Professional Documents
Culture Documents
TENTATIVE BILL OF QUANTITIES FOR CIVIL WORKS - Unpriced
TENTATIVE BILL OF QUANTITIES FOR CIVIL WORKS - Unpriced
GRAND TOTAL -
REV. No. 0
Providing and laying brick masonry work with well burnt 1st class
table moulded, good quality approved bricks in 1:6 Cement Mortar (1
Cement : 6 Coarse Sand by volume) in true line, level and plumb for
wall foundations, trenches, pedestals, columns, compound walls,
steps, pillars etc., complete with necessary scaffolding, raking of
joints, curing etc., complete as directed and specified upto plinth level.
Rate to include soaking of bricks adequately before construction,
complete as directed and specified. (Brick of min strength
100kg./sq.cm.)
cum -
4.2 All works above plinth level upto floor V level 434.87 Cum -
All works above plinth level upto floor V level 685.06 Sqm -
The door frames and door shutters are primed with Zinc-Phosphate
Stoving Primer and finished with Polyurethane Aliphatic grade or
epoxy paint as per approved manufacturer specifications. (Supplier
-Shakti Met-dor or approved equivalent). (Note - Test certificates
should be available for vision panels as part of the fire door assembly.
Independent glass test certificates will not be accepted. Manufacturer
test certificate shall cover doors both single and double leaf and all
doors supplied should be within the tested specimen, deviation in
specification and sheet thickness other than what is mentioned in the
test certificates are not allowed. Proper label confirming the type of
door and the hourly rating is mandatory.) The contractor should
submit shop drawing for approval from consultant / client before
execution
12.60 sqm -
5.2 Providing and fixing M.S.Door of standard rolled steel sections joints
mitred and welded with iron lugs embedded in cement concrete 1:2:4
(1 cement : 2 coarse sand : 4 Graded Stone aggregate) blocks or with
wooden plugs and screws or with rawl plugs and screws or with fixing
clips or with nuts and bolts including providing and fixing glass panes
with glazing clips and all surface painted with zinc chromate
red/yellow oxide and metal putty, minimum two coats of enamel
paint (of approved make and shade) by spraying to give even and
smooth finish.
sqm -
5.4 All Charges for Supplying and fixing in position the following mild
steel rolling shutters of approved manufacturer having 18 gauge sheet
lanths including pressed steel bottom rails, channel guides, ball
bearings, suspension shaft, bolts, screws, brackets, hood, locking
arrangement and grills for ventilation including all fittings and
accessories as per drawings and specifications including one shop
coat of red oxide zinc chromate primer, crafting, packing, transporting
to site all freight and insurance charges, assembling fitting and fixing
at all elevations and a coat of red oxide zinc chromate primer and
synthetic enamel paint as per note no. 2 above etc., complete as per
drawing and specifications and as directed by En ineer-in-charge.
(Gandhi automation)
Self coiling type Motor operated (Sizes - As per drawing) 80.00 sqm -
5.5 Providing and fixing MDF door with matt finished laminates
including hinges, latches and lipping finished The rate shall include
supplying and fixing necessary hardware as per requirement etc
39.38 sqm -
Sl.No Description of Item Qty Unit Rate Amount Rs.
5,6 Providing and fixing MS Grills for Windows,and Ventilators of
approved design with one coat of Red oxide & painting applied. Rate
include cost of materials, labour, fixing, etc, to complete
1,000.00 kg -
6.2 Providing and laying anti skid ceramic Tiles laid on average 12mm
thick cement plaster with 1:3 cement mortar and jointed with neat
white cement slurry mixed with suitable pigment to match the shade
of the tiles. Rate should include cost of material, labour, polishing, etc
to complete.(basic rate of tile Rs.500/- per sqmtr (sizes as per
drawing)
100.00 sqm -
188.36 sqm -
1,509.38 sqm -
6.5 All Charges for Providing & laying well compated M15 grade
screedconcrete flooring with neat cement & power trowelled to get
desired smooth, finishing & levelling including shuttering, cutting
grooves & curing etc. (75mm thick)
20 sqm -
8.3 Prepare the surface of underside of R.C slab, staircases and sides of
columns and soffit of beams, etc and Plaster with c.m 1: 3 to an
average thickness of 12 mm finished with Sponge in all floors
wherever necessary including chipping concrete surfaces, scaffolding
and staging works and labour charges., etc. complete. Ceiling
4,452.00 sqm -
8.4 Finishing walls with Premium Acrylic Smooth exterior paint with
Silicone additives of required shade:
a New work (Two or more coats applied @ 1.43 ltr/10 sqm
over and including priming coat of exterior primer applied
@ 2.20 kg/10 sqm)
2,200.00 sqm -
8.5 Prepare the surfaces of Grills with 1 coat of primer and 2 coats of
enamel paint of approved quality including necessary patty, cost of
materials, labour, etc. complete
44.22 sqm -
130.00 sqm -
ITEM No. DESCRIPTION OF ITEMS UNIT QTY UNIT RATE. TOTAL RATE
A STRUCTURAL WORKS
1.2
Filling over areas in basement and foundation with excavated earth/murrum brought
from within 500 M in the site, (boulders to be broken rolled), necessary excavation,
spreading in layers of 150mm thick to the required level including consolidation by
watering and ramming with mechanical device brought from outside as directed.
