Professional Documents
Culture Documents
Equipped Ventilating Box: Part Number 3523A010000 3523A010000 Amdt A 3523A010000 Amdt B
Equipped Ventilating Box: Part Number 3523A010000 3523A010000 Amdt A 3523A010000 Amdt B
LIEBHERR-AEROSPACE TOULOUSE
408, Avenue des Etats-Unis
B.P. 52010
31016 TOULOUSE CEDEX - FRANCE
Tel.: 33.(0)5.61.35.28.28
Telex: LTS 531634F
Telefax: 33.(0)5.61.35.29.29
SITA: TLSBGCR
LIST OF REVISIONS
Rev. No. 1 2 3 4 5 6 7 8
Rev. Date
Page 1 of 15 Dated Jul 01/04 Page 6 of 15 Dated Jul 01/04 Page 11 of 15 Dated Jul 01/04
Page 2 of 15 Dated Jul 01/04 Page 7 of 15 Dated Jul 01/04 Page 12 of 15 Dated Jul 01/04
Page 3 of 15 Dated Jul 01/04 Page 8 of 15 Dated Jul 01/04 Page 13 of 15 Dated Jul 01/04
Page 4 of 15 Dated Jul 01/04 Page 9 of 15 Dated Jul 01/04 Page 14 of 15 Dated Jul 01/04
Page 5 of 15 Dated Jul 01/04 Page 10 of 15 Dated Jul 01/04 Page 15 of 15 Dated Jul 01/04
Revision No 0 Page 1 of 15
Initial issue: Jul 01/04
21-20-01 Jul 01/04
(F1958)
Abbreviated Component Maintenance Manual
3523A01 SERIES
TASK 21-20-01-870-801-A01
A. General
B. Description
(Ref. Fig.1)
(1) The Equipped Ventilating Box includes the main components that follow:
- a fan,
- an inlet hopper,
- an outlet hopper.
C. Characteristics
(b) Weight:
The Equipped Ventilating Box takes the outside air through the inlet hopper and delivers it through the
outlet hopper.
Revision No 0 Page 2 of 15
Initial issue: Jul 01/04
21-20-01 Jul 01/04
(F1958)
Abbreviated Component Maintenance Manual
3523A01 SERIES
General Description
Figure 1 GRAPHIC 21-20-01-991-001-A01
Revision No 0 Page 3 of 15
Initial issue: Jul 01/04
21-20-01 Jul 01/04
(F1958)
Abbreviated Component Maintenance Manual
3523A01 SERIES
Overall Dimensions
Figure 2 GRAPHIC 21-20-01-991-002-A01
Revision No 0 Page 4 of 15
Initial issue: Jul 01/04
21-20-01 Jul 01/04
(F1958)
Abbreviated Component Maintenance Manual
3523A01 SERIES
TASK 21-20-01-700-801-A01
Self explanatory.
(b) Instrumentation
C. Job Set-up
Not applicable
D. Testing Procedure
Subtask 21-20-01-210-001-A01
(a) Make sure that the unit is not damaged ; specially, make sure that there are no cracks and
impact signs on the insulation layer that covers the outlet hopper and the inlet hopper.
Subtask 21-20-01-750-001-A01
Revision No 0 Page 5 of 15
Initial issue: Jul 01/04
21-20-01 Jul 01/04
(F1958)
Abbreviated Component Maintenance Manual
3523A01 SERIES
(d) Make sure that the air flows in the correct direction through the four air outlets of the outlet
hopper.
(e) Make sure that the current consumption is less than or equal to 15.5 A.
E. Fault Isolation
TASK 21-20-01-000-801-A01
4. Disassembly
Self explanatory.
CODE DESCRIPTION
IPL FIGURE 1 /GRAPHIC 21-20-01-991-003-A01 EQUIPPED VENTILATING BOX
C. Job Set-up
Not applicable
Revision No 0 Page 6 of 15
Initial issue: Jul 01/04
21-20-01 Jul 01/04
(F1958)
Abbreviated Component Maintenance Manual
3523A01 SERIES
Subtask 21-20-01-020-001-A01
(b) Remove the clamp (01-120) from the inlet hopper (01-010).
(c) Remove the four clamps (01-110) from the outlet hopper (01-080).
(d) Remove the screws (01-090) and the flat washers (01-100).
(e) Remove the outlet hopper (01-080) from the inlet hopper (01-010).
(g) Remove the connector of the cabin fan (01-020) from its recess in the inlet hopper (01-010).
(h) Remove the screws (01-060) and the flat washers (01-070).
(i) Remove the air jet pump nozzle (01-030) from the inlet hopper (01-010).
(j) Remove the cabin fan (01-020) from the inlet hopper (01-010).
(k) Remove the fan seal (01-040) from the inlet hopper (01-010).
(l) Remove the spacers (01-050) from the inlet hopper (01-010).
TASK 21-20-01-100-801-A01
5. Cleaning
Self explanatory
(1) Use a cleaning material that agrees with the MIL-A-6090 specification.
