Professional Documents
Culture Documents
JSA JIS B 7507-2016 Caliper
JSA JIS B 7507-2016 Caliper
INDUSTRIAL
STANDARD
Translated and Published by
Japanese Standards Association
(JMA/JSA)
Vernier, dial and digital callipers
ICS 17.040.30
Reference number: JIS B 7507 : 2016 (E)
PROTECTED BY COPYRIGHT 17 S
B 7507 : 2016
© JSA 2017
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized
in any form or by any means, electronic or mechanical, including photocopying and microfilm, without
permission in writing from the publisher.
PROTECTED BY COPYRIGHT
B 7507 : 2016
Contents
Page
Introduction································································································· 1
1 Scope ...................................................... ···········································1
2 Normative references············································································ 1
3 Terms and definitions ........................................................................... 2
(i)
PROTECTED BY COPYRIGHT
B 7507 : 2016
Foreword
This translation has been made based on the original Japanese Industrial
Standard revised by the Minister of Economy, Trade and Industry
through deliberations at the Japanese Industrial Standards Committee
as the result of proposal for revision of Japanese Industrial Standard
submitted by Japan Precision Measuring Instruments Association
(JMA)/Japanese Standards Association (JSA) with the draft being at-
tached, based on the provision of Article 12 Clause 1 of the Industrial
Standardization Law applicable to the case of revision by the provision of
Article 14. Consequently JIS B 7507: 1993 is replaced with this Standard.
JIS B 7507: 1993 may be applied in the JIS mark certification based on
the relevant provisions of Article 19 Clause 1, etc. of the Industrial
Standardization Law until August 21,2017.
This JIS document is protected by the Copyright Law.
Attention is drawn to the possibility that some parts of this Standard
may conflict with patent rights, applications for a patent after opening to
the public or utility model rights. The relevant Minister and the Japanese
Industrial Standards Committee are not responsible for identifying any of
such patent rights, applications for a patent after opening to the public or
utility model rights
--```,,,``,,,```,````,,,,````,`-`-`,,`,,`,`,,`---
PROTECTED BY COPYRIGHT
JAPANESE INDUSTRIAL STANDARD JIS B 7507 : 2016
Introduction
This Japanese Industrial Standard has been prepared based on the first edition of
ISO 13385-1 published in 2011 with some modifications of the technical contents in
order to correspond to the practical manufacture and use.
The portions given sidelines or dotted underlines are the matters in which the con-
tents of the corresponding International Standard have been modified. A list of modi-
fications with the explanations is given in Annex JB.
This Standard is one of geometrical product specifications (GPS) under the GPS
Basic Standard (see ISO/TR 14638 : 1995) and related to the chain link 5 for the chain
of standards on size. The details about the relation of this Standard and other GPS
Standard are given in Annex C.
1 Scope
This Standard specifies callipers equipped with analogue or digital indicating devic-
es with either a vernier scale or a circular scale.
NOTE: The International Standard corresponding to this Standard and the
symbol of degree of correspondence are as follows.
ISO 13385-1 : 2011 Geometrical product specifications (GPS) - Dimen-
sional measuring equipment - Part 1 : Callipers; Design and metrologi-
cal characteristics (MOD)
In addition, symbols which denote the degree of correspondence in the
contents between the relevant International Standard and JIS are IDT
(identical), MOD (modified), and NEQ (not equivalent) according to
ISOIIEC Guide 21-1.
2 Normative references
The following standards contain provisions which, through reference in this text,
constitute provisions of this Standard. The most recent editions of the standards (in-
cluding amendments) indicated below shall be applied.
