Professional Documents
Culture Documents
Butterfly Flag Type (0+195, 0+120)
Butterfly Flag Type (0+195, 0+120)
1657.5
7500
Location = Ch 0 + 195
Existing Ground Level = 3.912
Finish Road Level = 5.678
Main Column Height = 9.175 m
Page 1
CALCULATION SHEET
PROJECT : Design of butterfly type flag Boards (Ch 0+195)
DESIGNED BY : CHECKED BY : DATE :
Reference Calculations Output
2.0 Wind Load Calculation
Assume site located 20m height from the mean sea level
Sa = 1.02
Sd = 1.00
Ss = 1.00
Sp = 1.00
So Vs = 34.17 ms-1
Sb = 1.81
Ve = 61.8477 ms-1
2
Dynamic pressure qs = 0.613Ve
= 2344.81 Pa2
Page 2
CALCULATION SHEET
PROJECT : Design of butterfly type flag Boards (Ch 0+195)
DESIGNED BY : CHECKED BY : DATE :
Reference Calculations Output
PULS = 49.20 kN
Vertical element
Span = 1.075 m.
From the property table 40 x 40 x 5.0 Equal angle (EA) can be selected
section modules = 1910 mm3
Page 3
CALCULATION SHEET
PROJECT : Design of butterfly type flag Boards (Ch 0+195)
DESIGNED BY : CHECKED BY : DATE :
Reference Calculations Output
Vertical EA to secodary beam connection
Dead load of the direction board and frame of the board was were
calculated manually and assigned to theelements by manually
Page 4
CALCULATION SHEET
PROJECT : Design of butterfly type flag Boards (Ch 0+195)
DESIGNED BY : CHECKED BY : DATE :
Reference Calculations Output
SAP Model
SAP Results
Page 5
CALCULATION SHEET
PROJECT : Design of butterfly type flag Boards (Ch 0+195)
DESIGNED BY : CHECKED BY : DATE :
Reference Calculations Output
Main Support
From the SAP Model
Design bending moment = 928.87 kNm
Design Shear force = 133.89 kN
Design axial force = 16.79 kN
Design torsion = 61.68 kNm
from the property table 457mm dia 16mm thick CHS can be selected
3
section modules = 3110 cm
So Moment Capacity Ok
So Shear Capacity Ok
Compression capacity ok
Fc Mx
+ < 1
pc Ag Mcx
0.0028 + 0.9197
0.9225 < 1 Cross section check is ok
Page 6
CALCULATION SHEET
PROJECT : Design of butterfly type flag Boards (Ch 0+195)
DESIGNED BY : CHECKED BY : DATE :
Reference Calculations Output
Secodary Element
from the property table 219.1 mm dia 12.5mm thick CHS can be selected
section modules = 534 cm3
So Moment capacity is ok
Since member is not subjected to both axial force and bending moment
cross section capacity should not be checkd for combine action
Page 7
CALCULATION SHEET
PROJECT : Design of butterfly type flag Boards (Ch 0+195)
DESIGNED BY : CHECKED BY : DATE :
Reference Calculations Output
Secondary element connection
100
M20 Bolt 12 Nos
(22mm Hole Size)
M20 Bolt 12 Nos (22mm Hole Size)
Tension Capacity if M16 Bolt = 0.8 x pt x At
420 mm Dia 12mm thick Base plate (S275)
(Grade 8.8) = 109.76 kN
Loads in ULS
Design Axial Force = 16.79 kN
Bending Moment = 1263.286 kNm
Page 8
CALCULATION SHEET
PROJECT : Design of butterfly type flag Boards (Ch 0+195)
DESIGNED BY : CHECKED BY : DATE :
Reference Calculations Output
Selected Dimension for foundation
2000
2750
1000
750
4500
750
100
500
2400
600
Overtrning check
Overtrning Moment = 971.76 kNm
Page 9
CALCULATION SHEET
PROJECT : Design of butterfly type flag Boards (Ch 0+195)
DESIGNED BY : CHECKED BY : DATE :
Reference Calculations Output
e = M/Q
= 1.28 m
B/6 = 0.833333
e > B/6
Option 2 = 4Q 150.59
3*L(B-2e)
Select Option 2
Maximum bering pressure = 150.59 kN/m2
Bearing capacity is ok
Sliding Check
Page 10
CALCULATION SHEET
PROJECT : Design of butterfly type flag Boards (Ch 0+195)
DESIGNED BY : CHECKED BY : DATE :
Reference Calculations Output
b = 1000 mm
d = 515 mm
fcu = 30 N/mm2
fy = 460 N/mm2
Mu = 0.15 fcubd2
Hence k = 0.15
k = 402.84 x 10^6
1000 x 515 x 515 x 30
= 0.051
< 0.150
Which is lesser than 0.15 ; can be designed as singly reinforcement
5Mu
Z 0.5d 1 1
fcubd 2
Z = 480.03 mm
Zmax = 0.95d
= 489.25 mm
Z =
Z = 480.03 mm 480.03 mm
Mu = 0.87 fy As Z
As = Mu
0.87 fy Z
As req =
2 2
As = 2097.00 mm 2097 mm
100As / bd = 0.41 > 0.15
Min main R/F area 0.15% of bad = 1000 x 515 x 0.15 % As min =
2 2
As min = 772.5 mm 772.50 mm
As req > As min
Hence select As req
Page 11
CALCULATION SHEET
PROJECT : Design of butterfly type flag Boards (Ch 0+195)
DESIGNED BY : CHECKED BY : DATE :
Reference Calculations Output
Spacing of bar = 1000 / 6.67
= 150 mm
Secondary Reinforcement
No Of bars = 7.13
Page 12