5/28/2018 Re pa ir Pa r ts for FAR2805 Se r ie s Ra da r - slide pdf.c om

TO: All Dealers F U R U N O U S A, I N C.

RE: Repair Parts for the FAR 2805 Series
Radars  June 8, 2000
RELEASE DATE
02-00T
RELEASE NO.

Please be careful when ordering repair parts for the FAR2805 Series Radars, since not all units contain
the same parts and assemblies. This Service Advisory describes the different assemblies that you may
encounter when servicing these Radars.

CRT M onitor Assembly 

There are two different types of CRT Monitor Assemblies used in the FAR2805 Series Radars:

1. The original CRT Monitor Assembly is Mitsubishi type CDT-2901B-1A, and it is inventoried under 
P/N 000-136-185.

2. The current-production CRT Monitor Assembly  is Toshiba type CDMC-29CF301, and it is

inventoried under P/N 000-140-065.

These (complete) CRT Monitor Assemblies are interchangeable. For example: a technician can
remove the original CRT Monitor Assembly (P/N 000-136-185), and replace it with the current-
production CRT Monitor Assembly (P/N 000-140-065), or vice versa. Both (complete) CRT Monitor 
 Assemblies are interchangeable and direct replacements for one another.

However, the subassemblies  contained in these units are not  interchangeable. For example: a
technician can not use parts from an original CRT Monitor Assembly to repair a current-production
CRT Monitor Assembly.

With this in mind, please order the appropriate repair parts for the CRT Monitor Assembly contained in
the Radar. To quickly determine which CRT Monitor Assembly your customer has, verify the Radar’s
serial number, and refer to the list below. (The serial number is identified on the Equipment
Identification Tag located on the Radar Display unit).

The following serial-numbered units contain the current-production CRT Monitor Assembly.  All
other serial-numbered units contain the original CRT Monitor Assembly.

Model Serial Number  

FAR2815 3316-0172 and after.

FAR2825 3317-0336 and after. Also 3317-0327, 0328, 0331
FAR2825W 3338-0070 and after.
FAR2835S 3322-0266 and after.
FAR2835SW 3339-0054 and after.
FR2825 3315-0033 and after.
FR2825W 3340-0021 and after.

Please refer to the attached Parts List and Schematic Diagrams for detailed descriptions and P/N’s for 
the subassemblies contained in these different CRT Monitor Assemblies.

http://slide pdf.c om/re a de r/full/re pa ir-pa r ts-for-fa r2805-se r ie s-ra da r 1/7

 

5/28/2018 Re pa ir Pa r ts for FAR2805 Se r ie s Ra da r - slide pdf.c om

Antenna Uni ts for F AR2815 and F AR2825 Radars 

Original Gearboxes:

The original FAR2815 Radars used Gearbox type C2P7N2N-028. This Gearbox was provided with all
Radars identified with serial numbers 3316-0271 and below. This is the same Gearbox that was
provided with our FR2110 Radars.

The original FAR2825 Radars used Gearbox type RSB0014-029. This Gearbox was provided with all
Radars identified with serial numbers 3317-0643 and below. (Excluding S/N 3317-0640). This is the
same Gearbox that was provided with our FR2120 Radars.

These original Gearboxes will accept the following antennas:

1. AR7/10ANT4 Antenna (XN2B, 4-foot)

2. XN3B/ANT6 Antenna (XN3B, 6.5-foot)
3. AR7/10ANT8 Antenna (XN4A, 8-foot)
4. XN5A/ANT10 Antenna (XN5A, 10-foot)

These original Gearboxes can be identified at a glance; both employ the J-shaped waveguide assembly
that routes the RF energy from the Rotary Joint to the end of the Slotted Array Antenna.

If you require repair parts for the original-style Gearbox, please refer to the attached Parts List. Also,
please refer to the Schematic Diagrams contained in your FAR2805 Series Service Manual.