JIS B 0641-1 Geometrical Product Specifications (GPS)-Inspection by meas-
urement of workpieces and measuring equipment - Part 1 : Deci-
sion rules for proving conformance or nonconformance with specifi-
cations
NOTE: Corresponding International Standard: ISO 14253-1 Geometrical prod-
uct specifications (GPS) - Inspection by measurement of workpieces and
measuring equipment - Part 1 : Decision rules for proving conformity or
nonconformity with specifica tions
JIS B 0642 Geometrical product specifications (GPS) - General concepts and re-
--```,,,``,,,```,````,,,,````,`-`-`,,`,,`,`,,`---
PROTECTED BY COPYRIGHT
2
B 7507 : 2016
PROTECTED BY COPYRIGHT
3
B 7507 : 2016
rh~ Jig!!r~_~ _~r~_ jnt~}:1g~_~ _W jnili~~_t~ Jh~ _ll~m.~~ h~tJ}Qt jnw_ng~_d JQ _giy:~_ fh~__
~~_~ign d~t~jJ_~!
a) M~typ_~__ C;_~Uj.p~r, having a jaw for external measurements and an independent jaw
for internal measurements. Some may be equipped with a fine adjustment device.
The calliper of maximum measurable dimension 300 mm or under may be equipped
with a depth measuring rod.
b) QM_-Jyp~_.G~lli'p~x, having a face for external measurements and that for internal meas-
urements on the identical jaw. Some may be equipped with a fine adjustment device.
4 11 2 1
8 7 8
--```,,,``,,,```,````,,,,````,`-`-`,,`,,`,`,,`---
3 5 3
1 beam 7 depth measuring rod la length of jaw for external meas-
urements
2 slider 8 measuring faces for Ib length of jaw for internal meas-
depth measurement urements
3 jaw for external meas- 9 vernier scale Z4 ___ l~m.gt.h _Q1 )J:)._~~~_~:rjn.K f..~~E?_~ _f9X_ ~~ ~
urements .t~xrr~t m~~~..lJ.X~}J.l_E?n.t.~
4 jaw for internal meas- 10 main scale lu undercut depth
urements
5 measuring faces for 11 locking screw
external measurements
6 measuring faces for
internal measurements
PROTECTED BY COPYRIGHT
4
B 7507 : 2016
7 9 2 6 1
11111111111111111111111111
o 10 20 30 40 50 60 70 80
11111111111111111111111111
8 10
5 4 5
--```,,,``,,,```,````,,,,````,`-`-`,,`,,`,`,,`---
1 beam 6 fine adjustment clamp Ia length of jaw
2 slider 7 locking screw Ib length of measuring faces for
internal measurements
3 Jaw 8 fine adjustment device (including undercut)
4 measuring faces for 9 vernier scale Ie thickness of measuring faces
external measurements
5 measuring faces for 10 main scale Z4 ___ l~pgth_QLm~~§,_l.:l:.:t;in.gJ~~_~~J9.:t;
internal measurements .~~t~r..n~l_nw~~~:r~m~nt~
Iu undercut depth
Fig~r~ __2 ____OM ~typ_~__<;~llip-~r
4.3 Dimensions
The dimensions shall be as follows.
a) The dimensions of the elements which are given in Table 1 are typical dimensions.
__ __ __ __
FQr._~_gUip-~r~ w_~tb g_Jin.~ g_gj\1~tm_~nt_g~yj~~1_th~ m~~im\1m_J.))._~_g_~:tJ.X!}k>J.~ (#m~n.~jQn.. __
m_gy.J)_~_<;Qm~_~m~U~x_by__th~J~n.gth_Qfth~_d~~i~~~
PROTECTED BY COPYRIGHT
5
B 7507 : 2016
G).... E9x..C.M.-.typ-~.~~lhp.~x,.xh~.m.~~~~rin.g.J~W.~.J9X.j.)):t~~rr~l.l))..~.~.~:tJx~m.~n..t.~h~lJ..h~~~.~.~~.h
,9:..~_h~p-~_xh~t._~.n~bl~~.t.h~._~Q.(:_lJr.g_t~_jn..t~r.J}91mg.g_~~x~m.~nt_fQr_~~~m.pI~_.thE}.. ~.h~p-~.Qf
,(:j.xQ.l~.w.:hQ~.E}.x~_Q..i~~.g9.~.~..l19_t.~~~.~.~5l_tb~_t.hid<;rr~~~._9J.m~~~~~irrg.fg_G~~1..zg:
~) ... rh~jnQ..iy:id~~~.dim.~n~j.Qn..~.Qf~:ndiQ.~t~9.l1.~h~ll~~.~~.gj.y~n...in.1:1:
4.4 Types of indicating devices
4.4.1 General
The types of indicating devices shall be classified into digital and analogue with ei-
ther a vernier scale or a circular scale.
