Professional Documents
Culture Documents
Specification Writing
Specification Writing
DIVISION 03 – CONCRETE
Contractor shall review all document in construction, labor and materials shall provide
pertaining to carpentry work as specified herein, while complying all applicable building codes
The Contractor shall specify the position of all dowels required for masonry on other construction,
including foundations.
The Contractor shall arrange the necessary space for construction materials to be in right storage at
the job site.
The Contractor shall call for all inspections required in the course of his work by Owner and/or
Building Department.
b. Constructed full height walls, concrete hollow blocks, these shall extend to slab or in the bottom
beam as if otherwise indicated on plans. Provide stiffener columns & lintel beams as specified in the
structural drawings or as specified or as deemed required to assure a stabilized wall due to height &
other considerations.
prior to plastering.
DIVISION 05 – METALS
DIVISION 06 – WOOD, PLASTICS, AND COMPOSITES
Contractor shall review all document in construction, labor and materials shall provide
pertaining to carpentry work as specified herein, while complying all applicable building codes
06 05 73 Wood Treatment
Specifier note:
Most of wood species are resistant to decay naturally that caused by other elements especially
wood resistant to termite attack.
These involves wood species that were commonly recognized as resistant to decay: black locust,
cedar, and black walnut. Eastern red cedar is also resistant to termites.
Testing: waterproofed area must be test in seventy-two (72) hours incase of seepages will occur
1. for Toilets
2. Roof
Note: Areas not mentioned above but requiring waterproofing, shall be involved in the construction
scope. Thickness should strictly be as per Manufacturers Specifications and Installation depending
on the area to be applied.
07 21 00 Thermal Insulation
Shanghai Construction Group: Provide thermal insulation sheet, Ultra Cool series.
07 21 13 Board Insulation
Shanghai Construction Group: Smart wood Fascia Board-Primer, size 20x400x1.5 cm, and
Smart wood fascia board-Primer, size 15x400x1.6 cm, painted with acrylic paint for fiber cement
wood- Brown Oak.
DIVISION 08 00 00 – OPENINGS
Confirm that openings are compliant with all applicable codes, concerning egress, lighting
and ventilation requirements.
With aluminum; Powder Coated door, the tubular frame clear full glass-
08 80 00 Glazing
All type of glass should strictly match color of existing. sample of glasses including the data of
performance shall submit by the contractor together with the manufacturer’s authentication/
certificate.
8 1 00 Glass Glazing
1. Aluminum Framed Fixed Interior Viewing Windows
a. 10 mm thick clear tempered glass for aluminum fixed windows on building interiors.
b. 8 mm thick tempered for door and big window glass areas with sill height less than 800 mm
from floor finish.
c. 6 mm thick. facial mirror with beveled edges for Toilets on 6mm thick marine plywood backing
dismantling, transfer and installation of glass doors. If there is a damage material, the contractor
9 0 00 Ceilings
1. Ceiling Finishes
a. Ceiling using SCG Smartboard four (4)-side tapered Edge Series, size 120 x 240 x 0.6
cm, concealed edge installation on galvanized iron metal ceiling frame (C-line) No. 24
tighten with SCG Needle point screw 23mm, painted over with 100 percent acrylic
paint.
b. Ceiling using SCG Smartboard Wood Grain Series, size 60 x 120 x 0.4 cm, seal the
joints with SCG Smartboard Polyurethane joint sealant.
Space lining installation on galvanized iron metal ceiling frame (C-line) No. 24,
tighten with SCG Needle point screw 23 mm.
c. Ceiling using SCG Smart board wood eaves Liner – Uncolored, size 7.5 x 300.0.8 cm,
space lining installation on galvanized iron metal ceiling frame (C-line) No. 24
Tighten with SCG Needle point screw 23mm, cover the edges with SCG Smart wood
ceiling border, size 5x300x0.8 cm
Tighten with SCG Needle point screw 23 mm, (covered nobs), painted over with
SCGA acrylic paint cement wood.
09 60 00 Flooring
1. Flooring Finishes
09 70 00 Wall Finishes
1. Brick wall with smooth cement cover, painted with acrylic paint, internal wall
using SCGA Smart wood skirt Board-Modern Series, size 7.5 x 300 x 1.2cm
2. Brick wall with smooth cement cover, finished with SCG Smart wood, Wood
Plank – Walnut, size 15 x 400 x 0.8 cm, on SCG Galvanized C-line,
Use SCG Bracket to fix it with SCG Galvanize C-Line, tighten with SCG Self Drilling
13mm (covered nobs)
3. Wall using SCG Smartboard four (4)-side Tapered Edge series, size 120 x 240 x 0.8
cm, seal the joints with SCG Smartboard Plaster Joint C-line
Tighten with SCG Needle Point Screw 23 mm, painted over with 100 percent
acrylic paint, and finished with SCG Smart wood Skirt Board-Modern series, size
7.5 x 300 x 1.2 cm.
4. Board wall with smooth cement cover, finished with ceramic wall tiles
5. RC. Wall finished with tiles of natural stone pattern
6. Glass block wall of four (4) inches
DIVISION 10 – SPECIALTIES
DIVISION 11 – EQUIPMENT
DIVISION 12 – FURNISHINGS