Current-Production Gearboxes:

The current-production FAR2815  Radars use Gearbox type RSB0074-062. This Gearbox will be
provided with all FAR2815 Radars identified with serial numbers 3316-0272 and above. This is the
same Gearbox that is provided with the FR2115 and the FR1510MK3 Radars.

The current-production FAR2825 Radars use Gearbox type RSB0074-063. This Gearbox will be
provided with all FAR2825 Radars identified with serial numbers 3317-0644 and above. (S/N 3317-
0640 also contains this current-production Gearbox). This is the same Gearbox that is provided with the
FR2125 and the FR1525MK3 Radars.

These current-production Gearboxes will accept the following antennas:

1. XN12AF/4 Antenna (4-foot)

2. XN20AF/6.5 Antenna (6.5-foot)
3. XN24AF/8 Antenna (8-foot)

These current-production Gearboxes can be identified at a glance; they do not  employ the J-shaped
waveguide assembly required with the original Gearboxes.

If you require repair parts for a current-production FAR2815 or FAR2825 Gearbox, please refer to the
attached Parts List and Schematic Diagrams.

http://slide pdf.c om/re a de r/full/re pa ir-pa r ts-for-fa r2805-se r ie s-ra da r 2/7

 

5/28/2018 Re pa ir Pa r ts for FAR2805 Se r ie s Ra da r - slide pdf.c om

An tenna Uni ts for F AR2835S Radars 

Original Gearboxes:

The original FAR2835S Radars used Gearbox type RSB-0026-3. This Gearbox was provided with all
Radars identified with the following serial numbers:

FR-2835S: S/N 3321-0032 and below

FAR-2835S: S/N 3322-0525 and below

This is the same Gearbox that was provided with our FR2130S Radars. If you require repair parts for 
the original-style FAR2835S Gearbox, please refer to the attached Parts List. Also, please refer to the
Schematic Diagrams contained in your FAR2805 Series Service Manual.

Current-Production Gearboxes:

The current-production FAR2835S Radars use Gearbox type RSB-0026-0066-1. This Gearbox will
be provided with all Radars identified with the following serial numbers:

FR-2835S: S/N 3321-0033 and above

FAR-2835S: S/N 3322-0526 and above

This is the same Gearbox that is being provided with the FR2135S Radar. If you require repair parts for 
a current-production FAR2835S Gearbox, please refer to the attached Parts List and Schematic
Diagrams.

Mechanical Parts:

If you require mechanical parts for either style Gearbox, please contact our technical staff in Camas,
WA prior to placing your order.

If you have any questions, please don’t hesitate to contact us.

Best Regards,

Furuno Service Department

http://slide pdf.c om/re a de r/full/re pa ir-pa r ts-for-fa r2805-se r ie s-ra da r 3/7

 

5/28/2018 Re pa ir Pa r ts for FAR2805 Se r ie s Ra da r - slide pdf.c om

Parts for F AR2805 Series CRT M onitor Assembly 

(Please refer to the serial number listing on page 2 of this Service Advisory)

The original FAR2805 Series CRT Monitor Assembly (Mitsubishi type CDT-2901B-1A) contains the

following subassemblies:
Item Furuno P/N

1. DEF/Socket/MCU PCB Assembly (PBG-972, 974 & 915) 000-137-758

2. Video PCB (PBG-973) 000-137-759
3. Power PCB (PBG-975) 000-137-760
4. Degaussing Coil (PCL62-09) 000-137-761
5. Transistor (HPA72R) 000-137-762
6. Flyback Transformer (PCF72-01) 000-137-763
7. Cathode Ray Tube (CRT, type 710DB39) ORG-CRT-285

The current-production CRT Monitor Assembly (Toshiba type CDMC-29CF301) contains the

following subassemblies:

Item Furuno P/N

1. Cathode Ray Tube (CRT, type 29CF) 000-790-226

2. Video/Power Supply/Neck PCB Assy (CDUC-29CF301) 000-790-227
3. Flyback Transformer (FBT-2436469) 000-790-228
4. DEF/CRT PCB Assy (CDUC-29CF301) 000-790-229

http://slide pdf.c om/re a de r/full/re pa ir-pa r ts-for-fa r2805-se r ie s-ra da r 4/7