On callipers with an analogue indicating device, the scale interval, minimum reading
value and its unit shall be labelled.
On callipers with a digital indicating device, the unit of the indication shall be la-
belled.
4.4.2 Analogue indicating devices
4.4.2.1 General
The scale interval of the main scale on the beam of a calliper with a vernier scale
shall be 1 mm. The main scale shall be longer by at least one vernier scale length than
the measuring range of the calliper.
PROTECTED BY COPYRIGHT
6
B 7507 : 2016
In the case of callipers with circular scales, the scale interval on the beam should be
1 mmor2 mm.
4.4.2.2 Vernier scale and main scale
Th~___ minim~m__ x~~Jling __ ~~l)J._~___QJ __ th~___~_~JUp-~r __with __ ~n __ ~n~l~gl!~ __ iJ.).Jli~_~_tiJ.).g __9gyj<;g
__ __ __
~g~jI>p~_g_wj_th ~_Y~xnj~x ~~~l~ ~h~ll_J)_~ __ Q!l __ mm-, __ Q!QQ __ mm__ ~r__ Q!Q2 __ mm_.__ An __~~_~_wpl~ __i~,
~hQwn_ jn J~\gJAr~ _;?_.,
1 main scale
2 vernier scale
--```,,,``,,,```,````,,,,````,`-`-`,,`,,`,`,,`---
:f)ggrg _t?
10 equal parts
Divide 19 mm into
1 :f)ggrg_Q
20 equal parts
0.05
Divide 39 mm into
:f)ggrg_l
20 equal parts
Divide 49 mm into
0.02 Figure 8
50 equal parts
PROTECTED BY COPYRIGHT
7
B 7507 : 2016
o 10 20 30 40 50 o 10 20 30 40 50
11I111111I1~\lIII/Ullllllllllldlllllllllllllllllllll \111111111/1/111111111\111111111111111111111111111111111
0246810 O.1nm o 2 4 6 8 10 O.1nm
W IE 19 ~I
NOTE: The actual reading in this figure is NOTE: The actual reading in this figure is
11.4 mm. 0.3mm.
o 10 20 30 40 50 20 30 40 50 60 70 80
IE 19 ~I IE 39 ~I
NOTE: The actual reading in this figure is NOTE: The actual reading in this figure is
1.45 mm. 30.35 mm.
o 10 20 30 40 50 60 70 80
1""I""I""II\\\\\\\\I\IIIIIIIIIIIIIIIIIII/l1llllmllnnIIIIIWIIIIIIIIIIIIIIIIIIIIIII
o 1 2 3 4 5 6 7 8 9 10 O.D2mm
IE 49 ~I
NOTE: The actual reading in this figure is 15.40 mm.
The scale line thickness of a calliper with a vernier scale shall be as given in Table 3
unless otherwise specified.
--```,,,``,,,```,````,,,,````,`-`-`,,`,,`,`,,`---
PROTECTED BY COPYRIGHT
8
B 7507 : 2016
~
cIj
1 S 2
1 main scale S
S
2 vernier scale
3 beam
4 slider 3 4
1
0.03 mm 2
1 main scale
2 vernier scale
3 beam
4 slider 3 4
1 main scale
2 circular scale 100
1I1I11I1I111I11I1!1
PROTECTED BY COPYRIGHT
9
B 7507 : 2016
2 1
Callipers with a digital display may also be capable of data transfer. In this case, the
manufacturer shall describe the data output protocol (interface) in sufficient detail.