For Basement Cu. Mt 150.62 0
Filling in Foundations & Retaining wall Cu. Mt 121.89 0
1.3 Supply and Earth filling with approved soil brought from outside including, watering,
ramming consolidating and dressing complete. Depth 2.099M
For Basement Cu. Mt 136.25 0
Plain Cement Concrete in (1:4:8) proportion nominal mix for Foundations bed using
40mm size (SS5) hard Granite or Trap metal from approved quarry including cost and
conveyance of all materials like cement, sand, coarse aggregate, water, etc., to site,
including cost of seignior age charges and all other taxes on all materials and including all
labour charges for machine mixing, laying concrete, ramming, finishing top surface to the
required level, curing , etc., complete for finished item of work as directed by the
Engineer-in-charge.
Page 6 | 13
TENTATIVE BILL OF QUANTITIES OF STRUCTURAL WORK,
CONSTRUCTION OF PROPOSED FACTORY AT SULATNPUR, HYDERABAD. BELONGING TO MIDAS TOUCH
(1 BASEMENT + GROUND + 1 UPPER FLOOR + TERRACE FLOOR)
ITEM No. DESCRIPTION OF ITEMS UNIT QTY UNIT RATE. TOTAL RATE
Supply and Placing of the Ready Mix Concrete as per IS-4926:2003 of specified Grades
with minimum Cement content as per IS-456:2000 and standard mix Design as per IS-
10262:1982 with coarse aggregate of nominal size of 20mm and fine aggregate ( River
Sand) of Zone II as per the Mix design approved by the consultants from standard
suppliers as L & T, Birla, ACC or Equivalent , including cost and conveyance through transit
Mixers, Pumping, Leveling, grading, spreading, Vibrating & Curing etc., complete, including
the cost of mixing super plasticizer Sika " Sikament 600", Fosroc or equivalent with prior
approval of the Engineer in charge to enhance the workability of concrete, including the
cost of all materials , labour but excluding the cost of Reinforcement steel & Shuttering/
Formwork
Providing Centering, shuttering and scaffolding with props and 12mm thick Marine
Laminated Ply Sheets as per the approved shuttering plan and other accessories as per the
norms and stability calculations including cost and conveyance of all accessories etc,
complete for finished item of work. Using Cuplock System, Adjustable Jack screw Props
and Acrow span beams including all pipe bracings, clamps, couplings, cross members etc.,
complete for following items of work:
Page 7 | 13
TENTATIVE BILL OF QUANTITIES OF STRUCTURAL WORK,
CONSTRUCTION OF PROPOSED FACTORY AT SULATNPUR, HYDERABAD. BELONGING TO MIDAS TOUCH
(1 BASEMENT + GROUND + 1 UPPER FLOOR + TERRACE FLOOR)
ITEM No. DESCRIPTION OF ITEMS UNIT QTY UNIT RATE. TOTAL RATE
Providing High Yield Strength Deformed steel bars (Fe 500 grade as per IS:1786-1979) of
different diameters, including labour charges for cutting, bending to required sizes and
shapes, placing in position with cover blocks of approved materials and size and tying
firmly with MS binding wire of 20SWG, forming grills for reinforcement work as per
approved designs and drawings, including cost and conveyance of deformed steel bars,
including all wastages such as overlaps, couplings, welded joints, chairs, spacer bars
including cost and conveyance of binding wire, cover blocks and all incidental, operational,
labour charges such as cutting, bending, placing in position, tying , etc. including sales and
other taxes on all materials etc., complete for finished item of work in all floors. (Payment
will be made on the basis of weight of fabricated deformed bars only). Basic Rate
Rs.55,000 / MT
Providing fabricating, welding and/or bolting, as required, erecting and fixing in position all
types of structural steel works viz. columns beams, monorails, rafters, trusses, castellated
girder purlins, frame for louvers, bracing, staircase, Walkway, ladders and eage ladders,
sag rods pipe & cable racks and pipe bridges etc. (except for chequered plates, grating &
pipe railing only) made up of rolled or built up sections with moment or shear connections,
shop/site fabricated including all accessories via nuts, bolts, cleasts, gussets, suspenders
etc as per specification complete as directed by Engineer/Owner. The rate to include for
welding weights, site connection, nut & washer & bolts, scaffolding, working platform, etc
and same will not be measurement for payment (painting & sand blasting shall be paid
separately under relevant item). The rate shall include for preparing & providing detailed
fabrication drawings based on design drawing & getting the same approved from the
Engineer/ Owner.