 

5/28/2018 Re pa ir Pa r ts for FAR2805 Se r ie s Ra da r - slide pdf.c om

Parts for F AR2815 and FAR2825 Gearbox A ssembly 

The original FAR2815 Gearbox Assembly (provided with S/N 3316-0271 & below) contains the
following parts:

Item Furuno P/N

1. Modulator PCB, MD9010 008-419-260

2. Trigger PCB, RFC-9008B 008-448-430
3. MIC Assembly, RU-5072 000-141-150
4. Diode Limiter, RU-9099 000-126-369
5. IF Amplifier PCB, IF-9007 008-410-030
6. Magnetron, MG-5241F 000-100-036
7. Chassis Mounted Transistor, Q808, 2SB1259 000-116-180
8. Cooling Fan, MMF-08B24DM-R 000-113-104
9. Circulator, RC-3686 000-106-850
10. Magnetic Reed Switch, RS-1-NO 000-118-533
11. Pulse Transformer, RT-9025 000-123-823
12. 24 RPM Drive Motor, D8G-516 (Standard) 000-631-715
13. Carbon Brush for Drive Motor 000-631-716
14. Bearing Signal Generator PCB, MP-3795 008-312-370

The current-production FAR2815 Gearbox Assembly (provided with S/N 3316-0272 & above)
contains the following parts:

Item Furuno P/N

1. Modulator PCB, 03P9244A  MD 008-487-300

2. Trigger PCB, 03P9243A  RFC 008-487-260
3. MIC Assembly, RU-9371 000-140-402
4. Diode Limiter, RU-9099 000-126-369
5. IF Amplifier PCB, 03P9232 IF 008-487-240
6. Magnetron, MG-5241F 000-100-036
7. CR870, HVR-1X-40B 000-121-156
8. CR871, HVR-1X-40B 000-121-156
9. Terminal PCB, 03P9242 008-487-230
10. Circulator, RC-3686 000-106-850
11. Magnetic Reed Switch, RS-1-NO 000-118-533
12. Pulse Transformer, RT-9025 000-123-823
13. 24 RPM Drive Motor, D8G-516 (Standard) 000-631-715
14. Carbon Brush for Drive Motor 000-631-716
15. Bearing Signal Generator PCB, MP-3795 008-312-370

http://slide pdf.c om/re a de r/full/re pa ir-pa r ts-for-fa r2805-se r ie s-ra da r 5/7

 

5/28/2018 Re pa ir Pa r ts for FAR2805 Se r ie s Ra da r - slide pdf.c om

Parts for F AR2815 and F AR2825 Gearbox A ssembly (conti nu ed) 

The original FAR2825 Gearbox Assembly  (provided with S/N 3317-0643 & below, excluding S/N
3317-0640) contains the following parts:

Item Furuno P/N

1. Modulator PCB, MD9009 008-416-010

2. Trigger PCB, RFC-9008C 008-448-440
3. MIC Assembly, RU-5072 000-141-150
4. Diode Limiter, RU-9099 000-126-369
5. IF Amplifier PCB, IF-9007 008-410-030
6. Magnetron, MG-5187F 000-101-760
7. Chassis Mounted Transistor, Q808, 2SB1259 000-116-180
8. Cooling Fan, MMF-08B24DM-R 000-113-104
9. Circulator, RC-3686 000-106-850
10. Magnetic Reed Switch, RS-1-NO 000-118-533
11. Pulse Transformer, RT-9023 000-123-394
12. 24 RPM Drive Motor, D8G-516 (Standard) 000-631-715
13. Carbon Brush for Drive Motor 000-631-716
14. Bearing Signal Generator PCB, MP-3795 008-312-370

The current-production FAR2825 Gearbox Assembly (provided with S/N 3317-0644 & above, and
also with S/N 3317-0640) contains the following parts:

Item Furuno P/N

1. Modulator PCB, 03P9244B  MD 008-487-320

2. Trigger PCB, 03P9243B  RFC 008-487-280
3. MIC Assembly, RU-9371 000-140-402
4. Diode Limiter, RU-9099 000-126-369
5. IF Amplifier PCB, 03P9232 IF 008-487-240
6. Magnetron, MG-5436 000-140-762
7. CR870, MD-12N1 000-133-735
8. CR871, HVR-1X-40B 000-121-156
9. Terminal PCB, 03P9242 008-487-230
10. Circulator, RC-3686 000-106-850
11. Magnetic Reed Switch, RS-1-NO 000-118-533
12. Pulse Transformer, RT-9023 000-123-394
13. 24 RPM Drive Motor, D8G-516 (Standard) 000-631-715
14. Carbon Brush for Drive Motor 000-631-716
15. Bearing Signal Generator PCB, MP-3795 008-312-370
16. B202, Blower with Cable 000-140-764

http://slide pdf.c om/re a de r/full/re pa ir-pa r ts-for-fa r2805-se r ie s-ra da r 6/7

 

5/28/2018 Re pa ir Pa r ts for FAR2805 Se r ie s Ra da r - slide pdf.c om

Parts for F AR2835S Gearbox Assembly 

The original FAR2835S Gearbox Assembly (provided with FR-2835S S/N 3321-0032 & below, and
with FAR-2835S S/N 3322-0525 & below) contains the following parts:

Item Furuno P/N

1. Modulator PCB, MD-5145 008-200-160

2. Modulator Trigger PCB, RF5144C 008-173-720
3. Pulse Transformer, RT-4037 000-734-037
4. Magnetron, MG5223F 000-109-081
5. MIC with RU-6742A Diode Limiter Assembly 008-224-910
6. IF Amplifier with Main Bang Suppression PCB 008-457-600
7. Bearing Signal Generator, MP-7302 008-256-330
8. Cooling Fan, 109E122M102 000-109-412
9. Rotary Encoder Assembly, RE20F-120-100-B 008-256-320
10. Magnetic Reed Switch, RS-1-NO 000-118-533
11. Circulator, RC-6548S 000-126-345
12. On/Off Switch ATK21-W (for Motor) 000-479-243
13. 200/220 VAC Drive Motor, RM-7398 (Standard) 000-113-840
14. 200/220 VAC Slow Start PCB, MSS-7497 (Standard) 008-243-530
15. 380/440 VAC Drive Motor, RM-7435 (Optional) 000-114-399
16. 380/440 VAC Slow Start PCB, MSS-7497A (Optional) 008-243-540

The current-production FAR2835S Gearbox Assembly (provided with FR-2835S S/N 3321-0033 &
above, and FAR-2835S S/N 3322-0526 & above) contains the following parts:

Item Furuno P/N

1. Modulator PCB, 03P9244C MD 008-488-230

2. Modulator Trigger PCB, 03P9243D RFC 008-488-220
3. Pulse Transformer, RT-9273-0 000-136-734
4. Magnetron, MG5223F 000-109-081
5. MIC, RU-9427 000-141-059
6. IF Amplifier 03P9232A 008-488-240
7. Bearing Signal Generator, MP-7302 008-256-330
8. Cooling Fan, 109E122M102 000-128-384
9. Rotary Encoder Assembly, RE20F-120-100-B 008-256-320
10. Magnetic Reed Switch, RS-1-NO 000-118-533
11. Circulator, RC-6584S 000-126-345
12. On/Off Switch ATK21-W (for Motor) 000-479-243
13. 200/220 VAC Drive Motor, RM-7398 (Standard) 000-113-840
14. 200/220 VAC Slow Start PCB, MSS-7497 (Standard) 008-243-530
15. 380/440 VAC Drive Motor, RM-7435 (Optional) 000-114-399
16. 380/440 VAC Slow Start PCB, RM-7497A (Optional) 008-243-540

http://slide pdf.c om/re a de r/full/re pa ir-pa r ts-for-fa r2805-se r ie s-ra da r 7/7