.G~:~JUp.~r.._with_.(J..~git~l.ip.di~.~_tipg_d~~i~~._~h~n_ip.Gl~<;1&_~ __<;l~.yi~_~__ ~_~.p_~Rl~_gf.dj~p.lgY_~TIg __g.u
Q.P.~x~ti9.n .. ~n..cJ....f?y~t.~W...~XX9X.. J'))'.~.f?~~g~f? ..w.h~.TI .. r..~.p.id .. ~Rip.dl~.. XQt9:tjQP' ..GQ~ld ..G~.lJ..~~ .. th~
wXQnKiTIdi~~tj.Qn.9x.wb.~n'p'9.w.~X~.f?~p.p.h~.~9.1t.gg~..cJ.g~lin~.~.·
--```,,,``,,,```,````,,,,````,`-`-`,,`,,`,`,,`---
PROTECTED BY COPYRIGHT
10
B 7507 : 2016
on the beam and a jaw for external measurements on the slider shall not be detri-
mental to use. The slider shall be smooth over the entire operating range, be free from
harmful play, and operate without looseness.
4.7 Hardness
The hardnesses of calliper's measuring face shall be not less than 550 HV or 52 HRC
if it is made of stainless steel, and not less than 700 HV or 60 HRC if it is made of oth-
--```,,,``,,,```,````,,,,````,`-`-`,,`,,`,`,,`---
er materials.
The measuring position shall be either on the measuring faces or on the point within
2 mm from the measuring faces.
PROTECTED BY COPYRIGHT
11
B 7507 : 2016
Tolerances on the error of indication shall be limited by maximum permissible error (MPE).
rhj_~ __
~ppli~ [3__ tQ_ PJ:lX_ti~l_~:tJ.xf~_G~ _~Qn t~J~~j; _~rx~n: _{~_.~_._22 _~ncJ.__ $_G~l~_ J?hift__~XXQr__ (~ ~ a!11_wjth~
Q_1},t_~_~_G~p.tiQn!_J)_1At_9Jb~x_it~m~ __~ppJY:_QPJy._wb~n_r~_q1Air~_~_bY_Jb~_)n~rr:tJ.J9&t~x~r_{Q~_th~
.$:tJ.p-Pli~~l_b~~~d_Qn_j;h~_d~[3jgn_~p~~_ifj~9:tiQ))_(d~~igrr_~h~x~~t~~i$Jj~$2~
.NQJ~E__ :___ Th~ __~YA1)~Ql$__ Qf_~xxQr~Qf~il)di~~tjQn_~h~~~~J~ri~_ti~$__ ~ncJ.__ tb.gjr_~Qrx~[3-PQnd~.
.ing_~Y:mbQl~_~x~__ gi~~n_jn_Ann~)~_JA._
5.3.2 Partial surface contact error E (maximum permissible error EMPE)
The partial surface contact error shall be the error of indication in the case of partial
measuring face contact (3.2.2), applicable to external measurements.
--```,,,``,,,```,````,,,,````,`-`-`,,`,,`,`,,`---
PROTECTED BY COPYRIGHT
12
B 7507 : 2016
/1
--------~------
PROTECTED BY COPYRIGHT
13
B 7507 : 2016
--```,,,``,,,```,````,,,,````,`-`-`,,`,,`,`,,`---
PROTECTED BY COPYRIGHT
14
B 7507 : 2016
This is the error of indication when the measurement is performed by using the
--```,,,``,,,```,````,,,,````,`-`-`,,`,,`,`,,`---
M.~tYI>gj~w_fQX __i,:ntgxnJ~.Lm~~~!Jx~_m~nt.$, perpendicular to the length of jaws in a small
cylindrical hole of the M~t.Y.R~_~_~_Ui:R~x.
The error due to crossed knife-edge distance of M_-.tY:R_~j~w~_fQx_jnt.~xn~l_m~_~_$~X~~,
m_~nt~ shall be measured using a ring gauge not greater than 5 mm (the manufacturer
or the supplier shall state the size used in the test). The error depends on the clearance
between the jaws for internal measurements and on the thickness of the measuring
faces for internal measurements (see Figure 15).
la clearance
lb thickness of measuring faces for
internal measurements
din indicated size
dov overall size
PROTECTED BY COPYRIGHT
15
B 7507 : 2016
8 Inspection
Dimensions, type of indicating device, measuring face, construction, function, hard-
ness, metrological characteristics and performance of calliper shall be inspected, and
they shall conform to 4.3 to 4.7 and clause 5.
