Professional Documents
Culture Documents
Front Track Roller Frame - Install CAT D9T
Front Track Roller Frame - Install CAT D9T
Welcome: j210akw
Product: TRACK-TYPE TRACTOR
Model: D9T TRACK-TYPE TRACTOR TWG
Configuration: D9T TRACK-TYPE TRACTOR TWG00001-UP (MACHINE)
POWERED BY C18 Engine
i02208081
Installation Procedure
Table 1
Required Tools
A FT-2223 Strap 1
4C-6486 Stand 1
8S-7621 Tube 1
B
8S-8048 Saddle 1
8S-7615 Pin 1
1 of 5 4/26/2018, 4:11 PM
D9T TRACK-TYPE TRACTOR TWG00001-UP (MACHINE) PO... https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?retu...
Illustration 1 g00770832
1. Install bearing (10) and retaining ring (11). Use Tooling (F) in order to install seal (12). Install retaining ring
(13) .
Illustration 2 g01108012
2 of 5 4/26/2018, 4:11 PM
D9T TRACK-TYPE TRACTOR TWG00001-UP (MACHINE) PO... https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?retu...
Illustration 3 g01107793
3. Attach a suitable lifting device and Tooling (D) in order to support the rear of front track roller frame (9).
The weight of front track roller frame (9) is approximately 1565 kg (3450 lb). Install front track roller frame
(9) until the suitable lifting device contacts rear track roller frame (2). Remove the suitable lifting device.
Illustration 4 g01108023
4. Position a chain around the idler. Attach the chain to the rear track roller frame and to Tooling (D). Remove
Tooling (E). Use Tooling (D) and install front track roller frame (9) into rear track roller frame (2) .
3 of 5 4/26/2018, 4:11 PM
D9T TRACK-TYPE TRACTOR TWG00001-UP (MACHINE) PO... https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?retu...
Illustration 5 g00771640
5. Install guide assembly (8) on the outside of rear track roller frame (2) .
Illustration 6 g01108101
Note: Check the O-ring seal for wear or for damage. If necessary, replace the O-ring seal.
6. Install O-ring seal (6) on cover (5). Install cover (5). Install bolts (4). Tighten bolts (4) to a torque of 215 ± 40
N·m (159 ± 30 lb ft).
7. Repeat Steps 5 and 6 for the inside of rear track roller frame (2) .
4 of 5 4/26/2018, 4:11 PM
D9T TRACK-TYPE TRACTOR TWG00001-UP (MACHINE) PO... https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?retu...
Illustration 7 g01107219
8. Connect track (3). Raise the blade and remove Tooling (B). Remove Tooling (A). Remove the suitable
cribbing.
9. Fill the recoil spring compartment with oil. Refer to Operation and Maintenance Manual, "Recoil Spring
Compartment Oil Level - Check" and Operation and Maintenance Manual, "Capacities (Refill)".
10. Tighten the track. Refer to Operation and Maintenance Manual, "Track - Check/Adjust".
Copyright 1993 - 2018 Caterpillar Inc. Thu Apr 26 2018 16:10:54 GMT+0800 (Malay Peninsula Standard Time)
All Rights Reserved.
j210akw
Private Network For SIS Licensees.
5 of 5 4/26/2018, 4:11 PM