0
WALL SHEETING SQM 427.00 0
ROOF SHEETING SQM 999.00 0
2.0 Facade
Structural Galzing 1620 0
Construction of OHT Lits 20000 0
3.0 M.S. HILTI ANCHOR BOLTS
Ground Floor
20 mm DIA No's 150
GRAND TOTAL -
OR SAY
Page 8 | 13
EXTERNAL DEVELOPMENT
Sl.No Description of Item Qty Unit Rate Amount Rs.
d BOUNDARY WALL
1 Earth work in excavation by mechanical or manual means
over areas of general site grading including dewatering if
required,including removal of shrubs, grass, bushes etc.
clearing of all objectionable materials sorting out of
excavated soil into serviceable and un- serviceable
materials, disposal or stacking of excavated material up to a
lead of 200m as directed etc. complete
1.1 In all types of soil soft murrum, hard murrum,In soft rock. 1,305.00 cum -
2 Earthwork in Filling to raise the ground level, including
watering and mechanical compaction in layers not
exceeding 150 mm in depth (each layer of filling to be
compacted to achieve level of compaction requirements
(98% maximum dry density ) at all elevations in area
filling as per specifications and drawings and as directed by
the Engineer, including land clearing, cutting of bush,
inside the plot area. (Net consolidated volume shall be
measured for payment)
1,305.00 cum -
3 Supplying and laying in position Plain Cement Concrete of
following nominal mixes (by volume) using graded crushed
stone as coarse aggregate of 20/40mm nominal size
including mixing, conveying, laying, compaction, curing
and Shuttering & centring etc., complete as per drawings,
specification.
2.00 Nos -
12 Providing and fixing welded Mild steel Compound wall
grill gate of size and design as per drawing areas openings
with necessary bolts & nets with necessary locking
arrangement etc. complete, as directed by Engineer in-
charge. The rate is inclusive of all materials , labour
charges ,loading,unloading, lead & lift ,hire and fuel
charges for tools and plants and other incidental charges
etc., complete.
2.00 Nos -
13 PVC pipe 125mm dia 30.00 Rm -
Total -
ROAD WORK
EARTH FORMATION
Earth work excavation for road formation in clay soil to
1 desired level 219.00 cum -
2 Preparing the road surface for formation of base layer
including rolling the surface to desired level 730.00 sqm
-
BASE FORMATION
3 Providing and laying of Granular sub base with clean,
crushed, graded aggregates and granular materials and
finish in accordance with the requirements of the 730.00 sqm
specifications to compacted thickness of 150 mm. -
4 Providing and laying of Wet Mix Macadam with clean,
crushed, graded aggregates and granular materials and
finish in accordance with the requirements of the
specifications to compacted thickness of 200 mm. 730.00 sqm -
ASPHALT LAYER
5 Providing and laying prime coat using 9.00kg of bituminous
Emulsion for 10 sq m over the newly laid WMM Surface,
preparatory to another construction over it..
730.00 sqm -
6 Providing and laying of Tack Coat using bituminous
Emulsion at the rate of 2.5 Kg per 10 Sqm over the Prime
coat, preparatory to another construction over it. 730.00 sqm -
7 Providing and laying 50 mm compacted thick Bituminous
macadam which work shall consist of construction in a
single course of compacted crushed aggregates premixed
with bituminous binder 60/70 grade at the rate of 3.5
percent by weight of total mix, to serve as base binder
course in accordance with the specifications and in
conformity with the drawing using CMP Plant and Paver
Finisher.