9 Marking
On a conspicuous position of a calliper, th~JQJJQwj)}gjt.~);'1}~__l?h9:UJ~~ __m~rk~_Q, indelibly
by the method which will not impair the metrological quality .
b2 ___ M~~im~_m_m~~~11r~Rl~_dj_m~_n~_~9_n
G)____ N~W_~__QJJh~ __m~n!Jf9:Gt11r~X_(I?~.Ppli~r2_Qr__it~_~bbx~~Ij~t_~9_n
d) Manufacturing number (alphanumeric)
--```,,,``,,,```,````,,,,````,`-`-`,,`,,`,`,,`---
PROTECTED BY COPYRIGHT
16
B 7507 : 2016
Annex A (informative)
Notes on use
A.l Since the callipers do not have measuring-force limiting device, an appropriate
and uniform measuring force shall be used for measurement. Attention should be paid
to the tendency that measurement at the end of jaw causes a relatively large error be-
cause the calliper does not adhere to the conditions prescribed in the Abbe's Principle.
A.3 In the case of digital indications, pay attention to environmental factors which
could affect the functioning of the electronic components of the calliper.
PROTECTED BY COPYRIGHT
17
B 7507 : 2016
Annex ;a (informative)
Typical of data sheet for design specification (design char-
--```,,,``,,,```,````,,,,````,`-`-`,,`,,`,`,,`---
acteristics), metrological characteristics and performance
Name of equipment
Product profile
Company name
Date, number of edition etc.
PROTECTED BY COPYRIGHT
18
B 7507 : 2016
Annex G (informative)
Relation to the GPS matrix model
Col General
For details about the GPS matrix model, see ISO/TR 14638.
NQTE_J_____ Th~_1~t~~t~Q.itiQnQfJS_Q!Tll_l46a8j~JSQ_l~H~a8_:__2_QJ}~_._
NQTE_Z_____ Th~__Gh~_inJjnk_Q_~9.:rX~~.P_9xHl~__tQ_t.h~_J;h~inhnk_E_~.P_~_Gjfi~_djnISQ_J1:~_a_6__:_
2QJ}?_..
--```,,,``,,,```,````,,,,````,`-`-`,,`,,`,`,,`---
PROTECTED BY COPYRIGHT
19
B 7507 : 2016
--```,,,``,,,```,````,,,,````,`-`-`,,`,,`,`,,`---
PROTECTED BY COPYRIGHT
20
B 7507 : 2016
Annex JA (informative)
Marking on product documents
For better visibility and understanding, the symbols given in this Standard can be
replaced by the corresponding symbols given in Table JA.1, which have fewer sub-
scripts.
Table JA.l Symbols in this Standard and corresponding symbols used for
product documents or figures
Symbols in this Standard Corresponding symbols
EMPE MPEE
RMPE MPER
SMPE MPEs
LMPE MPEL
~PE MPEJ
KMPE MPEK
PROTECTED BY COPYRIGHT
Annex JB (informative)
Comparison table between JIS and corresponding International Standard
JIS B 7507 : 2016 fernier, dial and digital callipers ISO 13385-1: 2011 Geometricalproduct specifications (GPS) -Dimen-
sional measuI1ng equipment - Part 1 : Callipers; Design and metrolog-
ical characteristics
(1) Requirements in JIS (II) Inter- (III) Requirements in (IV) Classification and details of technical (V) Justification for the
national International Standard deviation between JIS and the Interna- technical deviation and
Standard tional Standard by clause future measures
number
No. and Content No. of Content Classifica - Detail of technical de via tion
title of clause tion by
clause clause
"'d
~ 2
o Normative
~
t.:rj
o references
~
t.:rj
3 Terms 3 Almost identical Addition Add the description of the Addition of term, and no
U
to and with JIS. error of indication. substantive deviation.
