by-Weight
• Check Weighing
Features
Hardy High Performance C2® Cable Calibration Using C2® Cable
C2® electronic calibration reduces the risk of A Hardy C2 system includes load points,
C2® Electronic Calibration accidents or contamination from test weights junction box, cabling and nstrumentation, and
•Electronic calibration without test weights Hardy C2® Certified Cable has been designed is designed to make calibration easier than
specifically for the electrically and mechanically ever before. Upon installation or re-calibration,
harsh environments found in Process Weighing your Hardy instrument automatically searches
applications. While many process variables are for C2 certified load points and records their
transmitted at a 0-10 volt or 4-20 milliamp level, performance characteristics.
signals from load or force sensors are typically
one thousand times smaller, or 0-0.010 volts. All that’s left is to verify your scale. Entering a
INTEGRATED TECHNICIAN® (IT) A ten pound change on a 100,000 pound reference point is all that’s needed to bring
•Weighing system monitoring and trouble- scale would correspond to a signal change of your system on-line within seconds. This is done
shooting 0.000001 volts (1 micro volt). Therefore, cabling by carefully distributing one or two small
must protect against electrical noise common in weights (25 to 100 lbs.) on to the scale so they
IT TI
the plant environment. are shared by all the load sensors. The scale
NTEGRATED reading should equal the value of the test
ECHNICIAN For continued high performance, it is imperative weight/s applied. Remove the weight/s and the
that moisture not enter the cable as it would scale reading should return to its original value.
increase capacitance and allow coupling of If both of these are true then the scale is
voltage from the excitation wires to the signal calibrated, verified and ready for use. If the
wires. The coupling of voltage causes “drifting” values are not true, then there are mechanical
weight indications. Use of improper cable problems with the scale that need to be
between even the finest load sensors and corrected.
instrumentation will yield poor weighing results.
The costs and time delays of removing and
replacing improper weighing system cable are
prohibitive. To insure an effective weighing
system, always specify Hardy C2 Certified Cable.
www.hardysolutions.com • 800-821-5831
COMPONENTS C2 Cable Specifications C2 Cable Color Coding
• Eight, 22 AWG Conductors In a 0.40"
TO COMPLETE Diameter Shielded Cable. Recommended wiring for color code cabling between the
YOUR HARDY • Vinyl Outer Jacket Rated At 105 Degrees C, junction box and instrumentation when using ADVANTAGE™
Meeting MIL-I-631 Class F. line and all other load points.
SYSTEM • 36 AWG, Braided Tinned Copper Shield,
Hardy Bench Scales, Floor Meeting MIL-C-7078. +Excitation Red
• Mylar Barrier Tape Wrap Meeting +Sense Blue
Scales and Load Points MIL-I-631.
Hardy carries a wide variety of strain gauge • Twisted Pair Color Coded as Gray and +Signal Green
load points, scales and instruments to ac- Violet. - Signal White
commodate your application requirements. • Individual Conductors Color Coded Green,
Blue, Red, White, Brown, Black. - Sense Brown
• Wire To Wire Insulation Resistance Minimum - Excitation Black
2,500 Ohms 50 VDC.
• Operationally Tested For Lengths Up To
+C2 Gray
ADVANTAGE Series
Load Point with 1,000 Ft.Without Intrinsic Safety Barriers And 250 - C2 Violet
C2 Calibration Feet With Intrinsic Safety Barriers.
Ordering Information
Hardy Bench or Part Number: 6020-0001-0
Floor Scales
D
Allen-Bradley® Compatible E
Plug-in Weigh Scale Modules B
A C
P S
A H
C I All information within is subject to change without notice. Visit our website for latest specifications. WAVERSAVER, C2, IT, THE BUTTON, ADVANTAGE and
K P ANY-WEIGH are registered trademarks of Hardy Process Solutions, Inc.. All other trademarks or registered trademarks are the property of their respective
owners.
HI C2 Cable 0318
0400-CABLE C2A
www.hardysolutions.com • 800.821.5831