Professional Documents
Culture Documents
BE (Mechanical) SEM-1 IN SEM EXAM 2021 402045 A - AUTOMOBILE ENGINEERING (Elective - II) (Pattern - 2015)
BE (Mechanical) SEM-1 IN SEM EXAM 2021 402045 A - AUTOMOBILE ENGINEERING (Elective - II) (Pattern - 2015)
Draft saved
* Required
AUTOMOBILE ENGINEERING
The six planetary pinions rotate in constant mesh with the internal gears
One drive shaft is splined to the central gear and the other to the planetary gear.
Each planetary pinion gear meshes with both the central gear and the internal gear.
https://docs.google.com/forms/d/e/1FAIpQLSftJge5_96qmQ2wX3VvMI5KufdeRUwS4CcWl-6v0NNS79lL_g/formResponse 1/10
27/10/2021, 15:30 BE(Mechanical) SEM-1 IN SEM EXAM 2021 402045 A - AUTOMOBILE ENGINEERING (Elective – II) (Pattern -2015)
Van
starbus
TATA ACE
In a four wheel drive (4WD), the numbers of gear boxes are * 1 point
15
50
100
https://docs.google.com/forms/d/e/1FAIpQLSftJge5_96qmQ2wX3VvMI5KufdeRUwS4CcWl-6v0NNS79lL_g/formResponse 2/10
27/10/2021, 15:30 BE(Mechanical) SEM-1 IN SEM EXAM 2021 402045 A - AUTOMOBILE ENGINEERING (Elective – II) (Pattern -2015)
Constant-mesh gearbox
Synchromesh gearbox
Epicyclical gearbox
Bend sideways
Change inclination
The angle formed by the line joining the stub axle-steering arm ball joints 1 point
with the vertical, when this line slants forward at the top is called *
Positive camber
Negative camber
Positive castor
Negative castor
https://docs.google.com/forms/d/e/1FAIpQLSftJge5_96qmQ2wX3VvMI5KufdeRUwS4CcWl-6v0NNS79lL_g/formResponse 3/10
27/10/2021, 15:30 BE(Mechanical) SEM-1 IN SEM EXAM 2021 402045 A - AUTOMOBILE ENGINEERING (Elective – II) (Pattern -2015)
roll
pitch
yaw
dip
Bronze bushes
Rubber bushes
Steel bushes
Metal bushes
One purpose of a recirculating ball type steering gear is to reduce the * 1 point
Operating friction
Operating cost
Number of parts.
https://docs.google.com/forms/d/e/1FAIpQLSftJge5_96qmQ2wX3VvMI5KufdeRUwS4CcWl-6v0NNS79lL_g/formResponse 4/10
27/10/2021, 15:30 BE(Mechanical) SEM-1 IN SEM EXAM 2021 402045 A - AUTOMOBILE ENGINEERING (Elective – II) (Pattern -2015)
The cooling system of an automobile engine is simple when the engine is 1 point
placed at the *
front
centre
Free wheel
Stator
Rotor
impeller
https://docs.google.com/forms/d/e/1FAIpQLSftJge5_96qmQ2wX3VvMI5KufdeRUwS4CcWl-6v0NNS79lL_g/formResponse 5/10
27/10/2021, 15:30 BE(Mechanical) SEM-1 IN SEM EXAM 2021 402045 A - AUTOMOBILE ENGINEERING (Elective – II) (Pattern -2015)
The bearing is located between the axle casing and the inner side of wheel 1 point
hub called as *
semi floating
fully floating
none of these
Increase traction
Due to weight transfer, the ratio of braking effect at the front and at the 1 point
rear wheels should be *
https://docs.google.com/forms/d/e/1FAIpQLSftJge5_96qmQ2wX3VvMI5KufdeRUwS4CcWl-6v0NNS79lL_g/formResponse 6/10
27/10/2021, 15:30 BE(Mechanical) SEM-1 IN SEM EXAM 2021 402045 A - AUTOMOBILE ENGINEERING (Elective – II) (Pattern -2015)
Calliper
Piston
Piston seal
Bleed screw
truck
articulated vehicle
coach
van
Fluid clutch
Centrifugal clutch
Cone clutch
Disc clutch
https://docs.google.com/forms/d/e/1FAIpQLSftJge5_96qmQ2wX3VvMI5KufdeRUwS4CcWl-6v0NNS79lL_g/formResponse 7/10
27/10/2021, 15:30 BE(Mechanical) SEM-1 IN SEM EXAM 2021 402045 A - AUTOMOBILE ENGINEERING (Elective – II) (Pattern -2015)
What is the angle between the steering axis and the vertical in the plane of 1 point
the wheel? *
Castor
Camber
Kingpin inclination
Two wheelers
Cars
Trucks
Trailers
Engine drive shafts, clutch, main shaft, counter shaft, final driven gear, wheels
Engine clutch, main shaft, counter shaft, final driven gear, drive shafts, wheels
Engine clutch, counter shaft, main shaft, final driven gear, drive shafts, wheels
Engine main shaft, counter shaft, clutch, final driven gear, drive shafts, wheels
https://docs.google.com/forms/d/e/1FAIpQLSftJge5_96qmQ2wX3VvMI5KufdeRUwS4CcWl-6v0NNS79lL_g/formResponse 8/10
27/10/2021, 15:30 BE(Mechanical) SEM-1 IN SEM EXAM 2021 402045 A - AUTOMOBILE ENGINEERING (Elective – II) (Pattern -2015)
Vertical loading
Driving thrust
Side thrust
Braking torque
Release energy
Solid woven
Moulded type
Laminated
none of these
https://docs.google.com/forms/d/e/1FAIpQLSftJge5_96qmQ2wX3VvMI5KufdeRUwS4CcWl-6v0NNS79lL_g/formResponse 9/10
27/10/2021, 15:30 BE(Mechanical) SEM-1 IN SEM EXAM 2021 402045 A - AUTOMOBILE ENGINEERING (Elective – II) (Pattern -2015)
Disc wheel
Wire wheel
Page 2 of 2
This form was created inside of Sinhgad Technical Education Society. Report Abuse
Forms
https://docs.google.com/forms/d/e/1FAIpQLSftJge5_96qmQ2wX3VvMI5KufdeRUwS4CcWl-6v0NNS79lL_g/formResponse 10/10