~
o definitions
o
"'d 4 Design 4.1 General 4.1 Almost identical Alterna tion Divide the subclause into For clear distinction of
;a specifica- 4.2 Names of main with JIS. two. callipers, add the
""""
o
:::q tion (design parts Add the explanations for explanation of the
~ characteris- M -type and CM -type previous edition and give
tics) callipers. CM-type calliper which is
Replace the calliper used in commonly used in Japan.
the figure with CM -type No technical deviation.
calliper.
Mention that the figures
indicate names but not the
design details.
OJ
-l
01
o
-1
~
o
I--I-~
~I--I-
--```,,,``,,,```,````,,,,````,`-`-`,,`,,`,`,,`---
bjt:-:l
t:-:l
-l
Of
o
(n Requirements in JIS (II) Inter- (III) Requirements in (IV) Classification and details of technical (V) Justification for the -l
national International Standard deviation between JIS and the Interna- technical deviation and t:-:l
o
Standard tional Standard by clause fu ture measures ~
m
No. and Content number No. of Content Classifica- Detail of technical deviation
title of clause tion by
clause clause
4 Design 4.3 Dimensions 4.2 Almost identical Alternation Change the dimensions and Add the description of the
specifica- with JIS. measuring position. previous edition in order
tion (design Prescribe only the for practical values and
"'d
characteris- dimensions of callipers measuring positions.
~ tics) having the maximum Add the maximum
o
~ (continued) measurable dimension of measurable dimensions of
t:rj
o 1 000 mm or less, and specify the previous edition in
~
t:rj
U
that callipers having the order to specify practical
to maximum measurable dimensions.
~
o dimension over 1 000 mm
o shall be as agreed between
~ the parties concerned with
o
"""" delivery.
~
~ Addition Add the specification for Add the description of the
measuring length of calliper previous edition to clarify
with a fine adjustment the contents of the
device. standard and to maintain
Add the length of measuring a constant quality of
faces for external measurement.
measurements,
cross-sectional dimension of
depth measuring rod, the
shape of measuring faces for
internal measurement of
CM -type calliper.
(n Requirements in JIS (II) Inter- (III) Requirements in (IV) Classification and details of technical (V) Justification for the
national International Standard deviation between JIS and the Interna- technical deviation and
Standard tional Standard by clause fu ture measures
No. and Content number No. of Content Classifica- Detail of technical deviation
title of clause tion by
clause clause
4 Design 4.4.2.2 Vernier scale 4.3.2.2 Almost identical Addition Add the specification for Add the description of the
specifica- and main scale with JIS. minimum reading value. previous edition to
tion (design standardize the minimum
characteris- reading values.
tics) 4.4.2.3 Design of 4.3.2.3 Almost identical Addition Add the figure of graduating Add the description in the
(continued) vernier scale with JIS. method. previous edition to
"'d
~ Add the scale line thickness. maintain a constant
o
~
t.:rj quality of measurement.
o No technical deviation.
~
t.:rj
U 4.4.2.4 Scale surface of 4.3.2.4 Almost identical Addition Add the dimensions of step Add the description in the
to vernier scale with JIS. difference and clearance previous edition to
~
o between the main scale maintain a constant
o
"'d surface and vernier scale quality of measurement.
;a surface.
""""
o
:::q 4.4.2.5 Main scale and 4.3.2.5 Almost identical Addition Add the specification for Add the description in the
~
circular scale with JIS. scale intervaL previous edition to
standardize the scale
--```,,,``,,,```,````,,,,````,`-`-`,,`,,`,`,,`---
intervaL
4.4.2.6 Design of -
Addition Add the scale line thickness. Add the description in the
circular scale previous edition to
maintain a constant
quality of measurement.
