Professional Documents
Culture Documents
Dial Test Indicators
Dial Test Indicators
Catalog No.E12035
Drastically Enhanced Durability, Sensitivity and Visibility
Lever Type Dial Indicator Improvement in visibility
Conventional New
Crystal
Bezel
Flange
Easy to remove Hard to remove Dovetail
Movement
Conventional New
Frame
Contact point Cover
(on stylus)
2
A choice of dial position Features 1
Our product lineup offers four models, each with a different orientation of of the
dial on the frame to allow best visibility of the dial face in any specific situation.
• Horizontal type: the standard model - the dial is on top of the frame.
• Vertical type: the model with the dial on the end of the frame.
• Horizontal (20° tilted face) type: the model with the dial on top of the frame
but tilted backward at 20°.
• Parallel type: the model with the dial on the side of the frame.
Maintaining trackability
• The ability of the indicator to track small changes in
displacement deteriorates due to minute changes in
clearance between the gears with prolonged use.
Redesigned mounting for the gears enables the new
models to maintain good trackability. Indicator trackability depends on maintaining gear-train stability
3
Drastically Enhanced Durability, Sensitivity and Visibility
Lever Type Dial Indicator Inspection
Limit hand
4
Features 2
certificate attached
L2
Test method
Sandpaper
70
60
Depth of wear (µm)
50
Carbide
40
30
20
10
Ruby
0
0 1 3 5
Rotation length (km)
5
Horizontal (Standard model)
Metric Provides wide variations of models conforms to the required accuracy, range, and surface of workpieces.
.9
Standard Long stylus
33
Contact point No. 137557 Double scale spacing Contact point No. 131324 Carbide contact
Carbide contact point (Anti-magnet)
point (Anti-magnet) Double scale spacing
(non-magnet) (non-magnet)
Contact point No. 21CZA210 Standard Contact point No. 21CZA201 Standard
Double scale spacing
17
18
513-404-10T/513-404-10C 513-415-10T
17
.0
Long stylus
41
Standard
Carbide contact Carbide contact
Contact point No. 103006 Contact point No. 136013
point (Anti-magnet) point (Anti-magnet)
6
Graduation: 0.01mm Graduation: 0.002mm
Range: 1.0mm Range: 0.2mm
.2
15
(non-magnet) (non-magnet)
.0
41
Contact point No. 21CZA211 Long stylus Contact point No. 21CZB068 Standard
15
18
counter counter
Contact point No. 137557 Double scale spacing Contact point No. 103011 Carbide contact
Carbide contact point (Anti-magnet)
point (Anti-magnet)
513-405-10T
15
Standard Compact
Contact point No. 103011 Carbide contact Contact point No. 103011 Carbide contact
point (Anti-magnet) point (Anti-magnet)
.2
11
7
Horizontal (Standard model)
Inch
in
5
n
0.6
5i
Standard Compact
0.6
1i
5i
0.6
Standard Standard
0.6
512-479-10E 513-463-10E
1i
512-479-10 513-463-10
0.6
8
Metric/inch Inch/Metric
in
Carbide contact Carbide contact
5
15
0.6
point (Anti-magnet) point (Anti-magnet)
Contact point No. 103011 Contact point No. 133195
DIMENSIONS
L1 38.7
L1 38.7
L2 L2
ø8 -0.03
ø8 -0.03
0
0
8.7
8.7
27
27
18
18
8.85
8.9
9
Horizontal (Standard model)
SPECIFICATIONS
Metric
Order No. Indication accuracy
(Anti-magnet)
(non-magnet)
Dial Measuring
Graduation Range Mass
reading Measuring 10 scale Hysteresis Repetability
Long stylus
Basic set Plus set Full set force
