Professional Documents
Culture Documents
Instruction Sheet Is Mh8412 - STYLE NUMBER MH8412BD, MH8412BD01
Instruction Sheet Is Mh8412 - STYLE NUMBER MH8412BD, MH8412BD01
Instruction Sheet Is Mh8412 - STYLE NUMBER MH8412BD, MH8412BD01
6 CORPORATE PARKWAY
GOOSE CREEK , SC . 29445
www . quoizel . com
STYLE NUMBER : MH8412BD,MH8412BD01
I
M
J
1 OF 5
INSTALLATION INSTRUCTIONS STYLE NUMBER : MH8412BD,MH8412BD01
STEP 1:
a . Screw the Mounting Screws into the Crossbar , place the
Lock Washers over the Mounting Screws and thread the Crossbar
Outlet Box
Hex Nuts onto the Mounting Screws as shown . Secure the Lock Washer
position of the Mounting Screws by tightening the Hex Nuts Mounting Hex Nut
against the Crossbar . Screw
b. Place the Crossbar onto the Wall surface and line up one
set of holes onto mounting holes on Outlet Box. Using a
pencil, mark the locations for Wall Anchors.
c. Remove the Crossbar and drill holes from the marks and
then push the Wall Anchors into the holes.
d. Position the Crossbar back onto the Wall, secure by Outlet Box
threading the Outlet Box Screws into the mounting holes Screw
on the Outlet Box and screw Self-tapping Screws into the
Wall Anchors. Tighten until snug.
STEP 2 :
a . Locate the Backplate onto the Crossbar and slip the Button Crossbar
Stop on the end of Lanyard into the Slot on the Crossbar as
shown. Button Stop
Lanyard
Slot
Backplate
STEP 3 :
* Use Wire Connectors ( not supplied ) to connect the WHITE OR RIBBED WHITE OR RIBBED
wires . FROM HOUSE FROM FIXTURE
a . Connect the House Ground Wire to the Fixture Ground
Wire.
b . Connect the House White ( or Ribbed ) Wire to the BLACK ( OR RED ) WIRE BLACK OR SMOOTH
Fixture Supply Wire ( White or Ribbed Side ) .
FROM FIXTURE
c . Connect the House Black ( or Red ) Wire to the Fixture FROM HOUSE
Supply Wire ( Black or Smooth Side ).
d . Wrap each connection with approved electrical tape and
GROUND WIRE GROUND WIRE
carefully stuff all of the connected wires into the Outlet
Box . FROM HOUSE FROM FIXTURE
2 OF 5
INSTALLATION INSTRUCTIONS STYLE NUMBER : MH8412BD,MH8412BD01
STEP 4 :
a . Place the Backplate over the Mounting Screws and secure
with Mounting Balls. Hand tighten until snug.
Backplate
Mounting Mounting
Screw Ball
STEP 5:
a . Install correct bulbs referring to fixture markings and / or labels for maximum wattage .
STEP 6 :
a . Place the Glass Panel inside of the Cage as shown . Glass Panel
b . Place Tabs onto the top edge of the Glass Panels and
match the holes on the Tabs onto Mounting Holes on
the top edge of the Cage . Tab
c . Using screwdriver , thread Lock Screws into Mounting
Lock Screw
Holes and hand tighten until snug to secure Glass
Panels .
Cage
Cage
3 OF 5
INSTALLATION INSTRUCTIONS STYLE NUMBER : MH8412BD,MH8412BD01
STEP 7 :
a . Lift the Cage with Glass Panels upward, pass the center
hole on the bottom of the Cage over the Nipple on the
bottom of the Socket Assembly. Secure with the Finial and
tighten until snug.
Socket Assembly
Nipple
Cage with
Glass Panels
Finial
STEP 8 :
a . Refer to following information for caulking instructions :
MOUNTING BALL
4 OF 5
INSTALLATION INSTRUCTIONS STYLE NUMBER : MH8412BD,MH8412BD01
With the OUTDOOR FIXTURE properly installed in accordance with supplied Assembly/installation
instructions, proceed with caulking instructions below.
Note: Be sure EXTERIOR WALL SURFACE and FIXTURE BACKPLATE are free to dirt to caulking.
Using EXTERIOR GRADE CAULK, start on one side of FIXTURE BACKPLATE and follow contour, were
the FIXTURE BACKPLATE meets the EXTERIOR WALL SURFACE upward. Proceed to caulk over top of
backplate and down other side. DO NOT CAULK BOTTOM OF FIXTURE BACKPLATE to ensure proper
moisture drainage.
EXTERIOR GRADE
CAULK
OUTDOOR
FIXTURE BACKPLATE
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
5 OF 5