OJ
-l
01
o
-1
~
o
I--I-~
~CA:l
bjt:-:l
~
-l
Of
o
(n Requirements in JIS (II) Inter- (III) Requirements in (IV) Classification and details of technical (V) Justification for the -l
national International Standard deviation between JIS and the Interna- technical deviation and t:-:l
o
Standard tional Standard by clause fu ture measures ~
m
No. and Content number No. of Content Classifica- Detail of technical deviation
title of clause tion by
--```,,,``,,,```,````,,,,````,`-`-`,,`,,`,`,,`---
clause clause
4 Design 4.4.3 Digital indicating 4.3.3 Almost identical Addition Add the specification for Add the description in the
specifica- devices with JIS. minimum digital step. previous edition to
tion (design Add the specification for standardize the minimum
"'d
characteris- error messages. digital step.
~ tics) Add the description in the
o
~ (concluded) previous edition to
t:rj
o examine visually for
~
t:rj
U
abnormalities.
to 4.4.4 Protection of 4.3.4 Almost identical Alterna tion Limit the marking of Limit the targets because
~
o digital indication for with JIS. protection code to digital it is not practical to
o field use indication with guaranteed require that all models be
~ fluid and dust protection. marked with production
o
"""" code.
~
~ Deletion Delete the description on Delete the description
electromagnetic field because it is impractical.
protection.
4.5 Measuring faces 4.4 Almost identical Addition Add the tolerances on Add the description in the
with JIS. surface roughness. previous edition to
maintain a constant
quality of measurement.
4.6 Construction and -
Addition Add the specification for step Add the description in the
function difference on the plane previous edition to
surface and the operation of maintain a constant
slider. quality of measurement.
4.7 Hardness -
Addition Add the tolerances on Add the description in the
calliper hardness. previous edition to
maintain a constant
quality of measurement.
(n Requirements in JIS (II) Inter- (III) Requirements in (IV) Classification and details of technical (V) Justification for the
national International Standard deviation between JIS and the Interna- technical deviation and
Standard tional Standard by clause fu ture measures
No. and Content number No. of Content Classifica- Detail of technical deviation
title of clause tion by
clause clause
5 -
5 Almost identical Alternation Integrate the contents of Relocate the contents of
Metrologi- AnnexA with JIS. cla use 5 and Annex A in ISO. Annex A to the body
cal charac- because the measurement
teristics methods are important for
and perfor- the JIS certification.
mance 5.3.1 General 5.3.1 Almost identical Addition Limit the application of Limited because it is
"'d
~
o with JIS. inspection basically to two impractical to require that
~
t.:rj types :E and S. all items be inspected for
o all types of callipers.
~
t.:rj
U 5.3.2 Partial surface 5.3.2 Almost identical Addition Add the list of the maximum Add the description in the
to contact error E A.2.2 with JIS. permissible error. previous edition to
~
o Add the detail on the maintain a constant
o
"'d measurement method. quality of measurement.
;a Maintain ± symbols,
""""
o
:::q according to ISO and the
~ previous edition.
Add the measurement
method in the previous
edition that is commonly
used in Japan.
OJ
-l
01
o
-1
~
o
I--I-~
~Ol
bjt:-:l
0';)
-l
Of
o
(n Requirements in JIS (II) Inter- (III) Requirements in (IV) Classification and details of technical (V) Justification for the -l
national International Standard deviation between JIS and the Interna- technical deviation and t:-:l
o
Standard tional Standard by clause fu ture measures ~
0';)
No. and Content number No. of Content Classifica- Detail of technical deviation
title of clause tion by
clause clause
5 5.3.4 Scale shift error S 5.3.4 Almost identical Alternation Add the specification for the Add the description in the
Metrologi- A.2.4 with JIS. maximum permissible error. previous edition to
cal charac- Replace the measurement by maintain a constant
"'d
teristics the difference between quality of measurement.
~ and perfor- indication of gauge block and Change to the description
o
~ mance that of ring gage, with the in the previous edition to
t:rj
o (concluded) measurement only by the specify the measurement
~
t:rj
U
error of indication of block method commonly used in
to gauge. Japan.
