Professional Documents
Culture Documents
Micro Project: Title of Project Feed Check Valve
Micro Project: Title of Project Feed Check Valve
MICRO PROJECT
TITLE OF PROJECT
FEED CHECK VALVE
Coursecode:22053
1
Date: 25/11/2021
MAHARASHTRA STATE BOARD OF TECHNICAL EDUCATION
CIRTIFICATE
INDEX
2
SR.NO. CONTENT PAGE NO.
1 INTRODUCTION 1
5 CONCLUSION 11
6 REFERENCE 13
ACTION PLAN: -
SR Details of activity Name of
Planned Planned
NO responsible Roll no
start date finish date
team member
1 Discussion and finalization of 23/11/21 25/11/21 Ashish Undru 7
3
topics
Preparation and submission of Shreyash
2 abstract 23/11/21 25/11/21 Mohite 8
4
CERTIFCATE OF COMPLETION
CERTIFCATE OF COMPLETION
5
This certificate is awarded to SHREYASH MOHITE
Enrollment Number: - 1916430103 of program MECHANICAL
ENGINEERING for successful completion of Micro – Projects require as
part of I–Scheme for Maharashtra State Board of Technical Education,
Mumbai.
CERTIFCATE OF COMPLETION
6
part of I–Scheme for Maharashtra State Board of Technical Education,
Mumbai.
INTRODUCTION: -
7
WHAT IS FEED CHECK VALVE?
Feed Check Valves are one of the most important components of boiler which
control the flow of water from feed pump to the boiler and further prevents the
backflow of water from boiler to pump when the boiler pressure is more than the
pump pressure or when feed pump stops working. Feed check valves are a
development of our boiler valve range of Screw-down Stop Valves and the design
makes use of a conventional Angle Pattern Stop Valve to which is connected a
separate inlet branch which houses the check valve. This check inlet branch is of
unique design in that the check valve head and its guide are arranged below the face
of the connecting flange enabling the branch to be withdrawn without disturbing
the feed piping.
8
With the stop valve closed this feature permits speedy examination and
maintenance of the check valve seating’s when the boiler is under steam. For
temperatures up to saturated steam at 263 lbf/in2 the check valve also is of special
design incorporating a resilient seal to provide completely tight shut-off when the
boiler pump cuts out, an essential feature for installations where a centrifugal pump
is employed.
The function of a feed check valve is to control the flow of water from the feed
pump to the boiler and to prevent the backflow of water from the boiler to the
pump when the pump pressure is less than the boiler pressure or when the feed
pump ceases to work.
9
DETAILS
Parts of Feed Check Valve: -
Following are the main parts of a knuckle joint:
1. Body
2. Valve Seat
3. Valve
4. Cover
5. Spindle
6. Gland
7. Stud & Nut
8. Handle
10
1. Valve Body
It is the main structure comprising all parts, holding each component in
position.
2. Valve Seat
The seat on which valve seats.
3. Valve
It is part of the valve body that restricts the flow amount of fluid that is
not required.
4. Cover
It is used to cover valve body.
5. Spindle
It The main component carrying the valve on which a force is applied
manually or automatically, in order to make the valve work.
6. Gland
The part of the valve which retains or compresses the stem packing in a
stuffing box.
7. Stud & Nut
Stud is used to operate the spindle. Nut is screwed onto the external
threaded stud and external threading of the spindle.
8. Handle
It is wheel connected to spindle, with the help of which an operator can
control the flow of fluid by spinning it manually.
11
o 316 Stainless Steel—The most popular material for check valves based on volume,
stainless steel is a corrosion-resistant material, so it stays fairly rust free in applications like
water, moist air, and steam. It is a relatively low-cost material in relation to its corrosion-
resistant properties.
o Carbon Steel – Carbon Steel is a lower cost material that is easier to machine.
Overall, expenses can be reduced by using carbon steel, however, it doesn’t have the same
corrosion-resistant properties as stainless steel. If the application is in a dry environment,
such as dry gas or a hydraulic liquid that doesn’t have water in it, then carbon steel is
effective and there is no need to pay extra for stainless.
o Brass – In many applications, brass falls somewhere between carbon and stainless
steel when it comes to corrosion resistance and price. Brass has some additional corrosion-
resistant properties over carbon steel and it is easier to machine than stainless steel. Brass
is used often in water and drinking water applications.
o Monel – Monel is a group of nickel alloys and considered a super alloy. Its biggest
advantage its really high corrosion resistance. Monel is specifically known to be effective in
saline, salt, or seawater environments. Each super alloy has different chemical resistant
properties. Some do well in one environment where others may do well in a different
environment.
o Alloy 20 – Alloy 20 is an austenitic alloy that many consider to be a hybrid between
stainless and other super alloys. It’s typically not as expensive as a many super alloys, but
it’s more highly corrosion resistant than a traditional stainless steel in certain applications.
12
Advantage of using Feed Check Valve: -
Following are the advantages of using Feed check valve:
1) Prevents backflow
2) Maintains pressure
3) Serves as backup system
4) Most can be used horizontally as well as vertically
CONCLUSION: -
REFERENCE: -
WIKIPEDIA
GOOGLE
ONLINE PLATFORM
13