(2) Consumables
Revision No 0 Page 7 of 15
Initial issue: Jul 01/04
21-20-01 Jul 01/04
(F1958)
Abbreviated Component Maintenance Manual
3523A01 SERIES
C. Job Set-up
Not applicable
D. Procedure
Subtask 21-20-01-110-001-A01
WARNING : USE THE APPROVED HAND AND EYE PROTECTION WHEN YOU APPLY
CLEANING AGENT. IT IS A SKIN IRRITANT.
USE IT IN AN AREA WITH A GOOD AIRFLOW.
DO NOT BREATHE THE FUMES.
CLEANING AGENT IS FLAMABLE AND POISONOUS.
6. Inspection / Check
Not applicable
7. Repair
Not applicable
Revision No 0 Page 8 of 15
Initial issue: Jul 01/04
21-20-01 Jul 01/04
(F1958)
Abbreviated Component Maintenance Manual
3523A01 SERIES
TASK 21-20-01-400-801-A01
8. Assembly
Self explanatory.
(1) Consumables
CODE DESCRIPTION
IPL FIGURE 1 /GRAPHIC 21-20-01-991-003-A01 EQUIPPED VENTILATING BOX
C. Job Set-up
Not applicable
Subtask 21-20-01-430-001-A01
(a) Apply lubricating material code (M23C) on the threads of the screws (01-060) and (01-090).
Subtask 21-20-01-430-002-A01
(a) Put the seal (01-040) in position in the inlet hopper (01-010).
(b) Put the spacers (01-050) in position in the inlet hopper (01-010).
(c) Put the cabin fan (01-020) in position in the inlet hopper (01-010).
(d) Put the air jet pump nozzle (01-030) in position in the inlet hopper (01-010).
(e) Install the flat washers (01-070) and the screws (01-060).
(f) Torque the screws (01-060) to the specified value (Ref. TASK 21-20-01-820-801-A01).
(g) Put the connector of the cabin fan (01-020) in position in its recess in the inlet hopper (01-
010).
Revision No 0 Page 9 of 15
Initial issue: Jul 01/04
21-20-01 Jul 01/04
(F1958)
Abbreviated Component Maintenance Manual
3523A01 SERIES
NOTE : Make sure that the connector of the cabin fan (01-020) is in correct position
(Ref. Fig. 1).
(i) Torque the locknut of the cabin fan (01-020) connector to the specified value (Ref. TASK 21-
20-01-820-801-A01).
(j) Put the outlet hopper (01-080) in position on the inlet hopper (01-010).
(k) Install the flat washers (01-100) and the screws (01-090).
(l) Torque the screws (01-090) to the specified value (Ref. TASK 21-20-01-820-801-A01).
(m) Install the four clamps (01-110) on the outlet hopper (01-080).
(n) Torque the screw of the four clamps (01-110) to the specified value (Ref. TASK 21-20-01-
820-801-A01).
(p) Torque the screw of the clamp (01-120) to the specified value (Ref. TASK 21-20-01-820-801-
A01).
(q) Bond the identification plate (01-130) on the inlet hopper (01-010) with adhesive material
code (M65B).
Revision No 0 Page 10 of 15
Initial issue: Jul 01/04
21-20-01 Jul 01/04
(F1958)
Abbreviated Component Maintenance Manual
3523A01 SERIES
TASK 21-20-02-820-801-A01
TORQUE VALUE
IPL FIGURE AND ITEM NO NAME daN.m (lbf.in)
minimum maximum
01-020 FAN (LOCKNUT) 0.9 (79.65) 1.1 (97.35)
01-060 SCREW 0.36 (31.86) 0.44 (38.94)
01-090 SCREW 0.36 (31.86) 0.44 (38.94)
01-110 CLAMP (SCREW) 0.225 (19.91) 0.275 (24.34)
01-120 CLAMP (SCREW) 0.225 (19.91) 0.275 (24.34)
TASK 21-20-01-940-801-A01
A. Consumable Materials
SECTION
CODE DESCRIPTION AND SPECIFICATION SUPPLIER CODE NAME AND ADDRESS
WHERE USED.
