Professional Documents
Culture Documents
BSI Standards Ut Reference
BSI Standards Ut Reference
q=bsi+of+ultrasonic+testing
PRESS RELEASE
20 March 2003
This new standard is a must for testers and inspectors of welding, steels, alloy and irons.
BS ISO 17577:2006
Steel. Ultrasonic testing for steel flat products of thickness equal to or greater than
6 mm
Status : Current, Work in hand Published : October 2006
Title Steel. Ultrasonic testing for steel flat products of thickness equal to
or greater than 6 mm
Draft 05/30136468 DC
Superseded By
BS 3889-1:1983
Methods for non-destructive testing of pipes and tubes. Methods of automatic
ultrasonic testing for the detection of imperfections in wrought steel tubes
Status : Superseded, Withdrawn Published : May 1983 Replaced By : BS EN 10246-3:2000, BS EN
10246-4:2000, BS EN 10246-6:2000, BS EN 10246-8:2000, BS EN 10246-14:2000, BS EN 10246-
9:2000, BS EN 10246-13:2000, BS EN 10246-15:2000
Standard BS 3889-1:1983
Number
Draft 79/76737 DC
Superseded
By
BS 6208:1982
Methods for ultrasonic testing and for specifying quality levels of ferritic steel
castings
Status : Revised, Withdrawn Published : February 1982 Replaced By : BS 6208:1990
Standard BS 6208:1982
Number
Title Methods for ultrasonic testing and for specifying quality levels of
ferritic steel castings
Replaced By BS 6208:1990
Replaces BS 4080:1966
Draft 79/80599 DC
Superseded
By
Standard 14/30275134 DC
Number
Title BS ISO 17577. Steel. Ultrasonic testing for steel flat products of
thickness equal to or greater than 6 mm
BS EN ISO 10893-8:2011
Non-destructive testing of steel tubes. Automated ultrasonic testing of seamless and welded
steel tubes for the detection of laminar imperfections
Status : Current Published : April 2011
Status Current
Draft 09/30166479 DC
Superseded By
BS EN ISO 17640:2010
Non-destructive testing of welds. Ultrasonic testing. Techniques, testing levels, and
assessment
What is it?
BS EN ISO 17640 has four testing levels labelled as A, B, C and D. The standard
focuses on level D which requires specific ultrasonic techniques for: tests on metals
that are not iron based; tests on partial penetration welds; tests using automated
equipment; and tests at temperatures below 0°C or above 60°C. You can achieve
international compliance with BS EN ISO 17640 by testing signal length and echo or
signal character and size using a probe. These comprehensive guidelines include how
to use symbols and definitions and prepare metals, equipment and personnel
requirements, probe parameters, testing volume and evaluating results.
Foreword
1 Scope
2 Normative references
3 Symbols and definitions
4 Principle
5 Information required prior to testing
5.1 Items to be specified
5.2 Specific information required before testing
5.3 Written test procedure
6 Requirements for personnel and equipment
6.1 Personnel qualifications
6.2 Equipment
6.3 Probe parameters
7 Testing volume
8 Preparation of scanning surfaces
9 Parent metal testing
10 Range and sensitivity setting
10.1 General
10.2 Reference for sensitivity setting
10.3 Evaluation levels
10.4 Transfer correction
10.5 Signal to noise ratio
11 Testing levels
12 Testing techniques
12.1 General
12.2 Manual scan path
12.3 Testing for imperfections perpendicular to the testing surface
12.4 Location of indications
12.5 Evaluation of indications
13 Test report
Annex A (normative) Testing levels for various types of welded joints
Why BSI?
We are global, we’re independent and we’re trusted service provider to 80,000
businesses. We operate in 147 countries and are the number one certification body
in the UK and US. We created 85% of our portfolio because we know standards and
we know your business. We’re leaders and we can make you one too.
Status Current
Replaces BS EN 1714:1998
Draft 07/30135963 DC
Superseded By
BS EN ISO 11666:2010
Non-destructive testing of welds. Ultrasonic testing. Acceptance levels
Status : Current Published : January 2011
Why BSI?
We are global, we’re independent and we’re a trusted service provider to 80,000
businesses. We operate in 147 countries and are the number one certification body
in the UK and US. We created 85% of our portfolio because we know standards and
we know your business. We’re leaders and we can make you one too.
Standard BS EN ISO 11666:2010
Number
Status Current
Replaces BS EN 1712:1997
Draft 07/30135960 DC
Superseded By
BS EN ISO 23279:2010
Non-destructive testing of welds. Ultrasonic testing. Characterization of indications
in welds
Status : Current Published : March 2010
Status Current
Replaces BS EN 1713:1998
Draft 07/30151946 DC
Superseded By