730.00 sqm -
8 Providing and laying of Tack Coat using bituminous
Emulsion at the rate of 2.5 Kg per 10 Sqm over the BM ,
preparatory to another construction over it. 730.00 sqm -
9 Providing and laying 25 mm thick semi dense bituminous
macadam of road surface, rolling with 10 tons vibro roller
include cost of all materials and labour. 730.00 sqm -
10 Supplying and laying R.C.C. NP3 class pipes in position
and grade for pipe culverts,including caulking the collar
with spun yarn soaked in neat cement slurry and finishing
the joint with 1:2 cement sand mortar, curing,etc., complete
as per drawings,specifica-tions and directions of Engineer-
In-Charge.
-
a 300 (dia other services) 25.00 Rm -
c 600 dia (pipe culvert) 25.00 Rm -
13 Providing & laying of kerb wall painting with two coats and
cleaning the surface of all dirt, scales, oil, grease etc. and
lining out complete approved by the Engineer-in-charge
200.00 Rm -
Total -
B PARKING AREA
1.1 In all types of soil soft murrum, hard murrum. In soft rock 403.39 cum -
2 Earthwork in Filling to raise the ground level, including
watering and mechanical compaction in layers not
exceeding 150 mm in depth (each layer of filling to be
compacted to achieve level of compaction requirements
(98% maximum dry density ) at all elevations in area
filling as per specifications and drawings and as directed by
the Engineer, including land clearing, cutting of bush,
inside the plot area. (Net consolidated volume shall be
measured for payment)
403.39 cum -
3 Supplying and laying in position Plain Cement Concrete of
following nominal mixes (by volume) using graded crushed
stone as coarse aggregate of 20/40mm nominal size
including mixing, conveying, laying, compaction, curing
and Shuttering & centring etc., complete as per drawings,
specification.
-
Mix 1:3:6 with 40 mm aggregate 100 mm thick 9.67 cum -
4 Supplying and laying in position design mix 'cement
concrete of following grades for Reinforced Cement
Concrete work in Foundation Raft,walls and slab& Sub in
all kinds of work using graded 'crushed stones as coarse
aggregate of 20mm Max size including 'mixing, conveying,
laying, compacting and 'curing etc. but excluding the cost of
Shuttering and Reinforcement complete as per, drawings
'specifications and directions of the Engineer.
-
M - 25 (Min cement content is 340 kg/cum 87.15 cum -
5 Supplying , installing dismantling and removing following
classes / class of Formworks for Foundation & Sub-
structures below plinth & upto Elevation (FFL) in all kinds
of work including necessary rendering of concrete surfaces
after exposure as per drawings, specification and direction
of Engineer
-
Plain Shuttering 314.53 sqm -
6 Supplying and laying in position TMT (Thermo
Mechanically Treated) Reinforcement Steel of Fe 500 grade
in all type of RCC work including straightening, strutting,
bending, binding with 18 gauge annealed steel wire
complete as speccified & as directed by Engineer in Charge.
10 Mt -
7 Providing and mixing integral crystaline water proofing
admix to the base slab concrete at the time of batching or in
the Transit Mixer at the project site as per site conditions
manufacturer recommendation and as detailed in technical
specification complete , work shall be carried out as per the
approved method of water proofing accepted by the
architect / Structural Consultant , work shall be guaranty for
ten years against leakage and gaurantee shall be provided in
the form of guantee bond as per the approved
proforma.using penetron admix of penetron- USA or
approved equivalant @0.8% by weight of cement
,resistance of 16 bar hydrostratic water head on negative
side.The Proposed admix should have" U" Sign Approval
for assuarance of safety to add in concrete. (The Rate is
inclusive of chemical compound)
314.53 sqm -
8 Supply and application of Penetron Slurry @ 1kg/sqmt on
the external side and inetrnal side of the UG Sump. 314.53 sqm -
9 Providing and fixing FRP rungs to concrete during
concreting of side wall to proper position and location as
per dwg and instruction of engineer in charge etc complete.
40 Nos -
10 All charges for Supplyand fixing RCC (600mm x600mm)
manhole covers etc complete as per the direction of
engineer in charge. 3 Nos -
11 Supplying and fixing waterstopper for construction joints 120 Rm -
TOTAL -
BASEMENT PIT COLLECTION 10000 LIT -
SWERAGE COLLECTION PIT 25000 LIT -
TOTAL -