Professional Documents
Culture Documents
VBR Open LM2500 Training Sept 2018 Elst
VBR Open LM2500 Training Sept 2018 Elst
VBR Open LM2500 Training Sept 2018 Elst
LM25 ing
train rse
cou
Week 39 (24 – 28 September 2018), Elst, The Netherlands. - Generator/load gearbox lube oil system
- Hydraulic oil system
- Fuel systems (SAC & DLE)
Course objective:
- Inlet air and ventilation system
This course is intended for customer personnel concerned with
- Fire protection system
day-to-day on-site operations and maintenance of the GE LM2500
- Compressor water wash system
aero-derivative gas turbine models. The purpose of the training is to
• Gas Turbine Operation
provide the knowledge required to ensure consistent, trouble-free
- General operating instructions
performance from the engine and its associated equipment.
- Gas turbine performance calculations
- Start and stop graphs
Course content:
• Gas Turbine Maintenance
• Make acquaintance and presentation of the program
- LM2500 maintenance philosophy
• Introduction to gas turbines
- Levels of maintenance
- Where it all started
- Maintenance manuals
- Introduction GT models LM2500, LM2500+ and LM2500+G4 (SAC &
• Introduction to the LM2500 Control Systems
DLE)
- Gas turbine control system, general
- Gas turbine basics
- Principle of fuel control (including DLE)
• Major Components of the LM2500, LM2500+, LM2500+G4
- Protection systems
- Inlet Section
• Troubleshooting and Cases
- High Pressure Compressor (HPC)
- Troubleshooting principles
• Principle of operation, Rotor parts, Stator parts
- Practical cases
- Control system compressor (VGC)
• Generator and Electrical System
• Principle of operation, Details of the VSV system
- Generator basics
- Combustion system (SAC & DLE)
- Capacity diagram
• Principle of operation, Details of the combustion system
- Brushless excitation (AVR)
- High Pressure Turbine (HPT)
- Protection systems
• Principle of operation, Rotor parts, Stator parts
• Remaining subjects and answers to questions
- Power Turbine (PT), type GE 6 Stage
• Evaluation of the training course
• Principle of operation, Rotor parts, Stator parts
- Bearings, sumps and frames
After completion of this training the student knows:
• The bearings, Principle of a sump, The A, B, C and D sumps
• The principles, the construction, the operation and maintenance
- Accessory Drive Assembly & Accessories
aspects of the LM2500, LM2500+ and LM2500+G4 (SAC & DLE)
• The Inlet Gearbox (IGB), Radial Drive Shaft, Transfer Gearbox
gas turbines.
(TGB) and Accessory Gearbox (AGB)
• Auxiliary Equipment & Systems of the gas turbine • The
participant will also be introduced to the gas turbine control and
- Introduction protection systems.
- Flow & Instrument Diagrams (F&ID’s) and Device List
Certificate:
- Instrumentation on/around the gas turbine
Every participant will receive a personal certificate at the closing of the
- Hydraulic starting system
course.
- Gas turbine lube oil system
VBR Turbine Partners headquarters & warehouse VBR Turbine Partners UK service office
Industrieweg Oost 6 info@vbr-turbinepartners.com Woodhall, Westoby Lane vbr.uk@vbr-turbinepartners.com
6662 NE Elst (Gld) Phone: +31(0)88 010 9000 Barrow Upon Humber, Nth. Lincolnshire Phone: +44 1469 533 337
The Netherlands www.vbr-turbinepartners.com DN19 7DJ United Kingdom www.vbr-turbinepartners.com
Independent ISO 9001/2008 certified O&M improvement experts for GE LM gas turbines, auxiliaries & packages LM1600 | LM2500 | LM5000 | LM6000
Open00
LM25 ing
train rse
cou
Course manual Receipt of the registration form will be formally confirmed by mail. An
Each trainee will receive a training manual (approximately 900 pages invoice will be included if prepayment is required.
in full color), covering the relevant subjects of the training course. The
Cancellation
manual consists of equipment descriptions, schematics and operating
If you have received a registry confirmation but are forced to cancel,
and maintenance instructions. The text is supplemented by a large
you can cancel the registration up to two (2) weeks before the course
number of illustrations, drawings and photographs of the equipment. The
commencement date. The paid amount will then be refunded. After this
manual also contains an abundance of reference information, for further
date, or in the event of a no-show, no amount will be refunded.
private studies. To support the discussed subjects, a calculation and
simulation program will be used. VBR Turbine Partners reserves the right to cancel or defer the course.
Cancellation or deferment of the training course will be notified by
Language VBR Turbine Partners two (2) weeks prior to the course date.
The training will be executed in English. The manuals are in the English VBR Turbine Partners is not responsible for any expenses incurred due
language as well. to non-refundable airline tickets or hotel accommodations.
VBR Turbine Partners FZCO Middle East service office VBR Middle East Turbine Maintenance LLC
PO Box 17573 vbr.me@vbr-turbinepartners.com PO Box 45841 info@vbr.ae
536, Techno Park Phone: +971 563 758 975 Abu Dhabi Phone: +971 563 758 975
Jebel Ali, Dubai, UAE www.vbr-turbinepartners.com United Arab Emirates www.vbr.ae
Independent O&M improvement experts for GE aero-derivative gas turbines and their auxiliary systems, control systems and packages