M09A USA (OM23214) OT(S.747) LOCAL VENDOR CLEANING
M23C NEVER SEEZ NSB4M F9527 ASSEMBLY
USA (MIL-A-907D) I.S.O. ROULEMENTS
5 RUE DE LA FAISANDERIE
75116 PARIS
M65B PERMABOND F246 F7527 ASSEMBLY
NATIONAL STARCH ET CHEMICAL ZI NORD
ARNAS, 299 RUE GRANGE MORIN, 69655
ARNAS
FRANCE
Revision No 0 Page 11 of 15
Initial issue: Jul 01/04
21-20-01 Jul 01/04
(F1958)
Abbreviated Component Maintenance Manual
3523A01 SERIES
Revision No 0 Page 12 of 15
Initial issue: Jul 01/04
21-20-01 Jul 01/04
(F1958)
Abbreviated Component Maintenance Manual
3523A01 SERIES
TASK 21-20-01-950-801-A01
A. Detailed Parts list
Revision No 0 Page 13 of 15
Initial issue: Jul 01/04
21-20-01 Jul 01/04
(F1958)
Abbreviated Component Maintenance Manual
3523A01 SERIES
13. Removal
Not applicable
14. Installation
Not applicable
15. Servicing
Not applicable
Revision No 0 Page 14 of 15
Initial issue: Jul 01/04
21-20-01 Jul 01/04
(F1958)
Abbreviated Component Maintenance Manual
3523A01 SERIES
TASK 21-20-01-800-801-A01
18. Appendices
No blockage
Subtask
FUNCTIONAL TESTS
21-20-01-750-001-A01
Revision No 0 Page 15 of 15
Initial issue: Jul 01/04
21-20-01 Jul 01/04
SERVICE BULLETIN
SERVICE BULLETIN
STANDARD
1. PLANNING INFORMATION
A. EFFECTIVITY
This Service Bulletin is applicable to the Equipped Ventilating Box PNR 3523A010000 or
3523A010000 Amdt A which is modified into Equipped Ventilating Box PNR 3523A010000
AMDT B or 3523A010000 AMDT AB.
B. CONCURRENT REQUIREMENTS
(1) The accomplishment of this Service Bulletin may be performed at the same time as the
accomplishment of the LIEBHERR-AEROSPACE TOULOUSE SAS Service Bulletin
3523-21-01 which consists in the improvement of the water draining of the inlet hopper.
(2) The accomplishment of this Service Bulletin must be performed later or at the same time as
the accomplishment of the TECHNOFAN Service Bulletin No. 8015-21-02 which consists in
modifying the cabin fan PNR 8015A010000 Amdt A into PNR 8015A020000.
C. REASON
This Service Bulletin is issued to introduce a new cabin fan with an improved reliability.
D. DESCRIPTION
(1) Replacement of the cabin fan (Ref. Fig. 1) and (Ref. Fig. 2):
(a) Replace the cabin fan PNR 8015A010000 by a new cabin fan PNR 8015A020000.
E. COMPLIANCE
F. APPROVAL
The technical information contained in this Service Bulletin was approved by EUROCOPTER under
the prerogatives awarded by the EASA Design Organization Approval No. 21J.056 only for the
EUROCOPTER helicopter range concerned.
G. MANPOWER
(1) Manhours required for the disassembly and the assembly with the modification of the
component is 1,5 hours.
Not changed
Not Applicable
K. REFERENCES
The Equipped Ventilating Box PNR 3523A010000 or 3523A010000 Amdt A are two-way
interchangeable with the Equipped Ventilating Box PNR 3523A010000 AMDT B or 3523A010000
AMDT AB.
2. MATERIAL INFORMATION
(1) Material
The modification to change the PNR 3523A010000 into PNR 3523A010000 AMDT B or to
change the PNR 3523A010000 AMDT A into PNR 3523A010000 AMDT AB requires:
(2) Price
(a) The cabin fan 8015A020000 post TECHNOFAN SB No. 8015-21-02 is available at a
cost of US $ 11008.15 at the economical condition of 2007.
(3) Availability
Not applicable
(1)
Vendor parts are to be purchased from :
LIEBHERR-AEROSPACE TOULOUSE SAS
408, AVENUE DES ETATS-UNIS
BP 52010
31016 TOULOUSE CEDEX - FRANCE
(2)
SB informations are to be purchased from:
TECHNOFAN
ZAC DU GRAND NOBLE
10, PLACE MARCEL DASSAULT
BP 53
31702 BLAGNAC CEDEX - FRANCE
(a) General
Not applicable
D. REIDENTIFIED PART
Not applicable
No applicable
3. ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL
B. DISASSEMBLY
(1) Remove the Cabin Fan (01-020) from the Equipped Ventilating Box (Ref. ACMM 21-20-01,
“Disassembly” chapter, TASK 21-20-01-000-801-A01).
C. ASSEMBLY
(1) Install the Cabin Fan (01-020) (Ref. ACMM 21-20-01, “Assembly” chapter, TASK
21-20-01-400-801-A01).
(2) Put the letter “B” on the identification plate of the component.
D. TEST
(1) Do all the tests of the complete component (Ref. ACMM 21-20-01, ”Testing and Fault
Isolation” chapter, TASK 21-20-01-700-801-A01) and fill the Acceptance Test Repair Data
Sheet (ATRDS) in the Appendix B.
E. CLOSE UP
Not applicable
APPENDIX A
Initial Issue : Feb 19/07 3523-21-02
Revision 0 : Feb 19/07 Page 10 of 12
SERVICE BULLETIN
APPENDIX B
A. General
The ATRDS is a document specific to the Liebherr Aerospace Agreed Repair Stations.
PRELIMINARY TESTS
FUNCTIONAL TESTS
APPENDIX B
Initial Issue : Feb 19/07 3523-21-02
Revision 0 : Feb 19/07 Page 11 of 12
SERVICE BULLETIN
APPENDIX B
Initial Issue : Feb 19/07 3523-21-02
Revision 0 : Feb 19/07 Page 12 of 12