Professional Documents
Culture Documents
One Tower - Substructure For GRC Panels at Retail - Concrete - Sep 7, 2021
One Tower - Substructure For GRC Panels at Retail - Concrete - Sep 7, 2021
73
www.hilti.com
Company: Page: 1
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Sep 7, 2021 (2) Date: 11/26/2021
Fastening point:
Specifier's comments:
1 Input data
Anchor type and diameter: KWIK HUS-EZ (KH-EZ) 5/8 (5)
Item number: 418080 KH-EZ 5/8"x5 1/2"
Effective embedment depth: hef = 98.6 mm, hnom = 127.0 mm
Material: Carbon Steel
Evaluation Service Report: ESR-3027
Issued I Valid: 1/1/2021 | 12/1/2021
Proof: Design Method ACI 318 / AC193
Stand-off installation: eb = 0.0 mm (no stand-off); t = 10.0 mm
Anchor plate :
R lx x ly x t = 185.0 mm x 200.0 mm x 10.0 mm; (Recommended plate thickness: not calculated)
Profile: no profile
Base material: cracked concrete, 2500, fc' = 2,500 psi; h = 240.0 mm
Reinforcement: tension: condition B, shear: condition B; no supplemental splitting reinforcement present
edge reinforcement: none or < No. 4 bar
Seismic loads (cat. C, D, E, or F) no
R
- The anchor calculation is based on a rigid anchor plate assumption.
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2021 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
1
Hilti PROFIS Engineering 3.0.73
www.hilti.com
Company: Page: 2
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Sep 7, 2021 (2) Date: 11/26/2021
Fastening point:
3 Tension load
Load Nua [lb] Capacity f Nn [lb] Utilization bN = Nua/f Nn Status
Steel Strength* 1,849 15,736 12 OK
Pullout Strength* N/A N/A N/A N/A
Concrete Breakout Failure** 3,720 3,853 97 OK
ANc [in. ]
2
ANc0 [in. ]
2
ca,min [mm] cac [mm] y c,N
200.71 135.49 60.0 147.8 1.000
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2021 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
2
Hilti PROFIS Engineering 3.0.73
www.hilti.com
Company: Page: 3
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Sep 7, 2021 (2) Date: 11/26/2021
Fastening point:
4 Shear load
Load Vua [lb] Capacity f Vn [lb] Utilization bV = Vua/f Vn Status
Steel Strength* N/A N/A N/A N/A
Steel failure (with lever arm)* N/A N/A N/A N/A
Pryout Strength* N/A N/A N/A N/A
Concrete edge failure in direction ** N/A N/A N/A N/A
5 Warnings
• The anchor design methods in PROFIS Engineering require rigid anchor plates per current regulations (AS 5216:2021, ETAG 001/Annex C,
EOTA TR029 etc.). This means load re-distribution on the anchors due to elastic deformations of the anchor plate are not considered - the
anchor plate is assumed to be sufficiently stiff, in order not to be deformed when subjected to the design loading. PROFIS Engineering
calculates the minimum required anchor plate thickness with CBFEM to limit the stress of the anchor plate based on the assumptions
explained above. The proof if the rigid anchor plate assumption is valid is not carried out by PROFIS Engineering. Input data and results
must be checked for agreement with the existing conditions and for plausibility!
• Condition A applies where the potential concrete failure surfaces are crossed by supplementary reinforcement proportioned to tie the
potential concrete failure prism into the structural member. Condition B applies where such supplementary reinforcement is not provided, or
where pullout or pryout strength governs.
• Refer to the manufacturer's product literature for cleaning and installation instructions.
• For additional information about ACI 318 strength design provisions, please go to
https://submittals.us.hilti.com/PROFISAnchorDesignGuide/
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2021 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
3
Hilti PROFIS Engineering 3.0.73
www.hilti.com
Company: Page: 4
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Sep 7, 2021 (2) Date: 11/26/2021
Fastening point:
6 Installation data
Anchor type and diameter: KWIK HUS-EZ (KH-EZ) 5/8 (5)
Profile: no profile Item number: 418080 KH-EZ 5/8"x5 1/2"
Hole diameter in the fixture: df = 19.1 mm Maximum installation torque: 0.115 kNm
Plate thickness (input): 10.0 mm Hole diameter in the base material: 15.9 mm
Recommended plate thickness: not calculated Hole depth in the base material: 136.5 mm
Drilling method: Hammer drilled Minimum thickness of the base material: 177.8 mm
Cleaning: Manual cleaning of the drilled hole according to instructions for use is
required.
Hilti KH-EZ screw anchor with 127 mm embedment, 5/8 (5), Carbon steel, installation per ESR-3027
y
92.5 92.5
60.0
100.0
3 4
10.0
100.0
x
100.0
1 2
40.0
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2021 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
4
Hilti PROFIS Engineering 3.0.73
www.hilti.com
Company: Page: 5
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Sep 7, 2021 (2) Date: 11/26/2021
Fastening point:
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2021 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan