Professional Documents
Culture Documents
Scilogex MS-HS10 and MS-M-S10 Hotplate and Magnetic Stirrer User Manual
Scilogex MS-HS10 and MS-M-S10 Hotplate and Magnetic Stirrer User Manual
User Manual
MS-H-S10 10-Channel Analog Hotplate Magnetic Stirrer
Please read the User Manual and the related Video of this
instrument on our website carefully before use, and follow
all operating and safety instructions!
Cat No.12300136
Contents
Contents 1
Preface 2
Service 2
Warranty 2
1 Safety Instructions 3
2 Propervse 4
3 Inspection 4
3.1 Receiving Inspection 4
3.2 Listing of Items 4
4 Trial run 5
5 Control Elements 5
6 Operation 6
7 Faults 6
8 Maintenance and Cleaning 6
9 Associated Standards and Regulations 7
10 Technical Data 7
11 Products and Accessories 8
1
MS-H(M)-S10 10-Channel Analog (Hotplate) Magnetic Stirrer
2
MS-H(M)-S10 10-Channel Analog (Hotplate) Magnetic Stirrer
1 Safety Instructions clean, non-slip, dry and fireproof surface, do not operate
the instrument in explosive atmospheres, with hazardous
Warning! substances or under water.
• Read the operating instructions carefully • Gradually increase the speed. Reduce the speed if :
before using the instrument. - The stirring bar breakaway because of too high speed
• Ensure that only trained staff work with the - The instrument is not running smoothly, or container
instrument. moves on the base plate.
• Forbid to heat the substances with low- • Temperature must always be set to at least 25 ℃ lower
burning point or easy-volatile(MS-H-S10) than the burning point of the media used.
• Beware of hazards due to:
Risk of burn! - Flammable materials or media with a low boiling
• Caution when touching the housing parts and temperature
the heating plate. The heating plate can reach - Overfilling of media
temperatures of 120 ℃. - Unsafe container
• Pay attention to the residual heat after • Process pathogenic materials only in closed vessels.
switching OFF the instrument. • If the case of the stirrer bar is PTFE,please note:
Protective ground contact! - Elemental fluorine, three fluoride and alkali metals will
• Make sure that socket must be earthed corrode the PTFE and Halogen alkanes make it expansion at
(protective ground contact) before use. room temperature
- Molten alkali ,alkaline earth metals or their solution,
• When work ,wear the personal guard to avoid the risk as well as the powder in second and third ethnic of the
from: periodic table of elements will have chemical reaction with
- Splashing and evaporation of liquids PTFE when temperature reaches 300 ~ 400 ℃ .
- Release of toxic or combustible gases. • The voltage stated on the label must correspond to the
• Set up the instrument in a spacious area on an stable, main power supply.
3
MS-H(M)-S10 10-Channel Analog (Hotplate) Magnetic Stirrer
• Ensure that the mains power supply cable does not touch mentioned in Chapter 1.
the heating base plate. Do not cover the device.
• The instrument may only be opened by trained experts 3 Inspection
• Keep away from high magnetic field.
• Observe the minimum distances between the devices, 3.1 Receiving Inspection
between the device and the wall and above the assembly
(min. 100 mm). Unpack the equipment carefully and check for any damages
which may have arisen during transport. If it happens, please
>100mm contact manufacturer for technical support.
Note:
If there is any apparent damage to the system,
please do not plug it into the power line.
>100mm
4
MS-H(M)-S10 10-Channel Analog (Hotplate) Magnetic Stirrer
• Add the medium into the vessel with a stirring bar. Figure 2
• Put the vessel above spots on the plate.
• Turn the speed control knob slowly to the ideal scale
• Turn the temperature control knob slowly to the ideal
scale(MS-H-S10)
• Keep the temperature control knob and the speed control Figure 3
knob slowly to the lowest position to turn off the function. Items Descriptions
If these operations above are normal, the device is ready Set the rated rotary speed in the safe
to operate. If these operations are not normal, the device Speed control stirring range from 0 to 1100 rpm. The
may be damaged during transportation, please contact knob function “Stirring” is switched ON
manufacturer for technical support. or OFF via the knob.
Set the rated temperature in the
Temperature safe temperature range from room
control knob temperature to 120℃. The function
(MS-H-S10) “heating” is switched ON or OFF
via the knob.
5
MS-H(M)-S10 10-Channel Analog (Hotplate) Magnetic Stirrer
When the device is switched ON, the • The stirring function will continue to operate at the speed
LED Power set point before the fault took place.
LED power is lit.
Mains switch Switch ON or OFF. • The heating function will continue to operate at the set
Table 2 point before the fault took place.
• If the problem is not solved, please contact the technical
6 Operation service center.
• Ensure the temperature control knob and the speed Control
knob at the lowest position .Put the device on the stable and 8 Maintenance and Cleaning
safe place and plug in the mains power.
• Turn ON the power switch and LED power is lit. • Proper use and maintenance can keep instruments working
• Turn the speed control knob to set the rated rotary speed in in a good state and lengthen its life time.
the safe speed limit from 0 to 1100 rpm. • Be careful not spray the cleanser into the instrument when
• Turn the temperature control knob to set the rated cleaning.
temperature in the safe limit from room temperature to • Unplug the power line when cleaning.
120℃(MS-H-S10). • Only use cleanser that we advised as below:
• The device begins to work. Dyes Isopropyl alcohol
Note: Construction
Water containing tenside / isopropyl alcohol
If there is any apparent damage to the system, materials
please do not plug it into the power line. Cosmetics Water containing tenside / isopropyl alcohol
Foodstuffs Water containing tenside
Fuels Water containing tenside
7 Faults Table 3
• If a unit fault happens, please power down the instrument. • Other method ,please contact manufacturer.
• Switch ON the unit again. • Wear the proper protective gloves during cleaning of the
instrument.
6
MS-H(M)-S10 10-Channel Analog (Hotplate) Magnetic Stirrer
7
MS-H(M)-S10 10-Channel Analog (Hotplate) Magnetic Stirrer
8
MS-H(M)-S10 10-Channel Analog (Hotplate) Magnetic Stirrer
SCILOGEX, LLC
1275 Cromwell Ave.
Suite C6
Rocky Hill, CT 06067 USA
Tel: +1(860) 436-9221
Fax: +1(860) 436-9745
info@scilogex.com | www.scilogex.com