~
o 5.3.5 Line contact error 5.3.5 Almost identical Addition Specify that the line contact Add the practical
o L with JIS. error can be also inspected inspection method of the
~ by the clearance between previous edition.
o
"""" measuring faces for external
~
~ measurements.
-
5.4 Deletion Delete the items about MPE Delete the items for
and MPL of metrological clarifica tion.
characteristics.
6 Marking 6 Marking on product Alternation Describe the details in The maximum permissive
on product documents Annex JA, except for the error is basically as
documents indication of maximum specified in the body.
permissive errors in product
documents, figures, etc.
Delete the example of data
sheet.
--```,,,``,,,```,````,,,,````,`-`-`,,`,,`,`,,`---
(n Requirements in JIS (II) Inter- (III) Requirements in (IV) Classification and details of technical (V) Justification for the
national International Standard deviation between JIS and the Interna- technical deviation and
Standard tional Standard by clause fu ture measures
No. and Content number No. of Content Classifica- Detail of technical deviation
title of clause tion by
clause clause
7 Proof of 7.1 General 7.1 As specified in ISO Alternation Change the conformance or Replace with the practical
conform- 14253-1. nonconformance according to conformance or
ance with ISOtrR 14253-6 : 2012. nonconformance.
specifica- Delete the evaluation of
tions uncertainty.
"'d 7.2 Measurement 7.2 Almost identical Addition State the necessity to use the Add the specification to
~ standard for with JIS. standard traceable to link the standard with
o
~ calibra tion of national standards when it national standards.
t.:rj
o metrological does not correspond to the
~
t.:rj characteristics and Japanese Industrial
U
to performance Standards.
~
o 7.3 Standard reference -
Addition Specify the dimensions, error Add the concrete
o temperature of indication etc. are at the specification considering
"'d
;a standard reference the convenience for users.
""""
o temperature.
:::q
~ 8 -
Addition Specify the necessity of Added for the JIS
Inspection conformance in the certification.
inspection.
9 Marking 8 Almost identical Alterna tion Add the specification for Add the marking in the
with JIS. scale interval, minimum previous edition that is
reading value or minimum commonly used in Japan.
digital step, maximum Impracticable to make the
measurable dimension, manufacturing numbers
OJ
manufacturer's name, and sequential. -l
2-step scales. 01
o
Delete the specification of -1
sequential manufacturing ~
o
numbers. I--I-~
~ -1
bjt:-:l
00
-l
Of
o
(n Requirements in JIS (II) Inter- (III) Requirements in (IV) Classification and details of technical (V) Justification for the -l
national International Standard deviation between JIS and the Interna- technical deviation and t:-:l
o
Standard tional Standard by clause fu ture measures ~
m
No. and Content number No. of Content Classifica- Detail of technical deviation
title of clause tion by
clause clause
-
Annex C Deletion Delete the item of example of Deleted for clarity.
different types of calliper.
-
Annex D Deletion Delete the types of Deleted for clarity.
"'d measurement.
~
o -
Annex F Deletion Delete the item of calibration Deleted for clarity.
~
t:rj AnnexJA -
Addition Add the marking on product Marking is as specified in
o (informa-
~ document. the body, but this Annex is
t:rj
U tive) added for reference.
to
~
o Overall degree of correspondence between JIS and International Standard (ISO 13385-1 : 2011): MOD
o
~ NOTE 1 Symbols in sub-columns of classification by clause in the above table indicate as follows:
o
"""" - Deletion: Deletes the specification items(s) or content(s) of International Standard.
~
~
- Addition: Adds the specification item(s) or content(s) which are not included in International Standard.
- Alteration: Alters the specification content(s) which are included in International Standard.
NOTE 2 Symbol in column of overall degree of correspondence between JIS and International Standard in the above table indicates as follows:
Errata for JIS (English edition) are printed in Standardization and Quality Conti'oJ, published
monthly by the Japanese Standards Association, and also provided to subscribers of JIS
(English edition) in Monthly InfOl'mation.
PROTECTED BY COPYRIGHT