Compact
Standard
range divisions
Inch
Order No. Indication accuracy
(Anti-magnet)
(non-magnet)
Dial Measuring
Graduation Range Mass
Long stylus
Basic set Plus set Full set reading One rev. Hysteresis Repetability force
Compact
Standard
513-402-10E – 513-402-10T ✓ ✓
0.3N or less
513-472-10E – – ✓ ✓
45g
513-412-10E – 513-412-10T 0.0005 in 0.03 in 0-15-0 ±0.0005 in 0.0002 in 0.0002 in ✓ ✓
0.2N or less
513-479-10E – – ✓ ✓
513-462-10E – – 41g ✓ ✓
513-403-10E – 513-403-10T ✓ ✓
45g 0.3N or less
513-473-10E – – 0.0001 in 0.008 in 0-4-0 ±0.0001 in 0.0001 in 0.00004 in ✓ ✓
513-463-10E – – 41g ✓ ✓
Metric/Inch
Order No. Indication accuracy
With revolution counter
(Anti-magnet)
(non-magnet)
Dial Measuring
Graduation Range Mass
reading Measuring 10 scale Hysteresis Repetability
Long stylus
range divisions
Inch/Metric
Order No. Indication accuracy
With revolution counter
(Anti-magnet)
(non-magnet)
Dial Measuring
Graduation Range Measuring Mass
Long stylus
Basic set Plus set Full set reading Hysteresis Repetability force
Compact
Standard
range
513-406-10T 0.0005
in 0.03 in 0-15-0
513-406-10E – /0.01mm /0.7mm /0-35-0 ±0.0005 in 0.0002 in 0.0002 in 45g 0.3N or less ✓ ✓
10
Parallel (The scale can be read from the front, with the contact point pivoting in a plane parallel to that of the dial face)
Metric
.2
.4
Carbide contact
15
17
Inch
Carbide contact
18
Contact point No. 137557 Carbide contact Contact point No. 133195 point (Anti-magnet)
point (Anti-magnet)
SPECIFICATIONS
Metric
Order No. Indication accuracy
(Anti-magnet)
(non-magnet)
Long stylus
Dial Measuring
Compact
Standard
Graduation Range Mass
Basic set Plus set Full set reading Measuring 10 scale Hysteresis Repetability force
range divisions
513-484-10E 513-484-10A 513-484-10T 0.01mm 0.8mm 0-40-0 9µm 5µm 4µm 3µm ✓
513-485-10E – – 0.002mm 0.2mm 0-100-0 4µm 2µm 3µm 1µm 53g 0.3N or less ✓
513-486-10E – – 0.01mm 0.5mm 0-25-0 6µm 5µm 4µm 3µm ✓ ✓
Inch
Order No. Indication accuracy
(Anti-magnet)
(non-magnet)
Long stylus
Dial Measuring
Compact
Standard
– 513-482-10A 513-482-10T 0.0005 in 0.03 in 0-15-0 ±0.0005 in 0.0002 in 0.0002 in 53g 0.3N or less ✓
* Stem with ø6 dovetail groove is not included in the mass.
* Be sure to perform calibration with reference gage, etc. after exchanging the contact point. The inside parts may be damaged when the contact point is exchanged due to the breakage.
In the case the of the significant deterioration in the operation, repair is required.
DIMENSIONS
* ※背面にアリ板はありません。
No dovetail in the back. 17.5 Unit: mm
21.2 6.9
ø8 -0.03
0
3.9
8.8
17
23.5
22.3
ø40
72.1
45.9
Order No. L1 L2
513-484-10E 20.9 17.4
513-485-10E 18.7 15.2
L1
L2
11
Vertical (Best suited for centering holes under the spindle of a machine tool)
Metric
15.2
17.4
Graduation: 0.01mm
Range: 0.5mm
513-456-10 513-456-10E
Double scale spacing
Carbide contact
18.7
point (Anti-magnet)
Contact point No. 137557
Inch
12
SPECIFICATIONS
Metric
Order No. Indication accuracy
(Anti-magnet)
(non-magnet)
Dial Measuring
Graduation Range Mass
reading Measuring 10 scale Hysteresis Repetability
Long stylus
Basic set Plus set Full set force
Compact
Standard
range divisions
513-454-10E 513-454-10A 513-454-10T 0.01mm 0.8mm 0-40-0 9µm 5µm 4µm 3µm ✓
513-455-10E 513-455-10A 513-455-10T 0.002mm 0.2mm 0-100-0 4µm 2µm 3µm 1µm 46g 0.3N or less ✓
513-456-10E – – 0.01mm 0.5mm 0-25-0 6µm 5µm 4µm 3µm ✓ ✓
Inch
Order No. Indication accuracy
(Anti-magnet)
(non-magnet)
Dial Measuring
Graduation Range Measuring Mass
Long stylus
Basic set Plus set Full set reading Hysteresis Repetability force
Compact
Standard
range
DIMENSIONS
Unit: mm
ø40 17.5
ø8 -0.03
0
55.4
59.4
23.5
L1
Order No. L1 L2
L2
13
Horizontal ( 20° Tilted Face) (Dial face inclined 20°, compared with the vertical type, allows easy reading)
Metric
.2
With revolution With revolution
17
15
counter counter
Contact point No. 103006 Carbide contact Contact point No. 103011 Carbide contact
point (Anti-magnet) point (Anti-magnet)
Inch
5i
5i
counter counter
0.6
0.6
n
0i
0i
1.2
Contact point No. 136290 Carbide contact Contact point No. 136290 Carbide contact
point (Anti-magnet) point (Anti-magnet)
n
1i
1i
counter counter
0.6
0.6
14
SPECIFICATIONS
Metric
Order No. Indication accuracy
(Anti-magnet)
(non-magnet)
Dial Measuring
Graduation Range Mass
reading Measuring 10 scale Hysteresis Repetability
Long stylus
Basic set Plus set Full set force
Compact
Standard
range divisions
513-444-10E 513-444-10A 513-444-10T 0.01mm 1.6mm 0-40-0 16µm 5µm 5µm 3µm ✓ ✓
48g 0.3N or less
513-445-10E 513-445-10A 513-445-10T 0.002mm 0.4mm 0-100-0 6µm 2µm 4µm 1µm ✓ ✓
Inch
Order No. Indication accuracy
(Anti-magnet)
(non-magnet)
Dial Measuring
Graduation Range Measuring Mass
Long stylus
Basic set Plus set Full set reading Hysteresis Repetability force
Compact
Standard
range
– 513-442-10A 513-442-10T ✓ ✓
0.3N or less
– 513-442-16A 513-442-16T ✓ ✓
0.0005 in 0.06 in 0-15-0 ±0.0005 in 0.0002 in 0.0002 in
– 513-446-10A 513-446-10T ✓ ✓ ✓
48g 0.2N or less
– 513-446-16A 513-446-16T ✓ ✓ ✓
– 513-443-10A 513-443-10T ✓ ✓
0.0001 in 0.016 in 0-4-0 ±0.0002 in 0.0001 in 0.00004 in 0.3N or less
– 513-443-16A 513-443-16T ✓ ✓
* Stem with ø6 dovetail groove is not included in the mass.
* Be sure to perform calibration with reference gage, etc. after exchanging the contact point. The inside parts may be damaged when the contact point is exchanged due to the breakage.
In the case the of the significant deterioration in the operation, repair is required.
DIMENSIONS
Unit: mm
L1 55.7
L2
8.7
ø40
ø8 -0.03
0
20°
Order No. L1 L2
513-445-10E 18.7 15.2
16
Refer to MEASURING INSTRUMENTS CATALOG No. E2016 for the accessories such as styli, stems with dovetail, holding bars, etc.
15
068 1612(1)A-(CH)HS, Printed in Japan
Coordinate Measuring Machines Vision Measuring Systems Form Measurement Optical Measuring
Whatever your challenges are, Mitutoyo
supports you from start to finish.
http://www.mitutoyo.co.jp/global.html
Mitutoyo Corporation
20-1, Sakado 1-Chome,
Takatsu-ku, Kawasaki-shi,
Kanagawa 213-8533, Japan
Note: Product illustrations are without obligation. Product descriptions, in particular any and all technical
specifications, are only binding when explicitly agreed upon. T +81 (0) 44 813-8230
MITUTOYO and MiCAT are either registered trademarks or trademarks of Mitutoyo Corp. in Japan and/or other countries/regions.
F +81 (0) 44 813-8231
Other product, company and brand names mentioned herein are for identification purposes only and may be the
trademarks of their respective holders. http://www.mitutoyo.co.jp